Resguardo inicial

linux-7.2.3/arch/powerpc/platforms/83xx/Kconfig

@@ -0,0 +1,92 @@
+# SPDX-License-Identifier: GPL-2.0
+menuconfig PPC_83xx
+	bool "83xx-based boards"
+	depends on PPC_BOOK3S_32
+	select PPC_UDBG_16550
+	select HAVE_PCI
+	select FSL_PCI if PCI
+	select FSL_SOC
+	select IPIC
+
+if PPC_83xx
+
+config MPC830x_RDB
+	bool "Freescale MPC830x RDB and derivatives"
+	select DEFAULT_UIMAGE
+	select PPC_MPC831x
+	select FSL_GTM
+	help
+	  This option enables support for the MPC8308 RDB and MPC8308 P1M boards.
+
+config MPC831x_RDB
+	bool "Freescale MPC831x RDB"
+	select DEFAULT_UIMAGE
+	select PPC_MPC831x
+	help
+	  This option enables support for the MPC8313 RDB and MPC8315 RDB boards.
+
+config MPC832x_RDB
+	bool "Freescale MPC832x RDB"
+	select DEFAULT_UIMAGE
+	select PPC_MPC832x
+	help
+	  This option enables support for the MPC8323 RDB board.
+
+config MPC834x_ITX
+	bool "Freescale MPC834x ITX"
+	select DEFAULT_UIMAGE
+	select PPC_MPC834x
+	help
+	  This option enables support for the MPC 834x ITX evaluation board.
+
+	  Be aware that PCI initialization is the bootloader's
+	  responsibility.
+
+config MPC836x_RDK
+	bool "Freescale/Logic MPC836x RDK"
+	select DEFAULT_UIMAGE
+	select FSL_GTM
+	select FSL_LBC
+	help
+	  This option enables support for the MPC836x RDK Processor Board,
+	  also known as ZOOM PowerQUICC Kit.
+
+config MPC837x_RDB
+	bool "Freescale MPC837x RDB/WLAN"
+	select DEFAULT_UIMAGE
+	select PPC_MPC837x
+	help
+	  This option enables support for the MPC837x RDB and WLAN Boards.
+
+config ASP834x
+	bool "Analogue & Micro ASP 834x"
+	select PPC_MPC834x
+	help
+	  This enables support for the Analogue & Micro ASP 83xx
+	  board.
+
+config KMETER1
+	bool "Keymile KMETER1"
+	select DEFAULT_UIMAGE
+	select QUICC_ENGINE
+	help
+	  This enables support for the Keymile KMETER1 board.
+
+
+endif
+
+# used for usb & gpio
+config PPC_MPC831x
+	bool
+
+# used for math-emu
+config PPC_MPC832x
+	bool
+
+# used for usb & gpio
+config PPC_MPC834x
+	bool
+
+# used for usb & gpio
+config PPC_MPC837x
+	bool

linux-7.2.3/arch/powerpc/platforms/83xx/Makefile

@@ -0,0 +1,18 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the PowerPC 83xx linux kernel.
+#
+obj-y				:= misc.o
+obj-$(CONFIG_SUSPEND)		+= suspend.o suspend-asm.o
+obj-$(CONFIG_MCU_MPC8349EMITX)	+= mcu_mpc8349emitx.o
+obj-$(CONFIG_MPC830x_RDB)	+= mpc830x_rdb.o
+obj-$(CONFIG_MPC831x_RDB)	+= mpc831x_rdb.o
+obj-$(CONFIG_MPC832x_RDB)	+= mpc832x_rdb.o
+obj-$(CONFIG_MPC834x_ITX)	+= mpc834x_itx.o
+obj-$(CONFIG_MPC836x_RDK)	+= mpc836x_rdk.o
+obj-$(CONFIG_MPC837x_RDB)	+= mpc837x_rdb.o
+obj-$(CONFIG_ASP834x)		+= asp834x.o
+obj-$(CONFIG_KMETER1)		+= km83xx.o
+obj-$(CONFIG_PPC_MPC831x)	+= usb_831x.o
+obj-$(CONFIG_PPC_MPC834x)	+= usb_834x.o
+obj-$(CONFIG_PPC_MPC837x)	+= usb_837x.o

linux-7.2.3/arch/powerpc/platforms/83xx/asp834x.c

@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * arch/powerpc/platforms/83xx/asp834x.c
+ *
+ * Analogue & Micro ASP8347 board specific routines
+ * clone of mpc834x_itx
+ *
+ * Copyright 2008 Codehermit
+ *
+ * Maintainer: Bryan O'Donoghue <bodonoghue@codhermit.ie>
+ */
+
+#include <linux/pci.h>
+#include <linux/of_platform.h>
+
+#include <asm/time.h>
+#include <asm/ipic.h>
+#include <asm/udbg.h>
+
+#include "mpc83xx.h"
+
+/* ************************************************************************
+ *
+ * Setup the architecture
+ *
+ */
+static void __init asp834x_setup_arch(void)
+{
+	mpc83xx_setup_arch();
+	mpc834x_usb_cfg();
+}
+
+machine_device_initcall(asp834x, mpc83xx_declare_of_platform_devices);
+
+define_machine(asp834x) {
+	.name			= "ASP8347E",
+	.compatible		= "analogue-and-micro,asp8347e",
+	.setup_arch		= asp834x_setup_arch,
+	.discover_phbs		= mpc83xx_setup_pci,
+	.init_IRQ		= mpc83xx_ipic_init_IRQ,
+	.get_irq		= ipic_get_irq,
+	.restart		= mpc83xx_restart,
+	.time_init		= mpc83xx_time_init,
+	.progress		= udbg_progress,
+};

linux-7.2.3/arch/powerpc/platforms/83xx/km83xx.c

@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2008-2011 DENX Software Engineering GmbH
+ * Author: Heiko Schocher <hs@denx.de>
+ *
+ * Description:
+ * Keymile 83xx platform specific routines.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/reboot.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/major.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/seq_file.h>
+#include <linux/root_dev.h>
+#include <linux/initrd.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+
+#include <linux/atomic.h>
+#include <linux/time.h>
+#include <linux/io.h>
+#include <asm/machdep.h>
+#include <asm/ipic.h>
+#include <asm/irq.h>
+#include <asm/udbg.h>
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+#include <soc/fsl/qe/qe.h>
+
+#include "mpc83xx.h"
+
+#define SVR_REV(svr)    (((svr) >>  0) & 0xFFFF) /* Revision field */
+
+static void __init quirk_mpc8360e_qe_enet10(void)
+{
+	/*
+	 * handle mpc8360E Erratum QE_ENET10:
+	 * RGMII AC values do not meet the specification
+	 */
+	uint svid = mfspr(SPRN_SVR);
+	struct	device_node *np_par;
+	struct	resource res;
+	void	__iomem *base;
+	int	ret;
+
+	np_par = of_find_node_by_name(NULL, "par_io");
+	if (np_par == NULL) {
+		pr_warn("%s couldn't find par_io node\n", __func__);
+		return;
+	}
+	/* Map Parallel I/O ports registers */
+	ret = of_address_to_resource(np_par, 0, &res);
+	if (ret) {
+		pr_warn("%s couldn't map par_io registers\n", __func__);
+		goto out;
+	}
+
+	base = ioremap(res.start, resource_size(&res));
+	if (!base)
+		goto out;
+
+	/*
+	 * set output delay adjustments to default values according
+	 * table 5 in Errata Rev. 5, 9/2011:
+	 *
+	 * write 0b01 to UCC1 bits 18:19
+	 * write 0b01 to UCC2 option 1 bits 4:5
+	 * write 0b01 to UCC2 option 2 bits 16:17
+	 */
+	clrsetbits_be32((base + 0xa8), 0x0c00f000, 0x04005000);
+
+	/*
+	 * set output delay adjustments to default values according
+	 * table 3-13 in Reference Manual Rev.3 05/2010:
+	 *
+	 * write 0b01 to UCC2 option 2 bits 16:17
+	 * write 0b0101 to UCC1 bits 20:23
+	 * write 0b0101 to UCC2 option 1 bits 24:27
+	 */
+	clrsetbits_be32((base + 0xac), 0x0000cff0, 0x00004550);
+
+	if (SVR_REV(svid) == 0x0021) {
+		/*
+		 * UCC2 option 1: write 0b1010 to bits 24:27
+		 * at address IMMRBAR+0x14AC
+		 */
+		clrsetbits_be32((base + 0xac), 0x000000f0, 0x000000a0);
+	} else if (SVR_REV(svid) == 0x0020) {
+		/*
+		 * UCC1: write 0b11 to bits 18:19
+		 * at address IMMRBAR+0x14A8
+		 */
+		setbits32((base + 0xa8), 0x00003000);
+
+		/*
+		 * UCC2 option 1: write 0b11 to bits 4:5
+		 * at address IMMRBAR+0x14A8
+		 */
+		setbits32((base + 0xa8), 0x0c000000);
+
+		/*
+		 * UCC2 option 2: write 0b11 to bits 16:17
+		 * at address IMMRBAR+0x14AC
+		 */
+		setbits32((base + 0xac), 0x0000c000);
+	}
+	iounmap(base);
+out:
+	of_node_put(np_par);
+}
+
+/* ************************************************************************
+ *
+ * Setup the architecture
+ *
+ */
+static void __init mpc83xx_km_setup_arch(void)
+{
+#ifdef CONFIG_QUICC_ENGINE
+	struct device_node *np;
+#endif
+
+	mpc83xx_setup_arch();
+
+#ifdef CONFIG_QUICC_ENGINE
+	np = of_find_node_by_name(NULL, "par_io");
+	if (np != NULL) {
+		par_io_init(np);
+		of_node_put(np);
+
+		for_each_node_by_name(np, "spi")
+			par_io_of_config(np);
+
+		for_each_node_by_name(np, "ucc")
+			par_io_of_config(np);
+
+		/* Only apply this quirk when par_io is available */
+		np = of_find_compatible_node(NULL, "network", "ucc_geth");
+		if (np != NULL) {
+			quirk_mpc8360e_qe_enet10();
+			of_node_put(np);
+		}
+	}
+#endif	/* CONFIG_QUICC_ENGINE */
+}
+
+machine_device_initcall(mpc83xx_km, mpc83xx_declare_of_platform_devices);
+
+/* list of the supported boards */
+static char *board[] __initdata = {
+	"keymile,KMETER1",
+	"keymile,kmpbec8321",
+	NULL
+};
+
+/*
+ * Called very early, MMU is off, device-tree isn't unflattened
+ */
+static int __init mpc83xx_km_probe(void)
+{
+	int i = 0;
+
+	while (board[i]) {
+		if (of_machine_is_compatible(board[i]))
+			break;
+		i++;
+	}
+	return (board[i] != NULL);
+}
+
+define_machine(mpc83xx_km) {
+	.name		= "mpc83xx-km-platform",
+	.probe		= mpc83xx_km_probe,
+	.setup_arch	= mpc83xx_km_setup_arch,
+	.discover_phbs	= mpc83xx_setup_pci,
+	.init_IRQ	= mpc83xx_ipic_init_IRQ,
+	.get_irq	= ipic_get_irq,
+	.restart	= mpc83xx_restart,
+	.time_init	= mpc83xx_time_init,
+	.progress	= udbg_progress,
+};

