Resguardo inicial

linux-7.2.3/arch/arm/mach-sa1100/include/mach/assabet.h

@@ -0,0 +1,99 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * arch/arm/mach-sa1100/include/mach/assabet.h
+ *
+ * Created 2000/06/05 by Nicolas Pitre <nico@fluxnic.net>
+ *
+ * This file contains the hardware specific definitions for Assabet
+ * Only include this file from SA1100-specific files.
+ *
+ * 2000/05/23 John Dorsey <john+@cs.cmu.edu>
+ *      Definitions for Neponset added.
+ */
+#ifndef __ASM_ARCH_ASSABET_H
+#define __ASM_ARCH_ASSABET_H
+
+
+/* System Configuration Register flags */
+
+#define ASSABET_SCR_SDRAM_LOW	(1<<2)	/* SDRAM size (low bit) */
+#define ASSABET_SCR_SDRAM_HIGH	(1<<3)	/* SDRAM size (high bit) */
+#define ASSABET_SCR_FLASH_LOW	(1<<4)	/* Flash size (low bit) */
+#define ASSABET_SCR_FLASH_HIGH	(1<<5)	/* Flash size (high bit) */
+#define ASSABET_SCR_GFX		(1<<8)	/* Graphics Accelerator (0 = present) */
+#define ASSABET_SCR_SA1111	(1<<9)	/* Neponset (0 = present) */
+
+#define ASSABET_SCR_INIT	-1
+
+extern unsigned long SCR_value;
+
+#ifdef CONFIG_ASSABET_NEPONSET
+#define machine_has_neponset()  ((SCR_value & ASSABET_SCR_SA1111) == 0)
+#else
+#define machine_has_neponset()	(0)
+#endif
+
+/* Board Control Register */
+
+#define ASSABET_BCR_BASE  0xf1000000
+#define ASSABET_BCR (*(volatile unsigned int *)(ASSABET_BCR_BASE))
+
+#define ASSABET_BCR_CF_PWR	(1<<0)	/* Compact Flash Power (1 = 3.3v, 0 = off) */
+#define ASSABET_BCR_CF_RST	(1<<1)	/* Compact Flash Reset (1 = power up reset) */
+#define ASSABET_BCR_NGFX_RST	(1<<1)	/* Graphics Accelerator Reset (0 = hold reset) */
+#define ASSABET_BCR_NCODEC_RST	(1<<2)	/* 0 = Holds UCB1300, ADI7171, and UDA1341 in reset */
+#define ASSABET_BCR_IRDA_FSEL	(1<<3)	/* IRDA Frequency select (0 = SIR, 1 = MIR/ FIR) */
+#define ASSABET_BCR_IRDA_MD0	(1<<4)	/* Range/Power select */
+#define ASSABET_BCR_IRDA_MD1	(1<<5)	/* Range/Power select */
+#define ASSABET_BCR_STEREO_LB	(1<<6)	/* Stereo Loopback */
+#define ASSABET_BCR_CF_BUS_OFF	(1<<7)	/* Compact Flash bus (0 = on, 1 = off (float)) */
+#define ASSABET_BCR_AUDIO_ON	(1<<8)	/* Audio power on */
+#define ASSABET_BCR_LIGHT_ON	(1<<9)	/* Backlight */
+#define ASSABET_BCR_LCD_12RGB	(1<<10)	/* 0 = 16RGB, 1 = 12RGB */
+#define ASSABET_BCR_LCD_ON	(1<<11)	/* LCD power on */
+#define ASSABET_BCR_RS232EN	(1<<12)	/* RS232 transceiver enable */
+#define ASSABET_BCR_LED_RED	(1<<13)	/* D9 (0 = on, 1 = off) */
+#define ASSABET_BCR_LED_GREEN	(1<<14)	/* D8 (0 = on, 1 = off) */
+#define ASSABET_BCR_VIB_ON	(1<<15)	/* Vibration motor (quiet alert) */
+#define ASSABET_BCR_COM_DTR	(1<<16)	/* COMport Data Terminal Ready */
+#define ASSABET_BCR_COM_RTS	(1<<17)	/* COMport Request To Send */
+#define ASSABET_BCR_RAD_WU	(1<<18)	/* Radio wake up interrupt */
+#define ASSABET_BCR_SMB_EN	(1<<19)	/* System management bus enable */
+#define ASSABET_BCR_TV_IR_DEC	(1<<20)	/* TV IR Decode Enable (not implemented) */
+#define ASSABET_BCR_QMUTE	(1<<21)	/* Quick Mute */
+#define ASSABET_BCR_RAD_ON	(1<<22)	/* Radio Power On */
+#define ASSABET_BCR_SPK_OFF	(1<<23)	/* 1 = Speaker amplifier power off */
+
+#ifdef CONFIG_SA1100_ASSABET
+extern void ASSABET_BCR_frob(unsigned int mask, unsigned int set);
+#else
+#define ASSABET_BCR_frob(x,y)	do { } while (0)
+#endif
+
+extern void assabet_uda1341_reset(int set);
+
+#define ASSABET_BCR_set(x)	ASSABET_BCR_frob((x), (x))
+#define ASSABET_BCR_clear(x)	ASSABET_BCR_frob((x), 0)
+
+#define ASSABET_BSR_BASE	0xf1000000
+#define ASSABET_BSR (*(volatile unsigned int*)(ASSABET_BSR_BASE))
+
+#define ASSABET_BSR_RS232_VALID	(1 << 24)
+#define ASSABET_BSR_COM_DCD	(1 << 25)
+#define ASSABET_BSR_COM_CTS	(1 << 26)
+#define ASSABET_BSR_COM_DSR	(1 << 27)
+#define ASSABET_BSR_RAD_CTS	(1 << 28)
+#define ASSABET_BSR_RAD_DSR	(1 << 29)
+#define ASSABET_BSR_RAD_DCD	(1 << 30)
+#define ASSABET_BSR_RAD_RI	(1 << 31)
+
+
+/* GPIOs (bitmasks) for which the generic definition doesn't say much */
+#define ASSABET_GPIO_RADIO_IRQ		GPIO_GPIO (14)	/* Radio interrupt request  */
+#define ASSABET_GPIO_PS_MODE_SYNC	GPIO_GPIO (16)	/* Power supply mode/sync   */
+#define ASSABET_GPIO_STEREO_64FS_CLK	GPIO_GPIO (19)	/* SSP UDA1341 clock input  */
+#define ASSABET_GPIO_GFX_IRQ		GPIO_GPIO (24)	/* Graphics IRQ */
+#define ASSABET_GPIO_BATT_LOW		GPIO_GPIO (26)	/* Low battery */
+#define ASSABET_GPIO_RCLK		GPIO_GPIO (26)	/* CCLK/2  */
+
+#endif

