Resguardo inicial

linux-7.2.3/arch/arm/boot/dts/nxp/lpc/Makefile

@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_LPC18XX) += \
+	lpc4337-ciaa.dtb \
+	lpc4350-hitex-eval.dtb \
+	lpc4357-ea4357-devkit.dtb \
+	lpc4357-myd-lpc4357.dtb
+dtb-$(CONFIG_ARCH_LPC32XX) += \
+	lpc3250-ea3250.dtb \
+	lpc3250-phy3250.dtb

linux-7.2.3/arch/arm/boot/dts/nxp/lpc/lpc18xx.dtsi

@@ -0,0 +1,543 @@
+/*
+ * Common base for NXP LPC18xx and LPC43xx devices.
+ *
+ * Copyright 2015 Joachim Eastwood <manabian@gmail.com>
+ *
+ * This code is released using a dual license strategy: BSD/GPL
+ * You can choose the licence that better fits your requirements.
+ *
+ * Released under the terms of 3-clause BSD License
+ * Released under the terms of GNU General Public License Version 2.0
+ *
+ */
+
+#include "../../armv7-m.dtsi"
+
+#include "dt-bindings/clock/lpc18xx-cgu.h"
+#include "dt-bindings/clock/lpc18xx-ccu.h"
+
+#define LPC_PIN(port, pin)	(0x##port * 32 + pin)
+#define LPC_GPIO(port, pin)	(port * 32 + pin)
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-m3";
+			device_type = "cpu";
+			reg = <0x0>;
+			clocks = <&ccu1 CLK_CPU_CORE>;
+		};
+	};
+
+	clocks {
+		xtal: xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <12000000>;
+		};
+
+		xtal32: xtal32 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+
+		enet_rx_clk: enet_rx_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+			clock-output-names = "enet_rx_clk";
+		};
+
+		enet_tx_clk: enet_tx_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+			clock-output-names = "enet_tx_clk";
+		};
+
+		gp_clkin: gp_clkin {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+			clock-output-names = "gp_clkin";
+		};
+	};
+
+	soc {
+		sct_pwm: pwm@40000000 {
+			compatible = "nxp,lpc1850-sct-pwm";
+			reg = <0x40000000 0x1000>;
+			clocks = <&ccu1 CLK_CPU_SCT>;
+			clock-names = "pwm";
+			resets = <&rgu 37>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		dmac: dma-controller@40002000 {
+			compatible = "arm,pl080", "arm,primecell";
+			arm,primecell-periphid = <0x00041080>;
+			reg = <0x40002000 0x1000>;
+			interrupts = <2>;
+			clocks = <&ccu1 CLK_CPU_DMA>;
+			clock-names = "apb_pclk";
+			resets = <&rgu 19>;
+			#dma-cells = <2>;
+			dma-channels = <8>;
+			dma-requests = <16>;
+			lli-bus-interface-ahb1;
+			lli-bus-interface-ahb2;
+			mem-bus-interface-ahb1;
+			mem-bus-interface-ahb2;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+		};
+
+		spifi: spi@40003000 {
+			compatible = "nxp,lpc1773-spifi";
+			reg = <0x40003000 0x1000>, <0x14000000 0x4000000>;
+			reg-names = "spifi", "flash";
+			interrupts = <30>;
+			clocks = <&ccu1 CLK_SPIFI>, <&ccu1 CLK_CPU_SPIFI>;
+			clock-names = "spifi", "reg";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			resets = <&rgu 53>;
+			status = "disabled";
+		};
+
+		mmcsd: mmc@40004000 {
+			compatible = "snps,dw-mshc";
+			reg = <0x40004000 0x1000>;
+			interrupts = <6>;
+			clocks = <&ccu1 CLK_CPU_SDIO>, <&ccu2 CLK_SDIO>;
+			clock-names = "biu", "ciu";
+			resets = <&rgu 20>;
+			status = "disabled";
+		};
+
+		usb0: usb@40006100 {
+			compatible = "nxp,lpc1850-ehci", "generic-ehci";
+			reg = <0x40006100 0x100>;
+			interrupts = <8>;
+			clocks = <&ccu1 CLK_CPU_USB0>;
+			resets = <&rgu 17>;
+			phys = <&usb0_otg_phy>;
+			phy-names = "usb";
+			has-transaction-translator;
+			status = "disabled";
+		};
+
+		usb1: usb@40007100 {
+			compatible = "nxp,lpc1850-ehci", "generic-ehci";
+			reg = <0x40007100 0x100>;
+			interrupts = <9>;
+			clocks = <&ccu1 CLK_CPU_USB1>;
+			resets = <&rgu 18>;
+			status = "disabled";
+		};
+
+		emc: memory-controller@40005000 {
+			compatible = "arm,pl172", "arm,primecell";
+			reg = <0x40005000 0x1000>;
+			clocks = <&ccu1 CLK_CPU_EMCDIV>, <&ccu1 CLK_CPU_EMC>;
+			clock-names = "mpmcclk", "apb_pclk";
+			resets = <&rgu 21>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <0 0 0x1c000000 0x1000000
+				  1 0 0x1d000000 0x1000000
+				  2 0 0x1e000000 0x1000000
+				  3 0 0x1f000000 0x1000000>;
+			status = "disabled";
+		};
+
+		lcdc: lcd-controller@40008000 {
+			compatible = "arm,pl111", "arm,primecell";
+			reg = <0x40008000 0x1000>;
+			interrupts = <7>;
+			interrupt-names = "combined";
+			clocks = <&cgu BASE_LCD_CLK>, <&ccu1 CLK_CPU_LCD>;
+			clock-names = "clcdclk", "apb_pclk";
+			resets = <&rgu 16>;
+			status = "disabled";
+		};
+
+		eeprom: eeprom@4000e000 {
+			compatible = "nxp,lpc1857-eeprom";
+			reg = <0x4000e000 0x1000>, <0x20040000 0x4000>;
+			reg-names = "reg", "mem";
+			clocks = <&ccu1 CLK_CPU_EEPROM>;
+			clock-names = "eeprom";
+			resets = <&rgu 27>;
+			interrupts = <4>;
+			status = "disabled";
+		};
+
+		mac: ethernet@40010000 {
+			compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac";
+			reg = <0x40010000 0x2000>;
+			interrupts = <5>;
+			interrupt-names = "macirq";
+			clocks = <&ccu1 CLK_CPU_ETHERNET>;
+			clock-names = "stmmaceth";
+			resets = <&rgu 22>;
+			reset-names = "stmmaceth";
+			rx-fifo-depth = <256>;
+			tx-fifo-depth = <256>;
+			snps,pbl = <4>; /* 32 (8x mode) */
+			snps,force_thresh_dma_mode;
+			status = "disabled";
+		};
+
+		creg: syscon@40043000 {
+			compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd";
+			reg = <0x40043000 0x1000>;
+			clocks = <&ccu1 CLK_CPU_CREG>;
+			resets = <&rgu 5>;
+
+			creg_clk: clock-controller {
+				compatible = "nxp,lpc1850-creg-clk";
+				clocks = <&xtal32>;
+				#clock-cells = <1>;
+			};
+
+			usb0_otg_phy: phy {
+				compatible = "nxp,lpc1850-usb-otg-phy";
+				clocks = <&ccu1 CLK_USB0>;
+				#phy-cells = <0>;
+			};
+
+			dmamux: dma-mux {
+				compatible = "nxp,lpc1850-dmamux";
+				#dma-cells = <3>;
+				dma-requests = <64>;
+				dma-masters = <&dmac>;
+			};
+		};
+
+		rtc: rtc@40046000 {
+			compatible = "nxp,lpc1850-rtc", "nxp,lpc1788-rtc";
+			reg = <0x40046000 0x1000>;
+			interrupts = <47>;
+			clocks = <&creg_clk 0>, <&ccu1 CLK_CPU_BUS>;
+			clock-names = "rtc", "reg";
+		};
+
+		cgu: clock-controller@40050000 {
+			compatible = "nxp,lpc1850-cgu";
+			reg = <0x40050000 0x1000>;
+			#clock-cells = <1>;
+			clocks = <&xtal>, <&creg_clk 1>, <&enet_rx_clk>, <&enet_tx_clk>, <&gp_clkin>;
+		};
+
+		ccu1: clock-controller@40051000 {
+			compatible = "nxp,lpc1850-ccu";
+			reg = <0x40051000 0x1000>;
+			#clock-cells = <1>;
+			clocks = <&cgu BASE_APB3_CLK>,   <&cgu BASE_APB1_CLK>,
+				 <&cgu BASE_SPIFI_CLK>,  <&cgu BASE_CPU_CLK>,
+				 <&cgu BASE_PERIPH_CLK>, <&cgu BASE_USB0_CLK>,
+				 <&cgu BASE_USB1_CLK>,   <&cgu BASE_SPI_CLK>;
+			clock-names = "base_apb3_clk",   "base_apb1_clk",
+				      "base_spifi_clk",  "base_cpu_clk",
+				      "base_periph_clk", "base_usb0_clk",
+				      "base_usb1_clk",   "base_spi_clk";
+		};
+
+		ccu2: clock-controller@40052000 {
+			compatible = "nxp,lpc1850-ccu";
+			reg = <0x40052000 0x1000>;
+			#clock-cells = <1>;
+			clocks = <&cgu BASE_AUDIO_CLK>, <&cgu BASE_UART3_CLK>,
+				 <&cgu BASE_UART2_CLK>, <&cgu BASE_UART1_CLK>,
+				 <&cgu BASE_UART0_CLK>, <&cgu BASE_SSP1_CLK>,
+				 <&cgu BASE_SSP0_CLK>,  <&cgu BASE_SDIO_CLK>;
+			clock-names = "base_audio_clk", "base_uart3_clk",
+				      "base_uart2_clk", "base_uart1_clk",
+				      "base_uart0_clk", "base_ssp1_clk",
+				      "base_ssp0_clk",  "base_sdio_clk";
+		};
+
+		rgu: reset-controller@40053000 {
+			compatible = "nxp,lpc1850-rgu";
+			reg = <0x40053000 0x1000>;
+			clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_BUS>;
+			clock-names = "delay", "reg";
