Resguardo inicial

linux-7.2.3/Documentation/devicetree/bindings/extcon/extcon-max3355.txt

@@ -0,0 +1,21 @@
+Maxim Integrated MAX3355 USB OTG chip
+-------------------------------------
+
+MAX3355 integrates a charge pump and comparators to enable a system with an
+integrated USB OTG dual-role transceiver to function as a USB OTG dual-role
+device.
+
+Required properties:
+- compatible: should be "maxim,max3355";
+- maxim,shdn-gpios: should contain a phandle and GPIO specifier for the GPIO pin
+		    connected to the MAX3355's SHDN# pin;
+- id-gpios: should contain a phandle and GPIO specifier for the GPIO pin
+	    connected to the MAX3355's ID_OUT pin.
+
+Example:
+
+	usb-otg {
+		compatible = "maxim,max3355";
+		maxim,shdn-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+		id-gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>;
+	};

linux-7.2.3/Documentation/devicetree/bindings/extcon/extcon-palmas.txt

@@ -0,0 +1,22 @@
+EXTCON FOR PALMAS/TWL CHIPS
+
+PALMAS USB COMPARATOR
+Required Properties:
+ - compatible: should contain one of:
+   * "ti,palmas-usb-vid".
+   * "ti,twl6035-usb-vid".
+   * "ti,palmas-usb" (DEPRECATED - use "ti,palmas-usb-vid").
+   * "ti,twl6035-usb" (DEPRECATED - use "ti,twl6035-usb-vid").
+
+Optional Properties:
+ - ti,wakeup : To enable the wakeup comparator in probe
+ - ti,enable-id-detection: Perform ID detection. If id-gpio is specified
+		it performs id-detection using GPIO else using OTG core.
+ - ti,enable-vbus-detection: Perform VBUS detection.
+ - id-gpio: gpio for GPIO ID detection. See gpio binding.
+ - debounce-delay-ms: debounce delay for GPIO ID pin in milliseconds.
+
+palmas-usb {
+       compatible = "ti,twl6035-usb", "ti,palmas-usb";
+       ti,wakeup;
+};

linux-7.2.3/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml

@@ -0,0 +1,76 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/extcon-ptn5150.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PTN5150 CC (Configuration Channel) Logic device
+
+maintainers:
+  - Krzysztof Kozlowski <krzk@kernel.org>
+
+description: |
+  PTN5150 is a small thin low power CC logic chip supporting the USB Type-C
+  connector application with CC control logic detection and indication
+  functions.  It is interfaced to the host controller using an I2C interface.
+
+properties:
+  compatible:
+    const: nxp,ptn5150
+
+  int-gpios:
+    maxItems: 1
+    deprecated: true
+    description:
+      GPIO pin (input) connected to the PTN5150's INTB pin.
+      Use "interrupts" instead.
+
+  interrupts:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+  vbus-gpios:
+    maxItems: 1
+    description:
+      GPIO pin (output) used to control VBUS. If skipped, no such control
+      takes place.
+
+  port:
+    $ref: /schemas/graph.yaml#/properties/port
+    description:
+      A port node to link the usb controller for the dual role switch.
+
+  connector:
+    $ref: /schemas/connector/usb-connector.yaml#
+
+required:
+  - compatible
+  - interrupts
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ptn5150@1d {
+            compatible = "nxp,ptn5150";
+            reg = <0x1d>;
+            interrupt-parent = <&msmgpio>;
+            interrupts = <78 IRQ_TYPE_LEVEL_HIGH>;
+            vbus-gpios = <&msmgpio 148 GPIO_ACTIVE_HIGH>;
+
+            port {
+                endpoint {
+                    remote-endpoint = <&usb1_drd_sw>;
+                };
+            };
+        };
+    };

linux-7.2.3/Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.yaml

@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/extcon-usbc-cros-ec.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ChromeOS EC USB Type-C cable and accessories detection
+
+maintainers:
+  - Benson Leung <bleung@chromium.org>
+
+description: |
+  On ChromeOS systems with USB Type C ports, the ChromeOS Embedded Controller is
+  able to detect the state of external accessories such as display adapters
+  or USB devices when said accessories are attached or detached.
+  The node for this device must be under a cros-ec node like google,cros-ec-spi
+  or google,cros-ec-i2c.
+
+properties:
+  compatible:
+    const: google,extcon-usbc-cros-ec
+
+  google,usb-port-id:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: the port id
+    minimum: 0
+    maximum: 255
+
+required:
+  - compatible
+  - google,usb-port-id
+
+additionalProperties: false
+
+examples:
+  - |
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        cros-ec@0 {
+            compatible = "google,cros-ec-spi";
+            reg = <0>;
+            interrupts = <44 0>;
+
+            usbc_extcon0: extcon0 {
+                compatible = "google,extcon-usbc-cros-ec";
+                google,usb-port-id = <0>;
+            };
+
+            usbc_extcon1: extcon1 {
+                compatible = "google,extcon-usbc-cros-ec";
+                google,usb-port-id = <1>;
+            };
+        };
+    };