linux-7.2.3/arch/arm/mach-sa1100/include/mach/bitfield.h

@@ -0,0 +1,113 @@
+/*
+ *	FILE    	bitfield.h
+ *
+ *	Version 	1.1
+ *	Author  	Copyright (c) Marc A. Viredaz, 1998
+ *	        	DEC Western Research Laboratory, Palo Alto, CA
+ *	Date    	April 1998 (April 1997)
+ *	System  	Advanced RISC Machine (ARM)
+ *	Language	C or ARM Assembly
+ *	Purpose 	Definition of macros to operate on bit fields.
+ */
+
+
+
+#ifndef __BITFIELD_H
+#define __BITFIELD_H
+
+#ifndef __ASSEMBLY__
+#define UData(Data)	((unsigned long) (Data))
+#else
+#define UData(Data)	(Data)
+#endif
+
+
+/*
+ * MACRO: Fld
+ *
+ * Purpose
+ *    The macro "Fld" encodes a bit field, given its size and its shift value
+ *    with respect to bit 0.
+ *
+ * Note
+ *    A more intuitive way to encode bit fields would have been to use their
+ *    mask. However, extracting size and shift value information from a bit
+ *    field's mask is cumbersome and might break the assembler (255-character
+ *    line-size limit).
+ *
+ * Input
+ *    Size      	Size of the bit field, in number of bits.
+ *    Shft      	Shift value of the bit field with respect to bit 0.
+ *
+ * Output
+ *    Fld       	Encoded bit field.
+ */
+
+#define Fld(Size, Shft)	(((Size) << 16) + (Shft))
+
+
+/*
+ * MACROS: FSize, FShft, FMsk, FAlnMsk, F1stBit
+ *
+ * Purpose
+ *    The macros "FSize", "FShft", "FMsk", "FAlnMsk", and "F1stBit" return
+ *    the size, shift value, mask, aligned mask, and first bit of a
+ *    bit field.
+ *
+ * Input
+ *    Field     	Encoded bit field (using the macro "Fld").
+ *
+ * Output
+ *    FSize     	Size of the bit field, in number of bits.
+ *    FShft     	Shift value of the bit field with respect to bit 0.
+ *    FMsk      	Mask for the bit field.
+ *    FAlnMsk   	Mask for the bit field, aligned on bit 0.
+ *    F1stBit   	First bit of the bit field.
+ */
+
+#define FSize(Field)	((Field) >> 16)
+#define FShft(Field)	((Field) & 0x0000FFFF)
+#define FMsk(Field)	(((UData (1) << FSize (Field)) - 1) << FShft (Field))
+#define FAlnMsk(Field)	((UData (1) << FSize (Field)) - 1)
+#define F1stBit(Field)	(UData (1) << FShft (Field))
+
+
+/*
+ * MACRO: FInsrt
+ *
+ * Purpose
+ *    The macro "FInsrt" inserts a value into a bit field by shifting the
+ *    former appropriately.
+ *
+ * Input
+ *    Value     	Bit-field value.
+ *    Field     	Encoded bit field (using the macro "Fld").
+ *
+ * Output
+ *    FInsrt    	Bit-field value positioned appropriately.
+ */
+
+#define FInsrt(Value, Field) \
+                	(UData (Value) << FShft (Field))
+
+
+/*
+ * MACRO: FExtr
+ *
+ * Purpose
+ *    The macro "FExtr" extracts the value of a bit field by masking and
+ *    shifting it appropriately.
+ *
+ * Input
+ *    Data      	Data containing the bit-field to be extracted.
+ *    Field     	Encoded bit field (using the macro "Fld").
+ *
+ * Output
+ *    FExtr     	Bit-field value.
+ */
+
+#define FExtr(Data, Field) \
+                	((UData (Data) >> FShft (Field)) & FAlnMsk (Field))
+
+
+#endif /* __BITFIELD_H */

