Resguardo inicial

linux-7.2.3/arch/arm/boot/dts/cirrus/Makefile

@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_CLPS711X) += \
+	ep7211-edb7211.dtb
+dtb-$(CONFIG_ARCH_CLPS711X) += \
+	ep7211-edb7211.dtb
+dtb-$(CONFIG_ARCH_EP93XX) += \
+	ep93xx-edb9302.dtb \
+	ep93xx-bk3.dtb \
+	ep93xx-ts7250.dtb

linux-7.2.3/arch/arm/boot/dts/cirrus/ep7209.dtsi

@@ -0,0 +1,201 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+/dts-v1/;
+
+#include <dt-bindings/clock/clps711x-clock.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Cirrus Logic EP7209";
+	compatible = "cirrus,ep7209";
+
+	chosen { };
+
+	aliases {
+		gpio0 = &porta;
+		gpio1 = &portb;
+		gpio3 = &portd;
+		gpio4 = &porte;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		spi0 = &spi;
+		timer0 = &timer1;
+		timer1 = &timer2;
+	};
+
+	cpus {
+		#address-cells = <0>;
+		#size-cells = <0>;
+
+		cpu {
+			device_type = "cpu";
+			compatible = "arm,arm720t";
+		};
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		interrupt-parent = <&intc>;
+		ranges;
+
+		clks: clks@80000000 {
+			#clock-cells = <1>;
+			compatible = "cirrus,ep7209-clk";
+			reg = <0x80000000 0xc000>;
+			startup-frequency = <73728000>;
+		};
+
+		intc: intc@80000000 {
+			compatible = "cirrus,ep7209-intc";
+			reg = <0x80000000 0x4000>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		porta: gpio@80000000 {
+			compatible = "cirrus,ep7209-gpio";
+			reg = <0x80000000 0x1 0x80000040 0x1>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		portb: gpio@80000001 {
+			compatible = "cirrus,ep7209-gpio";
+			reg = <0x80000001 0x1 0x80000041 0x1>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		portd: gpio@80000003 {
+			compatible = "cirrus,ep7209-gpio";
+			reg = <0x80000003 0x1 0x80000043 0x1>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		porte: gpio@80000083 {
+			compatible = "cirrus,ep7209-gpio";
+			reg = <0x80000083 0x1 0x800000c3 0x1>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		syscon1: syscon@80000100 {
+			compatible = "cirrus,ep7209-syscon1", "syscon";
+			reg = <0x80000100 0x80>;
+		};
+
+		bus: bus@80000180 {
+			#address-cells = <2>;
+			#size-cells = <1>;
+			compatible = "cirrus,ep7209-bus", "simple-bus";
+			clocks = <&clks CLPS711X_CLK_BUS>;
+			reg = <0x80000180 0x80>;
+			ranges = <
+				0 0 0x00000000 0x10000000
+				1 0 0x10000000 0x10000000
+				2 0 0x20000000 0x10000000
+				3 0 0x30000000 0x10000000
+				4 0 0x40000000 0x10000000
+				5 0 0x50000000 0x10000000
+				6 0 0x60000000 0x0000c000
+				7 0 0x70000000 0x00000080
+			>;
+		};
+
+		fb: fb@800002c0 {
+			compatible = "cirrus,ep7209-fb";
+			reg = <0x800002c0 0xd44>, <0x60000000 0xc000>;
+			clocks = <&clks CLPS711X_CLK_BUS>;
+			syscon = <&syscon1>;
+			status = "disabled";
+		};
+
+		timer1: timer@80000300 {
+			compatible = "cirrus,ep7209-timer";
+			reg = <0x80000300 0x4>;
+			clocks = <&clks CLPS711X_CLK_TIMER1>;
+			interrupts = <8>;
+		};
+
+		timer2: timer@80000340 {
+			compatible = "cirrus,ep7209-timer";
+			reg = <0x80000340 0x4>;
+			clocks = <&clks CLPS711X_CLK_TIMER2>;
+			interrupts = <9>;
+		};
+
+		pwm: pwm@80000400 {
+			compatible = "cirrus,ep7209-pwm";
+			reg = <0x80000400 0x4>;
+			clocks = <&clks CLPS711X_CLK_PWM>;
+			#pwm-cells = <1>;
+		};
+
+		uart1: serial@80000480 {
+			compatible = "cirrus,ep7209-uart";
+			reg = <0x80000480 0x80>;
+			interrupts = <12 13>;
+			clocks = <&clks CLPS711X_CLK_UART>;
+			syscon = <&syscon1>;
+		};
+
+		spi: spi@80000500 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cirrus,ep7209-spi";
+			reg = <0x80000500 0x4>;
+			interrupts = <15>;
+			clocks = <&clks CLPS711X_CLK_SPI>;
+			syscon = <&syscon3>;
+			status = "disabled";
+		};
+
+		syscon2: syscon@80001100 {
+			compatible = "cirrus,ep7209-syscon2", "syscon";
+			reg = <0x80001100 0x80>;
+		};
+
+		uart2: serial@80001480 {
+			compatible = "cirrus,ep7209-uart";
+			reg = <0x80001480 0x80>;
+			interrupts = <28 29>;
+			clocks = <&clks CLPS711X_CLK_UART>;
+			syscon = <&syscon2>;
+		};
+
+		dai: dai@80002000 {
+			#sound-dai-cells = <0>;
+			compatible = "cirrus,ep7209-dai";
+			reg = <0x80002000 0x604>;
+			clocks = <&clks CLPS711X_CLK_PLL>;
+			clock-names = "pll";
+			interrupts = <32>;
+			syscon = <&syscon3>;
+			status = "disabled";
+		};
+
+		syscon3: syscon@80002200 {
+			compatible = "cirrus,ep7209-syscon3", "syscon";
+			reg = <0x80002200 0x40>;
+		};
+	};
+
+	keypad: keypad {
+		compatible = "cirrus,ep7209-keypad";
+		interrupt-parent = <&intc>;
+		interrupts = <16>;
+		syscon = <&syscon1>;
+		status = "disabled";
+	};
+
+	mctrl: mctrl {
+		compatible = "cirrus,ep7209-mctrl-gpio";
+		gpio,syscon-dev = <&syscon1 0 0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};

