Resguardo inicial

linux-7.2.3/drivers/media/platform/ti/Kconfig

@@ -0,0 +1,96 @@
+# SPDX-License-Identifier: GPL-2.0-only
+
+comment "Texas Instruments drivers"
+
+# TI VIDEO PORT Helper Modules
+# These will be selected by VPE and VIP
+config VIDEO_TI_VPDMA
+	tristate
+
+config VIDEO_TI_SC
+	tristate
+
+config VIDEO_TI_CSC
+	tristate
+
+# V4L drivers
+
+config VIDEO_TI_CAL
+	tristate "TI CAL (Camera Adaptation Layer) driver"
+	depends on VIDEO_DEV
+	depends on V4L_PLATFORM_DRIVERS
+	select MEDIA_CONTROLLER
+	select VIDEO_V4L2_SUBDEV_API
+	depends on SOC_DRA7XX || ARCH_K3 || COMPILE_TEST
+	select VIDEOBUF2_DMA_CONTIG
+	select V4L2_FWNODE
+	help
+	  Support for the TI CAL (Camera Adaptation Layer) block
+	  found on DRA72X SoC.
+	  In TI Technical Reference Manual this module is referred as
+	  Camera Interface Subsystem (CAMSS).
+
+config VIDEO_TI_CAL_MC
+	bool "Media Controller centric mode by default"
+	depends on VIDEO_TI_CAL
+	default n
+	help
+	  Enables Media Controller centric mode by default.
+
+	  If set, CAL driver will start in Media Controller mode by
+	  default. Note that this behavior can be overridden via
+	  module parameter 'mc_api'.
+
+config VIDEO_TI_VIP
+        tristate "TI Video Input Port"
+        depends on VIDEO_DEV
+        depends on SOC_DRA7XX || COMPILE_TEST
+        depends on HAS_DMA
+        select VIDEOBUF2_DMA_CONTIG
+        select VIDEO_TI_VPDMA
+        select VIDEO_TI_SC
+        select VIDEO_TI_CSC
+        help
+        Driver support for VIP module on certain TI SoC's
+        VIP = Video Input Port.
+
+# Mem2mem drivers
+
+config VIDEO_TI_VPE
+	tristate "TI VPE (Video Processing Engine) driver"
+	depends on V4L_MEM2MEM_DRIVERS
+	depends on VIDEO_DEV
+	depends on SOC_DRA7XX || COMPILE_TEST
+	select VIDEOBUF2_DMA_CONTIG
+	select V4L2_MEM2MEM_DEV
+	select VIDEO_TI_VPDMA
+	select VIDEO_TI_SC
+	select VIDEO_TI_CSC
+	help
+	  Support for the TI VPE(Video Processing Engine) block
+	  found on DRA7XX SoC.
+
+config VIDEO_TI_VPE_DEBUG
+	bool "VPE debug messages"
+	depends on VIDEO_TI_VPE
+	help
+	  Enable debug messages on VPE driver.
+
+config VIDEO_TI_J721E_CSI2RX
+	tristate "TI J721E CSI2RX wrapper layer driver"
+	depends on VIDEO_DEV && VIDEO_V4L2_SUBDEV_API
+	depends on MEDIA_SUPPORT && MEDIA_CONTROLLER
+	depends on VIDEO_CADENCE_CSI2RX
+	depends on PHY_CADENCE_DPHY_RX || COMPILE_TEST
+	depends on ARCH_K3 || COMPILE_TEST
+	depends on PM
+	select VIDEOBUF2_DMA_CONTIG
+	select V4L2_FWNODE
+	help
+	  Support for TI CSI2RX wrapper layer. This just enables the wrapper driver.
+	  The Cadence CSI2RX bridge driver needs to be enabled separately.
+
+source "drivers/media/platform/ti/am437x/Kconfig"
+source "drivers/media/platform/ti/davinci/Kconfig"
+source "drivers/media/platform/ti/omap/Kconfig"
+source "drivers/media/platform/ti/omap3isp/Kconfig"

linux-7.2.3/drivers/media/platform/ti/Makefile

@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-y += am437x/
+obj-y += cal/
+obj-y += vpe/
+obj-y += davinci/
+obj-y += j721e-csi2rx/
+obj-y += omap/
+obj-y += omap3isp/

linux-7.2.3/drivers/media/platform/ti/am437x/Kconfig

@@ -0,0 +1,16 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config VIDEO_AM437X_VPFE
+	tristate "TI AM437x VPFE video capture driver"
+	depends on V4L_PLATFORM_DRIVERS
+	depends on VIDEO_DEV
+	depends on SOC_AM43XX || COMPILE_TEST
+	select MEDIA_CONTROLLER
+	select VIDEO_V4L2_SUBDEV_API
+	select VIDEOBUF2_DMA_CONTIG
+	select V4L2_FWNODE
+	help
+	   Support for AM437x Video Processing Front End based Video
+	   Capture Driver.
+
+	   To compile this driver as a module, choose M here. The module
+	   will be called am437x-vpfe.

linux-7.2.3/drivers/media/platform/ti/am437x/Makefile

@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
+# Makefile for AM437x VPFE driver
+
+obj-$(CONFIG_VIDEO_AM437X_VPFE) += am437x-vpfe.o

linux-7.2.3/drivers/media/platform/ti/am437x/am437x-vpfe.h

@@ -0,0 +1,288 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2013 - 2014 Texas Instruments, Inc.
+ *
+ * Benoit Parrot <bparrot@ti.com>
+ * Lad, Prabhakar <prabhakar.csengg@gmail.com>
+ */
+
+#ifndef AM437X_VPFE_H
+#define AM437X_VPFE_H
+
+#include <linux/am437x-vpfe.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/i2c.h>
+#include <linux/videodev2.h>
+
+#include <media/v4l2-dev.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-ioctl.h>
+#include <media/videobuf2-v4l2.h>
+#include <media/videobuf2-dma-contig.h>
+
+#include "am437x-vpfe_regs.h"
+
+enum vpfe_pin_pol {
+	VPFE_PINPOL_POSITIVE = 0,
+	VPFE_PINPOL_NEGATIVE,
+};
+
+enum vpfe_hw_if_type {
+	/* Raw Bayer */
+	VPFE_RAW_BAYER = 0,
+	/* BT656 - 8 bit */
+	VPFE_BT656,
+	/* BT656 - 10 bit */
+	VPFE_BT656_10BIT,
+	/* YCbCr - 8 bit with external sync */
+	VPFE_YCBCR_SYNC_8,
+	/* YCbCr - 16 bit with external sync */
+	VPFE_YCBCR_SYNC_16,
+};
+
+/* interface description */
+struct vpfe_hw_if_param {
+	enum vpfe_hw_if_type if_type;
+	enum vpfe_pin_pol hdpol;
+	enum vpfe_pin_pol vdpol;
+	unsigned int bus_width;
+};
+
+#define VPFE_MAX_SUBDEV		1
+#define VPFE_MAX_INPUTS		1
+
+struct vpfe_std_info {
+	int active_pixels;
+	int active_lines;
+	/* current frame format */
+	int frame_format;
+};
+
+struct vpfe_route {
+	u32 input;
+	u32 output;
+};
+
+struct vpfe_subdev_info {
+	/* Sub device group id */
+	int grp_id;
+	/* inputs available at the sub device */
+	struct v4l2_input inputs[VPFE_MAX_INPUTS];
+	/* Sub dev routing information for each input */
+	struct vpfe_route *routes;
+	/* check if sub dev supports routing */
+	int can_route;
+	/* ccdc bus/interface configuration */
+	struct vpfe_hw_if_param vpfe_param;
+	struct v4l2_subdev *sd;
+};
+
+struct vpfe_config {
+	/* information about each subdev */
+	struct vpfe_subdev_info sub_devs[VPFE_MAX_SUBDEV];
+	/* Flat array, arranged in groups */
+	struct v4l2_async_connection *asd[VPFE_MAX_SUBDEV];
+};
+
+struct vpfe_cap_buffer {
+	struct vb2_v4l2_buffer vb;
+	struct list_head list;
+};
+
+enum ccdc_pixfmt {
+	CCDC_PIXFMT_RAW = 0,
+	CCDC_PIXFMT_YCBCR_16BIT,
+	CCDC_PIXFMT_YCBCR_8BIT,
+};
+
+enum ccdc_frmfmt {
+	CCDC_FRMFMT_PROGRESSIVE = 0,
+	CCDC_FRMFMT_INTERLACED,
+};
+
+/* PIXEL ORDER IN MEMORY from LSB to MSB */
+/* only applicable for 8-bit input mode  */
+enum ccdc_pixorder {
+	CCDC_PIXORDER_YCBYCR,
+	CCDC_PIXORDER_CBYCRY,
+};
+
+enum ccdc_buftype {
+	CCDC_BUFTYPE_FLD_INTERLEAVED,
+	CCDC_BUFTYPE_FLD_SEPARATED
+};
+
+
+/* returns the highest bit used for the gamma */
+static inline u8 ccdc_gamma_width_max_bit(enum vpfe_ccdc_gamma_width width)
+{
+	return 15 - width;
+}
+
+/* returns the highest bit used for this data size */
+static inline u8 ccdc_data_size_max_bit(enum vpfe_ccdc_data_size sz)
+{
+	return sz == VPFE_CCDC_DATA_8BITS ? 7 : 15 - sz;
+}
+
+/* Structure for CCDC configuration parameters for raw capture mode */
+struct ccdc_params_raw {
+	/* pixel format */
+	enum ccdc_pixfmt pix_fmt;
+	/* progressive or interlaced frame */
+	enum ccdc_frmfmt frm_fmt;
+	struct v4l2_rect win;
+	/* Current Format Bytes Per Pixels */
+	unsigned int bytesperpixel;
+	/* Current Format Bytes per Lines
+	 * (Aligned to 32 bytes) used for HORZ_INFO
+	 */
+	unsigned int bytesperline;
+	/* field id polarity */
+	enum vpfe_pin_pol fid_pol;
+	/* vertical sync polarity */
+	enum vpfe_pin_pol vd_pol;
+	/* horizontal sync polarity */
+	enum vpfe_pin_pol hd_pol;
+	/* interleaved or separated fields */
+	enum ccdc_buftype buf_type;
+	/*
+	 * enable to store the image in inverse
+	 * order in memory(bottom to top)
+	 */
+	unsigned char image_invert_enable;
+	/* configurable parameters */
+	struct vpfe_ccdc_config_params_raw config_params;
+};
+
+struct ccdc_params_ycbcr {
+	/* pixel format */
+	enum ccdc_pixfmt pix_fmt;
+	/* progressive or interlaced frame */
+	enum ccdc_frmfmt frm_fmt;
+	struct v4l2_rect win;
+	/* Current Format Bytes Per Pixels */
+	unsigned int bytesperpixel;
+	/* Current Format Bytes per Lines
+	 * (Aligned to 32 bytes) used for HORZ_INFO
+	 */
+	unsigned int bytesperline;
+	/* field id polarity */
+	enum vpfe_pin_pol fid_pol;
+	/* vertical sync polarity */
+	enum vpfe_pin_pol vd_pol;
+	/* horizontal sync polarity */
+	enum vpfe_pin_pol hd_pol;
+	/* enable BT.656 embedded sync mode */
+	int bt656_enable;
+	/* cb:y:cr:y or y:cb:y:cr in memory */
+	enum ccdc_pixorder pix_order;
+	/* interleaved or separated fields  */
+	enum ccdc_buftype buf_type;
+};
+
+/*
+ * CCDC operational configuration
+ */
+struct ccdc_config {
+	/* CCDC interface type */
+	enum vpfe_hw_if_type if_type;
+	/* Raw Bayer configuration */
+	struct ccdc_params_raw bayer;
+	/* YCbCr configuration */
+	struct ccdc_params_ycbcr ycbcr;
+	/* ccdc base address */
+	void __iomem *base_addr;
+};
+
+struct vpfe_ccdc {
+	struct ccdc_config ccdc_cfg;
+	u32 ccdc_ctx[VPFE_REG_END / sizeof(u32)];
+};
+
+/*
+ * struct vpfe_fmt - VPFE media bus format information
+ * fourcc: V4L2 pixel format code
+ * code: V4L2 media bus format code
+ * bitsperpixel: Bits per pixel over the bus
+ */
+struct vpfe_fmt {
+	u32 fourcc;
+	u32 code;
+	u32 bitsperpixel;
+};
+
+/*
+ * When formats[] is modified make sure to adjust this value also.
+ * Expect compile time warnings if VPFE_NUM_FORMATS is smaller then
+ * the number of elements in formats[].
+ */
+#define VPFE_NUM_FORMATS	10
+
+struct vpfe_device {
+	/* V4l2 specific parameters */
+	/* Identifies video device for this channel */
+	struct video_device video_dev;
+	/* sub devices */
+	struct v4l2_subdev **sd;
+	/* vpfe cfg */
+	struct vpfe_config *cfg;
+	/* V4l2 device */
+	struct v4l2_device v4l2_dev;
+	/* parent device */
+	struct device *pdev;
+	/* subdevice async Notifier */
+	struct v4l2_async_notifier notifier;
+	/* Indicates id of the field which is being displayed */
+	unsigned field;
+	unsigned sequence;
+	/* current interface type */
+	struct vpfe_hw_if_param vpfe_if_params;
+	/* ptr to currently selected sub device */
+	struct vpfe_subdev_info *current_subdev;
+	/* current input at the sub device */
+	int current_input;
+	/* Keeps track of the information about the standard */
+	struct vpfe_std_info std_info;
+	/* std index into std table */
+	int std_index;
+	/* IRQs used when CCDC output to SDRAM */
+	unsigned int irq;
+	/* Pointer pointing to current v4l2_buffer */
+	struct vpfe_cap_buffer *cur_frm;
+	/* Pointer pointing to next v4l2_buffer */
+	struct vpfe_cap_buffer *next_frm;
+	/* Used to store pixel format */
+	struct v4l2_format fmt;
+	/* Used to keep a reference to the current vpfe_fmt */
+	struct vpfe_fmt *current_vpfe_fmt;
+	struct vpfe_fmt	*active_fmt[VPFE_NUM_FORMATS];
+	unsigned int num_active_fmt;
+
+	/*
+	 * used when IMP is chained to store the crop window which
+	 * is different from the image window
+	 */
+	struct v4l2_rect crop;
+	/* Buffer queue used in vb2 */
+	struct vb2_queue buffer_queue;
+	/* Queue of filled frames */
+	struct list_head dma_queue;
+	/* IRQ lock for DMA queue */
+	spinlock_t dma_queue_lock;
+	/* lock used to access this structure */
+	struct mutex lock;
+	/*
+	 * offset where second field starts from the starting of the
+	 * buffer for field separated YCbCr formats
+	 */
+	u32 field_off;
+	struct vpfe_ccdc ccdc;
+	int stopping;
+	struct completion capture_stop;
+};
+
+#endif	/* AM437X_VPFE_H */

linux-7.2.3/drivers/media/platform/ti/am437x/am437x-vpfe_regs.h

@@ -0,0 +1,132 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * TI AM437x Image Sensor Interface Registers
+ *
+ * Copyright (C) 2013 - 2014 Texas Instruments, Inc.
+ *
+ * Benoit Parrot <bparrot@ti.com>
+ * Lad, Prabhakar <prabhakar.csengg@gmail.com>
+ */
+
+#ifndef AM437X_VPFE_REGS_H
+#define AM437X_VPFE_REGS_H
+
+/* VPFE module register offset */
+#define VPFE_REVISION				0x0
+#define VPFE_PCR				0x4
+#define VPFE_SYNMODE				0x8
+#define VPFE_HD_VD_WID				0xc
+#define VPFE_PIX_LINES				0x10
+#define VPFE_HORZ_INFO				0x14
+#define VPFE_VERT_START				0x18
+#define VPFE_VERT_LINES				0x1c
+#define VPFE_CULLING				0x20
+#define VPFE_HSIZE_OFF				0x24
+#define VPFE_SDOFST				0x28
+#define VPFE_SDR_ADDR				0x2c
+#define VPFE_CLAMP				0x30
+#define VPFE_DCSUB				0x34
+#define VPFE_COLPTN				0x38
+#define VPFE_BLKCMP				0x3c
+#define VPFE_VDINT				0x48
+#define VPFE_ALAW				0x4c
+#define VPFE_REC656IF				0x50
+#define VPFE_CCDCFG				0x54
+#define VPFE_DMA_CNTL				0x98
+#define VPFE_SYSCONFIG				0x104
+#define VPFE_CONFIG				0x108
+#define VPFE_IRQ_EOI				0x110
+#define VPFE_IRQ_STS_RAW			0x114
+#define VPFE_IRQ_STS				0x118
+#define VPFE_IRQ_EN_SET				0x11c
+#define VPFE_IRQ_EN_CLR				0x120
+#define VPFE_REG_END				0x124
+
+/* Define bit fields within selected registers */
+#define VPFE_FID_POL_MASK			1
+#define VPFE_FID_POL_SHIFT			4
+#define VPFE_HD_POL_MASK			1
+#define VPFE_HD_POL_SHIFT			3
+#define VPFE_VD_POL_MASK			1
+#define VPFE_VD_POL_SHIFT			2
+#define VPFE_HSIZE_OFF_MASK			0xffffffe0
+#define VPFE_32BYTE_ALIGN_VAL			31
+#define VPFE_FRM_FMT_MASK			0x1
+#define VPFE_FRM_FMT_SHIFT			7
+#define VPFE_DATA_SZ_MASK			7
+#define VPFE_DATA_SZ_SHIFT			8
+#define VPFE_PIX_FMT_MASK			3
+#define VPFE_PIX_FMT_SHIFT			12
+#define VPFE_VP2SDR_DISABLE			0xfffbffff
+#define VPFE_WEN_ENABLE				BIT(17)
+#define VPFE_SDR2RSZ_DISABLE			0xfff7ffff
+#define VPFE_VDHDEN_ENABLE			BIT(16)
+#define VPFE_LPF_ENABLE				BIT(14)
+#define VPFE_ALAW_ENABLE			BIT(3)
+#define VPFE_ALAW_GAMMA_WD_MASK			7
+#define VPFE_BLK_CLAMP_ENABLE			BIT(31)
+#define VPFE_BLK_SGAIN_MASK			0x1f
+#define VPFE_BLK_ST_PXL_MASK			0x7fff
+#define VPFE_BLK_ST_PXL_SHIFT			10
+#define VPFE_BLK_SAMPLE_LN_MASK			7
+#define VPFE_BLK_SAMPLE_LN_SHIFT		28
+#define VPFE_BLK_SAMPLE_LINE_MASK		7
+#define VPFE_BLK_SAMPLE_LINE_SHIFT		25
+#define VPFE_BLK_DC_SUB_MASK			0x03fff
+#define VPFE_BLK_COMP_MASK			0xff
+#define VPFE_BLK_COMP_GB_COMP_SHIFT		8
+#define VPFE_BLK_COMP_GR_COMP_SHIFT		16
+#define VPFE_BLK_COMP_R_COMP_SHIFT		24
+#define VPFE_LATCH_ON_VSYNC_DISABLE		BIT(15)
+#define VPFE_DATA_PACK_ENABLE			BIT(11)
+#define VPFE_HORZ_INFO_SPH_SHIFT		16
+#define VPFE_VERT_START_SLV0_SHIFT		16
+#define VPFE_VDINT_VDINT0_SHIFT			16
+#define VPFE_VDINT_VDINT1_MASK			0xffff
+#define VPFE_PPC_RAW				1
+#define VPFE_DCSUB_DEFAULT_VAL			0
+#define VPFE_CLAMP_DEFAULT_VAL			0
+#define VPFE_COLPTN_VAL				0xbb11bb11
+#define VPFE_TWO_BYTES_PER_PIXEL		2
+#define VPFE_INTERLACED_IMAGE_INVERT		0x4b6d
+#define VPFE_INTERLACED_NO_IMAGE_INVERT		0x0249
+#define VPFE_PROGRESSIVE_IMAGE_INVERT		0x4000
+#define VPFE_PROGRESSIVE_NO_IMAGE_INVERT	0
+#define VPFE_INTERLACED_HEIGHT_SHIFT		1
+#define VPFE_SYN_MODE_INPMOD_SHIFT		12
+#define VPFE_SYN_MODE_INPMOD_MASK		3
+#define VPFE_SYN_MODE_8BITS			(7 << 8)
+#define VPFE_SYN_MODE_10BITS			(6 << 8)
+#define VPFE_SYN_MODE_11BITS			(5 << 8)
+#define VPFE_SYN_MODE_12BITS			(4 << 8)
+#define VPFE_SYN_MODE_13BITS			(3 << 8)
+#define VPFE_SYN_MODE_14BITS			(2 << 8)
+#define VPFE_SYN_MODE_15BITS			(1 << 8)
+#define VPFE_SYN_MODE_16BITS			(0 << 8)
+#define VPFE_SYN_FLDMODE_MASK			1
+#define VPFE_SYN_FLDMODE_SHIFT			7
+#define VPFE_REC656IF_BT656_EN			3
+#define VPFE_SYN_MODE_VD_POL_NEGATIVE		BIT(2)
+#define VPFE_CCDCFG_Y8POS_SHIFT			11
+#define VPFE_CCDCFG_BW656_10BIT			BIT(5)
+#define VPFE_SDOFST_FIELD_INTERLEAVED		0x249
+#define VPFE_NO_CULLING				0xffff00ff
+#define VPFE_VDINT0				BIT(0)
+#define VPFE_VDINT1				BIT(1)
+#define VPFE_VDINT2				BIT(2)
+#define VPFE_DMA_CNTL_OVERFLOW			BIT(31)
+
+#define VPFE_CONFIG_PCLK_INV_SHIFT		0
+#define VPFE_CONFIG_PCLK_INV_MASK		1
+#define VPFE_CONFIG_PCLK_INV_NOT_INV		0
+#define VPFE_CONFIG_PCLK_INV_INV		1
+#define VPFE_CONFIG_EN_SHIFT			1
+#define VPFE_CONFIG_EN_MASK			2
+#define VPFE_CONFIG_EN_DISABLE			0
+#define VPFE_CONFIG_EN_ENABLE			1
+#define VPFE_CONFIG_ST_SHIFT			2
+#define VPFE_CONFIG_ST_MASK			4
+#define VPFE_CONFIG_ST_OCP_ACTIVE		0
+#define VPFE_CONFIG_ST_OCP_STANDBY		1
+
+#endif		/* AM437X_VPFE_REGS_H */

linux-7.2.3/drivers/media/platform/ti/cal/Makefile

@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_VIDEO_TI_CAL) += ti-cal.o
+ti-cal-y := cal.o cal-camerarx.o cal-video.o

linux-7.2.3/drivers/media/platform/ti/cal/cal.h

@@ -0,0 +1,341 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * TI Camera Access Layer (CAL)
+ *
+ * Copyright (c) 2015-2020 Texas Instruments Inc.
+ *
+ * Authors:
+ *	Benoit Parrot <bparrot@ti.com>
+ *	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ */
+#ifndef __TI_CAL_H__
+#define __TI_CAL_H__
+
+#include <linux/bitfield.h>
+#include <linux/io.h>
+#include <linux/list.h>
+#include <linux/mutex.h>
+#include <linux/spinlock.h>
+#include <linux/videodev2.h>
+#include <linux/wait.h>
+
+#include <media/media-device.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-dev.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-subdev.h>
+#include <media/videobuf2-v4l2.h>
+
+#define CAL_MODULE_NAME			"cal"
+#define CAL_MAX_NUM_CONTEXT		8
+#define CAL_NUM_CSI2_PORTS		2
+
+/*
+ * The width is limited by the size of the CAL_WR_DMA_XSIZE_j.XSIZE field,
+ * expressed in multiples of 64 bits. The height is limited by the size of the
+ * CAL_CSI2_CTXi_j.CTXi_LINES and CAL_WR_DMA_CTRL_j.YSIZE fields, expressed in
+ * lines.
+ */
+#define CAL_MIN_WIDTH_BYTES		16
+#define CAL_MAX_WIDTH_BYTES		(8192 * 8)
+#define CAL_MIN_HEIGHT_LINES		1
+#define CAL_MAX_HEIGHT_LINES		16383
+
+#define CAL_CAMERARX_PAD_SINK		0
+#define CAL_CAMERARX_PAD_FIRST_SOURCE	1
+#define CAL_CAMERARX_NUM_SOURCE_PADS	8
+#define CAL_CAMERARX_NUM_PADS		(1 + CAL_CAMERARX_NUM_SOURCE_PADS)
+
+static inline bool cal_rx_pad_is_sink(u32 pad)
+{
+	/* Camera RX has 1 sink pad, and N source pads */
+	return pad == 0;
+}
+
+static inline bool cal_rx_pad_is_source(u32 pad)
+{
+	/* Camera RX has 1 sink pad, and N source pads */
+	return pad >= CAL_CAMERARX_PAD_FIRST_SOURCE &&
+	       pad <= CAL_CAMERARX_NUM_SOURCE_PADS;
+}
+
+struct device;
+struct device_node;
+struct resource;
+struct regmap;
+struct regmap_fied;
+
+/* CTRL_CORE_CAMERRX_CONTROL register field id */
+enum cal_camerarx_field {
+	F_CTRLCLKEN,
+	F_CAMMODE,
+	F_LANEENABLE,
+	F_CSI_MODE,
+	F_MAX_FIELDS,
+};
+
+enum cal_dma_state {
+	CAL_DMA_RUNNING,
+	CAL_DMA_STOP_REQUESTED,
+	CAL_DMA_STOP_PENDING,
+	CAL_DMA_STOPPED,
+};
+
+struct cal_format_info {
+	u32	fourcc;
+	u32	code;
+	/* Bits per pixel */
+	u8	bpp;
+	bool	meta;
+};
+
+/* buffer for one video frame */
+struct cal_buffer {
+	/* common v4l buffer stuff -- must be first */
+	struct vb2_v4l2_buffer	vb;
+	struct list_head	list;
+};
+
+/**
+ * struct cal_dmaqueue - Queue of DMA buffers
+ */
+struct cal_dmaqueue {
+	/**
+	 * @lock: Protects all fields in the cal_dmaqueue.
+	 */
+	spinlock_t		lock;
+
+	/**
+	 * @queue: Buffers queued to the driver and waiting for DMA processing.
+	 * Buffers are added to the list by the vb2 .buffer_queue() operation,
+	 * and move to @pending when they are scheduled for the next frame.
+	 */
+	struct list_head	queue;
+	/**
+	 * @pending: Buffer provided to the hardware to DMA the next frame.
+	 * Will move to @active at the end of the current frame.
+	 */
+	struct cal_buffer	*pending;
+	/**
+	 * @active: Buffer being DMA'ed to for the current frame. Will be
+	 * retired and given back to vb2 at the end of the current frame if
+	 * a @pending buffer has been scheduled to replace it.
+	 */
+	struct cal_buffer	*active;
+
+	/** @state: State of the DMA engine. */
+	enum cal_dma_state	state;
+	/** @wait: Wait queue to signal a @state transition to CAL_DMA_STOPPED. */
+	struct wait_queue_head	wait;
+};
+
+struct cal_camerarx_data {
+	struct {
+		unsigned int lsb;
+		unsigned int msb;
+	} fields[F_MAX_FIELDS];
+	unsigned int num_lanes;
+};
+
+struct cal_data {
+	const struct cal_camerarx_data *camerarx;
+	unsigned int num_csi2_phy;
+	unsigned int flags;
+};
+
+/*
+ * The Camera Adaptation Layer (CAL) module is paired with one or more complex
+ * I/O PHYs (CAMERARX). It contains multiple instances of CSI-2, processing and
+ * DMA contexts.
+ *
+ * The cal_dev structure represents the whole subsystem, including the CAL and
+ * the CAMERARX instances. Instances of struct cal_dev are named cal through the
+ * driver.
+ *
+ * The cal_camerarx structure represents one CAMERARX instance. Instances of
+ * cal_camerarx are named phy through the driver.
+ *
+ * The cal_ctx structure represents the combination of one CSI-2 context, one
+ * processing context and one DMA context. Instance of struct cal_ctx are named
+ * ctx through the driver.
+ */
+
+struct cal_camerarx {
+	void __iomem		*base;
+	struct resource		*res;
+	struct regmap_field	*fields[F_MAX_FIELDS];
+
+	struct cal_dev		*cal;
+	unsigned int		instance;
+
+	struct v4l2_fwnode_endpoint	endpoint;
+	struct device_node	*source_ep_node;
+	struct device_node	*source_node;
+	struct v4l2_subdev	*source;
+	unsigned int		source_pad;
+
+	struct v4l2_subdev	subdev;
+	struct media_pad	pads[CAL_CAMERARX_NUM_PADS];
+
+	/* protects the vc_* fields below */
+	spinlock_t		vc_lock;
+	u8			vc_enable_count[4];
+	u16			vc_frame_number[4];
+	u32			vc_sequence[4];
+
+	unsigned int		enable_count;
+};
+
+struct cal_dev {
+	struct clk		*fclk;
+	int			irq;
+	void __iomem		*base;
+	struct resource		*res;
+	struct device		*dev;
+
+	const struct cal_data	*data;
+	u32			revision;
+
+	/* Control Module handle */
+	struct regmap		*syscon_camerrx;
+	u32			syscon_camerrx_offset;
+
+	/* Camera Core Module handle */
+	struct cal_camerarx	*phy[CAL_NUM_CSI2_PORTS];
+
+	u32 num_contexts;
+	struct cal_ctx		*ctx[CAL_MAX_NUM_CONTEXT];
+
+	struct media_device	mdev;
+	struct v4l2_device	v4l2_dev;
+	struct v4l2_async_notifier notifier;
+
+	unsigned long		reserved_pix_proc_mask;
+};
+
+/*
+ * There is one cal_ctx structure for each camera core context.
+ */
+struct cal_ctx {
+	struct v4l2_ctrl_handler ctrl_handler;
+	struct video_device	vdev;
+	struct media_pad	pad;
+
+	struct cal_dev		*cal;
+	struct cal_camerarx	*phy;
+
+	/* v4l2_ioctl mutex */
+	struct mutex		mutex;
+
+	struct cal_dmaqueue	dma;
+
+	/* video capture */
+	const struct cal_format_info	*fmtinfo;
+	/* Used to store current pixel format */
+	struct v4l2_format	v_fmt;
+
+	/* Current subdev enumerated format (legacy) */
+	const struct cal_format_info	**active_fmt;
+	unsigned int		num_active_fmt;
+
+	struct vb2_queue	vb_vidq;
+	u8			dma_ctx;
+	u8			cport;
+	u8			csi2_ctx;
+	u8			pix_proc;
+	u8			vc;
+	u8			datatype;
+
+	bool			use_pix_proc;
+};
+
+extern unsigned int cal_debug;
+extern int cal_video_nr;
+extern bool cal_mc_api;
+
+#define cal_dbg(level, cal, fmt, arg...)				\
+	do {								\
+		if (cal_debug >= (level))				\
+			dev_printk(KERN_DEBUG, (cal)->dev, fmt, ##arg);	\
+	} while (0)
+#define cal_info(cal, fmt, arg...)					\
+	dev_info((cal)->dev, fmt, ##arg)
+#define cal_err(cal, fmt, arg...)					\
+	dev_err((cal)->dev, fmt, ##arg)
+
+#define ctx_dbg(level, ctx, fmt, arg...)				\
+	cal_dbg(level, (ctx)->cal, "ctx%u: " fmt, (ctx)->dma_ctx, ##arg)
+#define ctx_info(ctx, fmt, arg...)					\
+	cal_info((ctx)->cal, "ctx%u: " fmt, (ctx)->dma_ctx, ##arg)
+#define ctx_err(ctx, fmt, arg...)					\
+	cal_err((ctx)->cal, "ctx%u: " fmt, (ctx)->dma_ctx, ##arg)
+
+#define phy_dbg(level, phy, fmt, arg...)				\
+	cal_dbg(level, (phy)->cal, "phy%u: " fmt, (phy)->instance, ##arg)
+#define phy_info(phy, fmt, arg...)					\
+	cal_info((phy)->cal, "phy%u: " fmt, (phy)->instance, ##arg)
+#define phy_err(phy, fmt, arg...)					\
+	cal_err((phy)->cal, "phy%u: " fmt, (phy)->instance, ##arg)
+
+static inline u32 cal_read(struct cal_dev *cal, u32 offset)
+{
+	return ioread32(cal->base + offset);
+}
+
+static inline void cal_write(struct cal_dev *cal, u32 offset, u32 val)
+{
+	iowrite32(val, cal->base + offset);
+}
+
+static __always_inline u32 cal_read_field(struct cal_dev *cal, u32 offset, u32 mask)
+{
+	return FIELD_GET(mask, cal_read(cal, offset));
+}
+
+static inline void cal_write_field(struct cal_dev *cal, u32 offset, u32 value,
+				   u32 mask)
+{
+	u32 val = cal_read(cal, offset);
+
+	val &= ~mask;
+	val |= (value << __ffs(mask)) & mask;
+	cal_write(cal, offset, val);
+}
+
+static inline void cal_set_field(u32 *valp, u32 field, u32 mask)
+{
+	u32 val = *valp;
+
+	val &= ~mask;
+	val |= (field << __ffs(mask)) & mask;
+	*valp = val;
+}
+
+extern const struct cal_format_info cal_formats[];
+extern const unsigned int cal_num_formats;
+const struct cal_format_info *cal_format_by_fourcc(u32 fourcc);
+const struct cal_format_info *cal_format_by_code(u32 code);
+
+void cal_quickdump_regs(struct cal_dev *cal);
+
+struct cal_camerarx *cal_camerarx_get_phy_from_entity(struct media_entity *entity);
+void cal_camerarx_disable(struct cal_camerarx *phy);
+void cal_camerarx_i913_errata(struct cal_camerarx *phy);
+struct cal_camerarx *cal_camerarx_create(struct cal_dev *cal,
+					 unsigned int instance);
+void cal_camerarx_destroy(struct cal_camerarx *phy);
+
+int cal_ctx_prepare(struct cal_ctx *ctx);
+void cal_ctx_unprepare(struct cal_ctx *ctx);
+void cal_ctx_set_dma_addr(struct cal_ctx *ctx, dma_addr_t addr);
+void cal_ctx_start(struct cal_ctx *ctx);
+void cal_ctx_stop(struct cal_ctx *ctx);
+
+int cal_ctx_v4l2_register(struct cal_ctx *ctx);
+void cal_ctx_v4l2_unregister(struct cal_ctx *ctx);
+int cal_ctx_v4l2_init(struct cal_ctx *ctx);
+void cal_ctx_v4l2_cleanup(struct cal_ctx *ctx);
+
+#endif /* __TI_CAL_H__ */

