Resguardo inicial

linux-7.2.3/drivers/gpu/drm/aspeed/Kconfig

@@ -0,0 +1,17 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config DRM_ASPEED_GFX
+	tristate "ASPEED BMC Display Controller"
+	depends on DRM && OF
+	depends on (COMPILE_TEST || ARCH_ASPEED)
+	depends on MMU
+	select DRM_CLIENT_SELECTION
+	select DRM_KMS_HELPER
+	select DRM_GEM_DMA_HELPER
+	select DMA_CMA if HAVE_DMA_CONTIGUOUS
+	select CMA if HAVE_DMA_CONTIGUOUS
+	select MFD_SYSCON
+	help
+	  Chose this option if you have an ASPEED AST2500 SOC Display
+	  Controller (aka GFX).
+
+	  If M is selected this module will be called aspeed_gfx.

linux-7.2.3/drivers/gpu/drm/aspeed/Makefile

@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
+aspeed_gfx-y := aspeed_gfx_drv.o aspeed_gfx_crtc.o aspeed_gfx_out.o
+
+obj-$(CONFIG_DRM_ASPEED_GFX) += aspeed_gfx.o

linux-7.2.3/drivers/gpu/drm/aspeed/aspeed_gfx.h

@@ -0,0 +1,108 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/* Copyright 2018 IBM Corporation */
+
+#include <drm/drm_device.h>
+#include <drm/drm_simple_kms_helper.h>
+
+struct aspeed_gfx {
+	struct drm_device		drm;
+	void __iomem			*base;
+	struct clk			*clk;
+	struct reset_control		*rst;
+	struct regmap			*scu;
+
+	u32				dac_reg;
+	u32				int_clr_reg;
+	u32				vga_scratch_reg;
+	u32				throd_val;
+	u32				scan_line_max;
+
+	struct drm_simple_display_pipe	pipe;
+	struct drm_connector		connector;
+};
+#define to_aspeed_gfx(x) container_of(x, struct aspeed_gfx, drm)
+
+int aspeed_gfx_create_pipe(struct drm_device *drm);
+int aspeed_gfx_create_output(struct drm_device *drm);
+
+#define CRT_CTRL1		0x60 /* CRT Control I */
+#define CRT_CTRL2		0x64 /* CRT Control II */
+#define CRT_STATUS		0x68 /* CRT Status */
+#define CRT_MISC		0x6c /* CRT Misc Setting */
+#define CRT_HORIZ0		0x70 /* CRT Horizontal Total & Display Enable End */
+#define CRT_HORIZ1		0x74 /* CRT Horizontal Retrace Start & End */
+#define CRT_VERT0		0x78 /* CRT Vertical Total & Display Enable End */
+#define CRT_VERT1		0x7C /* CRT Vertical Retrace Start & End */
+#define CRT_ADDR		0x80 /* CRT Display Starting Address */
+#define CRT_OFFSET		0x84 /* CRT Display Offset & Terminal Count */
+#define CRT_THROD		0x88 /* CRT Threshold */
+#define CRT_XSCALE		0x8C /* CRT Scaling-Up Factor */
+#define CRT_CURSOR0		0x90 /* CRT Hardware Cursor X & Y Offset */
+#define CRT_CURSOR1		0x94 /* CRT Hardware Cursor X & Y Position */
+#define CRT_CURSOR2		0x98 /* CRT Hardware Cursor Pattern Address */
+#define CRT_9C			0x9C
+#define CRT_OSD_H		0xA0 /* CRT OSD Horizontal Start/End */
+#define CRT_OSD_V		0xA4 /* CRT OSD Vertical Start/End */
+#define CRT_OSD_ADDR		0xA8 /* CRT OSD Pattern Address */
+#define CRT_OSD_DISP		0xAC /* CRT OSD Offset */