+			#reset-cells = <1>;
+		};
+
+		watchdog@40080000 {
+			compatible = "nxp,lpc1850-wwdt";
+			reg = <0x40080000 0x24>;
+			interrupts = <49>;
+			clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_WWDT>;
+			clock-names = "wdtclk", "reg";
+		};
+
+		uart0: serial@40081000 {
+			compatible = "nxp,lpc1850-uart", "ns16550a";
+			reg = <0x40081000 0x1000>;
+			reg-shift = <2>;
+			interrupts = <24>;
+			clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>;
+			clock-names = "uartclk", "reg";
+			resets = <&rgu 44>;
+			dmas = <&dmamux  1 1 2
+				&dmamux  2 1 2
+				&dmamux 11 2 2
+				&dmamux 12 2 2>;
+			dma-names = "tx", "rx", "tx", "rx";
+			status = "disabled";
+		};
+
+		uart1: serial@40082000 {
+			compatible = "nxp,lpc1850-uart", "ns16550a";
+			reg = <0x40082000 0x1000>;
+			reg-shift = <2>;
+			interrupts = <25>;
+			clocks = <&ccu2 CLK_APB0_UART1>, <&ccu1 CLK_CPU_UART1>;
+			clock-names = "uartclk", "reg";
+			resets = <&rgu 45>;
+			dmas = <&dmamux 3 1 2
+				&dmamux 4 1 2>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		ssp0: spi@40083000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x40083000 0x1000>;
+			interrupts = <22>;
+			clocks = <&ccu2 CLK_APB0_SSP0>, <&ccu1 CLK_CPU_SSP0>;
+			clock-names = "sspclk", "apb_pclk";
+			resets = <&rgu 50>;
+			dmas = <&dmamux  9 0 2
+				&dmamux 10 0 2>;
+			dma-names = "rx", "tx";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		timer0: timer@40084000 {
+			compatible = "nxp,lpc3220-timer";
+			reg = <0x40084000 0x1000>;
+			interrupts = <12>;
+			clocks = <&ccu1 CLK_CPU_TIMER0>;
+			clock-names = "timerclk";
+			resets = <&rgu 32>;
+		};
+
+		timer1: timer@40085000 {
+			compatible = "nxp,lpc3220-timer";
+			reg = <0x40085000 0x1000>;
+			interrupts = <13>;
+			clocks = <&ccu1 CLK_CPU_TIMER1>;
+			clock-names = "timerclk";
+			resets = <&rgu 33>;
+		};
+
+		pinctrl: pinctrl@40086000 {
+			compatible = "nxp,lpc1850-scu";
+			reg = <0x40086000 0x1000>;
+			clocks = <&ccu1 CLK_CPU_SCU>;
+		};
+
+		i2c0: i2c@400a1000 {
+			compatible = "nxp,lpc1788-i2c";
+			reg = <0x400a1000 0x1000>;
+			interrupts = <18>;
+			clocks = <&ccu1 CLK_APB1_I2C0>;
+			resets = <&rgu 48>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		can1: can@400a4000 {
+			compatible = "bosch,c_can";
+			reg = <0x400a4000 0x1000>;
+			interrupts = <43>;
+			clocks = <&ccu1 CLK_APB1_CAN1>;
+			resets = <&rgu 54>;
+			status = "disabled";
+		};
+
+		uart2: serial@400c1000 {
+			compatible = "nxp,lpc1850-uart", "ns16550a";
+			reg = <0x400c1000 0x1000>;
+			reg-shift = <2>;
+			interrupts = <26>;
+			clocks = <&ccu2 CLK_APB2_UART2>, <&ccu1 CLK_CPU_UART2>;
+			clock-names = "uartclk", "reg";
+			resets = <&rgu 46>;
+			dmas = <&dmamux 5 1 2
+				&dmamux 6 1 2>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		uart3: serial@400c2000 {
+			compatible = "nxp,lpc1850-uart", "ns16550a";
+			reg = <0x400c2000 0x1000>;
+			reg-shift = <2>;
+			interrupts = <27>;
+			clocks = <&ccu2 CLK_APB2_UART3>, <&ccu1 CLK_CPU_UART3>;
+			clock-names = "uartclk", "reg";
+			resets = <&rgu 47>;
+			dmas = <&dmamux  7 1 2
+				&dmamux  8 1 2
+				&dmamux 13 3 2
+				&dmamux 14 3 2>;
+			dma-names = "tx", "rx", "rx", "tx";
+			status = "disabled";
+		};
+
+		timer2: timer@400c3000 {
+			compatible = "nxp,lpc3220-timer";
+			reg = <0x400c3000 0x1000>;
+			interrupts = <14>;
+			clocks = <&ccu1 CLK_CPU_TIMER2>;
+			clock-names = "timerclk";
+			resets = <&rgu 34>;
+		};
+
+		timer3: timer@400c4000 {
+			compatible = "nxp,lpc3220-timer";
+			reg = <0x400c4000 0x1000>;
+			interrupts = <15>;
+			clocks = <&ccu1 CLK_CPU_TIMER3>;
+			clock-names = "timerclk";
+			resets = <&rgu 35>;
+		};
+
+		ssp1: spi@400c5000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x400c5000 0x1000>;
+			interrupts = <23>;
+			clocks = <&ccu2 CLK_APB2_SSP1>, <&ccu1 CLK_CPU_SSP1>;
+			clock-names = "sspclk", "apb_pclk";
+			resets = <&rgu 51>;
+			dmas = <&dmamux 11 2 2
+				&dmamux 12 2 2
+				&dmamux  3 3 2
+				&dmamux  4 3 2
+				&dmamux  5 2 2
+				&dmamux  6 2 2
+				&dmamux 13 2 2
+				&dmamux 14 2 2>;
+			dma-names = "rx", "tx", "tx", "rx",
+				    "tx", "rx", "rx", "tx";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@400e0000 {
+			compatible = "nxp,lpc1788-i2c";
+			reg = <0x400e0000 0x1000>;
+			interrupts = <19>;
+			clocks = <&ccu1 CLK_APB3_I2C1>;
+			resets = <&rgu 49>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		dac: dac@400e1000 {
+			compatible = "nxp,lpc1850-dac";
+			reg = <0x400e1000 0x1000>;
+			interrupts = <0>;
+			clocks = <&ccu1 CLK_APB3_DAC>;
+			resets = <&rgu 42>;
+			status = "disabled";
+		};
+
+		can0: can@400e2000 {
+			compatible = "bosch,c_can";
+			reg = <0x400e2000 0x1000>;
+			interrupts = <51>;
+			clocks = <&ccu1 CLK_APB3_CAN0>;
+			resets = <&rgu 55>;
+			status = "disabled";
+		};
+
+		adc0: adc@400e3000 {
+			compatible = "nxp,lpc1850-adc";
+			reg = <0x400e3000 0x1000>;
+			interrupts = <17>;
+			clocks = <&ccu1 CLK_APB3_ADC0>;
+			resets = <&rgu 40>;
+			status = "disabled";
+		};
+
+		adc1: adc@400e4000 {
+			compatible = "nxp,lpc1850-adc";
+			reg = <0x400e4000 0x1000>;
+			interrupts = <21>;
+			clocks = <&ccu1 CLK_APB3_ADC1>;
+			resets = <&rgu 41>;
+			status = "disabled";
+		};
+
+		gpio: gpio@400f4000 {
+			compatible = "nxp,lpc1850-gpio";
+			reg = <0x400f4000 0x4000>;
+			clocks = <&ccu1 CLK_CPU_GPIO>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges =	<&pinctrl LPC_GPIO(0,0)  LPC_PIN(0,0)  2>,
+					<&pinctrl LPC_GPIO(0,4)  LPC_PIN(1,0)  1>,
+					<&pinctrl LPC_GPIO(0,8)  LPC_PIN(1,1)  4>,
+					<&pinctrl LPC_GPIO(1,8)  LPC_PIN(1,5)  2>,
+					<&pinctrl LPC_GPIO(1,0)  LPC_PIN(1,7)  8>,
+					<&pinctrl LPC_GPIO(0,2)  LPC_PIN(1,15) 2>,
+					<&pinctrl LPC_GPIO(0,12) LPC_PIN(1,17) 2>,
+					<&pinctrl LPC_GPIO(0,15) LPC_PIN(1,20) 1>,
+					<&pinctrl LPC_GPIO(5,0)  LPC_PIN(2,0)  7>,
+					<&pinctrl LPC_GPIO(0,7)  LPC_PIN(2,7)  1>,
+					<&pinctrl LPC_GPIO(5,7)  LPC_PIN(2,8)  1>,
+					<&pinctrl LPC_GPIO(1,10) LPC_PIN(2,9)  1>,
+					<&pinctrl LPC_GPIO(0,14) LPC_PIN(2,10) 1>,
+					<&pinctrl LPC_GPIO(1,11) LPC_PIN(2,11) 3>,
+					<&pinctrl LPC_GPIO(5,8)  LPC_PIN(3,1)  2>,
+					<&pinctrl LPC_GPIO(1,14) LPC_PIN(3,4)  2>,
+					<&pinctrl LPC_GPIO(0,6)  LPC_PIN(3,6)  1>,
+					<&pinctrl LPC_GPIO(5,10) LPC_PIN(3,7)  2>,
+					<&pinctrl LPC_GPIO(2,0)  LPC_PIN(4,0)  7>,
+					<&pinctrl LPC_GPIO(5,12) LPC_PIN(4,8)  3>,
+					<&pinctrl LPC_GPIO(2,9)  LPC_PIN(5,0)  7>,
+					<&pinctrl LPC_GPIO(2,7)  LPC_PIN(5,7)  1>,
+					<&pinctrl LPC_GPIO(3,0)  LPC_PIN(6,1)  5>,
+					<&pinctrl LPC_GPIO(0,5)  LPC_PIN(6,6)  1>,
+					<&pinctrl LPC_GPIO(5,15) LPC_PIN(6,7)  2>,
+					<&pinctrl LPC_GPIO(3,5)  LPC_PIN(6,9)  3>,
+					<&pinctrl LPC_GPIO(2,8)  LPC_PIN(6,12) 1>,
+					<&pinctrl LPC_GPIO(3,8)  LPC_PIN(7,0)  8>,
+					<&pinctrl LPC_GPIO(4,0)  LPC_PIN(8,0)  8>,
+					<&pinctrl LPC_GPIO(4,12) LPC_PIN(9,0)  4>,
+					<&pinctrl LPC_GPIO(5,17) LPC_PIN(9,4)  2>,
+					<&pinctrl LPC_GPIO(4,11) LPC_PIN(9,6)  1>,
+					<&pinctrl LPC_GPIO(4,8)  LPC_PIN(a,1)  3>,
+					<&pinctrl LPC_GPIO(5,19) LPC_PIN(a,4)  1>,
+					<&pinctrl LPC_GPIO(5,20) LPC_PIN(b,0)  7>,
+					<&pinctrl LPC_GPIO(6,0)  LPC_PIN(c,1) 14>,
+					<&pinctrl LPC_GPIO(6,14) LPC_PIN(d,0) 17>,
+					<&pinctrl LPC_GPIO(7,0)  LPC_PIN(e,0) 16>,
+					<&pinctrl LPC_GPIO(7,16) LPC_PIN(f,1)  3>,
+					<&pinctrl LPC_GPIO(7,19) LPC_PIN(f,5)  7>;
+		};
+	};
+};
+
+&nvic {
+	arm,num-irq-priority-bits = <3>;
+};