linux-7.2.3/arch/powerpc/platforms/83xx/mcu_mpc8349emitx.c

@@ -0,0 +1,229 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Power Management and GPIO expander driver for MPC8349E-mITX-compatible MCU
+ *
+ * Copyright (c) 2008  MontaVista Software, Inc.
+ *
+ * Author: Anton Vorontsov <avorontsov@ru.mvista.com>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/mutex.h>
+#include <linux/i2c.h>
+#include <linux/gpio/driver.h>
+#include <linux/slab.h>
+#include <linux/sysfs.h>
+#include <linux/kthread.h>
+#include <linux/property.h>
+#include <linux/reboot.h>
+#include <asm/machdep.h>
+
+/*
+ * I don't have specifications for the MCU firmware, I found this register
+ * and bits positions by the trial&error method.
+ */
+#define MCU_REG_CTRL	0x20
+#define MCU_CTRL_POFF	0x40
+#define MCU_CTRL_BTN	0x80
+
+#define MCU_NUM_GPIO	2
+
+struct mcu {
+	struct mutex lock;
+	struct i2c_client *client;
+	struct gpio_chip gc;
+	u8 reg_ctrl;
+};
+
+static struct mcu *glob_mcu;
+
+struct task_struct *shutdown_thread;
+static int shutdown_thread_fn(void *data)
+{
+	int ret;
+	struct mcu *mcu = glob_mcu;
+
+	while (!kthread_should_stop()) {
+		ret = i2c_smbus_read_byte_data(mcu->client, MCU_REG_CTRL);
+		if (ret < 0)
+			pr_err("MCU status reg read failed.\n");
+		mcu->reg_ctrl = ret;
+
+
+		if (mcu->reg_ctrl & MCU_CTRL_BTN) {
+			i2c_smbus_write_byte_data(mcu->client, MCU_REG_CTRL,
+						  mcu->reg_ctrl & ~MCU_CTRL_BTN);
+
+			ctrl_alt_del();
+		}
+
+		set_current_state(TASK_INTERRUPTIBLE);
+		schedule_timeout(HZ);
+	}
+
+	return 0;
+}
+
+static ssize_t show_status(struct device *d,
+			   struct device_attribute *attr, char *buf)
+{
+	int ret;
+	struct mcu *mcu = glob_mcu;
+
+	ret = i2c_smbus_read_byte_data(mcu->client, MCU_REG_CTRL);
+	if (ret < 0)
+		return -ENODEV;
+	mcu->reg_ctrl = ret;
+
+	return sysfs_emit(buf, "%02x\n", ret);
+}
+static DEVICE_ATTR(status, 0444, show_status, NULL);
+
+static void mcu_power_off(void)
+{
+	struct mcu *mcu = glob_mcu;
+
+	pr_info("Sending power-off request to the MCU...\n");
+	mutex_lock(&mcu->lock);
+	i2c_smbus_write_byte_data(mcu->client, MCU_REG_CTRL,
+				  mcu->reg_ctrl | MCU_CTRL_POFF);
+	mutex_unlock(&mcu->lock);
+}
+
+static int mcu_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct mcu *mcu = gpiochip_get_data(gc);
+	u8 bit = 1 << (4 + gpio);
+	int ret;
+
+	mutex_lock(&mcu->lock);
+	if (val)
+		mcu->reg_ctrl &= ~bit;
+	else
+		mcu->reg_ctrl |= bit;
+
+	ret = i2c_smbus_write_byte_data(mcu->client, MCU_REG_CTRL,
+					mcu->reg_ctrl);
+	mutex_unlock(&mcu->lock);
+
+	return ret;
+}
+
+static int mcu_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	return mcu_gpio_set(gc, gpio, val);
+}
+
+static int mcu_gpiochip_add(struct mcu *mcu)
+{
+	struct device *dev = &mcu->client->dev;
+	struct gpio_chip *gc = &mcu->gc;
+
+	gc->owner = THIS_MODULE;
+	gc->label = kasprintf(GFP_KERNEL, "%pfw", dev_fwnode(dev));
+	if (!gc->label)
+		return -ENOMEM;
+	gc->can_sleep = 1;
+	gc->ngpio = MCU_NUM_GPIO;
+	gc->base = -1;
+	gc->set = mcu_gpio_set;
+	gc->direction_output = mcu_gpio_dir_out;
+	gc->parent = dev;
+
+	return gpiochip_add_data(gc, mcu);
+}
+
+static void mcu_gpiochip_remove(struct mcu *mcu)
+{
+	kfree(mcu->gc.label);
+	gpiochip_remove(&mcu->gc);
+}
+
+static int mcu_probe(struct i2c_client *client)
+{
+	struct mcu *mcu;
+	int ret;
+
+	mcu = kzalloc_obj(*mcu);
+	if (!mcu)
+		return -ENOMEM;
+
+	mutex_init(&mcu->lock);
+	mcu->client = client;
+	i2c_set_clientdata(client, mcu);
+
+	ret = i2c_smbus_read_byte_data(mcu->client, MCU_REG_CTRL);
+	if (ret < 0)
+		goto err;
+	mcu->reg_ctrl = ret;
+
+	ret = mcu_gpiochip_add(mcu);
+	if (ret)
+		goto err;
+
+	/* XXX: this is potentially racy, but there is no lock for pm_power_off */
+	if (!pm_power_off) {
+		glob_mcu = mcu;
+		pm_power_off = mcu_power_off;
+		dev_info(&client->dev, "will provide power-off service\n");
+	}
+
+	if (device_create_file(&client->dev, &dev_attr_status))
+		dev_err(&client->dev,
+			"couldn't create device file for status\n");
+
+	shutdown_thread = kthread_run(shutdown_thread_fn, NULL,
+				      "mcu-i2c-shdn");
+
+	return 0;
+err:
+	kfree(mcu);
+	return ret;
+}
+
+static void mcu_remove(struct i2c_client *client)
+{
+	struct mcu *mcu = i2c_get_clientdata(client);
+
+	kthread_stop(shutdown_thread);
+
+	device_remove_file(&client->dev, &dev_attr_status);
+
+	if (glob_mcu == mcu) {
+		pm_power_off = NULL;
+		glob_mcu = NULL;
+	}
+
+	mcu_gpiochip_remove(mcu);
+	kfree(mcu);
+}
+
+static const struct i2c_device_id mcu_ids[] = {
+	{ "mcu-mpc8349emitx", },
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, mcu_ids);
+
+static const struct of_device_id mcu_of_match_table[] = {
+	{ .compatible = "fsl,mcu-mpc8349emitx", },
+	{ },
+};
+
+static struct i2c_driver mcu_driver = {
+	.driver = {
+		.name = "mcu-mpc8349emitx",
+		.of_match_table = mcu_of_match_table,
+	},
+	.probe = mcu_probe,
+	.remove	= mcu_remove,
+	.id_table = mcu_ids,
+};
+
+module_i2c_driver(mcu_driver);
+
+MODULE_DESCRIPTION("Power Management and GPIO expander driver for "
+		   "MPC8349E-mITX-compatible MCU");
+MODULE_AUTHOR("Anton Vorontsov <avorontsov@ru.mvista.com>");
+MODULE_LICENSE("GPL");

linux-7.2.3/arch/powerpc/platforms/83xx/misc.c

@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * misc setup functions for MPC83xx
+ *
+ * Maintainer: Kumar Gala <galak@kernel.crashing.org>
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+
+#include <asm/debug.h>
+#include <asm/io.h>
+#include <asm/hw_irq.h>
+#include <asm/ipic.h>
+#include <asm/fixmap.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+
+#include <mm/mmu_decl.h>
+
+#include "mpc83xx.h"
+
+static __be32 __iomem *restart_reg_base;
+
+static int __init mpc83xx_restart_init(void)
+{
+	/* map reset restart_reg_baseister space */
+	restart_reg_base = ioremap(get_immrbase() + 0x900, 0xff);
+
+	return 0;
+}
+
+arch_initcall(mpc83xx_restart_init);
+
+void __noreturn mpc83xx_restart(char *cmd)
+{
+#define RST_OFFSET	0x00000900
+#define RST_PROT_REG	0x00000018
+#define RST_CTRL_REG	0x0000001c
+
+	local_irq_disable();
+
+	if (restart_reg_base) {
+		/* enable software reset "RSTE" */
+		out_be32(restart_reg_base + (RST_PROT_REG >> 2), 0x52535445);
+
+		/* set software hard reset */
+		out_be32(restart_reg_base + (RST_CTRL_REG >> 2), 0x2);
+	} else {
+		printk (KERN_EMERG "Error: Restart registers not mapped, spinning!\n");
+	}
+
+	for (;;) ;
+}
+
+long __init mpc83xx_time_init(void)
+{
+#define SPCR_OFFSET	0x00000110
+#define SPCR_TBEN	0x00400000
+	__be32 __iomem *spcr = ioremap(get_immrbase() + SPCR_OFFSET, 4);
+	__be32 tmp;
+
+	tmp = in_be32(spcr);
+	out_be32(spcr, tmp | SPCR_TBEN);
+
+	iounmap(spcr);
+
+	return 0;
+}
+
+void __init mpc83xx_ipic_init_IRQ(void)
+{
+	struct device_node *np;
+
+	/* looking for fsl,pq2pro-pic which is asl compatible with fsl,ipic */
+	np = of_find_compatible_node(NULL, NULL, "fsl,ipic");
+	if (!np)
+		np = of_find_node_by_type(NULL, "ipic");
+	if (!np)
+		return;
+
+	ipic_init(np, 0);
+
+	of_node_put(np);
+
+	/* Initialize the default interrupt mapping priorities,
+	 * in case the boot rom changed something on us.
+	 */
+	ipic_set_default_priority();
+}
+
+static const struct of_device_id of_bus_ids[] __initconst = {
+	{ .type = "soc", },
+	{ .compatible = "soc", },
+	{ .compatible = "simple-bus" },
+	{ .compatible = "gianfar" },
+	{ .compatible = "gpio-leds", },
+	{ .type = "qe", },
+	{ .compatible = "fsl,qe", },
+	{},
+};
+
+int __init mpc83xx_declare_of_platform_devices(void)
+{
+	of_platform_bus_probe(NULL, of_bus_ids, NULL);
+	return 0;
+}
+
+#ifdef CONFIG_PCI
+void __init mpc83xx_setup_pci(void)
+{
+	struct device_node *np;
+
+	for_each_compatible_node(np, "pci", "fsl,mpc8349-pci")
+		mpc83xx_add_bridge(np);
+	for_each_compatible_node(np, "pci", "fsl,mpc8314-pcie")
+		mpc83xx_add_bridge(np);
+}
+#endif
+
+void __init mpc83xx_setup_arch(void)
+{
+	phys_addr_t immrbase = get_immrbase();
+	int immrsize = IS_ALIGNED(immrbase, SZ_2M) ? SZ_2M : SZ_1M;
+	unsigned long va = fix_to_virt(FIX_IMMR_BASE);
+
+	if (ppc_md.progress)
+		ppc_md.progress("mpc83xx_setup_arch()", 0);
+
+	setbat(-1, va, immrbase, immrsize, PAGE_KERNEL_NCG);
+	update_bats();
+}
+
+int machine_check_83xx(struct pt_regs *regs)
+{
+	u32 mask = 1 << (31 - IPIC_MCP_WDT);
+
+	if (!(regs->msr & SRR1_MCE_MCP) || !(ipic_get_mcp_status() & mask))
+		return machine_check_generic(regs);
+	ipic_clear_mcp_status(mask);
+
+	if (debugger_fault_handler(regs))
+		return 1;
+
+	die("Watchdog NMI Reset", regs, 0);
+
+	return 1;
+}