linux-7.2.3/arch/arm/boot/dts/cirrus/ep7211-edb7211.dts

@@ -0,0 +1,97 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "ep7211.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Cirrus Logic EP7211 Development Board";
+	compatible = "cirrus,edb7211", "cirrus,ep7211", "cirrus,ep7209";
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x02000000>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0>;
+		brightness-levels = <
+			0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7
+			0x8 0x9 0xa 0xb 0xc 0xd 0xe 0xf
+		>;
+		default-brightness-level = <0x0>;
+		power-supply = <&blen>;
+	};
+
+	display: display {
+		model = "320x240x4";
+		bits-per-pixel = <4>;
+		ac-prescale = <17>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing-320x240 {
+				hactive = <320>;
+				hback-porch = <0>;
+				hfront-porch = <0>;
+				hsync-len = <0>;
+				vactive = <240>;
+				vback-porch = <0>;
+				vfront-porch = <0>;
+				vsync-len = <0>;
+				clock-frequency = <6500000>;
+			};
+		};
+	};
+
+	i2c: i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&portd 4 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&portd 5 GPIO_ACTIVE_HIGH>;
+		i2c-gpio,delay-us = <2>;
+		i2c-gpio,scl-output-only;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	lcddc: lcddc {
+		compatible = "regulator-fixed";
+		regulator-name = "BACKLIGHT ENABLE";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&portd 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	blen: blen {
+		compatible = "regulator-fixed";
+		regulator-name = "BACKLIGHT ENABLE";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&portd 3 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&bus {
+	flash: nor@0 {
+		compatible = "cfi-flash";
+		reg = <0 0x00000000 0x02000000>;
+		bank-width = <2>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&fb {
+	display = <&display>;
+	lcd-supply = <&lcddc>;
+	status = "okay";
+};
+
+&portd {
+	lcden-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "LCD ENABLE";
+	};
+};

linux-7.2.3/arch/arm/boot/dts/cirrus/ep7211.dtsi

@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "ep7209.dtsi"
+
+/ {
+	model = "Cirrus Logic EP7211";
+	compatible = "cirrus,ep7211", "cirrus,ep7209";
+};