linux-7.2.3/arch/arm/mach-sa1100/include/mach/collie.h

@@ -0,0 +1,94 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * arch/arm/mach-sa1100/include/mach/collie.h
+ *
+ * This file contains the hardware specific definitions for Collie
+ * Only include this file from SA1100-specific files.
+ *
+ * ChangeLog:
+ *   04-06-2001 Lineo Japan, Inc.
+ *   04-16-2001 SHARP Corporation
+ *   07-07-2002 Chris Larson <clarson@digi.com>
+ *
+ */
+#ifndef __ASM_ARCH_COLLIE_H
+#define __ASM_ARCH_COLLIE_H
+
+#include "hardware.h" /* Gives GPIO_MAX */
+
+#define COLLIE_SCOOP_GPIO_BASE	(GPIO_MAX + 1)
+#define COLLIE_GPIO_CHARGE_ON	(COLLIE_SCOOP_GPIO_BASE + 0)
+#define COLLIE_SCP_DIAG_BOOT1	SCOOP_GPCR_PA12
+#define COLLIE_SCP_DIAG_BOOT2	SCOOP_GPCR_PA13
+#define COLLIE_SCP_MUTE_L	SCOOP_GPCR_PA14
+#define COLLIE_SCP_MUTE_R	SCOOP_GPCR_PA15
+#define COLLIE_SCP_5VON		SCOOP_GPCR_PA16
+#define COLLIE_SCP_AMP_ON	SCOOP_GPCR_PA17
+#define COLLIE_GPIO_VPEN	(COLLIE_SCOOP_GPIO_BASE + 7)
+#define COLLIE_SCP_LB_VOL_CHG	SCOOP_GPCR_PA19
+
+#define COLLIE_SCOOP_IO_DIR	(COLLIE_SCP_MUTE_L | COLLIE_SCP_MUTE_R | \
+				COLLIE_SCP_5VON | COLLIE_SCP_AMP_ON | \
+				COLLIE_SCP_LB_VOL_CHG)
+#define COLLIE_SCOOP_IO_OUT	(COLLIE_SCP_MUTE_L | COLLIE_SCP_MUTE_R)
+
+/* GPIOs for gpiolib  */
+
+#define COLLIE_GPIO_ON_KEY		(0)
+#define COLLIE_GPIO_AC_IN		(1)
+#define COLLIE_GPIO_SDIO_INT		(11)
+#define COLLIE_GPIO_CF_IRQ		(14)
+#define COLLIE_GPIO_nREMOCON_INT	(15)
+#define COLLIE_GPIO_UCB1x00_RESET	(16)
+#define COLLIE_GPIO_nMIC_ON		(17)
+#define COLLIE_GPIO_nREMOCON_ON		(18)
+#define COLLIE_GPIO_CO			(20)
+#define COLLIE_GPIO_MCP_CLK		(21)
+#define COLLIE_GPIO_CF_CD		(22)
+#define COLLIE_GPIO_UCB1x00_IRQ		(23)
+#define COLLIE_GPIO_WAKEUP		(24)
+#define COLLIE_GPIO_GA_INT		(25)
+#define COLLIE_GPIO_MAIN_BAT_LOW	(26)
+
+/* GPIO definitions for direct register access */
+
+#define _COLLIE_GPIO_ON_KEY		GPIO_GPIO(0)
+#define _COLLIE_GPIO_AC_IN		GPIO_GPIO(1)
+#define _COLLIE_GPIO_nREMOCON_INT	GPIO_GPIO(15)
+#define _COLLIE_GPIO_UCB1x00_RESET	GPIO_GPIO(16)
+#define _COLLIE_GPIO_nMIC_ON		GPIO_GPIO(17)
+#define _COLLIE_GPIO_nREMOCON_ON	GPIO_GPIO(18)
+#define _COLLIE_GPIO_CO			GPIO_GPIO(20)
+#define _COLLIE_GPIO_WAKEUP		GPIO_GPIO(24)
+/* Interrupts */
+
+#define COLLIE_IRQ_GPIO_ON_KEY		IRQ_GPIO0
+#define COLLIE_IRQ_GPIO_AC_IN		IRQ_GPIO1
+#define COLLIE_IRQ_GPIO_SDIO_IRQ	IRQ_GPIO11
+#define COLLIE_IRQ_GPIO_CF_IRQ		IRQ_GPIO14
+#define COLLIE_IRQ_GPIO_nREMOCON_INT	IRQ_GPIO15
+#define COLLIE_IRQ_GPIO_CO		IRQ_GPIO20
+#define COLLIE_IRQ_GPIO_CF_CD		IRQ_GPIO22
+#define COLLIE_IRQ_GPIO_UCB1x00_IRQ	IRQ_GPIO23
+#define COLLIE_IRQ_GPIO_WAKEUP		IRQ_GPIO24
+#define COLLIE_IRQ_GPIO_GA_INT		IRQ_GPIO25
+#define COLLIE_IRQ_GPIO_MAIN_BAT_LOW	IRQ_GPIO26
+
+/* GPIO's on the TC35143AF (Toshiba Analog Frontend) */
+#define COLLIE_TC35143_GPIO_BASE	(GPIO_MAX + 13)
+#define COLLIE_TC35143_GPIO_VERSION0    UCB_IO_0
+#define COLLIE_TC35143_GPIO_TBL_CHK     UCB_IO_1
+#define COLLIE_TC35143_GPIO_VPEN_ON     UCB_IO_2
+#define COLLIE_GPIO_IR_ON		(COLLIE_TC35143_GPIO_BASE + 3)
+#define COLLIE_TC35143_GPIO_AMP_ON      UCB_IO_4
+#define COLLIE_TC35143_GPIO_VERSION1    UCB_IO_5
+#define COLLIE_TC35143_GPIO_FS8KLPF     UCB_IO_5
+#define COLLIE_TC35143_GPIO_BUZZER_BIAS UCB_IO_6
+#define COLLIE_GPIO_MBAT_ON     	(COLLIE_TC35143_GPIO_BASE + 7)
+#define COLLIE_GPIO_BBAT_ON     	(COLLIE_TC35143_GPIO_BASE + 8)
+#define COLLIE_GPIO_TMP_ON      	(COLLIE_TC35143_GPIO_BASE + 9)
+#define COLLIE_TC35143_GPIO_IN		(UCB_IO_0 | UCB_IO_2 | UCB_IO_5)
+#define COLLIE_TC35143_GPIO_OUT		(UCB_IO_1 | UCB_IO_3 | UCB_IO_4 \
+						| UCB_IO_6)
+
+#endif