linux-7.2.3/Documentation/devicetree/bindings/extcon/extcon-usbc-tusb320.yaml

@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/extcon-usbc-tusb320.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI TUSB320 USB Type-C CC Logic controller
+
+maintainers:
+  - Michael Auchter <michael.auchter@ni.com>
+
+properties:
+  compatible:
+    enum:
+      - ti,tusb320
+      - ti,tusb320l
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        tusb320@61 {
+            compatible = "ti,tusb320";
+            reg = <0x61>;
+            interrupt-parent = <&gpio>;
+            interrupts = <27 1>;
+        };
+    };
+...

linux-7.2.3/Documentation/devicetree/bindings/extcon/fcs,fsa880.yaml

@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/fcs,fsa880.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Fairchild Semiconductor FSA880, FSA9480 and compatibles
+
+maintainers:
+  - Linus Walleij <linusw@kernel.org>
+
+description:
+  The FSA880 and FSA9480 are USB port accessory detectors and switches.
+  The switch is fully controlled using I2C and enables USB data, stereo
+  and mono audio, video, microphone, and UART data to use a common
+  connector port. Compatible switches exist from other manufacturers.
+
+properties:
+  compatible:
+    enum:
+      - fcs,fsa880
+      - fcs,fsa9480
+      - ti,tsu6111
+
+  reg:
+    maxItems: 1
+    description: The I2C address for an FSA880 compatible device is
+      usually 0x25.
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        usb-switch@25 {
+            compatible = "fcs,fsa880";
+            reg = <0x25>;
+            interrupt-parent = <&gpio>;
+            interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+        };
+    };

linux-7.2.3/Documentation/devicetree/bindings/extcon/linux,extcon-usb-gpio.yaml

@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/linux,extcon-usb-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: USB GPIO Extcon device
+
+maintainers:
+  - Frank Li <Frank.Li@nxp.com>
+
+description:
+  This is a virtual device used to generate USB cable states from the USB ID pin
+  connected to a GPIO pin.
+
+properties:
+  compatible:
+    const: linux,extcon-usb-gpio
+
+  id-gpios:
+    description: gpio for USB ID pin. See gpio binding.
+  vbus-gpios:
+    description: gpio for USB VBUS pin.
+
+required:
+  - compatible
+
+anyOf:
+  - required:
+      - id-gpios
+  - required:
+      - vbus-gpios
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    extcon_usb1 {
+        compatible = "linux,extcon-usb-gpio";
+        id-gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>;
+    };

linux-7.2.3/Documentation/devicetree/bindings/extcon/maxim,max14526.yaml

@@ -0,0 +1,80 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/maxim,max14526.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Maxim MAX14526 MicroUSB Integrated Circuit (MUIC)
+
+maintainers:
+  - Svyatoslav Ryhel <clamor95@gmail.com>
+
+properties:
+  compatible:
+    const: maxim,max14526
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  connector:
+    $ref: /schemas/connector/usb-connector.yaml#
+
+  port:
+    $ref: /schemas/graph.yaml#/properties/port
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - connector
+  - port
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        muic@44 {
+            compatible = "maxim,max14526";
+            reg = <0x44>;
+
+            interrupt-parent = <&gpio>;
+            interrupts = <72 IRQ_TYPE_EDGE_FALLING>;
+
+            connector {
+                compatible = "usb-b-connector";
+                label = "micro-USB";
+                type = "micro";
+            };
+
+            port {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                muic_to_charger: endpoint@0 {
+                    reg = <0>;
+                    remote-endpoint = <&charger_input>;
+                };
+
+                muic_to_usb: endpoint@1 {
+                    reg = <1>;
+                    remote-endpoint = <&usb_input>;
+                };
+
+                muic_to_mhl: endpoint@2 {
+                    reg = <2>;
+                    remote-endpoint = <&mhl_input>;
+                };
+            };
+        };
+    };
+...