linux-7.2.3/arch/arm/boot/dts/cirrus/ep93xx-bk3.dts

@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Liebherr controller BK3.1 based on Cirrus EP9302 SoC
+ */
+/dts-v1/;
+#include "ep93xx.dtsi"
+
+/ {
+	model = "Liebherr controller BK3.1";
+	compatible = "liebherr,bk3", "cirrus,ep9301";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	chosen {
+	};
+
+	memory@0 {
+		device_type = "memory";
+		/* should be set from ATAGS */
+		reg = <0x00000000 0x02000000>,
+		      <0x000530c0 0x01fdd000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			label = "grled";
+			gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+		};
+
+		led-1 {
+			label = "rdled";
+			gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_FAULT;
+		};
+	};
+};
+
+&ebi {
+	nand-controller@60000000 {
+		compatible = "technologic,ts7200-nand";
+		reg = <0x60000000 0x8000000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		nand@0 {
+			reg = <0>;
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "System";
+					reg = <0x00000000 0x01e00000>;
+					read-only;
+				};
+
+				partition@1e00000 {
+					label = "Data";
+					reg = <0x01e00000 0x05f20000>;
+				};
+
+				partition@7d20000 {
+					label = "RedBoot";
+					reg = <0x07d20000 0x002e0000>;
+					read-only;
+				};
+			};
+		};
+	};
+};
+
+&eth0 {
+	phy-handle = <&phy0>;
+};
+
+&i2s {
+	dmas = <&dma0 0 1>, <&dma0 0 2>;
+	dma-names = "tx", "rx";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_on_ac97_pins>;
+	status = "okay";
+};
+
+&gpio1 {
+	/* PWM */
+	gpio-ranges = <&syscon 6 163 1>;
+};
+
+&gpio4 {
+	gpio-ranges = <&syscon 0 97 2>;
+	status = "okay";
+};
+
+&gpio6 {
+	gpio-ranges = <&syscon 0 87 2>;
+	status = "okay";
+};
+
+&gpio7 {
+	gpio-ranges = <&syscon 2 199 4>;
+	status = "okay";
+};
+
+&mdio0 {
+	phy0: ethernet-phy@1 {
+		reg = <1>;
+		device_type = "ethernet-phy";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};

linux-7.2.3/arch/arm/boot/dts/cirrus/ep93xx-edb9302.dts

@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+/*
+ * Device Tree file for Cirrus Logic EDB9302 board based on EP9302 SoC
+ */
+/dts-v1/;
+#include "ep93xx.dtsi"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "cirrus,edb9302", "cirrus,ep9301";
+	model = "cirrus,edb9302";
+
+	chosen {
+	};
+
+	memory@0 {
+		device_type = "memory";
+		/* should be set from ATAGS */
+		reg = <0x0000000 0x800000>,
+		      <0x1000000 0x800000>,
+		      <0x4000000 0x800000>,
+		      <0x5000000 0x800000>;
+	};
+
+	sound {
+		compatible = "audio-graph-card2";
+		label = "EDB93XX";
+		links = <&i2s_port>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			label = "grled";
+			gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+		};
+
+		led-1 {
+			label = "rdled";
+			gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_FAULT;
+		};
+	};
+};
+
+&adc {
+	status = "okay";
+};
+
+&ebi {
+	flash@60000000 {
+		compatible = "cfi-flash";
+		reg = <0x60000000 0x1000000>;
+		bank-width = <2>;
+	};
+};
+
+&eth0 {
+	phy-handle = <&phy0>;
+};
+
+&gpio0 {
+	gpio-ranges = <&syscon 0 153 1>,
+		      <&syscon 1 152 1>,
+		      <&syscon 2 151 1>,
+		      <&syscon 3 148 1>,
+		      <&syscon 4 147 1>,
+		      <&syscon 5 146 1>,
+		      <&syscon 6 145 1>,
+		      <&syscon 7 144 1>;
+};
+
+&gpio1 {
+	gpio-ranges = <&syscon 0 143 1>,
+		      <&syscon 1 142 1>,
+		      <&syscon 2 141 1>,
+		      <&syscon 3 140 1>,
+		      <&syscon 4 165 1>,
+		      <&syscon 5 164 1>,
+		      <&syscon 6 163 1>,
+		      <&syscon 7 160 1>;
+};
+
+&gpio2 {
+	gpio-ranges = <&syscon 0 115 1>;
+};
+
+/* edb9302 doesn't have GPIO Port D present */
+&gpio3 {
+	status = "disabled";
+};
+
+&gpio4 {
+	gpio-ranges = <&syscon 0 97 2>;
+};
+
+&gpio5 {
+	gpio-ranges = <&syscon 1 170 1>,
+		      <&syscon 2 169 1>,
+		      <&syscon 3 168 1>;
+};
+
+&gpio6 {
+	gpio-ranges = <&syscon 0 87 2>;
+};
+
+&gpio7 {
+	gpio-ranges = <&syscon 2 199 4>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_on_ac97_pins>;
+	status = "okay";
+	i2s_port: port {
+		i2s_ep: endpoint {
+			system-clock-direction-out;
+			frame-master;
+			bitclock-master;
+			mclk-fs = <256>;
+			dai-format = "i2s";
+			convert-channels = <2>;
+			convert-sample-format = "s32_le";
+			remote-endpoint = <&codec_ep>;
+		};
+	};
+};
+
+&mdio0 {
+	phy0: ethernet-phy@1 {
+		reg = <1>;
+		device_type = "ethernet-phy";
+	};
+};
+
+&spi0 {
+	cs-gpios = <&gpio0 6 GPIO_ACTIVE_LOW
+		    &gpio0 7 GPIO_ACTIVE_LOW>;
+	dmas = <&dma1 10 2>, <&dma1 10 1>;
+	dma-names = "rx", "tx";
+	status = "okay";
+
+	cs4271: codec@0 {
+		compatible = "cirrus,cs4271";
+		reg = <0>;
+		#sound-dai-cells = <0>;
+		spi-max-frequency = <6000000>;
+		spi-cpol;
+		spi-cpha;
+		reset-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+		port {
+			codec_ep: endpoint {
+				remote-endpoint = <&i2s_ep>;
+			};
+		};
+	};
+
+	at25f1024: eeprom@1 {
+		compatible = "atmel,at25";
+		reg = <1>;
+		address-width = <8>;
+		size = <0x20000>;
+		pagesize = <256>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};

