Resguardo inicial

linux-7.2.3/arch/arm64/boot/dts/st/Makefile

@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0-only
+dtb-$(CONFIG_ARCH_STM32) += \
+	stm32mp215f-dk.dtb \
+	stm32mp235f-dk.dtb \
+	stm32mp257f-dk.dtb \
+	stm32mp257f-ev1.dtb

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp211.dtsi

@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a35";
+			reg = <0>;
+			device_type = "cpu";
+			enable-method = "psci";
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a35-pmu";
+		interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>;
+		interrupt-parent = <&intc>;
+	};
+
+	arm_wdt: watchdog {
+		compatible = "arm,smc-wdt";
+		arm,smc-id = <0xbc000000>;
+		status = "disabled";
+	};
+
+	ck_flexgen_08: clock-64000000 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <64000000>;
+	};
+
+	ck_flexgen_51: clock-200000000 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <200000000>;
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+
+		scmi: scmi {
+			compatible = "linaro,scmi-optee";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			linaro,optee-channel-id = <0>;
+
+			scmi_clk: protocol@14 {
+				reg = <0x14>;
+				#clock-cells = <1>;
+			};
+
+			scmi_reset: protocol@16 {
+				reg = <0x16>;
+				#reset-cells = <1>;
+			};
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,no-tick-in-suspend;
+	};
+
+	soc@0 {
+		compatible = "simple-bus";
+		ranges = <0x0 0x0 0x0 0x0 0x80000000>;
+		dma-ranges = <0x0 0x0 0x80000000 0x1 0x0>;
+		interrupt-parent = <&intc>;
+		#address-cells = <1>;
+		#size-cells = <2>;
+
+		rifsc: bus@42080000 {
+			compatible = "st,stm32mp21-rifsc", "simple-bus";
+			reg = <0x42080000 0x0 0x1000>;
+			ranges;
+			dma-ranges;
+			#address-cells = <1>;
+			#size-cells = <2>;
+			#access-controller-cells = <1>;
+
+			usart2: serial@400e0000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x400e0000 0x0 0x400>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&ck_flexgen_08>;
+				access-controllers = <&rifsc 32>;
+				status = "disabled";
+			};
+		};
+
+		bsec: efuse@44000000 {
+			compatible = "st,stm32mp25-bsec";
+			reg = <0x44000000 0x0 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			part_number_otp@24 {
+				reg = <0x24 0x4>;
+			};
+
+			package_otp@1e8 {
+				reg = <0x1e8 0x1>;
+				bits = <0 3>;
+			};
+		};
+
+		syscfg: syscon@44230000 {
+			compatible = "st,stm32mp21-syscfg", "syscon";
+			reg = <0x44230000 0x0 0x10000>;
+		};
+
+		intc: interrupt-controller@4ac10000 {
+			compatible = "arm,gic-400";
+			reg = <0x4ac10000 0x0 0x1000>,
+			      <0x4ac20000 0x0 0x20000>,
+			      <0x4ac40000 0x0 0x20000>,
+			      <0x4ac60000 0x0 0x20000>;
+			      #interrupt-cells = <3>;
+			      interrupt-controller;
+		};
+	};
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp213.dtsi

@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp211.dtsi"
+
+/ {
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp215.dtsi

@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp213.dtsi"
+
+/ {
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp215f-dk.dts

@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Amelie Delaunay <amelie.delaunay@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp215.dtsi"
+#include "stm32mp21xf.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP215F-DK Discovery Board";
+	compatible = "st,stm32mp215f-dk", "st,stm32mp215";
+
+	aliases {
+		serial0 = &usart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x0 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		fw@80000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x80000000 0x0 0x4000000>;
+			no-map;
+		};
+	};
+};
+
+&arm_wdt {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&bsec {
+	bootph-all;
+};
+
+&usart2 {
+	status = "okay";
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp21xf.dtsi

@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp233.dtsi

@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp231.dtsi"
+
+/ {
+	cpus {
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a35";
+			reg = <1>;
+			device_type = "cpu";
+			enable-method = "psci";
+			power-domains = <&cpu1_pd>;
+			power-domain-names = "psci";
+		};
+	};
+
+	arm-pmu {
+		interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+
+	psci {
+		cpu1_pd: power-domain-cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&cluster_pd>;
+		};
+	};
+
+	timer {
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
+
+&optee {
+	interrupts = <GIC_PPI 15 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+};
+
+&rifsc {
+	ethernet2: ethernet@482d0000 {
+		compatible = "st,stm32mp25-dwmac", "snps,dwmac-5.20";
+		reg = <0x482d0000 0x4000>;
+		reg-names = "stmmaceth";
+		interrupts-extended = <&intc GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "macirq";
+		clock-names = "stmmaceth",
+			      "mac-clk-tx",
+			      "mac-clk-rx",
+			      "ptp_ref",
+			      "ethstp",
+			      "eth-ck";
+		clocks = <&rcc CK_ETH2_MAC>,
+			 <&rcc CK_ETH2_TX>,
+			 <&rcc CK_ETH2_RX>,
+			 <&rcc CK_KER_ETH2PTP>,
+			 <&rcc CK_ETH2_STP>,
+			 <&rcc CK_KER_ETH2>;
+		snps,axi-config = <&stmmac_axi_config_2>;
+		snps,mixed-burst;
+		snps,mtl-rx-config = <&mtl_rx_setup_2>;
+		snps,mtl-tx-config = <&mtl_tx_setup_2>;
+		snps,pbl = <2>;
+		snps,tso;
+		st,syscon = <&syscfg 0x3400>;
+		access-controllers = <&rifsc 61>;
+		status = "disabled";
+
+		mtl_rx_setup_2: rx-queues-config {
+			snps,rx-queues-to-use = <2>;
+			queue0 {};
+			queue1 {};
+		};
+
+		mtl_tx_setup_2: tx-queues-config {
+			snps,tx-queues-to-use = <4>;
+			queue0 {};
+			queue1 {};
+			queue2 {};
+			queue3 {};
+		};
+
+		stmmac_axi_config_2: stmmac-axi-config {
+			snps,blen = <0 0 0 0 16 8 4>;
+			snps,rd_osr_lmt = <0x7>;
+			snps,wr_osr_lmt = <0x7>;
+		};
+	};
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp235.dtsi