linux-7.2.3/drivers/media/platform/ti/cal/cal_regs.h

@@ -0,0 +1,463 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * TI CAL camera interface driver
+ *
+ * Copyright (c) 2015 Texas Instruments Inc.
+ *
+ * Benoit Parrot, <bparrot@ti.com>
+ */
+
+#ifndef __TI_CAL_REGS_H
+#define __TI_CAL_REGS_H
+
+/*
+ * struct cal_dev.flags possibilities
+ *
+ * DRA72_CAL_PRE_ES2_LDO_DISABLE:
+ *   Errata i913: CSI2 LDO Needs to be disabled when module is powered on
+ *
+ *   Enabling CSI2 LDO shorts it to core supply. It is crucial the 2 CSI2
+ *   LDOs on the device are disabled if CSI-2 module is powered on
+ *   (0x4845 B304 | 0x4845 B384 [28:27] = 0x1) or in ULPS (0x4845 B304
+ *   | 0x4845 B384 [28:27] = 0x2) mode. Common concerns include: high
+ *   current draw on the module supply in active mode.
+ *
+ *   Errata does not apply when CSI-2 module is powered off
+ *   (0x4845 B304 | 0x4845 B384 [28:27] = 0x0).
+ *
+ * SW Workaround:
+ *	Set the following register bits to disable the LDO,
+ *	which is essentially CSI2 REG10 bit 6:
+ *
+ *		Core 0:  0x4845 B828 = 0x0000 0040
+ *		Core 1:  0x4845 B928 = 0x0000 0040
+ */
+#define DRA72_CAL_PRE_ES2_LDO_DISABLE BIT(0)
+
+/* CAL register offsets */
+
+#define CAL_HL_REVISION			0x0000
+#define CAL_HL_HWINFO			0x0004
+#define CAL_HL_SYSCONFIG		0x0010
+#define CAL_HL_IRQ_EOI			0x001c
+#define CAL_HL_IRQSTATUS_RAW(m)		(0x20U + (m) * 0x10U)
+#define CAL_HL_IRQSTATUS(m)		(0x24U + (m) * 0x10U)
+#define CAL_HL_IRQENABLE_SET(m)		(0x28U + (m) * 0x10U)
+#define CAL_HL_IRQENABLE_CLR(m)		(0x2cU + (m) * 0x10U)
+#define CAL_PIX_PROC(m)			(0xc0U + (m) * 0x4U)
+#define CAL_CTRL			0x100
+#define CAL_CTRL1			0x104
+#define CAL_LINE_NUMBER_EVT		0x108
+#define CAL_VPORT_CTRL1			0x120
+#define CAL_VPORT_CTRL2			0x124
+#define CAL_BYS_CTRL1			0x130
+#define CAL_BYS_CTRL2			0x134
+#define CAL_RD_DMA_CTRL			0x140
+#define CAL_RD_DMA_PIX_ADDR		0x144
+#define CAL_RD_DMA_PIX_OFST		0x148
+#define CAL_RD_DMA_XSIZE		0x14c
+#define CAL_RD_DMA_YSIZE		0x150
+#define CAL_RD_DMA_INIT_ADDR		0x154
+#define CAL_RD_DMA_INIT_OFST		0x168
+#define CAL_RD_DMA_CTRL2		0x16c
+#define CAL_WR_DMA_CTRL(m)		(0x200U + (m) * 0x10U)
+#define CAL_WR_DMA_ADDR(m)		(0x204U + (m) * 0x10U)
+#define CAL_WR_DMA_OFST(m)		(0x208U + (m) * 0x10U)
+#define CAL_WR_DMA_XSIZE(m)		(0x20cU + (m) * 0x10U)
+#define CAL_CSI2_PPI_CTRL(m)		(0x300U + (m) * 0x80U)
+#define CAL_CSI2_COMPLEXIO_CFG(m)	(0x304U + (m) * 0x80U)
+#define CAL_CSI2_COMPLEXIO_IRQSTATUS(m)	(0x308U + (m) * 0x80U)
+#define CAL_CSI2_SHORT_PACKET(m)	(0x30cU + (m) * 0x80U)
+#define CAL_CSI2_COMPLEXIO_IRQENABLE(m)	(0x310U + (m) * 0x80U)
+#define CAL_CSI2_TIMING(m)		(0x314U + (m) * 0x80U)
+#define CAL_CSI2_VC_IRQENABLE(m)	(0x318U + (m) * 0x80U)
+#define CAL_CSI2_VC_IRQSTATUS(m)	(0x328U + (m) * 0x80U)
+#define CAL_CSI2_CTX(phy, csi2_ctx)	(0x330U + (phy) * 0x80U + (csi2_ctx) * 4)
+#define CAL_CSI2_STATUS(phy, csi2_ctx)	(0x350U + (phy) * 0x80U + (csi2_ctx) * 4)
+
+/* CAL CSI2 PHY register offsets */
+#define CAL_CSI2_PHY_REG0		0x000
+#define CAL_CSI2_PHY_REG1		0x004
+#define CAL_CSI2_PHY_REG2		0x008
+#define CAL_CSI2_PHY_REG10		0x028
+
+/* CAL Control Module Core Camerrx Control register offsets */
+#define CM_CTRL_CORE_CAMERRX_CONTROL	0x000
+
+/*********************************************************************
+* Field Definition Macros
+*********************************************************************/
+
+#define CAL_HL_REVISION_MINOR_MASK		GENMASK(5, 0)
+#define CAL_HL_REVISION_CUSTOM_MASK		GENMASK(7, 6)
+#define CAL_HL_REVISION_MAJOR_MASK		GENMASK(10, 8)
+#define CAL_HL_REVISION_RTL_MASK		GENMASK(15, 11)
+#define CAL_HL_REVISION_FUNC_MASK		GENMASK(27, 16)
+#define CAL_HL_REVISION_SCHEME_MASK		GENMASK(31, 30)
+#define CAL_HL_REVISION_SCHEME_H08			1
+#define CAL_HL_REVISION_SCHEME_LEGACY			0
+
+#define CAL_HL_HWINFO_WFIFO_MASK		GENMASK(3, 0)
+#define CAL_HL_HWINFO_RFIFO_MASK		GENMASK(7, 4)
+#define CAL_HL_HWINFO_PCTX_MASK			GENMASK(12, 8)
+#define CAL_HL_HWINFO_WCTX_MASK			GENMASK(18, 13)
+#define CAL_HL_HWINFO_VFIFO_MASK		GENMASK(22, 19)
+#define CAL_HL_HWINFO_NCPORT_MASK		GENMASK(27, 23)
+#define CAL_HL_HWINFO_NPPI_CTXS0_MASK		GENMASK(29, 28)
+#define CAL_HL_HWINFO_NPPI_CTXS1_MASK		GENMASK(31, 30)
+#define CAL_HL_HWINFO_NPPI_CONTEXTS_ZERO		0
+#define CAL_HL_HWINFO_NPPI_CONTEXTS_FOUR		1
+#define CAL_HL_HWINFO_NPPI_CONTEXTS_EIGHT		2
+#define CAL_HL_HWINFO_NPPI_CONTEXTS_RESERVED		3
+
+#define CAL_HL_SYSCONFIG_SOFTRESET_MASK		BIT(0)
+#define CAL_HL_SYSCONFIG_SOFTRESET_DONE			0x0
+#define CAL_HL_SYSCONFIG_SOFTRESET_PENDING		0x1
+#define CAL_HL_SYSCONFIG_SOFTRESET_NOACTION		0x0
+#define CAL_HL_SYSCONFIG_SOFTRESET_RESET		0x1
+#define CAL_HL_SYSCONFIG_IDLE_MASK		GENMASK(3, 2)
+#define CAL_HL_SYSCONFIG_IDLEMODE_FORCE			0
+#define CAL_HL_SYSCONFIG_IDLEMODE_NO			1
+#define CAL_HL_SYSCONFIG_IDLEMODE_SMART1		2
+#define CAL_HL_SYSCONFIG_IDLEMODE_SMART2		3
+
+#define CAL_HL_IRQ_EOI_LINE_NUMBER_MASK		BIT(0)
+#define CAL_HL_IRQ_EOI_LINE_NUMBER_READ0		0
+#define CAL_HL_IRQ_EOI_LINE_NUMBER_EOI0			0
+
+#define CAL_HL_IRQ_WDMA_END_MASK(m)		BIT(m)
+#define CAL_HL_IRQ_WDMA_START_MASK(m)		BIT(m)
+
+#define CAL_HL_IRQ_OCPO_ERR_MASK		BIT(6)
+
+#define CAL_HL_IRQ_CIO_MASK(i)			BIT(16 + (i) * 8)
+#define CAL_HL_IRQ_VC_MASK(i)			BIT(17 + (i) * 8)
+
+#define CAL_PIX_PROC_EN_MASK			BIT(0)
+#define CAL_PIX_PROC_EXTRACT_MASK		GENMASK(4, 1)
+#define CAL_PIX_PROC_EXTRACT_B6				0x0
+#define CAL_PIX_PROC_EXTRACT_B7				0x1
+#define CAL_PIX_PROC_EXTRACT_B8				0x2
+#define CAL_PIX_PROC_EXTRACT_B10			0x3
+#define CAL_PIX_PROC_EXTRACT_B10_MIPI			0x4
+#define CAL_PIX_PROC_EXTRACT_B12			0x5
+#define CAL_PIX_PROC_EXTRACT_B12_MIPI			0x6
+#define CAL_PIX_PROC_EXTRACT_B14			0x7
+#define CAL_PIX_PROC_EXTRACT_B14_MIPI			0x8
+#define CAL_PIX_PROC_EXTRACT_B16_BE			0x9
+#define CAL_PIX_PROC_EXTRACT_B16_LE			0xa
+#define CAL_PIX_PROC_DPCMD_MASK			GENMASK(9, 5)
+#define CAL_PIX_PROC_DPCMD_BYPASS			0x0
+#define CAL_PIX_PROC_DPCMD_DPCM_10_8_1			0x2
+#define CAL_PIX_PROC_DPCMD_DPCM_12_8_1			0x8
+#define CAL_PIX_PROC_DPCMD_DPCM_10_7_1			0x4
+#define CAL_PIX_PROC_DPCMD_DPCM_10_7_2			0x5
+#define CAL_PIX_PROC_DPCMD_DPCM_10_6_1			0x6
+#define CAL_PIX_PROC_DPCMD_DPCM_10_6_2			0x7
+#define CAL_PIX_PROC_DPCMD_DPCM_12_7_1			0xa
+#define CAL_PIX_PROC_DPCMD_DPCM_12_6_1			0xc
+#define CAL_PIX_PROC_DPCMD_DPCM_14_10			0xe
+#define CAL_PIX_PROC_DPCMD_DPCM_14_8_1			0x10
+#define CAL_PIX_PROC_DPCMD_DPCM_16_12_1			0x12
+#define CAL_PIX_PROC_DPCMD_DPCM_16_10_1			0x14
+#define CAL_PIX_PROC_DPCMD_DPCM_16_8_1			0x16
+#define CAL_PIX_PROC_DPCME_MASK			GENMASK(15, 11)
+#define CAL_PIX_PROC_DPCME_BYPASS			0x0
+#define CAL_PIX_PROC_DPCME_DPCM_10_8_1			0x2
+#define CAL_PIX_PROC_DPCME_DPCM_12_8_1			0x8
+#define CAL_PIX_PROC_DPCME_DPCM_14_10			0xe
+#define CAL_PIX_PROC_DPCME_DPCM_14_8_1			0x10
+#define CAL_PIX_PROC_DPCME_DPCM_16_12_1			0x12
+#define CAL_PIX_PROC_DPCME_DPCM_16_10_1			0x14
+#define CAL_PIX_PROC_DPCME_DPCM_16_8_1			0x16
+#define CAL_PIX_PROC_PACK_MASK			GENMASK(18, 16)
+#define CAL_PIX_PROC_PACK_B8				0x0
+#define CAL_PIX_PROC_PACK_B10_MIPI			0x2
+#define CAL_PIX_PROC_PACK_B12				0x3
+#define CAL_PIX_PROC_PACK_B12_MIPI			0x4
+#define CAL_PIX_PROC_PACK_B16				0x5
+#define CAL_PIX_PROC_PACK_ARGB				0x6
+#define CAL_PIX_PROC_CPORT_MASK			GENMASK(23, 19)
+
+#define CAL_CTRL_POSTED_WRITES_MASK		BIT(0)
+#define CAL_CTRL_POSTED_WRITES_NONPOSTED		0
+#define CAL_CTRL_POSTED_WRITES				1
+#define CAL_CTRL_TAGCNT_MASK			GENMASK(4, 1)
+#define CAL_CTRL_BURSTSIZE_MASK			GENMASK(6, 5)
+#define CAL_CTRL_BURSTSIZE_BURST16			0x0
+#define CAL_CTRL_BURSTSIZE_BURST32			0x1
+#define CAL_CTRL_BURSTSIZE_BURST64			0x2
+#define CAL_CTRL_BURSTSIZE_BURST128			0x3
+#define CAL_CTRL_LL_FORCE_STATE_MASK		GENMASK(12, 7)
+#define CAL_CTRL_MFLAGL_MASK			GENMASK(20, 13)
+#define CAL_CTRL_PWRSCPCLK_MASK			BIT(21)
+#define CAL_CTRL_PWRSCPCLK_AUTO				0
+#define CAL_CTRL_PWRSCPCLK_FORCE			1
+#define CAL_CTRL_RD_DMA_STALL_MASK		BIT(22)
+#define CAL_CTRL_MFLAGH_MASK			GENMASK(31, 24)
+
+#define CAL_CTRL1_PPI_GROUPING_MASK		GENMASK(1, 0)
+#define CAL_CTRL1_PPI_GROUPING_DISABLED			0
+#define CAL_CTRL1_PPI_GROUPING_RESERVED			1
+#define CAL_CTRL1_PPI_GROUPING_0			2
+#define CAL_CTRL1_PPI_GROUPING_1			3
+#define CAL_CTRL1_INTERLEAVE01_MASK		GENMASK(3, 2)
+#define CAL_CTRL1_INTERLEAVE01_DISABLED			0
+#define CAL_CTRL1_INTERLEAVE01_PIX1			1
+#define CAL_CTRL1_INTERLEAVE01_PIX4			2
+#define CAL_CTRL1_INTERLEAVE01_RESERVED			3
+#define CAL_CTRL1_INTERLEAVE23_MASK		GENMASK(5, 4)
+#define CAL_CTRL1_INTERLEAVE23_DISABLED			0
+#define CAL_CTRL1_INTERLEAVE23_PIX1			1
+#define CAL_CTRL1_INTERLEAVE23_PIX4			2
+#define CAL_CTRL1_INTERLEAVE23_RESERVED			3
+
+#define CAL_LINE_NUMBER_EVT_CPORT_MASK		GENMASK(4, 0)
+#define CAL_LINE_NUMBER_EVT_MASK		GENMASK(29, 16)
+
+#define CAL_VPORT_CTRL1_PCLK_MASK		GENMASK(16, 0)
+#define CAL_VPORT_CTRL1_XBLK_MASK		GENMASK(24, 17)
+#define CAL_VPORT_CTRL1_YBLK_MASK		GENMASK(30, 25)
+#define CAL_VPORT_CTRL1_WIDTH_MASK		BIT(31)
+#define CAL_VPORT_CTRL1_WIDTH_ONE			0
+#define CAL_VPORT_CTRL1_WIDTH_TWO			1
+
+#define CAL_VPORT_CTRL2_CPORT_MASK		GENMASK(4, 0)
+#define CAL_VPORT_CTRL2_FREERUNNING_MASK	BIT(15)
+#define CAL_VPORT_CTRL2_FREERUNNING_GATED		0
+#define CAL_VPORT_CTRL2_FREERUNNING_FREE		1
+#define CAL_VPORT_CTRL2_FS_RESETS_MASK		BIT(16)
+#define CAL_VPORT_CTRL2_FS_RESETS_NO			0
+#define CAL_VPORT_CTRL2_FS_RESETS_YES			1
+#define CAL_VPORT_CTRL2_FSM_RESET_MASK		BIT(17)
+#define CAL_VPORT_CTRL2_FSM_RESET_NOEFFECT		0
+#define CAL_VPORT_CTRL2_FSM_RESET			1
+#define CAL_VPORT_CTRL2_RDY_THR_MASK		GENMASK(31, 18)
+
+#define CAL_BYS_CTRL1_PCLK_MASK			GENMASK(16, 0)
+#define CAL_BYS_CTRL1_XBLK_MASK			GENMASK(24, 17)
+#define CAL_BYS_CTRL1_YBLK_MASK			GENMASK(30, 25)
+#define CAL_BYS_CTRL1_BYSINEN_MASK		BIT(31)
+
+#define CAL_BYS_CTRL2_CPORTIN_MASK		GENMASK(4, 0)
+#define CAL_BYS_CTRL2_CPORTOUT_MASK		GENMASK(9, 5)
+#define CAL_BYS_CTRL2_DUPLICATEDDATA_MASK	BIT(10)
+#define CAL_BYS_CTRL2_DUPLICATEDDATA_NO			0
+#define CAL_BYS_CTRL2_DUPLICATEDDATA_YES		1
+#define CAL_BYS_CTRL2_FREERUNNING_MASK		BIT(11)
+#define CAL_BYS_CTRL2_FREERUNNING_NO			0
+#define CAL_BYS_CTRL2_FREERUNNING_YES			1
+
+#define CAL_RD_DMA_CTRL_GO_MASK			BIT(0)
+#define CAL_RD_DMA_CTRL_GO_DIS				0
+#define CAL_RD_DMA_CTRL_GO_EN				1
+#define CAL_RD_DMA_CTRL_GO_IDLE				0
+#define CAL_RD_DMA_CTRL_GO_BUSY				1
+#define CAL_RD_DMA_CTRL_INIT_MASK		BIT(1)
+#define CAL_RD_DMA_CTRL_BW_LIMITER_MASK		GENMASK(10, 2)
+#define CAL_RD_DMA_CTRL_OCP_TAG_CNT_MASK	GENMASK(14, 11)
+#define CAL_RD_DMA_CTRL_PCLK_MASK		GENMASK(31, 15)
+
+#define CAL_RD_DMA_PIX_ADDR_MASK		GENMASK(31, 3)
+
+#define CAL_RD_DMA_PIX_OFST_MASK		GENMASK(31, 4)
+
+#define CAL_RD_DMA_XSIZE_MASK			GENMASK(31, 19)
+
+#define CAL_RD_DMA_YSIZE_MASK			GENMASK(29, 16)
+
+#define CAL_RD_DMA_INIT_ADDR_MASK		GENMASK(31, 3)
+
+#define CAL_RD_DMA_INIT_OFST_MASK		GENMASK(31, 3)
+
+#define CAL_RD_DMA_CTRL2_CIRC_MODE_MASK		GENMASK(2, 0)
+#define CAL_RD_DMA_CTRL2_CIRC_MODE_DIS			0
+#define CAL_RD_DMA_CTRL2_CIRC_MODE_ONE			1
+#define CAL_RD_DMA_CTRL2_CIRC_MODE_FOUR			2
+#define CAL_RD_DMA_CTRL2_CIRC_MODE_SIXTEEN		3
+#define CAL_RD_DMA_CTRL2_CIRC_MODE_SIXTYFOUR		4
+#define CAL_RD_DMA_CTRL2_CIRC_MODE_RESERVED		5
+#define CAL_RD_DMA_CTRL2_ICM_CSTART_MASK	BIT(3)
+#define CAL_RD_DMA_CTRL2_PATTERN_MASK		GENMASK(5, 4)
+#define CAL_RD_DMA_CTRL2_PATTERN_LINEAR			0
+#define CAL_RD_DMA_CTRL2_PATTERN_YUV420			1
+#define CAL_RD_DMA_CTRL2_PATTERN_RD2SKIP2		2
+#define CAL_RD_DMA_CTRL2_PATTERN_RD2SKIP4		3
+#define CAL_RD_DMA_CTRL2_BYSOUT_LE_WAIT_MASK	BIT(6)
+#define CAL_RD_DMA_CTRL2_BYSOUT_LE_WAIT_FREERUNNING	0
+#define CAL_RD_DMA_CTRL2_BYSOUT_LE_WAIT_WAITFORBYSOUT	1
+#define CAL_RD_DMA_CTRL2_CIRC_SIZE_MASK		GENMASK(29, 16)
+
+#define CAL_WR_DMA_CTRL_MODE_MASK		GENMASK(2, 0)
+#define CAL_WR_DMA_CTRL_MODE_DIS			0
+#define CAL_WR_DMA_CTRL_MODE_SHD			1
+#define CAL_WR_DMA_CTRL_MODE_CNT			2
+#define CAL_WR_DMA_CTRL_MODE_CNT_INIT			3
+#define CAL_WR_DMA_CTRL_MODE_CONST			4
+#define CAL_WR_DMA_CTRL_MODE_RESERVED			5
+#define CAL_WR_DMA_CTRL_PATTERN_MASK		GENMASK(4, 3)
+#define CAL_WR_DMA_CTRL_PATTERN_LINEAR			0
+#define CAL_WR_DMA_CTRL_PATTERN_WR2SKIP2		2
+#define CAL_WR_DMA_CTRL_PATTERN_WR2SKIP4		3
+#define CAL_WR_DMA_CTRL_PATTERN_RESERVED		1
+#define CAL_WR_DMA_CTRL_ICM_PSTART_MASK		BIT(5)
+#define CAL_WR_DMA_CTRL_DTAG_MASK		GENMASK(8, 6)
+#define CAL_WR_DMA_CTRL_DTAG_ATT_HDR			0
+#define CAL_WR_DMA_CTRL_DTAG_ATT_DAT			1
+#define CAL_WR_DMA_CTRL_DTAG				2
+#define CAL_WR_DMA_CTRL_DTAG_PIX_HDR			3
+#define CAL_WR_DMA_CTRL_DTAG_PIX_DAT			4
+#define CAL_WR_DMA_CTRL_DTAG_D5				5
+#define CAL_WR_DMA_CTRL_DTAG_D6				6
+#define CAL_WR_DMA_CTRL_DTAG_D7				7
+#define CAL_WR_DMA_CTRL_CPORT_MASK		GENMASK(13, 9)
+#define CAL_WR_DMA_CTRL_STALL_RD_MASK		BIT(14)
+#define CAL_WR_DMA_CTRL_YSIZE_MASK		GENMASK(31, 18)
+
+#define CAL_WR_DMA_ADDR_MASK			GENMASK(31, 4)
+
+#define CAL_WR_DMA_OFST_MASK			GENMASK(18, 4)
+#define CAL_WR_DMA_OFST_CIRC_MODE_MASK		GENMASK(23, 22)
+#define CAL_WR_DMA_OFST_CIRC_MODE_ONE			1
+#define CAL_WR_DMA_OFST_CIRC_MODE_FOUR			2
+#define CAL_WR_DMA_OFST_CIRC_MODE_SIXTYFOUR		3
+#define CAL_WR_DMA_OFST_CIRC_MODE_DISABLED		0
+#define CAL_WR_DMA_OFST_CIRC_SIZE_MASK		GENMASK(31, 24)
+
+#define CAL_WR_DMA_XSIZE_XSKIP_MASK		GENMASK(15, 3)
+#define CAL_WR_DMA_XSIZE_MASK			GENMASK(31, 19)
+
+#define CAL_CSI2_PPI_CTRL_IF_EN_MASK		BIT(0)
+#define CAL_CSI2_PPI_CTRL_ECC_EN_MASK		BIT(2)
+#define CAL_CSI2_PPI_CTRL_FRAME_MASK		BIT(3)
+#define CAL_CSI2_PPI_CTRL_FRAME_IMMEDIATE		0
+#define CAL_CSI2_PPI_CTRL_FRAME				1
+
+#define CAL_CSI2_COMPLEXIO_CFG_CLOCK_POSITION_MASK	GENMASK(2, 0)
+#define CAL_CSI2_COMPLEXIO_CFG_POSITION_5			5
+#define CAL_CSI2_COMPLEXIO_CFG_POSITION_4			4
+#define CAL_CSI2_COMPLEXIO_CFG_POSITION_3			3
+#define CAL_CSI2_COMPLEXIO_CFG_POSITION_2			2
+#define CAL_CSI2_COMPLEXIO_CFG_POSITION_1			1
+#define CAL_CSI2_COMPLEXIO_CFG_POSITION_NOT_USED		0
+#define CAL_CSI2_COMPLEXIO_CFG_CLOCK_POL_MASK		BIT(3)
+#define CAL_CSI2_COMPLEXIO_CFG_POL_PLUSMINUS			0
+#define CAL_CSI2_COMPLEXIO_CFG_POL_MINUSPLUS			1
+#define CAL_CSI2_COMPLEXIO_CFG_DATA1_POSITION_MASK	GENMASK(6, 4)
+#define CAL_CSI2_COMPLEXIO_CFG_DATA1_POL_MASK		BIT(7)
+#define CAL_CSI2_COMPLEXIO_CFG_DATA2_POSITION_MASK	GENMASK(10, 8)
+#define CAL_CSI2_COMPLEXIO_CFG_DATA2_POL_MASK		BIT(11)
+#define CAL_CSI2_COMPLEXIO_CFG_DATA3_POSITION_MASK	GENMASK(14, 12)
+#define CAL_CSI2_COMPLEXIO_CFG_DATA3_POL_MASK		BIT(15)
+#define CAL_CSI2_COMPLEXIO_CFG_DATA4_POSITION_MASK	GENMASK(18, 16)
+#define CAL_CSI2_COMPLEXIO_CFG_DATA4_POL_MASK		BIT(19)
+#define CAL_CSI2_COMPLEXIO_CFG_PWR_AUTO_MASK		BIT(24)
+#define CAL_CSI2_COMPLEXIO_CFG_PWR_STATUS_MASK		GENMASK(26, 25)
+#define CAL_CSI2_COMPLEXIO_CFG_PWR_STATUS_STATE_OFF		0
+#define CAL_CSI2_COMPLEXIO_CFG_PWR_STATUS_STATE_ON		1
+#define CAL_CSI2_COMPLEXIO_CFG_PWR_STATUS_STATE_ULP		2
+#define CAL_CSI2_COMPLEXIO_CFG_PWR_CMD_MASK		GENMASK(28, 27)
+#define CAL_CSI2_COMPLEXIO_CFG_PWR_CMD_STATE_OFF		0
+#define CAL_CSI2_COMPLEXIO_CFG_PWR_CMD_STATE_ON			1
+#define CAL_CSI2_COMPLEXIO_CFG_PWR_CMD_STATE_ULP		2
+#define CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_MASK		BIT(29)
+#define CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_RESETCOMPLETED	1
+#define CAL_CSI2_COMPLEXIO_CFG_RESET_DONE_RESETONGOING		0
+#define CAL_CSI2_COMPLEXIO_CFG_RESET_CTRL_MASK		BIT(30)
+#define CAL_CSI2_COMPLEXIO_CFG_RESET_CTRL			0
+#define CAL_CSI2_COMPLEXIO_CFG_RESET_CTRL_OPERATIONAL		1
+
+#define CAL_CSI2_SHORT_PACKET_MASK	GENMASK(23, 0)
+
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRSOTHS1_MASK		BIT(0)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRSOTHS2_MASK		BIT(1)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRSOTHS3_MASK		BIT(2)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRSOTHS4_MASK		BIT(3)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRSOTHS5_MASK		BIT(4)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRSOTSYNCHS1_MASK	BIT(5)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRSOTSYNCHS2_MASK	BIT(6)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRSOTSYNCHS3_MASK	BIT(7)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRSOTSYNCHS4_MASK	BIT(8)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRSOTSYNCHS5_MASK	BIT(9)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRESC1_MASK		BIT(10)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRESC2_MASK		BIT(11)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRESC3_MASK		BIT(12)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRESC4_MASK		BIT(13)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRESC5_MASK		BIT(14)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRCONTROL1_MASK		BIT(15)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRCONTROL2_MASK		BIT(16)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRCONTROL3_MASK		BIT(17)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRCONTROL4_MASK		BIT(18)
+#define CAL_CSI2_COMPLEXIO_IRQ_ERRCONTROL5_MASK		BIT(19)
+#define CAL_CSI2_COMPLEXIO_IRQ_LANE_ERRORS_MASK		GENMASK(19, 0)
+#define CAL_CSI2_COMPLEXIO_IRQ_STATEULPM1_MASK		BIT(20)
+#define CAL_CSI2_COMPLEXIO_IRQ_STATEULPM2_MASK		BIT(21)
+#define CAL_CSI2_COMPLEXIO_IRQ_STATEULPM3_MASK		BIT(22)
+#define CAL_CSI2_COMPLEXIO_IRQ_STATEULPM4_MASK		BIT(23)
+#define CAL_CSI2_COMPLEXIO_IRQ_STATEULPM5_MASK		BIT(24)
+#define CAL_CSI2_COMPLEXIO_IRQ_STATEALLULPMENTER_MASK	BIT(25)
+#define CAL_CSI2_COMPLEXIO_IRQ_STATEALLULPMEXIT_MASK	BIT(26)
+#define CAL_CSI2_COMPLEXIO_IRQ_FIFO_OVR_MASK		BIT(27)
+#define CAL_CSI2_COMPLEXIO_IRQ_SHORT_PACKET_MASK	BIT(28)
+#define CAL_CSI2_COMPLEXIO_IRQ_ECC_NO_CORRECTION_MASK	BIT(30)
+
+#define CAL_CSI2_TIMING_STOP_STATE_COUNTER_IO1_MASK	GENMASK(12, 0)
+#define CAL_CSI2_TIMING_STOP_STATE_X4_IO1_MASK		BIT(13)
+#define CAL_CSI2_TIMING_STOP_STATE_X16_IO1_MASK		BIT(14)
+#define CAL_CSI2_TIMING_FORCE_RX_MODE_IO1_MASK		BIT(15)
+
+#define CAL_CSI2_VC_IRQ_FS_IRQ_MASK(n)			BIT(0 + ((n) * 8))
+#define CAL_CSI2_VC_IRQ_FE_IRQ_MASK(n)			BIT(1 + ((n) * 8))
+#define CAL_CSI2_VC_IRQ_LS_IRQ_MASK(n)			BIT(2 + ((n) * 8))
+#define CAL_CSI2_VC_IRQ_LE_IRQ_MASK(n)			BIT(3 + ((n) * 8))
+#define CAL_CSI2_VC_IRQ_CS_IRQ_MASK(n)			BIT(4 + ((n) * 8))
+#define CAL_CSI2_VC_IRQ_ECC_CORRECTION_IRQ_MASK(n)	BIT(5 + ((n) * 8))
+
+#define CAL_CSI2_CTX_DT_MASK		GENMASK(5, 0)
+#define CAL_CSI2_CTX_DT_DISABLED	0
+#define CAL_CSI2_CTX_DT_ANY		1
+#define CAL_CSI2_CTX_VC_MASK		GENMASK(7, 6)
+#define CAL_CSI2_CTX_CPORT_MASK		GENMASK(12, 8)
+#define CAL_CSI2_CTX_ATT_MASK		BIT(13)
+#define CAL_CSI2_CTX_ATT_PIX			0
+#define CAL_CSI2_CTX_ATT			1
+#define CAL_CSI2_CTX_PACK_MODE_MASK	BIT(14)
+#define CAL_CSI2_CTX_PACK_MODE_LINE		0
+#define CAL_CSI2_CTX_PACK_MODE_FRAME		1
+#define CAL_CSI2_CTX_LINES_MASK		GENMASK(29, 16)
+
+#define CAL_CSI2_STATUS_FRAME_MASK	GENMASK(15, 0)
+
+#define CAL_CSI2_PHY_REG0_THS_SETTLE_MASK	GENMASK(7, 0)
+#define CAL_CSI2_PHY_REG0_THS_TERM_MASK		GENMASK(15, 8)
+#define CAL_CSI2_PHY_REG0_HSCLOCKCONFIG_MASK	BIT(24)
+#define CAL_CSI2_PHY_REG0_HSCLOCKCONFIG_DISABLE		1
+#define CAL_CSI2_PHY_REG0_HSCLOCKCONFIG_ENABLE		0
+
+#define CAL_CSI2_PHY_REG1_TCLK_SETTLE_MASK			GENMASK(7, 0)
+#define CAL_CSI2_PHY_REG1_CTRLCLK_DIV_FACTOR_MASK		GENMASK(9, 8)
+#define CAL_CSI2_PHY_REG1_DPHY_HS_SYNC_PATTERN_MASK		GENMASK(17, 10)
+#define CAL_CSI2_PHY_REG1_TCLK_TERM_MASK			GENMASK(24, 18)
+#define CAL_CSI2_PHY_REG1_CLOCK_MISS_DETECTOR_STATUS_MASK	BIT(25)
+#define CAL_CSI2_PHY_REG1_CLOCK_MISS_DETECTOR_STATUS_ERROR		1
+#define CAL_CSI2_PHY_REG1_CLOCK_MISS_DETECTOR_STATUS_SUCCESS		0
+#define CAL_CSI2_PHY_REG1_RESET_DONE_STATUS_MASK		GENMASK(29, 28)
+
+#define CAL_CSI2_PHY_REG10_I933_LDO_DISABLE_MASK		BIT(6)
+
+#define CAL_CSI2_PHY_REG2_CCP2_SYNC_PATTERN_MASK		GENMASK(23, 0)
+#define CAL_CSI2_PHY_REG2_TRIGGER_CMD_RXTRIGESC3_MASK		GENMASK(25, 24)
+#define CAL_CSI2_PHY_REG2_TRIGGER_CMD_RXTRIGESC2_MASK		GENMASK(27, 26)
+#define CAL_CSI2_PHY_REG2_TRIGGER_CMD_RXTRIGESC1_MASK		GENMASK(29, 28)
+#define CAL_CSI2_PHY_REG2_TRIGGER_CMD_RXTRIGESC0_MASK		GENMASK(31, 30)
+
+#define CM_CAMERRX_CTRL_CSI1_CTRLCLKEN_MASK			BIT(0)
+#define CM_CAMERRX_CTRL_CSI1_CAMMODE_MASK			GENMASK(2, 1)
+#define CM_CAMERRX_CTRL_CSI1_LANEENABLE_MASK			GENMASK(4, 3)
+#define CM_CAMERRX_CTRL_CSI1_MODE_MASK				BIT(5)
+#define CM_CAMERRX_CTRL_CSI0_CTRLCLKEN_MASK			BIT(10)
+#define CM_CAMERRX_CTRL_CSI0_CAMMODE_MASK			GENMASK(12, 11)
+#define CM_CAMERRX_CTRL_CSI0_LANEENABLE_MASK			GENMASK(16, 13)
+#define CM_CAMERRX_CTRL_CSI0_MODE_MASK				BIT(17)
+
+#endif

linux-7.2.3/drivers/media/platform/ti/davinci/Kconfig

@@ -0,0 +1,33 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config VIDEO_DAVINCI_VPIF_DISPLAY
+	tristate "TI DaVinci VPIF V4L2-Display driver"
+	depends on V4L_PLATFORM_DRIVERS
+	depends on VIDEO_DEV
+	depends on ARCH_DAVINCI || COMPILE_TEST
+	depends on I2C
+	select VIDEOBUF2_DMA_CONTIG
+	select VIDEO_ADV7343 if MEDIA_SUBDRV_AUTOSELECT
+	select VIDEO_THS7303 if MEDIA_SUBDRV_AUTOSELECT
+	help
+	  Enables Davinci VPIF module used for display devices.
+	  This module is used for display on TI DM6467/DA850/OMAPL138
+	  SoCs.
+
+	  To compile this driver as a module, choose M here. There will
+	  be two modules called vpif.ko and vpif_display.ko
+
+config VIDEO_DAVINCI_VPIF_CAPTURE
+	tristate "TI DaVinci VPIF video capture driver"
+	depends on V4L_PLATFORM_DRIVERS
+	depends on VIDEO_DEV
+	depends on ARCH_DAVINCI || COMPILE_TEST
+	depends on I2C
+	select VIDEOBUF2_DMA_CONTIG
+	select V4L2_FWNODE
+	help
+	  Enables Davinci VPIF module used for capture devices.
+	  This module is used for capture on TI DM6467/DA850/OMAPL138
+	  SoCs.
+
+	  To compile this driver as a module, choose M here. There will
+	  be two modules called vpif.ko and vpif_capture.ko

linux-7.2.3/drivers/media/platform/ti/davinci/Makefile

@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the davinci video device drivers.
+#
+
+#VPIF Display driver
+obj-$(CONFIG_VIDEO_DAVINCI_VPIF_DISPLAY) += vpif.o vpif_display.o
+#VPIF Capture driver
+obj-$(CONFIG_VIDEO_DAVINCI_VPIF_CAPTURE) += vpif.o vpif_capture.o