linux-7.2.3/arch/arm/boot/dts/nxp/lpc/lpc3250-ea3250.dts

@@ -0,0 +1,273 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Embedded Artists LPC3250 board
+ *
+ * Copyright 2012 Roland Stigge <stigge@antcom.de>
+ */
+
+/dts-v1/;
+#include "lpc32xx.dtsi"
+
+/ {
+	model = "Embedded Artists LPC3250 board based on NXP LPC3250";
+	compatible = "ea,ea3250", "nxp,lpc3250";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x4000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		button {
+			label = "Interrupt Key";
+			linux,code = <103>;
+			gpios = <&gpio 4 1 0>; /* GPI_P3 1 */
+		};
+
+		key-1 {
+			label = "KEY1";
+			linux,code = <1>;
+			gpios = <&pca9532 0 0>;
+		};
+
+		key-2 {
+			label = "KEY2";
+			linux,code = <2>;
+			gpios = <&pca9532 1 0>;
+		};
+
+		key-3 {
+			label = "KEY3";
+			linux,code = <3>;
+			gpios = <&pca9532 2 0>;
+		};
+
+		key-4 {
+			label = "KEY4";
+			linux,code = <4>;
+			gpios = <&pca9532 3 0>;
+		};
+
+		key-joy0 {
+			label = "Joystick Key 0";
+			linux,code = <10>;
+			gpios = <&gpio 2 0 0>; /* P2.0 */
+		};
+
+		key-joy1 {
+			label = "Joystick Key 1";
+			linux,code = <11>;
+			gpios = <&gpio 2 1 0>; /* P2.1 */
+		};
+
+		key-joy2 {
+			label = "Joystick Key 2";
+			linux,code = <12>;
+			gpios = <&gpio 2 2 0>; /* P2.2 */
+		};
+
+		key-joy3 {
+			label = "Joystick Key 3";
+			linux,code = <13>;
+			gpios = <&gpio 2 3 0>; /* P2.3 */
+		};
+
+		key-joy4 {
+			label = "Joystick Key 4";
+			linux,code = <14>;
+			gpios = <&gpio 2 4 0>; /* P2.4 */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* LEDs on OEM Board */
+
+		led1 {
+			gpios = <&gpio 5 14 1>; /* GPO_P3 14, GPIO 93, active low */
+			linux,default-trigger = "timer";
+			default-state = "off";
+		};
+
+		led2 {
+			gpios = <&gpio 2 10 1>; /* P2.10, active low */
+			default-state = "off";
+		};
+
+		led3 {
+			gpios = <&gpio 2 11 1>; /* P2.11, active low */
+			default-state = "off";
+		};
+
+		led4 {
+			gpios = <&gpio 2 12 1>; /* P2.12, active low */
+			default-state = "off";
+		};
+
+		/* LEDs on Base Board */
+
+		lede1 {
+			gpios = <&pca9532 8 0>;
+			default-state = "off";
+		};
+		lede2 {
+			gpios = <&pca9532 9 0>;
+			default-state = "off";
+		};
+		lede3 {
+			gpios = <&pca9532 10 0>;
+			default-state = "off";
+		};
+		lede4 {
+			gpios = <&pca9532 11 0>;
+			default-state = "off";
+		};
+		lede5 {
+			gpios = <&pca9532 12 0>;
+			default-state = "off";
+		};
+		lede6 {
+			gpios = <&pca9532 13 0>;
+			default-state = "off";
+		};
+		lede7 {
+			gpios = <&pca9532 14 0>;
+			default-state = "off";
+		};
+		lede8 {
+			gpios = <&pca9532 15 0>;
+			default-state = "off";
+		};
+	};
+};
+
+/* 3-axis accelerometer X,Y,Z (or AD-IN instead of Z) */
+&adc {
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+
+	uda1380: uda1380@18 {
+		compatible = "nxp,uda1380";
+		reg = <0x18>;
+		power-gpio = <&gpio 3 10 0>;
+		reset-gpio = <&gpio 3 2 0>;
+		dac-clk = "wspll";
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+	};
+
+	eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+	};
+
+	pca9532: pca9532@60 {
+		compatible = "nxp,pca9532";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0x60>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2cusb {
+	clock-frequency = <100000>;
+
+	isp1301: usb-transceiver@2d {
+		compatible = "nxp,isp1301";
+		reg = <0x2d>;
+	};
+};
+
+&mac {
+	phy-mode = "rmii";
+	use-iram;
+	status = "okay";
+};
+
+/* Here, choose exactly one from: ohci, usbd */
+&ohci /* &usbd */ {
+	transceiver = <&isp1301>;
+	status = "okay";
+};
+
+&sd {
+	wp-gpios = <&pca9532 5 0>;
+	cd-gpios = <&pca9532 4 0>;
+	cd-inverted;
+	bus-width = <4>;
+	status = "okay";
+};
+
+/* 128MB Flash via SLC NAND controller */
+&slc {
+	status = "okay";
+
+	nxp,wdr-clks = <14>;
+	nxp,wwidth = <260000000>;
+	nxp,whold = <104000000>;
+	nxp,wsetup = <200000000>;
+	nxp,rdr-clks = <14>;
+	nxp,rwidth = <34666666>;
+	nxp,rhold = <104000000>;
+	nxp,rsetup = <200000000>;
+	nand-on-flash-bbt;
+	gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		mtd0@0 {
+			label = "ea3250-boot";
+			reg = <0x00000000 0x00080000>;
+			read-only;
+		};
+
+		mtd1@80000 {
+			label = "ea3250-uboot";
+			reg = <0x00080000 0x000c0000>;
+			read-only;
+		};
+
+		mtd2@140000 {
+			label = "ea3250-kernel";
+			reg = <0x00140000 0x00400000>;
+		};
+
+		mtd3@540000 {
+			label = "ea3250-rootfs";
+			reg = <0x00540000 0x07ac0000>;
+		};
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&uart6 {
+	status = "okay";
+};

linux-7.2.3/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts

@@ -0,0 +1,236 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * PHYTEC phyCORE-LPC3250 board
+ *
+ * Copyright (C) 2015-2019 Vladimir Zapolskiy <vz@mleia.com>
+ * Copyright 2012 Roland Stigge <stigge@antcom.de>
+ */
+
+/dts-v1/;
+#include "lpc32xx.dtsi"
+
+/ {
+	model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250";
+	compatible = "phytec,phy3250", "nxp,lpc3250";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x4000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led0 { /* red */
+			gpios = <&gpio 5 1 0>; /* GPO_P3 1, GPIO 80, active high */
+			default-state = "off";
+		};
+
+		led1 { /* green */
+			gpios = <&gpio 5 14 0>; /* GPO_P3 14, GPIO 93, active high */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	panel: panel {
+		compatible = "sharp,lq035q7db03";
+		power-supply = <&reg_lcd>;
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&cldc_output>;
+			};
+		};
+	};
+
+	reg_backlight: regulator-backlight {
+		compatible = "regulator-fixed";
+		regulator-name = "backlight";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio 5 4 0>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	reg_lcd: regulator-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio 5 0 0>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	reg_sd: regulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio 5 5 0>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&clcd {
+	max-memory-bandwidth = <18710000>;
+	status = "okay";
+
+	port {
+		cldc_output: endpoint {
+			remote-endpoint = <&panel_input>;
+			arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+
+	uda1380: uda1380@18 {
+		compatible = "nxp,uda1380";
+		reg = <0x18>;
+		power-gpio = <&gpio 3 10 0>;
+		reset-gpio = <&gpio 3 2 0>;
+		dac-clk = "wspll";
+	};
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2cusb {
+	clock-frequency = <100000>;
+
+	isp1301: usb-transceiver@2c {
+		compatible = "nxp,isp1301";
+		reg = <0x2c>;
+	};
+};
+
+&key {
+	keypad,num-rows = <1>;
+	keypad,num-columns = <1>;
+	nxp,debounce-delay-ms = <3>;
+	nxp,scan-delay-ms = <34>;
+	linux,keymap = <0x00000002>;
+	status = "okay";
+};
+
+&mac {
+	phy-mode = "rmii";
+	use-iram;
+	status = "okay";
+};
+
+/* Here, choose exactly one from: ohci, usbd */
+&ohci /* &usbd */ {
+	transceiver = <&isp1301>;
+	status = "okay";
+};
+
+&sd {
+	wp-gpios = <&gpio 3 0 0>;
+	cd-gpios = <&gpio 3 1 0>;
+	cd-inverted;
+	bus-width = <4>;
+	vmmc-supply = <&reg_sd>;
+	status = "okay";
+};
+
+/* 64MB Flash via SLC NAND controller */
+&slc {
+	status = "okay";
+
+	nxp,wdr-clks = <14>;
+	nxp,wwidth = <40000000>;
+	nxp,whold = <100000000>;
+	nxp,wsetup = <100000000>;
+	nxp,rdr-clks = <14>;
+	nxp,rwidth = <40000000>;
+	nxp,rhold = <66666666>;
+	nxp,rsetup = <100000000>;
+	nand-on-flash-bbt;
+	gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		mtd0@0 {
+			label = "phy3250-boot";
+			reg = <0x00000000 0x00064000>;
+			read-only;
+		};
+
+		mtd1@64000 {
+			label = "phy3250-uboot";
+			reg = <0x00064000 0x00190000>;
+			read-only;
+		};
+
+		mtd2@1f4000 {
+			label = "phy3250-ubt-prms";
+			reg = <0x001f4000 0x00010000>;
+		};
+
+		mtd3@204000 {
+			label = "phy3250-kernel";
+			reg = <0x00204000 0x00400000>;
+		};
+
+		mtd4@604000 {
+			label = "phy3250-rootfs";
+			reg = <0x00604000 0x039fc000>;
+		};
+	};
+};
+
+&ssp0 {
+	num-cs = <1>;
+	cs-gpios = <&gpio 3 5 0>;
+	status = "okay";
+
+	eeprom: eeprom@0 {
+		compatible = "atmel,at25";
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+
+		pl022,interface = <0>;
+		pl022,com-mode = <0>;
+		pl022,rx-level-trig = <1>;
+		pl022,tx-level-trig = <1>;
+		pl022,ctrl-len = <11>;
+		pl022,wait-state = <0>;
+		pl022,duplex = <0>;
+
+		size = <0x8000>;
+		address-width = <16>;
+		pagesize = <64>;
+	};
+};
+
+&tsc {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};