@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp233.dtsi"
+
+&ltdc {
+	compatible = "st,stm32mp255-ltdc";
+	clocks = <&clk_flexgen_27_fixed>, <&rcc CK_BUS_LTDC>, <&syscfg>, <&lvds>;
+	clock-names = "lcd", "bus", "ref", "lvds";
+};
+
+&rifsc {
+	lvds: lvds@48060000 {
+		compatible = "st,stm32mp255-lvds", "st,stm32mp25-lvds";
+		reg = <0x48060000 0x2000>;
+		#clock-cells = <0>;
+		clocks = <&rcc CK_BUS_LVDS>, <&rcc CK_KER_LVDSPHY>;
+		clock-names = "pclk", "ref";
+		resets = <&rcc LVDS_R>;
+		access-controllers = <&rifsc 84>;
+		power-domains = <&cluster_pd>;
+		status = "disabled";
+	};
+
+	vdec: vdec@480d0000 {
+		compatible = "st,stm32mp25-vdec";
+		reg = <0x480d0000 0x3c8>;
+		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rcc CK_BUS_VDEC>;
+		access-controllers = <&rifsc 89>;
+	};
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp235f-dk.dts

@@ -0,0 +1,283 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Amelie Delaunay <amelie.delaunay@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "stm32mp235.dtsi"
+#include "stm32mp23xf.dtsi"
+#include "stm32mp25-pinctrl.dtsi"
+#include "stm32mp25xxak-pinctrl.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP235F-DK Discovery Board";
+	compatible = "st,stm32mp235f-dk", "st,stm32mp235";
+
+	aliases {
+		ethernet0 = &ethernet1;
+		serial0 = &usart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-user-1 {
+			label = "User-1";
+			linux,code = <BTN_1>;
+			gpios = <&gpioc 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		button-user-2 {
+			label = "User-2";
+			linux,code = <BTN_2>;
+			gpios = <&gpioc 11 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led_blue: led-blue {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpioh 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led-green {
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioh 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-orange {
+			color = <LED_COLOR_ID_ORANGE>;
+			gpios = <&gpioh 6 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x0 0x80000000>;
+	};
+
+	options {
+		u-boot {
+			compatible = "u-boot,config";
+			boot-led = <&led_blue>;
+		};
+	};
+
+	panel_lvds: display {
+		compatible = "edt,etml0700z9ndha", "panel-lvds";
+		enable-gpios = <&gpioi 4 GPIO_ACTIVE_HIGH>;
+		backlight = <&panel_lvds_backlight>;
+		power-supply = <&scmi_v3v3>;
+		width-mm = <156>;
+		height-mm = <92>;
+		data-mapping = "vesa-24";
+		status = "okay";
+
+		panel-timing {
+			clock-frequency = <54000000>;
+			hactive = <1024>;
+			vactive = <600>;
+			hfront-porch = <150>;
+			hback-porch = <150>;
+			hsync-len = <21>;
+			vfront-porch = <24>;
+			vback-porch = <24>;
+			vsync-len = <21>;
+		};
+
+		port {
+			lvds_panel_in: endpoint {
+				remote-endpoint = <&lvds_out0>;
+			};
+		};
+	};
+
+	panel_lvds_backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpioi 4 GPIO_ACTIVE_HIGH>;
+		default-on;
+		status = "okay";
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		fw@80000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x80000000 0x0 0x4000000>;
+			no-map;
+		};
+	};
+};
+
+&arm_wdt {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&ethernet1 {
+	pinctrl-0 = <&eth1_rgmii_pins_b>;
+	pinctrl-1 = <&eth1_rgmii_sleep_pins_b>;
+	pinctrl-names = "default", "sleep";
+	phy-handle = <&phy1_eth1>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy1_eth1: ethernet-phy@1 {
+			compatible = "ethernet-phy-id001c.c916";
+			reg = <1>;
+			reset-gpios = <&gpioa 2 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <80000>;
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_b>;
+	pinctrl-1 = <&i2c2_sleep_pins_b>;
+	i2c-scl-rising-time-ns = <108>;
+	i2c-scl-falling-time-ns = <12>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	ili2511: ili2511@41 {
+		compatible = "ilitek,ili251x";
+		reg = <0x41>;
+		interrupt-parent = <&gpioi>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpioi 0 GPIO_ACTIVE_LOW>;
+		status = "okay";
+	};
+};
+
+&i2c8 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c8_pins_a>;
+	pinctrl-1 = <&i2c8_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <100000>;
+	status = "disabled";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&ltdc {
+	status = "okay";
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&lvds_in>;
+		};
+	};
+};
+
+&lvds {
+	status = "okay";
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			lvds_in: endpoint {
+				remote-endpoint = <&ltdc_ep0_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			lvds_out0: endpoint {
+				remote-endpoint = <&lvds_panel_in>;
+			};
+		};
+	};
+};
+
+&scmi_regu {
+	scmi_vddio1: regulator@0 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+	scmi_vddcore: regulator@11 {
+		reg = <VOLTD_SCMI_STPMIC2_BUCK2>;
+		regulator-name = "vddcore";
+	};
+	scmi_v1v8: regulator@14 {
+		reg = <VOLTD_SCMI_STPMIC2_BUCK5>;
+		regulator-name = "v1v8";
+	};
+	scmi_v3v3: regulator@16 {
+		reg = <VOLTD_SCMI_STPMIC2_BUCK7>;
+		regulator-name = "v3v3";
+	};
+	scmi_vdd_emmc: regulator@18 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO2>;
+		regulator-name = "vdd_emmc";
+	};
+	scmi_vdd3v3_usb: regulator@20 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO4>;
+		regulator-name = "vdd3v3_usb";
+	};
+	scmi_v5v_hdmi: regulator@21 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO5>;
+		regulator-name = "v5v_hdmi";
+	};
+	scmi_v5v_vconn: regulator@22 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO6>;
+		regulator-name = "v5v_vconn";
+	};
+	scmi_vdd_sdcard: regulator@23 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO7>;
+		regulator-name = "vdd_sdcard";
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpiod 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&scmi_vdd_sdcard>;
+	vqmmc-supply = <&scmi_vddio1>;
+	status = "okay";
+};
+
+&usart2 {
+	pinctrl-names = "default", "idle", "sleep";
+	pinctrl-0 = <&usart2_pins_a>;
+	pinctrl-1 = <&usart2_idle_pins_a>;
+	pinctrl-2 = <&usart2_sleep_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp23xf.dtsi