linux-7.2.3/arch/arm/mach-sa1100/include/mach/generic.h

@@ -0,0 +1 @@
+#include "../../generic.h"

linux-7.2.3/arch/arm/mach-sa1100/include/mach/h3xxx.h

@@ -0,0 +1,81 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Definitions for Compaq iPAQ H3100 and H3600 handheld computers
+ *
+ * (c) 2000 Compaq Computer Corporation. (Author: Jamey Hicks)
+ * (c) 2009 Dmitry Artamonow <mad_soft@inbox.ru>
+ */
+
+#ifndef _INCLUDE_H3XXX_H_
+#define _INCLUDE_H3XXX_H_
+
+#include "hardware.h" /* Gives GPIO_MAX */
+
+/* Physical memory regions corresponding to chip selects */
+#define H3600_EGPIO_PHYS	(SA1100_CS5_PHYS + 0x01000000)
+#define H3600_BANK_2_PHYS	SA1100_CS2_PHYS
+#define H3600_BANK_4_PHYS	SA1100_CS4_PHYS
+
+/* Virtual memory regions corresponding to chip selects 2 & 4 (used on sleeves) */
+#define H3600_EGPIO_VIRT	0xf0000000
+#define H3600_BANK_2_VIRT	0xf1000000
+#define H3600_BANK_4_VIRT	0xf3800000
+
+/*
+ * gpiolib numbers for all iPAQs
+ */
+#define H3XXX_GPIO_PWR_BUTTON		0
+#define H3XXX_GPIO_PCMCIA_CD1		10
+#define H3XXX_GPIO_PCMCIA_IRQ1		11
+#define H3XXX_GPIO_PCMCIA_CD0		17
+#define H3XXX_GPIO_ACTION_BUTTON	18
+#define H3XXX_GPIO_SYS_CLK		19
+#define H3XXX_GPIO_PCMCIA_IRQ0		21
+#define H3XXX_GPIO_COM_DCD		23
+#define H3XXX_GPIO_OPTION		24
+#define H3XXX_GPIO_COM_CTS		25
+#define H3XXX_GPIO_COM_RTS		26
+
+/* machine-specific gpios */
+
+#define H3100_GPIO_BT_ON		2
+#define H3100_GPIO_QMUTE		4
+#define H3100_GPIO_LCD_3V_ON		5
+#define H3100_GPIO_AUD_ON		6
+#define H3100_GPIO_AUD_PWR_ON		7
+#define H3100_GPIO_IR_ON		8
+#define H3100_GPIO_IR_FSEL		9
+
+#define H3600_GPIO_CLK_SET0		12	/* audio sample rate clock generator */
+#define H3600_GPIO_CLK_SET1		13
+#define H3600_GPIO_SOFT_RESET		20	/* also known as BATT_FAULT */
+#define H3600_GPIO_OPT_LOCK		22
+#define H3600_GPIO_OPT_DET		27
+
+
+/* H3100 / 3600 EGPIO pins */
+#define H3XXX_EGPIO_BASE		(GPIO_MAX + 1)
+
+#define H3XXX_EGPIO_VPP_ON		(H3XXX_EGPIO_BASE + 0)
+#define H3XXX_EGPIO_CARD_RESET		(H3XXX_EGPIO_BASE + 1) /* reset the attached pcmcia/compactflash card.  active high. */
+#define H3XXX_EGPIO_OPT_RESET		(H3XXX_EGPIO_BASE + 2) /* reset the attached option pack.  active high. */
+#define H3XXX_EGPIO_CODEC_NRESET	(H3XXX_EGPIO_BASE + 3) /* reset the onboard UDA1341.  active low. */
+#define H3XXX_EGPIO_OPT_NVRAM_ON	(H3XXX_EGPIO_BASE + 4) /* apply power to optionpack nvram, active high. */
+#define H3XXX_EGPIO_OPT_ON		(H3XXX_EGPIO_BASE + 5) /* full power to option pack.  active high. */
+#define H3XXX_EGPIO_LCD_ON		(H3XXX_EGPIO_BASE + 6) /* enable 3.3V to LCD.  active high. */
+#define H3XXX_EGPIO_RS232_ON		(H3XXX_EGPIO_BASE + 7) /* UART3 transceiver force on.  Active high. */
+
+/* H3600 only EGPIO pins */
+#define H3600_EGPIO_LCD_PCI		(H3XXX_EGPIO_BASE + 8) /* LCD control IC enable.  active high. */
+#define H3600_EGPIO_IR_ON		(H3XXX_EGPIO_BASE + 9) /* apply power to IR module.  active high. */
+#define H3600_EGPIO_AUD_AMP_ON		(H3XXX_EGPIO_BASE + 10) /* apply power to audio power amp.  active high. */
+#define H3600_EGPIO_AUD_PWR_ON		(H3XXX_EGPIO_BASE + 11) /* apply power to reset of audio circuit.  active high. */
+#define H3600_EGPIO_QMUTE		(H3XXX_EGPIO_BASE + 12) /* mute control for onboard UDA1341.  active high. */
+#define H3600_EGPIO_IR_FSEL		(H3XXX_EGPIO_BASE + 13) /* IR speed select: 1->fast, 0->slow */
+#define H3600_EGPIO_LCD_5V_ON		(H3XXX_EGPIO_BASE + 14) /* enable 5V to LCD. active high. */
+#define H3600_EGPIO_LVDD_ON		(H3XXX_EGPIO_BASE + 15) /* enable 9V and -6.5V to LCD. */
+
+void __init h3xxx_map_io(void);
+void __init h3xxx_mach_init(void);
+
+#endif /* _INCLUDE_H3XXX_H_ */