+#define CRT_OSD_THRESH		0xB0 /* CRT OSD Threshold & Alpha */
+#define CRT_B4			0xB4
+#define CRT_STS_V		0xB8 /* CRT Status V */
+#define CRT_SCRATCH		0xBC /* Scratchpad */
+#define CRT_BB0_ADDR		0xD0 /* CRT Display BB0 Starting Address */
+#define CRT_BB1_ADDR		0xD4 /* CRT Display BB1 Starting Address */
+#define CRT_BB_COUNT		0xD8 /* CRT Display BB Terminal Count */
+#define OSD_COLOR1		0xE0 /* OSD Color Palette Index 1 & 0 */
+#define OSD_COLOR2		0xE4 /* OSD Color Palette Index 3 & 2 */
+#define OSD_COLOR3		0xE8 /* OSD Color Palette Index 5 & 4 */
+#define OSD_COLOR4		0xEC /* OSD Color Palette Index 7 & 6 */
+#define OSD_COLOR5		0xF0 /* OSD Color Palette Index 9 & 8 */
+#define OSD_COLOR6		0xF4 /* OSD Color Palette Index 11 & 10 */
+#define OSD_COLOR7		0xF8 /* OSD Color Palette Index 13 & 12 */
+#define OSD_COLOR8		0xFC /* OSD Color Palette Index 15 & 14 */
+
+/* CTRL1 */
+#define CRT_CTRL_EN			BIT(0)
+#define CRT_CTRL_HW_CURSOR_EN		BIT(1)
+#define CRT_CTRL_OSD_EN			BIT(2)
+#define CRT_CTRL_INTERLACED		BIT(3)
+#define CRT_CTRL_COLOR_RGB565		(0 << 7)
+#define CRT_CTRL_COLOR_YUV444		(1 << 7)
+#define CRT_CTRL_COLOR_XRGB8888		(2 << 7)
+#define CRT_CTRL_COLOR_RGB888		(3 << 7)
+#define CRT_CTRL_COLOR_YUV444_2RGB	(5 << 7)
+#define CRT_CTRL_COLOR_YUV422		(7 << 7)
+#define CRT_CTRL_COLOR_MASK		GENMASK(9, 7)
+#define CRT_CTRL_HSYNC_NEGATIVE		BIT(16)
+#define CRT_CTRL_VSYNC_NEGATIVE		BIT(17)
+#define CRT_CTRL_VERTICAL_INTR_EN	BIT(30)
+#define CRT_CTRL_VERTICAL_INTR_STS	BIT(31)
+
+/* CTRL2 */
+#define CRT_CTRL_DAC_EN			BIT(0)
+#define CRT_CTRL_VBLANK_LINE(x)		(((x) << 20) & CRT_CTRL_VBLANK_LINE_MASK)
+#define CRT_CTRL_VBLANK_LINE_MASK	GENMASK(31, 20)
+
+/* CRT_HORIZ0 */
+#define CRT_H_TOTAL(x)			(x)
+#define CRT_H_DE(x)			((x) << 16)
+
+/* CRT_HORIZ1 */
+#define CRT_H_RS_START(x)		(x)
+#define CRT_H_RS_END(x)			((x) << 16)
+
+/* CRT_VIRT0 */
+#define CRT_V_TOTAL(x)			(x)
+#define CRT_V_DE(x)			((x) << 16)
+
+/* CRT_VIRT1 */
+#define CRT_V_RS_START(x)		(x)
+#define CRT_V_RS_END(x)			((x) << 16)
+
+/* CRT_OFFSET */
+#define CRT_DISP_OFFSET(x)		(x)
+#define CRT_TERM_COUNT(x)		((x) << 16)
+
+/* CRT_THROD */
+#define CRT_THROD_LOW(x)		(x)
+#define CRT_THROD_HIGH(x)		((x) << 8)

linux-7.2.3/drivers/gpu/drm/aspeed/aspeed_gfx_crtc.c

@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright 2018 IBM Corporation
+
+#include <linux/clk.h>
+#include <linux/reset.h>
+#include <linux/regmap.h>
+
+#include <drm/drm_device.h>
+#include <drm/drm_fb_dma_helper.h>
+#include <drm/drm_fourcc.h>
+#include <drm/drm_framebuffer.h>
+#include <drm/drm_gem_atomic_helper.h>
+#include <drm/drm_gem_dma_helper.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_simple_kms_helper.h>
+#include <drm/drm_vblank.h>
+
+#include "aspeed_gfx.h"