linux-7.2.3/arch/arm/boot/dts/cirrus/ep93xx-ts7250.dts

@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Technologic Systems ts7250 board based on Cirrus EP9302 SoC
+ */
+/dts-v1/;
+#include "ep93xx.dtsi"
+
+/ {
+	compatible = "technologic,ts7250", "cirrus,ep9301";
+	model = "TS-7250 SBC";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	chosen {
+	};
+
+	memory@0 {
+		device_type = "memory";
+		/* should be set from ATAGS */
+		reg = <0x00000000 0x02000000>,
+		      <0x000530c0 0x01fdd000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			label = "grled";
+			gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+		};
+
+		led-1 {
+			label = "rdled";
+			gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_FAULT;
+		};
+	};
+};
+
+&ebi {
+	nand-controller@60000000 {
+		compatible = "technologic,ts7200-nand";
+		reg = <0x60000000 0x8000000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		nand@0 {
+			reg = <0>;
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "TS-BOOTROM";
+					reg = <0x00000000 0x00020000>;
+					read-only;
+				};
+
+				partition@20000 {
+					label = "Linux";
+					reg = <0x00020000 0x07d00000>;
+				};
+
+				partition@7d20000 {
+					label = "RedBoot";
+					reg = <0x07d20000 0x002e0000>;
+					read-only;
+				};
+			};
+		};
+	};
+
+	rtc@10800000 {
+		compatible = "st,m48t86";
+		reg = <0x10800000 0x1>,
+			<0x11700000 0x1>;
+	};
+
+	watchdog@23800000 {
+		compatible = "technologic,ts7200-wdt";
+		reg = <0x23800000 0x01>,
+			<0x23c00000 0x01>;
+		timeout-sec = <30>;
+	};
+};
+
+&eth0 {
+	phy-handle = <&phy0>;
+};
+
+&gpio1 {
+	/* PWM */
+	gpio-ranges = <&syscon 6 163 1>;
+};
+
+/* ts7250 doesn't have GPIO Port D present */
+&gpio3 {
+	status = "disabled";
+};
+
+&gpio4 {
+	gpio-ranges = <&syscon 0 97 2>;
+};
+
+&gpio6 {
+	gpio-ranges = <&syscon 0 87 2>;
+};
+
+&gpio7 {
+	gpio-ranges = <&syscon 2 199 4>;
+};
+
+&spi0 {
+	cs-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+	dmas = <&dma1 10 2>, <&dma1 10 1>;
+	dma-names = "rx", "tx";
+	status = "okay";
+
+	tmp122: temperature-sensor@0 {
+		compatible = "ti,tmp122";
+		reg = <0>;
+		spi-max-frequency = <2000000>;
+	};
+};
+
+&mdio0 {
+	phy0: ethernet-phy@1 {
+		reg = <1>;
+		device_type = "ethernet-phy";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};