linux-7.2.3/arch/arm/mach-sa1100/include/mach/hardware.h

@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * arch/arm/mach-sa1100/include/mach/hardware.h
+ *
+ * Copyright (C) 1998 Nicolas Pitre <nico@fluxnic.net>
+ *
+ * This file contains the hardware definitions for SA1100 architecture
+ *
+ * 2000/05/23 John Dorsey <john+@cs.cmu.edu>
+ *      Definitions for SA1111 added.
+ */
+
+#ifndef __ASM_ARCH_HARDWARE_H
+#define __ASM_ARCH_HARDWARE_H
+
+
+#define UNCACHEABLE_ADDR	0xfa050000	/* ICIP */
+
+
+/*
+ * SA1100 internal I/O mappings
+ *
+ * We have the following mapping:
+ *      phys            virt
+ *      80000000        f8000000
+ *      90000000        fa000000
+ *      a0000000        fc000000
+ *      b0000000        fe000000
+ */
+
+#define VIO_BASE        0xf8000000	/* virtual start of IO space */
+#define VIO_SHIFT       3		/* x = IO space shrink power */
+#define PIO_START       0x80000000	/* physical start of IO space */
+
+#define io_p2v( x )             \
+   IOMEM( (((x)&0x00ffffff) | (((x)&0x30000000)>>VIO_SHIFT)) + VIO_BASE )
+#define io_v2p( x )             \
+   ( (((x)&0x00ffffff) | (((x)&(0x30000000>>VIO_SHIFT))<<VIO_SHIFT)) + PIO_START )
+
+#define __MREG(x)	IOMEM(io_p2v(x))
+
+#ifndef __ASSEMBLY__
+
+# define __REG(x)	(*((volatile unsigned long __iomem *)io_p2v(x)))
+# define __PREG(x)	(io_v2p((unsigned long)&(x)))
+
+#else
+
+# define __REG(x)	io_p2v(x)
+# define __PREG(x)	io_v2p(x)
+
+#endif
+
+#include "SA-1100.h"
+
+#endif  /* _ASM_ARCH_HARDWARE_H */

linux-7.2.3/arch/arm/mach-sa1100/include/mach/irqs.h

@@ -0,0 +1,101 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * arch/arm/mach-sa1100/include/mach/irqs.h
+ *
+ * Copyright (C) 1996 Russell King
+ * Copyright (C) 1998 Deborah Wallach (updates for SA1100/Brutus).
+ * Copyright (C) 1999 Nicolas Pitre (full GPIO irq isolation)
+ *
+ * 2001/11/14	RMK	Cleaned up and standardised a lot of the IRQs.
+ */
+
+#define	IRQ_GPIO0_SC		1
+#define	IRQ_GPIO1_SC		2
+#define	IRQ_GPIO2_SC		3
+#define	IRQ_GPIO3_SC		4
+#define	IRQ_GPIO4_SC		5
+#define	IRQ_GPIO5_SC		6
+#define	IRQ_GPIO6_SC		7
+#define	IRQ_GPIO7_SC		8
+#define	IRQ_GPIO8_SC		9
+#define	IRQ_GPIO9_SC		10
+#define	IRQ_GPIO10_SC		11
+#define	IRQ_GPIO11_27		12
+#define	IRQ_LCD			13	/* LCD controller           */
+#define	IRQ_Ser0UDC		14	/* Ser. port 0 UDC          */
+#define	IRQ_Ser1SDLC		15	/* Ser. port 1 SDLC         */