+
+static struct aspeed_gfx *
+drm_pipe_to_aspeed_gfx(struct drm_simple_display_pipe *pipe)
+{
+	return container_of(pipe, struct aspeed_gfx, pipe);
+}
+
+static int aspeed_gfx_set_pixel_fmt(struct aspeed_gfx *priv, u32 *bpp)
+{
+	struct drm_crtc *crtc = &priv->pipe.crtc;
+	struct drm_device *drm = crtc->dev;
+	const u32 format = crtc->primary->state->fb->format->format;
+	u32 ctrl1;
+
+	ctrl1 = readl(priv->base + CRT_CTRL1);
+	ctrl1 &= ~CRT_CTRL_COLOR_MASK;
+
+	switch (format) {
+	case DRM_FORMAT_RGB565:
+		dev_dbg(drm->dev, "Setting up RGB565 mode\n");
+		ctrl1 |= CRT_CTRL_COLOR_RGB565;
+		*bpp = 16;
+		break;
+	case DRM_FORMAT_XRGB8888:
+		dev_dbg(drm->dev, "Setting up XRGB8888 mode\n");
+		ctrl1 |= CRT_CTRL_COLOR_XRGB8888;
+		*bpp = 32;
+		break;
+	default:
+		dev_err(drm->dev, "Unhandled pixel format %08x\n", format);
+		return -EINVAL;
+	}
+
+	writel(ctrl1, priv->base + CRT_CTRL1);
+
+	return 0;
+}
+
+static void aspeed_gfx_enable_controller(struct aspeed_gfx *priv)
+{
+	u32 ctrl1 = readl(priv->base + CRT_CTRL1);
+	u32 ctrl2 = readl(priv->base + CRT_CTRL2);
+
+	/* Set DAC source for display output to Graphics CRT (GFX) */
+	regmap_update_bits(priv->scu, priv->dac_reg, BIT(16), BIT(16));
+
+	writel(ctrl1 | CRT_CTRL_EN, priv->base + CRT_CTRL1);
+	writel(ctrl2 | CRT_CTRL_DAC_EN, priv->base + CRT_CTRL2);
+}
+
+static void aspeed_gfx_disable_controller(struct aspeed_gfx *priv)
+{
+	u32 ctrl1 = readl(priv->base + CRT_CTRL1);
+	u32 ctrl2 = readl(priv->base + CRT_CTRL2);
+
+	writel(ctrl1 & ~CRT_CTRL_EN, priv->base + CRT_CTRL1);
+	writel(ctrl2 & ~CRT_CTRL_DAC_EN, priv->base + CRT_CTRL2);
+
+	regmap_update_bits(priv->scu, priv->dac_reg, BIT(16), 0);
+}
+
+static void aspeed_gfx_crtc_mode_set_nofb(struct aspeed_gfx *priv)
+{
+	struct drm_display_mode *m = &priv->pipe.crtc.state->adjusted_mode;
+	u32 ctrl1, d_offset, t_count, bpp;
+	int err;
+
+	err = aspeed_gfx_set_pixel_fmt(priv, &bpp);
+	if (err)
+		return;
+
+#if 0
+	/* TODO: we have only been able to test with the 40MHz USB clock. The
+	 * clock is fixed, so we cannot adjust it here. */
+	clk_set_rate(priv->pixel_clk, m->crtc_clock * 1000);
+#endif
+
+	ctrl1 = readl(priv->base + CRT_CTRL1);
+	ctrl1 &= ~(CRT_CTRL_INTERLACED |
+			CRT_CTRL_HSYNC_NEGATIVE |
+			CRT_CTRL_VSYNC_NEGATIVE);
+
+	if (m->flags & DRM_MODE_FLAG_INTERLACE)
+		ctrl1 |= CRT_CTRL_INTERLACED;
+
+	if (!(m->flags & DRM_MODE_FLAG_PHSYNC))
+		ctrl1 |= CRT_CTRL_HSYNC_NEGATIVE;
+
+	if (!(m->flags & DRM_MODE_FLAG_PVSYNC))
+		ctrl1 |= CRT_CTRL_VSYNC_NEGATIVE;
+
+	writel(ctrl1, priv->base + CRT_CTRL1);
+
+	/* Horizontal timing */
+	writel(CRT_H_TOTAL(m->htotal - 1) | CRT_H_DE(m->hdisplay - 1),
+			priv->base + CRT_HORIZ0);
+	writel(CRT_H_RS_START(m->hsync_start - 1) | CRT_H_RS_END(m->hsync_end),