linux-7.2.3/drivers/media/platform/ti/davinci/vpif.c

@@ -0,0 +1,609 @@
+/*
+ * vpif - Video Port Interface driver
+ * VPIF is a receiver and transmitter for video data. It has two channels(0, 1)
+ * that receiving video byte stream and two channels(2, 3) for video output.
+ * The hardware supports SDTV, HDTV formats, raw data capture.
+ * Currently, the driver supports NTSC and PAL standards.
+ *
+ * Copyright (C) 2009 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed .as is. WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/spinlock.h>
+#include <linux/v4l2-dv-timings.h>
+#include <linux/of_graph.h>
+
+#include "vpif.h"
+
+MODULE_DESCRIPTION("TI DaVinci Video Port Interface driver");
+MODULE_LICENSE("GPL");
+
+#define VPIF_DRIVER_NAME	"vpif"
+MODULE_ALIAS("platform:" VPIF_DRIVER_NAME);
+
+#define VPIF_CH0_MAX_MODES	22
+#define VPIF_CH1_MAX_MODES	2
+#define VPIF_CH2_MAX_MODES	15
+#define VPIF_CH3_MAX_MODES	2
+
+struct vpif_data {
+	struct platform_device *capture;
+	struct platform_device *display;
+};
+
+DEFINE_SPINLOCK(vpif_lock);
+EXPORT_SYMBOL_GPL(vpif_lock);
+
+void __iomem *vpif_base;
+EXPORT_SYMBOL_GPL(vpif_base);
+
+/*
+ * vpif_ch_params: video standard configuration parameters for vpif
+ *
+ * The table must include all presets from supported subdevices.
+ */
+const struct vpif_channel_config_params vpif_ch_params[] = {
+	/* HDTV formats */
+	{
+		.name = "480p59_94",
+		.width = 720,
+		.height = 480,
+		.frm_fmt = 1,
+		.ycmux_mode = 0,
+		.eav2sav = 138-8,
+		.sav2eav = 720,
+		.l1 = 1,
+		.l3 = 43,
+		.l5 = 523,
+		.vsize = 525,
+		.capture_format = 0,
+		.vbi_supported = 0,
+		.hd_sd = 1,
+		.dv_timings = V4L2_DV_BT_CEA_720X480P59_94,
+	},
+	{
+		.name = "576p50",
+		.width = 720,
+		.height = 576,
+		.frm_fmt = 1,
+		.ycmux_mode = 0,
+		.eav2sav = 144-8,
+		.sav2eav = 720,
+		.l1 = 1,
+		.l3 = 45,
+		.l5 = 621,
+		.vsize = 625,
+		.capture_format = 0,
+		.vbi_supported = 0,
+		.hd_sd = 1,
+		.dv_timings = V4L2_DV_BT_CEA_720X576P50,
+	},
+	{
+		.name = "720p50",
+		.width = 1280,
+		.height = 720,
+		.frm_fmt = 1,
+		.ycmux_mode = 0,
+		.eav2sav = 700-8,
+		.sav2eav = 1280,
+		.l1 = 1,
+		.l3 = 26,
+		.l5 = 746,
+		.vsize = 750,
+		.capture_format = 0,
+		.vbi_supported = 0,
+		.hd_sd = 1,
+		.dv_timings = V4L2_DV_BT_CEA_1280X720P50,
+	},
+	{
+		.name = "720p60",
+		.width = 1280,
+		.height = 720,
+		.frm_fmt = 1,
+		.ycmux_mode = 0,
+		.eav2sav = 370 - 8,
+		.sav2eav = 1280,
+		.l1 = 1,
+		.l3 = 26,
+		.l5 = 746,
+		.vsize = 750,
+		.capture_format = 0,
+		.vbi_supported = 0,
+		.hd_sd = 1,
+		.dv_timings = V4L2_DV_BT_CEA_1280X720P60,
+	},
+	{
+		.name = "1080I50",
+		.width = 1920,
+		.height = 1080,
+		.frm_fmt = 0,
+		.ycmux_mode = 0,
+		.eav2sav = 720 - 8,
+		.sav2eav = 1920,
+		.l1 = 1,
+		.l3 = 21,
+		.l5 = 561,
+		.l7 = 563,
+		.l9 = 584,
+		.l11 = 1124,
+		.vsize = 1125,
+		.capture_format = 0,
+		.vbi_supported = 0,
+		.hd_sd = 1,
+		.dv_timings = V4L2_DV_BT_CEA_1920X1080I50,
+	},
+	{
+		.name = "1080I60",
+		.width = 1920,
+		.height = 1080,
+		.frm_fmt = 0,
+		.ycmux_mode = 0,
+		.eav2sav = 280 - 8,
+		.sav2eav = 1920,
+		.l1 = 1,
+		.l3 = 21,
+		.l5 = 561,
+		.l7 = 563,
+		.l9 = 584,
+		.l11 = 1124,
+		.vsize = 1125,
+		.capture_format = 0,
+		.vbi_supported = 0,
+		.hd_sd = 1,
+		.dv_timings = V4L2_DV_BT_CEA_1920X1080I60,
+	},
+	{
+		.name = "1080p60",
+		.width = 1920,
+		.height = 1080,
+		.frm_fmt = 1,
+		.ycmux_mode = 0,
+		.eav2sav = 280 - 8,
+		.sav2eav = 1920,
+		.l1 = 1,
+		.l3 = 42,
+		.l5 = 1122,
+		.vsize = 1125,
+		.capture_format = 0,
+		.vbi_supported = 0,
+		.hd_sd = 1,
+		.dv_timings = V4L2_DV_BT_CEA_1920X1080P60,
+	},
+
+	/* SDTV formats */
+	{
+		.name = "NTSC_M",
+		.width = 720,
+		.height = 480,
+		.frm_fmt = 0,
+		.ycmux_mode = 1,
+		.eav2sav = 268,
+		.sav2eav = 1440,
+		.l1 = 1,
+		.l3 = 23,
+		.l5 = 263,
+		.l7 = 266,
+		.l9 = 286,
+		.l11 = 525,
+		.vsize = 525,
+		.capture_format = 0,
+		.vbi_supported = 1,
+		.hd_sd = 0,
+		.stdid = V4L2_STD_525_60,
+	},
+	{
+		.name = "PAL_BDGHIK",
+		.width = 720,
+		.height = 576,
+		.frm_fmt = 0,
+		.ycmux_mode = 1,
+		.eav2sav = 280,
+		.sav2eav = 1440,
+		.l1 = 1,
+		.l3 = 23,
+		.l5 = 311,
+		.l7 = 313,
+		.l9 = 336,
+		.l11 = 624,
+		.vsize = 625,
+		.capture_format = 0,
+		.vbi_supported = 1,
+		.hd_sd = 0,
+		.stdid = V4L2_STD_625_50,
+	},
+};
+EXPORT_SYMBOL_GPL(vpif_ch_params);
+
+const unsigned int vpif_ch_params_count = ARRAY_SIZE(vpif_ch_params);
+EXPORT_SYMBOL_GPL(vpif_ch_params_count);
+
+static inline void vpif_wr_bit(u32 reg, u32 bit, u32 val)
+{
+	if (val)
+		vpif_set_bit(reg, bit);
+	else
+		vpif_clr_bit(reg, bit);
+}
+
+/* This structure is used to keep track of VPIF size register's offsets */
+struct vpif_registers {
+	u32 h_cfg, v_cfg_00, v_cfg_01, v_cfg_02, v_cfg, ch_ctrl;
+	u32 line_offset, vanc0_strt, vanc0_size, vanc1_strt;
+	u32 vanc1_size, width_mask, len_mask;
+	u8 max_modes;
+};
+
+static const struct vpif_registers vpifregs[VPIF_NUM_CHANNELS] = {
+	/* Channel0 */
+	{
+		VPIF_CH0_H_CFG, VPIF_CH0_V_CFG_00, VPIF_CH0_V_CFG_01,
+		VPIF_CH0_V_CFG_02, VPIF_CH0_V_CFG_03, VPIF_CH0_CTRL,
+		VPIF_CH0_IMG_ADD_OFST, 0, 0, 0, 0, 0x1FFF, 0xFFF,
+		VPIF_CH0_MAX_MODES,
+	},
+	/* Channel1 */
+	{
+		VPIF_CH1_H_CFG, VPIF_CH1_V_CFG_00, VPIF_CH1_V_CFG_01,
+		VPIF_CH1_V_CFG_02, VPIF_CH1_V_CFG_03, VPIF_CH1_CTRL,
+		VPIF_CH1_IMG_ADD_OFST, 0, 0, 0, 0, 0x1FFF, 0xFFF,
+		VPIF_CH1_MAX_MODES,
+	},
+	/* Channel2 */
+	{
+		VPIF_CH2_H_CFG, VPIF_CH2_V_CFG_00, VPIF_CH2_V_CFG_01,
+		VPIF_CH2_V_CFG_02, VPIF_CH2_V_CFG_03, VPIF_CH2_CTRL,
+		VPIF_CH2_IMG_ADD_OFST, VPIF_CH2_VANC0_STRT, VPIF_CH2_VANC0_SIZE,
+		VPIF_CH2_VANC1_STRT, VPIF_CH2_VANC1_SIZE, 0x7FF, 0x7FF,
+		VPIF_CH2_MAX_MODES
+	},
+	/* Channel3 */
+	{
+		VPIF_CH3_H_CFG, VPIF_CH3_V_CFG_00, VPIF_CH3_V_CFG_01,
+		VPIF_CH3_V_CFG_02, VPIF_CH3_V_CFG_03, VPIF_CH3_CTRL,
+		VPIF_CH3_IMG_ADD_OFST, VPIF_CH3_VANC0_STRT, VPIF_CH3_VANC0_SIZE,
+		VPIF_CH3_VANC1_STRT, VPIF_CH3_VANC1_SIZE, 0x7FF, 0x7FF,
+		VPIF_CH3_MAX_MODES
+	},
+};
+
+/* vpif_set_mode_info:
+ * This function is used to set horizontal and vertical config parameters
+ * As per the standard in the channel, configure the values of L1, L3,
+ * L5, L7  L9, L11 in VPIF Register , also write width and height
+ */
+static void vpif_set_mode_info(const struct vpif_channel_config_params *config,
+				u8 channel_id, u8 config_channel_id)
+{
+	u32 value;
+
+	value = (config->eav2sav & vpifregs[config_channel_id].width_mask);
+	value <<= VPIF_CH_LEN_SHIFT;
+	value |= (config->sav2eav & vpifregs[config_channel_id].width_mask);
+	regw(value, vpifregs[channel_id].h_cfg);
+
+	value = (config->l1 & vpifregs[config_channel_id].len_mask);
+	value <<= VPIF_CH_LEN_SHIFT;
+	value |= (config->l3 & vpifregs[config_channel_id].len_mask);
+	regw(value, vpifregs[channel_id].v_cfg_00);
+
+	value = (config->l5 & vpifregs[config_channel_id].len_mask);
+	value <<= VPIF_CH_LEN_SHIFT;
+	value |= (config->l7 & vpifregs[config_channel_id].len_mask);
+	regw(value, vpifregs[channel_id].v_cfg_01);
+
+	value = (config->l9 & vpifregs[config_channel_id].len_mask);
+	value <<= VPIF_CH_LEN_SHIFT;
+	value |= (config->l11 & vpifregs[config_channel_id].len_mask);
+	regw(value, vpifregs[channel_id].v_cfg_02);
+
+	value = (config->vsize & vpifregs[config_channel_id].len_mask);
+	regw(value, vpifregs[channel_id].v_cfg);
+}
+
+/* config_vpif_params
+ * Function to set the parameters of a channel
+ * Mainly modifies the channel ciontrol register
+ * It sets frame format, yc mux mode
+ */
+static void config_vpif_params(struct vpif_params *vpifparams,
+				u8 channel_id, u8 found)
+{
+	const struct vpif_channel_config_params *config = &vpifparams->std_info;
+	u32 value, ch_nip, reg;
+	u8 start, end;
+	int i;
+
+	start = channel_id;
+	end = channel_id + found;
+
+	for (i = start; i < end; i++) {
+		reg = vpifregs[i].ch_ctrl;
+		if (channel_id < 2)
+			ch_nip = VPIF_CAPTURE_CH_NIP;
+		else
+			ch_nip = VPIF_DISPLAY_CH_NIP;
+
+		vpif_wr_bit(reg, ch_nip, config->frm_fmt);
+		vpif_wr_bit(reg, VPIF_CH_YC_MUX_BIT, config->ycmux_mode);
+		vpif_wr_bit(reg, VPIF_CH_INPUT_FIELD_FRAME_BIT,
+					vpifparams->video_params.storage_mode);
+
+		/* Set raster scanning SDR Format */
+		vpif_clr_bit(reg, VPIF_CH_SDR_FMT_BIT);
+		vpif_wr_bit(reg, VPIF_CH_DATA_MODE_BIT, config->capture_format);
+
+		if (channel_id > 1)	/* Set the Pixel enable bit */
+			vpif_set_bit(reg, VPIF_DISPLAY_PIX_EN_BIT);
+		else if (config->capture_format) {
+			/* Set the polarity of various pins */
+			vpif_wr_bit(reg, VPIF_CH_FID_POLARITY_BIT,
+					vpifparams->iface.fid_pol);
+			vpif_wr_bit(reg, VPIF_CH_V_VALID_POLARITY_BIT,
+					vpifparams->iface.vd_pol);
+			vpif_wr_bit(reg, VPIF_CH_H_VALID_POLARITY_BIT,
+					vpifparams->iface.hd_pol);
+
+			value = regr(reg);
+			/* Set data width */
+			value &= ~(0x3u <<
+					VPIF_CH_DATA_WIDTH_BIT);
+			value |= ((vpifparams->params.data_sz) <<
+						     VPIF_CH_DATA_WIDTH_BIT);
+			regw(value, reg);
+		}
+
+		/* Write the pitch in the driver */
+		regw((vpifparams->video_params.hpitch),
+						vpifregs[i].line_offset);
+	}
+}
+
+/* vpif_set_video_params
+ * This function is used to set video parameters in VPIF register
+ */
+int vpif_set_video_params(struct vpif_params *vpifparams, u8 channel_id)
+{
+	const struct vpif_channel_config_params *config = &vpifparams->std_info;
+	int found = 1;
+
+	vpif_set_mode_info(config, channel_id, channel_id);
+	if (!config->ycmux_mode) {
+		/* YC are on separate channels (HDTV formats) */
+		vpif_set_mode_info(config, channel_id + 1, channel_id);
+		found = 2;
+	}
+
+	config_vpif_params(vpifparams, channel_id, found);
+
+	regw(0x80, VPIF_REQ_SIZE);
+	regw(0x01, VPIF_EMULATION_CTRL);
+
+	return found;
+}
+EXPORT_SYMBOL(vpif_set_video_params);
+
+void vpif_set_vbi_display_params(struct vpif_vbi_params *vbiparams,
+				u8 channel_id)
+{
+	u32 value;
+
+	value = 0x3F8 & (vbiparams->hstart0);
+	value |= 0x3FFFFFF & ((vbiparams->vstart0) << 16);
+	regw(value, vpifregs[channel_id].vanc0_strt);
+
+	value = 0x3F8 & (vbiparams->hstart1);
+	value |= 0x3FFFFFF & ((vbiparams->vstart1) << 16);
+	regw(value, vpifregs[channel_id].vanc1_strt);
+
+	value = 0x3F8 & (vbiparams->hsize0);
+	value |= 0x3FFFFFF & ((vbiparams->vsize0) << 16);
+	regw(value, vpifregs[channel_id].vanc0_size);
+
+	value = 0x3F8 & (vbiparams->hsize1);
+	value |= 0x3FFFFFF & ((vbiparams->vsize1) << 16);
+	regw(value, vpifregs[channel_id].vanc1_size);
+
+}
+EXPORT_SYMBOL(vpif_set_vbi_display_params);
+
+int vpif_channel_getfid(u8 channel_id)
+{
+	return (regr(vpifregs[channel_id].ch_ctrl) & VPIF_CH_FID_MASK)
+					>> VPIF_CH_FID_SHIFT;
+}
+EXPORT_SYMBOL(vpif_channel_getfid);
+
+static void vpif_pdev_release(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+
+	kfree(pdev);
+}
+
+static int vpif_probe(struct platform_device *pdev)
+{
+	static struct resource res_irq;
+	struct platform_device *pdev_capture, *pdev_display;
+	struct device_node *endpoint = NULL;
+	struct vpif_data *data;
+	int ret;
+	int irq;
+
+	vpif_base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(vpif_base))
+		return PTR_ERR(vpif_base);
+
+	data = kzalloc_obj(*data);
+	if (!data)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, data);
+
+	pm_runtime_enable(&pdev->dev);
+	pm_runtime_get(&pdev->dev);
+
+	/*
+	 * If VPIF Node has endpoints, assume "new" DT support,
+	 * where capture and display drivers don't have DT nodes
+	 * so their devices need to be registered manually here
+	 * for their legacy platform_drivers to work.
+	 */
+	endpoint = of_graph_get_endpoint_by_regs(pdev->dev.of_node, 0, -1);
+	if (!endpoint)
+		return 0;
+	of_node_put(endpoint);
+
+	/*
+	 * For DT platforms, manually create platform_devices for
+	 * capture/display drivers.
+	 */
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		ret = irq;
+		goto err_put_rpm;
+	}
+	res_irq = DEFINE_RES_IRQ_NAMED(irq, of_node_full_name(pdev->dev.of_node));
+	res_irq.flags |= irq_get_trigger_type(irq);
+
+	pdev_capture = kzalloc_obj(*pdev_capture);
+	if (!pdev_capture) {
+		ret = -ENOMEM;
+		goto err_put_rpm;
+	}
+
+	pdev_capture->name = "vpif_capture";
+	pdev_capture->id = -1;
+	pdev_capture->resource = &res_irq;
+	pdev_capture->num_resources = 1;
+	pdev_capture->dev.dma_mask = pdev->dev.dma_mask;
+	pdev_capture->dev.coherent_dma_mask = pdev->dev.coherent_dma_mask;
+	pdev_capture->dev.parent = &pdev->dev;
+	pdev_capture->dev.release = vpif_pdev_release;
+
+	ret = platform_device_register(pdev_capture);
+	if (ret)
+		goto err_put_pdev_capture;
+
+	pdev_display = kzalloc_obj(*pdev_display);
+	if (!pdev_display) {
+		ret = -ENOMEM;
+		goto err_del_pdev_capture;
+	}
+
+	pdev_display->name = "vpif_display";
+	pdev_display->id = -1;
+	pdev_display->resource = &res_irq;
+	pdev_display->num_resources = 1;
+	pdev_display->dev.dma_mask = pdev->dev.dma_mask;
+	pdev_display->dev.coherent_dma_mask = pdev->dev.coherent_dma_mask;
+	pdev_display->dev.parent = &pdev->dev;
+	pdev_display->dev.release = vpif_pdev_release;
+
+	ret = platform_device_register(pdev_display);
+	if (ret)
+		goto err_put_pdev_display;
+
+	data->capture = pdev_capture;
+	data->display = pdev_display;
+
+	return 0;
+
+err_put_pdev_display:
+	platform_device_put(pdev_display);
+err_del_pdev_capture:
+	platform_device_del(pdev_capture);
+err_put_pdev_capture:
+	platform_device_put(pdev_capture);
+err_put_rpm:
+	pm_runtime_put(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+	kfree(data);
+
+	return ret;
+}
+
+static void vpif_remove(struct platform_device *pdev)
+{
+	struct vpif_data *data = platform_get_drvdata(pdev);
+
+	if (data->capture)
+		platform_device_unregister(data->capture);
+	if (data->display)
+		platform_device_unregister(data->display);
+
+	pm_runtime_put(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+
+	kfree(data);
+}
+
+#ifdef CONFIG_PM
+static int vpif_suspend(struct device *dev)
+{
+	pm_runtime_put(dev);
+	return 0;
+}
+
+static int vpif_resume(struct device *dev)
+{
+	pm_runtime_get(dev);
+	return 0;
+}
+
+static const struct dev_pm_ops vpif_pm = {
+	.suspend        = vpif_suspend,
+	.resume         = vpif_resume,
+};
+
+#define vpif_pm_ops (&vpif_pm)
+#else
+#define vpif_pm_ops NULL
+#endif
+
+#if IS_ENABLED(CONFIG_OF)
+static const struct of_device_id vpif_of_match[] = {
+	{ .compatible = "ti,da850-vpif", },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, vpif_of_match);
+#endif
+
+static struct platform_driver vpif_driver = {
+	.driver = {
+		.of_match_table = of_match_ptr(vpif_of_match),
+		.name	= VPIF_DRIVER_NAME,
+		.pm	= vpif_pm_ops,
+	},
+	.remove = vpif_remove,
+	.probe = vpif_probe,
+};
+
+static void vpif_exit(void)
+{
+	platform_driver_unregister(&vpif_driver);
+}
+
+static int __init vpif_init(void)
+{
+	return platform_driver_register(&vpif_driver);
+}
+subsys_initcall(vpif_init);
+module_exit(vpif_exit);
+

linux-7.2.3/drivers/media/platform/ti/davinci/vpif.h

@@ -0,0 +1,679 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * VPIF header file
+ *
+ * Copyright (C) 2009 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#ifndef VPIF_H
+#define VPIF_H
+
+#include <linux/io.h>
+#include <linux/videodev2.h>
+#include <media/davinci/vpif_types.h>
+
+/* Maximum channel allowed */
+#define VPIF_NUM_CHANNELS		(4)
+#define VPIF_CAPTURE_NUM_CHANNELS	(2)
+#define VPIF_DISPLAY_NUM_CHANNELS	(2)
+
+/* Macros to read/write registers */
+extern void __iomem *vpif_base;
+extern spinlock_t vpif_lock;
+
+#define regr(reg)               readl((reg) + vpif_base)
+#define regw(value, reg)        writel(value, (reg + vpif_base))
+
+/* Register Address Offsets */
+#define VPIF_PID			(0x0000)
+#define VPIF_CH0_CTRL			(0x0004)
+#define VPIF_CH1_CTRL			(0x0008)
+#define VPIF_CH2_CTRL			(0x000C)
+#define VPIF_CH3_CTRL			(0x0010)
+
+#define VPIF_INTEN			(0x0020)
+#define VPIF_INTEN_SET			(0x0024)
+#define VPIF_INTEN_CLR			(0x0028)
+#define VPIF_STATUS			(0x002C)
+#define VPIF_STATUS_CLR			(0x0030)
+#define VPIF_EMULATION_CTRL		(0x0034)
+#define VPIF_REQ_SIZE			(0x0038)
+
+#define VPIF_CH0_TOP_STRT_ADD_LUMA	(0x0040)
+#define VPIF_CH0_BTM_STRT_ADD_LUMA	(0x0044)
+#define VPIF_CH0_TOP_STRT_ADD_CHROMA	(0x0048)
+#define VPIF_CH0_BTM_STRT_ADD_CHROMA	(0x004c)
+#define VPIF_CH0_TOP_STRT_ADD_HANC	(0x0050)
+#define VPIF_CH0_BTM_STRT_ADD_HANC	(0x0054)
+#define VPIF_CH0_TOP_STRT_ADD_VANC	(0x0058)
+#define VPIF_CH0_BTM_STRT_ADD_VANC	(0x005c)
+#define VPIF_CH0_SP_CFG			(0x0060)
+#define VPIF_CH0_IMG_ADD_OFST		(0x0064)
+#define VPIF_CH0_HANC_ADD_OFST		(0x0068)
+#define VPIF_CH0_H_CFG			(0x006c)
+#define VPIF_CH0_V_CFG_00		(0x0070)
+#define VPIF_CH0_V_CFG_01		(0x0074)
+#define VPIF_CH0_V_CFG_02		(0x0078)
+#define VPIF_CH0_V_CFG_03		(0x007c)
+
+#define VPIF_CH1_TOP_STRT_ADD_LUMA	(0x0080)
+#define VPIF_CH1_BTM_STRT_ADD_LUMA	(0x0084)
+#define VPIF_CH1_TOP_STRT_ADD_CHROMA	(0x0088)
+#define VPIF_CH1_BTM_STRT_ADD_CHROMA	(0x008c)
+#define VPIF_CH1_TOP_STRT_ADD_HANC	(0x0090)
+#define VPIF_CH1_BTM_STRT_ADD_HANC	(0x0094)
+#define VPIF_CH1_TOP_STRT_ADD_VANC	(0x0098)
+#define VPIF_CH1_BTM_STRT_ADD_VANC	(0x009c)
+#define VPIF_CH1_SP_CFG			(0x00a0)
+#define VPIF_CH1_IMG_ADD_OFST		(0x00a4)
+#define VPIF_CH1_HANC_ADD_OFST		(0x00a8)
+#define VPIF_CH1_H_CFG			(0x00ac)
+#define VPIF_CH1_V_CFG_00		(0x00b0)
+#define VPIF_CH1_V_CFG_01		(0x00b4)
+#define VPIF_CH1_V_CFG_02		(0x00b8)
+#define VPIF_CH1_V_CFG_03		(0x00bc)
+
+#define VPIF_CH2_TOP_STRT_ADD_LUMA	(0x00c0)
+#define VPIF_CH2_BTM_STRT_ADD_LUMA	(0x00c4)
+#define VPIF_CH2_TOP_STRT_ADD_CHROMA	(0x00c8)
+#define VPIF_CH2_BTM_STRT_ADD_CHROMA	(0x00cc)
+#define VPIF_CH2_TOP_STRT_ADD_HANC	(0x00d0)
+#define VPIF_CH2_BTM_STRT_ADD_HANC	(0x00d4)
+#define VPIF_CH2_TOP_STRT_ADD_VANC	(0x00d8)
+#define VPIF_CH2_BTM_STRT_ADD_VANC	(0x00dc)
+#define VPIF_CH2_SP_CFG			(0x00e0)
+#define VPIF_CH2_IMG_ADD_OFST		(0x00e4)
+#define VPIF_CH2_HANC_ADD_OFST		(0x00e8)
+#define VPIF_CH2_H_CFG			(0x00ec)
+#define VPIF_CH2_V_CFG_00		(0x00f0)
+#define VPIF_CH2_V_CFG_01		(0x00f4)
+#define VPIF_CH2_V_CFG_02		(0x00f8)
+#define VPIF_CH2_V_CFG_03		(0x00fc)
+#define VPIF_CH2_HANC0_STRT		(0x0100)
+#define VPIF_CH2_HANC0_SIZE		(0x0104)
+#define VPIF_CH2_HANC1_STRT		(0x0108)
+#define VPIF_CH2_HANC1_SIZE		(0x010c)
+#define VPIF_CH2_VANC0_STRT		(0x0110)
+#define VPIF_CH2_VANC0_SIZE		(0x0114)
+#define VPIF_CH2_VANC1_STRT		(0x0118)
+#define VPIF_CH2_VANC1_SIZE		(0x011c)
+
+#define VPIF_CH3_TOP_STRT_ADD_LUMA	(0x0140)
+#define VPIF_CH3_BTM_STRT_ADD_LUMA	(0x0144)
+#define VPIF_CH3_TOP_STRT_ADD_CHROMA	(0x0148)
+#define VPIF_CH3_BTM_STRT_ADD_CHROMA	(0x014c)
+#define VPIF_CH3_TOP_STRT_ADD_HANC	(0x0150)
+#define VPIF_CH3_BTM_STRT_ADD_HANC	(0x0154)
+#define VPIF_CH3_TOP_STRT_ADD_VANC	(0x0158)
+#define VPIF_CH3_BTM_STRT_ADD_VANC	(0x015c)
+#define VPIF_CH3_SP_CFG			(0x0160)
+#define VPIF_CH3_IMG_ADD_OFST		(0x0164)
+#define VPIF_CH3_HANC_ADD_OFST		(0x0168)
+#define VPIF_CH3_H_CFG			(0x016c)
+#define VPIF_CH3_V_CFG_00		(0x0170)
+#define VPIF_CH3_V_CFG_01		(0x0174)
+#define VPIF_CH3_V_CFG_02		(0x0178)
+#define VPIF_CH3_V_CFG_03		(0x017c)
+#define VPIF_CH3_HANC0_STRT		(0x0180)
+#define VPIF_CH3_HANC0_SIZE		(0x0184)
+#define VPIF_CH3_HANC1_STRT		(0x0188)
+#define VPIF_CH3_HANC1_SIZE		(0x018c)
+#define VPIF_CH3_VANC0_STRT		(0x0190)
+#define VPIF_CH3_VANC0_SIZE		(0x0194)
+#define VPIF_CH3_VANC1_STRT		(0x0198)
+#define VPIF_CH3_VANC1_SIZE		(0x019c)
+
+#define VPIF_IODFT_CTRL			(0x01c0)
+
+/* Functions for bit Manipulation */
+static inline void vpif_set_bit(u32 reg, u32 bit)
+{
+	regw((regr(reg)) | (0x01 << bit), reg);
+}
+
+static inline void vpif_clr_bit(u32 reg, u32 bit)
+{
+	regw(((regr(reg)) & ~(0x01 << bit)), reg);
+}
+
+/* Macro for Generating mask */
+#ifdef GENERATE_MASK
+#undef GENERATE_MASK
+#endif
+
+#define GENERATE_MASK(bits, pos) \
+		((((0xFFFFFFFF) << (32 - bits)) >> (32 - bits)) << pos)
+
+/* Bit positions in the channel control registers */
+#define VPIF_CH_DATA_MODE_BIT	(2)
+#define VPIF_CH_YC_MUX_BIT	(3)
+#define VPIF_CH_SDR_FMT_BIT	(4)
+#define VPIF_CH_HANC_EN_BIT	(8)
+#define VPIF_CH_VANC_EN_BIT	(9)
+
+#define VPIF_CAPTURE_CH_NIP	(10)
+#define VPIF_DISPLAY_CH_NIP	(11)
+
+#define VPIF_DISPLAY_PIX_EN_BIT	(10)
+
+#define VPIF_CH_INPUT_FIELD_FRAME_BIT	(12)
+
+#define VPIF_CH_FID_POLARITY_BIT	(15)
+#define VPIF_CH_V_VALID_POLARITY_BIT	(14)
+#define VPIF_CH_H_VALID_POLARITY_BIT	(13)
+#define VPIF_CH_DATA_WIDTH_BIT		(28)
+
+#define VPIF_CH_CLK_EDGE_CTRL_BIT	(31)
+
+/* Mask various length */
+#define VPIF_CH_EAVSAV_MASK	GENERATE_MASK(13, 0)
+#define VPIF_CH_LEN_MASK	GENERATE_MASK(12, 0)
+#define VPIF_CH_WIDTH_MASK	GENERATE_MASK(13, 0)
+#define VPIF_CH_LEN_SHIFT	(16)
+
+/* VPIF masks for registers */
+#define VPIF_REQ_SIZE_MASK	(0x1ff)
+
+/* bit posotion of interrupt vpif_ch_intr register */
+#define VPIF_INTEN_FRAME_CH0	(0x00000001)
+#define VPIF_INTEN_FRAME_CH1	(0x00000002)
+#define VPIF_INTEN_FRAME_CH2	(0x00000004)
+#define VPIF_INTEN_FRAME_CH3	(0x00000008)
+
+/* bit position of clock and channel enable in vpif_chn_ctrl register */
+
+#define VPIF_CH0_CLK_EN		(0x00000002)
+#define VPIF_CH0_EN		(0x00000001)
+#define VPIF_CH1_CLK_EN		(0x00000002)
+#define VPIF_CH1_EN		(0x00000001)
+#define VPIF_CH2_CLK_EN		(0x00000002)
+#define VPIF_CH2_EN		(0x00000001)
+#define VPIF_CH3_CLK_EN		(0x00000002)
+#define VPIF_CH3_EN		(0x00000001)
+#define VPIF_CH_CLK_EN		(0x00000002)
+#define VPIF_CH_EN		(0x00000001)
+
+#define VPIF_INT_TOP	(0x00)
+#define VPIF_INT_BOTTOM	(0x01)
+#define VPIF_INT_BOTH	(0x02)
+
+#define VPIF_CH0_INT_CTRL_SHIFT	(6)
+#define VPIF_CH1_INT_CTRL_SHIFT	(6)
+#define VPIF_CH2_INT_CTRL_SHIFT	(6)
+#define VPIF_CH3_INT_CTRL_SHIFT	(6)
+#define VPIF_CH_INT_CTRL_SHIFT	(6)
+
+#define VPIF_CH2_CLIP_ANC_EN	14
+#define VPIF_CH2_CLIP_ACTIVE_EN	13
+
+#define VPIF_CH3_CLIP_ANC_EN	14
+#define VPIF_CH3_CLIP_ACTIVE_EN	13
+
+/* enabled interrupt on both the fields on vpid_ch0_ctrl register */
+#define channel0_intr_assert()	(regw((regr(VPIF_CH0_CTRL)|\
+	(VPIF_INT_BOTH << VPIF_CH0_INT_CTRL_SHIFT)), VPIF_CH0_CTRL))
+
+/* enabled interrupt on both the fields on vpid_ch1_ctrl register */
+#define channel1_intr_assert()	(regw((regr(VPIF_CH1_CTRL)|\
+	(VPIF_INT_BOTH << VPIF_CH1_INT_CTRL_SHIFT)), VPIF_CH1_CTRL))
+
+/* enabled interrupt on both the fields on vpid_ch0_ctrl register */
+#define channel2_intr_assert()	(regw((regr(VPIF_CH2_CTRL)|\
+	(VPIF_INT_BOTH << VPIF_CH2_INT_CTRL_SHIFT)), VPIF_CH2_CTRL))
+
+/* enabled interrupt on both the fields on vpid_ch1_ctrl register */
+#define channel3_intr_assert()	(regw((regr(VPIF_CH3_CTRL)|\
+	(VPIF_INT_BOTH << VPIF_CH3_INT_CTRL_SHIFT)), VPIF_CH3_CTRL))
+
+#define VPIF_CH_FID_MASK	(0x20)
+#define VPIF_CH_FID_SHIFT	(5)
+
+#define VPIF_NTSC_VBI_START_FIELD0	(1)
+#define VPIF_NTSC_VBI_START_FIELD1	(263)
+#define VPIF_PAL_VBI_START_FIELD0	(624)
+#define VPIF_PAL_VBI_START_FIELD1	(311)
+
+#define VPIF_NTSC_HBI_START_FIELD0	(1)
+#define VPIF_NTSC_HBI_START_FIELD1	(263)
+#define VPIF_PAL_HBI_START_FIELD0	(624)
+#define VPIF_PAL_HBI_START_FIELD1	(311)
+
+#define VPIF_NTSC_VBI_COUNT_FIELD0	(20)
+#define VPIF_NTSC_VBI_COUNT_FIELD1	(19)
+#define VPIF_PAL_VBI_COUNT_FIELD0	(24)
+#define VPIF_PAL_VBI_COUNT_FIELD1	(25)
+
+#define VPIF_NTSC_HBI_COUNT_FIELD0	(263)
+#define VPIF_NTSC_HBI_COUNT_FIELD1	(262)
+#define VPIF_PAL_HBI_COUNT_FIELD0	(312)
+#define VPIF_PAL_HBI_COUNT_FIELD1	(313)
+
+#define VPIF_NTSC_VBI_SAMPLES_PER_LINE	(720)
+#define VPIF_PAL_VBI_SAMPLES_PER_LINE	(720)
+#define VPIF_NTSC_HBI_SAMPLES_PER_LINE	(268)
+#define VPIF_PAL_HBI_SAMPLES_PER_LINE	(280)
+
+#define VPIF_CH_VANC_EN			(0x20)
+#define VPIF_DMA_REQ_SIZE		(0x080)
+#define VPIF_EMULATION_DISABLE		(0x01)
+
+extern u8 irq_vpif_capture_channel[VPIF_NUM_CHANNELS];
+
+/* inline function to enable/disable channel0 */
+static inline void enable_channel0(int enable)
+{
+	if (enable)
+		regw((regr(VPIF_CH0_CTRL) | (VPIF_CH0_EN)), VPIF_CH0_CTRL);
+	else
+		regw((regr(VPIF_CH0_CTRL) & (~VPIF_CH0_EN)), VPIF_CH0_CTRL);
+}
+
+/* inline function to enable/disable channel1 */
+static inline void enable_channel1(int enable)
+{
+	if (enable)
+		regw((regr(VPIF_CH1_CTRL) | (VPIF_CH1_EN)), VPIF_CH1_CTRL);
+	else
+		regw((regr(VPIF_CH1_CTRL) & (~VPIF_CH1_EN)), VPIF_CH1_CTRL);
+}
+
+/* inline function to enable interrupt for channel0 */
+static inline void channel0_intr_enable(int enable)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&vpif_lock, flags);
+
+	if (enable) {
+		regw((regr(VPIF_INTEN) | 0x10), VPIF_INTEN);
+		regw((regr(VPIF_INTEN_SET) | 0x10), VPIF_INTEN_SET);
+
+		regw((regr(VPIF_INTEN) | VPIF_INTEN_FRAME_CH0), VPIF_INTEN);
+		regw((regr(VPIF_INTEN_SET) | VPIF_INTEN_FRAME_CH0),
+							VPIF_INTEN_SET);
+	} else {
+		regw((regr(VPIF_INTEN) & (~VPIF_INTEN_FRAME_CH0)), VPIF_INTEN);
+		regw((regr(VPIF_INTEN_SET) | VPIF_INTEN_FRAME_CH0),
+							VPIF_INTEN_SET);
+	}
+	spin_unlock_irqrestore(&vpif_lock, flags);
+}
+
+/* inline function to enable interrupt for channel1 */
+static inline void channel1_intr_enable(int enable)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&vpif_lock, flags);
+
+	if (enable) {
+		regw((regr(VPIF_INTEN) | 0x10), VPIF_INTEN);
+		regw((regr(VPIF_INTEN_SET) | 0x10), VPIF_INTEN_SET);
+
+		regw((regr(VPIF_INTEN) | VPIF_INTEN_FRAME_CH1), VPIF_INTEN);
+		regw((regr(VPIF_INTEN_SET) | VPIF_INTEN_FRAME_CH1),
+							VPIF_INTEN_SET);
+	} else {
+		regw((regr(VPIF_INTEN) & (~VPIF_INTEN_FRAME_CH1)), VPIF_INTEN);
+		regw((regr(VPIF_INTEN_SET) | VPIF_INTEN_FRAME_CH1),
+							VPIF_INTEN_SET);
+	}
+	spin_unlock_irqrestore(&vpif_lock, flags);
+}
+
+/* inline function to set buffer addresses in case of Y/C non mux mode */
+static inline void ch0_set_video_buf_addr_yc_nmux(unsigned long top_strt_luma,
+						  unsigned long btm_strt_luma,
+						  unsigned long top_strt_chroma,
+						  unsigned long btm_strt_chroma)
+{
+	regw(top_strt_luma, VPIF_CH0_TOP_STRT_ADD_LUMA);
+	regw(btm_strt_luma, VPIF_CH0_BTM_STRT_ADD_LUMA);
+	regw(top_strt_chroma, VPIF_CH1_TOP_STRT_ADD_CHROMA);
+	regw(btm_strt_chroma, VPIF_CH1_BTM_STRT_ADD_CHROMA);
+}
+
+/* inline function to set buffer addresses in VPIF registers for video data */
+static inline void ch0_set_video_buf_addr(unsigned long top_strt_luma,
+					  unsigned long btm_strt_luma,
+					  unsigned long top_strt_chroma,
+					  unsigned long btm_strt_chroma)
+{
+	regw(top_strt_luma, VPIF_CH0_TOP_STRT_ADD_LUMA);
+	regw(btm_strt_luma, VPIF_CH0_BTM_STRT_ADD_LUMA);
+	regw(top_strt_chroma, VPIF_CH0_TOP_STRT_ADD_CHROMA);
+	regw(btm_strt_chroma, VPIF_CH0_BTM_STRT_ADD_CHROMA);
+}
+
+static inline void ch1_set_video_buf_addr(unsigned long top_strt_luma,
+					  unsigned long btm_strt_luma,
+					  unsigned long top_strt_chroma,
+					  unsigned long btm_strt_chroma)
+{
+
+	regw(top_strt_luma, VPIF_CH1_TOP_STRT_ADD_LUMA);
+	regw(btm_strt_luma, VPIF_CH1_BTM_STRT_ADD_LUMA);
+	regw(top_strt_chroma, VPIF_CH1_TOP_STRT_ADD_CHROMA);
+	regw(btm_strt_chroma, VPIF_CH1_BTM_STRT_ADD_CHROMA);
+}
+
+static inline void ch0_set_vbi_addr(unsigned long top_vbi,
+	unsigned long btm_vbi, unsigned long a, unsigned long b)
+{
+	regw(top_vbi, VPIF_CH0_TOP_STRT_ADD_VANC);
+	regw(btm_vbi, VPIF_CH0_BTM_STRT_ADD_VANC);
+}
+
+static inline void ch0_set_hbi_addr(unsigned long top_vbi,
+	unsigned long btm_vbi, unsigned long a, unsigned long b)
+{
+	regw(top_vbi, VPIF_CH0_TOP_STRT_ADD_HANC);
+	regw(btm_vbi, VPIF_CH0_BTM_STRT_ADD_HANC);
+}
+
+static inline void ch1_set_vbi_addr(unsigned long top_vbi,
+	unsigned long btm_vbi, unsigned long a, unsigned long b)
+{
+	regw(top_vbi, VPIF_CH1_TOP_STRT_ADD_VANC);
+	regw(btm_vbi, VPIF_CH1_BTM_STRT_ADD_VANC);
+}
+
+static inline void ch1_set_hbi_addr(unsigned long top_vbi,
+	unsigned long btm_vbi, unsigned long a, unsigned long b)
+{
+	regw(top_vbi, VPIF_CH1_TOP_STRT_ADD_HANC);
+	regw(btm_vbi, VPIF_CH1_BTM_STRT_ADD_HANC);
+}
+
+/* Inline function to enable raw vbi in the given channel */
+static inline void disable_raw_feature(u8 channel_id, u8 index)
+{
+	u32 ctrl_reg;
+	if (0 == channel_id)
+		ctrl_reg = VPIF_CH0_CTRL;
+	else
+		ctrl_reg = VPIF_CH1_CTRL;
+
+	if (1 == index)
+		vpif_clr_bit(ctrl_reg, VPIF_CH_VANC_EN_BIT);
+	else
+		vpif_clr_bit(ctrl_reg, VPIF_CH_HANC_EN_BIT);
+}
+
+static inline void enable_raw_feature(u8 channel_id, u8 index)
+{
+	u32 ctrl_reg;
+	if (0 == channel_id)
+		ctrl_reg = VPIF_CH0_CTRL;
+	else
+		ctrl_reg = VPIF_CH1_CTRL;
+
+	if (1 == index)
+		vpif_set_bit(ctrl_reg, VPIF_CH_VANC_EN_BIT);
+	else
+		vpif_set_bit(ctrl_reg, VPIF_CH_HANC_EN_BIT);
+}
+
+/* inline function to enable/disable channel2 */
+static inline void enable_channel2(int enable)
+{
+	if (enable) {
+		regw((regr(VPIF_CH2_CTRL) | (VPIF_CH2_CLK_EN)), VPIF_CH2_CTRL);
+		regw((regr(VPIF_CH2_CTRL) | (VPIF_CH2_EN)), VPIF_CH2_CTRL);
+	} else {
+		regw((regr(VPIF_CH2_CTRL) & (~VPIF_CH2_CLK_EN)), VPIF_CH2_CTRL);
+		regw((regr(VPIF_CH2_CTRL) & (~VPIF_CH2_EN)), VPIF_CH2_CTRL);
+	}
+}
+
+/* inline function to enable/disable channel3 */
+static inline void enable_channel3(int enable)
+{
+	if (enable) {
+		regw((regr(VPIF_CH3_CTRL) | (VPIF_CH3_CLK_EN)), VPIF_CH3_CTRL);
+		regw((regr(VPIF_CH3_CTRL) | (VPIF_CH3_EN)), VPIF_CH3_CTRL);
+	} else {
+		regw((regr(VPIF_CH3_CTRL) & (~VPIF_CH3_CLK_EN)), VPIF_CH3_CTRL);
+		regw((regr(VPIF_CH3_CTRL) & (~VPIF_CH3_EN)), VPIF_CH3_CTRL);
+	}
+}
+
+/* inline function to enable interrupt for channel2 */
+static inline void channel2_intr_enable(int enable)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&vpif_lock, flags);
+
+	if (enable) {
+		regw((regr(VPIF_INTEN) | 0x10), VPIF_INTEN);
+		regw((regr(VPIF_INTEN_SET) | 0x10), VPIF_INTEN_SET);
+		regw((regr(VPIF_INTEN) | VPIF_INTEN_FRAME_CH2), VPIF_INTEN);
+		regw((regr(VPIF_INTEN_SET) | VPIF_INTEN_FRAME_CH2),
+							VPIF_INTEN_SET);
+	} else {
+		regw((regr(VPIF_INTEN) & (~VPIF_INTEN_FRAME_CH2)), VPIF_INTEN);
+		regw((regr(VPIF_INTEN_SET) | VPIF_INTEN_FRAME_CH2),
+							VPIF_INTEN_SET);
+	}
+	spin_unlock_irqrestore(&vpif_lock, flags);
+}
+
+/* inline function to enable interrupt for channel3 */
+static inline void channel3_intr_enable(int enable)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&vpif_lock, flags);
+
+	if (enable) {
+		regw((regr(VPIF_INTEN) | 0x10), VPIF_INTEN);
+		regw((regr(VPIF_INTEN_SET) | 0x10), VPIF_INTEN_SET);
+
+		regw((regr(VPIF_INTEN) | VPIF_INTEN_FRAME_CH3), VPIF_INTEN);
+		regw((regr(VPIF_INTEN_SET) | VPIF_INTEN_FRAME_CH3),
+							VPIF_INTEN_SET);
+	} else {
+		regw((regr(VPIF_INTEN) & (~VPIF_INTEN_FRAME_CH3)), VPIF_INTEN);
+		regw((regr(VPIF_INTEN_SET) | VPIF_INTEN_FRAME_CH3),
+							VPIF_INTEN_SET);
+	}
+	spin_unlock_irqrestore(&vpif_lock, flags);
+}
+
+/* inline function to enable raw vbi data for channel2 */
+static inline void channel2_raw_enable(int enable, u8 index)
+{
+	u32 mask;
+
+	if (1 == index)
+		mask = VPIF_CH_VANC_EN_BIT;
+	else
+		mask = VPIF_CH_HANC_EN_BIT;
+
+	if (enable)
+		vpif_set_bit(VPIF_CH2_CTRL, mask);
+	else
+		vpif_clr_bit(VPIF_CH2_CTRL, mask);
+}
+
+/* inline function to enable raw vbi data for channel3*/
+static inline void channel3_raw_enable(int enable, u8 index)
+{
+	u32 mask;
+
+	if (1 == index)
+		mask = VPIF_CH_VANC_EN_BIT;
+	else
+		mask = VPIF_CH_HANC_EN_BIT;
+
+	if (enable)
+		vpif_set_bit(VPIF_CH3_CTRL, mask);
+	else
+		vpif_clr_bit(VPIF_CH3_CTRL, mask);
+}
+
+/* function to enable clipping (for both active and blanking regions) on ch 2 */
+static inline void channel2_clipping_enable(int enable)
+{
+	if (enable) {
+		vpif_set_bit(VPIF_CH2_CTRL, VPIF_CH2_CLIP_ANC_EN);
+		vpif_set_bit(VPIF_CH2_CTRL, VPIF_CH2_CLIP_ACTIVE_EN);
+	} else {
+		vpif_clr_bit(VPIF_CH2_CTRL, VPIF_CH2_CLIP_ANC_EN);
+		vpif_clr_bit(VPIF_CH2_CTRL, VPIF_CH2_CLIP_ACTIVE_EN);
+	}
+}
+
+/* function to enable clipping (for both active and blanking regions) on ch 3 */
+static inline void channel3_clipping_enable(int enable)
+{
+	if (enable) {
+		vpif_set_bit(VPIF_CH3_CTRL, VPIF_CH3_CLIP_ANC_EN);
+		vpif_set_bit(VPIF_CH3_CTRL, VPIF_CH3_CLIP_ACTIVE_EN);
+	} else {
+		vpif_clr_bit(VPIF_CH3_CTRL, VPIF_CH3_CLIP_ANC_EN);
+		vpif_clr_bit(VPIF_CH3_CTRL, VPIF_CH3_CLIP_ACTIVE_EN);
+	}
+}
+
+/* inline function to set buffer addresses in case of Y/C non mux mode */
+static inline void ch2_set_video_buf_addr_yc_nmux(unsigned long top_strt_luma,
+						  unsigned long btm_strt_luma,
+						  unsigned long top_strt_chroma,
+						  unsigned long btm_strt_chroma)
+{
+	regw(top_strt_luma, VPIF_CH2_TOP_STRT_ADD_LUMA);
+	regw(btm_strt_luma, VPIF_CH2_BTM_STRT_ADD_LUMA);
+	regw(top_strt_chroma, VPIF_CH3_TOP_STRT_ADD_CHROMA);
+	regw(btm_strt_chroma, VPIF_CH3_BTM_STRT_ADD_CHROMA);
+}
+
+/* inline function to set buffer addresses in VPIF registers for video data */
+static inline void ch2_set_video_buf_addr(unsigned long top_strt_luma,
+					  unsigned long btm_strt_luma,
+					  unsigned long top_strt_chroma,
+					  unsigned long btm_strt_chroma)
+{
+	regw(top_strt_luma, VPIF_CH2_TOP_STRT_ADD_LUMA);
+	regw(btm_strt_luma, VPIF_CH2_BTM_STRT_ADD_LUMA);
+	regw(top_strt_chroma, VPIF_CH2_TOP_STRT_ADD_CHROMA);
+	regw(btm_strt_chroma, VPIF_CH2_BTM_STRT_ADD_CHROMA);
+}
+
+static inline void ch3_set_video_buf_addr(unsigned long top_strt_luma,
+					  unsigned long btm_strt_luma,
+					  unsigned long top_strt_chroma,
+					  unsigned long btm_strt_chroma)
+{
+	regw(top_strt_luma, VPIF_CH3_TOP_STRT_ADD_LUMA);
+	regw(btm_strt_luma, VPIF_CH3_BTM_STRT_ADD_LUMA);
+	regw(top_strt_chroma, VPIF_CH3_TOP_STRT_ADD_CHROMA);
+	regw(btm_strt_chroma, VPIF_CH3_BTM_STRT_ADD_CHROMA);
+}
+
+/* inline function to set buffer addresses in VPIF registers for vbi data */
+static inline void ch2_set_vbi_addr(unsigned long top_strt_luma,
+				    unsigned long btm_strt_luma,
+				    unsigned long top_strt_chroma,
+				    unsigned long btm_strt_chroma)
+{
+	regw(top_strt_luma, VPIF_CH2_TOP_STRT_ADD_VANC);
+	regw(btm_strt_luma, VPIF_CH2_BTM_STRT_ADD_VANC);
+}
+
+static inline void ch3_set_vbi_addr(unsigned long top_strt_luma,
+				    unsigned long btm_strt_luma,
+				    unsigned long top_strt_chroma,
+				    unsigned long btm_strt_chroma)
+{
+	regw(top_strt_luma, VPIF_CH3_TOP_STRT_ADD_VANC);
+	regw(btm_strt_luma, VPIF_CH3_BTM_STRT_ADD_VANC);
+}
+
+static inline int vpif_intr_status(int channel)
+{
+	int status = 0;
+	int mask;
+
+	if (channel < 0 || channel > 3)
+		return 0;
+
+	mask = 1 << channel;
+	status = regr(VPIF_STATUS) & mask;
+	regw(status, VPIF_STATUS_CLR);
+
+	return status;
+}
+
+#define VPIF_MAX_NAME	(30)
+
+/* This structure will store size parameters as per the mode selected by user */
+struct vpif_channel_config_params {
+	char name[VPIF_MAX_NAME];	/* Name of the mode */
+	u16 width;			/* Indicates width of the image */
+	u16 height;			/* Indicates height of the image */
+	u8 frm_fmt;			/* Interlaced (0) or progressive (1) */
+	u8 ycmux_mode;			/* This mode requires one (0) or two (1)
+					   channels */
+	u16 eav2sav;			/* length of eav 2 sav */
+	u16 sav2eav;			/* length of sav 2 eav */
+	u16 l1, l3, l5, l7, l9, l11;	/* Other parameter configurations */
+	u16 vsize;			/* Vertical size of the image */
+	u8 capture_format;		/* Indicates whether capture format
+					 * is in BT or in CCD/CMOS */
+	u8  vbi_supported;		/* Indicates whether this mode
+					 * supports capturing vbi or not */
+	u8 hd_sd;			/* HDTV (1) or SDTV (0) format */
+	v4l2_std_id stdid;		/* SDTV format */
+	struct v4l2_dv_timings dv_timings;	/* HDTV format */
+};
+
+extern const unsigned int vpif_ch_params_count;
+extern const struct vpif_channel_config_params vpif_ch_params[];
+
+struct vpif_video_params;
+struct vpif_params;
+struct vpif_vbi_params;
+
+int vpif_set_video_params(struct vpif_params *vpifparams, u8 channel_id);
+void vpif_set_vbi_display_params(struct vpif_vbi_params *vbiparams,
+							u8 channel_id);
+int vpif_channel_getfid(u8 channel_id);
+
+enum data_size {
+	_8BITS = 0,
+	_10BITS,
+	_12BITS,
+};
+
+/* Structure for vpif parameters for raw vbi data */
+struct vpif_vbi_params {
+	__u32 hstart0;  /* Horizontal start of raw vbi data for first field */
+	__u32 vstart0;  /* Vertical start of raw vbi data for first field */
+	__u32 hsize0;   /* Horizontal size of raw vbi data for first field */
+	__u32 vsize0;   /* Vertical size of raw vbi data for first field */
+	__u32 hstart1;  /* Horizontal start of raw vbi data for second field */
+	__u32 vstart1;  /* Vertical start of raw vbi data for second field */
+	__u32 hsize1;   /* Horizontal size of raw vbi data for second field */
+	__u32 vsize1;   /* Vertical size of raw vbi data for second field */
+};
+
+/* structure for vpif parameters */
+struct vpif_video_params {
+	__u8 storage_mode;	/* Indicates field or frame mode */
+	unsigned long hpitch;
+	v4l2_std_id stdid;
+};
+
+struct vpif_params {
+	struct vpif_interface iface;
+	struct vpif_video_params video_params;
+	struct vpif_channel_config_params std_info;
+	union param {
+		struct vpif_vbi_params	vbi_params;
+		enum data_size data_sz;
+	} params;
+};
+
+#endif				/* End of #ifndef VPIF_H */