@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp25-pinctrl.dtsi

@@ -0,0 +1,595 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+&pinctrl {
+	/omit-if-no-ref/
+	eth1_mdio_pins_a: eth1-mdio-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 0, AF10)>; /* ETH_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 2, AF10)>; /* ETH_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	eth1_mdio_sleep_pins_a: eth1-mdio-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 0, ANALOG)>, /* ETH_MDC */
+				 <STM32_PINMUX('F', 2, ANALOG)>; /* ETH_MDIO */
+		};
+	};
+
+	/omit-if-no-ref/
+	eth1_rgmii_pins_a: eth1-rgmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 15, AF10)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('C', 1, AF10)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('H', 10, AF10)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('H', 11, AF10)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('A', 13, AF10)>; /* ETH_RGMII_TX_CTL */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+			st,io-sync = "data on both edges";
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('H', 9, AF10)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('C', 0, AF12)>; /* ETH_RGMII_GTX_CLK */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('F', 1, AF10)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 2, AF10)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 12, AF10)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('H', 13, AF10)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 11, AF10)>; /* ETH_RGMII_RX_CTL */
+			bias-disable;
+			st,io-sync = "data on both edges";
+		};
+		pins4 {
+			pinmux = <STM32_PINMUX('A', 14, AF10)>; /* ETH_RGMII_RX_CLK */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	eth1_rgmii_sleep_pins_a: eth1-rgmii-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 15, ANALOG)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('H', 10, ANALOG)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('H', 11, ANALOG)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('A', 13, ANALOG)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('H', 9, ANALOG)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('C', 0, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('F', 1, ANALOG)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 12, ANALOG)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('H', 13, ANALOG)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 11, ANALOG)>, /* ETH_RGMII_RX_CTL */
+				 <STM32_PINMUX('A', 14, ANALOG)>; /* ETH_RGMII_RX_CLK */
+		};
+	};
+
+	/omit-if-no-ref/
+	eth1_rgmii_pins_b: eth1-rgmii-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 15, AF10)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('C', 1, AF10)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('H', 10, AF10)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('H', 11, AF10)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('A', 13, AF10)>; /* ETH_RGMII_TX_CTL */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('H', 9, AF10)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('C', 0, AF12)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('A', 9, AF10)>, /* ETH_MDC */
+				 <STM32_PINMUX('A', 10, AF10)>; /* ETH_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('F', 1, AF10)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 2, AF10)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 12, AF10)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('H', 13, AF10)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 11, AF10)>; /* ETH_RGMII_RX_CTL */
+			bias-disable;
+		};
+		pins4 {
+			pinmux = <STM32_PINMUX('A', 14, AF10)>; /* ETH_RGMII_RX_CLK */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	eth1_rgmii_sleep_pins_b: eth1-rgmii-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 15, ANALOG)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('H', 10, ANALOG)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('H', 11, ANALOG)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('A', 13, ANALOG)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('H', 9, ANALOG)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('C', 0, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('A', 9, ANALOG)>, /* ETH_MDC */
+				 <STM32_PINMUX('A', 10, ANALOG)>, /* ETH_MDIO */
+				 <STM32_PINMUX('F', 1, ANALOG)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 12, ANALOG)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('H', 13, ANALOG)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 11, ANALOG)>, /* ETH_RGMII_RX_CTL */
+				 <STM32_PINMUX('A', 14, AF10)>; /* ETH_RGMII_RX_CLK */
+		};
+	};
+
+	/omit-if-no-ref/
+	eth2_rgmii_pins_a: eth2-rgmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 7, AF10)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('C', 8, AF10)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 9, AF10)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('C', 10, AF10)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('C', 4, AF10)>; /* ETH_RGMII_TX_CTL */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+			st,io-sync = "data on both edges";
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 8, AF10)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('F', 7, AF10)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('C', 6, AF10)>; /* ETH_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('C', 5, AF10)>; /* ETH_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins4 {
+			pinmux = <STM32_PINMUX('G', 0, AF10)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 12, AF10)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('F', 9, AF10)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('C', 11, AF10)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('C', 3, AF10)>; /* ETH_RGMII_RX_CTL */
+			bias-disable;
+			st,io-sync = "data on both edges";
+		};
+		pins5 {
+			pinmux = <STM32_PINMUX('F', 6, AF10)>; /* ETH_RGMII_RX_CLK */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	eth2_rgmii_sleep_pins_a: eth2-rgmii-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 7, ANALOG)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('C', 8, ANALOG)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 9, ANALOG)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('C', 10, ANALOG)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('F', 8, ANALOG)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('F', 7, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('C', 6, ANALOG)>, /* ETH_MDC */
+				 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_MDIO */
+				 <STM32_PINMUX('G', 0, ANALOG)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 12, ANALOG)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('F', 9, ANALOG)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('C', 11, ANALOG)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('C', 3, ANALOG)>, /* ETH_RGMII_RX_CTL */
+				 <STM32_PINMUX('F', 6, ANALOG)>; /* ETH_RGMII_RX_CLK */
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c2_pins_a: i2c2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 5, AF9)>, /* I2C2_SCL */
+				 <STM32_PINMUX('B', 4, AF9)>; /* I2C2_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c2_sleep_pins_a: i2c2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 5, ANALOG)>, /* I2C2_SCL */
+				 <STM32_PINMUX('B', 4, ANALOG)>; /* I2C2_SDA */
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c2_pins_b: i2c2-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 2, AF9)>, /* I2C2_SCL */
+				 <STM32_PINMUX('F', 0, AF9)>; /* I2C2_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c2_sleep_pins_b: i2c2-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* I2C2_SCL */
+				 <STM32_PINMUX('F', 0, ANALOG)>; /* I2C2_SDA */