+			priv->base + CRT_HORIZ1);
+
+
+	/* Vertical timing */
+	writel(CRT_V_TOTAL(m->vtotal - 1) | CRT_V_DE(m->vdisplay - 1),
+			priv->base + CRT_VERT0);
+	writel(CRT_V_RS_START(m->vsync_start) | CRT_V_RS_END(m->vsync_end),
+			priv->base + CRT_VERT1);
+
+	/*
+	 * Display Offset: address difference between consecutive scan lines
+	 * Terminal Count: memory size of one scan line
+	 */
+	d_offset = m->hdisplay * bpp / 8;
+	t_count = DIV_ROUND_UP(m->hdisplay * bpp, priv->scan_line_max);
+
+	writel(CRT_DISP_OFFSET(d_offset) | CRT_TERM_COUNT(t_count),
+			priv->base + CRT_OFFSET);
+
+	/*
+	 * Threshold: FIFO thresholds of refill and stop (16 byte chunks
+	 * per line, rounded up)
+	 */
+	writel(priv->throd_val, priv->base + CRT_THROD);
+}
+
+static void aspeed_gfx_pipe_enable(struct drm_simple_display_pipe *pipe,
+			      struct drm_crtc_state *crtc_state,
+			      struct drm_plane_state *plane_state)
+{
+	struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe);
+	struct drm_crtc *crtc = &pipe->crtc;
+
+	aspeed_gfx_crtc_mode_set_nofb(priv);
+	aspeed_gfx_enable_controller(priv);
+	drm_crtc_vblank_on(crtc);
+}
+
+static void aspeed_gfx_pipe_disable(struct drm_simple_display_pipe *pipe)
+{
+	struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe);
+	struct drm_crtc *crtc = &pipe->crtc;
+
+	drm_crtc_vblank_off(crtc);
+	aspeed_gfx_disable_controller(priv);
+}
+
+static void aspeed_gfx_pipe_update(struct drm_simple_display_pipe *pipe,
+				   struct drm_plane_state *plane_state)
+{
+	struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe);
+	struct drm_crtc *crtc = &pipe->crtc;
+	struct drm_framebuffer *fb = pipe->plane.state->fb;
+	struct drm_pending_vblank_event *event;
+	struct drm_gem_dma_object *gem;
+
+	spin_lock_irq(&crtc->dev->event_lock);
+	event = crtc->state->event;
+	if (event) {
+		crtc->state->event = NULL;
+
+		if (drm_crtc_vblank_get(crtc) == 0)
+			drm_crtc_arm_vblank_event(crtc, event);
+		else
+			drm_crtc_send_vblank_event(crtc, event);
+	}
+	spin_unlock_irq(&crtc->dev->event_lock);
+
+	if (!fb)
+		return;
+
+	gem = drm_fb_dma_get_gem_obj(fb, 0);
+	if (!gem)
+		return;
+	writel(gem->dma_addr, priv->base + CRT_ADDR);
+}
+
+static int aspeed_gfx_enable_vblank(struct drm_simple_display_pipe *pipe)
+{
+	struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe);
+	u32 reg = readl(priv->base + CRT_CTRL1);
+
+	/* Clear pending VBLANK IRQ */
+	writel(reg | CRT_CTRL_VERTICAL_INTR_STS, priv->base + CRT_CTRL1);
+
+	reg |= CRT_CTRL_VERTICAL_INTR_EN;
+	writel(reg, priv->base + CRT_CTRL1);
+
+	return 0;
+}
+
+static void aspeed_gfx_disable_vblank(struct drm_simple_display_pipe *pipe)
+{
+	struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe);