linux-7.2.3/arch/arm/boot/dts/nxp/lpc/lpc32xx.dtsi

@@ -0,0 +1,540 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * NXP LPC32xx SoC
+ *
+ * Copyright (C) 2015-2019 Vladimir Zapolskiy <vz@mleia.com>
+ * Copyright 2012 Roland Stigge <stigge@antcom.de>
+ */
+
+#include <dt-bindings/clock/lpc32xx-clock.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "nxp,lpc3220";
+	interrupt-parent = <&mic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,arm926ej-s";
+			device_type = "cpu";
+			reg = <0x0>;
+		};
+	};
+
+	clocks {
+		xtal_32k: xtal_32k {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "xtal_32k";
+		};
+
+		xtal: xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <13000000>;
+			clock-output-names = "xtal";
+		};
+	};
+
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x00000000 0x00000000 0x10000000>,
+			 <0x20000000 0x20000000 0x30000000>,
+			 <0xe0000000 0xe0000000 0x04000000>;
+
+		iram: sram@8000000 {
+			compatible = "mmio-sram";
+			reg = <0x08000000 0x20000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x00000000 0x08000000 0x20000>;
+		};
+
+		/*
+		 * Enable either SLC or MLC
+		 */
+		slc: nand-controller@20020000 {
+			compatible = "nxp,lpc3220-slc";
+			reg = <0x20020000 0x1000>;
+			interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk LPC32XX_CLK_SLC>;
+			dmas = <&dma 1 1>;
+			dma-names = "rx-tx";
+			status = "disabled";
+		};
+
+		mlc: nand-controller@200a8000 {
+			compatible = "nxp,lpc3220-mlc";
+			reg = <0x200a8000 0x11000>;
+			interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk LPC32XX_CLK_MLC>;
+			dmas = <&dma 12 1>;
+			dma-names = "rx-tx";
+			status = "disabled";
+		};
+
+		dma: dma-controller@31000000 {
+			compatible = "arm,pl080", "arm,primecell";
+			reg = <0x31000000 0x1000>;
+			interrupts = <28 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk LPC32XX_CLK_DMA>;
+			clock-names = "apb_pclk";
+			dma-channels = <8>;
+			dma-requests = <16>;
+			lli-bus-interface-ahb1;
+			lli-bus-interface-ahb2;
+			mem-bus-interface-ahb1;
+			mem-bus-interface-ahb2;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			#dma-cells = <2>;
+		};
+
+		/*
+		 * Enable either ohci or usbd (gadget)!
+		 */
+		ohci: usb@31020000 {
+			compatible = "nxp,ohci-nxp", "usb-ohci";
+			reg = <0x31020000 0x300>;
+			interrupt-parent = <&sic1>;
+			interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&usbclk LPC32XX_USB_CLK_HOST>;
+			status = "disabled";
+		};
+
+		usbd: usbd@31020000 {
+			compatible = "nxp,lpc3220-udc";
+			reg = <0x31020000 0x300>;
+			interrupt-parent = <&sic1>;
+			interrupts = <29 IRQ_TYPE_LEVEL_HIGH>,
+				     <30 IRQ_TYPE_LEVEL_HIGH>,
+				     <28 IRQ_TYPE_LEVEL_HIGH>,
+				     <26 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&usbclk LPC32XX_USB_CLK_DEVICE>;
+			status = "disabled";
+		};
+
+		i2cusb: i2c@31020300 {
+			compatible = "nxp,pnx-i2c";
+			reg = <0x31020300 0x100>;
+			interrupt-parent = <&sic1>;
+			interrupts = <31 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&usbclk LPC32XX_USB_CLK_I2C>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		usbclk: clock-controller@31020f00 {
+			compatible = "nxp,lpc3220-usb-clk";
+			reg = <0x31020f00 0x100>;
+			#clock-cells = <1>;
+		};
+
+		clcd: clcd@31040000 {
+			compatible = "arm,pl111", "arm,primecell";
+			reg = <0x31040000 0x1000>;
+			interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk LPC32XX_CLK_LCD>, <&clk LPC32XX_CLK_LCD>;
+			clock-names = "clcdclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		mac: ethernet@31060000 {
+			compatible = "nxp,lpc-eth";
+			reg = <0x31060000 0x1000>;
+			interrupts = <29 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk LPC32XX_CLK_MAC>;
+			status = "disabled";
+		};
+
+		emc: memory-controller@31080000 {
+			compatible = "arm,pl175", "arm,primecell";
+			reg = <0x31080000 0x1000>;
+			clocks = <&clk LPC32XX_CLK_DDRAM>, <&clk LPC32XX_CLK_DDRAM>;
+			clock-names = "mpmcclk", "apb_pclk";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ranges = <0 0xe0000000 0x01000000>,
+				 <1 0xe1000000 0x01000000>,
+				 <2 0xe2000000 0x01000000>,
+				 <3 0xe3000000 0x01000000>;
+			status = "disabled";
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0x20000000 0x20000000 0x30000000>;
+
+			/*
+			 * ssp0 and spi1 are shared pins;
+			 * enable one in your board dts, as needed.
+			 */
+			ssp0: spi@20084000 {
+				compatible = "arm,pl022", "arm,primecell";
+				reg = <0x20084000 0x1000>;
+				interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk LPC32XX_CLK_SSP0>, <&clk LPC32XX_CLK_SSP0>;
+				clock-names = "sspclk", "apb_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi1: spi@20088000 {
+				compatible = "nxp,lpc3220-spi";
+				reg = <0x20088000 0x1000>;
+				clocks = <&clk LPC32XX_CLK_SPI1>;
+				dmas = <&dmamux 11 1 0>;
+				dma-names = "rx-tx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			/*
+			 * ssp1 and spi2 are shared pins;
+			 * enable one in your board dts, as needed.
+			 */
+			ssp1: spi@2008c000 {
+				compatible = "arm,pl022", "arm,primecell";
+				reg = <0x2008c000 0x1000>;
+				interrupts = <21 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk LPC32XX_CLK_SSP1>, <&clk LPC32XX_CLK_SSP1>;
+				clock-names = "sspclk", "apb_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi2: spi@20090000 {
+				compatible = "nxp,lpc3220-spi";
+				reg = <0x20090000 0x1000>;
+				clocks = <&clk LPC32XX_CLK_SPI2>;
+				dmas = <&dmamux 3 1 0>;
+				dma-names = "rx-tx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2s0: i2s@20094000 {
+				compatible = "nxp,lpc3220-i2s";
+				reg = <0x20094000 0x1000>;
+				interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk LPC32XX_CLK_I2S0>;
+				dmas = <&dma 0 1>, <&dma 13 1>;
+				dma-names = "rx", "tx";
+				#sound-dai-cells = <0>;
+				status = "disabled";
+			};
+
+			sd: mmc@20098000 {
+				compatible = "arm,pl180", "arm,primecell";
+				reg = <0x20098000 0x1000>;
+				interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
+					     <13 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk LPC32XX_CLK_SD>;
+				clock-names = "apb_pclk";
+				status = "disabled";
+			};
+
+			i2s1: i2s@2009c000 {
+				compatible = "nxp,lpc3220-i2s";
+				reg = <0x2009c000 0x1000>;
+				interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk LPC32XX_CLK_I2S1>;
+				dmas = <&dma 2 1>, <&dmamux 10 1 1>;
+				dma-names = "rx", "tx";
+				#sound-dai-cells = <0>;
+				status = "disabled";
+			};
+
+			/* UART5 first since it is the default console, ttyS0 */
+			uart5: serial@40090000 {
+				/* actually, ns16550a w/ 64 byte fifos! */
+				compatible = "nxp,lpc3220-uart";
+				reg = <0x40090000 0x1000>;
+				interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				clocks = <&clk LPC32XX_CLK_UART5>;
+				status = "disabled";
+			};
+
+			uart3: serial@40080000 {
+				compatible = "nxp,lpc3220-uart";
+				reg = <0x40080000 0x1000>;
+				interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				clocks = <&clk LPC32XX_CLK_UART3>;
+				status = "disabled";
+			};
+
+			uart4: serial@40088000 {
+				compatible = "nxp,lpc3220-uart";
+				reg = <0x40088000 0x1000>;
+				interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				clocks = <&clk LPC32XX_CLK_UART4>;
+				status = "disabled";
+			};
+
+			uart6: serial@40098000 {
+				compatible = "nxp,lpc3220-uart";
+				reg = <0x40098000 0x1000>;
+				interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				clocks = <&clk LPC32XX_CLK_UART6>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@400a0000 {
+				compatible = "nxp,pnx-i2c";
+				reg = <0x400a0000 0x100>;
+				interrupt-parent = <&sic1>;
+				interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk LPC32XX_CLK_I2C1>;
+			};
+
+			i2c2: i2c@400a8000 {
+				compatible = "nxp,pnx-i2c";
+				reg = <0x400a8000 0x100>;
+				interrupt-parent = <&sic1>;
+				interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clk LPC32XX_CLK_I2C2>;
+			};
+
+			mpwm: pwm@400e8000 {
+				compatible = "nxp,lpc3220-motor-pwm";
+				reg = <0x400e8000 0x78>;
+				interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+				clocks = <&clk LPC32XX_CLK_MCPWM>;
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		fab {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0x20000000 0x20000000 0x30000000>;
+
+			/* System Control Block */
+			syscon@40004000 {
+				compatible = "nxp,lpc3220-scb", "syscon", "simple-mfd";
+				reg = <0x40004000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x40004000 0x1000>;
+
+				clk: clock-controller@0 {
+					compatible = "nxp,lpc3220-clk";
+					reg = <0x00 0x114>;
+					#clock-cells = <1>;
+					clocks = <&xtal_32k>, <&xtal>;
+					clock-names = "xtal_32k", "xtal";
+				};
+
+				dmamux: dma-router@78 {
+					compatible = "nxp,lpc3220-dmamux";
+					reg = <0x78 0x8>;
+					dma-masters = <&dma>;
+					#dma-cells = <3>;
+				};
+			};
+
+			mic: interrupt-controller@40008000 {
+				compatible = "nxp,lpc3220-mic";
+				reg = <0x40008000 0x4000>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			sic1: interrupt-controller@4000c000 {
+				compatible = "nxp,lpc3220-sic";
+				reg = <0x4000c000 0x4000>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				interrupt-parent = <&mic>;
+				interrupts = <0 IRQ_TYPE_LEVEL_LOW>,
+					     <30 IRQ_TYPE_LEVEL_LOW>;
+				};
+
+			sic2: interrupt-controller@40010000 {
+				compatible = "nxp,lpc3220-sic";
+				reg = <0x40010000 0x4000>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				interrupt-parent = <&mic>;
+				interrupts = <1 IRQ_TYPE_LEVEL_LOW>,
+					     <31 IRQ_TYPE_LEVEL_LOW>;
+			};
+
+			uart1: serial@40014000 {
+				compatible = "nxp,lpc3220-hsuart";
+				reg = <0x40014000 0x1000>;
+				interrupts = <26 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
+			uart2: serial@40018000 {
+				compatible = "nxp,lpc3220-hsuart";
+				reg = <0x40018000 0x1000>;
+				interrupts = <25 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
+			uart7: serial@4001c000 {
+				compatible = "nxp,lpc3220-hsuart";
+				reg = <0x4001c000 0x1000>;
+				interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
+			rtc: rtc@40024000 {
+				compatible = "nxp,lpc3220-rtc";
+				reg = <0x40024000 0x1000>;
+				interrupt-parent = <&sic1>;
+				interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk LPC32XX_CLK_RTC>;
+			};
+
+			gpio: gpio@40028000 {
+				compatible = "nxp,lpc3220-gpio";
+				reg = <0x40028000 0x1000>;
+				gpio-controller;
+				#gpio-cells = <3>; /* bank, pin, flags */
+			};
+
+			timer4: timer@4002c000 {
+				compatible = "nxp,lpc3220-timer";
+				reg = <0x4002c000 0x1000>;
+				interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+				clocks = <&clk LPC32XX_CLK_TIMER4>;
+				clock-names = "timerclk";
+				status = "disabled";
+			};
+
+			timer5: timer@40030000 {
+				compatible = "nxp,lpc3220-timer";
+				reg = <0x40030000 0x1000>;
+				interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+				clocks = <&clk LPC32XX_CLK_TIMER5>;
+				clock-names = "timerclk";
+				status = "disabled";
+			};
+
+			watchdog: watchdog@4003c000 {
+				compatible = "nxp,pnx4008-wdt";
+				reg = <0x4003c000 0x1000>;
+				clocks = <&clk LPC32XX_CLK_WDOG>;
+			};
+
+			timer0: timer@40044000 {
+				compatible = "nxp,lpc3220-timer";
+				reg = <0x40044000 0x1000>;
+				clocks = <&clk LPC32XX_CLK_TIMER0>;
+				clock-names = "timerclk";
+				interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+			};
+
+			/*
+			 * TSC vs. ADC: Since those two share the same
+			 * hardware, you need to choose from one of the
+			 * following two and do 'status = "okay";' for one of
+			 * them
+			 */
+
+			adc: adc@40048000 {
+				compatible = "nxp,lpc3220-adc";
+				reg = <0x40048000 0x1000>;
+				interrupt-parent = <&sic1>;
+				interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk LPC32XX_CLK_ADC>;
+				status = "disabled";
+			};
+
+			tsc: tsc@40048000 {
+				compatible = "nxp,lpc3220-tsc";
+				reg = <0x40048000 0x1000>;
+				interrupt-parent = <&sic1>;
+				interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk LPC32XX_CLK_ADC>;
+				status = "disabled";
+			};
+
+			timer1: timer@4004c000 {
+				compatible = "nxp,lpc3220-timer";
+				reg = <0x4004c000 0x1000>;
+				interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+				clocks = <&clk LPC32XX_CLK_TIMER1>;
+				clock-names = "timerclk";
+			};
+
+			key: key@40050000 {
+				compatible = "nxp,lpc3220-key";
+				reg = <0x40050000 0x1000>;
+				clocks = <&clk LPC32XX_CLK_KEY>;
+				interrupt-parent = <&sic1>;
+				interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
+			timer2: timer@40058000 {
+				compatible = "nxp,lpc3220-timer";
+				reg = <0x40058000 0x1000>;
+				interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+				clocks = <&clk LPC32XX_CLK_TIMER2>;
+				clock-names = "timerclk";
+				status = "disabled";
+			};
+
+			pwm1: pwm@4005c000 {
+				compatible = "nxp,lpc3220-pwm";
+				reg = <0x4005c000 0x4>;
+				clocks = <&clk LPC32XX_CLK_PWM1>;
+				#pwm-cells = <3>;
+				assigned-clocks = <&clk LPC32XX_CLK_PWM1>;
+				assigned-clock-parents = <&clk LPC32XX_CLK_PERIPH>;
+				status = "disabled";
+			};
+
+			pwm2: pwm@4005c004 {
+				compatible = "nxp,lpc3220-pwm";
+				reg = <0x4005c004 0x4>;
+				clocks = <&clk LPC32XX_CLK_PWM2>;
+				#pwm-cells = <3>;
+				assigned-clocks = <&clk LPC32XX_CLK_PWM2>;
+				assigned-clock-parents = <&clk LPC32XX_CLK_PERIPH>;
+				status = "disabled";
+			};
+
+			timer3: timer@40060000 {
+				compatible = "nxp,lpc3220-timer";
+				reg = <0x40060000 0x1000>;
+				interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+				clocks = <&clk LPC32XX_CLK_TIMER3>;
+				clock-names = "timerclk";
+				status = "disabled";
+			};
+		};
+	};
+};