+		};
+	};
+
+	/omit-if-no-ref/
+	ospi_port1_clk_pins_a: ospi-port1-clk-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 0, AF10)>; /* OSPI1_CLK */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+	};
+
+	/omit-if-no-ref/
+	ospi_port1_clk_sleep_pins_a: ospi-port1-clk-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 0, ANALOG)>; /* OSPI1_CLK */
+		};
+	};
+
+	/omit-if-no-ref/
+	ospi_port1_cs0_pins_a: ospi-port1-cs0-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 3, AF10)>; /* OSPI_NCS0 */
+			bias-pull-up;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	ospi_port1_cs0_sleep_pins_a: ospi-port1-cs0-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 3, ANALOG)>; /* OSPI_NCS0 */
+		};
+	};
+
+	/omit-if-no-ref/
+	ospi_port1_io03_pins_a: ospi-port1-io03-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 4, AF10)>, /* OSPI_IO0 */
+				 <STM32_PINMUX('D', 5, AF10)>, /* OSPI_IO1 */
+				 <STM32_PINMUX('D', 6, AF10)>, /* OSPI_IO2 */
+				 <STM32_PINMUX('D', 7, AF10)>; /* OSPI_IO3 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	ospi_port1_io03_sleep_pins_a: ospi-port1-io03-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 4, ANALOG)>, /* OSPI_IO0 */
+				 <STM32_PINMUX('D', 5, ANALOG)>, /* OSPI_IO1 */
+				 <STM32_PINMUX('D', 6, ANALOG)>, /* OSPI_IO2 */
+				 <STM32_PINMUX('D', 7, ANALOG)>; /* OSPI_IO3 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pcie_pins_a: pcie-0 {
+		pins {
+			pinmux = <STM32_PINMUX('J', 0, AF4)>;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	pcie_init_pins_a: pcie-init-0 {
+		pins {
+			pinmux = <STM32_PINMUX('J', 0, GPIO)>;
+			output-low;
+		};
+	};
+
+	/omit-if-no-ref/
+	pcie_sleep_pins_a: pcie-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('J', 0, ANALOG)>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm3_pins_a: pwm3-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 15, AF7)>; /* TIM3_CH2 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm3_sleep_pins_a: pwm3-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 15, ANALOG)>; /* TIM3_CH2 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm8_pins_a: pwm8-0 {
+		pins {
+			pinmux = <STM32_PINMUX('J', 5, AF8)>, /* TIM8_CH1 */
+				 <STM32_PINMUX('J', 4, AF8)>; /* TIM8_CH4 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm8_sleep_pins_a: pwm8-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('J', 5, ANALOG)>, /* TIM8_CH1 */
+				 <STM32_PINMUX('J', 4, ANALOG)>; /* TIM8_CH4 */
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm12_pins_a: pwm12-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 11, AF9)>; /* TIM12_CH2 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	pwm12_sleep_pins_a: pwm12-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 11, ANALOG)>; /* TIM12_CH2 */
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_b4_pins_a: sdmmc1-b4-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 4, AF10)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('E', 5, AF10)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('E', 0, AF10)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('E', 1, AF10)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('E', 2, AF10)>; /* SDMMC1_CMD */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 3, AF10)>; /* SDMMC1_CK */
+			slew-rate = <3>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 4, AF10)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('E', 5, AF10)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('E', 0, AF10)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('E', 1, AF10)>; /* SDMMC1_D3 */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 3, AF10)>; /* SDMMC1_CK */
+			slew-rate = <3>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('E', 2, AF10)>; /* SDMMC1_CMD */
+			slew-rate = <2>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 4, ANALOG)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('E', 5, ANALOG)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('E', 0, ANALOG)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('E', 1, ANALOG)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('E', 2, ANALOG)>; /* SDMMC1_CMD */
+		};
+	};
+
+	/omit-if-no-ref/
+	spi3_pins_a: spi3-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 7, AF1)>, /* SPI3_SCK */
+				 <STM32_PINMUX('B', 8, AF1)>; /* SPI3_MOSI */
+			drive-push-pull;
+			bias-disable;
+			slew-rate = <1>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 10, AF1)>; /* SPI3_MISO */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	spi3_sleep_pins_a: spi3-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 7, ANALOG)>, /* SPI3_SCK */
+				 <STM32_PINMUX('B', 8, ANALOG)>, /* SPI3_MOSI */
+				 <STM32_PINMUX('B', 10, ANALOG)>; /* SPI3_MISO */
+		};
+	};
+
+	/omit-if-no-ref/
+	tim10_counter_pins_a: tim10-counter-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 9, AF9)>; /* TIM10_CH1 */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	tim10_counter_sleep_pins_a: tim10-counter-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 9, ANALOG)>; /* TIM10_CH1 */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart2_pins_a: usart2-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 4, AF6)>; /* USART2_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 8, AF8)>; /* USART2_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart2_idle_pins_a: usart2-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 4, ANALOG)>; /* USART2_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 8, AF8)>; /* USART2_RX */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart2_sleep_pins_a: usart2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('A', 8, ANALOG)>; /* USART2_RX */
+		};
+	};
+
+	/omit-if-no-ref/
+	usart6_pins_a: usart6-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 13, AF3)>, /* USART6_TX */
+				 <STM32_PINMUX('G', 5, AF3)>;  /* USART6_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 14, AF3)>, /* USART6_RX */
+				 <STM32_PINMUX('F', 15, AF3)>; /* USART6_CTS_NSS */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart6_idle_pins_a: usart6-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 13, ANALOG)>, /* USART6_TX */
+				 <STM32_PINMUX('F', 15, ANALOG)>; /* USART6_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 5, AF3)>; /* USART6_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('F', 14, AF3)>; /* USART6_RX */
+			bias-pull-up;
+		};
+	};
+
+	/omit-if-no-ref/
+	usart6_sleep_pins_a: usart6-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 13, ANALOG)>, /* USART6_TX */
+				 <STM32_PINMUX('G', 5, ANALOG)>,  /* USART6_RTS */
+				 <STM32_PINMUX('F', 15, ANALOG)>, /* USART6_CTS_NSS */
+				 <STM32_PINMUX('F', 14, ANALOG)>; /* USART6_RX */
+		};
+	};
+};
+
+&pinctrl_z {
+	/omit-if-no-ref/
+	i2c8_pins_a: i2c8-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 4, AF8)>, /* I2C8_SCL */
+				 <STM32_PINMUX('Z', 3, AF8)>; /* I2C8_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	/omit-if-no-ref/
+	i2c8_sleep_pins_a: i2c8-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 4, ANALOG)>, /* I2C8_SCL */
+				 <STM32_PINMUX('Z', 3, ANALOG)>; /* I2C8_SDA */
+		};
+	};
+
+	/omit-if-no-ref/
+	spi8_pins_a: spi8-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('Z', 2, AF3)>, /* SPI8_SCK */
+				 <STM32_PINMUX('Z', 0, AF3)>; /* SPI8_MOSI */
+			drive-push-pull;
+			bias-disable;
+			slew-rate = <1>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('Z', 1, AF3)>; /* SPI8_MISO */
+			bias-disable;
+		};
+	};
+
+	/omit-if-no-ref/
+	spi8_sleep_pins_a: spi8-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('Z', 2, ANALOG)>, /* SPI8_SCK */
+				 <STM32_PINMUX('Z', 0, ANALOG)>, /* SPI8_MOSI */
+				 <STM32_PINMUX('Z', 1, ANALOG)>; /* SPI8_MISO */
+		};
+	};
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp253.dtsi