linux-7.2.3/Documentation/devicetree/bindings/extcon/maxim,max77843.yaml

@@ -0,0 +1,41 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/maxim,max77843.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Maxim MAX77843 MicroUSB and Companion Power Management IC Extcon
+
+maintainers:
+  - Chanwoo Choi <cw00.choi@samsung.com>
+  - Krzysztof Kozlowski <krzk@kernel.org>
+
+description: |
+  This is a part of device tree bindings for Maxim MAX77843 MicroUSB
+  Integrated Circuit (MUIC).
+
+  See also Documentation/devicetree/bindings/mfd/maxim,max77843.yaml for
+  additional information and example.
+
+properties:
+  compatible:
+    const: maxim,max77843-muic
+
+  connector:
+    $ref: /schemas/connector/usb-connector.yaml#
+    unevaluatedProperties: false
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+    description:
+      Any connector to the data bus of this controller should be modelled using
+      the OF graph bindings specified
+    properties:
+      port:
+        $ref: /schemas/graph.yaml#/properties/port
+
+required:
+  - compatible
+  - connector
+
+additionalProperties: false

linux-7.2.3/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.yaml

@@ -0,0 +1,66 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/qcom,pm8941-misc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. PM8941 USB ID Extcon device
+
+maintainers:
+  - Guru Das Srinagesh <quic_gurus@quicinc.com>
+
+description: |
+  Some Qualcomm PMICs have a "misc" module that can be used to detect when
+  the USB ID pin has been pulled low or high.
+
+properties:
+  compatible:
+    items:
+      - const: qcom,pm8941-misc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    minItems: 1
+    maxItems: 2
+
+  interrupt-names:
+    minItems: 1
+    anyOf:
+      - items:
+          - const: usb_id
+          - const: usb_vbus
+      - items:
+          - const: usb_id
+      - items:
+          - const: usb_vbus
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    pmic {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            interrupt-controller;
+            #interrupt-cells = <4>;
+
+            usb_id: usb-detect@900 {
+                    compatible = "qcom,pm8941-misc";
+                    reg = <0x900>;
+                    interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
+                    interrupt-names = "usb_id";
+            };
+    };
+
+    usb-controller {
+           extcon = <&usb_id>;
+    };

linux-7.2.3/Documentation/devicetree/bindings/extcon/richtek,rt8973a-muic.yaml

@@ -0,0 +1,49 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/richtek,rt8973a-muic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Richtek RT8973A MUIC
+
+maintainers:
+  - Chanwoo Choi <cw00.choi@samsung.com>
+
+description:
+  The Richtek RT8973A is Micro USB Switch with OVP and I2C interface. The RT8973A
+  is a USB port accessory detector and switch that is optimized to protect low
+  voltage system from abnormal high input voltage (up to 28V) and supports high
+  speed USB operation. Also, RT8973A support 'auto-configuration' mode.
+  If auto-configuration mode is enabled, RT8973A would control internal h/w patch
+  for USB D-/D+ switching.
+
+properties:
+  compatible:
+    const: richtek,rt8973a-muic
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        usb-switch@14 {
+          compatible = "richtek,rt8973a-muic";
+          reg = <0x14>;
+          interrupt-parent = <&gpio>;
+          interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+        };
+    };

linux-7.2.3/Documentation/devicetree/bindings/extcon/samsung,s2mu005-muic.yaml

@@ -0,0 +1,40 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/samsung,s2mu005-muic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MUIC Device for Samsung S2M series PMICs
+
+maintainers:
+  - Kaustabh Chakraborty <kauschluss@disroot.org>
+
+description: |
+  The Samsung S2M series PMIC MUIC device is a USB port accessory
+  detector. It reports multiple states depending on the ID-GND
+  resistance measured by an internal ADC.
+
+  This is a part of device tree bindings for S2M and S5M family of Power
+  Management IC (PMIC).
+
+  See also Documentation/devicetree/bindings/mfd/samsung,s2mps11.yaml for
+  additional information and example.
+
+properties:
+  compatible:
+    enum:
+      - samsung,s2mu005-muic
+
+  connector:
+    $ref: /schemas/connector/usb-connector.yaml#
+
+  port:
+    $ref: /schemas/graph.yaml#/properties/port
+    description: Port connecting to the USB controller or PHY.
+
+required:
+  - compatible
+  - connector
+  - port
+
+additionalProperties: false

linux-7.2.3/Documentation/devicetree/bindings/extcon/siliconmitus,sm5502-muic.yaml