linux-7.2.3/arch/arm/boot/dts/nxp/lpc/lpc4337-ciaa.dts

@@ -0,0 +1,221 @@
+/*
+ * CIAA NXP LPC4337 (http://www.proyecto-ciaa.com.ar)
+ *
+ * Copyright (C) 2015 VanguardiaSur - www.vanguardiasur.com.ar
+ *
+ * This code is released using a dual license strategy: BSD/GPL
+ * You can choose the licence that better fits your requirements.
+ *
+ * Released under the terms of 3-clause BSD License
+ * Released under the terms of GNU General Public License Version 2.0
+ */
+/dts-v1/;
+
+#include "lpc18xx.dtsi"
+#include "lpc4357.dtsi"
+
+#include "dt-bindings/gpio/gpio.h"
+
+/ {
+	model = "CIAA NXP LPC4337";
+	compatible = "ciaa,lpc4337", "nxp,lpc4337", "nxp,lpc4350";
+
+	aliases {
+		serial0 = &uart2;
+		serial1 = &uart3;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+		stdout-path = &uart2;
+	};
+
+	memory@28000000 {
+		device_type = "memory";
+		reg = <0x28000000 0x0800000>; /* 8 MB */
+	};
+};
+
+&pinctrl {
+	enet_rmii_pins: enet-rmii-pins {
+		enet_rmii_rxd_cfg {
+			pins = "p1_15", "p0_0";
+			function = "enet";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		enet_rmii_txd_cfg {
+			pins = "p1_18", "p1_20";
+			function = "enet";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		enet_rmii_rx_dv_cfg {
+			pins = "p1_16";
+			function = "enet";
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		enet_rmii_tx_en_cfg {
+			pins = "p0_1";
+			function = "enet";
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		enet_ref_clk_cfg {
+			pins = "p1_19";
+			function = "enet";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		enet_mdio_cfg {
+			pins = "p1_17";
+			function = "enet";
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		enet_mdc_cfg {
+			pins = "p7_7";
+			function = "enet";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+	};
+
+	i2c0_pins: i2c0-pins {
+		i2c0_pins_cfg {
+			pins = "i2c0_scl", "i2c0_sda";
+			function = "i2c0";
+			input-enable;
+		};
+	};
+
+	ssp_pins: ssp-pins {
+		ssp1_cs_cfg {
+			pins = "p6_7";
+			function = "gpio";
+			bias-pull-up;
+			bias-disable;
+		};
+
+		ssp1_miso_mosi_cfg {
+			pins = "p1_3", "p1_4";
+			function = "ssp1";
+			slew-rate = <1>;
+			bias-pull-down;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		ssp1_sck_cfg {
+			pins = "pf_4";
+			function = "ssp1";
+			slew-rate = <1>;
+			bias-disable;
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		uart2_rx_cfg {
+			pins = "p7_2";
+			function = "uart2";
+			bias-disable;
+			input-enable;
+		};
+
+		uart2_tx_cfg {
+			pins = "p7_1";
+			function = "uart2";
+			bias-disable;
+		};
+	};
+
+	uart3_pins: uart3-pins {
+		uart3_rx_cfg {
+			pins = "p2_4";
+			function = "uart3";
+			bias-disable;
+			input-enable;
+		};
+
+		uart3_tx_cfg {
+			pins = "p2_3";
+			function = "uart3";
+			bias-disable;
+		};
+	};
+};
+
+&enet_tx_clk {
+	clock-frequency = <50000000>;
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <400000>;
+
+	eeprom@50 {
+		compatible = "microchip,24c512", "atmel,24c512";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "microchip,24c02", "atmel,24c02";
+		reg = <0x51>;
+	};
+
+	eeprom@54 {
+		compatible = "microchip,24c512", "atmel,24c512";
+		reg = <0x54>;
+	};
+};
+
+&mac {
+	status = "okay";
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&enet_rmii_pins>;
+};
+
+&sct_pwm {
+	status = "okay";
+};
+
+&ssp1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ssp_pins>;
+	cs-gpios = <&gpio LPC_GPIO(5,15) GPIO_ACTIVE_HIGH>;
+	num-cs = <1>;
+};
+
+&uart2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};