+#define	IRQ_Ser1UART		16	/* Ser. port 1 UART         */
+#define	IRQ_Ser2ICP		17	/* Ser. port 2 ICP          */
+#define	IRQ_Ser3UART		18	/* Ser. port 3 UART         */
+#define	IRQ_Ser4MCP		19	/* Ser. port 4 MCP          */
+#define	IRQ_Ser4SSP		20	/* Ser. port 4 SSP          */
+#define	IRQ_DMA0		21	/* DMA controller channel 0 */
+#define	IRQ_DMA1		22	/* DMA controller channel 1 */
+#define	IRQ_DMA2		23	/* DMA controller channel 2 */
+#define	IRQ_DMA3		24	/* DMA controller channel 3 */
+#define	IRQ_DMA4		25	/* DMA controller channel 4 */
+#define	IRQ_DMA5		26	/* DMA controller channel 5 */
+#define	IRQ_OST0		27	/* OS Timer match 0         */
+#define	IRQ_OST1		28	/* OS Timer match 1         */
+#define	IRQ_OST2		29	/* OS Timer match 2         */
+#define	IRQ_OST3		30	/* OS Timer match 3         */
+#define	IRQ_RTC1Hz		31	/* RTC 1 Hz clock           */
+#define	IRQ_RTCAlrm		32	/* RTC Alarm                */
+
+#define	IRQ_GPIO0		33
+#define	IRQ_GPIO1		34
+#define	IRQ_GPIO2		35
+#define	IRQ_GPIO3		36
+#define	IRQ_GPIO4		37
+#define	IRQ_GPIO5		38
+#define	IRQ_GPIO6		39
+#define	IRQ_GPIO7		40
+#define	IRQ_GPIO8		41
+#define	IRQ_GPIO9		42
+#define	IRQ_GPIO10		43
+#define	IRQ_GPIO11		44
+#define	IRQ_GPIO12		45
+#define	IRQ_GPIO13		46
+#define	IRQ_GPIO14		47
+#define	IRQ_GPIO15		48
+#define	IRQ_GPIO16		49
+#define	IRQ_GPIO17		50
+#define	IRQ_GPIO18		51
+#define	IRQ_GPIO19		52
+#define	IRQ_GPIO20		53
+#define	IRQ_GPIO21		54
+#define	IRQ_GPIO22		55
+#define	IRQ_GPIO23		56
+#define	IRQ_GPIO24		57
+#define	IRQ_GPIO25		58
+#define	IRQ_GPIO26		59
+#define	IRQ_GPIO27		60
+
+/*
+ * The next 16 interrupts are for board specific purposes.  Since
+ * the kernel can only run on one machine at a time, we can re-use
+ * these.  If you need more, increase IRQ_BOARD_END, but keep it
+ * within sensible limits.  IRQs 61 to 76 are available.
+ */
+#define IRQ_BOARD_START		61
+#define IRQ_BOARD_END		77
+
+/*
+ * Figure out the MAX IRQ number.
+ *
+ * Neponset, SA1111 and UCB1x00 are sparse IRQ aware, so can dynamically
+ * allocate their IRQs above NR_IRQS.
+ *
+ * LoCoMo has 4 additional IRQs, but is not sparse IRQ aware, and so has
+ * to be included in the NR_IRQS calculation.
+ */
+#ifdef CONFIG_SHARP_LOCOMO
+#define NR_IRQS_LOCOMO		4
+#else
+#define NR_IRQS_LOCOMO		0
+#endif
+
+#ifndef NR_IRQS
+#define NR_IRQS (IRQ_BOARD_START + NR_IRQS_LOCOMO)
+#endif
+#define SA1100_NR_IRQS (IRQ_BOARD_START + NR_IRQS_LOCOMO)