@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp251.dtsi"
+
+/ {
+	cpus {
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a35";
+			device_type = "cpu";
+			reg = <1>;
+			enable-method = "psci";
+			power-domains = <&CPU_PD1>;
+			power-domain-names = "psci";
+		};
+	};
+
+	arm-pmu {
+		interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+
+	psci {
+		CPU_PD1: power-domain-cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+		};
+	};
+
+	timer {
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
+
+&optee {
+	interrupts = <GIC_PPI 15 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+};
+
+&rifsc {
+	ethernet2: ethernet@482d0000 {
+		compatible = "st,stm32mp25-dwmac", "snps,dwmac-5.20";
+		reg = <0x482d0000 0x4000>;
+		reg-names = "stmmaceth";
+		interrupts-extended = <&intc GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "macirq";
+		clock-names = "stmmaceth",
+			      "mac-clk-tx",
+			      "mac-clk-rx",
+			      "ptp_ref",
+			      "ethstp",
+			      "eth-ck";
+		clocks = <&rcc CK_ETH2_MAC>,
+			 <&rcc CK_ETH2_TX>,
+			 <&rcc CK_ETH2_RX>,
+			 <&rcc CK_KER_ETH2PTP>,
+			 <&rcc CK_ETH2_STP>,
+			 <&rcc CK_KER_ETH2>;
+		snps,axi-config = <&stmmac_axi_config_2>;
+		snps,mixed-burst;
+		snps,mtl-rx-config = <&mtl_rx_setup_2>;
+		snps,mtl-tx-config = <&mtl_tx_setup_2>;
+		snps,pbl = <2>;
+		snps,tso;
+		st,syscon = <&syscfg 0x3400>;
+		access-controllers = <&rifsc 61>;
+		status = "disabled";
+
+		mtl_rx_setup_2: rx-queues-config {
+			snps,rx-queues-to-use = <2>;
+			queue0 {};
+			queue1 {};
+		};
+
+		mtl_tx_setup_2: tx-queues-config {
+			snps,tx-queues-to-use = <4>;
+			queue0 {};
+			queue1 {};
+			queue2 {};
+			queue3 {};
+		};
+
+		stmmac_axi_config_2: stmmac-axi-config {
+			snps,blen = <0 0 0 0 16 8 4>;
+			snps,rd_osr_lmt = <0x7>;
+			snps,wr_osr_lmt = <0x7>;
+		};
+	};
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp255.dtsi

@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp253.dtsi"
+
+&ltdc {
+	compatible = "st,stm32mp255-ltdc";
+	clocks = <&clk_flexgen_27_fixed>, <&rcc CK_BUS_LTDC>, <&syscfg>, <&lvds>;
+	clock-names = "lcd", "bus", "ref", "lvds";
+};
+
+&rifsc {
+	lvds: lvds@48060000 {
+		compatible = "st,stm32mp255-lvds", "st,stm32mp25-lvds";
+		reg = <0x48060000 0x2000>;
+		#clock-cells = <0>;
+		clocks = <&rcc CK_BUS_LVDS>, <&rcc CK_KER_LVDSPHY>;
+		clock-names = "pclk", "ref";
+		resets = <&rcc LVDS_R>;
+		access-controllers = <&rifsc 84>;
+		power-domains = <&CLUSTER_PD>;
+		status = "disabled";
+	};
+
+	vdec: vdec@480d0000 {
+		compatible = "st,stm32mp25-vdec";
+		reg = <0x480d0000 0x3c8>;
+		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rcc CK_BUS_VDEC>;
+		access-controllers = <&rifsc 89>;
+
+	};
+
+	venc: venc@480e0000 {
+		compatible = "st,stm32mp25-venc";
+		reg = <0x480e0000 0x800>;
+		interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rcc CK_BUS_VENC>;
+		access-controllers = <&rifsc 90>;
+	};
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp257.dtsi

@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include "stm32mp255.dtsi"
+
+/ {
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp257f-dk.dts