linux-7.2.3/arch/powerpc/platforms/83xx/mpc830x_rdb.c

@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * arch/powerpc/platforms/83xx/mpc830x_rdb.c
+ *
+ * Description: MPC830x RDB board specific routines.
+ * This file is based on mpc831x_rdb.c
+ *
+ * Copyright (C) Freescale Semiconductor, Inc. 2009. All rights reserved.
+ * Copyright (C) 2010. Ilya Yanok, Emcraft Systems, yanok@emcraft.com
+ */
+
+#include <linux/pci.h>
+#include <linux/of_platform.h>
+#include <asm/time.h>
+#include <asm/ipic.h>
+#include <asm/udbg.h>
+#include <sysdev/fsl_pci.h>
+#include <sysdev/fsl_soc.h>
+#include "mpc83xx.h"
+
+/*
+ * Setup the architecture
+ */
+static void __init mpc830x_rdb_setup_arch(void)
+{
+	mpc83xx_setup_arch();
+	mpc831x_usb_cfg();
+}
+
+static const char *board[] __initdata = {
+	"MPC8308RDB",
+	"fsl,mpc8308rdb",
+	"denx,mpc8308_p1m",
+	NULL
+};
+
+machine_device_initcall(mpc830x_rdb, mpc83xx_declare_of_platform_devices);
+
+define_machine(mpc830x_rdb) {
+	.name			= "MPC830x RDB",
+	.compatibles		= board,
+	.setup_arch		= mpc830x_rdb_setup_arch,
+	.discover_phbs		= mpc83xx_setup_pci,
+	.init_IRQ		= mpc83xx_ipic_init_IRQ,
+	.get_irq		= ipic_get_irq,
+	.restart		= mpc83xx_restart,
+	.time_init		= mpc83xx_time_init,
+	.progress		= udbg_progress,
+};

linux-7.2.3/arch/powerpc/platforms/83xx/mpc831x_rdb.c

@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * arch/powerpc/platforms/83xx/mpc831x_rdb.c
+ *
+ * Description: MPC831x RDB board specific routines.
+ * This file is based on mpc834x_sys.c
+ * Author: Lo Wlison <r43300@freescale.com>
+ *
+ * Copyright (C) Freescale Semiconductor, Inc. 2006. All rights reserved.
+ */
+
+#include <linux/pci.h>
+#include <linux/of_platform.h>
+
+#include <asm/time.h>
+#include <asm/ipic.h>
+#include <asm/udbg.h>
+#include <sysdev/fsl_pci.h>
+
+#include "mpc83xx.h"
+
+/*
+ * Setup the architecture
+ */
+static void __init mpc831x_rdb_setup_arch(void)
+{
+	mpc83xx_setup_arch();
+	mpc831x_usb_cfg();
+}
+
+static const char *board[] __initdata = {
+	"MPC8313ERDB",
+	"fsl,mpc8315erdb",
+	NULL
+};
+
+machine_device_initcall(mpc831x_rdb, mpc83xx_declare_of_platform_devices);
+
+define_machine(mpc831x_rdb) {
+	.name			= "MPC831x RDB",
+	.compatibles		= board,
+	.setup_arch		= mpc831x_rdb_setup_arch,
+	.discover_phbs		= mpc83xx_setup_pci,
+	.init_IRQ		= mpc83xx_ipic_init_IRQ,
+	.get_irq		= ipic_get_irq,
+	.restart		= mpc83xx_restart,
+	.time_init		= mpc83xx_time_init,
+	.progress		= udbg_progress,
+};

linux-7.2.3/arch/powerpc/platforms/83xx/mpc832x_rdb.c

@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * arch/powerpc/platforms/83xx/mpc832x_rdb.c
+ *
+ * Copyright (C) Freescale Semiconductor, Inc. 2007. All rights reserved.
+ *
+ * Description:
+ * MPC832x RDB board specific routines.
+ * This file is based on mpc832x_mds.c and mpc8313_rdb.c
+ * Author: Michael Barkowski <michael.barkowski@freescale.com>
+ */
+
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/mmc_spi.h>
+#include <linux/mmc/host.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/fsl_devices.h>
+
+#include <asm/time.h>
+#include <asm/ipic.h>
+#include <asm/udbg.h>
+#include <soc/fsl/qe/qe.h>
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+
+#include "mpc83xx.h"
+
+#undef DEBUG
+#ifdef DEBUG
+#define DBG(fmt...) udbg_printf(fmt)
+#else
+#define DBG(fmt...)
+#endif
+
+#ifdef CONFIG_QUICC_ENGINE
+static int __init of_fsl_spi_probe(char *type, char *compatible, u32 sysclk,
+				   struct spi_board_info *board_infos,
+				   unsigned int num_board_infos,
+				   void (*cs_control)(struct spi_device *dev,
+						      bool on))
+{
+	struct device_node *np;
+	unsigned int i = 0;
+
+	for_each_compatible_node(np, type, compatible) {
+		int ret;
+		unsigned int j;
+		const void *prop;
+		struct resource res[2];
+		struct platform_device *pdev;
+		struct fsl_spi_platform_data pdata = {
+			.cs_control = cs_control,
+		};
+
+		memset(res, 0, sizeof(res));
+
+		pdata.sysclk = sysclk;
+
+		prop = of_get_property(np, "reg", NULL);
+		if (!prop)
+			goto err;
+		pdata.bus_num = *(u32 *)prop;
+
+		prop = of_get_property(np, "cell-index", NULL);
+		if (prop)
+			i = *(u32 *)prop;
+
+		prop = of_get_property(np, "mode", NULL);
+		if (prop && !strcmp(prop, "cpu-qe"))
+			pdata.flags = SPI_QE_CPU_MODE;
+
+		for (j = 0; j < num_board_infos; j++) {
+			if (board_infos[j].bus_num == pdata.bus_num)
+				pdata.max_chipselect++;
+		}
+
+		if (!pdata.max_chipselect)
+			continue;
+
+		ret = of_address_to_resource(np, 0, &res[0]);
+		if (ret)
+			goto err;
+
+		ret = of_irq_to_resource(np, 0, &res[1]);
+		if (ret <= 0)
+			goto err;
+
+		pdev = platform_device_alloc("mpc83xx_spi", i);
+		if (!pdev)
+			goto err;
+
+		ret = platform_device_add_data(pdev, &pdata, sizeof(pdata));
+		if (ret)
+			goto unreg;
+
+		ret = platform_device_add_resources(pdev, res,
+						    ARRAY_SIZE(res));
+		if (ret)
+			goto unreg;
+
+		ret = platform_device_add(pdev);
+		if (ret)
+			goto unreg;
+
+		goto next;
+unreg:
+		platform_device_put(pdev);
+err:
+		pr_err("%pOF: registration failed\n", np);
+next:
+		i++;
+	}
+
+	return i;
+}
+
+static int __init fsl_spi_init(struct spi_board_info *board_infos,
+			       unsigned int num_board_infos,
+			       void (*cs_control)(struct spi_device *spi,
+						  bool on))
+{
+	u32 sysclk = -1;
+	int ret;
+
+	/* SPI controller is either clocked from QE or SoC clock */
+	sysclk = get_brgfreq();
+	if (sysclk == -1) {
+		sysclk = fsl_get_sys_freq();
+		if (sysclk == -1)
+			return -ENODEV;
+	}
+
+	ret = of_fsl_spi_probe(NULL, "fsl,spi", sysclk, board_infos,
+			       num_board_infos, cs_control);
+	if (!ret)
+		of_fsl_spi_probe("spi", "fsl_spi", sysclk, board_infos,
+				 num_board_infos, cs_control);
+
+	return spi_register_board_info(board_infos, num_board_infos);
+}
+
+static void mpc83xx_spi_cs_control(struct spi_device *spi, bool on)
+{
+	pr_debug("%s %d %d\n", __func__, spi_get_chipselect(spi, 0), on);
+	par_io_data_set(3, 13, on);
+}
+
+static struct mmc_spi_platform_data mpc832x_mmc_pdata = {
+	.ocr_mask = MMC_VDD_33_34,
+};
+
+static struct spi_board_info mpc832x_spi_boardinfo = {
+	.bus_num = 0x4c0,
+	.chip_select = 0,
+	.max_speed_hz = 50000000,
+	.modalias = "mmc_spi",
+	.platform_data = &mpc832x_mmc_pdata,
+};
+
+static int __init mpc832x_spi_init(void)
+{
+	struct device_node *np;
+
+	par_io_config_pin(3,  0, 3, 0, 1, 0); /* SPI1 MOSI, I/O */
+	par_io_config_pin(3,  1, 3, 0, 1, 0); /* SPI1 MISO, I/O */
+	par_io_config_pin(3,  2, 3, 0, 1, 0); /* SPI1 CLK,  I/O */
+	par_io_config_pin(3,  3, 2, 0, 1, 0); /* SPI1 SEL,  I   */
+
+	par_io_config_pin(3, 13, 1, 0, 0, 0); /* !SD_CS,    O */
+	par_io_config_pin(3, 14, 2, 0, 0, 0); /* SD_INSERT, I */
+	par_io_config_pin(3, 15, 2, 0, 0, 0); /* SD_PROTECT,I */
+
+	/*
+	 * Don't bother with legacy stuff when device tree contains
+	 * mmc-spi-slot node.
+	 */
+	np = of_find_compatible_node(NULL, NULL, "mmc-spi-slot");
+	of_node_put(np);
+	if (np)
+		return 0;
+	return fsl_spi_init(&mpc832x_spi_boardinfo, 1, mpc83xx_spi_cs_control);
+}
+machine_device_initcall(mpc832x_rdb, mpc832x_spi_init);
+#endif /* CONFIG_QUICC_ENGINE */
+
+/* ************************************************************************
+ *
+ * Setup the architecture
+ *
+ */
+static void __init mpc832x_rdb_setup_arch(void)
+{
+#if defined(CONFIG_QUICC_ENGINE)
+	struct device_node *np;
+#endif
+
+	mpc83xx_setup_arch();
+
+#ifdef CONFIG_QUICC_ENGINE
+	if ((np = of_find_node_by_name(NULL, "par_io")) != NULL) {
+		par_io_init(np);
+		of_node_put(np);
+
+		for_each_node_by_name(np, "ucc")
+			par_io_of_config(np);
+	}
+#endif				/* CONFIG_QUICC_ENGINE */
+}
+
+machine_device_initcall(mpc832x_rdb, mpc83xx_declare_of_platform_devices);
+
+define_machine(mpc832x_rdb) {
+	.name		= "MPC832x RDB",
+	.compatible	= "MPC832xRDB",
+	.setup_arch	= mpc832x_rdb_setup_arch,
+	.discover_phbs  = mpc83xx_setup_pci,
+	.init_IRQ	= mpc83xx_ipic_init_IRQ,
+	.get_irq	= ipic_get_irq,
+	.restart	= mpc83xx_restart,
+	.time_init	= mpc83xx_time_init,
+	.progress	= udbg_progress,
+};