linux-7.2.3/arch/arm/boot/dts/nxp/lpc/lpc4350-hitex-eval.dts

@@ -0,0 +1,485 @@
+/*
+ * Hitex LPC4350 Evaluation Board
+ *
+ * Copyright 2015 Ariel D'Alessandro <ariel.dalessandro@gmail.com>
+ *
+ * This code is released using a dual license strategy: BSD/GPL
+ * You can choose the licence that better fits your requirements.
+ *
+ * Released under the terms of 3-clause BSD License
+ * Released under the terms of GNU General Public License Version 2.0
+ *
+ */
+/dts-v1/;
+
+#include "lpc18xx.dtsi"
+#include "lpc4350.dtsi"
+
+#include "dt-bindings/input/input.h"
+#include "dt-bindings/gpio/gpio.h"
+
+/ {
+	model = "Hitex LPC4350 Evaluation Board";
+	compatible = "hitex,lpc4350-eval-board", "nxp,lpc4350";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	memory@28000000 {
+		device_type = "memory";
+		reg = <0x28000000 0x800000>; /* 8 MB */
+	};
+
+	pca_buttons {
+		compatible = "gpio-keys-polled";
+		poll-interval = <100>;
+		autorepeat;
+
+		button-0 {
+			label = "joy:right";
+			linux,code = <KEY_RIGHT>;
+			gpios = <&pca_gpio 8 GPIO_ACTIVE_LOW>;
+		};
+
+		button-1 {
+			label = "joy:up";
+			linux,code = <KEY_UP>;
+			gpios = <&pca_gpio 9 GPIO_ACTIVE_LOW>;
+		};
+
+
+		button-2 {
+			label = "joy:enter";
+			linux,code = <KEY_ENTER>;
+			gpios = <&pca_gpio 10 GPIO_ACTIVE_LOW>;
+		};
+
+		button-3 {
+			label = "joy:left";
+			linux,code = <KEY_LEFT>;
+			gpios = <&pca_gpio 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-4 {
+			label = "joy:down";
+			linux,code = <KEY_DOWN>;
+			gpios = <&pca_gpio 12 GPIO_ACTIVE_LOW>;
+		};
+
+		button-5 {
+			label = "user:sw3";
+			linux,code = <KEY_F1>;
+			gpios = <&pca_gpio 13 GPIO_ACTIVE_LOW>;
+		};
+
+		button-6 {
+			label = "user:sw4";
+			linux,code = <KEY_F2>;
+			gpios = <&pca_gpio 14 GPIO_ACTIVE_LOW>;
+		};
+
+		button-7 {
+			label = "user:sw5";
+			linux,code = <KEY_F3>;
+			gpios = <&pca_gpio 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	pca_leds {
+		compatible = "gpio-leds";
+
+		led0 {
+			label = "ext:led0";
+			gpios = <&pca_gpio 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led1 {
+			label = "ext:led1";
+			gpios = <&pca_gpio 1 GPIO_ACTIVE_LOW>;
+		};
+
+		led2 {
+			label = "ext:led2";
+			gpios = <&pca_gpio 2 GPIO_ACTIVE_LOW>;
+		};
+
+		led3 {
+			label = "ext:led3";
+			gpios = <&pca_gpio 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	vcc: vcc_fixed {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3io";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&pinctrl {
+	adc1_pins: adc1-pins {
+		adc1_pins_cfg {
+			pins = "pf_9";
+			function = "adc";
+			input-disable;
+			bias-disable;
+		};
+	};
+
+	emc_pins: emc-pins {
+		emc_addr0_23_cfg {
+			pins =	"p2_9",  "p2_10", "p2_11", "p2_12",
+				"p2_13", "p1_0",  "p1_1",  "p1_2",
+				"p2_8",  "p2_7",  "p2_6",  "p2_2",
+				"p2_1",  "p2_0",  "p6_8",  "p6_7",
+				"pd_16", "pd_15", "pe_0",  "pe_1",
+				"pe_2",  "pe_3",  "pe_4",  "pa_4";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_data0_15_cfg {
+			pins =	"p1_7",  "p1_8",  "p1_9",  "p1_10",
+				"p1_11", "p1_12", "p1_13", "p1_14",
+				"p5_4",  "p5_5",  "p5_6",  "p5_7",
+				"p5_0",  "p5_1",  "p5_2",  "p5_3";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_we_oe_cfg {
+			pins = "p1_6", "p1_3";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_bls0_3_cfg {
+			pins = "p1_4", "p6_6", "pd_13", "pd_10";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_cs0_cs2_cfg {
+			pins = "p1_5", "pd_12";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_sdram_dqm0_3_cfg {
+			pins = "p6_12", "p6_10", "pd_0", "pe_13";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_sdram_ras_cas_cfg {
+			pins = "p6_5", "p6_4";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_sdram_dycs0_cfg {
+			pins = "p6_9";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_sdram_cke_cfg {
+			pins = "p6_11";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_sdram_clock_cfg {
+			pins = "clk0", "clk1", "clk2", "clk3";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+	};
+
+	enet_mii_pins: enet-mii-pins {
+		enet_mii_rxd0_3_cfg {
+			pins = "p1_15", "p0_0", "p9_3", "p9_2";
+			function = "enet";
+			bias-disable;
+			input-enable;
+		};
+
+		enet_mii_txd0_3_cfg {
+			pins = "p1_18", "p1_20", "p9_4", "p9_5";
+			function = "enet";
+			bias-disable;
+		};
+
+		enet_mii_crs_col_cfg {
+			pins = "p9_0", "p9_6";
+			function = "enet";
+			bias-disable;
+			input-enable;
+		};
+
+		enet_mii_rx_clk_dv_er_cfg {
+			pins = "pc_0", "p1_16", "p9_1";
+			function = "enet";
+			bias-disable;
+			input-enable;
+		};
+
+		enet_mii_tx_clk_en_cfg {
+			pins = "p1_19", "p0_1";
+			function = "enet";
+			bias-disable;
+			input-enable;
+		};
+
+		enet_mdio_cfg {
+			pins = "p1_17";
+			function = "enet";
+			bias-disable;
+			input-enable;
+		};
+
+		enet_mdc_cfg {
+			pins = "pc_1";
+			function = "enet";
+			bias-disable;
+		};
+	};
+
+	i2c0_pins: i2c0-pins {
+		i2c0_pins_cfg {
+			pins = "i2c0_scl", "i2c0_sda";
+			function = "i2c0";
+			input-enable;
+		};
+	};
+
+	spifi_pins: spifi-pins {
+		spifi_clk_cfg {
+			pins = "p3_3";
+			function = "spifi";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		spifi_mosi_miso_sio2_3_cfg {
+			pins = "p3_7", "p3_6", "p3_5", "p3_4";
+			function = "spifi";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		spifi_cs_cfg {
+			pins = "p3_8";
+			function = "spifi";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+	};
+
+	uart0_pins: uart0-pins {
+		uart0_rx_cfg {
+			pins = "pf_11";
+			function = "uart0";
+			input-schmitt-disable;
+			bias-disable;
+			input-enable;
+		};
+
+		uart0_tx_cfg {
+			pins = "pf_10";
+			function = "uart0";
+			bias-pull-down;
+		};
+	};
+};
+
+&adc1 {
+	status = "okay";
+	vref-supply = <&vcc>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc1_pins>;
+};
+
+&emc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&emc_pins>;
+
+	cs0 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges;
+
+		mpmc,cs = <0>;
+		mpmc,memory-width = <16>;
+		mpmc,byte-lane-low;
+		mpmc,write-enable-delay = <0>;
+		mpmc,output-enable-delay = <0>;
+		mpmc,read-access-delay = <70>;
+		mpmc,page-mode-read-delay = <70>;
+
+		flash@0,0 {
+			compatible = "sst,sst39vf320", "cfi-flash";
+			reg = <0 0 0x400000>;
+			bank-width = <2>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "bootloader";
+				reg = <0x000000 0x040000>; /* 256 KiB */
+			};
+
+			partition@1 {
+				label = "kernel";
+				reg = <0x040000 0x2C0000>; /* 2.75 MiB */
+			};
+
+			partition@2 {
+				label = "rootfs";
+				reg = <0x300000 0x100000>; /* 1 MiB */
+			};
+		};
+	};
+
+	cs2 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges;
+
+		mpmc,cs = <2>;
+		mpmc,memory-width = <16>;
+		mpmc,byte-lane-low;
+		mpmc,write-enable-delay = <0>;
+		mpmc,output-enable-delay = <30>;
+		mpmc,read-access-delay = <90>;
+		mpmc,page-mode-read-delay = <55>;
+		mpmc,write-access-delay = <55>;
+		mpmc,turn-round-delay = <55>;
+
+		ext_sram: sram@2,0 {
+			compatible = "mmio-sram";
+			reg = <2 0 0x80000>; /* 512 KiB SRAM on IS62WV25616 */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 2 0 0x80000>;
+		};
+	};
+};
+
+&enet_tx_clk {
+	clock-frequency = <25000000>;
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <400000>;
+
+	/* NXP SE97BTP with temperature sensor + eeprom */
+	sensor@18 {
+		compatible = "nxp,se97", "jedec,jc-42.4-temp";
+		reg = <0x18>;
+	};
+
+	eeprom@50 {
+		compatible = "nxp,24c02", "atmel,24c02";
+		reg = <0x50>;
+	};
+
+	pca_gpio: gpio@24 {
+		compatible = "nxp,pca9673";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&mac {
+	status = "okay";
+	phy-mode = "mii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&enet_mii_pins>;
+};
+
+&spifi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spifi_pins>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "bootloader";
+			reg = <0x000000 0x040000>; /* 256 KiB */
+		};
+
+		partition@1 {
+			label = "kernel";
+			reg = <0x040000 0x2c0000>; /* 2.75 MiB */
+		};
+
+		partition@2 {
+			label = "rootfs";
+			reg = <0x300000 0x500000>; /* 5 MiB */
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+};

linux-7.2.3/arch/arm/boot/dts/nxp/lpc/lpc4350.dtsi

@@ -0,0 +1,48 @@
+/*
+ * NXP LPC4350 and LPC4330 SoC
+ *
+ * Copyright 2015 Ariel D'Alessandro <ariel.dalessandro@gmail.com>
+ *
+ * This code is released using a dual license strategy: BSD/GPL
+ * You can choose the licence that better fits your requirements.
+ *
+ * Released under the terms of 3-clause BSD License
+ * Released under the terms of GNU General Public License Version 2.0
+ *
+ */
+
+/ {
+	compatible = "nxp,lpc4350", "nxp,lpc4330";
+
+	cpus {
+		cpu@0 {
+			compatible = "arm,cortex-m4";
+		};
+	};
+
+	soc {
+		sram0: sram@10000000 {
+			compatible = "mmio-sram";
+			reg = <0x10000000 0x20000>; /* 96 + 32 KiB local SRAM */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+		};
+
+		sram1: sram@10080000 {
+			compatible = "mmio-sram";
+			reg = <0x10080000 0x12000>; /* 64 + 8 KiB local SRAM */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+		};
+
+		sram2: sram@20000000 {
+			compatible = "mmio-sram";
+			reg = <0x20000000 0x10000>; /* 4 x 16 KiB AHB SRAM */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+		};
+	};
+};