@@ -0,0 +1,290 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2025 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "stm32mp257.dtsi"
+#include "stm32mp25xf.dtsi"
+#include "stm32mp25-pinctrl.dtsi"
+#include "stm32mp25xxak-pinctrl.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP257F-DK Discovery Board";
+	compatible = "st,stm32mp257f-dk", "st,stm32mp257";
+
+	aliases {
+		ethernet0 = &ethernet1;
+		serial0 = &usart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-user-1 {
+			label = "User-1";
+			linux,code = <BTN_1>;
+			gpios = <&gpioc 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		button-user-2 {
+			label = "User-2";
+			linux,code = <BTN_2>;
+			gpios = <&gpioc 11 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led_blue: led-blue {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpioh 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led-green {
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioh 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-orange {
+			color = <LED_COLOR_ID_ORANGE>;
+			gpios = <&gpioh 6 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	lpddr_channel: sdram-channel-0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "jedec,lpddr4-channel";
+		io-width = <32>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x1 0x0>;
+	};
+
+	options {
+		u-boot {
+			compatible = "u-boot,config";
+			boot-led = <&led_blue>;
+		};
+	};
+
+	panel_lvds: display {
+		compatible = "edt,etml0700z9ndha", "panel-lvds";
+		enable-gpios = <&gpioi 4 GPIO_ACTIVE_HIGH>;
+		backlight = <&panel_lvds_backlight>;
+		power-supply = <&scmi_v3v3>;
+		width-mm = <156>;
+		height-mm = <92>;
+		data-mapping = "vesa-24";
+		status = "okay";
+
+		panel-timing {
+			clock-frequency = <54000000>;
+			hactive = <1024>;
+			vactive = <600>;
+			hfront-porch = <150>;
+			hback-porch = <150>;
+			hsync-len = <21>;
+			vfront-porch = <24>;
+			vback-porch = <24>;
+			vsync-len = <21>;
+		};
+
+		port {
+			lvds_panel_in: endpoint {
+				remote-endpoint = <&lvds_out0>;
+			};
+		};
+	};
+
+	panel_lvds_backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpioi 4 GPIO_ACTIVE_HIGH>;
+		default-on;
+		status = "okay";
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		fw@80000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x80000000 0x0 0x4000000>;
+			no-map;
+		};
+	};
+};
+
+&arm_wdt {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&ethernet1 {
+	pinctrl-0 = <&eth1_rgmii_pins_b>;
+	pinctrl-1 = <&eth1_rgmii_sleep_pins_b>;
+	pinctrl-names = "default", "sleep";
+	phy-handle = <&phy1_eth1>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy1_eth1: ethernet-phy@1 {
+			compatible = "ethernet-phy-id001c.c916";
+			reg = <1>;
+			reset-gpios = <&gpioa 2 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <80000>;
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_b>;
+	pinctrl-1 = <&i2c2_sleep_pins_b>;
+	i2c-scl-rising-time-ns = <108>;
+	i2c-scl-falling-time-ns = <12>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	ili2511: ili2511@41 {
+		compatible = "ilitek,ili251x";
+		reg = <0x41>;
+		interrupt-parent = <&gpioi>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpioi 0 GPIO_ACTIVE_LOW>;
+		status = "okay";
+	};
+};
+
+&i2c8 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c8_pins_a>;
+	pinctrl-1 = <&i2c8_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <100000>;
+	status = "disabled";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&ltdc {
+	status = "okay";
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&lvds_in>;
+		};
+	};
+};
+
+&lvds {
+	status = "okay";
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			lvds_in: endpoint {
+				remote-endpoint = <&ltdc_ep0_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			lvds_out0: endpoint {
+				remote-endpoint = <&lvds_panel_in>;
+			};
+		};
+	};
+};
+
+&scmi_regu {
+	scmi_vddio1: regulator@0 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+	scmi_vddcore: regulator@11 {
+		reg = <VOLTD_SCMI_STPMIC2_BUCK2>;
+		regulator-name = "vddcore";
+	};
+	scmi_v1v8: regulator@14 {
+		reg = <VOLTD_SCMI_STPMIC2_BUCK5>;
+		regulator-name = "v1v8";
+	};
+	scmi_v3v3: regulator@16 {
+		reg = <VOLTD_SCMI_STPMIC2_BUCK7>;
+		regulator-name = "v3v3";
+	};
+	scmi_vdd_emmc: regulator@18 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO2>;
+		regulator-name = "vdd_emmc";
+	};
+	scmi_vdd3v3_usb: regulator@20 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO4>;
+		regulator-name = "vdd3v3_usb";
+	};
+	scmi_v5v_hdmi: regulator@21 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO5>;
+		regulator-name = "v5v_hdmi";
+	};
+	scmi_v5v_vconn: regulator@22 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO6>;
+		regulator-name = "v5v_vconn";
+	};
+	scmi_vdd_sdcard: regulator@23 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO7>;
+		regulator-name = "vdd_sdcard";
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpiod 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&scmi_vdd_sdcard>;
+	vqmmc-supply = <&scmi_vddio1>;
+	status = "okay";
+};
+
+&usart2 {
+	pinctrl-names = "default", "idle", "sleep";
+	pinctrl-0 = <&usart2_pins_a>;
+	pinctrl-1 = <&usart2_idle_pins_a>;
+	pinctrl-2 = <&usart2_sleep_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp257f-ev1.dts