linux-7.2.3/arch/arm/boot/dts/cirrus/ep93xx.dtsi

@@ -0,0 +1,444 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Cirrus Logic systems EP93XX SoC
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/clock/cirrus,ep9301-syscon.h>
+/ {
+	soc: soc {
+		compatible = "simple-bus";
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		syscon: syscon@80930000 {
+			compatible = "cirrus,ep9301-syscon", "syscon";
+			reg = <0x80930000 0x1000>;
+
+			#clock-cells = <1>;
+			clocks = <&xtali>;
+
+			spi_default_pins: pins-spi {
+				function = "spi";
+				groups = "ssp";
+			};
+
+			ac97_default_pins: pins-ac97 {
+				function = "ac97";
+				groups = "ac97";
+			};
+
+			i2s_on_ssp_pins: pins-i2sonssp {
+				function = "i2s";
+				groups = "i2s_on_ssp";
+			};
+
+			i2s_on_ac97_pins: pins-i2sonac97 {
+				function = "i2s";
+				groups = "i2s_on_ac97";
+			};
+
+			gpio1_default_pins: pins-gpio1 {
+				function = "gpio";
+				groups = "gpio1agrp";
+			};
+
+			pwm1_default_pins: pins-pwm1 {
+				function = "pwm";
+				groups = "pwm1";
+			};
+
+			gpio2_default_pins: pins-gpio2 {
+				function = "gpio";
+				groups = "gpio2agrp";
+			};
+
+			gpio3_default_pins: pins-gpio3 {
+				function = "gpio";
+				groups = "gpio3agrp";
+			};
+
+			keypad_default_pins: pins-keypad {
+				function = "keypad";
+				groups = "keypadgrp";
+			};
+
+			gpio4_default_pins: pins-gpio4 {
+				function = "gpio";
+				groups = "gpio4agrp";
+			};
+
+			gpio6_default_pins: pins-gpio6 {
+				function = "gpio";
+				groups = "gpio6agrp";
+			};
+
+			gpio7_default_pins: pins-gpio7 {
+				function = "gpio";
+				groups = "gpio7agrp";
+			};
+
+			ide_default_pins: pins-ide {
+				function = "pata";
+				groups = "idegrp";
+			};
+
+			lcd_on_dram0_pins: pins-rasteronsdram0 {
+				function = "lcd";
+				groups = "rasteronsdram0grp";
+			};
+
+			lcd_on_dram3_pins: pins-rasteronsdram3 {
+				function = "lcd";
+				groups = "rasteronsdram3grp";
+			};
+		};
+
+		adc: adc@80900000 {
+			compatible = "cirrus,ep9301-adc";
+			reg = <0x80900000 0x28>;
+			clocks = <&syscon EP93XX_CLK_ADC>;
+			interrupt-parent = <&vic0>;
+			interrupts = <30>;
+			status = "disabled";
+		};
+
+		/*
+		 * The EP93XX expansion bus is a set of up to 7 each up to 16MB
+		 * windows in the 256MB space from 0x50000000 to 0x5fffffff.
+		 * But since we don't require to setup it in any way, we can
+		 * represent it as a simple-bus.
+		 */
+		ebi: bus@80080000 {
+			compatible = "simple-bus";
+			reg = <0x80080000 0x20>;
+			native-endian;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+		};
+
+		dma0: dma-controller@80000000 {
+			compatible = "cirrus,ep9301-dma-m2p";
+			reg = <0x80000000 0x0040>,
+			      <0x80000040 0x0040>,
+			      <0x80000080 0x0040>,
+			      <0x800000c0 0x0040>,
+			      <0x80000240 0x0040>,
+			      <0x80000200 0x0040>,
+			      <0x800002c0 0x0040>,
+			      <0x80000280 0x0040>,
+			      <0x80000340 0x0040>,
+			      <0x80000300 0x0040>;
+			clocks = <&syscon EP93XX_CLK_M2P0>,
+				 <&syscon EP93XX_CLK_M2P1>,
+				 <&syscon EP93XX_CLK_M2P2>,
+				 <&syscon EP93XX_CLK_M2P3>,
+				 <&syscon EP93XX_CLK_M2P4>,
+				 <&syscon EP93XX_CLK_M2P5>,
+				 <&syscon EP93XX_CLK_M2P6>,
+				 <&syscon EP93XX_CLK_M2P7>,
+				 <&syscon EP93XX_CLK_M2P8>,
+				 <&syscon EP93XX_CLK_M2P9>;
+			clock-names = "m2p0", "m2p1",
+				      "m2p2", "m2p3",
+				      "m2p4", "m2p5",
+				      "m2p6", "m2p7",
+				      "m2p8", "m2p9";
+			interrupt-parent = <&vic0>;
+			interrupts = <7>, <8>, <9>, <10>, <11>,