linux-7.2.3/drivers/media/platform/ti/davinci/vpif_capture.h

@@ -0,0 +1,107 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2009 Texas Instruments Inc
+ */
+
+#ifndef VPIF_CAPTURE_H
+#define VPIF_CAPTURE_H
+
+/* Header files */
+#include <media/videobuf2-dma-contig.h>
+#include <media/v4l2-device.h>
+
+#include "vpif.h"
+
+/* Macros */
+#define VPIF_CAPTURE_VERSION		"0.0.2"
+
+#define VPIF_VALID_FIELD(field)		(((V4L2_FIELD_ANY == field) || \
+	(V4L2_FIELD_NONE == field)) || \
+	(((V4L2_FIELD_INTERLACED == field) || \
+	(V4L2_FIELD_SEQ_TB == field)) || \
+	(V4L2_FIELD_SEQ_BT == field)))
+
+#define VPIF_CAPTURE_MAX_DEVICES	2
+#define VPIF_VIDEO_INDEX		0
+#define VPIF_NUMBER_OF_OBJECTS		1
+
+/* Enumerated data type to give id to each device per channel */
+enum vpif_channel_id {
+	VPIF_CHANNEL0_VIDEO = 0,
+	VPIF_CHANNEL1_VIDEO,
+};
+
+struct video_obj {
+	enum v4l2_field buf_field;
+	/* Currently selected or default standard */
+	v4l2_std_id stdid;
+	struct v4l2_dv_timings dv_timings;
+};
+
+struct vpif_cap_buffer {
+	struct vb2_v4l2_buffer vb;
+	struct list_head list;
+};
+
+struct common_obj {
+	/* Pointer pointing to current v4l2_buffer */
+	struct vpif_cap_buffer *cur_frm;
+	/* Pointer pointing to current v4l2_buffer */
+	struct vpif_cap_buffer *next_frm;
+	/* Used to store pixel format */
+	struct v4l2_format fmt;
+	/* Buffer queue used in vb2 */
+	struct vb2_queue buffer_queue;
+	/* Queue of filled frames */
+	struct list_head dma_queue;
+	/* Protects the dma_queue field */
+	spinlock_t irqlock;
+	/* lock used to access this structure */
+	struct mutex lock;
+	/* Function pointer to set the addresses */
+	void (*set_addr) (unsigned long, unsigned long, unsigned long,
+			  unsigned long);
+	/* offset where Y top starts from the starting of the buffer */
+	u32 ytop_off;
+	/* offset where Y bottom starts from the starting of the buffer */
+	u32 ybtm_off;
+	/* offset where C top starts from the starting of the buffer */
+	u32 ctop_off;
+	/* offset where C bottom starts from the starting of the buffer */
+	u32 cbtm_off;
+	/* Indicates width of the image data */
+	u32 width;
+	/* Indicates height of the image data */
+	u32 height;
+};
+
+struct channel_obj {
+	/* Identifies video device for this channel */
+	struct video_device video_dev;
+	/* Indicates id of the field which is being displayed */
+	u32 field_id;
+	/* flag to indicate whether decoder is initialized */
+	u8 initialized;
+	/* Identifies channel */
+	enum vpif_channel_id channel_id;
+	/* Current input */
+	u32 input_idx;
+	/* subdev corresponding to the current input, may be NULL */
+	struct v4l2_subdev *sd;
+	/* vpif configuration params */
+	struct vpif_params vpifparams;
+	/* common object array */
+	struct common_obj common[VPIF_NUMBER_OF_OBJECTS];
+	/* video object */
+	struct video_obj video;
+};
+
+struct vpif_device {
+	struct v4l2_device v4l2_dev;
+	struct channel_obj *dev[VPIF_CAPTURE_NUM_CHANNELS];
+	struct v4l2_subdev **sd;
+	struct v4l2_async_notifier notifier;
+	struct vpif_capture_config *config;
+};
+
+#endif				/* VPIF_CAPTURE_H */

linux-7.2.3/drivers/media/platform/ti/davinci/vpif_display.h

@@ -0,0 +1,116 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * VPIF display header file
+ *
+ * Copyright (C) 2009 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#ifndef VPIF_DISPLAY_H
+#define VPIF_DISPLAY_H
+
+/* Header files */
+#include <media/videobuf2-dma-contig.h>
+#include <media/v4l2-device.h>
+
+#include "vpif.h"
+
+/* Macros */
+#define VPIF_DISPLAY_VERSION	"0.0.2"
+
+#define VPIF_VALID_FIELD(field) \
+	(((V4L2_FIELD_ANY == field) || (V4L2_FIELD_NONE == field)) || \
+	(((V4L2_FIELD_INTERLACED == field) || (V4L2_FIELD_SEQ_TB == field)) || \
+	(V4L2_FIELD_SEQ_BT == field)))
+
+#define VPIF_DISPLAY_MAX_DEVICES	(2)
+#define VPIF_SLICED_BUF_SIZE		(256)
+#define VPIF_SLICED_MAX_SERVICES	(3)
+#define VPIF_VIDEO_INDEX		(0)
+#define VPIF_VBI_INDEX			(1)
+#define VPIF_HBI_INDEX			(2)
+
+/* Setting it to 1 as HBI/VBI support yet to be added , else 3*/
+#define VPIF_NUMOBJECTS	(1)
+
+/* Macros */
+#define ISALIGNED(a)    (0 == ((a) & 7))
+
+/* enumerated data types */
+/* Enumerated data type to give id to each device per channel */
+enum vpif_channel_id {
+	VPIF_CHANNEL2_VIDEO = 0,	/* Channel2 Video */
+	VPIF_CHANNEL3_VIDEO,		/* Channel3 Video */
+};
+
+/* structures */
+
+struct video_obj {
+	enum v4l2_field buf_field;
+	u32 latest_only;		/* indicate whether to return
+					 * most recent displayed frame only */
+	v4l2_std_id stdid;		/* Currently selected or default
+					 * standard */
+	struct v4l2_dv_timings dv_timings;
+};
+
+struct vpif_disp_buffer {
+	struct vb2_v4l2_buffer vb;
+	struct list_head list;
+};
+
+struct common_obj {
+	struct vpif_disp_buffer *cur_frm;	/* Pointer pointing to current
+						 * vb2_buffer */
+	struct vpif_disp_buffer *next_frm;	/* Pointer pointing to next
+						 * vb2_buffer */
+	struct v4l2_format fmt;			/* Used to store the format */
+	struct vb2_queue buffer_queue;		/* Buffer queue used in vb2 */
+
+	struct list_head dma_queue;		/* Queue of filled frames */
+	spinlock_t irqlock;			/* Used for video buffer
+						 * handling */
+
+	/* channel specific parameters */
+	struct mutex lock;			/* lock used to access this
+						 * structure */
+	u32 ytop_off;				/* offset of Y top from the
+						 * starting of the buffer */
+	u32 ybtm_off;				/* offset of Y bottom from the
+						 * starting of the buffer */
+	u32 ctop_off;				/* offset of C top from the
+						 * starting of the buffer */
+	u32 cbtm_off;				/* offset of C bottom from the
+						 * starting of the buffer */
+	/* Function pointer to set the addresses */
+	void (*set_addr)(unsigned long, unsigned long,
+				unsigned long, unsigned long);
+	u32 height;
+	u32 width;
+};
+
+struct channel_obj {
+	/* V4l2 specific parameters */
+	struct video_device video_dev;	/* Identifies video device for
+					 * this channel */
+	u32 field_id;			/* Indicates id of the field
+					 * which is being displayed */
+	u8 initialized;			/* flag to indicate whether
+					 * encoder is initialized */
+	u32 output_idx;			/* Current output index */
+	struct v4l2_subdev *sd;		/* Current output subdev(may be NULL) */
+
+	enum vpif_channel_id channel_id;/* Identifies channel */
+	struct vpif_params vpifparams;
+	struct common_obj common[VPIF_NUMOBJECTS];
+	struct video_obj video;
+};
+
+/* vpif device structure */
+struct vpif_device {
+	struct v4l2_device v4l2_dev;
+	struct channel_obj *dev[VPIF_DISPLAY_NUM_CHANNELS];
+	struct v4l2_subdev **sd;
+	struct vpif_display_config *config;
+};
+
+#endif				/* VPIF_DISPLAY_H */

linux-7.2.3/drivers/media/platform/ti/j721e-csi2rx/Makefile

@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_VIDEO_TI_J721E_CSI2RX) += j721e-csi2rx.o

linux-7.2.3/drivers/media/platform/ti/omap/Kconfig

@@ -0,0 +1,17 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config VIDEO_OMAP2_VOUT_VRFB
+	bool
+	default y
+	depends on VIDEO_OMAP2_VOUT && (OMAP2_VRFB || COMPILE_TEST)
+
+config VIDEO_OMAP2_VOUT
+	tristate "OMAP2/OMAP3 V4L2-Display driver"
+	depends on V4L_PLATFORM_DRIVERS
+	depends on MMU
+	depends on FB_OMAP2 || (COMPILE_TEST && FB_OMAP2=n)
+	depends on ARCH_OMAP2 || ARCH_OMAP3 || COMPILE_TEST
+	depends on VIDEO_DEV
+	select VIDEOBUF2_DMA_CONTIG
+	select OMAP2_VRFB if ARCH_OMAP2 || ARCH_OMAP3
+	help
+	  V4L2 Display driver support for OMAP2/3 based boards.

linux-7.2.3/drivers/media/platform/ti/omap/Makefile

@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the omap video device drivers.
+#
+
+# OMAP2/3 Display driver
+omap-vout-y += omap_vout.o omap_voutlib.o
+omap-vout-$(CONFIG_VIDEO_OMAP2_VOUT_VRFB) += omap_vout_vrfb.o
+obj-$(CONFIG_VIDEO_OMAP2_VOUT) += omap-vout.o

linux-7.2.3/drivers/media/platform/ti/omap/omap_vout_vrfb.c

@@ -0,0 +1,419 @@
+/*
+ * omap_vout_vrfb.c
+ *
+ * Copyright (C) 2010 Texas Instruments.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ *
+ */
+
+#include <linux/sched.h>
+#include <linux/platform_device.h>
+#include <linux/videodev2.h>
+#include <linux/slab.h>
+
+#include <media/v4l2-device.h>
+
+#include <video/omapvrfb.h>
+
+#include "omap_voutdef.h"
+#include "omap_voutlib.h"
+#include "omap_vout_vrfb.h"
+
+#define OMAP_DMA_NO_DEVICE	0
+
+/*
+ * Function for allocating video buffers
+ */
+static int omap_vout_allocate_vrfb_buffers(struct omap_vout_device *vout,
+		unsigned int *count, int startindex)
+{
+	int i, j;
+
+	for (i = 0; i < *count; i++) {
+		if (!vout->smsshado_virt_addr[i]) {
+			vout->smsshado_virt_addr[i] =
+				omap_vout_alloc_buffer(vout->smsshado_size,
+						&vout->smsshado_phy_addr[i]);
+		}
+		if (!vout->smsshado_virt_addr[i] && startindex != -1) {
+			if (vout->vq.memory == V4L2_MEMORY_MMAP && i >= startindex)
+				break;
+		}
+		if (!vout->smsshado_virt_addr[i]) {
+			for (j = 0; j < i; j++) {
+				omap_vout_free_buffer(
+						vout->smsshado_virt_addr[j],
+						vout->smsshado_size);
+				vout->smsshado_virt_addr[j] = 0;
+				vout->smsshado_phy_addr[j] = 0;
+			}
+			*count = 0;
+			return -ENOMEM;
+		}
+		memset((void *)(long)vout->smsshado_virt_addr[i], 0,
+		       vout->smsshado_size);
+	}
+	return 0;
+}
+
+/*
+ * Wakes up the application once the DMA transfer to VRFB space is completed.
+ */
+static void omap_vout_vrfb_dma_tx_callback(void *data)
+{
+	struct vid_vrfb_dma *t = (struct vid_vrfb_dma *) data;
+
+	t->tx_status = 1;
+	wake_up_interruptible(&t->wait);
+}
+
+/*
+ * Free VRFB buffers
+ */
+void omap_vout_free_vrfb_buffers(struct omap_vout_device *vout)
+{
+	int j;
+
+	for (j = 0; j < VRFB_NUM_BUFS; j++) {
+		if (vout->smsshado_virt_addr[j]) {
+			omap_vout_free_buffer(vout->smsshado_virt_addr[j],
+					      vout->smsshado_size);
+			vout->smsshado_virt_addr[j] = 0;
+			vout->smsshado_phy_addr[j] = 0;
+		}
+	}
+}
+
+int omap_vout_setup_vrfb_bufs(struct platform_device *pdev, int vid_num,
+			      bool static_vrfb_allocation)
+{
+	int ret = 0, i, j;
+	struct omap_vout_device *vout;
+	struct video_device *vfd;
+	dma_cap_mask_t mask;
+	int image_width, image_height;
+	int vrfb_num_bufs = VRFB_NUM_BUFS;
+	struct v4l2_device *v4l2_dev = platform_get_drvdata(pdev);
+	struct omap2video_device *vid_dev =
+		container_of(v4l2_dev, struct omap2video_device, v4l2_dev);
+
+	vout = vid_dev->vouts[vid_num];
+	vfd = vout->vfd;
+
+	for (i = 0; i < VRFB_NUM_BUFS; i++) {
+		if (omap_vrfb_request_ctx(&vout->vrfb_context[i])) {
+			dev_info(&pdev->dev, ": VRFB allocation failed\n");
+			for (j = 0; j < i; j++)
+				omap_vrfb_release_ctx(&vout->vrfb_context[j]);
+			return -ENOMEM;
+		}
+	}
+
+	/* Calculate VRFB memory size */
+	/* allocate for worst case size */
+	image_width = VID_MAX_WIDTH / TILE_SIZE;
+	if (VID_MAX_WIDTH % TILE_SIZE)
+		image_width++;
+
+	image_width = image_width * TILE_SIZE;
+	image_height = VID_MAX_HEIGHT / TILE_SIZE;
+
+	if (VID_MAX_HEIGHT % TILE_SIZE)
+		image_height++;
+
+	image_height = image_height * TILE_SIZE;
+	vout->smsshado_size = PAGE_ALIGN(image_width * image_height * 2 * 2);
+
+	/*
+	 * Request and Initialize DMA, for DMA based VRFB transfer
+	 */
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_INTERLEAVE, mask);
+	vout->vrfb_dma_tx.chan = dma_request_chan_by_mask(&mask);
+	if (IS_ERR(vout->vrfb_dma_tx.chan)) {
+		vout->vrfb_dma_tx.req_status = DMA_CHAN_NOT_ALLOTED;
+	} else {
+		size_t xt_size = sizeof(struct dma_interleaved_template) +
+				 sizeof(struct data_chunk);
+
+		vout->vrfb_dma_tx.xt = kzalloc(xt_size, GFP_KERNEL);
+		if (!vout->vrfb_dma_tx.xt) {
+			dma_release_channel(vout->vrfb_dma_tx.chan);
+			vout->vrfb_dma_tx.req_status = DMA_CHAN_NOT_ALLOTED;
+		}
+	}
+
+	if (vout->vrfb_dma_tx.req_status == DMA_CHAN_NOT_ALLOTED)
+		dev_info(&pdev->dev,
+			 ": failed to allocate DMA Channel for video%d\n",
+			 vfd->minor);
+
+	init_waitqueue_head(&vout->vrfb_dma_tx.wait);
+
+	/*
+	 * statically allocated the VRFB buffer is done through
+	 * command line arguments
+	 */
+	if (static_vrfb_allocation) {
+		if (omap_vout_allocate_vrfb_buffers(vout, &vrfb_num_bufs, -1)) {
+			ret =  -ENOMEM;
+			goto release_vrfb_ctx;
+		}
+		vout->vrfb_static_allocation = true;
+	}
+	return 0;
+
+release_vrfb_ctx:
+	for (j = 0; j < VRFB_NUM_BUFS; j++)
+		omap_vrfb_release_ctx(&vout->vrfb_context[j]);
+	return ret;
+}
+
+/*
+ * Release the VRFB context once the module exits
+ */
+void omap_vout_release_vrfb(struct omap_vout_device *vout)
+{
+	int i;
+
+	for (i = 0; i < VRFB_NUM_BUFS; i++)
+		omap_vrfb_release_ctx(&vout->vrfb_context[i]);
+
+	if (vout->vrfb_dma_tx.req_status == DMA_CHAN_ALLOTED) {
+		vout->vrfb_dma_tx.req_status = DMA_CHAN_NOT_ALLOTED;
+		kfree(vout->vrfb_dma_tx.xt);
+		dmaengine_terminate_sync(vout->vrfb_dma_tx.chan);
+		dma_release_channel(vout->vrfb_dma_tx.chan);
+	}
+}
+
+/*
+ * Allocate the buffers for the VRFB space.  Data is copied from V4L2
+ * buffers to the VRFB buffers using the DMA engine.
+ */
+int omap_vout_vrfb_buffer_setup(struct omap_vout_device *vout,
+			  unsigned int *count, unsigned int startindex)
+{
+	int i;
+	bool yuv_mode;
+
+	if (!is_rotation_enabled(vout))
+		return 0;
+
+	/* If rotation is enabled, allocate memory for VRFB space also */
+	*count = *count > VRFB_NUM_BUFS ? VRFB_NUM_BUFS : *count;
+
+	/* Allocate the VRFB buffers only if the buffers are not
+	 * allocated during init time.
+	 */
+	if (!vout->vrfb_static_allocation)
+		if (omap_vout_allocate_vrfb_buffers(vout, count, startindex))
+			return -ENOMEM;
+
+	if (vout->dss_mode == OMAP_DSS_COLOR_YUV2 ||
+			vout->dss_mode == OMAP_DSS_COLOR_UYVY)
+		yuv_mode = true;
+	else
+		yuv_mode = false;
+
+	for (i = 0; i < *count; i++)
+		omap_vrfb_setup(&vout->vrfb_context[i],
+				vout->smsshado_phy_addr[i], vout->pix.width,
+				vout->pix.height, vout->bpp, yuv_mode);
+
+	return 0;
+}
+
+int omap_vout_prepare_vrfb(struct omap_vout_device *vout,
+			   struct vb2_buffer *vb)
+{
+	struct dma_async_tx_descriptor *tx;
+	enum dma_ctrl_flags flags = DMA_PREP_INTERRUPT | DMA_CTRL_ACK;
+	struct dma_chan *chan = vout->vrfb_dma_tx.chan;
+	struct dma_interleaved_template *xt = vout->vrfb_dma_tx.xt;
+	dma_cookie_t cookie;
+	dma_addr_t buf_phy_addr = vb2_dma_contig_plane_dma_addr(vb, 0);
+	enum dma_status status;
+	enum dss_rotation rotation;
+	size_t dst_icg;
+	u32 pixsize;
+
+	if (!is_rotation_enabled(vout))
+		return 0;
+
+	/* If rotation is enabled, copy input buffer into VRFB
+	 * memory space using DMA. We are copying input buffer
+	 * into VRFB memory space of desired angle and DSS will
+	 * read image VRFB memory for 0 degree angle
+	 */
+
+	pixsize = vout->bpp * vout->vrfb_bpp;
+	dst_icg = MAX_PIXELS_PER_LINE * pixsize - vout->pix.width * vout->bpp;
+
+	xt->src_start = buf_phy_addr;
+	xt->dst_start = vout->vrfb_context[vb->index].paddr[0];
+
+	xt->numf = vout->pix.height;
+	xt->frame_size = 1;
+	xt->sgl[0].size = vout->pix.width * vout->bpp;
+	xt->sgl[0].icg = dst_icg;
+
+	xt->dir = DMA_MEM_TO_MEM;
+	xt->src_sgl = false;
+	xt->src_inc = true;
+	xt->dst_sgl = true;
+	xt->dst_inc = true;
+
+	tx = dmaengine_prep_interleaved_dma(chan, xt, flags);
+	if (tx == NULL) {
+		pr_err("%s: DMA interleaved prep error\n", __func__);
+		return -EINVAL;
+	}
+
+	tx->callback = omap_vout_vrfb_dma_tx_callback;
+	tx->callback_param = &vout->vrfb_dma_tx;
+
+	cookie = dmaengine_submit(tx);
+	if (dma_submit_error(cookie)) {
+		pr_err("%s: dmaengine_submit failed (%d)\n", __func__, cookie);
+		return -EINVAL;
+	}
+
+	vout->vrfb_dma_tx.tx_status = 0;
+	dma_async_issue_pending(chan);
+
+	wait_event_interruptible_timeout(vout->vrfb_dma_tx.wait,
+					 vout->vrfb_dma_tx.tx_status == 1,
+					 VRFB_TX_TIMEOUT);
+
+	status = dma_async_is_tx_complete(chan, cookie, NULL, NULL);
+
+	if (vout->vrfb_dma_tx.tx_status == 0) {
+		pr_err("%s: Timeout while waiting for DMA\n", __func__);
+		dmaengine_terminate_sync(chan);
+		return -EINVAL;
+	} else if (status != DMA_COMPLETE) {
+		pr_err("%s: DMA completion %s status\n", __func__,
+		       status == DMA_ERROR ? "error" : "busy");
+		dmaengine_terminate_sync(chan);
+		return -EINVAL;
+	}
+
+	/* Store buffers physical address into an array. Addresses
+	 * from this array will be used to configure DSS */
+	rotation = calc_rotation(vout);
+	vout->queued_buf_addr[vb->index] =
+		vout->vrfb_context[vb->index].paddr[rotation];
+	return 0;
+}
+
+/*
+ * Calculate the buffer offsets from which the streaming should
+ * start. This offset calculation is mainly required because of
+ * the VRFB 32 pixels alignment with rotation.
+ */
+void omap_vout_calculate_vrfb_offset(struct omap_vout_device *vout)
+{
+	enum dss_rotation rotation;
+	bool mirroring = vout->mirror;
+	struct v4l2_rect *crop = &vout->crop;
+	struct v4l2_pix_format *pix = &vout->pix;
+	int *cropped_offset = &vout->cropped_offset;
+	int vr_ps = 1, ps = 2, temp_ps = 2;
+	int offset = 0, ctop = 0, cleft = 0, line_length = 0;
+
+	rotation = calc_rotation(vout);
+
+	if (V4L2_PIX_FMT_YUYV == pix->pixelformat ||
+			V4L2_PIX_FMT_UYVY == pix->pixelformat) {
+		if (is_rotation_enabled(vout)) {
+			/*
+			 * ps    - Actual pixel size for YUYV/UYVY for
+			 *         VRFB/Mirroring is 4 bytes
+			 * vr_ps - Virtually pixel size for YUYV/UYVY is
+			 *         2 bytes
+			 */
+			ps = 4;
+			vr_ps = 2;
+		} else {
+			ps = 2;	/* otherwise the pixel size is 2 byte */
+		}
+	} else if (V4L2_PIX_FMT_RGB32 == pix->pixelformat) {
+		ps = 4;
+	} else if (V4L2_PIX_FMT_RGB24 == pix->pixelformat) {
+		ps = 3;
+	}
+	vout->ps = ps;
+	vout->vr_ps = vr_ps;
+
+	if (is_rotation_enabled(vout)) {
+		line_length = MAX_PIXELS_PER_LINE;
+		ctop = (pix->height - crop->height) - crop->top;
+		cleft = (pix->width - crop->width) - crop->left;
+	} else {
+		line_length = pix->width;
+	}
+	vout->line_length = line_length;
+	switch (rotation) {
+	case dss_rotation_90_degree:
+		offset = vout->vrfb_context[0].yoffset *
+			vout->vrfb_context[0].bytespp;
+		temp_ps = ps / vr_ps;
+		if (!mirroring) {
+			*cropped_offset = offset + line_length *
+				temp_ps * cleft + crop->top * temp_ps;
+		} else {
+			*cropped_offset = offset + line_length * temp_ps *
+				cleft + crop->top * temp_ps + (line_length *
+				((crop->width / (vr_ps)) - 1) * ps);
+		}
+		break;
+	case dss_rotation_180_degree:
+		offset = ((MAX_PIXELS_PER_LINE * vout->vrfb_context[0].yoffset *
+			vout->vrfb_context[0].bytespp) +
+			(vout->vrfb_context[0].xoffset *
+			vout->vrfb_context[0].bytespp));
+		if (!mirroring) {
+			*cropped_offset = offset + (line_length * ps * ctop) +
+				(cleft / vr_ps) * ps;
+
+		} else {
+			*cropped_offset = offset + (line_length * ps * ctop) +
+				(cleft / vr_ps) * ps + (line_length *
+				(crop->height - 1) * ps);
+		}
+		break;
+	case dss_rotation_270_degree:
+		offset = MAX_PIXELS_PER_LINE * vout->vrfb_context[0].xoffset *
+			vout->vrfb_context[0].bytespp;
+		temp_ps = ps / vr_ps;
+		if (!mirroring) {
+			*cropped_offset = offset + line_length *
+			    temp_ps * crop->left + ctop * ps;
+		} else {
+			*cropped_offset = offset + line_length *
+				temp_ps * crop->left + ctop * ps +
+				(line_length * ((crop->width / vr_ps) - 1) *
+				 ps);
+		}
+		break;
+	case dss_rotation_0_degree:
+		if (!mirroring) {
+			*cropped_offset = (line_length * ps) *
+				crop->top + (crop->left / vr_ps) * ps;
+		} else {
+			*cropped_offset = (line_length * ps) *
+				crop->top + (crop->left / vr_ps) * ps +
+				(line_length * (crop->height - 1) * ps);
+		}
+		break;
+	default:
+		*cropped_offset = (line_length * ps * crop->top) /
+			vr_ps + (crop->left * ps) / vr_ps +
+			((crop->width / vr_ps) - 1) * ps;
+		break;
+	}
+}

linux-7.2.3/drivers/media/platform/ti/omap/omap_vout_vrfb.h

@@ -0,0 +1,40 @@
+/*
+ * omap_vout_vrfb.h
+ *
+ * Copyright (C) 2010 Texas Instruments.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ *
+ */
+
+#ifndef OMAP_VOUT_VRFB_H
+#define OMAP_VOUT_VRFB_H
+
+#ifdef CONFIG_VIDEO_OMAP2_VOUT_VRFB
+void omap_vout_free_vrfb_buffers(struct omap_vout_device *vout);
+int omap_vout_setup_vrfb_bufs(struct platform_device *pdev, int vid_num,
+			bool static_vrfb_allocation);
+void omap_vout_release_vrfb(struct omap_vout_device *vout);
+int omap_vout_vrfb_buffer_setup(struct omap_vout_device *vout,
+			unsigned int *count, unsigned int startindex);
+int omap_vout_prepare_vrfb(struct omap_vout_device *vout,
+			struct vb2_buffer *vb);
+void omap_vout_calculate_vrfb_offset(struct omap_vout_device *vout);
+#else
+static inline void omap_vout_free_vrfb_buffers(struct omap_vout_device *vout) { };
+static inline int omap_vout_setup_vrfb_bufs(struct platform_device *pdev, int vid_num,
+			bool static_vrfb_allocation)
+		{ return 0; };
+static inline void omap_vout_release_vrfb(struct omap_vout_device *vout) { };
+static inline int omap_vout_vrfb_buffer_setup(struct omap_vout_device *vout,
+			unsigned int *count, unsigned int startindex)
+		{ return 0; };
+static inline int omap_vout_prepare_vrfb(struct omap_vout_device *vout,
+			struct vb2_buffer *vb)
+		{ return 0; };
+static inline void omap_vout_calculate_vrfb_offset(struct omap_vout_device *vout) { };
+#endif
+
+#endif

linux-7.2.3/drivers/media/platform/ti/omap/omap_voutdef.h

@@ -0,0 +1,219 @@
+/*
+ * omap_voutdef.h
+ *
+ * Copyright (C) 2010 Texas Instruments.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef OMAP_VOUTDEF_H
+#define OMAP_VOUTDEF_H
+
+#include <media/videobuf2-dma-contig.h>
+#include <media/v4l2-ctrls.h>
+#include <video/omapfb_dss.h>
+#include <video/omapvrfb.h>
+#include <linux/dmaengine.h>
+
+#define YUYV_BPP        2
+#define RGB565_BPP      2
+#define RGB24_BPP       3
+#define RGB32_BPP       4
+#define TILE_SIZE       32
+#define YUYV_VRFB_BPP   2
+#define RGB_VRFB_BPP    1
+#define MAX_CID		3
+#define MAC_VRFB_CTXS	4
+#define MAX_VOUT_DEV	2
+#define MAX_OVLS	3
+#define MAX_DISPLAYS	10
+#define MAX_MANAGERS	3
+
+#define QQVGA_WIDTH		160
+#define QQVGA_HEIGHT		120
+
+/* Max Resolution supported by the driver */
+#define VID_MAX_WIDTH		1280	/* Largest width */
+#define VID_MAX_HEIGHT		720	/* Largest height */
+
+/* Minimum requirement is 2x2 for DSS */
+#define VID_MIN_WIDTH		2
+#define VID_MIN_HEIGHT		2
+
+/* 2048 x 2048 is max res supported by OMAP display controller */
+#define MAX_PIXELS_PER_LINE     2048
+
+#define VRFB_TX_TIMEOUT         1000
+#define VRFB_NUM_BUFS		4
+
+/* Max buffer size to be allocated during init */
+#define OMAP_VOUT_MAX_BUF_SIZE (VID_MAX_WIDTH*VID_MAX_HEIGHT*4)
+
+enum dma_channel_state {
+	DMA_CHAN_NOT_ALLOTED,
+	DMA_CHAN_ALLOTED,
+};
+
+/* Enum for Rotation
+ * DSS understands rotation in 0, 1, 2, 3 context
+ * while V4L2 driver understands it as 0, 90, 180, 270
+ */
+enum dss_rotation {
+	dss_rotation_0_degree	= 0,
+	dss_rotation_90_degree	= 1,
+	dss_rotation_180_degree	= 2,
+	dss_rotation_270_degree = 3,
+};
+
+/* Enum for choosing rotation type for vout
+ * DSS2 doesn't understand no rotation as an
+ * option while V4L2 driver doesn't support
+ * rotation in the case where VRFB is not built in
+ * the kernel
+ */
+enum vout_rotaion_type {
+	VOUT_ROT_NONE	= 0,
+	VOUT_ROT_VRFB	= 1,
+};
+
+/*
+ * This structure is used to store the DMA transfer parameters
+ * for VRFB hidden buffer
+ */
+struct vid_vrfb_dma {
+	struct dma_chan *chan;
+	struct dma_interleaved_template *xt;
+
+	int req_status;
+	int tx_status;
+	wait_queue_head_t wait;
+};
+
+struct omapvideo_info {
+	int id;
+	int num_overlays;
+	struct omap_overlay *overlays[MAX_OVLS];
+	enum vout_rotaion_type rotation_type;
+};
+
+struct omap2video_device {
+	struct mutex  mtx;
+
+	int state;
+
+	struct v4l2_device v4l2_dev;
+	struct omap_vout_device *vouts[MAX_VOUT_DEV];
+
+	int num_displays;
+	struct omap_dss_device *displays[MAX_DISPLAYS];
+	int num_overlays;
+	struct omap_overlay *overlays[MAX_OVLS];
+	int num_managers;
+	struct omap_overlay_manager *managers[MAX_MANAGERS];
+};
+
+/* buffer for one video frame */
+struct omap_vout_buffer {
+	/* common v4l buffer stuff -- must be first */
+	struct vb2_v4l2_buffer		vbuf;
+	struct list_head		queue;
+};
+
+static inline struct omap_vout_buffer *vb2_to_omap_vout_buffer(struct vb2_buffer *vb)
+{
+	struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
+
+	return container_of(vbuf, struct omap_vout_buffer, vbuf);
+}
+
+/* per-device data structure */
+struct omap_vout_device {
+
+	struct omapvideo_info vid_info;
+	struct video_device *vfd;
+	struct omap2video_device *vid_dev;
+	struct v4l2_ctrl_handler ctrl_handler;
+	int vid;
+
+	/* allow to reuse previously allocated buffer which is big enough */
+	int buffer_size;
+	enum omap_color_mode dss_mode;
+
+	u32 sequence;
+
+	struct v4l2_pix_format pix;
+	struct v4l2_rect crop;
+	struct v4l2_window win;
+	struct v4l2_framebuffer fbuf;
+
+	/* Lock to protect the shared data structures in ioctl */
+	struct mutex lock;
+
+	enum dss_rotation rotation;
+	bool mirror;
+	int flicker_filter;
+
+	int bpp; /* bytes per pixel */
+	int vrfb_bpp; /* bytes per pixel with respect to VRFB */
+
+	struct vid_vrfb_dma vrfb_dma_tx;
+	unsigned int smsshado_phy_addr[MAC_VRFB_CTXS];
+	unsigned int smsshado_virt_addr[MAC_VRFB_CTXS];
+	struct vrfb vrfb_context[MAC_VRFB_CTXS];
+	bool vrfb_static_allocation;
+	unsigned int smsshado_size;
+	unsigned char pos;
+
+	int ps, vr_ps, line_length, first_int, field_id;
+	struct omap_vout_buffer *cur_frm, *next_frm;
+	spinlock_t vbq_lock;            /* spinlock for dma_queue */
+	struct list_head dma_queue;
+	dma_addr_t queued_buf_addr[VIDEO_MAX_FRAME];
+	u32 cropped_offset;
+	s32 tv_field1_offset;
+	void *isr_handle;
+	struct vb2_queue vq;
+
+};
+
+/*
+ * Return true if rotation is 90 or 270
+ */
+static inline int is_rotation_90_or_270(const struct omap_vout_device *vout)
+{
+	return (vout->rotation == dss_rotation_90_degree ||
+			vout->rotation == dss_rotation_270_degree);
+}
+
+/*
+ * Return true if rotation is enabled
+ */
+static inline int is_rotation_enabled(const struct omap_vout_device *vout)
+{
+	return vout->rotation || vout->mirror;
+}
+
+/*
+ * Reverse the rotation degree if mirroring is enabled
+ */
+static inline int calc_rotation(const struct omap_vout_device *vout)
+{
+	if (!vout->mirror)
+		return vout->rotation;
+
+	switch (vout->rotation) {
+	case dss_rotation_90_degree:
+		return dss_rotation_270_degree;
+	case dss_rotation_270_degree:
+		return dss_rotation_90_degree;
+	case dss_rotation_180_degree:
+		return dss_rotation_0_degree;
+	default:
+		return dss_rotation_180_degree;
+	}
+}
+
+void omap_vout_free_buffers(struct omap_vout_device *vout);
+#endif	/* ifndef OMAP_VOUTDEF_H */