linux-7.2.3/arch/powerpc/platforms/83xx/mpc834x_itx.c

@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * arch/powerpc/platforms/83xx/mpc834x_itx.c
+ *
+ * MPC834x ITX board specific routines
+ *
+ * Maintainer: Kumar Gala <galak@kernel.crashing.org>
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/reboot.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/major.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/seq_file.h>
+#include <linux/root_dev.h>
+#include <linux/of_platform.h>
+
+#include <linux/atomic.h>
+#include <asm/time.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/ipic.h>
+#include <asm/irq.h>
+#include <asm/udbg.h>
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+
+#include "mpc83xx.h"
+
+static const struct of_device_id mpc834x_itx_ids[] __initconst = {
+	{ .compatible = "fsl,pq2pro-localbus", },
+	{},
+};
+
+static int __init mpc834x_itx_declare_of_platform_devices(void)
+{
+	mpc83xx_declare_of_platform_devices();
+	return of_platform_bus_probe(NULL, mpc834x_itx_ids, NULL);
+}
+machine_device_initcall(mpc834x_itx, mpc834x_itx_declare_of_platform_devices);
+
+/* ************************************************************************
+ *
+ * Setup the architecture
+ *
+ */
+static void __init mpc834x_itx_setup_arch(void)
+{
+	mpc83xx_setup_arch();
+
+	mpc834x_usb_cfg();
+}
+
+define_machine(mpc834x_itx) {
+	.name			= "MPC834x ITX",
+	.compatible		= "MPC834xMITX",
+	.setup_arch		= mpc834x_itx_setup_arch,
+	.discover_phbs  	= mpc83xx_setup_pci,
+	.init_IRQ		= mpc83xx_ipic_init_IRQ,
+	.get_irq		= ipic_get_irq,
+	.restart		= mpc83xx_restart,
+	.time_init		= mpc83xx_time_init,
+	.progress		= udbg_progress,
+};

linux-7.2.3/arch/powerpc/platforms/83xx/mpc836x_rdk.c

@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * MPC8360E-RDK board file.
+ *
+ * Copyright (c) 2006  Freescale Semiconductor, Inc.
+ * Copyright (c) 2007-2008  MontaVista Software, Inc.
+ *
+ * Author: Anton Vorontsov <avorontsov@ru.mvista.com>
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/of_platform.h>
+#include <linux/io.h>
+#include <asm/time.h>
+#include <asm/ipic.h>
+#include <asm/udbg.h>
+#include <soc/fsl/qe/qe.h>
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+
+#include "mpc83xx.h"
+
+machine_device_initcall(mpc836x_rdk, mpc83xx_declare_of_platform_devices);
+
+static void __init mpc836x_rdk_setup_arch(void)
+{
+	mpc83xx_setup_arch();
+}
+
+define_machine(mpc836x_rdk) {
+	.name		= "MPC836x RDK",
+	.compatible	= "fsl,mpc8360rdk",
+	.setup_arch	= mpc836x_rdk_setup_arch,
+	.discover_phbs  = mpc83xx_setup_pci,
+	.init_IRQ	= mpc83xx_ipic_init_IRQ,
+	.get_irq	= ipic_get_irq,
+	.restart	= mpc83xx_restart,
+	.time_init	= mpc83xx_time_init,
+	.progress	= udbg_progress,
+};

linux-7.2.3/arch/powerpc/platforms/83xx/mpc837x_rdb.c

@@ -0,0 +1,74 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * arch/powerpc/platforms/83xx/mpc837x_rdb.c
+ *
+ * Copyright (C) 2007 Freescale Semiconductor, Inc. All rights reserved.
+ *
+ * MPC837x RDB board specific routines
+ */
+
+#include <linux/pci.h>
+#include <linux/of_platform.h>
+
+#include <asm/time.h>
+#include <asm/ipic.h>
+#include <asm/udbg.h>
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+
+#include "mpc83xx.h"
+
+static void __init mpc837x_rdb_sd_cfg(void)
+{
+	void __iomem *im;
+
+	im = ioremap(get_immrbase(), 0x1000);
+	if (!im) {
+		WARN_ON(1);
+		return;
+	}
+
+	/*
+	 * On RDB boards (in contrast to MDS) USBB pins are used for SD only,
+	 * so we can safely mux them away from the USB block.
+	 */
+	clrsetbits_be32(im + MPC83XX_SICRL_OFFS, MPC837X_SICRL_USBB_MASK,
+						 MPC837X_SICRL_SD);
+	clrsetbits_be32(im + MPC83XX_SICRH_OFFS, MPC837X_SICRH_SPI_MASK,
+						 MPC837X_SICRH_SD);
+	iounmap(im);
+}
+
+/* ************************************************************************
+ *
+ * Setup the architecture
+ *
+ */
+static void __init mpc837x_rdb_setup_arch(void)
+{
+	mpc83xx_setup_arch();
+	mpc837x_usb_cfg();
+	mpc837x_rdb_sd_cfg();
+}
+
+machine_device_initcall(mpc837x_rdb, mpc83xx_declare_of_platform_devices);
+
+static const char * const board[] __initconst = {
+	"fsl,mpc8377rdb",
+	"fsl,mpc8378rdb",
+	"fsl,mpc8379rdb",
+	"fsl,mpc8377wlan",
+	NULL
+};
+
+define_machine(mpc837x_rdb) {
+	.name			= "MPC837x RDB/WLAN",
+	.compatibles		= board,
+	.setup_arch		= mpc837x_rdb_setup_arch,
+	.discover_phbs  	= mpc83xx_setup_pci,
+	.init_IRQ		= mpc83xx_ipic_init_IRQ,
+	.get_irq		= ipic_get_irq,
+	.restart		= mpc83xx_restart,
+	.time_init		= mpc83xx_time_init,
+	.progress		= udbg_progress,
+};

linux-7.2.3/arch/powerpc/platforms/83xx/mpc83xx.h

@@ -0,0 +1,83 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __MPC83XX_H__
+#define __MPC83XX_H__
+
+#include <linux/init.h>
+
+/* System Clock Control Register */
+#define MPC83XX_SCCR_OFFS          0xA08
+#define MPC83XX_SCCR_USB_MASK      0x00f00000
+#define MPC83XX_SCCR_USB_MPHCM_11  0x00c00000
+#define MPC83XX_SCCR_USB_MPHCM_01  0x00400000
+#define MPC83XX_SCCR_USB_MPHCM_10  0x00800000
+#define MPC83XX_SCCR_USB_DRCM_11   0x00300000
+#define MPC83XX_SCCR_USB_DRCM_01   0x00100000
+#define MPC83XX_SCCR_USB_DRCM_10   0x00200000
+#define MPC8315_SCCR_USB_MASK      0x00c00000
+#define MPC8315_SCCR_USB_DRCM_11   0x00c00000
+#define MPC8315_SCCR_USB_DRCM_01   0x00400000
+#define MPC837X_SCCR_USB_DRCM_11   0x00c00000
+
+/* system i/o configuration register low */
+#define MPC83XX_SICRL_OFFS         0x114
+#define MPC834X_SICRL_USB_MASK     0x60000000
+#define MPC834X_SICRL_USB0         0x20000000
+#define MPC834X_SICRL_USB1         0x40000000
+#define MPC831X_SICRL_USB_MASK     0x00000c00
+#define MPC831X_SICRL_USB_ULPI     0x00000800
+#define MPC8315_SICRL_USB_MASK     0x000000fc
+#define MPC8315_SICRL_USB_ULPI     0x00000054
+#define MPC837X_SICRL_USB_MASK     0xf0000000
+#define MPC837X_SICRL_USB_ULPI     0x50000000
+#define MPC837X_SICRL_USBB_MASK    0x30000000
+#define MPC837X_SICRL_SD           0x20000000
+
+/* system i/o configuration register high */
+#define MPC83XX_SICRH_OFFS         0x118
+#define MPC8308_SICRH_USB_MASK     0x000c0000
+#define MPC8308_SICRH_USB_ULPI     0x00040000
+#define MPC834X_SICRH_USB_UTMI     0x00020000
+#define MPC831X_SICRH_USB_MASK     0x000000e0
+#define MPC831X_SICRH_USB_ULPI     0x000000a0
+#define MPC8315_SICRH_USB_MASK     0x0000ff00
+#define MPC8315_SICRH_USB_ULPI     0x00000000
+#define MPC837X_SICRH_SPI_MASK     0x00000003
+#define MPC837X_SICRH_SD           0x00000001
+
+/* USB Control Register */
+#define FSL_USB2_CONTROL_OFFS      0x500
+#define CONTROL_UTMI_PHY_EN        0x00000200
+#define CONTROL_REFSEL_24MHZ       0x00000040
+#define CONTROL_REFSEL_48MHZ       0x00000080
+#define CONTROL_PHY_CLK_SEL_ULPI   0x00000400
+#define CONTROL_OTG_PORT           0x00000020
+
+/* USB PORTSC Registers */
+#define FSL_USB2_PORTSC1_OFFS      0x184
+#define FSL_USB2_PORTSC2_OFFS      0x188
+#define PORTSCX_PTW_16BIT          0x10000000
+#define PORTSCX_PTS_UTMI           0x00000000
+#define PORTSCX_PTS_ULPI           0x80000000
+
+/*
+ * Declaration for the various functions exported by the
+ * mpc83xx_* files. Mostly for use by mpc83xx_setup
+ */
+
+extern void __noreturn mpc83xx_restart(char *cmd);
+extern long mpc83xx_time_init(void);
+int __init mpc837x_usb_cfg(void);
+int __init mpc834x_usb_cfg(void);
+int __init mpc831x_usb_cfg(void);
+extern void mpc83xx_ipic_init_IRQ(void);
+
+#ifdef CONFIG_PCI
+extern void mpc83xx_setup_pci(void);
+#else
+#define mpc83xx_setup_pci	NULL
+#endif
+
+extern int mpc83xx_declare_of_platform_devices(void);
+extern void mpc83xx_setup_arch(void);
+
+#endif				/* __MPC83XX_H__ */