+				<12>, <13>, <14>, <15>, <16>;
+			#dma-cells = <2>;
+		};
+
+		dma1: dma-controller@80000100 {
+			compatible = "cirrus,ep9301-dma-m2m";
+			reg = <0x80000100 0x0040>,
+			      <0x80000140 0x0040>;
+			clocks = <&syscon EP93XX_CLK_M2M0>,
+				 <&syscon EP93XX_CLK_M2M1>;
+			clock-names = "m2m0", "m2m1";
+			interrupt-parent = <&vic0>;
+			interrupts = <17>, <18>;
+			#dma-cells = <2>;
+		};
+
+		eth0: ethernet@80010000 {
+			compatible = "cirrus,ep9301-eth";
+			reg = <0x80010000 0x10000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <7>;
+			mdio0: mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		gpio0: gpio@80840000 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840000 0x04>,
+			      <0x80840010 0x04>,
+			      <0x80840090 0x1c>;
+			reg-names = "data", "dir", "intr";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&vic1>;
+			interrupts = <27>;
+		};
+
+		gpio1: gpio@80840004 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840004 0x04>,
+			      <0x80840014 0x04>,
+			      <0x808400ac 0x1c>;
+			reg-names = "data", "dir", "intr";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&vic1>;
+			interrupts = <27>;
+		};
+
+		gpio2: gpio@80840008 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840008 0x04>,
+			      <0x80840018 0x04>;
+			reg-names = "data", "dir";
+			gpio-controller;
+			#gpio-cells = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio2_default_pins>;
+		};
+
+		gpio3: gpio@8084000c {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x8084000c 0x04>,
+			      <0x8084001c 0x04>;
+			reg-names = "data", "dir";
+			gpio-controller;
+			#gpio-cells = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio3_default_pins>;
+		};
+
+		gpio4: gpio@80840020 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840020 0x04>,
+			      <0x80840024 0x04>;
+			reg-names = "data", "dir";
+			gpio-controller;
+			#gpio-cells = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio4_default_pins>;
+		};
+
+		gpio5: gpio@80840030 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840030 0x04>,
+			      <0x80840034 0x04>,
+			      <0x8084004c 0x1c>;
+			reg-names = "data", "dir", "intr";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts-extended = <&vic0 19>, <&vic0 20>,
+					      <&vic0 21>, <&vic0 22>,
+					      <&vic1 15>, <&vic1 16>,
+					      <&vic1 17>, <&vic1 18>;
+		};
+
+		gpio6: gpio@80840038 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840038 0x04>,
+			      <0x8084003c 0x04>;
+			reg-names = "data", "dir";
+			gpio-controller;
+			#gpio-cells = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio6_default_pins>;
+		};
+
+		gpio7: gpio@80840040 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840040 0x04>,
+			      <0x80840044 0x04>;
+			reg-names = "data", "dir";
+			gpio-controller;
+			#gpio-cells = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio7_default_pins>;
+		};
+
+		i2s: i2s@80820000 {
+			compatible = "cirrus,ep9301-i2s";
+			reg = <0x80820000 0x100>;
+			#sound-dai-cells = <0>;
+			interrupt-parent = <&vic1>;
+			interrupts = <28>;
+			clocks = <&syscon EP93XX_CLK_I2S_MCLK>,
+				 <&syscon EP93XX_CLK_I2S_SCLK>,
+				 <&syscon EP93XX_CLK_I2S_LRCLK>;
+			clock-names = "mclk", "sclk", "lrclk";
+			dmas = <&dma0 0 1>, <&dma0 0 2>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		ide: ide@800a0000 {
+			compatible = "cirrus,ep9312-pata";
+			reg = <0x800a0000 0x38>;
+			interrupt-parent = <&vic1>;
+			interrupts = <8>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&ide_default_pins>;