linux-7.2.3/drivers/media/platform/ti/omap/omap_voutlib.c

@@ -0,0 +1,361 @@
+/*
+ * omap_voutlib.c
+ *
+ * Copyright (C) 2005-2010 Texas Instruments.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ *
+ * Based on the OMAP2 camera driver
+ * Video-for-Linux (Version 2) camera capture driver for
+ * the OMAP24xx camera controller.
+ *
+ * Author: Andy Lowe (source@mvista.com)
+ *
+ * Copyright (C) 2004 MontaVista Software, Inc.
+ * Copyright (C) 2010 Texas Instruments.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/videodev2.h>
+
+#include <linux/dma-mapping.h>
+
+#include <video/omapfb_dss.h>
+
+#include "omap_voutlib.h"
+
+MODULE_AUTHOR("Texas Instruments");
+MODULE_DESCRIPTION("OMAP Video library");
+MODULE_LICENSE("GPL");
+
+/* Return the default overlay cropping rectangle in crop given the image
+ * size in pix and the video display size in fbuf.  The default
+ * cropping rectangle is the largest rectangle no larger than the capture size
+ * that will fit on the display.  The default cropping rectangle is centered in
+ * the image.  All dimensions and offsets are rounded down to even numbers.
+ */
+void omap_vout_default_crop(struct v4l2_pix_format *pix,
+		  struct v4l2_framebuffer *fbuf, struct v4l2_rect *crop)
+{
+	crop->width = (pix->width < fbuf->fmt.width) ?
+		pix->width : fbuf->fmt.width;
+	crop->height = (pix->height < fbuf->fmt.height) ?
+		pix->height : fbuf->fmt.height;
+	crop->width &= ~1;
+	crop->height &= ~1;
+	crop->left = ((pix->width - crop->width) >> 1) & ~1;
+	crop->top = ((pix->height - crop->height) >> 1) & ~1;
+}
+EXPORT_SYMBOL_GPL(omap_vout_default_crop);
+
+/* Given a new render window in new_win, adjust the window to the
+ * nearest supported configuration.  The adjusted window parameters are
+ * returned in new_win.
+ * Returns zero if successful, or -EINVAL if the requested window is
+ * impossible and cannot reasonably be adjusted.
+ */
+int omap_vout_try_window(struct v4l2_framebuffer *fbuf,
+			struct v4l2_window *new_win)
+{
+	struct v4l2_rect try_win;
+
+	/* make a working copy of the new_win rectangle */
+	try_win = new_win->w;
+
+	/* adjust the preview window so it fits on the display by clipping any
+	 * offscreen areas
+	 */
+	if (try_win.left < 0) {
+		try_win.width += try_win.left;
+		try_win.left = 0;
+	}
+	if (try_win.top < 0) {
+		try_win.height += try_win.top;
+		try_win.top = 0;
+	}
+	try_win.width = (try_win.width < fbuf->fmt.width) ?
+		try_win.width : fbuf->fmt.width;
+	try_win.height = (try_win.height < fbuf->fmt.height) ?
+		try_win.height : fbuf->fmt.height;
+	if (try_win.left + try_win.width > fbuf->fmt.width)
+		try_win.width = fbuf->fmt.width - try_win.left;
+	if (try_win.top + try_win.height > fbuf->fmt.height)
+		try_win.height = fbuf->fmt.height - try_win.top;
+	try_win.width &= ~1;
+	try_win.height &= ~1;
+
+	if (try_win.width <= 0 || try_win.height <= 0)
+		return -EINVAL;
+
+	/* We now have a valid preview window, so go with it */
+	new_win->w = try_win;
+	new_win->field = V4L2_FIELD_NONE;
+	new_win->clips = NULL;
+	new_win->clipcount = 0;
+	new_win->bitmap = NULL;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(omap_vout_try_window);
+
+/* Given a new render window in new_win, adjust the window to the
+ * nearest supported configuration.  The image cropping window in crop
+ * will also be adjusted if necessary.  Preference is given to keeping the
+ * window as close to the requested configuration as possible.  If
+ * successful, new_win, vout->win, and crop are updated.
+ * Returns zero if successful, or -EINVAL if the requested preview window is
+ * impossible and cannot reasonably be adjusted.
+ */
+int omap_vout_new_window(struct v4l2_rect *crop,
+		struct v4l2_window *win, struct v4l2_framebuffer *fbuf,
+		struct v4l2_window *new_win)
+{
+	int err;
+
+	err = omap_vout_try_window(fbuf, new_win);
+	if (err)
+		return err;
+
+	/* update our preview window */
+	win->w = new_win->w;
+	win->field = new_win->field;
+	win->chromakey = new_win->chromakey;
+
+	/* Adjust the cropping window to allow for resizing limitation */
+	if (omap_vout_dss_omap24xx()) {
+		/* For 24xx limit is 8x to 1/2x scaling. */
+		if ((crop->height/win->w.height) >= 2)
+			crop->height = win->w.height * 2;
+
+		if ((crop->width/win->w.width) >= 2)
+			crop->width = win->w.width * 2;
+
+		if (crop->width > 768) {
+			/* The OMAP2420 vertical resizing line buffer is 768
+			 * pixels wide. If the cropped image is wider than
+			 * 768 pixels then it cannot be vertically resized.
+			 */
+			if (crop->height != win->w.height)
+				crop->width = 768;
+		}
+	} else if (omap_vout_dss_omap34xx()) {
+		/* For 34xx limit is 8x to 1/4x scaling. */
+		if ((crop->height/win->w.height) >= 4)
+			crop->height = win->w.height * 4;
+
+		if ((crop->width/win->w.width) >= 4)
+			crop->width = win->w.width * 4;
+	}
+	return 0;
+}
+EXPORT_SYMBOL_GPL(omap_vout_new_window);
+
+/* Given a new cropping rectangle in new_crop, adjust the cropping rectangle to
+ * the nearest supported configuration.  The image render window in win will
+ * also be adjusted if necessary.  The preview window is adjusted such that the
+ * horizontal and vertical rescaling ratios stay constant.  If the render
+ * window would fall outside the display boundaries, the cropping rectangle
+ * will also be adjusted to maintain the rescaling ratios.  If successful, crop
+ * and win are updated.
+ * Returns zero if successful, or -EINVAL if the requested cropping rectangle is
+ * impossible and cannot reasonably be adjusted.
+ */
+int omap_vout_new_crop(struct v4l2_pix_format *pix,
+	      struct v4l2_rect *crop, struct v4l2_window *win,
+	      struct v4l2_framebuffer *fbuf, const struct v4l2_rect *new_crop)
+{
+	struct v4l2_rect try_crop;
+	unsigned long vresize, hresize;
+
+	/* make a working copy of the new_crop rectangle */
+	try_crop = *new_crop;
+
+	/* adjust the cropping rectangle so it fits in the image */
+	if (try_crop.left < 0) {
+		try_crop.width += try_crop.left;
+		try_crop.left = 0;
+	}
+	if (try_crop.top < 0) {
+		try_crop.height += try_crop.top;
+		try_crop.top = 0;
+	}
+	try_crop.width = (try_crop.width < pix->width) ?
+		try_crop.width : pix->width;
+	try_crop.height = (try_crop.height < pix->height) ?
+		try_crop.height : pix->height;
+	if (try_crop.left + try_crop.width > pix->width)
+		try_crop.width = pix->width - try_crop.left;
+	if (try_crop.top + try_crop.height > pix->height)
+		try_crop.height = pix->height - try_crop.top;
+
+	try_crop.width &= ~1;
+	try_crop.height &= ~1;
+
+	if (try_crop.width <= 0 || try_crop.height <= 0)
+		return -EINVAL;
+
+	if (omap_vout_dss_omap24xx()) {
+		if (try_crop.height != win->w.height) {
+			/* If we're resizing vertically, we can't support a
+			 * crop width wider than 768 pixels.
+			 */
+			if (try_crop.width > 768)
+				try_crop.width = 768;
+		}
+	}
+	/* vertical resizing */
+	vresize = (1024 * try_crop.height) / win->w.height;
+	if (omap_vout_dss_omap24xx() && (vresize > 2048))
+		vresize = 2048;
+	else if (omap_vout_dss_omap34xx() && (vresize > 4096))
+		vresize = 4096;
+
+	win->w.height = ((1024 * try_crop.height) / vresize) & ~1;
+	if (win->w.height == 0)
+		win->w.height = 2;
+	if (win->w.height + win->w.top > fbuf->fmt.height) {
+		/* We made the preview window extend below the bottom of the
+		 * display, so clip it to the display boundary and resize the
+		 * cropping height to maintain the vertical resizing ratio.
+		 */
+		win->w.height = (fbuf->fmt.height - win->w.top) & ~1;
+		if (try_crop.height == 0)
+			try_crop.height = 2;
+	}
+	/* horizontal resizing */
+	hresize = (1024 * try_crop.width) / win->w.width;
+	if (omap_vout_dss_omap24xx() && (hresize > 2048))
+		hresize = 2048;
+	else if (omap_vout_dss_omap34xx() && (hresize > 4096))
+		hresize = 4096;
+
+	win->w.width = ((1024 * try_crop.width) / hresize) & ~1;
+	if (win->w.width == 0)
+		win->w.width = 2;
+	if (win->w.width + win->w.left > fbuf->fmt.width) {
+		/* We made the preview window extend past the right side of the
+		 * display, so clip it to the display boundary and resize the
+		 * cropping width to maintain the horizontal resizing ratio.
+		 */
+		win->w.width = (fbuf->fmt.width - win->w.left) & ~1;
+		if (try_crop.width == 0)
+			try_crop.width = 2;
+	}
+	if (omap_vout_dss_omap24xx()) {
+		if ((try_crop.height/win->w.height) >= 2)
+			try_crop.height = win->w.height * 2;
+
+		if ((try_crop.width/win->w.width) >= 2)
+			try_crop.width = win->w.width * 2;
+
+		if (try_crop.width > 768) {
+			/* The OMAP2420 vertical resizing line buffer is
+			 * 768 pixels wide.  If the cropped image is wider
+			 * than 768 pixels then it cannot be vertically resized.
+			 */
+			if (try_crop.height != win->w.height)
+				try_crop.width = 768;
+		}
+	} else if (omap_vout_dss_omap34xx()) {
+		if ((try_crop.height/win->w.height) >= 4)
+			try_crop.height = win->w.height * 4;
+
+		if ((try_crop.width/win->w.width) >= 4)
+			try_crop.width = win->w.width * 4;
+	}
+	/* update our cropping rectangle and we're done */
+	*crop = try_crop;
+	return 0;
+}
+EXPORT_SYMBOL_GPL(omap_vout_new_crop);
+
+/* Given a new format in pix and fbuf,  crop and win
+ * structures are initialized to default values. crop
+ * is initialized to the largest window size that will fit on the display.  The
+ * crop window is centered in the image. win is initialized to
+ * the same size as crop and is centered on the display.
+ * All sizes and offsets are constrained to be even numbers.
+ */
+void omap_vout_new_format(struct v4l2_pix_format *pix,
+		struct v4l2_framebuffer *fbuf, struct v4l2_rect *crop,
+		struct v4l2_window *win)
+{
+	/* crop defines the preview source window in the image capture
+	 * buffer
+	 */
+	omap_vout_default_crop(pix, fbuf, crop);
+
+	/* win defines the preview target window on the display */
+	win->w.width = crop->width;
+	win->w.height = crop->height;
+	win->w.left = ((fbuf->fmt.width - win->w.width) >> 1) & ~1;
+	win->w.top = ((fbuf->fmt.height - win->w.height) >> 1) & ~1;
+}
+EXPORT_SYMBOL_GPL(omap_vout_new_format);
+
+/*
+ * Allocate buffers
+ */
+unsigned long omap_vout_alloc_buffer(u32 buf_size, u32 *phys_addr)
+{
+	u32 order, size;
+	unsigned long virt_addr, addr;
+
+	size = PAGE_ALIGN(buf_size);
+	order = get_order(size);
+	virt_addr = __get_free_pages(GFP_KERNEL, order);
+	addr = virt_addr;
+
+	if (virt_addr) {
+		while (size > 0) {
+			SetPageReserved(virt_to_page((void *)addr));
+			addr += PAGE_SIZE;
+			size -= PAGE_SIZE;
+		}
+	}
+	*phys_addr = (u32) virt_to_phys((void *) virt_addr);
+	return virt_addr;
+}
+
+/*
+ * Free buffers
+ */
+void omap_vout_free_buffer(unsigned long virtaddr, u32 buf_size)
+{
+	u32 order, size;
+	unsigned long addr = virtaddr;
+
+	size = PAGE_ALIGN(buf_size);
+	order = get_order(size);
+
+	while (size > 0) {
+		ClearPageReserved(virt_to_page((void *)addr));
+		addr += PAGE_SIZE;
+		size -= PAGE_SIZE;
+	}
+	free_pages((unsigned long) virtaddr, order);
+}
+
+bool omap_vout_dss_omap24xx(void)
+{
+	return omapdss_get_version() == OMAPDSS_VER_OMAP24xx;
+}
+
+bool omap_vout_dss_omap34xx(void)
+{
+	switch (omapdss_get_version()) {
+	case OMAPDSS_VER_OMAP34xx_ES1:
+	case OMAPDSS_VER_OMAP34xx_ES3:
+	case OMAPDSS_VER_OMAP3630:
+	case OMAPDSS_VER_AM35xx:
+		return true;
+	default:
+		return false;
+	}
+}

linux-7.2.3/drivers/media/platform/ti/omap/omap_voutlib.h

@@ -0,0 +1,39 @@
+/*
+ * omap_voutlib.h
+ *
+ * Copyright (C) 2010 Texas Instruments.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ *
+ */
+
+#ifndef OMAP_VOUTLIB_H
+#define OMAP_VOUTLIB_H
+
+void omap_vout_default_crop(struct v4l2_pix_format *pix,
+		struct v4l2_framebuffer *fbuf, struct v4l2_rect *crop);
+
+int omap_vout_new_crop(struct v4l2_pix_format *pix,
+		struct v4l2_rect *crop, struct v4l2_window *win,
+		struct v4l2_framebuffer *fbuf,
+		const struct v4l2_rect *new_crop);
+
+int omap_vout_try_window(struct v4l2_framebuffer *fbuf,
+		struct v4l2_window *new_win);
+
+int omap_vout_new_window(struct v4l2_rect *crop,
+		struct v4l2_window *win, struct v4l2_framebuffer *fbuf,
+		struct v4l2_window *new_win);
+
+void omap_vout_new_format(struct v4l2_pix_format *pix,
+		struct v4l2_framebuffer *fbuf, struct v4l2_rect *crop,
+		struct v4l2_window *win);
+unsigned long omap_vout_alloc_buffer(u32 buf_size, u32 *phys_addr);
+void omap_vout_free_buffer(unsigned long virtaddr, u32 buf_size);
+
+bool omap_vout_dss_omap24xx(void);
+bool omap_vout_dss_omap34xx(void);
+#endif	/* #ifndef OMAP_VOUTLIB_H */
+

linux-7.2.3/drivers/media/platform/ti/omap3isp/Kconfig

@@ -0,0 +1,21 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config VIDEO_OMAP3
+	tristate "OMAP 3 Camera support"
+	depends on V4L_PLATFORM_DRIVERS
+	depends on VIDEO_DEV && I2C
+	depends on (ARCH_OMAP3 && OMAP_IOMMU) || COMPILE_TEST
+	depends on COMMON_CLK && OF
+	select ARM_DMA_USE_IOMMU if OMAP_IOMMU
+	select MEDIA_CONTROLLER
+	select VIDEO_V4L2_SUBDEV_API
+	select VIDEOBUF2_DMA_CONTIG
+	select MFD_SYSCON
+	select V4L2_FWNODE
+	help
+	  Driver for an OMAP 3 camera controller.
+
+config VIDEO_OMAP3_DEBUG
+	bool "OMAP 3 Camera debug messages"
+	depends on VIDEO_OMAP3
+	help
+	  Enable debug messages on OMAP 3 camera controller driver.

linux-7.2.3/drivers/media/platform/ti/omap3isp/Makefile

@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0
+# Makefile for OMAP3 ISP driver
+
+ccflags-$(CONFIG_VIDEO_OMAP3_DEBUG) += -DDEBUG
+
+omap3-isp-objs += \
+	isp.o ispvideo.o \
+	ispcsiphy.o ispccp2.o ispcsi2.o \
+	ispccdc.o isppreview.o ispresizer.o \
+	ispstat.o isph3a_aewb.o isph3a_af.o isphist.o
+
+obj-$(CONFIG_VIDEO_OMAP3) += omap3-isp.o

linux-7.2.3/drivers/media/platform/ti/omap3isp/cfa_coef_table.h

@@ -0,0 +1,48 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * cfa_coef_table.h
+ *
+ * TI OMAP3 ISP - CFA coefficients table
+ *
+ * Copyright (C) 2009-2010 Nokia Corporation
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+{ 244, 0, 247,   0,  12,  27,  36, 247, 250,   0,  27,   0,   4, 250,  12, 244,
+248,   0,   0,   0,   0,  40,   0,   0, 244,  12, 250,   4,   0,  27,   0, 250,
+247,  36,  27,  12,   0, 247,   0, 244,   0,   0,  40,   0,   0,   0,   0, 248,
+244,   0, 247,   0,  12,  27,  36, 247, 250,   0,  27,   0,   4, 250,  12, 244,
+248,   0,   0,   0,   0,  40,   0,   0, 244,  12, 250,   4,   0,  27,   0, 250,
+247,  36,  27,  12,   0, 247,   0, 244,   0,   0,  40,   0,   0,   0,   0, 248,
+244,   0, 247,   0,  12,  27,  36, 247, 250,   0,  27,   0,   4, 250,  12, 244,
+248,   0,   0,   0,   0,  40,   0,   0, 244,  12, 250,   4,   0,  27,   0, 250,
+247,  36,  27,  12,   0, 247,   0, 244,   0,   0,  40,   0,   0,   0,   0, 248 },
+{ 0, 247,   0, 244, 247,  36,  27,  12,   0,  27,   0, 250, 244,  12, 250,   4,
+  0,   0,   0, 248,   0,   0,  40,   0,   4, 250,  12, 244, 250,   0,  27,   0,
+ 12,  27,  36, 247, 244,   0, 247,   0,   0,  40,   0,   0, 248,   0,   0,   0,
+  0, 247,   0, 244, 247,  36,  27,  12,   0,  27,   0, 250, 244,  12, 250,   4,
+  0,   0,   0, 248,   0,   0,  40,   0,   4, 250,  12, 244, 250,   0,  27,   0,
+ 12,  27,  36, 247, 244,   0, 247,   0,   0,  40,   0,   0, 248,   0,   0,   0,
+  0, 247,   0, 244, 247,  36,  27,  12,   0,  27,   0, 250, 244,  12, 250,   4,
+  0,   0,   0, 248,   0,   0,  40,   0,   4, 250,  12, 244, 250,   0,  27,   0,
+ 12,  27,  36, 247, 244,   0, 247,   0,   0,  40,   0,   0, 248,   0,   0,   0 },
+{ 4, 250,  12, 244, 250,   0,  27,   0,  12,  27,  36, 247, 244,   0, 247,   0,
+  0,   0,   0, 248,   0,   0,  40,   0,   0, 247,   0, 244, 247,  36,  27,  12,
+  0,  27,   0, 250, 244,  12, 250,   4,   0,  40,   0,   0, 248,   0,   0,   0,
+  4, 250,  12, 244, 250,   0,  27,   0,  12,  27,  36, 247, 244,   0, 247,   0,
+  0,   0,   0, 248,   0,   0,  40,   0,   0, 247,   0, 244, 247,  36,  27,  12,
+  0,  27,   0, 250, 244,  12, 250,   4,   0,  40,   0,   0, 248,   0,   0,   0,
+  4, 250,  12, 244, 250,   0,  27,   0,  12,  27,  36, 247, 244,   0, 247,   0,
+  0,   0,   0, 248,   0,   0,  40,   0,   0, 247,   0, 244, 247,  36,  27,  12,
+  0,  27,   0, 250, 244,  12, 250,   4,   0,  40,   0,   0, 248,   0,   0,   0 },
+{ 244,12, 250,   4,   0,  27,   0, 250, 247,  36,  27,  12,   0, 247,   0, 244,
+248,   0,   0,   0,   0,  40,   0,   0, 244,   0, 247,   0,  12,  27,  36, 247,
+250,   0,  27,   0,   4, 250,  12, 244,   0,   0,  40,   0,   0,   0,   0, 248,
+244,  12, 250,   4,   0,  27,   0, 250, 247,  36,  27,  12,   0, 247,   0, 244,
+248,   0,   0,   0,   0,  40,   0,   0, 244,   0, 247,   0,  12,  27,  36, 247,
+250,   0,  27,   0,   4, 250,  12, 244,   0,   0,  40,   0,   0,   0,   0, 248,
+244,  12, 250,   4,   0,  27,   0, 250, 247,  36,  27,  12,   0, 247,   0, 244,
+248,   0,   0,   0,   0,  40,   0,   0, 244,   0, 247,   0,  12,  27,  36, 247,
+250,   0,  27,   0,   4, 250,  12, 244,   0,   0,  40,   0,   0,   0,   0, 248 },

linux-7.2.3/drivers/media/platform/ti/omap3isp/gamma_table.h

@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * gamma_table.h
+ *
+ * TI OMAP3 ISP - Default gamma table for all components
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+  0,   0,   1,   2,   3,   3,   4,   5,   6,   8,  10,  12,  14,  16,  18,  20,
+ 22,  23,  25,  26,  28,  29,  31,  32,  34,  35,  36,  37,  39,  40,  41,  42,
+ 43,  44,  45,  46,  47,  48,  49,  50,  51,  52,  52,  53,  54,  55,  56,  57,
+ 58,  59,  60,  61,  62,  63,  63,  64,  65,  66,  66,  67,  68,  69,  69,  70,
+ 71,  72,  72,  73,  74,  75,  75,  76,  77,  78,  78,  79,  80,  81,  81,  82,
+ 83,  84,  84,  85,  86,  87,  88,  88,  89,  90,  91,  91,  92,  93,  94,  94,
+ 95,  96,  97,  97,  98,  98,  99,  99, 100, 100, 101, 101, 102, 103, 104, 104,
+105, 106, 107, 108, 108, 109, 110, 111, 111, 112, 113, 114, 114, 115, 116, 117,
+117, 118, 119, 119, 120, 120, 121, 121, 122, 122, 123, 123, 124, 124, 125, 125,
+126, 126, 127, 127, 128, 128, 129, 129, 130, 130, 131, 131, 132, 132, 133, 133,
+134, 134, 135, 135, 136, 136, 137, 137, 138, 138, 139, 139, 140, 140, 141, 141,
+142, 142, 143, 143, 144, 144, 145, 145, 146, 146, 147, 147, 148, 148, 149, 149,
+150, 150, 151, 151, 152, 152, 153, 153, 153, 153, 154, 154, 154, 154, 155, 155,
+156, 156, 157, 157, 158, 158, 158, 159, 159, 159, 160, 160, 160, 161, 161, 162,
+162, 163, 163, 164, 164, 164, 164, 165, 165, 165, 165, 166, 166, 167, 167, 168,
+168, 169, 169, 170, 170, 170, 170, 171, 171, 171, 171, 172, 172, 173, 173, 174,
+174, 175, 175, 176, 176, 176, 176, 177, 177, 177, 177, 178, 178, 178, 178, 179,
+179, 179, 179, 180, 180, 180, 180, 181, 181, 181, 181, 182, 182, 182, 182, 183,
+183, 183, 183, 184, 184, 184, 184, 185, 185, 185, 185, 186, 186, 186, 186, 187,
+187, 187, 187, 188, 188, 188, 188, 189, 189, 189, 189, 190, 190, 190, 190, 191,
+191, 191, 191, 192, 192, 192, 192, 193, 193, 193, 193, 194, 194, 194, 194, 195,
+195, 195, 195, 196, 196, 196, 196, 197, 197, 197, 197, 198, 198, 198, 198, 199,
+199, 199, 199, 200, 200, 200, 200, 201, 201, 201, 201, 202, 202, 202, 203, 203,
+203, 203, 204, 204, 204, 204, 205, 205, 205, 205, 206, 206, 206, 206, 207, 207,
+207, 207, 208, 208, 208, 208, 209, 209, 209, 209, 210, 210, 210, 210, 210, 210,
+210, 210, 210, 210, 210, 210, 211, 211, 211, 211, 211, 211, 211, 211, 211, 211,
+211, 212, 212, 212, 212, 213, 213, 213, 213, 213, 213, 213, 213, 213, 213, 213,
+213, 214, 214, 214, 214, 215, 215, 215, 215, 215, 215, 215, 215, 215, 215, 215,
+216, 216, 216, 216, 217, 217, 217, 217, 218, 218, 218, 218, 219, 219, 219, 219,
+219, 219, 219, 219, 219, 219, 219, 219, 220, 220, 220, 220, 221, 221, 221, 221,
+221, 221, 221, 221, 221, 221, 221, 222, 222, 222, 222, 223, 223, 223, 223, 223,
+223, 223, 223, 223, 223, 223, 223, 224, 224, 224, 224, 225, 225, 225, 225, 225,
+225, 225, 225, 225, 225, 225, 225, 225, 225, 225, 225, 225, 225, 225, 226, 226,
+226, 226, 227, 227, 227, 227, 227, 227, 227, 227, 227, 227, 227, 227, 228, 228,
+228, 229, 229, 229, 229, 229, 229, 229, 229, 229, 229, 229, 229, 230, 230, 230,
+230, 231, 231, 231, 231, 231, 231, 231, 231, 231, 231, 231, 231, 232, 232, 232,
+232, 232, 232, 232, 232, 232, 232, 232, 232, 232, 232, 232, 232, 232, 232, 232,
+233, 233, 233, 233, 234, 234, 234, 234, 234, 234, 234, 234, 234, 234, 234, 235,
+235, 235, 235, 236, 236, 236, 236, 236, 236, 236, 236, 236, 236, 236, 236, 236,
+236, 236, 236, 236, 236, 236, 237, 237, 237, 237, 238, 238, 238, 238, 238, 238,
+238, 238, 238, 238, 238, 238, 238, 238, 238, 238, 238, 238, 238, 238, 238, 238,
+238, 238, 238, 238, 238, 239, 239, 239, 239, 240, 240, 240, 240, 240, 240, 240,
+240, 240, 240, 240, 240, 240, 240, 240, 240, 240, 240, 240, 240, 240, 240, 240,
+240, 240, 240, 240, 241, 241, 241, 241, 242, 242, 242, 242, 242, 242, 242, 242,
+242, 242, 242, 242, 242, 242, 242, 242, 242, 242, 242, 242, 242, 242, 242, 242,
+242, 242, 243, 243, 243, 243, 244, 244, 244, 244, 244, 244, 244, 244, 244, 244,
+244, 244, 244, 244, 244, 244, 244, 244, 244, 244, 244, 244, 244, 244, 244, 244,
+244, 245, 245, 245, 245, 246, 246, 246, 246, 246, 246, 246, 246, 246, 246, 246,
+246, 246, 246, 246, 246, 246, 246, 246, 246, 246, 246, 246, 246, 246, 246, 246,
+246, 246, 246, 246, 246, 246, 246, 247, 247, 247, 247, 248, 248, 248, 248, 248,
+248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248, 248,
+248, 248, 248, 248, 248, 248, 249, 249, 249, 249, 250, 250, 250, 250, 250, 250,
+250, 250, 250, 250, 250, 250, 250, 250, 250, 250, 250, 250, 250, 250, 250, 250,
+250, 250, 250, 250, 250, 250, 250, 250, 250, 250, 250, 250, 250, 250, 250, 250,
+250, 250, 250, 250, 251, 251, 251, 251, 252, 252, 252, 252, 252, 252, 252, 252,
+252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252,
+252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252,
+252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252, 252,
+252, 252, 252, 252, 252, 252, 252, 252, 253, 253, 253, 253, 253, 253, 253, 253,
+253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253,
+253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253,
+253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253, 253,
+253, 254, 254, 254, 254, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255,
+255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255,

linux-7.2.3/drivers/media/platform/ti/omap3isp/isp.h

@@ -0,0 +1,367 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * isp.h
+ *
+ * TI OMAP3 ISP - Core
+ *
+ * Copyright (C) 2009-2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#ifndef OMAP3_ISP_CORE_H
+#define OMAP3_ISP_CORE_H
+
+#include <media/media-entity.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-device.h>
+#include <linux/clk-provider.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/wait.h>
+
+#include "omap3isp.h"
+#include "ispstat.h"
+#include "ispccdc.h"
+#include "ispreg.h"
+#include "ispresizer.h"
+#include "isppreview.h"
+#include "ispcsiphy.h"
+#include "ispcsi2.h"
+#include "ispccp2.h"
+
+#define ISP_TOK_TERM		0xFFFFFFFF	/*
+						 * terminating token for ISP
+						 * modules reg list
+						 */
+#define to_isp_device(ptr_module)				\
+	container_of(ptr_module, struct isp_device, isp_##ptr_module)
+#define to_device(ptr_module)						\
+	(to_isp_device(ptr_module)->dev)
+
+enum isp_mem_resources {
+	OMAP3_ISP_IOMEM_MAIN,
+	OMAP3_ISP_IOMEM_CCP2,
+	OMAP3_ISP_IOMEM_CCDC,
+	OMAP3_ISP_IOMEM_HIST,
+	OMAP3_ISP_IOMEM_H3A,
+	OMAP3_ISP_IOMEM_PREV,
+	OMAP3_ISP_IOMEM_RESZ,
+	OMAP3_ISP_IOMEM_SBL,
+	OMAP3_ISP_IOMEM_CSI2A_REGS1,
+	OMAP3_ISP_IOMEM_CSIPHY2,
+	OMAP3_ISP_IOMEM_CSI2A_REGS2,
+	OMAP3_ISP_IOMEM_CSI2C_REGS1,
+	OMAP3_ISP_IOMEM_CSIPHY1,
+	OMAP3_ISP_IOMEM_CSI2C_REGS2,
+	OMAP3_ISP_IOMEM_LAST
+};
+
+enum isp_sbl_resource {
+	OMAP3_ISP_SBL_CSI1_READ		= 0x1,
+	OMAP3_ISP_SBL_CSI1_WRITE	= 0x2,
+	OMAP3_ISP_SBL_CSI2A_WRITE	= 0x4,
+	OMAP3_ISP_SBL_CSI2C_WRITE	= 0x8,
+	OMAP3_ISP_SBL_CCDC_LSC_READ	= 0x10,
+	OMAP3_ISP_SBL_CCDC_WRITE	= 0x20,
+	OMAP3_ISP_SBL_PREVIEW_READ	= 0x40,
+	OMAP3_ISP_SBL_PREVIEW_WRITE	= 0x80,
+	OMAP3_ISP_SBL_RESIZER_READ	= 0x100,
+	OMAP3_ISP_SBL_RESIZER_WRITE	= 0x200,
+};
+
+enum isp_subclk_resource {
+	OMAP3_ISP_SUBCLK_CCDC		= (1 << 0),
+	OMAP3_ISP_SUBCLK_AEWB		= (1 << 1),
+	OMAP3_ISP_SUBCLK_AF		= (1 << 2),
+	OMAP3_ISP_SUBCLK_HIST		= (1 << 3),
+	OMAP3_ISP_SUBCLK_PREVIEW	= (1 << 4),
+	OMAP3_ISP_SUBCLK_RESIZER	= (1 << 5),
+};
+
+/* ISP: OMAP 34xx ES 1.0 */
+#define ISP_REVISION_1_0		0x10
+/* ISP2: OMAP 34xx ES 2.0, 2.1 and 3.0 */
+#define ISP_REVISION_2_0		0x20
+/* ISP2P: OMAP 36xx */
+#define ISP_REVISION_15_0		0xF0
+
+#define ISP_PHY_TYPE_3430		0
+#define ISP_PHY_TYPE_3630		1
+
+struct regmap;
+
+/*
+ * struct isp_res_mapping - Map ISP io resources to ISP revision.
+ * @isp_rev: ISP_REVISION_x_x
+ * @offset: register offsets of various ISP sub-blocks
+ * @phy_type: ISP_PHY_TYPE_{3430,3630}
+ */
+struct isp_res_mapping {
+	u32 isp_rev;
+	u32 offset[OMAP3_ISP_IOMEM_LAST];
+	u32 phy_type;
+};
+
+/*
+ * struct isp_reg - Structure for ISP register values.
+ * @reg: 32-bit Register address.
+ * @val: 32-bit Register value.
+ */
+struct isp_reg {
+	enum isp_mem_resources mmio_range;
+	u32 reg;
+	u32 val;
+};
+
+enum isp_xclk_id {
+	ISP_XCLK_A,
+	ISP_XCLK_B,
+};
+
+struct isp_xclk {
+	struct isp_device *isp;
+	struct clk_hw hw;
+	struct clk *clk;
+	enum isp_xclk_id id;
+
+	spinlock_t lock;	/* Protects enabled and divider */
+	bool enabled;
+	unsigned int divider;
+};
+
+/*
+ * struct isp_device - ISP device structure.
+ * @dev: Device pointer specific to the OMAP3 ISP.
+ * @revision: Stores current ISP module revision.
+ * @irq_num: Currently used IRQ number.
+ * @mmio_base: Array with kernel base addresses for ioremapped ISP register
+ *             regions.
+ * @mmio_hist_base_phys: Physical L4 bus address for ISP hist block register
+ *			 region.
+ * @syscon: Regmap for the syscon register space
+ * @syscon_offset: Offset of the CSIPHY control register in syscon
+ * @phy_type: ISP_PHY_TYPE_{3430,3630}
+ * @mapping: IOMMU mapping
+ * @stat_lock: Spinlock for handling statistics
+ * @isp_mutex: Mutex for serializing requests to ISP.
+ * @stop_failure: Indicates that an entity failed to stop.
+ * @crashed: Crashed ent_enum
+ * @has_context: Context has been saved at least once and can be restored.
+ * @ref_count: Reference count for handling multiple ISP requests.
+ * @cam_ick: Pointer to camera interface clock structure.
+ * @cam_mclk: Pointer to camera functional clock structure.
+ * @csi2_fck: Pointer to camera CSI2 complexIO clock structure.
+ * @l3_ick: Pointer to OMAP3 L3 bus interface clock.
+ * @xclks: External clocks provided by the ISP
+ * @irq: Currently attached ISP ISR callbacks information structure.
+ * @isp_af: Pointer to current settings for ISP AutoFocus SCM.
+ * @isp_hist: Pointer to current settings for ISP Histogram SCM.
+ * @isp_h3a: Pointer to current settings for ISP Auto Exposure and
+ *           White Balance SCM.
+ * @isp_res: Pointer to current settings for ISP Resizer.
+ * @isp_prev: Pointer to current settings for ISP Preview.
+ * @isp_ccdc: Pointer to current settings for ISP CCDC.
+ * @platform_cb: ISP driver callback function pointers for platform code
+ *
+ * This structure is used to store the OMAP ISP Information.
+ */
+struct isp_device {
+	struct v4l2_device v4l2_dev;
+	struct v4l2_async_notifier notifier;
+	struct media_device media_dev;
+	struct device *dev;
+	u32 revision;
+
+	/* platform HW resources */
+	unsigned int irq_num;
+
+	void __iomem *mmio_base[OMAP3_ISP_IOMEM_LAST];
+	unsigned long mmio_hist_base_phys;
+	struct regmap *syscon;
+	u32 syscon_offset;
+	u32 phy_type;
+
+	struct dma_iommu_mapping *mapping;
+
+	/* ISP Obj */
+	spinlock_t stat_lock;	/* common lock for statistic drivers */
+	struct mutex isp_mutex;	/* For handling ref_count field */
+	bool stop_failure;
+	struct media_entity_enum crashed;
+	int has_context;
+	int ref_count;
+	unsigned int autoidle;
+#define ISP_CLK_CAM_ICK		0
+#define ISP_CLK_CAM_MCLK	1
+#define ISP_CLK_CSI2_FCK	2
+#define ISP_CLK_L3_ICK		3
+	struct clk *clock[4];
+	struct isp_xclk xclks[2];
+
+	/* ISP modules */
+	struct ispstat isp_af;
+	struct ispstat isp_aewb;
+	struct ispstat isp_hist;
+	struct isp_res_device isp_res;
+	struct isp_prev_device isp_prev;
+	struct isp_ccdc_device isp_ccdc;
+	struct isp_csi2_device isp_csi2a;
+	struct isp_csi2_device isp_csi2c;
+	struct isp_ccp2_device isp_ccp2;
+	struct isp_csiphy isp_csiphy1;
+	struct isp_csiphy isp_csiphy2;
+
+	unsigned int sbl_resources;
+	unsigned int subclk_resources;
+};
+
+struct isp_async_subdev {
+	struct v4l2_async_connection asd;
+	struct isp_bus_cfg bus;
+};
+
+static inline struct isp_bus_cfg *
+v4l2_subdev_to_bus_cfg(struct v4l2_subdev *sd)
+{
+	struct v4l2_async_connection *asc;
+
+	asc = v4l2_async_connection_unique(sd);
+	if (!asc)
+		return NULL;
+
+	return &container_of(asc, struct isp_async_subdev, asd)->bus;
+}
+
+#define v4l2_dev_to_isp_device(dev) \
+	container_of(dev, struct isp_device, v4l2_dev)
+
+void omap3isp_hist_dma_done(struct isp_device *isp);
+
+void omap3isp_flush(struct isp_device *isp);
+
+int omap3isp_module_sync_idle(struct media_entity *me, wait_queue_head_t *wait,
+			      atomic_t *stopping);
+
+int omap3isp_module_sync_is_stopping(wait_queue_head_t *wait,
+				     atomic_t *stopping);
+
+int omap3isp_pipeline_set_stream(struct isp_pipeline *pipe,
+				 enum isp_pipeline_stream_state state);
+void omap3isp_pipeline_cancel_stream(struct isp_pipeline *pipe);
+void omap3isp_configure_bridge(struct isp_device *isp,
+			       enum ccdc_input_entity input,
+			       const struct isp_parallel_cfg *buscfg,
+			       unsigned int shift, unsigned int bridge);
+
+struct isp_device *omap3isp_get(struct isp_device *isp);
+void omap3isp_put(struct isp_device *isp);
+
+void omap3isp_sbl_enable(struct isp_device *isp, enum isp_sbl_resource res);
+void omap3isp_sbl_disable(struct isp_device *isp, enum isp_sbl_resource res);
+
+void omap3isp_subclk_enable(struct isp_device *isp,
+			    enum isp_subclk_resource res);
+void omap3isp_subclk_disable(struct isp_device *isp,
+			     enum isp_subclk_resource res);
+
+int omap3isp_register_entities(struct platform_device *pdev,
+			       struct v4l2_device *v4l2_dev);
+void omap3isp_unregister_entities(struct platform_device *pdev);
+
+/*
+ * isp_reg_readl - Read value of an OMAP3 ISP register
+ * @isp: Device pointer specific to the OMAP3 ISP.
+ * @isp_mmio_range: Range to which the register offset refers to.
+ * @reg_offset: Register offset to read from.
+ *
+ * Returns an unsigned 32 bit value with the required register contents.
+ */
+static inline
+u32 isp_reg_readl(struct isp_device *isp, enum isp_mem_resources isp_mmio_range,
+		  u32 reg_offset)
+{
+	return __raw_readl(isp->mmio_base[isp_mmio_range] + reg_offset);
+}
+
+/*
+ * isp_reg_writel - Write value to an OMAP3 ISP register
+ * @isp: Device pointer specific to the OMAP3 ISP.
+ * @reg_value: 32 bit value to write to the register.
+ * @isp_mmio_range: Range to which the register offset refers to.
+ * @reg_offset: Register offset to write into.
+ */
+static inline
+void isp_reg_writel(struct isp_device *isp, u32 reg_value,
+		    enum isp_mem_resources isp_mmio_range, u32 reg_offset)
+{
+	__raw_writel(reg_value, isp->mmio_base[isp_mmio_range] + reg_offset);
+}
+
+/*
+ * isp_reg_clr - Clear individual bits in an OMAP3 ISP register
+ * @isp: Device pointer specific to the OMAP3 ISP.
+ * @mmio_range: Range to which the register offset refers to.
+ * @reg: Register offset to work on.
+ * @clr_bits: 32 bit value which would be cleared in the register.
+ */
+static inline
+void isp_reg_clr(struct isp_device *isp, enum isp_mem_resources mmio_range,
+		 u32 reg, u32 clr_bits)
+{
+	u32 v = isp_reg_readl(isp, mmio_range, reg);
+
+	isp_reg_writel(isp, v & ~clr_bits, mmio_range, reg);
+}
+
+/*
+ * isp_reg_set - Set individual bits in an OMAP3 ISP register
+ * @isp: Device pointer specific to the OMAP3 ISP.
+ * @mmio_range: Range to which the register offset refers to.
+ * @reg: Register offset to work on.
+ * @set_bits: 32 bit value which would be set in the register.
+ */
+static inline
+void isp_reg_set(struct isp_device *isp, enum isp_mem_resources mmio_range,
+		 u32 reg, u32 set_bits)
+{
+	u32 v = isp_reg_readl(isp, mmio_range, reg);
+
+	isp_reg_writel(isp, v | set_bits, mmio_range, reg);
+}
+
+/*
+ * isp_reg_clr_set - Clear and set invidial bits in an OMAP3 ISP register
+ * @isp: Device pointer specific to the OMAP3 ISP.
+ * @mmio_range: Range to which the register offset refers to.
+ * @reg: Register offset to work on.
+ * @clr_bits: 32 bit value which would be cleared in the register.
+ * @set_bits: 32 bit value which would be set in the register.
+ *
+ * The clear operation is done first, and then the set operation.
+ */
+static inline
+void isp_reg_clr_set(struct isp_device *isp, enum isp_mem_resources mmio_range,
+		     u32 reg, u32 clr_bits, u32 set_bits)
+{
+	u32 v = isp_reg_readl(isp, mmio_range, reg);
+
+	isp_reg_writel(isp, (v & ~clr_bits) | set_bits, mmio_range, reg);
+}
+
+static inline enum v4l2_buf_type
+isp_pad_buffer_type(const struct v4l2_subdev *subdev, int pad)
+{
+	if (pad >= subdev->entity.num_pads)
+		return 0;
+
+	if (subdev->entity.pads[pad].flags & MEDIA_PAD_FL_SINK)
+		return V4L2_BUF_TYPE_VIDEO_OUTPUT;
+	else
+		return V4L2_BUF_TYPE_VIDEO_CAPTURE;
+}
+
+#endif	/* OMAP3_ISP_CORE_H */