linux-7.2.3/arch/arm/mach-sa1100/include/mach/jornada720.h

@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * arch/arm/mach-sa1100/include/mach/jornada720.h
+ *
+ * SSP/MCU communication definitions for HP Jornada 710/720/728
+ *
+ * Copyright 2007,2008 Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
+ *  Copyright 2000 John Ankcorn <jca@lcs.mit.edu>
+ */
+
+ /* HP Jornada 7xx microprocessor commands */
+#define GETBATTERYDATA		0xc0
+#define GETSCANKEYCODE		0x90
+#define GETTOUCHSAMPLES		0xa0
+#define GETCONTRAST		0xD0
+#define SETCONTRAST		0xD1
+#define GETBRIGHTNESS		0xD2
+#define SETBRIGHTNESS		0xD3
+#define CONTRASTOFF		0xD8
+#define BRIGHTNESSOFF		0xD9
+#define PWMOFF			0xDF
+#define TXDUMMY			0x11
+#define ERRORCODE		0x00
+
+extern void jornada_ssp_start(void);
+extern void jornada_ssp_end(void);
+extern int jornada_ssp_inout(u8 byte);
+extern int jornada_ssp_byte(u8 byte);

linux-7.2.3/arch/arm/mach-sa1100/include/mach/memory.h

@@ -0,0 +1,37 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * arch/arm/mach-sa1100/include/mach/memory.h
+ *
+ * Copyright (C) 1999-2000 Nicolas Pitre <nico@fluxnic.net>
+ */
+
+#ifndef __ASM_ARCH_MEMORY_H
+#define __ASM_ARCH_MEMORY_H
+
+#include <linux/sizes.h>
+
+/*
+ * Because of the wide memory address space between physical RAM banks on the
+ * SA1100, it's much convenient to use Linux's SparseMEM support to implement
+ * our memory map representation.  Assuming all memory nodes have equal access
+ * characteristics, we then have generic discontiguous memory support.
+ *
+ * The sparsemem banks are matched with the physical memory bank addresses
+ * which are incidentally the same as virtual addresses.
+ * 
+ * 	node 0:  0xc0000000 - 0xc7ffffff
+ * 	node 1:  0xc8000000 - 0xcfffffff
+ * 	node 2:  0xd0000000 - 0xd7ffffff
+ * 	node 3:  0xd8000000 - 0xdfffffff
+ */
+#define MAX_PHYSMEM_BITS	32
+#define SECTION_SIZE_BITS	27
+
+/*
+ * Cache flushing area - SA1100 zero bank
+ */
+#define FLUSH_BASE_PHYS		0xe0000000
+#define FLUSH_BASE		0xf5000000
+#define FLUSH_BASE_MINICACHE	0xf5100000
+
+#endif