+	u32 reg = readl(priv->base + CRT_CTRL1);
+
+	reg &= ~CRT_CTRL_VERTICAL_INTR_EN;
+	writel(reg, priv->base + CRT_CTRL1);
+
+	/* Clear pending VBLANK IRQ */
+	writel(reg | CRT_CTRL_VERTICAL_INTR_STS, priv->base + CRT_CTRL1);
+}
+
+static const struct drm_simple_display_pipe_funcs aspeed_gfx_funcs = {
+	.enable		= aspeed_gfx_pipe_enable,
+	.disable	= aspeed_gfx_pipe_disable,
+	.update		= aspeed_gfx_pipe_update,
+	.enable_vblank	= aspeed_gfx_enable_vblank,
+	.disable_vblank	= aspeed_gfx_disable_vblank,
+};
+
+static const uint32_t aspeed_gfx_formats[] = {
+	DRM_FORMAT_XRGB8888,
+	DRM_FORMAT_RGB565,
+};
+
+int aspeed_gfx_create_pipe(struct drm_device *drm)
+{
+	struct aspeed_gfx *priv = to_aspeed_gfx(drm);
+
+	return drm_simple_display_pipe_init(drm, &priv->pipe, &aspeed_gfx_funcs,
+					    aspeed_gfx_formats,
+					    ARRAY_SIZE(aspeed_gfx_formats),
+					    NULL,
+					    &priv->connector);
+}

linux-7.2.3/drivers/gpu/drm/aspeed/aspeed_gfx_drv.c

@@ -0,0 +1,379 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright 2018 IBM Corporation
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/irq.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <drm/clients/drm_client_setup.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_device.h>
+#include <drm/drm_fbdev_dma.h>
+#include <drm/drm_gem_dma_helper.h>
+#include <drm/drm_gem_framebuffer_helper.h>
+#include <drm/drm_module.h>
+#include <drm/drm_probe_helper.h>
+#include <drm/drm_simple_kms_helper.h>
+#include <drm/drm_vblank.h>
+#include <drm/drm_drv.h>
+
+#include "aspeed_gfx.h"
+
+/**
+ * DOC: ASPEED GFX Driver
+ *
+ * This driver is for the ASPEED BMC SoC's 'GFX' display hardware, also called
+ * the 'SOC Display Controller' in the datasheet. This driver runs on the ARM
+ * based BMC systems, unlike the ast driver which runs on a host CPU and is for
+ * a PCIe graphics device.
+ *
+ * The AST2500 supports a total of 3 output paths:
+ *
+ *   1. VGA output, the output target can choose either or both to the DAC
+ *   or DVO interface.
+ *
+ *   2. Graphics CRT output, the output target can choose either or both to
+ *   the DAC or DVO interface.
+ *
+ *   3. Video input from DVO, the video input can be used for video engine
+ *   capture or DAC display output.
+ *
+ * Output options are selected in SCU2C.
+ *
+ * The "VGA mode" device is the PCI attached controller. The "Graphics CRT"
+ * is the ARM's internal display controller.
+ *
+ * The driver only supports a simple configuration consisting of a 40MHz
+ * pixel clock, fixed by hardware limitations, and the VGA output path.
+ *
+ * The driver was written with the 'AST2500 Software Programming Guide' v17,
+ * which is available under NDA from ASPEED.