@@ -0,0 +1,536 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/st,stm32mp25-regulator.h>
+#include "stm32mp257.dtsi"
+#include "stm32mp25xf.dtsi"
+#include "stm32mp25-pinctrl.dtsi"
+#include "stm32mp25xxai-pinctrl.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP257F-EV1 Evaluation Board";
+	compatible = "st,stm32mp257f-ev1", "st,stm32mp257";
+
+	aliases {
+		ethernet0 = &ethernet2;
+		ethernet1 = &ethernet1;
+		serial0 = &usart2;
+		serial1 = &usart6;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		clk_ext_camera: clk-ext-camera {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+		};
+
+		pad_clk: pad-clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <100000000>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led_blue: led-blue {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpioj 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led-green {
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpiod 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-orange {
+			color = <LED_COLOR_ID_ORANGE>;
+			gpios = <&gpioj 6 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	ddr_channel: sdram-channel-0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "jedec,ddr4-channel";
+		io-width = <32>;
+	};
+
+	imx335_2v9: regulator-2v9 {
+		compatible = "regulator-fixed";
+		regulator-name = "imx335-avdd";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-always-on;
+	};
+
+	imx335_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "imx335-ovdd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	imx335_1v2: regulator-1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "imx335-dvdd";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x1 0x0>;
+	};
+
+	options {
+		u-boot {
+			compatible = "u-boot,config";
+			boot-led = <&led_blue>;
+		};
+	};
+
+	panel_lvds: display {
+		compatible = "edt,etml0700z9ndha", "panel-lvds";
+		enable-gpios = <&gpiog 15 GPIO_ACTIVE_HIGH>;
+		backlight = <&panel_lvds_backlight>;
+		power-supply = <&scmi_v3v3>;
+		width-mm = <156>;
+		height-mm = <92>;
+		data-mapping = "vesa-24";
+		status = "okay";
+
+		panel-timing {
+			clock-frequency = <54000000>;
+			hactive = <1024>;
+			vactive = <600>;
+			hfront-porch = <150>;
+			hback-porch = <150>;
+			hsync-len = <21>;
+			vfront-porch = <24>;
+			vback-porch = <24>;
+			vsync-len = <21>;
+		};
+
+		port {
+			lvds_panel_in: endpoint {
+				remote-endpoint = <&lvds_out0>;
+			};
+		};
+	};
+
+	panel_lvds_backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
+		default-on;
+		status = "okay";
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		fw@80000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x80000000 0x0 0x4000000>;
+			no-map;
+		};
+
+		mm_ospi1: mm-ospi@60000000 {
+			reg = <0x0 0x60000000 0x0 0x10000000>;
+			no-map;
+		};
+	};
+};
+
+&arm_wdt {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&combophy {
+	clocks = <&rcc CK_BUS_USB3PCIEPHY>, <&rcc CK_KER_USB3PCIEPHY>, <&pad_clk>;
+	clock-names = "apb", "ker", "pad";
+	status = "okay";
+};
+
+&csi {
+	vdd-supply = <&scmi_vddcore>;
+	vdda18-supply = <&scmi_v1v8>;
+	status = "okay";
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		port@0 {
+			reg = <0>;
+			csi_sink: endpoint {
+				remote-endpoint = <&imx335_ep>;
+				data-lanes = <1 2>;
+				bus-type = <4>;
+			};
+		};
+		port@1 {
+			reg = <1>;
+			csi_source: endpoint {
+				remote-endpoint = <&dcmipp_0>;
+			};
+		};
+	};
+};
+
+&dcmipp {
+	status = "okay";
+	port {
+		dcmipp_0: endpoint {
+			remote-endpoint = <&csi_source>;
+			bus-type = <4>;
+		};
+	};
+};
+
+&ethernet1 {
+	pinctrl-0 = <&eth1_rgmii_pins_a &eth1_mdio_pins_a>;
+	pinctrl-1 = <&eth1_rgmii_sleep_pins_a &eth1_mdio_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-handle = <&phy1_eth1>;
+	phy-mode = "rgmii-id";
+	st,ext-phyclk;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy1_eth1: ethernet-phy@4 {
+			compatible = "ethernet-phy-id001c.c916";
+			reg = <4>;
+			reset-gpios = <&gpioj 9 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <80000>;
+		};
+	};
+};
+
+&ethernet2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&eth2_rgmii_pins_a>;
+	pinctrl-1 = <&eth2_rgmii_sleep_pins_a>;
+	max-speed = <1000>;
+	phy-handle = <&phy0_eth2>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0_eth2: ethernet-phy@1 {
+			compatible = "ethernet-phy-id001c.c916";
+			reg = <1>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+			reset-gpios = <&gpiog 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_a>;
+	pinctrl-1 = <&i2c2_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <13>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	imx335: camera@1a {
+		compatible = "sony,imx335";
+		reg = <0x1a>;
+		clocks = <&clk_ext_camera>;
+		avdd-supply = <&imx335_2v9>;
+		ovdd-supply = <&imx335_1v8>;
+		dvdd-supply = <&imx335_1v2>;
+		reset-gpios = <&gpioi 7 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
+
+		port {
+			imx335_ep: endpoint {
+				remote-endpoint = <&csi_sink>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				link-frequencies = /bits/ 64 <594000000>;
+			};
+		};
+	};
+
+	ili2511: ili2511@41 {
+		compatible = "ilitek,ili251x";
+		reg = <0x41>;
+		interrupt-parent = <&gpioi>;
+		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpiog 14 GPIO_ACTIVE_LOW>;
+		status = "okay";
+	};
+};
+
+&i2c8 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c8_pins_a>;
+	pinctrl-1 = <&i2c8_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <57>;
+	i2c-scl-falling-time-ns = <7>;
+	clock-frequency = <400000>;
+	status = "disabled";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&ommanager {
+	memory-region = <&mm_ospi1>;
+	memory-region-names = "ospi1";
+	pinctrl-0 = <&ospi_port1_clk_pins_a
+		     &ospi_port1_io03_pins_a
+		     &ospi_port1_cs0_pins_a>;
+	pinctrl-1 = <&ospi_port1_clk_sleep_pins_a
+		     &ospi_port1_io03_sleep_pins_a
+		     &ospi_port1_cs0_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	status = "okay";
+
+	spi@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		memory-region = <&mm_ospi1>;
+		status = "okay";
+
+		flash0: flash@0 {
+			compatible = "jedec,spi-nor";
+			reg = <0>;
+			spi-rx-bus-width = <4>;
+			spi-tx-bus-width = <4>;
+			spi-max-frequency = <50000000>;
+		};
+	};
+};
+
+/* use LPTIMER with tick broadcast for suspend mode */
+&lptimer3 {
+	status = "okay";
+	timer {
+		status = "okay";
+	};
+};
+
+&ltdc {
+	status = "okay";
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&lvds_in>;
+		};
+	};
+};
+
+&lvds {
+	status = "okay";
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			lvds_in: endpoint {
+				remote-endpoint = <&ltdc_ep0_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			lvds_out0: endpoint {
+				remote-endpoint = <&lvds_panel_in>;
+			};
+		};
+	};
+};
+
+&pcie_ep {
+	pinctrl-names = "default", "init";
+	pinctrl-0 = <&pcie_pins_a>;
+	pinctrl-1 = <&pcie_init_pins_a>;
+	reset-gpios = <&gpioj 8 GPIO_ACTIVE_LOW>;
+	status = "disabled";
+};
+
+&pcie_rc {
+	pinctrl-names = "default", "init", "sleep";
+	pinctrl-0 = <&pcie_pins_a>;
+	pinctrl-1 = <&pcie_init_pins_a>;
+	pinctrl-2 = <&pcie_sleep_pins_a>;
+	status = "okay";
+
+	pcie@0,0 {
+		 reset-gpios = <&gpioj 8 GPIO_ACTIVE_LOW>;
+		 wake-gpios = <&gpioh 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&scmi_regu {
+	scmi_vddio1: regulator@0 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+	scmi_vddcore: regulator@11  {
+		reg = <VOLTD_SCMI_STPMIC2_BUCK2>;
+		regulator-name = "vddcore";
+	};
+	scmi_v1v8: regulator@14  {
+		reg = <VOLTD_SCMI_STPMIC2_BUCK5>;
+		regulator-name = "v1v8";
+	};
+	scmi_v3v3: regulator@16 {
+		reg = <VOLTD_SCMI_STPMIC2_BUCK7>;
+		regulator-name = "v3v3";
+	};
+	scmi_vdd_emmc: regulator@18 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO2>;
+		regulator-name = "vdd_emmc";
+	};
+	scmi_vdd3v3_usb: regulator@20 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO4>;
+		regulator-name = "vdd3v3_usb";
+	};
+	scmi_vdd_sdcard: regulator@23 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO7>;
+		regulator-name = "vdd_sdcard";
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpiod 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&scmi_vdd_sdcard>;
+	vqmmc-supply = <&scmi_vddio1>;
+	status = "okay";
+};
+
+&spi3 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi3_pins_a>;
+	pinctrl-1 = <&spi3_sleep_pins_a>;
+	status = "disabled";
+};
+
+&spi8 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi8_pins_a>;
+	pinctrl-1 = <&spi8_sleep_pins_a>;
+	status = "disabled";
+};
+
+&timers3 {
+	status = "disabled";
+	counter {
+		status = "okay";
+	};
+	pwm {
+		pinctrl-0 = <&pwm3_pins_a>;
+		pinctrl-1 = <&pwm3_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@2 {
+		status = "okay";
+	};
+};
+
+&timers8 {
+	status = "disabled";
+	counter {
+		status = "okay";
+	};
+	pwm {
+		pinctrl-0 = <&pwm8_pins_a>;
+		pinctrl-1 = <&pwm8_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@7 {
+		status = "okay";
+	};
+};
+
+&timers10 {
+	status = "disabled";
+	counter {
+		pinctrl-0 = <&tim10_counter_pins_a>;
+		pinctrl-1 = <&tim10_counter_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+};
+
+&timers12 {
+	status = "disabled";
+	counter {
+		status = "okay";
+	};
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-1 = <&pwm12_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@11 {
+		status = "okay";
+	};
+};
+
+&usart2 {
+	pinctrl-names = "default", "idle", "sleep";
+	pinctrl-0 = <&usart2_pins_a>;
+	pinctrl-1 = <&usart2_idle_pins_a>;
+	pinctrl-2 = <&usart2_sleep_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usart6 {
+	pinctrl-names = "default", "idle", "sleep";
+	pinctrl-0 = <&usart6_pins_a>;
+	pinctrl-1 = <&usart6_idle_pins_a>;
+	pinctrl-2 = <&usart6_sleep_pins_a>;
+	uart-has-rtscts;
+	status = "disabled";
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp25xf.dtsi