linux-7.2.3/drivers/media/platform/ti/omap3isp/ispccdc.h

@@ -0,0 +1,174 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * ispccdc.h
+ *
+ * TI OMAP3 ISP - CCDC module
+ *
+ * Copyright (C) 2009-2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#ifndef OMAP3_ISP_CCDC_H
+#define OMAP3_ISP_CCDC_H
+
+#include <linux/omap3isp.h>
+#include <linux/workqueue.h>
+
+#include "ispvideo.h"
+
+enum ccdc_input_entity {
+	CCDC_INPUT_NONE,
+	CCDC_INPUT_PARALLEL,
+	CCDC_INPUT_CSI2A,
+	CCDC_INPUT_CCP2B,
+	CCDC_INPUT_CSI2C
+};
+
+#define CCDC_OUTPUT_MEMORY	(1 << 0)
+#define CCDC_OUTPUT_PREVIEW	(1 << 1)
+#define CCDC_OUTPUT_RESIZER	(1 << 2)
+
+#define	OMAP3ISP_CCDC_NEVENTS	16
+
+struct ispccdc_fpc {
+	void *addr;
+	dma_addr_t dma;
+	unsigned int fpnum;
+};
+
+enum ispccdc_lsc_state {
+	LSC_STATE_STOPPED = 0,
+	LSC_STATE_STOPPING = 1,
+	LSC_STATE_RUNNING = 2,
+	LSC_STATE_RECONFIG = 3,
+};
+
+struct ispccdc_lsc_config_req {
+	struct list_head list;
+	struct omap3isp_ccdc_lsc_config config;
+	unsigned char enable;
+
+	struct {
+		void *addr;
+		dma_addr_t dma;
+		struct sg_table sgt;
+	} table;
+};
+
+/*
+ * ispccdc_lsc - CCDC LSC parameters
+ */
+struct ispccdc_lsc {
+	enum ispccdc_lsc_state state;
+	struct work_struct table_work;
+
+	/* LSC queue of configurations */
+	spinlock_t req_lock;
+	struct ispccdc_lsc_config_req *request;	/* requested configuration */
+	struct ispccdc_lsc_config_req *active;	/* active configuration */
+	struct list_head free_queue;	/* configurations for freeing */
+};
+
+#define CCDC_STOP_NOT_REQUESTED		0x00
+#define CCDC_STOP_REQUEST		0x01
+#define CCDC_STOP_EXECUTED		(0x02 | CCDC_STOP_REQUEST)
+#define CCDC_STOP_CCDC_FINISHED		0x04
+#define CCDC_STOP_LSC_FINISHED		0x08
+#define CCDC_STOP_FINISHED		\
+	(CCDC_STOP_EXECUTED | CCDC_STOP_CCDC_FINISHED | CCDC_STOP_LSC_FINISHED)
+
+#define CCDC_EVENT_VD1			0x10
+#define CCDC_EVENT_VD0			0x20
+#define CCDC_EVENT_LSC_DONE		0x40
+
+/* Sink and source CCDC pads */
+#define CCDC_PAD_SINK			0
+#define CCDC_PAD_SOURCE_OF		1
+#define CCDC_PAD_SOURCE_VP		2
+#define CCDC_PADS_NUM			3
+
+#define CCDC_FIELD_TOP			1
+#define CCDC_FIELD_BOTTOM		2
+#define CCDC_FIELD_BOTH			3
+
+/*
+ * struct isp_ccdc_device - Structure for the CCDC module to store its own
+ *			    information
+ * @subdev: V4L2 subdevice
+ * @pads: Sink and source media entity pads
+ * @formats: Active video formats
+ * @crop: Active crop rectangle on the OF source pad
+ * @input: Active input
+ * @output: Active outputs
+ * @video_out: Output video node
+ * @alaw: A-law compression enabled (1) or disabled (0)
+ * @lpf: Low pass filter enabled (1) or disabled (0)
+ * @obclamp: Optical-black clamp enabled (1) or disabled (0)
+ * @fpc_en: Faulty pixels correction enabled (1) or disabled (0)
+ * @blcomp: Black level compensation configuration
+ * @clamp: Optical-black or digital clamp configuration
+ * @fpc: Faulty pixels correction configuration
+ * @lsc: Lens shading compensation configuration
+ * @update: Bitmask of controls to update during the next interrupt
+ * @shadow_update: Controls update in progress by userspace
+ * @bt656: Whether the input interface uses BT.656 synchronization
+ * @fields: The fields (CCDC_FIELD_*) stored in the current buffer
+ * @underrun: A buffer underrun occurred and a new buffer has been queued
+ * @state: Streaming state
+ * @lock: Serializes shadow_update with interrupt handler
+ * @wait: Wait queue used to stop the module
+ * @stopping: Stopping state
+ * @running: Is the CCDC hardware running
+ * @ioctl_lock: Serializes ioctl calls and LSC requests freeing
+ */
+struct isp_ccdc_device {
+	struct v4l2_subdev subdev;
+	struct media_pad pads[CCDC_PADS_NUM];
+	struct v4l2_mbus_framefmt formats[CCDC_PADS_NUM];
+	struct v4l2_rect crop;
+
+	enum ccdc_input_entity input;
+	unsigned int output;
+	struct isp_video video_out;
+
+	unsigned int alaw:1,
+		     lpf:1,
+		     obclamp:1,
+		     fpc_en:1;
+	struct omap3isp_ccdc_blcomp blcomp;
+	struct omap3isp_ccdc_bclamp clamp;
+	struct ispccdc_fpc fpc;
+	struct ispccdc_lsc lsc;
+	unsigned int update;
+	unsigned int shadow_update;
+
+	bool bt656;
+	unsigned int fields;
+
+	unsigned int underrun:1;
+	enum isp_pipeline_stream_state state;
+	spinlock_t lock;
+	wait_queue_head_t wait;
+	unsigned int stopping;
+	bool running;
+	struct mutex ioctl_lock;
+};
+
+struct isp_device;
+
+int omap3isp_ccdc_init(struct isp_device *isp);
+void omap3isp_ccdc_cleanup(struct isp_device *isp);
+int omap3isp_ccdc_register_entities(struct isp_ccdc_device *ccdc,
+	struct v4l2_device *vdev);
+void omap3isp_ccdc_unregister_entities(struct isp_ccdc_device *ccdc);
+
+int omap3isp_ccdc_busy(struct isp_ccdc_device *isp_ccdc);
+int omap3isp_ccdc_isr(struct isp_ccdc_device *isp_ccdc, u32 events);
+void omap3isp_ccdc_restore_context(struct isp_device *isp);
+void omap3isp_ccdc_max_rate(struct isp_ccdc_device *ccdc,
+	unsigned int *max_rate);
+
+#endif	/* OMAP3_ISP_CCDC_H */

linux-7.2.3/drivers/media/platform/ti/omap3isp/ispccp2.h

@@ -0,0 +1,85 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * ispccp2.h
+ *
+ * TI OMAP3 ISP - CCP2 module
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2010 Texas Instruments, Inc.
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#ifndef OMAP3_ISP_CCP2_H
+#define OMAP3_ISP_CCP2_H
+
+#include <linux/videodev2.h>
+
+struct isp_device;
+struct isp_csiphy;
+
+/* Sink and source ccp2 pads */
+#define CCP2_PAD_SINK			0
+#define CCP2_PAD_SOURCE			1
+#define CCP2_PADS_NUM			2
+
+/* CCP2 input media entity */
+enum ccp2_input_entity {
+	CCP2_INPUT_NONE,
+	CCP2_INPUT_SENSOR,
+	CCP2_INPUT_MEMORY,
+};
+
+/* CCP2 output media entity */
+enum ccp2_output_entity {
+	CCP2_OUTPUT_NONE,
+	CCP2_OUTPUT_CCDC,
+	CCP2_OUTPUT_MEMORY,
+};
+
+
+/* Logical channel configuration */
+struct isp_interface_lcx_config {
+	int crc;
+	u32 data_start;
+	u32 data_size;
+	u32 format;
+};
+
+/* Memory channel configuration */
+struct isp_interface_mem_config {
+	u32 dst_port;
+	u32 vsize_count;
+	u32 hsize_count;
+	u32 src_ofst;
+	u32 dst_ofst;
+};
+
+/* CCP2 device */
+struct isp_ccp2_device {
+	struct v4l2_subdev subdev;
+	struct v4l2_mbus_framefmt formats[CCP2_PADS_NUM];
+	struct media_pad pads[CCP2_PADS_NUM];
+
+	enum ccp2_input_entity input;
+	enum ccp2_output_entity output;
+	struct isp_interface_lcx_config if_cfg;
+	struct isp_interface_mem_config mem_cfg;
+	struct isp_video video_in;
+	struct isp_csiphy *phy;
+	struct regulator *vdds_csib;
+	enum isp_pipeline_stream_state state;
+	wait_queue_head_t wait;
+	atomic_t stopping;
+};
+
+/* Function declarations */
+int omap3isp_ccp2_init(struct isp_device *isp);
+void omap3isp_ccp2_cleanup(struct isp_device *isp);
+int omap3isp_ccp2_register_entities(struct isp_ccp2_device *ccp2,
+			struct v4l2_device *vdev);
+void omap3isp_ccp2_unregister_entities(struct isp_ccp2_device *ccp2);
+void omap3isp_ccp2_isr(struct isp_ccp2_device *ccp2);
+
+#endif	/* OMAP3_ISP_CCP2_H */

linux-7.2.3/drivers/media/platform/ti/omap3isp/ispcsi2.h

@@ -0,0 +1,152 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * ispcsi2.h
+ *
+ * TI OMAP3 ISP - CSI2 module
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#ifndef OMAP3_ISP_CSI2_H
+#define OMAP3_ISP_CSI2_H
+
+#include <linux/types.h>
+#include <linux/videodev2.h>
+
+struct isp_csiphy;
+
+/* This is not an exhaustive list */
+enum isp_csi2_pix_formats {
+	CSI2_PIX_FMT_OTHERS = 0,
+	CSI2_PIX_FMT_YUV422_8BIT = 0x1e,
+	CSI2_PIX_FMT_YUV422_8BIT_VP = 0x9e,
+	CSI2_PIX_FMT_RAW10_EXP16 = 0xab,
+	CSI2_PIX_FMT_RAW10_EXP16_VP = 0x12f,
+	CSI2_PIX_FMT_RAW8 = 0x2a,
+	CSI2_PIX_FMT_RAW8_DPCM10_EXP16 = 0x2aa,
+	CSI2_PIX_FMT_RAW8_DPCM10_VP = 0x32a,
+	CSI2_PIX_FMT_RAW8_VP = 0x12a,
+	CSI2_USERDEF_8BIT_DATA1_DPCM10_VP = 0x340,
+	CSI2_USERDEF_8BIT_DATA1_DPCM10 = 0x2c0,
+	CSI2_USERDEF_8BIT_DATA1 = 0x40,
+};
+
+enum isp_csi2_irqevents {
+	OCP_ERR_IRQ = 0x4000,
+	SHORT_PACKET_IRQ = 0x2000,
+	ECC_CORRECTION_IRQ = 0x1000,
+	ECC_NO_CORRECTION_IRQ = 0x800,
+	COMPLEXIO2_ERR_IRQ = 0x400,
+	COMPLEXIO1_ERR_IRQ = 0x200,
+	FIFO_OVF_IRQ = 0x100,
+	CONTEXT7 = 0x80,
+	CONTEXT6 = 0x40,
+	CONTEXT5 = 0x20,
+	CONTEXT4 = 0x10,
+	CONTEXT3 = 0x8,
+	CONTEXT2 = 0x4,
+	CONTEXT1 = 0x2,
+	CONTEXT0 = 0x1,
+};
+
+enum isp_csi2_ctx_irqevents {
+	CTX_ECC_CORRECTION = 0x100,
+	CTX_LINE_NUMBER = 0x80,
+	CTX_FRAME_NUMBER = 0x40,
+	CTX_CS = 0x20,
+	CTX_LE = 0x8,
+	CTX_LS = 0x4,
+	CTX_FE = 0x2,
+	CTX_FS = 0x1,
+};
+
+enum isp_csi2_frame_mode {
+	ISP_CSI2_FRAME_IMMEDIATE,
+	ISP_CSI2_FRAME_AFTERFEC,
+};
+
+#define ISP_CSI2_MAX_CTX_NUM	7
+
+struct isp_csi2_ctx_cfg {
+	u8 ctxnum;		/* context number 0 - 7 */
+	u8 dpcm_decompress;
+
+	/* Fields in CSI2_CTx_CTRL2 - locked by CSI2_CTx_CTRL1.CTX_EN */
+	u8 virtual_id;
+	u16 format_id;		/* as in CSI2_CTx_CTRL2[9:0] */
+	u8 dpcm_predictor;	/* 1: simple, 0: advanced */
+
+	/* Fields in CSI2_CTx_CTRL1/3 - Shadowed */
+	u16 alpha;
+	u16 data_offset;
+	u32 ping_addr;
+	u32 pong_addr;
+	u8 eof_enabled;
+	u8 eol_enabled;
+	u8 checksum_enabled;
+	u8 enabled;
+};
+
+struct isp_csi2_timing_cfg {
+	u8 ionum;			/* IO1 or IO2 as in CSI2_TIMING */
+	unsigned force_rx_mode:1;
+	unsigned stop_state_16x:1;
+	unsigned stop_state_4x:1;
+	u16 stop_state_counter;
+};
+
+struct isp_csi2_ctrl_cfg {
+	bool vp_clk_enable;
+	bool vp_only_enable;
+	u8 vp_out_ctrl;
+	enum isp_csi2_frame_mode frame_mode;
+	bool ecc_enable;
+	bool if_enable;
+};
+
+#define CSI2_PAD_SINK		0
+#define CSI2_PAD_SOURCE		1
+#define CSI2_PADS_NUM		2
+
+#define CSI2_OUTPUT_CCDC	(1 << 0)
+#define CSI2_OUTPUT_MEMORY	(1 << 1)
+
+struct isp_csi2_device {
+	struct v4l2_subdev subdev;
+	struct media_pad pads[CSI2_PADS_NUM];
+	struct v4l2_mbus_framefmt formats[CSI2_PADS_NUM];
+
+	struct isp_video video_out;
+	struct isp_device *isp;
+
+	u8 available;		/* Is the IP present on the silicon? */
+
+	/* mem resources - enums as defined in enum isp_mem_resources */
+	u8 regs1;
+	u8 regs2;
+
+	u32 output; /* output to CCDC, memory or both? */
+	bool dpcm_decompress;
+	unsigned int frame_skip;
+
+	struct isp_csiphy *phy;
+	struct isp_csi2_ctx_cfg contexts[ISP_CSI2_MAX_CTX_NUM + 1];
+	struct isp_csi2_timing_cfg timing[2];
+	struct isp_csi2_ctrl_cfg ctrl;
+	enum isp_pipeline_stream_state state;
+	wait_queue_head_t wait;
+	atomic_t stopping;
+};
+
+void omap3isp_csi2_isr(struct isp_csi2_device *csi2);
+int omap3isp_csi2_reset(struct isp_csi2_device *csi2);
+int omap3isp_csi2_init(struct isp_device *isp);
+void omap3isp_csi2_cleanup(struct isp_device *isp);
+void omap3isp_csi2_unregister_entities(struct isp_csi2_device *csi2);
+int omap3isp_csi2_register_entities(struct isp_csi2_device *csi2,
+				    struct v4l2_device *vdev);
+#endif	/* OMAP3_ISP_CSI2_H */

linux-7.2.3/drivers/media/platform/ti/omap3isp/ispcsiphy.c

@@ -0,0 +1,365 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * ispcsiphy.c
+ *
+ * TI OMAP3 ISP - CSI PHY module
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+
+#include "isp.h"
+#include "ispreg.h"
+#include "ispcsiphy.h"
+
+static void csiphy_routing_cfg_3630(struct isp_csiphy *phy,
+				    enum isp_interface_type iface,
+				    bool ccp2_strobe)
+{
+	u32 reg;
+	u32 shift, mode;
+
+	regmap_read(phy->isp->syscon, phy->isp->syscon_offset, &reg);
+
+	switch (iface) {
+	default:
+		/* Should not happen in practice, but let's keep the compiler happy. */
+		return;
+	case ISP_INTERFACE_CCP2B_PHY1:
+		reg &= ~OMAP3630_CONTROL_CAMERA_PHY_CTRL_CSI1_RX_SEL_PHY2;
+		shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY1_SHIFT;
+		break;
+	case ISP_INTERFACE_CSI2C_PHY1:
+		shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY1_SHIFT;
+		mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_DPHY;
+		break;
+	case ISP_INTERFACE_CCP2B_PHY2:
+		reg |= OMAP3630_CONTROL_CAMERA_PHY_CTRL_CSI1_RX_SEL_PHY2;
+		shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY2_SHIFT;
+		break;
+	case ISP_INTERFACE_CSI2A_PHY2:
+		shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY2_SHIFT;
+		mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_DPHY;
+		break;
+	}
+
+	/* Select data/clock or data/strobe mode for CCP2 */
+	if (iface == ISP_INTERFACE_CCP2B_PHY1 ||
+	    iface == ISP_INTERFACE_CCP2B_PHY2) {
+		if (ccp2_strobe)
+			mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_CCP2_DATA_STROBE;
+		else
+			mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_CCP2_DATA_CLOCK;
+	}
+
+	reg &= ~(OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_MASK << shift);
+	reg |= mode << shift;
+
+	regmap_write(phy->isp->syscon, phy->isp->syscon_offset, reg);
+}
+
+static void csiphy_routing_cfg_3430(struct isp_csiphy *phy, u32 iface, bool on,
+				    bool ccp2_strobe)
+{
+	u32 csirxfe = OMAP343X_CONTROL_CSIRXFE_PWRDNZ
+		| OMAP343X_CONTROL_CSIRXFE_RESET;
+
+	/* Only the CCP2B on PHY1 is configurable. */
+	if (iface != ISP_INTERFACE_CCP2B_PHY1)
+		return;
+
+	if (!on) {
+		regmap_write(phy->isp->syscon, phy->isp->syscon_offset, 0);
+		return;
+	}
+
+	if (ccp2_strobe)
+		csirxfe |= OMAP343X_CONTROL_CSIRXFE_SELFORM;
+
+	regmap_write(phy->isp->syscon, phy->isp->syscon_offset, csirxfe);
+}
+
+/*
+ * Configure OMAP 3 CSI PHY routing.
+ * @phy: relevant phy device
+ * @iface: ISP_INTERFACE_*
+ * @on: power on or off
+ * @ccp2_strobe: false: data/clock, true: data/strobe
+ *
+ * Note that the underlying routing configuration registers are part of the
+ * control (SCM) register space and part of the CORE power domain on both 3430
+ * and 3630, so they will not hold their contents in off-mode. This isn't an
+ * issue since the MPU power domain is forced on whilst the ISP is in use.
+ */
+static void csiphy_routing_cfg(struct isp_csiphy *phy,
+			       enum isp_interface_type iface, bool on,
+			       bool ccp2_strobe)
+{
+	if (phy->isp->phy_type == ISP_PHY_TYPE_3630 && on)
+		return csiphy_routing_cfg_3630(phy, iface, ccp2_strobe);
+	if (phy->isp->phy_type == ISP_PHY_TYPE_3430)
+		return csiphy_routing_cfg_3430(phy, iface, on, ccp2_strobe);
+}
+
+/*
+ * csiphy_power_autoswitch_enable
+ * @enable: Sets or clears the autoswitch function enable flag.
+ */
+static void csiphy_power_autoswitch_enable(struct isp_csiphy *phy, bool enable)
+{
+	isp_reg_clr_set(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG,
+			ISPCSI2_PHY_CFG_PWR_AUTO,
+			enable ? ISPCSI2_PHY_CFG_PWR_AUTO : 0);
+}
+
+/*
+ * csiphy_set_power
+ * @power: Power state to be set.
+ *
+ * Returns 0 if successful, or -EBUSY if the retry count is exceeded.
+ */
+static int csiphy_set_power(struct isp_csiphy *phy, u32 power)
+{
+	u32 reg;
+	u8 retry_count;
+
+	isp_reg_clr_set(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG,
+			ISPCSI2_PHY_CFG_PWR_CMD_MASK, power);
+
+	retry_count = 0;
+	do {
+		udelay(50);
+		reg = isp_reg_readl(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG) &
+				    ISPCSI2_PHY_CFG_PWR_STATUS_MASK;
+
+		if (reg != power >> 2)
+			retry_count++;
+
+	} while ((reg != power >> 2) && (retry_count < 100));
+
+	if (retry_count == 100) {
+		dev_err(phy->isp->dev, "CSI2 CIO set power failed!\n");
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
+/*
+ * TCLK values are OK at their reset values
+ */
+#define TCLK_TERM	0
+#define TCLK_MISS	1
+#define TCLK_SETTLE	14
+
+static int omap3isp_csiphy_config(struct isp_csiphy *phy)
+{
+	struct isp_pipeline *pipe = to_isp_pipeline(phy->entity);
+	struct isp_bus_cfg *buscfg;
+	struct isp_csiphy_lanes_cfg *lanes;
+	int csi2_ddrclk_khz;
+	unsigned int num_data_lanes, used_lanes = 0;
+	unsigned int i;
+	u32 reg;
+
+	buscfg = v4l2_subdev_to_bus_cfg(pipe->external);
+	if (WARN_ON(!buscfg))
+		return -EPIPE;
+
+	if (buscfg->interface == ISP_INTERFACE_CCP2B_PHY1
+	    || buscfg->interface == ISP_INTERFACE_CCP2B_PHY2) {
+		lanes = &buscfg->bus.ccp2.lanecfg;
+		num_data_lanes = 1;
+	} else {
+		lanes = &buscfg->bus.csi2.lanecfg;
+		num_data_lanes = buscfg->bus.csi2.num_data_lanes;
+	}
+
+	if (num_data_lanes > phy->num_data_lanes)
+		return -EINVAL;
+
+	/* Clock and data lanes verification */
+	for (i = 0; i < num_data_lanes; i++) {
+		if (lanes->data[i].pol > 1 || lanes->data[i].pos > 3)
+			return -EINVAL;
+
+		if (used_lanes & (1 << lanes->data[i].pos))
+			return -EINVAL;
+
+		used_lanes |= 1 << lanes->data[i].pos;
+	}
+
+	if (lanes->clk.pol > 1 || lanes->clk.pos > 3)
+		return -EINVAL;
+
+	if (lanes->clk.pos == 0 || used_lanes & (1 << lanes->clk.pos))
+		return -EINVAL;
+
+	/*
+	 * The PHY configuration is lost in off mode, that's not an
+	 * issue since the MPU power domain is forced on whilst the
+	 * ISP is in use.
+	 */
+	csiphy_routing_cfg(phy, buscfg->interface, true,
+			   buscfg->bus.ccp2.phy_layer);
+
+	/* DPHY timing configuration */
+	/* CSI-2 is DDR and we only count used lanes. */
+	csi2_ddrclk_khz = pipe->external_rate / 1000
+		/ (2 * hweight32(used_lanes)) * pipe->external_width;
+
+	reg = isp_reg_readl(phy->isp, phy->phy_regs, ISPCSIPHY_REG0);
+
+	reg &= ~(ISPCSIPHY_REG0_THS_TERM_MASK |
+		 ISPCSIPHY_REG0_THS_SETTLE_MASK);
+	/* THS_TERM: Programmed value = ceil(12.5 ns/DDRClk period) - 1. */
+	reg |= (DIV_ROUND_UP(25 * csi2_ddrclk_khz, 2000000) - 1)
+		<< ISPCSIPHY_REG0_THS_TERM_SHIFT;
+	/* THS_SETTLE: Programmed value = ceil(90 ns/DDRClk period) + 3. */
+	reg |= (DIV_ROUND_UP(90 * csi2_ddrclk_khz, 1000000) + 3)
+		<< ISPCSIPHY_REG0_THS_SETTLE_SHIFT;
+
+	isp_reg_writel(phy->isp, reg, phy->phy_regs, ISPCSIPHY_REG0);
+
+	reg = isp_reg_readl(phy->isp, phy->phy_regs, ISPCSIPHY_REG1);
+
+	reg &= ~(ISPCSIPHY_REG1_TCLK_TERM_MASK |
+		 ISPCSIPHY_REG1_TCLK_MISS_MASK |
+		 ISPCSIPHY_REG1_TCLK_SETTLE_MASK);
+	reg |= TCLK_TERM << ISPCSIPHY_REG1_TCLK_TERM_SHIFT;
+	reg |= TCLK_MISS << ISPCSIPHY_REG1_TCLK_MISS_SHIFT;
+	reg |= TCLK_SETTLE << ISPCSIPHY_REG1_TCLK_SETTLE_SHIFT;
+
+	isp_reg_writel(phy->isp, reg, phy->phy_regs, ISPCSIPHY_REG1);
+
+	/* DPHY lane configuration */
+	reg = isp_reg_readl(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG);
+
+	for (i = 0; i < num_data_lanes; i++) {
+		reg &= ~(ISPCSI2_PHY_CFG_DATA_POL_MASK(i + 1) |
+			 ISPCSI2_PHY_CFG_DATA_POSITION_MASK(i + 1));
+		reg |= (lanes->data[i].pol <<
+			ISPCSI2_PHY_CFG_DATA_POL_SHIFT(i + 1));
+		reg |= (lanes->data[i].pos <<
+			ISPCSI2_PHY_CFG_DATA_POSITION_SHIFT(i + 1));
+	}
+
+	reg &= ~(ISPCSI2_PHY_CFG_CLOCK_POL_MASK |
+		 ISPCSI2_PHY_CFG_CLOCK_POSITION_MASK);
+	reg |= lanes->clk.pol << ISPCSI2_PHY_CFG_CLOCK_POL_SHIFT;
+	reg |= lanes->clk.pos << ISPCSI2_PHY_CFG_CLOCK_POSITION_SHIFT;
+
+	isp_reg_writel(phy->isp, reg, phy->cfg_regs, ISPCSI2_PHY_CFG);
+
+	return 0;
+}
+
+int omap3isp_csiphy_acquire(struct isp_csiphy *phy, struct media_entity *entity)
+{
+	int rval;
+
+	if (phy->vdd == NULL) {
+		dev_err(phy->isp->dev,
+			"Power regulator for CSI PHY not available\n");
+		return -ENODEV;
+	}
+
+	mutex_lock(&phy->mutex);
+
+	rval = regulator_enable(phy->vdd);
+	if (rval < 0)
+		goto done;
+
+	rval = omap3isp_csi2_reset(phy->csi2);
+	if (rval < 0)
+		goto done;
+
+	phy->entity = entity;
+
+	rval = omap3isp_csiphy_config(phy);
+	if (rval < 0)
+		goto done;
+
+	if (phy->isp->revision == ISP_REVISION_15_0) {
+		rval = csiphy_set_power(phy, ISPCSI2_PHY_CFG_PWR_CMD_ON);
+		if (rval) {
+			regulator_disable(phy->vdd);
+			goto done;
+		}
+
+		csiphy_power_autoswitch_enable(phy, true);
+	}
+done:
+	if (rval < 0)
+		phy->entity = NULL;
+
+	mutex_unlock(&phy->mutex);
+	return rval;
+}
+
+void omap3isp_csiphy_release(struct isp_csiphy *phy)
+{
+	mutex_lock(&phy->mutex);
+	if (phy->entity) {
+		struct isp_pipeline *pipe = to_isp_pipeline(phy->entity);
+		struct isp_bus_cfg *buscfg;
+
+		buscfg = v4l2_subdev_to_bus_cfg(pipe->external);
+		if (WARN_ON(!buscfg)) {
+			mutex_unlock(&phy->mutex);
+			return;
+		}
+
+		csiphy_routing_cfg(phy, buscfg->interface, false,
+				   buscfg->bus.ccp2.phy_layer);
+		if (phy->isp->revision == ISP_REVISION_15_0) {
+			csiphy_power_autoswitch_enable(phy, false);
+			csiphy_set_power(phy, ISPCSI2_PHY_CFG_PWR_CMD_OFF);
+		}
+		regulator_disable(phy->vdd);
+		phy->entity = NULL;
+	}
+	mutex_unlock(&phy->mutex);
+}
+
+/*
+ * omap3isp_csiphy_init - Initialize the CSI PHY frontends
+ */
+int omap3isp_csiphy_init(struct isp_device *isp)
+{
+	struct isp_csiphy *phy1 = &isp->isp_csiphy1;
+	struct isp_csiphy *phy2 = &isp->isp_csiphy2;
+
+	phy2->isp = isp;
+	phy2->csi2 = &isp->isp_csi2a;
+	phy2->num_data_lanes = ISP_CSIPHY2_NUM_DATA_LANES;
+	phy2->cfg_regs = OMAP3_ISP_IOMEM_CSI2A_REGS1;
+	phy2->phy_regs = OMAP3_ISP_IOMEM_CSIPHY2;
+	mutex_init(&phy2->mutex);
+
+	phy1->isp = isp;
+	mutex_init(&phy1->mutex);
+
+	if (isp->revision == ISP_REVISION_15_0) {
+		phy1->csi2 = &isp->isp_csi2c;
+		phy1->num_data_lanes = ISP_CSIPHY1_NUM_DATA_LANES;
+		phy1->cfg_regs = OMAP3_ISP_IOMEM_CSI2C_REGS1;
+		phy1->phy_regs = OMAP3_ISP_IOMEM_CSIPHY1;
+	}
+
+	return 0;
+}
+
+void omap3isp_csiphy_cleanup(struct isp_device *isp)
+{
+	mutex_destroy(&isp->isp_csiphy1.mutex);
+	mutex_destroy(&isp->isp_csiphy2.mutex);
+}

linux-7.2.3/drivers/media/platform/ti/omap3isp/ispcsiphy.h

@@ -0,0 +1,43 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * ispcsiphy.h
+ *
+ * TI OMAP3 ISP - CSI PHY module
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#ifndef OMAP3_ISP_CSI_PHY_H
+#define OMAP3_ISP_CSI_PHY_H
+
+#include "omap3isp.h"
+
+struct isp_csi2_device;
+struct regulator;
+
+struct isp_csiphy {
+	struct isp_device *isp;
+	struct mutex mutex;	/* serialize csiphy configuration */
+	struct isp_csi2_device *csi2;
+	struct regulator *vdd;
+	/* the entity that acquired the phy */
+	struct media_entity *entity;
+
+	/* mem resources - enums as defined in enum isp_mem_resources */
+	unsigned int cfg_regs;
+	unsigned int phy_regs;
+
+	u8 num_data_lanes;	/* number of CSI2 Data Lanes supported */
+};
+
+int omap3isp_csiphy_acquire(struct isp_csiphy *phy,
+			    struct media_entity *entity);
+void omap3isp_csiphy_release(struct isp_csiphy *phy);
+int omap3isp_csiphy_init(struct isp_device *isp);
+void omap3isp_csiphy_cleanup(struct isp_device *isp);
+
+#endif	/* OMAP3_ISP_CSI_PHY_H */

linux-7.2.3/drivers/media/platform/ti/omap3isp/isph3a.h

@@ -0,0 +1,104 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * isph3a.h
+ *
+ * TI OMAP3 ISP - H3A AF module
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: David Cohen <dacohen@gmail.com>
+ *	     Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#ifndef OMAP3_ISP_H3A_H
+#define OMAP3_ISP_H3A_H
+
+#include <linux/omap3isp.h>
+
+/*
+ * ----------
+ * -H3A AEWB-
+ * ----------
+ */
+
+#define AEWB_PACKET_SIZE	16
+#define AEWB_SATURATION_LIMIT	0x3ff
+
+/* Flags for changed registers */
+#define PCR_CHNG		(1 << 0)
+#define AEWWIN1_CHNG		(1 << 1)
+#define AEWINSTART_CHNG		(1 << 2)
+#define AEWINBLK_CHNG		(1 << 3)
+#define AEWSUBWIN_CHNG		(1 << 4)
+#define PRV_WBDGAIN_CHNG	(1 << 5)
+#define PRV_WBGAIN_CHNG		(1 << 6)
+
+/* ISPH3A REGISTERS bits */
+#define ISPH3A_PCR_AF_EN	(1 << 0)
+#define ISPH3A_PCR_AF_ALAW_EN	(1 << 1)
+#define ISPH3A_PCR_AF_MED_EN	(1 << 2)
+#define ISPH3A_PCR_AF_BUSY	(1 << 15)
+#define ISPH3A_PCR_AEW_EN	(1 << 16)
+#define ISPH3A_PCR_AEW_ALAW_EN	(1 << 17)
+#define ISPH3A_PCR_AEW_BUSY	(1 << 18)
+#define ISPH3A_PCR_AEW_MASK	(ISPH3A_PCR_AEW_ALAW_EN | \
+				 ISPH3A_PCR_AEW_AVE2LMT_MASK)
+
+/*
+ * --------
+ * -H3A AF-
+ * --------
+ */
+
+/* Peripheral Revision */
+#define AFPID				0x0
+
+#define AFCOEF_OFFSET			0x00000004	/* COEF base address */
+
+/* PCR fields */
+#define AF_BUSYAF			(1 << 15)
+#define AF_FVMODE			(1 << 14)
+#define AF_RGBPOS			(0x7 << 11)
+#define AF_MED_TH			(0xFF << 3)
+#define AF_MED_EN			(1 << 2)
+#define AF_ALAW_EN			(1 << 1)
+#define AF_EN				(1 << 0)
+#define AF_PCR_MASK			(AF_FVMODE | AF_RGBPOS | AF_MED_TH | \
+					 AF_MED_EN | AF_ALAW_EN)
+
+/* AFPAX1 fields */
+#define AF_PAXW				(0x7F << 16)
+#define AF_PAXH				0x7F
+
+/* AFPAX2 fields */
+#define AF_AFINCV			(0xF << 13)
+#define AF_PAXVC			(0x7F << 6)
+#define AF_PAXHC			0x3F
+
+/* AFPAXSTART fields */
+#define AF_PAXSH			(0xFFF<<16)
+#define AF_PAXSV			0xFFF
+
+/* COEFFICIENT MASK */
+#define AF_COEF_MASK0			0xFFF
+#define AF_COEF_MASK1			(0xFFF<<16)
+
+/* BIT SHIFTS */
+#define AF_RGBPOS_SHIFT			11
+#define AF_MED_TH_SHIFT			3
+#define AF_PAXW_SHIFT			16
+#define AF_LINE_INCR_SHIFT		13
+#define AF_VT_COUNT_SHIFT		6
+#define AF_HZ_START_SHIFT		16
+#define AF_COEF_SHIFT			16
+
+/* Init and cleanup functions */
+int omap3isp_h3a_aewb_init(struct isp_device *isp);
+int omap3isp_h3a_af_init(struct isp_device *isp);
+
+void omap3isp_h3a_aewb_cleanup(struct isp_device *isp);
+void omap3isp_h3a_af_cleanup(struct isp_device *isp);
+
+#endif /* OMAP3_ISP_H3A_H */