+ */
+
+struct aspeed_gfx_config {
+	u32 dac_reg;		/* DAC register in SCU */
+	u32 int_clear_reg;	/* Interrupt clear register */
+	u32 vga_scratch_reg;	/* VGA scratch register in SCU */
+	u32 throd_val;		/* Default Threshold Seting */
+	u32 scan_line_max;	/* Max memory size of one scan line */
+};
+
+static const struct aspeed_gfx_config ast2400_config = {
+	.dac_reg = 0x2c,
+	.int_clear_reg = 0x60,
+	.vga_scratch_reg = 0x50,
+	.throd_val = CRT_THROD_LOW(0x1e) | CRT_THROD_HIGH(0x12),
+	.scan_line_max = 64,
+};
+
+static const struct aspeed_gfx_config ast2500_config = {
+	.dac_reg = 0x2c,
+	.int_clear_reg = 0x60,
+	.vga_scratch_reg = 0x50,
+	.throd_val = CRT_THROD_LOW(0x24) | CRT_THROD_HIGH(0x3c),
+	.scan_line_max = 128,
+};
+
+static const struct aspeed_gfx_config ast2600_config = {
+	.dac_reg = 0xc0,
+	.int_clear_reg = 0x68,
+	.vga_scratch_reg = 0x50,
+	.throd_val = CRT_THROD_LOW(0x50) | CRT_THROD_HIGH(0x70),
+	.scan_line_max = 128,
+};
+
+static const struct of_device_id aspeed_gfx_match[] = {
+	{ .compatible = "aspeed,ast2400-gfx", .data = &ast2400_config },
+	{ .compatible = "aspeed,ast2500-gfx", .data = &ast2500_config },
+	{ .compatible = "aspeed,ast2600-gfx", .data = &ast2600_config },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, aspeed_gfx_match);
+
+static const struct drm_mode_config_funcs aspeed_gfx_mode_config_funcs = {
+	.fb_create		= drm_gem_fb_create,
+	.atomic_check		= drm_atomic_helper_check,
+	.atomic_commit		= drm_atomic_helper_commit,
+};
+
+static int aspeed_gfx_setup_mode_config(struct drm_device *drm)
+{
+	int ret;
+
+	ret = drmm_mode_config_init(drm);
+	if (ret)
+		return ret;
+
+	drm->mode_config.min_width = 0;
+	drm->mode_config.min_height = 0;
+	drm->mode_config.max_width = 800;
+	drm->mode_config.max_height = 600;
+	drm->mode_config.funcs = &aspeed_gfx_mode_config_funcs;
+
+	return ret;
+}
+
+static irqreturn_t aspeed_gfx_irq_handler(int irq, void *data)
+{
+	struct drm_device *drm = data;
+	struct aspeed_gfx *priv = to_aspeed_gfx(drm);
+	u32 reg;
+
+	reg = readl(priv->base + CRT_CTRL1);
+
+	if (reg & CRT_CTRL_VERTICAL_INTR_STS) {
+		drm_crtc_handle_vblank(&priv->pipe.crtc);
+		writel(reg, priv->base + priv->int_clr_reg);
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
+static int aspeed_gfx_load(struct drm_device *drm)
+{
+	struct platform_device *pdev = to_platform_device(drm->dev);
+	struct aspeed_gfx *priv = to_aspeed_gfx(drm);
+	struct device_node *np = pdev->dev.of_node;
+	const struct aspeed_gfx_config *config;
+	int ret;
+
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	config = device_get_match_data(&pdev->dev);
+	if (!config)
+		return -EINVAL;
+
+	priv->dac_reg = config->dac_reg;
+	priv->int_clr_reg = config->int_clear_reg;
+	priv->vga_scratch_reg = config->vga_scratch_reg;
+	priv->throd_val = config->throd_val;
+	priv->scan_line_max = config->scan_line_max;
+
+	priv->scu = syscon_regmap_lookup_by_phandle(np, "syscon");
+	if (IS_ERR(priv->scu)) {
+		priv->scu = syscon_regmap_lookup_by_compatible("aspeed,ast2500-scu");
+		if (IS_ERR(priv->scu)) {
+			dev_err(&pdev->dev, "failed to find SCU regmap\n");