linux-7.2.3/arch/powerpc/platforms/83xx/suspend-asm.S

@@ -0,0 +1,553 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Enter and leave deep sleep state on MPC83xx
+ *
+ * Copyright (c) 2006-2008 Freescale Semiconductor, Inc.
+ * Author: Scott Wood <scottwood@freescale.com>
+ */
+
+#include <asm/page.h>
+#include <asm/ppc_asm.h>
+#include <asm/reg.h>
+#include <asm/asm-offsets.h>
+
+#define SS_MEMSAVE	0x00 /* First 8 bytes of RAM */
+#define SS_HID		0x08 /* 3 HIDs */
+#define SS_IABR		0x14 /* 2 IABRs */
+#define SS_IBCR		0x1c
+#define SS_DABR		0x20 /* 2 DABRs */
+#define SS_DBCR		0x28
+#define SS_SP		0x2c
+#define SS_SR		0x30 /* 16 segment registers */
+#define SS_R2		0x70
+#define SS_MSR		0x74
+#define SS_SDR1		0x78
+#define SS_LR		0x7c
+#define SS_SPRG		0x80 /* 8 SPRGs */
+#define SS_DBAT		0xa0 /* 8 DBATs */
+#define SS_IBAT		0xe0 /* 8 IBATs */
+#define SS_TB		0x120
+#define SS_CR		0x128
+#define SS_GPREG	0x12c /* r12-r31 */
+#define STATE_SAVE_SIZE 0x17c
+
+	.section .data
+	.align	5
+
+mpc83xx_sleep_save_area:
+	.space	STATE_SAVE_SIZE
+immrbase:
+	.long	0
+
+	.section .text
+	.align	5
+
+	/* r3 = physical address of IMMR */
+_GLOBAL(mpc83xx_enter_deep_sleep)
+	lis	r4, immrbase@ha
+	stw	r3, immrbase@l(r4)
+
+	/* The first 2 words of memory are used to communicate with the
+	 * bootloader, to tell it how to resume.
+	 *
+	 * The first word is the magic number 0xf5153ae5, and the second
+	 * is the pointer to mpc83xx_deep_resume.
+	 *
+	 * The original content of these two words is saved in SS_MEMSAVE.
+	 */
+
+	lis	r3, mpc83xx_sleep_save_area@h
+	ori	r3, r3, mpc83xx_sleep_save_area@l
+
+	lis	r4, KERNELBASE@h
+	lwz	r5, 0(r4)
+	lwz	r6, 4(r4)
+
+	stw	r5, SS_MEMSAVE+0(r3)
+	stw	r6, SS_MEMSAVE+4(r3)
+
+	mfspr	r5, SPRN_HID0
+	mfspr	r6, SPRN_HID1
+	/* FIXME: Should this use SPRN_HID2_G2_LE? */
+	mfspr	r7, SPRN_HID2_750FX
+
+	stw	r5, SS_HID+0(r3)
+	stw	r6, SS_HID+4(r3)
+	stw	r7, SS_HID+8(r3)
+
+	mfspr	r4, SPRN_IABR
+	mfspr	r5, SPRN_IABR2
+	mfspr	r6, SPRN_IBCR
+	mfspr	r7, SPRN_DABR
+	mfspr	r8, SPRN_DABR2
+	mfspr	r9, SPRN_DBCR
+
+	stw	r4, SS_IABR+0(r3)
+	stw	r5, SS_IABR+4(r3)
+	stw	r6, SS_IBCR(r3)
+	stw	r7, SS_DABR+0(r3)
+	stw	r8, SS_DABR+4(r3)
+	stw	r9, SS_DBCR(r3)
+
+	mfspr	r4, SPRN_SPRG0
+	mfspr	r5, SPRN_SPRG1
+	mfspr	r6, SPRN_SPRG2
+	mfspr	r7, SPRN_SPRG3
+	mfsdr1	r8
+
+	stw	r4, SS_SPRG+0(r3)
+	stw	r5, SS_SPRG+4(r3)
+	stw	r6, SS_SPRG+8(r3)
+	stw	r7, SS_SPRG+12(r3)
+	stw	r8, SS_SDR1(r3)
+
+	mfspr	r4, SPRN_SPRG4
+	mfspr	r5, SPRN_SPRG5
+	mfspr	r6, SPRN_SPRG6
+	mfspr	r7, SPRN_SPRG7
+
+	stw	r4, SS_SPRG+16(r3)
+	stw	r5, SS_SPRG+20(r3)
+	stw	r6, SS_SPRG+24(r3)
+	stw	r7, SS_SPRG+28(r3)
+
+	mfspr	r4, SPRN_DBAT0U
+	mfspr	r5, SPRN_DBAT0L
+	mfspr	r6, SPRN_DBAT1U
+	mfspr	r7, SPRN_DBAT1L
+
+	stw	r4, SS_DBAT+0x00(r3)
+	stw	r5, SS_DBAT+0x04(r3)
+	stw	r6, SS_DBAT+0x08(r3)
+	stw	r7, SS_DBAT+0x0c(r3)
+
+	mfspr	r4, SPRN_DBAT2U
+	mfspr	r5, SPRN_DBAT2L
+	mfspr	r6, SPRN_DBAT3U
+	mfspr	r7, SPRN_DBAT3L
+
+	stw	r4, SS_DBAT+0x10(r3)
+	stw	r5, SS_DBAT+0x14(r3)
+	stw	r6, SS_DBAT+0x18(r3)
+	stw	r7, SS_DBAT+0x1c(r3)
+
+	mfspr	r4, SPRN_DBAT4U
+	mfspr	r5, SPRN_DBAT4L
+	mfspr	r6, SPRN_DBAT5U
+	mfspr	r7, SPRN_DBAT5L
+
+	stw	r4, SS_DBAT+0x20(r3)
+	stw	r5, SS_DBAT+0x24(r3)
+	stw	r6, SS_DBAT+0x28(r3)
+	stw	r7, SS_DBAT+0x2c(r3)
+
+	mfspr	r4, SPRN_DBAT6U
+	mfspr	r5, SPRN_DBAT6L
+	mfspr	r6, SPRN_DBAT7U
+	mfspr	r7, SPRN_DBAT7L
+
+	stw	r4, SS_DBAT+0x30(r3)
+	stw	r5, SS_DBAT+0x34(r3)
+	stw	r6, SS_DBAT+0x38(r3)
+	stw	r7, SS_DBAT+0x3c(r3)
+
+	mfspr	r4, SPRN_IBAT0U
+	mfspr	r5, SPRN_IBAT0L
+	mfspr	r6, SPRN_IBAT1U
+	mfspr	r7, SPRN_IBAT1L
+
+	stw	r4, SS_IBAT+0x00(r3)
+	stw	r5, SS_IBAT+0x04(r3)
+	stw	r6, SS_IBAT+0x08(r3)
+	stw	r7, SS_IBAT+0x0c(r3)
+
+	mfspr	r4, SPRN_IBAT2U
+	mfspr	r5, SPRN_IBAT2L
+	mfspr	r6, SPRN_IBAT3U
+	mfspr	r7, SPRN_IBAT3L
+
+	stw	r4, SS_IBAT+0x10(r3)
+	stw	r5, SS_IBAT+0x14(r3)
+	stw	r6, SS_IBAT+0x18(r3)
+	stw	r7, SS_IBAT+0x1c(r3)
+
+	mfspr	r4, SPRN_IBAT4U
+	mfspr	r5, SPRN_IBAT4L
+	mfspr	r6, SPRN_IBAT5U
+	mfspr	r7, SPRN_IBAT5L
+
+	stw	r4, SS_IBAT+0x20(r3)
+	stw	r5, SS_IBAT+0x24(r3)
+	stw	r6, SS_IBAT+0x28(r3)
+	stw	r7, SS_IBAT+0x2c(r3)
+
+	mfspr	r4, SPRN_IBAT6U
+	mfspr	r5, SPRN_IBAT6L
+	mfspr	r6, SPRN_IBAT7U
+	mfspr	r7, SPRN_IBAT7L
+
+	stw	r4, SS_IBAT+0x30(r3)
+	stw	r5, SS_IBAT+0x34(r3)
+	stw	r6, SS_IBAT+0x38(r3)
+	stw	r7, SS_IBAT+0x3c(r3)
+
+	mfmsr	r4
+	mflr	r5
+	mfcr	r6
+
+	stw	r4, SS_MSR(r3)
+	stw	r5, SS_LR(r3)
+	stw	r6, SS_CR(r3)
+	stw	r1, SS_SP(r3)
+	stw	r2, SS_R2(r3)
+
+1:	mftbu	r4
+	mftb	r5
+	mftbu	r6
+	cmpw	r4, r6
+	bne	1b
+
+	stw	r4, SS_TB+0(r3)
+	stw	r5, SS_TB+4(r3)
+
+	stmw	r12, SS_GPREG(r3)
+
+	li	r4, 0
+	addi	r6, r3, SS_SR-4
+1:	mfsrin	r5, r4
+	stwu	r5, 4(r6)
+	addis	r4, r4, 0x1000
+	cmpwi	r4, 0
+	bne	1b
+
+	/* Disable machine checks and critical exceptions */
+	mfmsr	r4
+	rlwinm	r4, r4, 0, ~MSR_CE
+	rlwinm	r4, r4, 0, ~MSR_ME
+	mtmsr	r4
+	isync
+
+#define TMP_VIRT_IMMR		0xf0000000
+#define DEFAULT_IMMR_VALUE	0xff400000
+#define IMMRBAR_BASE		0x0000
+
+	lis	r4, immrbase@ha
+	lwz	r4, immrbase@l(r4)
+
+	/* Use DBAT0 to address the current IMMR space */
+
+	ori	r4, r4, 0x002a
+	mtspr	SPRN_DBAT0L, r4
+	lis	r8, TMP_VIRT_IMMR@h
+	ori	r4, r8, 0x001e	/* 1 MByte accessible from Kernel Space only */
+	mtspr	SPRN_DBAT0U, r4
+	isync
+
+	/* Use DBAT1 to address the original IMMR space */
+
+	lis	r4, DEFAULT_IMMR_VALUE@h
+	ori	r4, r4, 0x002a
+	mtspr	SPRN_DBAT1L, r4
+	lis	r9, (TMP_VIRT_IMMR + 0x01000000)@h
+	ori	r4, r9, 0x001e	/* 1 MByte accessible from Kernel Space only */
+	mtspr	SPRN_DBAT1U, r4
+	isync
+
+	/* Use DBAT2 to address the beginning of RAM.  This isn't done
+	 * using the normal virtual mapping, because with page debugging
+	 * enabled it will be read-only.
+	 */
+
+	li	r4, 0x0002
+	mtspr	SPRN_DBAT2L, r4
+	lis	r4, KERNELBASE@h
+	ori	r4, r4, 0x001e	/* 1 MByte accessible from Kernel Space only */