linux-7.2.3/arch/arm/mach-sa1100/include/mach/mtd-xip.h

@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * MTD primitives for XIP support. Architecture specific functions
+ *
+ * Do not include this file directly. It's included from linux/mtd/xip.h
+ * 
+ * Author:	Nicolas Pitre
+ * Created:	Nov 2, 2004
+ * Copyright:	(C) 2004 MontaVista Software, Inc.
+ */
+
+#ifndef __ARCH_SA1100_MTD_XIP_H__
+#define __ARCH_SA1100_MTD_XIP_H__
+
+#include <mach/hardware.h>
+
+#define xip_irqpending()	(ICIP & ICMR)
+
+/* we sample OSCR and convert desired delta to usec (1/4 ~= 1000000/3686400) */
+#define xip_currtime()		readl_relaxed(OSCR)
+#define xip_elapsed_since(x)	(signed)((readl_relaxed(OSCR) - (x)) / 4)
+
+#endif /* __ARCH_SA1100_MTD_XIP_H__ */

linux-7.2.3/arch/arm/mach-sa1100/include/mach/neponset.h

@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * arch/arm/mach-sa1100/include/mach/neponset.h
+ *
+ * Created 2000/06/05 by Nicolas Pitre <nico@fluxnic.net>
+ *
+ * This file contains the hardware specific definitions for Assabet
+ * Only include this file from SA1100-specific files.
+ *
+ * 2000/05/23 John Dorsey <john+@cs.cmu.edu>
+ *      Definitions for Neponset added.
+ */
+#ifndef __ASM_ARCH_NEPONSET_H
+#define __ASM_ARCH_NEPONSET_H
+
+/*
+ * Neponset definitions: 
+ */
+#define NCR_GP01_OFF		(1<<0)
+#define NCR_TP_PWR_EN		(1<<1)
+#define NCR_MS_PWR_EN		(1<<2)
+#define NCR_ENET_OSC_EN		(1<<3)
+#define NCR_SPI_KB_WK_UP	(1<<4)
+#define NCR_A0VPP		(1<<5)
+#define NCR_A1VPP		(1<<6)
+
+void neponset_ncr_frob(unsigned int, unsigned int);
+#define neponset_ncr_set(v)	neponset_ncr_frob(0, v)
+#define neponset_ncr_clear(v)	neponset_ncr_frob(v, 0)
+
+#endif

linux-7.2.3/arch/arm/mach-sa1100/include/mach/reset.h

@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_ARCH_RESET_H
+#define __ASM_ARCH_RESET_H
+
+#include "hardware.h"
+
+#define RESET_STATUS_HARDWARE	(1 << 0)	/* Hardware Reset */
+#define RESET_STATUS_WATCHDOG	(1 << 1)	/* Watchdog Reset */
+#define RESET_STATUS_LOWPOWER	(1 << 2)	/* Exit from Low Power/Sleep */
+#define RESET_STATUS_GPIO	(1 << 3)	/* GPIO Reset */
+#define RESET_STATUS_ALL	(0xf)
+
+static inline void clear_reset_status(unsigned int mask)
+{
+	RCSR = mask;
+}
+
+#endif /* __ASM_ARCH_RESET_H */

linux-7.2.3/arch/arm/mach-sa1100/include/mach/uncompress.h

@@ -0,0 +1,52 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * arch/arm/mach-sa1100/include/mach/uncompress.h
+ *
+ * (C) 1999 Nicolas Pitre <nico@fluxnic.net>
+ *
+ * Reorganised to be machine independent.
+ */
+
+#include "hardware.h"
+
+#define IOMEM(x)	(x)
+
+/*
+ * The following code assumes the serial port has already been
+ * initialized by the bootloader.  We search for the first enabled
+ * port in the most probable order.  If you didn't setup a port in
+ * your bootloader then nothing will appear (which might be desired).
+ */
+
+#define UART(x)		(*(volatile unsigned long *)(serial_port + (x)))
+
+static inline void putc(int c)
+{
+	unsigned long serial_port;
+
+	do {
+		serial_port = _Ser3UTCR0;
+		if (UART(UTCR3) & UTCR3_TXE) break;
+		serial_port = _Ser1UTCR0;
+		if (UART(UTCR3) & UTCR3_TXE) break;
+		serial_port = _Ser2UTCR0;
+		if (UART(UTCR3) & UTCR3_TXE) break;
+		return;
+	} while (0);
+
+	/* wait for space in the UART's transmitter */
+	while (!(UART(UTSR1) & UTSR1_TNF))
+		barrier();
+
+	/* send the character out. */
+	UART(UTDR) = c;
+}
+
+static inline void flush(void)
+{
+}
+
+/*
+ * Nothing to do for these
+ */
+#define arch_decomp_setup()