linux-7.2.3/drivers/media/platform/ti/omap3isp/isph3a_aewb.c

@@ -0,0 +1,350 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * isph3a.c
+ *
+ * TI OMAP3 ISP - H3A module
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: David Cohen <dacohen@gmail.com>
+ *	     Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+
+#include "isp.h"
+#include "isph3a.h"
+#include "ispstat.h"
+
+/*
+ * h3a_aewb_update_regs - Helper function to update h3a registers.
+ */
+static void h3a_aewb_setup_regs(struct ispstat *aewb, void *priv)
+{
+	struct omap3isp_h3a_aewb_config *conf = priv;
+	u32 pcr;
+	u32 win1;
+	u32 start;
+	u32 blk;
+	u32 subwin;
+
+	if (aewb->state == ISPSTAT_DISABLED)
+		return;
+
+	isp_reg_writel(aewb->isp, aewb->active_buf->dma_addr,
+		       OMAP3_ISP_IOMEM_H3A, ISPH3A_AEWBUFST);
+
+	if (!aewb->update)
+		return;
+
+	/* Converting config metadata into reg values */
+	pcr = conf->saturation_limit << ISPH3A_PCR_AEW_AVE2LMT_SHIFT;
+	pcr |= !!conf->alaw_enable << ISPH3A_PCR_AEW_ALAW_EN_SHIFT;
+
+	win1 = ((conf->win_height >> 1) - 1) << ISPH3A_AEWWIN1_WINH_SHIFT;
+	win1 |= ((conf->win_width >> 1) - 1) << ISPH3A_AEWWIN1_WINW_SHIFT;
+	win1 |= (conf->ver_win_count - 1) << ISPH3A_AEWWIN1_WINVC_SHIFT;
+	win1 |= (conf->hor_win_count - 1) << ISPH3A_AEWWIN1_WINHC_SHIFT;
+
+	start = conf->hor_win_start << ISPH3A_AEWINSTART_WINSH_SHIFT;
+	start |= conf->ver_win_start << ISPH3A_AEWINSTART_WINSV_SHIFT;
+
+	blk = conf->blk_ver_win_start << ISPH3A_AEWINBLK_WINSV_SHIFT;
+	blk |= ((conf->blk_win_height >> 1) - 1) << ISPH3A_AEWINBLK_WINH_SHIFT;
+
+	subwin = ((conf->subsample_ver_inc >> 1) - 1) <<
+		 ISPH3A_AEWSUBWIN_AEWINCV_SHIFT;
+	subwin |= ((conf->subsample_hor_inc >> 1) - 1) <<
+		  ISPH3A_AEWSUBWIN_AEWINCH_SHIFT;
+
+	isp_reg_writel(aewb->isp, win1, OMAP3_ISP_IOMEM_H3A, ISPH3A_AEWWIN1);
+	isp_reg_writel(aewb->isp, start, OMAP3_ISP_IOMEM_H3A,
+		       ISPH3A_AEWINSTART);
+	isp_reg_writel(aewb->isp, blk, OMAP3_ISP_IOMEM_H3A, ISPH3A_AEWINBLK);
+	isp_reg_writel(aewb->isp, subwin, OMAP3_ISP_IOMEM_H3A,
+		       ISPH3A_AEWSUBWIN);
+	isp_reg_clr_set(aewb->isp, OMAP3_ISP_IOMEM_H3A, ISPH3A_PCR,
+			ISPH3A_PCR_AEW_MASK, pcr);
+
+	aewb->update = 0;
+	aewb->config_counter += aewb->inc_config;
+	aewb->inc_config = 0;
+	aewb->buf_size = conf->buf_size;
+}
+
+static void h3a_aewb_enable(struct ispstat *aewb, int enable)
+{
+	if (enable) {
+		isp_reg_set(aewb->isp, OMAP3_ISP_IOMEM_H3A, ISPH3A_PCR,
+			    ISPH3A_PCR_AEW_EN);
+		omap3isp_subclk_enable(aewb->isp, OMAP3_ISP_SUBCLK_AEWB);
+	} else {
+		isp_reg_clr(aewb->isp, OMAP3_ISP_IOMEM_H3A, ISPH3A_PCR,
+			    ISPH3A_PCR_AEW_EN);
+		omap3isp_subclk_disable(aewb->isp, OMAP3_ISP_SUBCLK_AEWB);
+	}
+}
+
+static int h3a_aewb_busy(struct ispstat *aewb)
+{
+	return isp_reg_readl(aewb->isp, OMAP3_ISP_IOMEM_H3A, ISPH3A_PCR)
+						& ISPH3A_PCR_BUSYAEAWB;
+}
+
+static u32 h3a_aewb_get_buf_size(struct omap3isp_h3a_aewb_config *conf)
+{
+	/* Number of configured windows + extra row for black data */
+	u32 win_count = (conf->ver_win_count + 1) * conf->hor_win_count;
+
+	/*
+	 * Unsaturated block counts for each 8 windows.
+	 * 1 extra for the last (win_count % 8) windows if win_count is not
+	 * divisible by 8.
+	 */
+	win_count += (win_count + 7) / 8;
+
+	return win_count * AEWB_PACKET_SIZE;
+}
+
+static int h3a_aewb_validate_params(struct ispstat *aewb, void *new_conf)
+{
+	struct omap3isp_h3a_aewb_config *user_cfg = new_conf;
+	u32 buf_size;
+
+	if (unlikely(user_cfg->saturation_limit >
+		     OMAP3ISP_AEWB_MAX_SATURATION_LIM))
+		return -EINVAL;
+
+	if (unlikely(user_cfg->win_height < OMAP3ISP_AEWB_MIN_WIN_H ||
+		     user_cfg->win_height > OMAP3ISP_AEWB_MAX_WIN_H ||
+		     user_cfg->win_height & 0x01))
+		return -EINVAL;
+
+	if (unlikely(user_cfg->win_width < OMAP3ISP_AEWB_MIN_WIN_W ||
+		     user_cfg->win_width > OMAP3ISP_AEWB_MAX_WIN_W ||
+		     user_cfg->win_width & 0x01))
+		return -EINVAL;
+
+	if (unlikely(user_cfg->ver_win_count < OMAP3ISP_AEWB_MIN_WINVC ||
+		     user_cfg->ver_win_count > OMAP3ISP_AEWB_MAX_WINVC))
+		return -EINVAL;
+
+	if (unlikely(user_cfg->hor_win_count < OMAP3ISP_AEWB_MIN_WINHC ||
+		     user_cfg->hor_win_count > OMAP3ISP_AEWB_MAX_WINHC))
+		return -EINVAL;
+
+	if (unlikely(user_cfg->ver_win_start > OMAP3ISP_AEWB_MAX_WINSTART))
+		return -EINVAL;
+
+	if (unlikely(user_cfg->hor_win_start > OMAP3ISP_AEWB_MAX_WINSTART))
+		return -EINVAL;
+
+	if (unlikely(user_cfg->blk_ver_win_start > OMAP3ISP_AEWB_MAX_WINSTART))
+		return -EINVAL;
+
+	if (unlikely(user_cfg->blk_win_height < OMAP3ISP_AEWB_MIN_WIN_H ||
+		     user_cfg->blk_win_height > OMAP3ISP_AEWB_MAX_WIN_H ||
+		     user_cfg->blk_win_height & 0x01))
+		return -EINVAL;
+
+	if (unlikely(user_cfg->subsample_ver_inc < OMAP3ISP_AEWB_MIN_SUB_INC ||
+		     user_cfg->subsample_ver_inc > OMAP3ISP_AEWB_MAX_SUB_INC ||
+		     user_cfg->subsample_ver_inc & 0x01))
+		return -EINVAL;
+
+	if (unlikely(user_cfg->subsample_hor_inc < OMAP3ISP_AEWB_MIN_SUB_INC ||
+		     user_cfg->subsample_hor_inc > OMAP3ISP_AEWB_MAX_SUB_INC ||
+		     user_cfg->subsample_hor_inc & 0x01))
+		return -EINVAL;
+
+	buf_size = h3a_aewb_get_buf_size(user_cfg);
+	if (buf_size > user_cfg->buf_size)
+		user_cfg->buf_size = buf_size;
+	else if (user_cfg->buf_size > OMAP3ISP_AEWB_MAX_BUF_SIZE)
+		user_cfg->buf_size = OMAP3ISP_AEWB_MAX_BUF_SIZE;
+
+	return 0;
+}
+
+/*
+ * h3a_aewb_set_params - Helper function to check & store user given params.
+ * @new_conf: Pointer to AE and AWB parameters struct.
+ *
+ * As most of them are busy-lock registers, need to wait until AEW_BUSY = 0 to
+ * program them during ISR.
+ */
+static void h3a_aewb_set_params(struct ispstat *aewb, void *new_conf)
+{
+	struct omap3isp_h3a_aewb_config *user_cfg = new_conf;
+	struct omap3isp_h3a_aewb_config *cur_cfg = aewb->priv;
+	int update = 0;
+
+	if (cur_cfg->saturation_limit != user_cfg->saturation_limit) {
+		cur_cfg->saturation_limit = user_cfg->saturation_limit;
+		update = 1;
+	}
+	if (cur_cfg->alaw_enable != user_cfg->alaw_enable) {
+		cur_cfg->alaw_enable = user_cfg->alaw_enable;
+		update = 1;
+	}
+	if (cur_cfg->win_height != user_cfg->win_height) {
+		cur_cfg->win_height = user_cfg->win_height;
+		update = 1;
+	}
+	if (cur_cfg->win_width != user_cfg->win_width) {
+		cur_cfg->win_width = user_cfg->win_width;
+		update = 1;
+	}
+	if (cur_cfg->ver_win_count != user_cfg->ver_win_count) {
+		cur_cfg->ver_win_count = user_cfg->ver_win_count;
+		update = 1;
+	}
+	if (cur_cfg->hor_win_count != user_cfg->hor_win_count) {
+		cur_cfg->hor_win_count = user_cfg->hor_win_count;
+		update = 1;
+	}
+	if (cur_cfg->ver_win_start != user_cfg->ver_win_start) {
+		cur_cfg->ver_win_start = user_cfg->ver_win_start;
+		update = 1;
+	}
+	if (cur_cfg->hor_win_start != user_cfg->hor_win_start) {
+		cur_cfg->hor_win_start = user_cfg->hor_win_start;
+		update = 1;
+	}
+	if (cur_cfg->blk_ver_win_start != user_cfg->blk_ver_win_start) {
+		cur_cfg->blk_ver_win_start = user_cfg->blk_ver_win_start;
+		update = 1;
+	}
+	if (cur_cfg->blk_win_height != user_cfg->blk_win_height) {
+		cur_cfg->blk_win_height = user_cfg->blk_win_height;
+		update = 1;
+	}
+	if (cur_cfg->subsample_ver_inc != user_cfg->subsample_ver_inc) {
+		cur_cfg->subsample_ver_inc = user_cfg->subsample_ver_inc;
+		update = 1;
+	}
+	if (cur_cfg->subsample_hor_inc != user_cfg->subsample_hor_inc) {
+		cur_cfg->subsample_hor_inc = user_cfg->subsample_hor_inc;
+		update = 1;
+	}
+
+	if (update || !aewb->configured) {
+		aewb->inc_config++;
+		aewb->update = 1;
+		cur_cfg->buf_size = h3a_aewb_get_buf_size(cur_cfg);
+	}
+}
+
+static long h3a_aewb_ioctl(struct v4l2_subdev *sd, unsigned int cmd, void *arg)
+{
+	struct ispstat *stat = v4l2_get_subdevdata(sd);
+
+	switch (cmd) {
+	case VIDIOC_OMAP3ISP_AEWB_CFG:
+		return omap3isp_stat_config(stat, arg);
+	case VIDIOC_OMAP3ISP_STAT_REQ:
+		return omap3isp_stat_request_statistics(stat, arg);
+	case VIDIOC_OMAP3ISP_STAT_REQ_TIME32:
+		return omap3isp_stat_request_statistics_time32(stat, arg);
+	case VIDIOC_OMAP3ISP_STAT_EN: {
+		unsigned long *en = arg;
+		return omap3isp_stat_enable(stat, !!*en);
+	}
+	}
+
+	return -ENOIOCTLCMD;
+}
+
+static const struct ispstat_ops h3a_aewb_ops = {
+	.validate_params	= h3a_aewb_validate_params,
+	.set_params		= h3a_aewb_set_params,
+	.setup_regs		= h3a_aewb_setup_regs,
+	.enable			= h3a_aewb_enable,
+	.busy			= h3a_aewb_busy,
+};
+
+static const struct v4l2_subdev_core_ops h3a_aewb_subdev_core_ops = {
+	.ioctl = h3a_aewb_ioctl,
+	.subscribe_event = omap3isp_stat_subscribe_event,
+	.unsubscribe_event = v4l2_event_subdev_unsubscribe,
+};
+
+static const struct v4l2_subdev_video_ops h3a_aewb_subdev_video_ops = {
+	.s_stream = omap3isp_stat_s_stream,
+};
+
+static const struct v4l2_subdev_ops h3a_aewb_subdev_ops = {
+	.core = &h3a_aewb_subdev_core_ops,
+	.video = &h3a_aewb_subdev_video_ops,
+};
+
+/*
+ * omap3isp_h3a_aewb_init - Module Initialisation.
+ */
+int omap3isp_h3a_aewb_init(struct isp_device *isp)
+{
+	struct ispstat *aewb = &isp->isp_aewb;
+	struct omap3isp_h3a_aewb_config *aewb_cfg;
+	struct omap3isp_h3a_aewb_config *aewb_recover_cfg = NULL;
+	int ret;
+
+	aewb_cfg = kzalloc_obj(*aewb_cfg);
+	if (!aewb_cfg)
+		return -ENOMEM;
+
+	aewb->ops = &h3a_aewb_ops;
+	aewb->priv = aewb_cfg;
+	aewb->event_type = V4L2_EVENT_OMAP3ISP_AEWB;
+	aewb->isp = isp;
+
+	/* Set recover state configuration */
+	aewb_recover_cfg = kzalloc_obj(*aewb_recover_cfg);
+	if (!aewb_recover_cfg) {
+		dev_err(aewb->isp->dev,
+			"AEWB: cannot allocate memory for recover configuration.\n");
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	aewb_recover_cfg->saturation_limit = OMAP3ISP_AEWB_MAX_SATURATION_LIM;
+	aewb_recover_cfg->win_height = OMAP3ISP_AEWB_MIN_WIN_H;
+	aewb_recover_cfg->win_width = OMAP3ISP_AEWB_MIN_WIN_W;
+	aewb_recover_cfg->ver_win_count = OMAP3ISP_AEWB_MIN_WINVC;
+	aewb_recover_cfg->hor_win_count = OMAP3ISP_AEWB_MIN_WINHC;
+	aewb_recover_cfg->blk_ver_win_start = aewb_recover_cfg->ver_win_start +
+		aewb_recover_cfg->win_height * aewb_recover_cfg->ver_win_count;
+	aewb_recover_cfg->blk_win_height = OMAP3ISP_AEWB_MIN_WIN_H;
+	aewb_recover_cfg->subsample_ver_inc = OMAP3ISP_AEWB_MIN_SUB_INC;
+	aewb_recover_cfg->subsample_hor_inc = OMAP3ISP_AEWB_MIN_SUB_INC;
+
+	if (h3a_aewb_validate_params(aewb, aewb_recover_cfg)) {
+		dev_err(aewb->isp->dev,
+			"AEWB: recover configuration is invalid.\n");
+		ret = -EINVAL;
+		goto err;
+	}
+
+	aewb_recover_cfg->buf_size = h3a_aewb_get_buf_size(aewb_recover_cfg);
+	aewb->recover_priv = aewb_recover_cfg;
+
+	ret = omap3isp_stat_init(aewb, "AEWB", &h3a_aewb_subdev_ops);
+
+err:
+	if (ret) {
+		kfree(aewb_cfg);
+		kfree(aewb_recover_cfg);
+	}
+
+	return ret;
+}
+
+/*
+ * omap3isp_h3a_aewb_cleanup - Module exit.
+ */
+void omap3isp_h3a_aewb_cleanup(struct isp_device *isp)
+{
+	omap3isp_stat_cleanup(&isp->isp_aewb);
+}

linux-7.2.3/drivers/media/platform/ti/omap3isp/isph3a_af.c

@@ -0,0 +1,405 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * isph3a_af.c
+ *
+ * TI OMAP3 ISP - H3A AF module
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: David Cohen <dacohen@gmail.com>
+ *	     Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+/* Linux specific include files */
+#include <linux/device.h>
+#include <linux/slab.h>
+
+#include "isp.h"
+#include "isph3a.h"
+#include "ispstat.h"
+
+#define IS_OUT_OF_BOUNDS(value, min, max)		\
+	((((unsigned int)value) < (min)) || (((unsigned int)value) > (max)))
+
+static void h3a_af_setup_regs(struct ispstat *af, void *priv)
+{
+	struct omap3isp_h3a_af_config *conf = priv;
+	u32 pcr;
+	u32 pax1;
+	u32 pax2;
+	u32 paxstart;
+	u32 coef;
+	u32 base_coef_set0;
+	u32 base_coef_set1;
+	int index;
+
+	if (af->state == ISPSTAT_DISABLED)
+		return;
+
+	isp_reg_writel(af->isp, af->active_buf->dma_addr, OMAP3_ISP_IOMEM_H3A,
+		       ISPH3A_AFBUFST);
+
+	if (!af->update)
+		return;
+
+	/* Configure Hardware Registers */
+	pax1 = ((conf->paxel.width >> 1) - 1) << AF_PAXW_SHIFT;
+	/* Set height in AFPAX1 */
+	pax1 |= (conf->paxel.height >> 1) - 1;
+	isp_reg_writel(af->isp, pax1, OMAP3_ISP_IOMEM_H3A, ISPH3A_AFPAX1);
+
+	/* Configure AFPAX2 Register */
+	/* Set Line Increment in AFPAX2 Register */
+	pax2 = ((conf->paxel.line_inc >> 1) - 1) << AF_LINE_INCR_SHIFT;
+	/* Set Vertical Count */
+	pax2 |= (conf->paxel.v_cnt - 1) << AF_VT_COUNT_SHIFT;
+	/* Set Horizontal Count */
+	pax2 |= (conf->paxel.h_cnt - 1);
+	isp_reg_writel(af->isp, pax2, OMAP3_ISP_IOMEM_H3A, ISPH3A_AFPAX2);
+
+	/* Configure PAXSTART Register */
+	/*Configure Horizontal Start */
+	paxstart = conf->paxel.h_start << AF_HZ_START_SHIFT;
+	/* Configure Vertical Start */
+	paxstart |= conf->paxel.v_start;
+	isp_reg_writel(af->isp, paxstart, OMAP3_ISP_IOMEM_H3A,
+		       ISPH3A_AFPAXSTART);
+
+	/*SetIIRSH Register */
+	isp_reg_writel(af->isp, conf->iir.h_start,
+		       OMAP3_ISP_IOMEM_H3A, ISPH3A_AFIIRSH);
+
+	base_coef_set0 = ISPH3A_AFCOEF010;
+	base_coef_set1 = ISPH3A_AFCOEF110;
+	for (index = 0; index <= 8; index += 2) {
+		/*Set IIR Filter0 Coefficients */
+		coef = 0;
+		coef |= conf->iir.coeff_set0[index];
+		coef |= conf->iir.coeff_set0[index + 1] <<
+			AF_COEF_SHIFT;
+		isp_reg_writel(af->isp, coef, OMAP3_ISP_IOMEM_H3A,
+			       base_coef_set0);
+		base_coef_set0 += AFCOEF_OFFSET;
+
+		/*Set IIR Filter1 Coefficients */
+		coef = 0;
+		coef |= conf->iir.coeff_set1[index];
+		coef |= conf->iir.coeff_set1[index + 1] <<
+			AF_COEF_SHIFT;
+		isp_reg_writel(af->isp, coef, OMAP3_ISP_IOMEM_H3A,
+			       base_coef_set1);
+		base_coef_set1 += AFCOEF_OFFSET;
+	}
+	/* set AFCOEF0010 Register */
+	isp_reg_writel(af->isp, conf->iir.coeff_set0[10],
+		       OMAP3_ISP_IOMEM_H3A, ISPH3A_AFCOEF0010);
+	/* set AFCOEF1010 Register */
+	isp_reg_writel(af->isp, conf->iir.coeff_set1[10],
+		       OMAP3_ISP_IOMEM_H3A, ISPH3A_AFCOEF1010);
+
+	/* PCR Register */
+	/* Set RGB Position */
+	pcr = conf->rgb_pos << AF_RGBPOS_SHIFT;
+	/* Set Accumulator Mode */
+	if (conf->fvmode == OMAP3ISP_AF_MODE_PEAK)
+		pcr |= AF_FVMODE;
+	/* Set A-law */
+	if (conf->alaw_enable)
+		pcr |= AF_ALAW_EN;
+	/* HMF Configurations */
+	if (conf->hmf.enable) {
+		/* Enable HMF */
+		pcr |= AF_MED_EN;
+		/* Set Median Threshold */
+		pcr |= conf->hmf.threshold << AF_MED_TH_SHIFT;
+	}
+	/* Set PCR Register */
+	isp_reg_clr_set(af->isp, OMAP3_ISP_IOMEM_H3A, ISPH3A_PCR,
+			AF_PCR_MASK, pcr);
+
+	af->update = 0;
+	af->config_counter += af->inc_config;
+	af->inc_config = 0;
+	af->buf_size = conf->buf_size;
+}
+
+static void h3a_af_enable(struct ispstat *af, int enable)
+{
+	if (enable) {
+		isp_reg_set(af->isp, OMAP3_ISP_IOMEM_H3A, ISPH3A_PCR,
+			    ISPH3A_PCR_AF_EN);
+		omap3isp_subclk_enable(af->isp, OMAP3_ISP_SUBCLK_AF);
+	} else {
+		isp_reg_clr(af->isp, OMAP3_ISP_IOMEM_H3A, ISPH3A_PCR,
+			    ISPH3A_PCR_AF_EN);
+		omap3isp_subclk_disable(af->isp, OMAP3_ISP_SUBCLK_AF);
+	}
+}
+
+static int h3a_af_busy(struct ispstat *af)
+{
+	return isp_reg_readl(af->isp, OMAP3_ISP_IOMEM_H3A, ISPH3A_PCR)
+						& ISPH3A_PCR_BUSYAF;
+}
+
+static u32 h3a_af_get_buf_size(struct omap3isp_h3a_af_config *conf)
+{
+	return conf->paxel.h_cnt * conf->paxel.v_cnt * OMAP3ISP_AF_PAXEL_SIZE;
+}
+
+/* Function to check paxel parameters */
+static int h3a_af_validate_params(struct ispstat *af, void *new_conf)
+{
+	struct omap3isp_h3a_af_config *user_cfg = new_conf;
+	struct omap3isp_h3a_af_paxel *paxel_cfg = &user_cfg->paxel;
+	struct omap3isp_h3a_af_iir *iir_cfg = &user_cfg->iir;
+	int index;
+	u32 buf_size;
+
+	/* Check horizontal Count */
+	if (IS_OUT_OF_BOUNDS(paxel_cfg->h_cnt,
+			     OMAP3ISP_AF_PAXEL_HORIZONTAL_COUNT_MIN,
+			     OMAP3ISP_AF_PAXEL_HORIZONTAL_COUNT_MAX))
+		return -EINVAL;
+
+	/* Check Vertical Count */
+	if (IS_OUT_OF_BOUNDS(paxel_cfg->v_cnt,
+			     OMAP3ISP_AF_PAXEL_VERTICAL_COUNT_MIN,
+			     OMAP3ISP_AF_PAXEL_VERTICAL_COUNT_MAX))
+		return -EINVAL;
+
+	if (IS_OUT_OF_BOUNDS(paxel_cfg->height, OMAP3ISP_AF_PAXEL_HEIGHT_MIN,
+			     OMAP3ISP_AF_PAXEL_HEIGHT_MAX) ||
+	    paxel_cfg->height % 2)
+		return -EINVAL;
+
+	/* Check width */
+	if (IS_OUT_OF_BOUNDS(paxel_cfg->width, OMAP3ISP_AF_PAXEL_WIDTH_MIN,
+			     OMAP3ISP_AF_PAXEL_WIDTH_MAX) ||
+	    paxel_cfg->width % 2)
+		return -EINVAL;
+
+	/* Check Line Increment */
+	if (IS_OUT_OF_BOUNDS(paxel_cfg->line_inc,
+			     OMAP3ISP_AF_PAXEL_INCREMENT_MIN,
+			     OMAP3ISP_AF_PAXEL_INCREMENT_MAX) ||
+	    paxel_cfg->line_inc % 2)
+		return -EINVAL;
+
+	/* Check Horizontal Start */
+	if ((paxel_cfg->h_start < iir_cfg->h_start) ||
+	    IS_OUT_OF_BOUNDS(paxel_cfg->h_start,
+			     OMAP3ISP_AF_PAXEL_HZSTART_MIN,
+			     OMAP3ISP_AF_PAXEL_HZSTART_MAX))
+		return -EINVAL;
+
+	/* Check IIR */
+	for (index = 0; index < OMAP3ISP_AF_NUM_COEF; index++) {
+		if ((iir_cfg->coeff_set0[index]) > OMAP3ISP_AF_COEF_MAX)
+			return -EINVAL;
+
+		if ((iir_cfg->coeff_set1[index]) > OMAP3ISP_AF_COEF_MAX)
+			return -EINVAL;
+	}
+
+	if (IS_OUT_OF_BOUNDS(iir_cfg->h_start, OMAP3ISP_AF_IIRSH_MIN,
+			     OMAP3ISP_AF_IIRSH_MAX))
+		return -EINVAL;
+
+	/* Hack: If paxel size is 12, the 10th AF window may be corrupted */
+	if ((paxel_cfg->h_cnt * paxel_cfg->v_cnt > 9) &&
+	    (paxel_cfg->width * paxel_cfg->height == 12))
+		return -EINVAL;
+
+	buf_size = h3a_af_get_buf_size(user_cfg);
+	if (buf_size > user_cfg->buf_size)
+		/* User buf_size request wasn't enough */
+		user_cfg->buf_size = buf_size;
+	else if (user_cfg->buf_size > OMAP3ISP_AF_MAX_BUF_SIZE)
+		user_cfg->buf_size = OMAP3ISP_AF_MAX_BUF_SIZE;
+
+	return 0;
+}
+
+/* Update local parameters */
+static void h3a_af_set_params(struct ispstat *af, void *new_conf)
+{
+	struct omap3isp_h3a_af_config *user_cfg = new_conf;
+	struct omap3isp_h3a_af_config *cur_cfg = af->priv;
+	int update = 0;
+	int index;
+
+	/* alaw */
+	if (cur_cfg->alaw_enable != user_cfg->alaw_enable) {
+		update = 1;
+		goto out;
+	}
+
+	/* hmf */
+	if (cur_cfg->hmf.enable != user_cfg->hmf.enable) {
+		update = 1;
+		goto out;
+	}
+	if (cur_cfg->hmf.threshold != user_cfg->hmf.threshold) {
+		update = 1;
+		goto out;
+	}
+
+	/* rgbpos */
+	if (cur_cfg->rgb_pos != user_cfg->rgb_pos) {
+		update = 1;
+		goto out;
+	}
+
+	/* iir */
+	if (cur_cfg->iir.h_start != user_cfg->iir.h_start) {
+		update = 1;
+		goto out;
+	}
+	for (index = 0; index < OMAP3ISP_AF_NUM_COEF; index++) {
+		if (cur_cfg->iir.coeff_set0[index] !=
+				user_cfg->iir.coeff_set0[index]) {
+			update = 1;
+			goto out;
+		}
+		if (cur_cfg->iir.coeff_set1[index] !=
+				user_cfg->iir.coeff_set1[index]) {
+			update = 1;
+			goto out;
+		}
+	}
+
+	/* paxel */
+	if ((cur_cfg->paxel.width != user_cfg->paxel.width) ||
+	    (cur_cfg->paxel.height != user_cfg->paxel.height) ||
+	    (cur_cfg->paxel.h_start != user_cfg->paxel.h_start) ||
+	    (cur_cfg->paxel.v_start != user_cfg->paxel.v_start) ||
+	    (cur_cfg->paxel.h_cnt != user_cfg->paxel.h_cnt) ||
+	    (cur_cfg->paxel.v_cnt != user_cfg->paxel.v_cnt) ||
+	    (cur_cfg->paxel.line_inc != user_cfg->paxel.line_inc)) {
+		update = 1;
+		goto out;
+	}
+
+	/* af_mode */
+	if (cur_cfg->fvmode != user_cfg->fvmode)
+		update = 1;
+
+out:
+	if (update || !af->configured) {
+		memcpy(cur_cfg, user_cfg, sizeof(*cur_cfg));
+		af->inc_config++;
+		af->update = 1;
+		/*
+		 * User might be asked for a bigger buffer than necessary for
+		 * this configuration. In order to return the right amount of
+		 * data during buffer request, let's calculate the size here
+		 * instead of stick with user_cfg->buf_size.
+		 */
+		cur_cfg->buf_size = h3a_af_get_buf_size(cur_cfg);
+	}
+}
+
+static long h3a_af_ioctl(struct v4l2_subdev *sd, unsigned int cmd, void *arg)
+{
+	struct ispstat *stat = v4l2_get_subdevdata(sd);
+
+	switch (cmd) {
+	case VIDIOC_OMAP3ISP_AF_CFG:
+		return omap3isp_stat_config(stat, arg);
+	case VIDIOC_OMAP3ISP_STAT_REQ:
+		return omap3isp_stat_request_statistics(stat, arg);
+	case VIDIOC_OMAP3ISP_STAT_REQ_TIME32:
+		return omap3isp_stat_request_statistics_time32(stat, arg);
+	case VIDIOC_OMAP3ISP_STAT_EN: {
+		int *en = arg;
+		return omap3isp_stat_enable(stat, !!*en);
+	}
+	}
+
+	return -ENOIOCTLCMD;
+
+}
+
+static const struct ispstat_ops h3a_af_ops = {
+	.validate_params	= h3a_af_validate_params,
+	.set_params		= h3a_af_set_params,
+	.setup_regs		= h3a_af_setup_regs,
+	.enable			= h3a_af_enable,
+	.busy			= h3a_af_busy,
+};
+
+static const struct v4l2_subdev_core_ops h3a_af_subdev_core_ops = {
+	.ioctl = h3a_af_ioctl,
+	.subscribe_event = omap3isp_stat_subscribe_event,
+	.unsubscribe_event = v4l2_event_subdev_unsubscribe,
+};
+
+static const struct v4l2_subdev_video_ops h3a_af_subdev_video_ops = {
+	.s_stream = omap3isp_stat_s_stream,
+};
+
+static const struct v4l2_subdev_ops h3a_af_subdev_ops = {
+	.core = &h3a_af_subdev_core_ops,
+	.video = &h3a_af_subdev_video_ops,
+};
+
+/* Function to register the AF character device driver. */
+int omap3isp_h3a_af_init(struct isp_device *isp)
+{
+	struct ispstat *af = &isp->isp_af;
+	struct omap3isp_h3a_af_config *af_cfg;
+	struct omap3isp_h3a_af_config *af_recover_cfg = NULL;
+	int ret;
+
+	af_cfg = kzalloc_obj(*af_cfg);
+	if (af_cfg == NULL)
+		return -ENOMEM;
+
+	af->ops = &h3a_af_ops;
+	af->priv = af_cfg;
+	af->event_type = V4L2_EVENT_OMAP3ISP_AF;
+	af->isp = isp;
+
+	/* Set recover state configuration */
+	af_recover_cfg = kzalloc_obj(*af_recover_cfg);
+	if (!af_recover_cfg) {
+		dev_err(af->isp->dev,
+			"AF: cannot allocate memory for recover configuration.\n");
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	af_recover_cfg->paxel.h_start = OMAP3ISP_AF_PAXEL_HZSTART_MIN;
+	af_recover_cfg->paxel.width = OMAP3ISP_AF_PAXEL_WIDTH_MIN;
+	af_recover_cfg->paxel.height = OMAP3ISP_AF_PAXEL_HEIGHT_MIN;
+	af_recover_cfg->paxel.h_cnt = OMAP3ISP_AF_PAXEL_HORIZONTAL_COUNT_MIN;
+	af_recover_cfg->paxel.v_cnt = OMAP3ISP_AF_PAXEL_VERTICAL_COUNT_MIN;
+	af_recover_cfg->paxel.line_inc = OMAP3ISP_AF_PAXEL_INCREMENT_MIN;
+	if (h3a_af_validate_params(af, af_recover_cfg)) {
+		dev_err(af->isp->dev,
+			"AF: recover configuration is invalid.\n");
+		ret = -EINVAL;
+		goto err;
+	}
+
+	af_recover_cfg->buf_size = h3a_af_get_buf_size(af_recover_cfg);
+	af->recover_priv = af_recover_cfg;
+
+	ret = omap3isp_stat_init(af, "AF", &h3a_af_subdev_ops);
+
+err:
+	if (ret) {
+		kfree(af_cfg);
+		kfree(af_recover_cfg);
+	}
+
+	return ret;
+}
+
+void omap3isp_h3a_af_cleanup(struct isp_device *isp)
+{
+	omap3isp_stat_cleanup(&isp->isp_af);
+}