@@ -0,0 +1,57 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/siliconmitus,sm5502-muic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SM5502/SM5504 MUIC (Micro-USB Interface Controller) device
+
+maintainers:
+  - Chanwoo Choi <cw00.choi@samsung.com>
+
+description:
+  The Silicon Mitus SM5502 is a MUIC (Micro-USB Interface Controller) device
+  which can detect the state of external accessory when external accessory is
+  attached or detached and button is pressed or released. It is interfaced to
+  the host controller using an I2C interface.
+
+properties:
+  compatible:
+    enum:
+      - siliconmitus,sm5502-muic
+      - siliconmitus,sm5504-muic
+      - siliconmitus,sm5703-muic
+
+  reg:
+    maxItems: 1
+    description: I2C slave address of the device. Usually 0x25 for SM5502
+      and SM5703, 0x14 for SM5504.
+
+  connector:
+    $ref: /schemas/connector/usb-connector.yaml#
+    unevaluatedProperties: false
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        extcon@25 {
+                compatible = "siliconmitus,sm5502-muic";
+                reg = <0x25>;
+                interrupt-parent = <&msmgpio>;
+                interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+        };
+    };

linux-7.2.3/Documentation/devicetree/bindings/extcon/wlf,arizona.yaml

@@ -0,0 +1,126 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/wlf,arizona.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic/Wolfson Microelectronics Arizona class audio SoCs
+
+maintainers:
+  - patches@opensource.cirrus.com
+
+description: |
+  These devices are audio SoCs with extensive digital capabilities and a
+  range of analogue I/O.
+
+  This document lists Extcon specific bindings, see the primary binding
+  document ../mfd/arizona.yaml
+
+properties:
+  wlf,hpdet-channel:
+    description:
+      Headphone detection channel.  ARIZONA_ACCDET_MODE_HPL/1 sets the
+      headphone detect mode to HPDETL, ARIZONA_ACCDET_MODE_HPR/2 sets it
+      to HPDETR.  If this node is not included or if the value is unknown,
+      then headphone detection mode is set to HPDETL.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 1
+    maximum: 2
+
+  wlf,use-jd2:
+    description:
+      Use the additional JD input along with JD1 for dual pin jack detection.
+    type: boolean
+
+  wlf,use-jd2-nopull:
+    description:
+      Internal pull on JD2 is disabled when used for jack detection.
+    type: boolean
+
+  wlf,jd-invert:
+    description:
+      Invert the polarity of the jack detection switch.
+    type: boolean
+
+  wlf,micd-software-compare:
+    description:
+      Use a software comparison to determine mic presence.
+    type: boolean
+
+  wlf,micd-detect-debounce:
+    description:
+      Additional software microphone detection debounce specified in
+      milliseconds.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  wlf,micd-pol-gpio:
+    description:
+      GPIO specifier for the GPIO controlling the headset polarity if one
+      exists.
+    maxItems: 1
+
+  wlf,micd-bias-start-time:
+    description:
+      Time allowed for MICBIAS to startup prior to performing microphone
+      detection, specified as per the ARIZONA_MICD_TIME_XXX defines.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 12
+
+  wlf,micd-rate:
+    description:
+      Delay between successive microphone detection measurements, specified
+      as per the ARIZONA_MICD_TIME_XXX defines.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 12
+
+  wlf,micd-dbtime:
+    description:
+      Microphone detection hardware debounces specified as the number of
+      measurements to take.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [2, 4]
+
+  wlf,micd-timeout-ms:
+    description:
+      Timeout for microphone detection, specified in milliseconds.
+
+  wlf,micd-force-micbias:
+    description:
+      Force MICBIAS continuously on during microphone detection.
+    type: boolean
+
+  wlf,micd-configs:
+    description:
+      Headset polarity configurations (generally used for detection of
+      CTIA / OMTP headsets), the field can be of variable length but
+      should always be a multiple of 3 cells long, each three cell group
+      represents one polarity configuration.
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
+    items:
+      items:
+        - description:
+            The first cell defines the accessory detection pin, zero
+            will use MICDET1 and 0x2000 will use MICDET2.
+          enum: [ 0, 0x2000 ]
+        - description:
+            The second cell represents the MICBIAS to be used. Zero
+            will use MICVDD, 1-3 will use MICBIASx.
+          minimum: 0
+          maximum: 3
+        - description:
+            The third cell represents the value of the micd-pol-gpio
+            pin.
+          minimum: 0
+          maximum: 1
+
+  wlf,gpsw:
+    description:
+      Settings for the general purpose switch, set as one of the
+      ARIZONA_GPSW_XXX defines.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 3
+
+additionalProperties: true