@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp25xxai-pinctrl.dtsi

@@ -0,0 +1,83 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+&pinctrl {
+	st,package = <STM32MP_PKG_AI>;
+
+	gpioa: gpio@44240000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@44250000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@44260000 {
+		status = "okay";
+		ngpios = <14>;
+		gpio-ranges = <&pinctrl 0 32 14>;
+	};
+
+	gpiod: gpio@44270000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@44280000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@44290000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@442a0000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@442b0000 {
+		status = "okay";
+		ngpios = <12>;
+		gpio-ranges = <&pinctrl 2 114 12>;
+	};
+
+	gpioi: gpio@442c0000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 128 16>;
+	};
+
+	gpioj: gpio@442d0000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 144 16>;
+	};
+
+	gpiok: gpio@442e0000 {
+		status = "okay";
+		ngpios = <8>;
+		gpio-ranges = <&pinctrl 0 160 8>;
+	};
+};
+
+&pinctrl_z {
+	gpioz: gpio@46200000 {
+		status = "okay";
+		ngpios = <10>;
+		gpio-ranges = <&pinctrl_z 0 400 10>;
+	};
+};

linux-7.2.3/arch/arm64/boot/dts/st/stm32mp25xxak-pinctrl.dtsi

@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2023 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+&pinctrl {
+	st,package = <STM32MP_PKG_AK>;
+
+	gpioa: gpio@44240000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@44250000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@44260000 {
+		status = "okay";
+		ngpios = <14>;
+		gpio-ranges = <&pinctrl 0 32 14>;
+	};
+
+	gpiod: gpio@44270000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@44280000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@44290000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@442a0000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@442b0000 {
+		status = "okay";
+		ngpios = <12>;
+		gpio-ranges = <&pinctrl 2 114 12>;
+	};
+
+	gpioi: gpio@442c0000 {
+		status = "okay";
+		ngpios = <12>;
+		gpio-ranges = <&pinctrl 0 128 12>;
+	};
+};
+
+&pinctrl_z {
+	gpioz: gpio@46200000 {
+		status = "okay";
+		ngpios = <10>;
+		gpio-ranges = <&pinctrl_z 0 400 10>;
+	};
+};