linux-7.2.3/arch/arm/boot/dts/nxp/lpc/lpc4357-ea4357-devkit.dts

@@ -0,0 +1,624 @@
+/*
+ * Embedded Artist LPC4357 Developer's Kit
+ *
+ * Copyright 2015 Joachim Eastwood <manabian@gmail.com>
+ *
+ * This code is released using a dual license strategy: BSD/GPL
+ * You can choose the licence that better fits your requirements.
+ *
+ * Released under the terms of 3-clause BSD License
+ * Released under the terms of GNU General Public License Version 2.0
+ *
+ */
+/dts-v1/;
+
+#include "lpc18xx.dtsi"
+#include "lpc4357.dtsi"
+
+#include "dt-bindings/input/input.h"
+#include "dt-bindings/gpio/gpio.h"
+
+/ {
+	model = "Embedded Artists' LPC4357 Developer's Kit";
+	compatible = "ea,lpc4357-developers-kit", "nxp,lpc4357", "nxp,lpc4350";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	memory@28000000 {
+		device_type = "memory";
+		reg = <0x28000000 0x2000000>; /* 32 MB */
+	};
+
+	vcc: vcc_fixed {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	/* vmmc is controlled by sdmmc host internally */
+	vmmc: vmmc_fixed {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	gpio_joystick {
+		compatible = "gpio-keys-polled";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_joystick_pins>;
+		poll-interval = <100>;
+		autorepeat;
+
+		button-0 {
+			label = "joy_enter";
+			linux,code = <KEY_ENTER>;
+			gpios = <&gpio LPC_GPIO(4,8) GPIO_ACTIVE_LOW>;
+		};
+
+		button-1 {
+			label = "joy_left";
+			linux,code = <KEY_LEFT>;
+			gpios = <&gpio LPC_GPIO(4,9) GPIO_ACTIVE_LOW>;
+		};
+
+		button-2 {
+			label = "joy_up";
+			linux,code = <KEY_UP>;
+			gpios = <&gpio LPC_GPIO(4,10) GPIO_ACTIVE_LOW>;
+		};
+
+		button-3 {
+			label = "joy_right";
+			linux,code = <KEY_RIGHT>;
+			gpios = <&gpio LPC_GPIO(4,12) GPIO_ACTIVE_LOW>;
+		};
+
+		button-4 {
+			label = "joy_down";
+			linux,code = <KEY_DOWN>;
+			gpios = <&gpio LPC_GPIO(4,13) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds_mmio {
+		compatible = "gpio-leds";
+
+		led1 {
+			gpios = <&mmio_leds 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led2 {
+			gpios = <&mmio_leds 14 GPIO_ACTIVE_HIGH>;
+		};
+
+		led3 {
+			gpios = <&mmio_leds 13 GPIO_ACTIVE_HIGH>;
+		};
+
+		led4 {
+			gpios = <&mmio_leds 12 GPIO_ACTIVE_HIGH>;
+		};
+
+		led5 {
+			gpios = <&mmio_leds 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		led6 {
+			gpios = <&mmio_leds 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		led7 {
+			gpios = <&mmio_leds 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		led8 {
+			gpios = <&mmio_leds 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led9 {
+			gpios = <&mmio_leds 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led10 {
+			gpios = <&mmio_leds 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led11 {
+			gpios = <&mmio_leds 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led12 {
+			gpios = <&mmio_leds 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		led13 {
+			gpios = <&mmio_leds 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led14 {
+			gpios = <&mmio_leds 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		led15 {
+			gpios = <&mmio_leds 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		led16 {
+			gpios = <&mmio_leds 0 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&pinctrl {
+	emc_pins: emc-pins {
+		emc_addr0_23_cfg {
+			pins =	"p2_9",  "p2_10", "p2_11", "p2_12",
+				"p2_13", "p1_0",  "p1_1",  "p1_2",
+				"p2_8",  "p2_7",  "p2_6",  "p2_2",
+				"p2_1",  "p2_0",  "p6_8",  "p6_7",
+				"pd_16", "pd_15", "pe_0",  "pe_1",
+				"pe_2",  "pe_3",  "pe_4",  "pa_4";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_data0_31_cfg {
+			pins =	"p1_7",  "p1_8",  "p1_9",  "p1_10",
+				"p1_11", "p1_12", "p1_13", "p1_14",
+				"p5_4",  "p5_5",  "p5_6",  "p5_7",
+				"p5_0",  "p5_1",  "p5_2",  "p5_3",
+				"pd_2",  "pd_3",  "pd_4",  "pd_5",
+				"pd_6",  "pd_7",  "pd_8",  "pd_9",
+				"pe_5",  "pe_6",  "pe_7",  "pe_8",
+				"pe_9",  "pe_10", "pe_11", "pe_12";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_we_oe_cfg {
+			pins = "p1_6", "p1_3";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_bls0_3_cfg {
+			pins = "p1_4", "p6_6", "pd_13", "pd_10";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_cs0_3_cfg {
+			pins = "p1_5", "p6_3", "pd_12", "pd_11";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_sdram_dqm0_3_cfg {
+			pins = "p6_12", "p6_10", "pd_0", "pe_13";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_sdram_ras_cas_cfg {
+			pins = "p6_5", "p6_4";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_sdram_dycs0_cfg {
+			pins = "p6_9";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_sdram_cke_cfg {
+			pins = "p6_11";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		emc_sdram_clock_cfg {
+			pins = "clk0", "clk1", "clk2", "clk3";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+	};
+
+	enet_rmii_pins: enet-rmii-pins {
+		enet_rmii_rxd_cfg {
+			pins = "p1_15", "p0_0";
+			function = "enet";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		enet_rmii_txd_cfg {
+			pins = "p1_18", "p1_20";
+			function = "enet";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		enet_rmii_rx_dv_cfg {
+			pins = "p1_16";
+			function = "enet";
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		enet_rmii_tx_en_cfg {
+			pins = "p0_1";
+			function = "enet";
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		enet_ref_clk_cfg {
+			pins = "p1_19";
+			function = "enet";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		enet_mdio_cfg {
+			pins = "p1_17";
+			function = "enet";
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		enet_mdc_cfg {
+			pins = "pc_1";
+			function = "enet";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+	};
+
+	gpio_joystick_pins: gpio-joystick-pins {
+		gpio_joystick_cfg {
+			pins =	"p9_0", "p9_1", "pa_1", "pa_2", "pa_3";
+			function = "gpio";
+			input-enable;
+			bias-disable;
+		};
+	};
+
+	i2c0_pins: i2c0-pins {
+		i2c0_pins_cfg {
+			pins = "i2c0_scl", "i2c0_sda";
+			function = "i2c0";
+			input-enable;
+		};
+	};
+
+	sdmmc_pins: sdmmc-pins {
+		sdmmc_clk_cfg {
+			pins = "pc_0";
+			function = "sdmmc";
+			slew-rate = <1>;
+			bias-pull-down;
+		};
+
+		sdmmc_cmd_dat0_3_cfg {
+			pins = "pc_4", "pc_5", "pc_6", "pc_7", "pc_10";
+			function = "sdmmc";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		sdmmc_cd_cfg {
+			pins = "pc_8";
+			function = "sdmmc";
+			bias-pull-down;
+			input-enable;
+		};
+
+		sdmmc_pow_cfg {
+			pins = "pc_9";
+			function = "sdmmc";
+			bias-pull-down;
+		};
+	};
+
+	spifi_pins: spifi-pins {
+		spifi_clk_cfg {
+			pins = "p3_3";
+			function = "spifi";
+			slew-rate = <1>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		spifi_mosi_miso_sio2_3_cfg {
+			pins = "p3_7", "p3_6", "p3_5", "p3_4";
+			function = "spifi";
+			slew-rate = <0>;
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		spifi_cs_cfg {
+			pins = "p3_8";
+			function = "spifi";
+			bias-disable;
+		};
+	};
+
+	ssp0_pins: ssp0-pins {
+		ssp0_sck_miso_mosi_cfg {
+			pins = "pf_0", "pf_2", "pf_3";
+			function = "ssp0";
+			slew-rate = <1>;
+			bias-pull-down;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		ssp0_ssel_cfg {
+			pins = "pf_1";
+			function = "ssp0";
+			bias-pull-up;
+		};
+	};
+
+	uart0_pins: uart0-pins {
+		uart0_rx_cfg {
+			pins = "pf_11";
+			function = "uart0";
+			input-schmitt-disable;
+			bias-disable;
+			input-enable;
+		};
+
+		uart0_tx_cfg {
+			pins = "pf_10";
+			function = "uart0";
+			bias-pull-down;
+		};
+	};
+
+	uart3_pins: uart3-pins {
+		uart3_rx_cfg {
+			pins = "p2_4";
+			function = "uart3";
+			input-schmitt-disable;
+			bias-disable;
+			input-enable;
+		};
+
+		uart3_tx_cfg {
+			pins = "p9_3";
+			function = "uart3";
+			bias-pull-down;
+		};
+	};
+
+	usb0_pins: usb0-pins {
+		usb0_pwr_enable_cfg {
+			pins = "p2_3";
+			function = "usb0";
+		};
+
+		usb0_pwr_fault_cfg {
+			pins = "p8_0";
+			function = "usb0";
+			bias-disable;
+			input-enable;
+		};
+	};
+};
+
+&adc0 {
+	status = "okay";
+	vref-supply = <&vcc>;
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <400000>;
+
+	mma7455@1d {
+		compatible = "fsl,mma7455";
+		reg = <0x1d>;
+	};
+
+	temperature-sensor@48 {
+		compatible = "national,lm75b";
+		reg = <0x48>;
+	};
+
+	eeprom@57 {
+		compatible = "microchip,24c64", "atmel,24c64";
+		reg = <0x57>;
+	};
+};
+
+&dac {
+	status = "okay";
+	vref-supply = <&vcc>;
+};
+
+&emc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&emc_pins>;
+
+	cs0 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges;
+
+		mpmc,cs = <0>;
+		mpmc,memory-width = <16>;
+		mpmc,byte-lane-low;
+		mpmc,write-enable-delay = <0>;
+		mpmc,output-enable-delay = <0>;
+		mpmc,read-access-delay = <70>;
+		mpmc,page-mode-read-delay = <70>;
+
+		flash@0,0 {
+			compatible = "sst,sst39vf320", "cfi-flash";
+			reg = <0 0 0x400000>;
+			bank-width = <2>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "bootloader";
+				reg = <0x000000 0x040000>; /* 256 KiB */
+			};
+
+			partition@1 {
+				label = "kernel";
+				reg = <0x040000 0x2c0000>; /* 2.75 MiB */
+			};
+
+			partition@2 {
+				label = "rootfs";
+				reg = <0x300000 0x100000>; /* 1 MiB */
+			};
+		};
+	};
+
+	cs2 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges;
+
+		mpmc,cs = <2>;
+		mpmc,memory-width = <16>;
+
+		mmio_leds: gpio@2,0 {
+			compatible = "ti,7416374";
+			reg = <2 0 0x2>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+	};
+};
+
+&enet_tx_clk {
+	clock-frequency = <50000000>;
+};
+
+&mac {
+	status = "okay";
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&enet_rmii_pins>;
+};
+
+&mmcsd {
+	status = "okay";
+	bus-width = <4>;
+	vmmc-supply = <&vmmc>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_pins>;
+};
+
+&spifi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spifi_pins>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-cpol;
+		spi-cpha;
+		spi-rx-bus-width = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "data";
+			reg = <0 0x200000>;
+		};
+	};
+};
+
+&ssp0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ssp0_pins>;
+	num-cs = <1>;
+};
+
+&uart0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+};
+
+&uart3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
+
+&usb0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_pins>;
+};