+			status = "disabled";
+		};
+
+		vic0: interrupt-controller@800b0000 {
+			compatible = "arm,pl192-vic";
+			reg = <0x800b0000 0x1000>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			valid-mask = <0x7ffffffc>;
+			valid-wakeup-mask = <0x0>;
+		};
+
+		vic1: interrupt-controller@800c0000 {
+			compatible = "arm,pl192-vic";
+			reg = <0x800c0000 0x1000>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			valid-mask = <0x1fffffff>;
+			valid-wakeup-mask = <0x0>;
+		};
+
+		keypad: keypad@800f0000 {
+			compatible = "cirrus,ep9307-keypad";
+			reg = <0x800f0000 0x0c>;
+			interrupt-parent = <&vic0>;
+			interrupts = <29>;
+			clocks = <&syscon EP93XX_CLK_KEYPAD>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&keypad_default_pins>;
+			linux,keymap =	<KEY_UP>,
+					<KEY_DOWN>,
+					<KEY_VOLUMEDOWN>,
+					<KEY_HOME>,
+					<KEY_RIGHT>,
+					<KEY_LEFT>,
+					<KEY_ENTER>,
+					<KEY_VOLUMEUP>,
+					<KEY_F6>,
+					<KEY_F8>,
+					<KEY_F9>,
+					<KEY_F10>,
+					<KEY_F1>,
+					<KEY_F2>,
+					<KEY_F3>,
+					<KEY_POWER>;
+		};
+
+		pwm0: pwm@80910000 {
+			compatible = "cirrus,ep9301-pwm";
+			reg = <0x80910000 0x10>;
+			clocks = <&syscon EP93XX_CLK_PWM>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		pwm1: pwm@80910020 {
+			compatible = "cirrus,ep9301-pwm";
+			reg = <0x80910020 0x10>;
+			clocks = <&syscon EP93XX_CLK_PWM>;
+			#pwm-cells = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pwm1_default_pins>;
+			status = "disabled";
+		};
+
+		rtc0: rtc@80920000 {
+			compatible = "cirrus,ep9301-rtc";
+			reg = <0x80920000 0x100>;
+		};
+
+		spi0: spi@808a0000 {
+			compatible = "cirrus,ep9301-spi";
+			reg = <0x808a0000 0x18>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupt-parent = <&vic1>;
+			interrupts = <21>;
+			clocks = <&syscon EP93XX_CLK_SPI>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi_default_pins>;
+			status = "disabled";
+		};
+
+		timer: timer@80810000 {
+			compatible = "cirrus,ep9301-timer";
+			reg = <0x80810000 0x100>;
+			interrupt-parent = <&vic1>;
+			interrupts = <19>;
+		};
+
+		uart0: serial@808c0000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x808c0000 0x1000>;
+			arm,primecell-periphid = <0x00041010>;
+			clocks = <&syscon EP93XX_CLK_UART1>, <&syscon EP93XX_CLK_UART>;
+			clock-names = "uartclk", "apb_pclk";
+			interrupt-parent = <&vic1>;
+			interrupts = <20>;
+			status = "disabled";
+		};
+
+		uart1: uart@808d0000 {
+			compatible = "arm,primecell";
+			reg = <0x808d0000 0x1000>;
+			arm,primecell-periphid = <0x00041010>;
+			clocks = <&syscon EP93XX_CLK_UART2>, <&syscon EP93XX_CLK_UART>;
+			clock-names = "apb:uart2", "apb_pclk";
+			interrupt-parent = <&vic1>;
+			interrupts = <22>;
+			status = "disabled";
+		};
+
+		uart2: uart@808b0000 {
+			compatible = "arm,primecell";
+			reg = <0x808b0000 0x1000>;
+			arm,primecell-periphid = <0x00041010>;
+			clocks = <&syscon EP93XX_CLK_UART3>, <&syscon EP93XX_CLK_UART>;
+			clock-names = "apb:uart3", "apb_pclk";
+			interrupt-parent = <&vic1>;
+			interrupts = <23>;
+			status = "disabled";
+		};
+
+		usb0: usb@80020000 {
+			compatible = "generic-ohci";
+			reg = <0x80020000 0x10000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <24>;
+			clocks = <&syscon EP93XX_CLK_USB>;
+			status = "disabled";
+		};
+
+		watchdog0: watchdog@80940000 {
+			compatible = "cirrus,ep9301-wdt";
+			reg = <0x80940000 0x08>;
+		};
+	};
+
+	xtali: oscillator {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <14745600>;
+		clock-output-names = "xtali";
+	};
+};