+	mtspr	SPRN_DBAT2U, r4
+	isync
+
+	/* Flush the cache with our BAT, as there will be TLB misses
+	 * otherwise if page debugging is enabled, and these misses
+	 * will disturb the PLRU algorithm.
+	 */
+
+	bl	__flush_disable_L1
+
+	/* Keep the i-cache enabled, so the hack below for low-boot
+	 * flash will work.
+	 */
+	mfspr	r3, SPRN_HID0
+	ori	r3, r3, HID0_ICE
+	mtspr	SPRN_HID0, r3
+	isync
+
+	lis	r6, 0xf515
+	ori	r6, r6, 0x3ae5
+
+	lis	r7, mpc83xx_deep_resume@h
+	ori	r7, r7, mpc83xx_deep_resume@l
+	tophys(r7, r7)
+
+	lis	r5, KERNELBASE@h
+	stw	r6, 0(r5)
+	stw	r7, 4(r5)
+
+	/* Reset BARs */
+
+	li	r4, 0
+	stw	r4, 0x0024(r8)
+	stw	r4, 0x002c(r8)
+	stw	r4, 0x0034(r8)
+	stw	r4, 0x003c(r8)
+	stw	r4, 0x0064(r8)
+	stw	r4, 0x006c(r8)
+
+	/* Rev 1 of the 8313 has problems with wakeup events that are
+	 * pending during the transition to deep sleep state (such as if
+	 * the PCI host sets the state to D3 and then D0 in rapid
+	 * succession).  This check shrinks the race window somewhat.
+	 *
+	 * See erratum PCI23, though the problem is not limited
+	 * to PCI.
+	 */
+
+	lwz	r3, 0x0b04(r8)
+	andi.	r3, r3, 1
+	bne-	mpc83xx_deep_resume
+
+	/* Move IMMR back to the default location, following the
+	 * procedure specified in the MPC8313 manual.
+	 */
+	lwz	r4, IMMRBAR_BASE(r8)
+	isync
+	lis	r4, DEFAULT_IMMR_VALUE@h
+	stw	r4, IMMRBAR_BASE(r8)
+	lis	r4, KERNELBASE@h
+	lwz	r4, 0(r4)
+	isync
+	lwz	r4, IMMRBAR_BASE(r9)
+	mr	r8, r9
+	isync
+
+	/* Check the Reset Configuration Word to see whether flash needs
+	 * to be mapped at a low address or a high address.
+	 */
+
+	lwz	r4, 0x0904(r8)
+	andis.	r4, r4, 0x0400
+	li	r4, 0
+	beq	boot_low
+	lis	r4, 0xff80
+boot_low:
+	stw	r4, 0x0020(r8)
+	lis	r7, 0x8000
+	ori	r7, r7, 0x0016
+
+	mfspr	r5, SPRN_HID0
+	rlwinm	r5, r5, 0, ~(HID0_DOZE | HID0_NAP)
+	oris	r5, r5, HID0_SLEEP@h
+	mtspr	SPRN_HID0, r5
+	isync
+
+	mfmsr	r5
+	oris	r5, r5, MSR_POW@h
+
+	/* Enable the flash mapping at the appropriate address.  This
+	 * mapping will override the RAM mapping if booting low, so there's
+	 * no need to disable the latter.  This must be done inside the same
+	 * cache line as setting MSR_POW, so that no instruction fetches
+	 * from RAM happen after the flash mapping is turned on.
+	 */
+
+	.align	5
+	stw	r7, 0x0024(r8)
+	sync
+	isync
+	mtmsr	r5
+	isync
+1:	b	1b
+
+mpc83xx_deep_resume:
+	lis	r4, 1f@h
+	ori	r4, r4, 1f@l
+	tophys(r4, r4)
+	mtsrr0	r4
+
+	mfmsr	r4
+	rlwinm	r4, r4, 0, ~(MSR_IR | MSR_DR)
+	mtsrr1	r4
+
+	rfi
+
+1:	tlbia
+	bl	__inval_enable_L1
+
+	lis	r3, mpc83xx_sleep_save_area@h
+	ori	r3, r3, mpc83xx_sleep_save_area@l
+	tophys(r3, r3)
+
+	lwz	r5, SS_MEMSAVE+0(r3)
+	lwz	r6, SS_MEMSAVE+4(r3)
+
+	stw	r5, 0(0)
+	stw	r6, 4(0)
+
+	lwz	r5, SS_HID+0(r3)
+	lwz	r6, SS_HID+4(r3)
+	lwz	r7, SS_HID+8(r3)
+
+	mtspr	SPRN_HID0, r5
+	mtspr	SPRN_HID1, r6
+	/* FIXME: Should this use SPRN_HID2_G2_LE? */
+	mtspr	SPRN_HID2_750FX, r7
+
+	lwz	r4, SS_IABR+0(r3)
+	lwz	r5, SS_IABR+4(r3)
+	lwz	r6, SS_IBCR(r3)
+	lwz	r7, SS_DABR+0(r3)
+	lwz	r8, SS_DABR+4(r3)
+	lwz	r9, SS_DBCR(r3)
+
+	mtspr	SPRN_IABR, r4
+	mtspr	SPRN_IABR2, r5
+	mtspr	SPRN_IBCR, r6
+	mtspr	SPRN_DABR, r7
+	mtspr	SPRN_DABR2, r8
+	mtspr	SPRN_DBCR, r9
+
+	li	r4, 0
+	addi	r6, r3, SS_SR-4
+1:	lwzu	r5, 4(r6)
+	mtsrin	r5, r4
+	addis	r4, r4, 0x1000
+	cmpwi	r4, 0
+	bne	1b
+
+	lwz	r4, SS_DBAT+0x00(r3)
+	lwz	r5, SS_DBAT+0x04(r3)
+	lwz	r6, SS_DBAT+0x08(r3)
+	lwz	r7, SS_DBAT+0x0c(r3)
+
+	mtspr	SPRN_DBAT0U, r4
+	mtspr	SPRN_DBAT0L, r5
+	mtspr	SPRN_DBAT1U, r6
+	mtspr	SPRN_DBAT1L, r7
+
+	lwz	r4, SS_DBAT+0x10(r3)
+	lwz	r5, SS_DBAT+0x14(r3)
+	lwz	r6, SS_DBAT+0x18(r3)
+	lwz	r7, SS_DBAT+0x1c(r3)
+
+	mtspr	SPRN_DBAT2U, r4
+	mtspr	SPRN_DBAT2L, r5
+	mtspr	SPRN_DBAT3U, r6
+	mtspr	SPRN_DBAT3L, r7
+
+	lwz	r4, SS_DBAT+0x20(r3)
+	lwz	r5, SS_DBAT+0x24(r3)
+	lwz	r6, SS_DBAT+0x28(r3)
+	lwz	r7, SS_DBAT+0x2c(r3)
+
+	mtspr	SPRN_DBAT4U, r4
+	mtspr	SPRN_DBAT4L, r5
+	mtspr	SPRN_DBAT5U, r6
+	mtspr	SPRN_DBAT5L, r7
+
+	lwz	r4, SS_DBAT+0x30(r3)
+	lwz	r5, SS_DBAT+0x34(r3)
+	lwz	r6, SS_DBAT+0x38(r3)
+	lwz	r7, SS_DBAT+0x3c(r3)
+
+	mtspr	SPRN_DBAT6U, r4
+	mtspr	SPRN_DBAT6L, r5
+	mtspr	SPRN_DBAT7U, r6
+	mtspr	SPRN_DBAT7L, r7
+
+	lwz	r4, SS_IBAT+0x00(r3)
+	lwz	r5, SS_IBAT+0x04(r3)
+	lwz	r6, SS_IBAT+0x08(r3)
+	lwz	r7, SS_IBAT+0x0c(r3)
+
+	mtspr	SPRN_IBAT0U, r4
+	mtspr	SPRN_IBAT0L, r5
+	mtspr	SPRN_IBAT1U, r6
+	mtspr	SPRN_IBAT1L, r7
+
+	lwz	r4, SS_IBAT+0x10(r3)
+	lwz	r5, SS_IBAT+0x14(r3)
+	lwz	r6, SS_IBAT+0x18(r3)
+	lwz	r7, SS_IBAT+0x1c(r3)
+
+	mtspr	SPRN_IBAT2U, r4
+	mtspr	SPRN_IBAT2L, r5
+	mtspr	SPRN_IBAT3U, r6
+	mtspr	SPRN_IBAT3L, r7
+
+	lwz	r4, SS_IBAT+0x20(r3)
+	lwz	r5, SS_IBAT+0x24(r3)
+	lwz	r6, SS_IBAT+0x28(r3)
+	lwz	r7, SS_IBAT+0x2c(r3)
+
+	mtspr	SPRN_IBAT4U, r4
+	mtspr	SPRN_IBAT4L, r5
+	mtspr	SPRN_IBAT5U, r6
+	mtspr	SPRN_IBAT5L, r7
+
+	lwz	r4, SS_IBAT+0x30(r3)
+	lwz	r5, SS_IBAT+0x34(r3)
+	lwz	r6, SS_IBAT+0x38(r3)
+	lwz	r7, SS_IBAT+0x3c(r3)
+
+	mtspr	SPRN_IBAT6U, r4
+	mtspr	SPRN_IBAT6L, r5
+	mtspr	SPRN_IBAT7U, r6
+	mtspr	SPRN_IBAT7L, r7
+
+	lwz	r4, SS_SPRG+16(r3)
+	lwz	r5, SS_SPRG+20(r3)
+	lwz	r6, SS_SPRG+24(r3)
+	lwz	r7, SS_SPRG+28(r3)
+
+	mtspr	SPRN_SPRG4, r4
+	mtspr	SPRN_SPRG5, r5
+	mtspr	SPRN_SPRG6, r6
+	mtspr	SPRN_SPRG7, r7
+
+	lwz	r4, SS_SPRG+0(r3)
+	lwz	r5, SS_SPRG+4(r3)
+	lwz	r6, SS_SPRG+8(r3)
+	lwz	r7, SS_SPRG+12(r3)
+	lwz	r8, SS_SDR1(r3)
+
+	mtspr	SPRN_SPRG0, r4
+	mtspr	SPRN_SPRG1, r5
+	mtspr	SPRN_SPRG2, r6
+	mtspr	SPRN_SPRG3, r7
+	mtsdr1	r8
+
+	lwz	r4, SS_MSR(r3)
+	lwz	r5, SS_LR(r3)
+	lwz	r6, SS_CR(r3)
+	lwz	r1, SS_SP(r3)
+	lwz	r2, SS_R2(r3)
+
+	mtsrr1	r4
+	mtsrr0	r5
+	mtcr	r6
+
+	li	r4, 0
+	mtspr	SPRN_TBWL, r4
+
+	lwz	r4, SS_TB+0(r3)
+	lwz	r5, SS_TB+4(r3)
+
+	mtspr	SPRN_TBWU, r4
+	mtspr	SPRN_TBWL, r5
+
+	lmw	r12, SS_GPREG(r3)
+
+	/* Kick decrementer */
+	li	r0, 1
+	mtdec	r0
+
+	rfi
+_ASM_NOKPROBE_SYMBOL(mpc83xx_deep_resume)