+			return PTR_ERR(priv->scu);
+		}
+	}
+
+	ret = of_reserved_mem_device_init(drm->dev);
+	if (ret) {
+		dev_err(&pdev->dev,
+			"failed to initialize reserved mem: %d\n", ret);
+		return ret;
+	}
+
+	ret = dma_set_mask_and_coherent(drm->dev, DMA_BIT_MASK(32));
+	if (ret) {
+		dev_err(&pdev->dev, "failed to set DMA mask: %d\n", ret);
+		return ret;
+	}
+
+	priv->rst = devm_reset_control_get_exclusive(&pdev->dev, NULL);
+	if (IS_ERR(priv->rst)) {
+		dev_err(&pdev->dev,
+			"missing or invalid reset controller device tree entry");
+		return PTR_ERR(priv->rst);
+	}
+	reset_control_deassert(priv->rst);
+
+	priv->clk = devm_clk_get(drm->dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		dev_err(&pdev->dev,
+			"missing or invalid clk device tree entry");
+		return PTR_ERR(priv->clk);
+	}
+	clk_prepare_enable(priv->clk);
+
+	/* Sanitize control registers */
+	writel(0, priv->base + CRT_CTRL1);
+	writel(0, priv->base + CRT_CTRL2);
+
+	ret = aspeed_gfx_setup_mode_config(drm);
+	if (ret < 0)
+		return ret;
+
+	ret = drm_vblank_init(drm, 1);
+	if (ret < 0) {
+		dev_err(drm->dev, "Failed to initialise vblank\n");
+		return ret;
+	}
+
+	ret = aspeed_gfx_create_output(drm);
+	if (ret < 0) {
+		dev_err(drm->dev, "Failed to create outputs\n");
+		return ret;
+	}
+
+	ret = aspeed_gfx_create_pipe(drm);
+	if (ret < 0) {
+		dev_err(drm->dev, "Cannot setup simple display pipe\n");
+		return ret;
+	}
+
+	ret = devm_request_irq(drm->dev, platform_get_irq(pdev, 0),
+			       aspeed_gfx_irq_handler, 0, "aspeed gfx", drm);
+	if (ret < 0) {
+		dev_err(drm->dev, "Failed to install IRQ handler\n");
+		return ret;
+	}
+
+	drm_mode_config_reset(drm);
+
+	return 0;
+}
+
+static void aspeed_gfx_unload(struct drm_device *drm)
+{
+	drm_kms_helper_poll_fini(drm);
+}
+
+DEFINE_DRM_GEM_DMA_FOPS(fops);
+
+static const struct drm_driver aspeed_gfx_driver = {
+	.driver_features        = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC,
+	DRM_GEM_DMA_DRIVER_OPS,
+	DRM_FBDEV_DMA_DRIVER_OPS,
+	.fops = &fops,
+	.name = "aspeed-gfx-drm",
+	.desc = "ASPEED GFX DRM",
+	.major = 1,
+	.minor = 0,
+};
+
+static ssize_t dac_mux_store(struct device *dev, struct device_attribute *attr,
+			     const char *buf, size_t count)
+{
+	struct aspeed_gfx *priv = dev_get_drvdata(dev);
+	u32 val;
+	int rc;
+
+	rc = kstrtou32(buf, 0, &val);
+	if (rc)
+		return rc;
+
+	if (val > 3)
+		return -EINVAL;
+
+	rc = regmap_update_bits(priv->scu, priv->dac_reg, 0x30000, val << 16);
+	if (rc < 0)
+		return 0;
+
+	return count;
+}
+
+static ssize_t dac_mux_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct aspeed_gfx *priv = dev_get_drvdata(dev);
+	u32 reg;
+	int rc;
+
+	rc = regmap_read(priv->scu, priv->dac_reg, &reg);
+	if (rc)
+		return rc;
+
+	return sprintf(buf, "%u\n", (reg >> 16) & 0x3);
+}
+static DEVICE_ATTR_RW(dac_mux);
+
+static ssize_t
+vga_pw_show(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct aspeed_gfx *priv = dev_get_drvdata(dev);
+	u32 reg;
+	int rc;
+
+	rc = regmap_read(priv->scu, priv->vga_scratch_reg, &reg);
+	if (rc)
+		return rc;
+
+	return sprintf(buf, "%u\n", reg);
+}