linux-7.2.3/arch/arm/boot/dts/nxp/lpc/lpc4357-myd-lpc4357.dts

@@ -0,0 +1,621 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * MYIR Tech MYD-LPC4357 Development Board with 800x480 7" TFT panel
+ *
+ * Copyright (C) 2016-2018 Vladimir Zapolskiy <vz@mleia.com>
+ */
+
+/dts-v1/;
+
+#include "lpc18xx.dtsi"
+#include "lpc4357.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "MYIR Tech LPC4357 Development Board";
+	compatible = "myir,myd-lpc4357", "nxp,lpc4357";
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	memory@28000000 {
+		device_type = "memory";
+		reg = <0x28000000 0x2000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins>;
+
+		led1 {
+			gpios = <&gpio LPC_GPIO(6,15) GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led2 {
+			gpios = <&gpio LPC_GPIO(6,16) GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led3 {
+			gpios = <&gpio LPC_GPIO(6,17) GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led4 {
+			gpios = <&gpio LPC_GPIO(6,10) GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led5 {
+			gpios = <&gpio LPC_GPIO(7,14) GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led6 {
+			gpios = <&gpio LPC_GPIO(6,14) GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	panel: panel {
+		compatible = "innolux,at070tn92";
+		power-supply = <&vcc>;
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&lcdc_output>;
+			};
+		};
+	};
+
+	vcc: vcc_fixed {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vmmc: vmmc_fixed {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&pinctrl {
+	can0_pins: can0-pins {
+		can_rd_cfg {
+			pins = "p3_1";
+			function = "can0";
+			input-enable;
+		};
+
+		can_td_cfg {
+			pins = "p3_2";
+			function = "can0";
+		};
+	};
+
+	can1_pins: can1-pins {
+		can_rd_cfg {
+			pins = "pe_1";
+			function = "can1";
+			input-enable;
+		};
+
+		can_td_cfg {
+			pins = "pe_0";
+			function = "can1";
+		};
+	};
+
+	emc_pins: emc-pins {
+		emc_addr0_22_cfg {
+			pins = "p2_9",  "p2_10", "p2_11", "p2_12",
+			       "p2_13", "p1_0",  "p1_1",  "p1_2",
+			       "p2_8",  "p2_7",  "p2_6",  "p2_2",
+			       "p2_1",  "p2_0",  "p6_8",  "p6_7",
+			       "pd_16", "pd_15", "pe_0",  "pe_1",
+			       "pe_2",  "pe_3",  "pe_4";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		emc_data0_15_cfg {
+			pins = "p1_7",  "p1_8",  "p1_9",  "p1_10",
+			       "p1_11", "p1_12", "p1_13", "p1_14",
+			       "p5_4",  "p5_5",  "p5_6",  "p5_7",
+			       "p5_0",  "p5_1",  "p5_2",  "p5_3";
+			function = "emc";
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		emc_we_oe_cfg {
+			pins = "p1_6", "p1_3";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		emc_cs0_cfg {
+			pins = "p1_5";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		emc_sdram_dqm0_1_cfg {
+			pins = "p6_12", "p6_10";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		emc_sdram_ras_cas_cfg {
+			pins = "p6_5", "p6_4";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		emc_sdram_dycs0_cfg {
+			pins = "p6_9";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		emc_sdram_cke_cfg {
+			pins = "p6_11";
+			function = "emc";
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		emc_sdram_clock_cfg {
+			pins = "clk0";
+			function = "emc";
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <1>;
+			bias-disable;
+		};
+	};
+
+	enet_rmii_pins: enet-rmii-pins {
+		enet_rmii_rxd_cfg {
+			pins = "p1_15", "p0_0";
+			function = "enet";
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		enet_rmii_txd_cfg {
+			pins = "p1_18", "p1_20";
+			function = "enet";
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		enet_rmii_rx_dv_cfg {
+			pins = "p1_16";
+			function = "enet";
+			input-enable;
+			input-schmitt-disable;
+			bias-disable;
+		};
+
+		enet_mdio_cfg {
+			pins = "p1_17";
+			function = "enet";
+			input-enable;
+			input-schmitt-disable;
+			bias-disable;
+		};
+
+		enet_mdc_cfg {
+			pins = "pc_1";
+			function = "enet";
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		enet_rmii_tx_en_cfg {
+			pins = "p0_1";
+			function = "enet";
+			bias-disable;
+		};
+
+		enet_ref_clk_cfg {
+			pins = "p1_19";
+			function = "enet";
+			slew-rate = <1>;
+			input-enable;
+			input-schmitt-disable;
+			bias-disable;
+		};
+	};
+
+	i2c0_pins: i2c0-pins {
+		i2c0_pins_cfg {
+			pins = "i2c0_scl", "i2c0_sda";
+			function = "i2c0";
+			input-enable;
+		};
+	};
+
+	i2c1_pins: i2c1-pins {
+		i2c1_pins_cfg {
+			pins = "pe_15", "pe_13";
+			function = "i2c1";
+			input-enable;
+		};
+	};
+
+	lcd_pins: lcd-pins {
+		lcd_vd0_23_cfg {
+			pins = "p4_1", "p4_4", "p4_3",  "p4_2",
+			       "p8_7", "p8_6", "p8_5",  "p8_4",
+			       "p7_5", "p4_8", "p4_10", "p4_9",
+			       "p8_3", "pb_6", "pb_5",  "pb_4",
+			       "p7_4", "p7_3", "p7_2",  "p7_1",
+			       "pb_3", "pb_2", "pb_1",  "pb_0";
+			function = "lcd";
+		};
+
+		lcd_vsync_en_dclk_lp_pwr_cfg {
+			pins = "p4_5", "p4_6", "p4_7", "p7_6", "p7_7";
+			function = "lcd";
+		};
+	};
+
+	led_pins: led-pins {
+		led_1_6_cfg {
+			pins = "pd_1", "pd_2", "pd_3", "pc_11", "pe_14", "pd_0";
+			function = "gpio";
+			bias-pull-down;
+		};
+	};
+
+	sdmmc_pins: sdmmc-pins {
+		sdmmc_clk_cfg {
+			pins = "pc_0";
+			function = "sdmmc";
+			slew-rate = <1>;
+			bias-pull-down;
+		};
+
+		sdmmc_cmd_dat0_3_cfg {
+			pins = "pc_4", "pc_5", "pc_6", "pc_7", "pc_10";
+			function = "sdmmc";
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		sdmmc_cd_cfg {
+			pins = "pc_8";
+			function = "sdmmc";
+			input-enable;
+			bias-pull-down;
+		};
+	};
+
+	spifi_pins: spifi-pins {
+		spifi_sck_cfg {
+			pins = "p3_3";
+			function = "spifi";
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		spifi_mosi_miso_sio2_sio3_cfg {
+			pins = "p3_7", "p3_6", "p3_5", "p3_4";
+			function = "spifi";
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <1>;
+			bias-disable;
+		};
+
+		spifi_cs_cfg {
+			pins = "p3_8";
+			function = "spifi";
+			bias-disable;
+		};
+	};
+
+	ssp1_pins: ssp1-pins {
+		ssp1_sck_cfg {
+			pins = "pf_4";
+			function = "ssp1";
+			slew-rate = <1>;
+			bias-pull-down;
+		};
+
+		ssp1_miso_cfg {
+			pins = "pf_6";
+			function = "ssp1";
+			input-enable;
+			input-schmitt-disable;
+			slew-rate = <1>;
+			bias-pull-down;
+		};
+
+		ssp1_mosi_cfg {
+			pins = "pf_7";
+			function = "ssp1";
+			slew-rate = <1>;
+			bias-pull-down;
+		};
+
+		ssp1_ssel_cfg {
+			pins = "pf_5";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	uart0_pins: uart0-pins {
+		uart0_rxd_cfg {
+			pins = "pf_11";
+			function = "uart0";
+			input-enable;
+			input-schmitt-disable;
+			bias-disable;
+		};
+
+		uart0_clk_dir_txd_cfg {
+			pins = "pf_8", "pf_9", "pf_10";
+			function = "uart0";
+			bias-pull-down;
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		uart1_rxd_cfg {
+			pins = "pc_14";
+			function = "uart1";
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		uart1_dtr_txd_cfg {
+			pins = "pc_12", "pc_13";
+			function = "uart1";
+			bias-pull-down;
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		uart2_rxd_cfg {
+			pins = "pa_2";
+			function = "uart2";
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		uart2_txd_cfg {
+			pins = "pa_1";
+			function = "uart2";
+			bias-pull-down;
+		};
+	};
+
+	uart3_pins: uart3-pins {
+		uart3_rx_cfg {
+			pins = "p2_4";
+			function = "uart3";
+			bias-disable;
+			input-enable;
+			input-schmitt-disable;
+		};
+
+		uart3_tx_cfg {
+			pins = "p2_3";
+			function = "uart3";
+			bias-pull-down;
+		};
+	};
+
+	usb0_pins: usb0-pins {
+		usb0_pwr_enable_cfg {
+			pins = "p6_3";
+			function = "usb0";
+		};
+
+		usb0_pwr_fault_cfg {
+			pins = "p8_0";
+			function = "usb0";
+			bias-disable;
+			input-enable;
+		};
+	};
+};
+
+&adc1 {
+	status = "okay";
+	vref-supply = <&vcc>;
+};
+
+&can0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&can0_pins>;
+};
+
+/* Pin conflict with EMC, muxed by JP5 and JP6 */
+&can1 {
+	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&can1_pins>;
+};
+
+&emc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&emc_pins>;
+
+	cs0 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges;
+
+		mpmc,cs = <0>;
+		mpmc,memory-width = <16>;
+		mpmc,byte-lane-low;
+		mpmc,write-enable-delay = <0>;
+		mpmc,output-enable-delay = <0>;
+		mpmc,read-access-delay = <70>;
+		mpmc,page-mode-read-delay = <70>;
+
+		/* SST/Microchip SST39VF1601 */
+		flash@0,0 {
+			compatible = "cfi-flash";
+			reg = <0 0 0x400000>;
+			bank-width = <2>;
+		};
+	};
+};
+
+&enet_tx_clk {
+	clock-frequency = <50000000>;
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <400000>;
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <400000>;
+
+	sensor@49 {
+		compatible = "national,lm75";
+		reg = <0x49>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c512";
+		reg = <0x50>;
+	};
+};
+
+&lcdc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcd_pins>;
+
+	max-memory-bandwidth = <92240000>;
+
+	port {
+		lcdc_output: endpoint {
+			remote-endpoint = <&panel_input>;
+			arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
+		};
+	};
+};
+
+&mac {
+	status = "okay";
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&enet_rmii_pins>;
+	phy-handle = <&phy1>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy1: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
+};
+
+&mmcsd {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_pins>;
+	bus-width = <4>;
+	vmmc-supply = <&vmmc>;
+};
+
+/* Pin conflict with SSP0, the latter is routed to J17 pin header */
+&spifi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spifi_pins>;
+
+	/* Atmel AT25DF321A */
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <51000000>;
+		spi-cpol;
+		spi-cpha;
+	};
+};
+
+&ssp1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ssp1_pins>;
+	num-cs = <1>;
+	cs-gpios = <&gpio LPC_GPIO(7,19) GPIO_ACTIVE_LOW>;
+};
+
+/* Routed to J17 pin header */
+&uart0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+};
+
+/* RS485 */
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+};
+
+/* Routed to J17 pin header */
+&uart2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
+
+&usb0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_pins>;
+};

linux-7.2.3/arch/arm/boot/dts/nxp/lpc/lpc4357.dtsi

@@ -0,0 +1,52 @@
+/*
+ * NXP LPC435x, LPC433x, LPC4327, LPC4325, LPC4317 and LPC4315 SoC
+ *
+ * Copyright 2015 Joachim Eastwood <manabian@gmail.com>
+ *
+ * This code is released using a dual license strategy: BSD/GPL
+ * You can choose the licence that better fits your requirements.
+ *
+ * Released under the terms of 3-clause BSD License
+ * Released under the terms of GNU General Public License Version 2.0
+ *
+ */
+
+/ {
+	compatible = "nxp,lpc4357";
+
+	cpus {
+		cpu@0 {
+			compatible = "arm,cortex-m4";
+		};
+	};
+
+	soc {
+		sram0: sram@10000000 {
+			compatible = "mmio-sram";
+			reg = <0x10000000 0x8000>; /* 32 KiB local SRAM */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+		};
+
+		sram1: sram@10080000 {
+			compatible = "mmio-sram";
+			reg = <0x10080000 0xa000>; /* 32 + 8 KiB local SRAM */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+		};
+
+		sram2: sram@20000000 {
+			compatible = "mmio-sram";
+			reg = <0x20000000 0x10000>; /* 4 x 16 KiB AHB SRAM */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+		};
+	};
+};
+
+&eeprom {
+	status = "okay";
+};