linux-7.2.3/arch/powerpc/platforms/83xx/suspend.c

@@ -0,0 +1,433 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * MPC83xx suspend support
+ *
+ * Author: Scott Wood <scottwood@freescale.com>
+ *
+ * Copyright (c) 2006-2007 Freescale Semiconductor, Inc.
+ */
+
+#include <linux/pm.h>
+#include <linux/types.h>
+#include <linux/ioport.h>
+#include <linux/interrupt.h>
+#include <linux/wait.h>
+#include <linux/sched/signal.h>
+#include <linux/kthread.h>
+#include <linux/freezer.h>
+#include <linux/suspend.h>
+#include <linux/fsl_devices.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/export.h>
+
+#include <asm/reg.h>
+#include <asm/io.h>
+#include <asm/time.h>
+#include <asm/mpc6xx.h>
+#include <asm/switch_to.h>
+
+#include <sysdev/fsl_soc.h>
+
+#define PMCCR1_NEXT_STATE       0x0C /* Next state for power management */
+#define PMCCR1_NEXT_STATE_SHIFT 2
+#define PMCCR1_CURR_STATE       0x03 /* Current state for power management*/
+#define IMMR_SYSCR_OFFSET       0x100
+#define IMMR_RCW_OFFSET         0x900
+#define RCW_PCI_HOST            0x80000000
+
+void mpc83xx_enter_deep_sleep(phys_addr_t immrbase);
+
+struct mpc83xx_pmc {
+	u32 config;
+#define PMCCR_DLPEN 2 /* DDR SDRAM low power enable */
+#define PMCCR_SLPEN 1 /* System low power enable */
+
+	u32 event;
+	u32 mask;
+/* All but PMCI are deep-sleep only */
+#define PMCER_GPIO   0x100
+#define PMCER_PCI    0x080
+#define PMCER_USB    0x040
+#define PMCER_ETSEC1 0x020
+#define PMCER_ETSEC2 0x010
+#define PMCER_TIMER  0x008
+#define PMCER_INT1   0x004
+#define PMCER_INT2   0x002
+#define PMCER_PMCI   0x001
+#define PMCER_ALL    0x1FF
+
+	/* deep-sleep only */
+	u32 config1;
+#define PMCCR1_USE_STATE  0x80000000
+#define PMCCR1_PME_EN     0x00000080
+#define PMCCR1_ASSERT_PME 0x00000040
+#define PMCCR1_POWER_OFF  0x00000020
+
+	/* deep-sleep only */
+	u32 config2;
+};
+
+struct mpc83xx_rcw {
+	u32 rcwlr;
+	u32 rcwhr;
+};
+
+struct mpc83xx_clock {
+	u32 spmr;
+	u32 occr;
+	u32 sccr;
+};
+
+struct mpc83xx_syscr {
+	__be32 sgprl;
+	__be32 sgprh;
+	__be32 spridr;
+	__be32 :32;
+	__be32 spcr;
+	__be32 sicrl;
+	__be32 sicrh;
+};
+
+struct mpc83xx_saved {
+	u32 sicrl;
+	u32 sicrh;
+	u32 sccr;
+};
+
+struct pmc_type {
+	int has_deep_sleep;
+};
+
+static int has_deep_sleep, deep_sleeping;
+static int pmc_irq;
+static struct mpc83xx_pmc __iomem *pmc_regs;
+static struct mpc83xx_clock __iomem *clock_regs;
+static struct mpc83xx_syscr __iomem *syscr_regs;
+static struct mpc83xx_saved saved_regs;
+static int is_pci_agent, wake_from_pci;
+static phys_addr_t immrbase;
+static int pci_pm_state;
+static DECLARE_WAIT_QUEUE_HEAD(agent_wq);
+
+int fsl_deep_sleep(void)
+{
+	return deep_sleeping;
+}
+EXPORT_SYMBOL(fsl_deep_sleep);
+
+static int mpc83xx_change_state(void)
+{
+	u32 curr_state;
+	u32 reg_cfg1 = in_be32(&pmc_regs->config1);
+
+	if (is_pci_agent) {
+		pci_pm_state = (reg_cfg1 & PMCCR1_NEXT_STATE) >>
+		               PMCCR1_NEXT_STATE_SHIFT;
+		curr_state = reg_cfg1 & PMCCR1_CURR_STATE;
+
+		if (curr_state != pci_pm_state) {
+			reg_cfg1 &= ~PMCCR1_CURR_STATE;
+			reg_cfg1 |= pci_pm_state;
+			out_be32(&pmc_regs->config1, reg_cfg1);
+
+			wake_up(&agent_wq);
+			return 1;
+		}
+	}
+
+	return 0;
+}
+
+static irqreturn_t pmc_irq_handler(int irq, void *dev_id)
+{
+	u32 event = in_be32(&pmc_regs->event);
+	int ret = IRQ_NONE;
+
+	if (mpc83xx_change_state())
+		ret = IRQ_HANDLED;
+
+	if (event) {
+		out_be32(&pmc_regs->event, event);
+		ret = IRQ_HANDLED;
+	}
+
+	return ret;
+}
+
+static void mpc83xx_suspend_restore_regs(void)
+{
+	out_be32(&syscr_regs->sicrl, saved_regs.sicrl);
+	out_be32(&syscr_regs->sicrh, saved_regs.sicrh);
+	out_be32(&clock_regs->sccr, saved_regs.sccr);
+}
+
+static void mpc83xx_suspend_save_regs(void)
+{
+	saved_regs.sicrl = in_be32(&syscr_regs->sicrl);
+	saved_regs.sicrh = in_be32(&syscr_regs->sicrh);
+	saved_regs.sccr = in_be32(&clock_regs->sccr);
+}
+
+static int mpc83xx_suspend_enter(suspend_state_t state)
+{
+	int ret = -EAGAIN;
+
+	/* Don't go to sleep if there's a race where pci_pm_state changes
+	 * between the agent thread checking it and the PM code disabling
+	 * interrupts.
+	 */
+	if (wake_from_pci) {
+		if (pci_pm_state != (deep_sleeping ? 3 : 2))
+			goto out;
+
+		out_be32(&pmc_regs->config1,
+		         in_be32(&pmc_regs->config1) | PMCCR1_PME_EN);
+	}
+
+	/* Put the system into low-power mode and the RAM
+	 * into self-refresh mode once the core goes to
+	 * sleep.
+	 */
+
+	out_be32(&pmc_regs->config, PMCCR_SLPEN | PMCCR_DLPEN);
+
+	/* If it has deep sleep (i.e. it's an 831x or compatible),
+	 * disable power to the core upon entering sleep mode.  This will
+	 * require going through the boot firmware upon a wakeup event.
+	 */
+
+	if (deep_sleeping) {
+		mpc83xx_suspend_save_regs();
+
+		out_be32(&pmc_regs->mask, PMCER_ALL);
+
+		out_be32(&pmc_regs->config1,
+		         in_be32(&pmc_regs->config1) | PMCCR1_POWER_OFF);
+
+		if (IS_ENABLED(CONFIG_PPC_FPU))
+			enable_kernel_fp();
+
+		mpc83xx_enter_deep_sleep(immrbase);
+
+		out_be32(&pmc_regs->config1,
+		         in_be32(&pmc_regs->config1) & ~PMCCR1_POWER_OFF);
+
+		out_be32(&pmc_regs->mask, PMCER_PMCI);
+
+		mpc83xx_suspend_restore_regs();
+	} else {
+		out_be32(&pmc_regs->mask, PMCER_PMCI);
+
+		mpc6xx_enter_standby();
+	}
+
+	ret = 0;
+
+out:
+	out_be32(&pmc_regs->config1,
+	         in_be32(&pmc_regs->config1) & ~PMCCR1_PME_EN);
+
+	return ret;
+}
+
+static void mpc83xx_suspend_end(void)
+{
+	deep_sleeping = 0;
+}
+
+static int mpc83xx_suspend_valid(suspend_state_t state)
+{
+	return state == PM_SUSPEND_STANDBY || state == PM_SUSPEND_MEM;
+}
+
+static int mpc83xx_suspend_begin(suspend_state_t state)
+{
+	switch (state) {
+		case PM_SUSPEND_STANDBY:
+			deep_sleeping = 0;
+			return 0;
+
+		case PM_SUSPEND_MEM:
+			if (has_deep_sleep)
+				deep_sleeping = 1;
+
+			return 0;
+
+		default:
+			return -EINVAL;
+	}
+}
+
+static int agent_thread_fn(void *data)
+{
+	set_freezable();
+
+	while (1) {
+		wait_event_freezable(agent_wq, pci_pm_state >= 2);
+
+		if (signal_pending(current) || pci_pm_state < 2)
+			continue;
+
+		/* With a preemptible kernel (or SMP), this could race with
+		 * a userspace-driven suspend request.  It's probably best
+		 * to avoid mixing the two with such a configuration (or
+		 * else fix it by adding a mutex to state_store that we can
+		 * synchronize with).
+		 */
+
+		wake_from_pci = 1;
+
+		pm_suspend(pci_pm_state == 3 ? PM_SUSPEND_MEM :
+		                               PM_SUSPEND_STANDBY);
+
+		wake_from_pci = 0;
+	}
+
+	return 0;
+}
+
+static void mpc83xx_set_agent(void)
+{
+	out_be32(&pmc_regs->config1, PMCCR1_USE_STATE);
+	out_be32(&pmc_regs->mask, PMCER_PMCI);
+
+	kthread_run(agent_thread_fn, NULL, "PCI power mgt");
+}
+
+static int mpc83xx_is_pci_agent(void)
+{
+	struct mpc83xx_rcw __iomem *rcw_regs;
+	int ret;
+
+	rcw_regs = ioremap(get_immrbase() + IMMR_RCW_OFFSET,
+	                   sizeof(struct mpc83xx_rcw));
+
+	if (!rcw_regs)
+		return -ENOMEM;
+
+	ret = !(in_be32(&rcw_regs->rcwhr) & RCW_PCI_HOST);
+
+	iounmap(rcw_regs);
+	return ret;
+}
+
+static const struct platform_suspend_ops mpc83xx_suspend_ops = {
+	.valid = mpc83xx_suspend_valid,
+	.begin = mpc83xx_suspend_begin,
+	.enter = mpc83xx_suspend_enter,
+	.end = mpc83xx_suspend_end,
+};
+
+static struct pmc_type pmc_types[] = {
+	{
+		.has_deep_sleep = 1,
+	},
+	{
+		.has_deep_sleep = 0,
+	}
+};
+
+static const struct of_device_id pmc_match[] = {
+	{
+		.compatible = "fsl,mpc8313-pmc",
+		.data = &pmc_types[0],
+	},
+	{
+		.compatible = "fsl,mpc8349-pmc",
+		.data = &pmc_types[1],
+	},
+	{}
+};
+
+static int pmc_probe(struct platform_device *ofdev)
+{
+	struct device_node *np = ofdev->dev.of_node;
+	struct resource res;
+	const struct pmc_type *type;
+	int ret = 0;
+
+	type = of_device_get_match_data(&ofdev->dev);
+	if (!type)
+		return -EINVAL;
+
+	if (!of_device_is_available(np))
+		return -ENODEV;
+
+	has_deep_sleep = type->has_deep_sleep;
+	immrbase = get_immrbase();
+
+	is_pci_agent = mpc83xx_is_pci_agent();
+	if (is_pci_agent < 0)
+		return is_pci_agent;
+
+	ret = of_address_to_resource(np, 0, &res);
+	if (ret)
+		return -ENODEV;
+
+	pmc_irq = irq_of_parse_and_map(np, 0);
+	if (pmc_irq) {
+		ret = request_irq(pmc_irq, pmc_irq_handler, IRQF_SHARED,
+		                  "pmc", ofdev);
+
+		if (ret)
+			return -EBUSY;
+	}
+
+	pmc_regs = ioremap(res.start, sizeof(*pmc_regs));
+
+	if (!pmc_regs) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	ret = of_address_to_resource(np, 1, &res);
+	if (ret) {
+		ret = -ENODEV;
+		goto out_pmc;
+	}
+
+	clock_regs = ioremap(res.start, sizeof(*clock_regs));
+
+	if (!clock_regs) {
+		ret = -ENOMEM;
+		goto out_pmc;
+	}
+
+	if (has_deep_sleep) {
+		syscr_regs = ioremap(immrbase + IMMR_SYSCR_OFFSET,
+				     sizeof(*syscr_regs));
+		if (!syscr_regs) {
+			ret = -ENOMEM;
+			goto out_syscr;
+		}
+	}
+
+	if (is_pci_agent)
+		mpc83xx_set_agent();
+
+	suspend_set_ops(&mpc83xx_suspend_ops);
+	return 0;
+
+out_syscr:
+	iounmap(clock_regs);
+out_pmc:
+	iounmap(pmc_regs);
+out:
+	if (pmc_irq)
+		free_irq(pmc_irq, ofdev);
+
+	return ret;
+}
+
+static struct platform_driver pmc_driver = {
+	.driver = {
+		.name = "mpc83xx-pmc",
+		.of_match_table = pmc_match,
+		.suppress_bind_attrs = true,
+	},
+	.probe = pmc_probe,
+};
+
+builtin_platform_driver(pmc_driver);