+static DEVICE_ATTR_RO(vga_pw);
+
+static struct attribute *aspeed_sysfs_entries[] = {
+	&dev_attr_vga_pw.attr,
+	&dev_attr_dac_mux.attr,
+	NULL,
+};
+
+static struct attribute_group aspeed_sysfs_attr_group = {
+	.attrs = aspeed_sysfs_entries,
+};
+
+static int aspeed_gfx_probe(struct platform_device *pdev)
+{
+	struct aspeed_gfx *priv;
+	int ret;
+
+	priv = devm_drm_dev_alloc(&pdev->dev, &aspeed_gfx_driver,
+				  struct aspeed_gfx, drm);
+	if (IS_ERR(priv))
+		return PTR_ERR(priv);
+
+	ret = aspeed_gfx_load(&priv->drm);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, priv);
+
+	ret = sysfs_create_group(&pdev->dev.kobj, &aspeed_sysfs_attr_group);
+	if (ret)
+		return ret;
+
+	ret = drm_dev_register(&priv->drm, 0);
+	if (ret)
+		goto err_unload;
+
+	drm_client_setup(&priv->drm, NULL);
+	return 0;
+
+err_unload:
+	sysfs_remove_group(&pdev->dev.kobj, &aspeed_sysfs_attr_group);
+	aspeed_gfx_unload(&priv->drm);
+
+	return ret;
+}
+
+static void aspeed_gfx_remove(struct platform_device *pdev)
+{
+	struct drm_device *drm = platform_get_drvdata(pdev);
+
+	sysfs_remove_group(&pdev->dev.kobj, &aspeed_sysfs_attr_group);
+	drm_dev_unregister(drm);
+	aspeed_gfx_unload(drm);
+	drm_atomic_helper_shutdown(drm);
+}
+
+static void aspeed_gfx_shutdown(struct platform_device *pdev)
+{
+	drm_atomic_helper_shutdown(platform_get_drvdata(pdev));
+}
+
+static struct platform_driver aspeed_gfx_platform_driver = {
+	.probe		= aspeed_gfx_probe,
+	.remove		= aspeed_gfx_remove,
+	.shutdown	= aspeed_gfx_shutdown,
+	.driver = {
+		.name = "aspeed_gfx",
+		.of_match_table = aspeed_gfx_match,
+	},
+};
+
+drm_module_platform_driver(aspeed_gfx_platform_driver);
+
+MODULE_AUTHOR("Joel Stanley <joel@jms.id.au>");
+MODULE_DESCRIPTION("ASPEED BMC DRM/KMS driver");
+MODULE_LICENSE("GPL");

linux-7.2.3/drivers/gpu/drm/aspeed/aspeed_gfx_out.c

@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright 2018 IBM Corporation
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_connector.h>
+#include <drm/drm_edid.h>
+#include <drm/drm_probe_helper.h>
+
+#include "aspeed_gfx.h"
+
+static int aspeed_gfx_get_modes(struct drm_connector *connector)
+{
+	return drm_add_modes_noedid(connector, 800, 600);
+}
+
+static const struct
+drm_connector_helper_funcs aspeed_gfx_connector_helper_funcs = {
+	.get_modes = aspeed_gfx_get_modes,
+};
+
+static const struct drm_connector_funcs aspeed_gfx_connector_funcs = {
+	.fill_modes		= drm_helper_probe_single_connector_modes,
+	.destroy		= drm_connector_cleanup,
+	.reset			= drm_atomic_helper_connector_reset,
+	.atomic_duplicate_state	= drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state	= drm_atomic_helper_connector_destroy_state,
+};
+
+int aspeed_gfx_create_output(struct drm_device *drm)
+{
+	struct aspeed_gfx *priv = to_aspeed_gfx(drm);
+	int ret;
+
+	priv->connector.dpms = DRM_MODE_DPMS_OFF;
+	priv->connector.polled = 0;
+	drm_connector_helper_add(&priv->connector,
+				 &aspeed_gfx_connector_helper_funcs);
+	ret = drm_connector_init(drm, &priv->connector,
+				 &aspeed_gfx_connector_funcs,
+				 DRM_MODE_CONNECTOR_Unknown);
+	return ret;
+}