linux-7.2.3/arch/powerpc/platforms/83xx/usb_831x.c

@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Freescale 83xx USB SOC setup code
+ *
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Author: Li Yang
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/io.h>
+
+#include <sysdev/fsl_soc.h>
+
+#include "mpc83xx.h"
+
+int __init mpc831x_usb_cfg(void)
+{
+	u32 temp;
+	void __iomem *immap, *usb_regs;
+	struct device_node *np = NULL;
+	struct device_node *immr_node = NULL;
+	const void *prop;
+	struct resource res;
+	int ret = 0;
+#ifdef CONFIG_USB_OTG
+	const void *dr_mode;
+#endif
+
+	np = of_find_compatible_node(NULL, NULL, "fsl-usb2-dr");
+	if (!np)
+		return -ENODEV;
+	prop = of_get_property(np, "phy_type", NULL);
+
+	/* Map IMMR space for pin and clock settings */
+	immap = ioremap(get_immrbase(), 0x1000);
+	if (!immap) {
+		of_node_put(np);
+		return -ENOMEM;
+	}
+
+	/* Configure clock */
+	immr_node = of_get_parent(np);
+	if (immr_node && (of_device_is_compatible(immr_node, "fsl,mpc8315-immr") ||
+			  of_device_is_compatible(immr_node, "fsl,mpc8308-immr")))
+		clrsetbits_be32(immap + MPC83XX_SCCR_OFFS,
+				MPC8315_SCCR_USB_MASK,
+				MPC8315_SCCR_USB_DRCM_01);
+	else
+		clrsetbits_be32(immap + MPC83XX_SCCR_OFFS,
+				MPC83XX_SCCR_USB_MASK,
+				MPC83XX_SCCR_USB_DRCM_11);
+
+	/* Configure pin mux for ULPI.  There is no pin mux for UTMI */
+	if (prop && !strcmp(prop, "ulpi")) {
+		if (of_device_is_compatible(immr_node, "fsl,mpc8308-immr")) {
+			clrsetbits_be32(immap + MPC83XX_SICRH_OFFS,
+					MPC8308_SICRH_USB_MASK,
+					MPC8308_SICRH_USB_ULPI);
+		} else if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr")) {
+			clrsetbits_be32(immap + MPC83XX_SICRL_OFFS,
+					MPC8315_SICRL_USB_MASK,
+					MPC8315_SICRL_USB_ULPI);
+			clrsetbits_be32(immap + MPC83XX_SICRH_OFFS,
+					MPC8315_SICRH_USB_MASK,
+					MPC8315_SICRH_USB_ULPI);
+		} else {
+			clrsetbits_be32(immap + MPC83XX_SICRL_OFFS,
+					MPC831X_SICRL_USB_MASK,
+					MPC831X_SICRL_USB_ULPI);
+			clrsetbits_be32(immap + MPC83XX_SICRH_OFFS,
+					MPC831X_SICRH_USB_MASK,
+					MPC831X_SICRH_USB_ULPI);
+		}
+	}
+
+	iounmap(immap);
+
+	of_node_put(immr_node);
+
+	/* Map USB SOC space */
+	ret = of_address_to_resource(np, 0, &res);
+	if (ret) {
+		of_node_put(np);
+		return ret;
+	}
+	usb_regs = ioremap(res.start, resource_size(&res));
+
+	/* Using on-chip PHY */
+	if (prop && (!strcmp(prop, "utmi_wide") || !strcmp(prop, "utmi"))) {
+		u32 refsel;
+
+		if (of_device_is_compatible(immr_node, "fsl,mpc8308-immr"))
+			goto out;
+
+		if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr"))
+			refsel = CONTROL_REFSEL_24MHZ;
+		else
+			refsel = CONTROL_REFSEL_48MHZ;
+		/* Set UTMI_PHY_EN and REFSEL */
+		out_be32(usb_regs + FSL_USB2_CONTROL_OFFS,
+			 CONTROL_UTMI_PHY_EN | refsel);
+	/* Using external UPLI PHY */
+	} else if (prop && !strcmp(prop, "ulpi")) {
+		/* Set PHY_CLK_SEL to ULPI */
+		temp = CONTROL_PHY_CLK_SEL_ULPI;
+#ifdef CONFIG_USB_OTG
+		/* Set OTG_PORT */
+		if (!of_device_is_compatible(immr_node, "fsl,mpc8308-immr")) {
+			dr_mode = of_get_property(np, "dr_mode", NULL);
+			if (dr_mode && !strcmp(dr_mode, "otg"))
+				temp |= CONTROL_OTG_PORT;
+		}
+#endif /* CONFIG_USB_OTG */
+		out_be32(usb_regs + FSL_USB2_CONTROL_OFFS, temp);
+	} else {
+		pr_warn("831x USB PHY type not supported\n");
+		ret = -EINVAL;
+	}
+
+out:
+	iounmap(usb_regs);
+	of_node_put(np);
+	return ret;
+}

linux-7.2.3/arch/powerpc/platforms/83xx/usb_834x.c

@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Freescale 83xx USB SOC setup code
+ *
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Author: Li Yang
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/io.h>
+
+#include <sysdev/fsl_soc.h>
+
+#include "mpc83xx.h"
+
+int __init mpc834x_usb_cfg(void)
+{
+	unsigned long sccr, sicrl, sicrh;
+	void __iomem *immap;
+	struct device_node *np = NULL;
+	int port0_is_dr = 0, port1_is_dr = 0;
+	const void *prop, *dr_mode;
+
+	immap = ioremap(get_immrbase(), 0x1000);
+	if (!immap)
+		return -ENOMEM;
+
+	/* Read registers */
+	/* Note: DR and MPH must use the same clock setting in SCCR */
+	sccr = in_be32(immap + MPC83XX_SCCR_OFFS) & ~MPC83XX_SCCR_USB_MASK;
+	sicrl = in_be32(immap + MPC83XX_SICRL_OFFS) & ~MPC834X_SICRL_USB_MASK;
+	sicrh = in_be32(immap + MPC83XX_SICRH_OFFS) & ~MPC834X_SICRH_USB_UTMI;
+
+	np = of_find_compatible_node(NULL, NULL, "fsl-usb2-dr");
+	if (np) {
+		sccr |= MPC83XX_SCCR_USB_DRCM_11;  /* 1:3 */
+
+		prop = of_get_property(np, "phy_type", NULL);
+		port1_is_dr = 1;
+		if (prop &&
+		    (!strcmp(prop, "utmi") || !strcmp(prop, "utmi_wide"))) {
+			sicrl |= MPC834X_SICRL_USB0 | MPC834X_SICRL_USB1;
+			sicrh |= MPC834X_SICRH_USB_UTMI;
+			port0_is_dr = 1;
+		} else if (prop && !strcmp(prop, "serial")) {
+			dr_mode = of_get_property(np, "dr_mode", NULL);
+			if (dr_mode && !strcmp(dr_mode, "otg")) {
+				sicrl |= MPC834X_SICRL_USB0 | MPC834X_SICRL_USB1;
+				port0_is_dr = 1;
+			} else {
+				sicrl |= MPC834X_SICRL_USB1;
+			}
+		} else if (prop && !strcmp(prop, "ulpi")) {
+			sicrl |= MPC834X_SICRL_USB1;
+		} else {
+			pr_warn("834x USB PHY type not supported\n");
+		}
+		of_node_put(np);
+	}
+	np = of_find_compatible_node(NULL, NULL, "fsl-usb2-mph");
+	if (np) {
+		sccr |= MPC83XX_SCCR_USB_MPHCM_11; /* 1:3 */
+
+		prop = of_get_property(np, "port0", NULL);
+		if (prop) {
+			if (port0_is_dr)
+				pr_warn("834x USB port0 can't be used by both DR and MPH!\n");
+			sicrl &= ~MPC834X_SICRL_USB0;
+		}
+		prop = of_get_property(np, "port1", NULL);
+		if (prop) {
+			if (port1_is_dr)
+				pr_warn("834x USB port1 can't be used by both DR and MPH!\n");
+			sicrl &= ~MPC834X_SICRL_USB1;
+		}
+		of_node_put(np);
+	}
+
+	/* Write back */
+	out_be32(immap + MPC83XX_SCCR_OFFS, sccr);
+	out_be32(immap + MPC83XX_SICRL_OFFS, sicrl);
+	out_be32(immap + MPC83XX_SICRH_OFFS, sicrh);
+
+	iounmap(immap);
+	return 0;
+}

linux-7.2.3/arch/powerpc/platforms/83xx/usb_837x.c

@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Freescale 83xx USB SOC setup code
+ *
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ * Author: Li Yang
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/io.h>
+
+#include <sysdev/fsl_soc.h>
+
+#include "mpc83xx.h"
+
+int __init mpc837x_usb_cfg(void)
+{
+	void __iomem *immap;
+	struct device_node *np = NULL;
+	const void *prop;
+	int ret = 0;
+
+	np = of_find_compatible_node(NULL, NULL, "fsl-usb2-dr");
+	if (!np || !of_device_is_available(np)) {
+		of_node_put(np);
+		return -ENODEV;
+	}
+	prop = of_get_property(np, "phy_type", NULL);
+
+	if (!prop || (strcmp(prop, "ulpi") && strcmp(prop, "serial"))) {
+		pr_warn("837x USB PHY type not supported\n");
+		of_node_put(np);
+		return -EINVAL;
+	}
+
+	/* Map IMMR space for pin and clock settings */
+	immap = ioremap(get_immrbase(), 0x1000);
+	if (!immap) {
+		of_node_put(np);
+		return -ENOMEM;
+	}
+
+	/* Configure clock */
+	clrsetbits_be32(immap + MPC83XX_SCCR_OFFS, MPC837X_SCCR_USB_DRCM_11,
+			MPC837X_SCCR_USB_DRCM_11);
+
+	/* Configure pin mux for ULPI/serial */
+	clrsetbits_be32(immap + MPC83XX_SICRL_OFFS, MPC837X_SICRL_USB_MASK,
+			MPC837X_SICRL_USB_ULPI);
+
+	iounmap(immap);
+	of_node_put(np);
+	return ret;
+}