linux-7.2.3/drivers/media/platform/ti/omap3isp/isphist.c

@@ -0,0 +1,540 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * isphist.c
+ *
+ * TI OMAP3 ISP - Histogram module
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: David Cohen <dacohen@gmail.com>
+ *	     Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dmaengine.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+
+#include "isp.h"
+#include "ispreg.h"
+#include "isphist.h"
+
+#define HIST_CONFIG_DMA	1
+
+/*
+ * hist_reset_mem - clear Histogram memory before start stats engine.
+ */
+static void hist_reset_mem(struct ispstat *hist)
+{
+	struct isp_device *isp = hist->isp;
+	struct omap3isp_hist_config *conf = hist->priv;
+	unsigned int i;
+
+	isp_reg_writel(isp, 0, OMAP3_ISP_IOMEM_HIST, ISPHIST_ADDR);
+
+	/*
+	 * By setting it, the histogram internal buffer is being cleared at the
+	 * same time it's being read. This bit must be cleared afterwards.
+	 */
+	isp_reg_set(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT, ISPHIST_CNT_CLEAR);
+
+	/*
+	 * We'll clear 4 words at each iteration for optimization. It avoids
+	 * 3/4 of the jumps. We also know HIST_MEM_SIZE is divisible by 4.
+	 */
+	for (i = OMAP3ISP_HIST_MEM_SIZE / 4; i > 0; i--) {
+		isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA);
+		isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA);
+		isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA);
+		isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA);
+	}
+	isp_reg_clr(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT, ISPHIST_CNT_CLEAR);
+
+	hist->wait_acc_frames = conf->num_acc_frames;
+}
+
+/*
+ * hist_setup_regs - Helper function to update Histogram registers.
+ */
+static void hist_setup_regs(struct ispstat *hist, void *priv)
+{
+	struct isp_device *isp = hist->isp;
+	struct omap3isp_hist_config *conf = priv;
+	int c;
+	u32 cnt;
+	u32 wb_gain;
+	u32 reg_hor[OMAP3ISP_HIST_MAX_REGIONS];
+	u32 reg_ver[OMAP3ISP_HIST_MAX_REGIONS];
+
+	if (!hist->update || hist->state == ISPSTAT_DISABLED ||
+	    hist->state == ISPSTAT_DISABLING)
+		return;
+
+	cnt = conf->cfa << ISPHIST_CNT_CFA_SHIFT;
+
+	wb_gain = conf->wg[0] << ISPHIST_WB_GAIN_WG00_SHIFT;
+	wb_gain |= conf->wg[1] << ISPHIST_WB_GAIN_WG01_SHIFT;
+	wb_gain |= conf->wg[2] << ISPHIST_WB_GAIN_WG02_SHIFT;
+	if (conf->cfa == OMAP3ISP_HIST_CFA_BAYER)
+		wb_gain |= conf->wg[3] << ISPHIST_WB_GAIN_WG03_SHIFT;
+
+	/* Regions size and position */
+	for (c = 0; c < OMAP3ISP_HIST_MAX_REGIONS; c++) {
+		if (c < conf->num_regions) {
+			reg_hor[c] = (conf->region[c].h_start <<
+				     ISPHIST_REG_START_SHIFT)
+				   | (conf->region[c].h_end <<
+				     ISPHIST_REG_END_SHIFT);
+			reg_ver[c] = (conf->region[c].v_start <<
+				     ISPHIST_REG_START_SHIFT)
+				   | (conf->region[c].v_end <<
+				     ISPHIST_REG_END_SHIFT);
+		} else {
+			reg_hor[c] = 0;
+			reg_ver[c] = 0;
+		}
+	}
+
+	cnt |= conf->hist_bins << ISPHIST_CNT_BINS_SHIFT;
+	switch (conf->hist_bins) {
+	case OMAP3ISP_HIST_BINS_256:
+		cnt |= (ISPHIST_IN_BIT_WIDTH_CCDC - 8) <<
+			ISPHIST_CNT_SHIFT_SHIFT;
+		break;
+	case OMAP3ISP_HIST_BINS_128:
+		cnt |= (ISPHIST_IN_BIT_WIDTH_CCDC - 7) <<
+			ISPHIST_CNT_SHIFT_SHIFT;
+		break;
+	case OMAP3ISP_HIST_BINS_64:
+		cnt |= (ISPHIST_IN_BIT_WIDTH_CCDC - 6) <<
+			ISPHIST_CNT_SHIFT_SHIFT;
+		break;
+	default: /* OMAP3ISP_HIST_BINS_32 */
+		cnt |= (ISPHIST_IN_BIT_WIDTH_CCDC - 5) <<
+			ISPHIST_CNT_SHIFT_SHIFT;
+		break;
+	}
+
+	hist_reset_mem(hist);
+
+	isp_reg_writel(isp, cnt, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT);
+	isp_reg_writel(isp, wb_gain,  OMAP3_ISP_IOMEM_HIST, ISPHIST_WB_GAIN);
+	isp_reg_writel(isp, reg_hor[0], OMAP3_ISP_IOMEM_HIST, ISPHIST_R0_HORZ);
+	isp_reg_writel(isp, reg_ver[0], OMAP3_ISP_IOMEM_HIST, ISPHIST_R0_VERT);
+	isp_reg_writel(isp, reg_hor[1], OMAP3_ISP_IOMEM_HIST, ISPHIST_R1_HORZ);
+	isp_reg_writel(isp, reg_ver[1], OMAP3_ISP_IOMEM_HIST, ISPHIST_R1_VERT);
+	isp_reg_writel(isp, reg_hor[2], OMAP3_ISP_IOMEM_HIST, ISPHIST_R2_HORZ);
+	isp_reg_writel(isp, reg_ver[2], OMAP3_ISP_IOMEM_HIST, ISPHIST_R2_VERT);
+	isp_reg_writel(isp, reg_hor[3], OMAP3_ISP_IOMEM_HIST, ISPHIST_R3_HORZ);
+	isp_reg_writel(isp, reg_ver[3], OMAP3_ISP_IOMEM_HIST, ISPHIST_R3_VERT);
+
+	hist->update = 0;
+	hist->config_counter += hist->inc_config;
+	hist->inc_config = 0;
+	hist->buf_size = conf->buf_size;
+}
+
+static void hist_enable(struct ispstat *hist, int enable)
+{
+	if (enable) {
+		isp_reg_set(hist->isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_PCR,
+			    ISPHIST_PCR_ENABLE);
+		omap3isp_subclk_enable(hist->isp, OMAP3_ISP_SUBCLK_HIST);
+	} else {
+		isp_reg_clr(hist->isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_PCR,
+			    ISPHIST_PCR_ENABLE);
+		omap3isp_subclk_disable(hist->isp, OMAP3_ISP_SUBCLK_HIST);
+	}
+}
+
+static int hist_busy(struct ispstat *hist)
+{
+	return isp_reg_readl(hist->isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_PCR)
+						& ISPHIST_PCR_BUSY;
+}
+
+static void hist_dma_cb(void *data)
+{
+	struct ispstat *hist = data;
+
+	/* FIXME: The DMA engine API can't report transfer errors :-/ */
+
+	isp_reg_clr(hist->isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT,
+		    ISPHIST_CNT_CLEAR);
+
+	omap3isp_stat_dma_isr(hist);
+	if (hist->state != ISPSTAT_DISABLED)
+		omap3isp_hist_dma_done(hist->isp);
+}
+
+static int hist_buf_dma(struct ispstat *hist)
+{
+	dma_addr_t dma_addr = hist->active_buf->dma_addr;
+	struct dma_async_tx_descriptor *tx;
+	struct dma_slave_config cfg;
+	dma_cookie_t cookie;
+	int ret;
+
+	if (unlikely(!dma_addr)) {
+		dev_dbg(hist->isp->dev, "hist: invalid DMA buffer address\n");
+		goto error;
+	}
+
+	isp_reg_writel(hist->isp, 0, OMAP3_ISP_IOMEM_HIST, ISPHIST_ADDR);
+	isp_reg_set(hist->isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT,
+		    ISPHIST_CNT_CLEAR);
+	omap3isp_flush(hist->isp);
+
+	memset(&cfg, 0, sizeof(cfg));
+	cfg.src_addr = hist->isp->mmio_hist_base_phys + ISPHIST_DATA;
+	cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+	cfg.src_maxburst = hist->buf_size / 4;
+
+	ret = dmaengine_slave_config(hist->dma_ch, &cfg);
+	if (ret < 0) {
+		dev_dbg(hist->isp->dev,
+			"hist: DMA slave configuration failed\n");
+		goto error;
+	}
+
+	tx = dmaengine_prep_slave_single(hist->dma_ch, dma_addr,
+					 hist->buf_size, DMA_DEV_TO_MEM,
+					 DMA_CTRL_ACK);
+	if (tx == NULL) {
+		dev_dbg(hist->isp->dev,
+			"hist: DMA slave preparation failed\n");
+		goto error;
+	}
+
+	tx->callback = hist_dma_cb;
+	tx->callback_param = hist;
+	cookie = tx->tx_submit(tx);
+	if (dma_submit_error(cookie)) {
+		dev_dbg(hist->isp->dev, "hist: DMA submission failed\n");
+		goto error;
+	}
+
+	dma_async_issue_pending(hist->dma_ch);
+
+	return STAT_BUF_WAITING_DMA;
+
+error:
+	hist_reset_mem(hist);
+	return STAT_NO_BUF;
+}
+
+static int hist_buf_pio(struct ispstat *hist)
+{
+	struct isp_device *isp = hist->isp;
+	u32 *buf = hist->active_buf->virt_addr;
+	unsigned int i;
+
+	if (!buf) {
+		dev_dbg(isp->dev, "hist: invalid PIO buffer address\n");
+		hist_reset_mem(hist);
+		return STAT_NO_BUF;
+	}
+
+	isp_reg_writel(isp, 0, OMAP3_ISP_IOMEM_HIST, ISPHIST_ADDR);
+
+	/*
+	 * By setting it, the histogram internal buffer is being cleared at the
+	 * same time it's being read. This bit must be cleared just after all
+	 * data is acquired.
+	 */
+	isp_reg_set(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT, ISPHIST_CNT_CLEAR);
+
+	/*
+	 * We'll read 4 times a 4-bytes-word at each iteration for
+	 * optimization. It avoids 3/4 of the jumps. We also know buf_size is
+	 * divisible by 16.
+	 */
+	for (i = hist->buf_size / 16; i > 0; i--) {
+		*buf++ = isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA);
+		*buf++ = isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA);
+		*buf++ = isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA);
+		*buf++ = isp_reg_readl(isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_DATA);
+	}
+	isp_reg_clr(hist->isp, OMAP3_ISP_IOMEM_HIST, ISPHIST_CNT,
+		    ISPHIST_CNT_CLEAR);
+
+	return STAT_BUF_DONE;
+}
+
+/*
+ * hist_buf_process - Callback from ISP driver for HIST interrupt.
+ */
+static int hist_buf_process(struct ispstat *hist)
+{
+	struct omap3isp_hist_config *user_cfg = hist->priv;
+	int ret;
+
+	if (atomic_read(&hist->buf_err) || hist->state != ISPSTAT_ENABLED) {
+		hist_reset_mem(hist);
+		return STAT_NO_BUF;
+	}
+
+	if (--(hist->wait_acc_frames))
+		return STAT_NO_BUF;
+
+	if (hist->dma_ch)
+		ret = hist_buf_dma(hist);
+	else
+		ret = hist_buf_pio(hist);
+
+	hist->wait_acc_frames = user_cfg->num_acc_frames;
+
+	return ret;
+}
+
+static u32 hist_get_buf_size(struct omap3isp_hist_config *conf)
+{
+	return OMAP3ISP_HIST_MEM_SIZE_BINS(conf->hist_bins) * conf->num_regions;
+}
+
+/*
+ * hist_validate_params - Helper function to check user given params.
+ * @new_conf: Pointer to user configuration structure.
+ *
+ * Returns 0 on success configuration.
+ */
+static int hist_validate_params(struct ispstat *hist, void *new_conf)
+{
+	struct omap3isp_hist_config *user_cfg = new_conf;
+	int c;
+	u32 buf_size;
+
+	if (user_cfg->cfa > OMAP3ISP_HIST_CFA_FOVEONX3)
+		return -EINVAL;
+
+	/* Regions size and position */
+
+	if ((user_cfg->num_regions < OMAP3ISP_HIST_MIN_REGIONS) ||
+	    (user_cfg->num_regions > OMAP3ISP_HIST_MAX_REGIONS))
+		return -EINVAL;
+
+	/* Regions */
+	for (c = 0; c < user_cfg->num_regions; c++) {
+		if (user_cfg->region[c].h_start & ~ISPHIST_REG_START_END_MASK)
+			return -EINVAL;
+		if (user_cfg->region[c].h_end & ~ISPHIST_REG_START_END_MASK)
+			return -EINVAL;
+		if (user_cfg->region[c].v_start & ~ISPHIST_REG_START_END_MASK)
+			return -EINVAL;
+		if (user_cfg->region[c].v_end & ~ISPHIST_REG_START_END_MASK)
+			return -EINVAL;
+		if (user_cfg->region[c].h_start > user_cfg->region[c].h_end)
+			return -EINVAL;
+		if (user_cfg->region[c].v_start > user_cfg->region[c].v_end)
+			return -EINVAL;
+	}
+
+	switch (user_cfg->num_regions) {
+	case 1:
+		if (user_cfg->hist_bins > OMAP3ISP_HIST_BINS_256)
+			return -EINVAL;
+		break;
+	case 2:
+		if (user_cfg->hist_bins > OMAP3ISP_HIST_BINS_128)
+			return -EINVAL;
+		break;
+	default: /* 3 or 4 */
+		if (user_cfg->hist_bins > OMAP3ISP_HIST_BINS_64)
+			return -EINVAL;
+		break;
+	}
+
+	buf_size = hist_get_buf_size(user_cfg);
+	if (buf_size > user_cfg->buf_size)
+		/* User's buf_size request wasn't enough */
+		user_cfg->buf_size = buf_size;
+	else if (user_cfg->buf_size > OMAP3ISP_HIST_MAX_BUF_SIZE)
+		user_cfg->buf_size = OMAP3ISP_HIST_MAX_BUF_SIZE;
+
+	return 0;
+}
+
+static int hist_comp_params(struct ispstat *hist,
+			    struct omap3isp_hist_config *user_cfg)
+{
+	struct omap3isp_hist_config *cur_cfg = hist->priv;
+	int c;
+
+	if (cur_cfg->cfa != user_cfg->cfa)
+		return 1;
+
+	if (cur_cfg->num_acc_frames != user_cfg->num_acc_frames)
+		return 1;
+
+	if (cur_cfg->hist_bins != user_cfg->hist_bins)
+		return 1;
+
+	for (c = 0; c < OMAP3ISP_HIST_MAX_WG; c++) {
+		if (c == 3 && user_cfg->cfa == OMAP3ISP_HIST_CFA_FOVEONX3)
+			break;
+		else if (cur_cfg->wg[c] != user_cfg->wg[c])
+			return 1;
+	}
+
+	if (cur_cfg->num_regions != user_cfg->num_regions)
+		return 1;
+
+	/* Regions */
+	for (c = 0; c < user_cfg->num_regions; c++) {
+		if (cur_cfg->region[c].h_start != user_cfg->region[c].h_start)
+			return 1;
+		if (cur_cfg->region[c].h_end != user_cfg->region[c].h_end)
+			return 1;
+		if (cur_cfg->region[c].v_start != user_cfg->region[c].v_start)
+			return 1;
+		if (cur_cfg->region[c].v_end != user_cfg->region[c].v_end)
+			return 1;
+	}
+
+	return 0;
+}
+
+/*
+ * hist_update_params - Helper function to check and store user given params.
+ * @new_conf: Pointer to user configuration structure.
+ */
+static void hist_set_params(struct ispstat *hist, void *new_conf)
+{
+	struct omap3isp_hist_config *user_cfg = new_conf;
+	struct omap3isp_hist_config *cur_cfg = hist->priv;
+
+	if (!hist->configured || hist_comp_params(hist, user_cfg)) {
+		memcpy(cur_cfg, user_cfg, sizeof(*user_cfg));
+		if (user_cfg->num_acc_frames == 0)
+			user_cfg->num_acc_frames = 1;
+		hist->inc_config++;
+		hist->update = 1;
+		/*
+		 * User might be asked for a bigger buffer than necessary for
+		 * this configuration. In order to return the right amount of
+		 * data during buffer request, let's calculate the size here
+		 * instead of stick with user_cfg->buf_size.
+		 */
+		cur_cfg->buf_size = hist_get_buf_size(cur_cfg);
+
+	}
+}
+
+static long hist_ioctl(struct v4l2_subdev *sd, unsigned int cmd, void *arg)
+{
+	struct ispstat *stat = v4l2_get_subdevdata(sd);
+
+	switch (cmd) {
+	case VIDIOC_OMAP3ISP_HIST_CFG:
+		return omap3isp_stat_config(stat, arg);
+	case VIDIOC_OMAP3ISP_STAT_REQ:
+		return omap3isp_stat_request_statistics(stat, arg);
+	case VIDIOC_OMAP3ISP_STAT_REQ_TIME32:
+		return omap3isp_stat_request_statistics_time32(stat, arg);
+	case VIDIOC_OMAP3ISP_STAT_EN: {
+		int *en = arg;
+		return omap3isp_stat_enable(stat, !!*en);
+	}
+	}
+
+	return -ENOIOCTLCMD;
+
+}
+
+static const struct ispstat_ops hist_ops = {
+	.validate_params	= hist_validate_params,
+	.set_params		= hist_set_params,
+	.setup_regs		= hist_setup_regs,
+	.enable			= hist_enable,
+	.busy			= hist_busy,
+	.buf_process		= hist_buf_process,
+};
+
+static const struct v4l2_subdev_core_ops hist_subdev_core_ops = {
+	.ioctl = hist_ioctl,
+	.subscribe_event = omap3isp_stat_subscribe_event,
+	.unsubscribe_event = v4l2_event_subdev_unsubscribe,
+};
+
+static const struct v4l2_subdev_video_ops hist_subdev_video_ops = {
+	.s_stream = omap3isp_stat_s_stream,
+};
+
+static const struct v4l2_subdev_ops hist_subdev_ops = {
+	.core = &hist_subdev_core_ops,
+	.video = &hist_subdev_video_ops,
+};
+
+/*
+ * omap3isp_hist_init - Module Initialization.
+ */
+int omap3isp_hist_init(struct isp_device *isp)
+{
+	struct ispstat *hist = &isp->isp_hist;
+	struct omap3isp_hist_config *hist_cfg;
+	int ret;
+
+	hist_cfg = kzalloc_obj(*hist_cfg);
+	if (hist_cfg == NULL)
+		return -ENOMEM;
+
+	hist->isp = isp;
+
+	if (HIST_CONFIG_DMA) {
+		dma_cap_mask_t mask;
+
+		/*
+		 * We need slave capable channel without DMA request line for
+		 * reading out the data.
+		 * For this we can use dma_request_chan_by_mask() as we are
+		 * happy with any channel as long as it is capable of slave
+		 * configuration.
+		 */
+		dma_cap_zero(mask);
+		dma_cap_set(DMA_SLAVE, mask);
+		hist->dma_ch = dma_request_chan_by_mask(&mask);
+		if (IS_ERR(hist->dma_ch)) {
+			ret = PTR_ERR(hist->dma_ch);
+			if (ret == -EPROBE_DEFER)
+				goto err;
+
+			hist->dma_ch = NULL;
+			dev_warn(isp->dev,
+				 "hist: DMA channel request failed, using PIO\n");
+		} else {
+			dev_dbg(isp->dev, "hist: using DMA channel %s\n",
+				dma_chan_name(hist->dma_ch));
+		}
+	}
+
+	hist->ops = &hist_ops;
+	hist->priv = hist_cfg;
+	hist->event_type = V4L2_EVENT_OMAP3ISP_HIST;
+
+	ret = omap3isp_stat_init(hist, "histogram", &hist_subdev_ops);
+
+err:
+	if (ret) {
+		if (!IS_ERR_OR_NULL(hist->dma_ch))
+			dma_release_channel(hist->dma_ch);
+		kfree(hist_cfg);
+	}
+
+	return ret;
+}
+
+/*
+ * omap3isp_hist_cleanup - Module cleanup.
+ */
+void omap3isp_hist_cleanup(struct isp_device *isp)
+{
+	struct ispstat *hist = &isp->isp_hist;
+
+	if (hist->dma_ch)
+		dma_release_channel(hist->dma_ch);
+
+	omap3isp_stat_cleanup(hist);
+}

linux-7.2.3/drivers/media/platform/ti/omap3isp/isphist.h

@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * isphist.h
+ *
+ * TI OMAP3 ISP - Histogram module
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: David Cohen <dacohen@gmail.com>
+ *	     Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#ifndef OMAP3_ISP_HIST_H
+#define OMAP3_ISP_HIST_H
+
+#include <linux/omap3isp.h>
+
+#define ISPHIST_IN_BIT_WIDTH_CCDC	10
+
+struct isp_device;
+
+int omap3isp_hist_init(struct isp_device *isp);
+void omap3isp_hist_cleanup(struct isp_device *isp);
+
+#endif /* OMAP3_ISP_HIST */

linux-7.2.3/drivers/media/platform/ti/omap3isp/isppreview.h

@@ -0,0 +1,161 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * isppreview.h
+ *
+ * TI OMAP3 ISP - Preview module
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#ifndef OMAP3_ISP_PREVIEW_H
+#define OMAP3_ISP_PREVIEW_H
+
+#include <linux/omap3isp.h>
+#include <linux/types.h>
+#include <media/v4l2-ctrls.h>
+
+#include "ispvideo.h"
+
+#define ISPPRV_BRIGHT_STEP		0x1
+#define ISPPRV_BRIGHT_DEF		0x0
+#define ISPPRV_BRIGHT_LOW		0x0
+#define ISPPRV_BRIGHT_HIGH		0xFF
+#define ISPPRV_BRIGHT_UNITS		0x1
+
+#define ISPPRV_CONTRAST_STEP		0x1
+#define ISPPRV_CONTRAST_DEF		0x10
+#define ISPPRV_CONTRAST_LOW		0x0
+#define ISPPRV_CONTRAST_HIGH		0xFF
+#define ISPPRV_CONTRAST_UNITS		0x1
+
+/* Additional features not listed in linux/omap3isp.h */
+#define OMAP3ISP_PREV_CONTRAST		(1 << 17)
+#define OMAP3ISP_PREV_BRIGHTNESS	(1 << 18)
+#define OMAP3ISP_PREV_FEATURES_END	(1 << 19)
+
+enum preview_input_entity {
+	PREVIEW_INPUT_NONE,
+	PREVIEW_INPUT_CCDC,
+	PREVIEW_INPUT_MEMORY,
+};
+
+#define PREVIEW_OUTPUT_RESIZER		(1 << 1)
+#define PREVIEW_OUTPUT_MEMORY		(1 << 2)
+
+/* Configure byte layout of YUV image */
+enum preview_ycpos_mode {
+	YCPOS_YCrYCb = 0,
+	YCPOS_YCbYCr = 1,
+	YCPOS_CbYCrY = 2,
+	YCPOS_CrYCbY = 3
+};
+
+/*
+ * struct prev_params - Structure for all configuration
+ * @busy: Bitmask of busy parameters (being updated or used)
+ * @update: Bitmask of the parameters to be updated
+ * @features: Set of features enabled.
+ * @cfa: CFA coefficients.
+ * @csup: Chroma suppression coefficients.
+ * @luma: Luma enhancement coefficients.
+ * @nf: Noise filter coefficients.
+ * @dcor: Noise filter coefficients.
+ * @gamma: Gamma coefficients.
+ * @wbal: White Balance parameters.
+ * @blkadj: Black adjustment parameters.
+ * @rgb2rgb: RGB blending parameters.
+ * @csc: Color space conversion (RGB to YCbCr) parameters.
+ * @hmed: Horizontal median filter.
+ * @yclimit: YC limits parameters.
+ * @contrast: Contrast.
+ * @brightness: Brightness.
+ */
+struct prev_params {
+	u32 busy;
+	u32 update;
+	u32 features;
+	struct omap3isp_prev_cfa cfa;
+	struct omap3isp_prev_csup csup;
+	struct omap3isp_prev_luma luma;
+	struct omap3isp_prev_nf nf;
+	struct omap3isp_prev_dcor dcor;
+	struct omap3isp_prev_gtables gamma;
+	struct omap3isp_prev_wbal wbal;
+	struct omap3isp_prev_blkadj blkadj;
+	struct omap3isp_prev_rgbtorgb rgb2rgb;
+	struct omap3isp_prev_csc csc;
+	struct omap3isp_prev_hmed hmed;
+	struct omap3isp_prev_yclimit yclimit;
+	u8 contrast;
+	u8 brightness;
+};
+
+/* Sink and source previewer pads */
+#define PREV_PAD_SINK			0
+#define PREV_PAD_SOURCE			1
+#define PREV_PADS_NUM			2
+
+/*
+ * struct isp_prev_device - Structure for storing ISP Preview module information
+ * @subdev: V4L2 subdevice
+ * @pads: Media entity pads
+ * @formats: Active formats at the subdev pad
+ * @crop: Active crop rectangle
+ * @input: Module currently connected to the input pad
+ * @output: Bitmask of the active output
+ * @video_in: Input video entity
+ * @video_out: Output video entity
+ * @params.params : Active and shadow parameters sets
+ * @params.active: Bitmask of parameters active in set 0
+ * @params.lock: Parameters lock, protects params.active and params.shadow
+ * @underrun: Whether the preview entity has queued buffers on the output
+ * @state: Current preview pipeline state
+ *
+ * This structure is used to store the OMAP ISP Preview module Information.
+ */
+struct isp_prev_device {
+	struct v4l2_subdev subdev;
+	struct media_pad pads[PREV_PADS_NUM];
+	struct v4l2_mbus_framefmt formats[PREV_PADS_NUM];
+	struct v4l2_rect crop;
+
+	struct v4l2_ctrl_handler ctrls;
+
+	enum preview_input_entity input;
+	unsigned int output;
+	struct isp_video video_in;
+	struct isp_video video_out;
+
+	struct {
+		unsigned int cfa_order;
+		struct prev_params params[2];
+		u32 active;
+		spinlock_t lock;
+	} params;
+
+	enum isp_pipeline_stream_state state;
+	wait_queue_head_t wait;
+	atomic_t stopping;
+};
+
+struct isp_device;
+
+int omap3isp_preview_init(struct isp_device *isp);
+void omap3isp_preview_cleanup(struct isp_device *isp);
+
+int omap3isp_preview_register_entities(struct isp_prev_device *prv,
+				       struct v4l2_device *vdev);
+void omap3isp_preview_unregister_entities(struct isp_prev_device *prv);
+
+void omap3isp_preview_isr_frame_sync(struct isp_prev_device *prev);
+void omap3isp_preview_isr(struct isp_prev_device *prev);
+
+int omap3isp_preview_busy(struct isp_prev_device *isp_prev);
+
+void omap3isp_preview_restore_context(struct isp_device *isp);
+
+#endif	/* OMAP3_ISP_PREVIEW_H */

linux-7.2.3/drivers/media/platform/ti/omap3isp/ispresizer.h

@@ -0,0 +1,136 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * ispresizer.h
+ *
+ * TI OMAP3 ISP - Resizer module
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#ifndef OMAP3_ISP_RESIZER_H
+#define OMAP3_ISP_RESIZER_H
+
+#include <linux/spinlock.h>
+#include <linux/types.h>
+
+/*
+ * Constants for filter coefficients count
+ */
+#define COEFF_CNT		32
+
+/*
+ * struct isprsz_coef - Structure for resizer filter coefficients.
+ * @h_filter_coef_4tap: Horizontal filter coefficients for 8-phase/4-tap
+ *			mode (.5x-4x)
+ * @v_filter_coef_4tap: Vertical filter coefficients for 8-phase/4-tap
+ *			mode (.5x-4x)
+ * @h_filter_coef_7tap: Horizontal filter coefficients for 4-phase/7-tap
+ *			mode (.25x-.5x)
+ * @v_filter_coef_7tap: Vertical filter coefficients for 4-phase/7-tap
+ *			mode (.25x-.5x)
+ */
+struct isprsz_coef {
+	u16 h_filter_coef_4tap[32];
+	u16 v_filter_coef_4tap[32];
+	/* Every 8th value is a dummy value in the following arrays: */
+	u16 h_filter_coef_7tap[32];
+	u16 v_filter_coef_7tap[32];
+};
+
+/* Chrominance horizontal algorithm */
+enum resizer_chroma_algo {
+	RSZ_THE_SAME = 0,	/* Chrominance the same as Luminance */
+	RSZ_BILINEAR = 1,	/* Chrominance uses bilinear interpolation */
+};
+
+/* Resizer input type select */
+enum resizer_colors_type {
+	RSZ_YUV422 = 0,		/* YUV422 color is interleaved */
+	RSZ_COLOR8 = 1,		/* Color separate data on 8 bits */
+};
+
+/*
+ * Structure for horizontal and vertical resizing value
+ */
+struct resizer_ratio {
+	u32 horz;
+	u32 vert;
+};
+
+/*
+ * Structure for luminance enhancer parameters.
+ */
+struct resizer_luma_yenh {
+	u8 algo;		/* algorithm select. */
+	u8 gain;		/* maximum gain. */
+	u8 slope;		/* slope. */
+	u8 core;		/* core offset. */
+};
+
+enum resizer_input_entity {
+	RESIZER_INPUT_NONE,
+	RESIZER_INPUT_VP,	/* input video port - prev or ccdc */
+	RESIZER_INPUT_MEMORY,
+};
+
+/* Sink and source resizer pads */
+#define RESZ_PAD_SINK			0
+#define RESZ_PAD_SOURCE			1
+#define RESZ_PADS_NUM			2
+
+/*
+ * struct isp_res_device - OMAP3 ISP resizer module
+ * @lock: Protects formats and crop rectangles between set_selection and IRQ
+ * @crop.request: Crop rectangle requested by the user
+ * @crop.active: Active crop rectangle (based on hardware requirements)
+ */
+struct isp_res_device {
+	struct v4l2_subdev subdev;
+	struct media_pad pads[RESZ_PADS_NUM];
+	struct v4l2_mbus_framefmt formats[RESZ_PADS_NUM];
+
+	enum resizer_input_entity input;
+	struct isp_video video_in;
+	struct isp_video video_out;
+
+	u32 addr_base;   /* stored source buffer address in memory mode */
+	u32 crop_offset; /* additional offset for crop in memory mode */
+	struct resizer_ratio ratio;
+	int pm_state;
+	unsigned int applycrop:1;
+	enum isp_pipeline_stream_state state;
+	wait_queue_head_t wait;
+	atomic_t stopping;
+	spinlock_t lock;
+
+	struct {
+		struct v4l2_rect request;
+		struct v4l2_rect active;
+	} crop;
+};
+
+struct isp_device;
+
+int omap3isp_resizer_init(struct isp_device *isp);
+void omap3isp_resizer_cleanup(struct isp_device *isp);
+
+int omap3isp_resizer_register_entities(struct isp_res_device *res,
+				       struct v4l2_device *vdev);
+void omap3isp_resizer_unregister_entities(struct isp_res_device *res);
+void omap3isp_resizer_isr_frame_sync(struct isp_res_device *res);
+void omap3isp_resizer_isr(struct isp_res_device *isp_res);
+
+void omap3isp_resizer_max_rate(struct isp_res_device *res,
+			       unsigned int *max_rate);
+
+void omap3isp_resizer_suspend(struct isp_res_device *isp_res);
+
+void omap3isp_resizer_resume(struct isp_res_device *isp_res);
+
+int omap3isp_resizer_busy(struct isp_res_device *isp_res);
+
+#endif	/* OMAP3_ISP_RESIZER_H */

linux-7.2.3/drivers/media/platform/ti/omap3isp/ispstat.h

@@ -0,0 +1,153 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * ispstat.h
+ *
+ * TI OMAP3 ISP - Statistics core
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc
+ *
+ * Contacts: David Cohen <dacohen@gmail.com>
+ *	     Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#ifndef OMAP3_ISP_STAT_H
+#define OMAP3_ISP_STAT_H
+
+#include <linux/types.h>
+#include <linux/omap3isp.h>
+#include <media/v4l2-event.h>
+
+#include "isp.h"
+#include "ispvideo.h"
+
+#define STAT_MAX_BUFS		5
+#define STAT_NEVENTS		8
+
+#define STAT_BUF_DONE		0	/* Buffer is ready */
+#define STAT_NO_BUF		1	/* An error has occurred */
+#define STAT_BUF_WAITING_DMA	2	/* Histogram only: DMA is running */
+
+struct dma_chan;
+struct ispstat;
+
+struct ispstat_buffer {
+	struct sg_table sgt;
+	void *virt_addr;
+	dma_addr_t dma_addr;
+	struct timespec64 ts;
+	u32 buf_size;
+	u32 frame_number;
+	u16 config_counter;
+	u8 empty;
+};
+
+struct ispstat_ops {
+	/*
+	 * Validate new params configuration.
+	 * new_conf->buf_size value must be changed to the exact buffer size
+	 * necessary for the new configuration if it's smaller.
+	 */
+	int (*validate_params)(struct ispstat *stat, void *new_conf);
+
+	/*
+	 * Save new params configuration.
+	 * stat->priv->buf_size value must be set to the exact buffer size for
+	 * the new configuration.
+	 * stat->update is set to 1 if new configuration is different than
+	 * current one.
+	 */
+	void (*set_params)(struct ispstat *stat, void *new_conf);
+
+	/* Apply stored configuration. */
+	void (*setup_regs)(struct ispstat *stat, void *priv);
+
+	/* Enable/Disable module. */
+	void (*enable)(struct ispstat *stat, int enable);
+
+	/* Verify is module is busy. */
+	int (*busy)(struct ispstat *stat);
+
+	/* Used for specific operations during generic buf process task. */
+	int (*buf_process)(struct ispstat *stat);
+};
+
+enum ispstat_state_t {
+	ISPSTAT_DISABLED = 0,
+	ISPSTAT_DISABLING,
+	ISPSTAT_ENABLED,
+	ISPSTAT_ENABLING,
+	ISPSTAT_SUSPENDED,
+};
+
+struct ispstat {
+	struct v4l2_subdev subdev;
+	struct media_pad pad;	/* sink pad */
+
+	/* Control */
+	unsigned configured:1;
+	unsigned update:1;
+	unsigned buf_processing:1;
+	unsigned sbl_ovl_recover:1;
+	u8 inc_config;
+	atomic_t buf_err;
+	enum ispstat_state_t state;	/* enabling/disabling state */
+	struct isp_device *isp;
+	void *priv;		/* pointer to priv config struct */
+	void *recover_priv;	/* pointer to recover priv configuration */
+	struct mutex ioctl_lock; /* serialize private ioctl */
+
+	const struct ispstat_ops *ops;
+
+	/* Buffer */
+	u8 wait_acc_frames;
+	u16 config_counter;
+	u32 frame_number;
+	u32 buf_size;
+	u32 buf_alloc_size;
+	struct dma_chan *dma_ch;
+	unsigned long event_type;
+	struct ispstat_buffer *buf;
+	struct ispstat_buffer *active_buf;
+	struct ispstat_buffer *locked_buf;
+};
+
+struct ispstat_generic_config {
+	/*
+	 * Fields must be in the same order as in:
+	 *  - omap3isp_h3a_aewb_config
+	 *  - omap3isp_h3a_af_config
+	 *  - omap3isp_hist_config
+	 */
+	u32 buf_size;
+	u16 config_counter;
+};
+
+int omap3isp_stat_config(struct ispstat *stat, void *new_conf);
+int omap3isp_stat_request_statistics(struct ispstat *stat,
+				     struct omap3isp_stat_data *data);
+int omap3isp_stat_request_statistics_time32(struct ispstat *stat,
+				     struct omap3isp_stat_data_time32 *data);
+int omap3isp_stat_init(struct ispstat *stat, const char *name,
+		       const struct v4l2_subdev_ops *sd_ops);
+void omap3isp_stat_cleanup(struct ispstat *stat);
+int omap3isp_stat_subscribe_event(struct v4l2_subdev *subdev,
+				  struct v4l2_fh *fh,
+				  struct v4l2_event_subscription *sub);
+int omap3isp_stat_s_stream(struct v4l2_subdev *subdev, int enable);
+
+int omap3isp_stat_busy(struct ispstat *stat);
+int omap3isp_stat_pcr_busy(struct ispstat *stat);
+void omap3isp_stat_suspend(struct ispstat *stat);
+void omap3isp_stat_resume(struct ispstat *stat);
+int omap3isp_stat_enable(struct ispstat *stat, u8 enable);
+void omap3isp_stat_sbl_overflow(struct ispstat *stat);
+void omap3isp_stat_isr(struct ispstat *stat);
+void omap3isp_stat_isr_frame_sync(struct ispstat *stat);
+void omap3isp_stat_dma_isr(struct ispstat *stat);
+int omap3isp_stat_register_entities(struct ispstat *stat,
+				    struct v4l2_device *vdev);
+void omap3isp_stat_unregister_entities(struct ispstat *stat);
+
+#endif /* OMAP3_ISP_STAT_H */

linux-7.2.3/drivers/media/platform/ti/omap3isp/ispvideo.h

@@ -0,0 +1,218 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * ispvideo.h
+ *
+ * TI OMAP3 ISP - Generic video node
+ *
+ * Copyright (C) 2009-2010 Nokia Corporation
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#ifndef OMAP3_ISP_VIDEO_H
+#define OMAP3_ISP_VIDEO_H
+
+#include <linux/v4l2-mediabus.h>
+#include <media/media-entity.h>
+#include <media/v4l2-dev.h>
+#include <media/v4l2-fh.h>
+#include <media/videobuf2-v4l2.h>
+
+#define ISP_VIDEO_DRIVER_NAME		"ispvideo"
+#define ISP_VIDEO_DRIVER_VERSION	"0.0.2"
+
+struct isp_device;
+struct isp_video;
+struct v4l2_mbus_framefmt;
+struct v4l2_pix_format;
+
+/*
+ * struct isp_format_info - ISP media bus format information
+ * @code: V4L2 media bus format code
+ * @truncated: V4L2 media bus format code for the same format truncated to 10
+ *	bits. Identical to @code if the format is 10 bits wide or less.
+ * @uncompressed: V4L2 media bus format code for the corresponding uncompressed
+ *	format. Identical to @code if the format is not DPCM compressed.
+ * @flavor: V4L2 media bus format code for the same pixel layout but
+ *	shifted to be 8 bits per pixel. =0 if format is not shiftable.
+ * @pixelformat: V4L2 pixel format FCC identifier
+ * @width: Bits per pixel (when transferred over a bus)
+ * @bpp: Bytes per pixel (when stored in memory)
+ */
+struct isp_format_info {
+	u32 code;
+	u32 truncated;
+	u32 uncompressed;
+	u32 flavor;
+	u32 pixelformat;
+	unsigned int width;
+	unsigned int bpp;
+};
+
+enum isp_pipeline_stream_state {
+	ISP_PIPELINE_STREAM_STOPPED = 0,
+	ISP_PIPELINE_STREAM_CONTINUOUS = 1,
+	ISP_PIPELINE_STREAM_SINGLESHOT = 2,
+};
+
+enum isp_pipeline_state {
+	/* The stream has been started on the input video node. */
+	ISP_PIPELINE_STREAM_INPUT = 1,
+	/* The stream has been started on the output video node. */
+	ISP_PIPELINE_STREAM_OUTPUT = 2,
+	/* At least one buffer is queued on the input video node. */
+	ISP_PIPELINE_QUEUE_INPUT = 4,
+	/* At least one buffer is queued on the output video node. */
+	ISP_PIPELINE_QUEUE_OUTPUT = 8,
+	/* The input entity is idle, ready to be started. */
+	ISP_PIPELINE_IDLE_INPUT = 16,
+	/* The output entity is idle, ready to be started. */
+	ISP_PIPELINE_IDLE_OUTPUT = 32,
+	/* The pipeline is currently streaming. */
+	ISP_PIPELINE_STREAM = 64,
+};
+
+/*
+ * struct isp_pipeline - An ISP hardware pipeline
+ * @field: The field being processed by the pipeline
+ * @error: A hardware error occurred during capture
+ * @ent_enum: Entities in the pipeline
+ */
+struct isp_pipeline {
+	struct media_pipeline pipe;
+	spinlock_t lock;		/* Pipeline state and queue flags */
+	unsigned int state;
+	enum isp_pipeline_stream_state stream_state;
+	struct isp_video *input;
+	struct isp_video *output;
+	struct media_entity_enum ent_enum;
+	unsigned long l3_ick;
+	unsigned int max_rate;
+	enum v4l2_field field;
+	atomic_t frame_number;
+	bool do_propagation; /* of frame number */
+	bool error;
+	struct v4l2_fract max_timeperframe;
+	struct v4l2_subdev *external;
+	unsigned int external_rate;
+	unsigned int external_width;
+};
+
+static inline struct isp_pipeline *to_isp_pipeline(struct media_entity *entity)
+{
+	struct media_pipeline *pipe = media_entity_pipeline(entity);
+
+	if (!pipe)
+		return NULL;
+
+	return container_of(pipe, struct isp_pipeline, pipe);
+}
+
+static inline int isp_pipeline_ready(struct isp_pipeline *pipe)
+{
+	return pipe->state == (ISP_PIPELINE_STREAM_INPUT |
+			       ISP_PIPELINE_STREAM_OUTPUT |
+			       ISP_PIPELINE_QUEUE_INPUT |
+			       ISP_PIPELINE_QUEUE_OUTPUT |
+			       ISP_PIPELINE_IDLE_INPUT |
+			       ISP_PIPELINE_IDLE_OUTPUT);
+}
+
+/**
+ * struct isp_buffer - ISP video buffer
+ * @vb: videobuf2 buffer
+ * @irqlist: List head for insertion into IRQ queue
+ * @dma: DMA address
+ */
+struct isp_buffer {
+	struct vb2_v4l2_buffer vb;
+	struct list_head irqlist;
+	dma_addr_t dma;
+};
+
+#define to_isp_buffer(buf)	container_of(buf, struct isp_buffer, vb)
+
+enum isp_video_dmaqueue_flags {
+	/* Set if DMA queue becomes empty when ISP_PIPELINE_STREAM_CONTINUOUS */
+	ISP_VIDEO_DMAQUEUE_UNDERRUN = (1 << 0),
+	/* Set when queuing buffer to an empty DMA queue */
+	ISP_VIDEO_DMAQUEUE_QUEUED = (1 << 1),
+};
+
+#define isp_video_dmaqueue_flags_clr(video)	\
+			({ (video)->dmaqueue_flags = 0; })
+
+/*
+ * struct isp_video_operations - ISP video operations
+ * @queue:	Resume streaming when a buffer is queued. Called on VIDIOC_QBUF
+ *		if there was no buffer previously queued.
+ */
+struct isp_video_operations {
+	int(*queue)(struct isp_video *video, struct isp_buffer *buffer);
+};
+
+struct isp_video {
+	struct video_device video;
+	enum v4l2_buf_type type;
+	struct media_pad pad;
+
+	struct mutex mutex;		/* format and crop settings */
+	atomic_t active;
+
+	struct isp_device *isp;
+
+	unsigned int capture_mem;
+	unsigned int bpl_alignment;	/* alignment value */
+	unsigned int bpl_zero_padding;	/* whether the alignment is optional */
+	unsigned int bpl_max;		/* maximum bytes per line value */
+	unsigned int bpl_value;		/* bytes per line value */
+	unsigned int bpl_padding;	/* padding at end of line */
+
+	/* Pipeline state */
+	struct isp_pipeline pipe;
+	struct mutex stream_lock;	/* pipeline and stream states */
+	bool error;
+
+	/* Video buffers queue */
+	struct vb2_queue *queue;
+	struct mutex queue_lock;	/* protects the queue */
+	spinlock_t irqlock;		/* protects dmaqueue */
+	struct list_head dmaqueue;
+	enum isp_video_dmaqueue_flags dmaqueue_flags;
+
+	const struct isp_video_operations *ops;
+};
+
+#define to_isp_video(vdev)	container_of(vdev, struct isp_video, video)
+
+struct isp_video_fh {
+	struct v4l2_fh vfh;
+	struct isp_video *video;
+	struct vb2_queue queue;
+	struct v4l2_format format;
+	struct v4l2_fract timeperframe;
+};
+
+static inline struct isp_video_fh *file_to_isp_video_fh(struct file *filp)
+{
+	return container_of(file_to_v4l2_fh(filp), struct isp_video_fh, vfh);
+}
+
+#define isp_video_queue_to_isp_video_fh(q) \
+				container_of(q, struct isp_video_fh, queue)
+
+int omap3isp_video_init(struct isp_video *video, const char *name);
+void omap3isp_video_cleanup(struct isp_video *video);
+int omap3isp_video_register(struct isp_video *video,
+			    struct v4l2_device *vdev);
+void omap3isp_video_unregister(struct isp_video *video);
+struct isp_buffer *omap3isp_video_buffer_next(struct isp_video *video);
+void omap3isp_video_cancel_stream(struct isp_video *video);
+void omap3isp_video_resume(struct isp_video *video, int continuous);
+struct media_pad *omap3isp_video_remote_pad(struct isp_video *video);
+
+const struct isp_format_info *
+omap3isp_video_format_info(u32 code);
+
+#endif /* OMAP3_ISP_VIDEO_H */

linux-7.2.3/drivers/media/platform/ti/omap3isp/luma_enhance_table.h

@@ -0,0 +1,29 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * luma_enhance_table.h
+ *
+ * TI OMAP3 ISP - Luminance enhancement table
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+1047552, 1047552, 1047552, 1047552, 1047552, 1047552, 1047552, 1047552,
+1047552, 1047552, 1047552, 1047552, 1047552, 1047552, 1047552, 1047552,
+1047552, 1047552, 1047552, 1047552, 1047552, 1047552, 1047552, 1047552,
+1047552, 1047552, 1047552, 1047552, 1048575, 1047551, 1046527, 1045503,
+1044479, 1043455, 1042431, 1041407, 1040383, 1039359, 1038335, 1037311,
+1036287, 1035263, 1034239, 1033215, 1032191, 1031167, 1030143, 1028096,
+1028096, 1028096, 1028096, 1028096, 1028096, 1028096, 1028096, 1028096,
+1028096, 1028100, 1032196, 1036292, 1040388, 1044484,       0,       0,
+      0,       5,    5125,   10245,   15365,   20485,   25605,   30720,
+  30720,   30720,   30720,   30720,   30720,   30720,   30720,   30720,
+  30720,   30720,   31743,   30719,   29695,   28671,   27647,   26623,
+  25599,   24575,   23551,   22527,   21503,   20479,   19455,   18431,
+  17407,   16383,   15359,   14335,   13311,   12287,   11263,   10239,
+   9215,    8191,    7167,    6143,    5119,    4095,    3071,    1024,
+   1024,    1024,    1024,    1024,    1024,    1024,    1024,    1024,
+   1024,    1024,    1024,    1024,    1024,    1024,    1024,    1024

linux-7.2.3/drivers/media/platform/ti/omap3isp/noise_filter_table.h

@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * noise_filter_table.h
+ *
+ * TI OMAP3 ISP - Noise filter table
+ *
+ * Copyright (C) 2010 Nokia Corporation
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16,
+16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16, 16,
+31, 31, 31, 31, 31, 31, 31, 31, 31, 31, 31, 31, 31, 31, 31, 31,
+31, 31, 31, 31, 31, 31, 31, 31, 31, 31, 31, 31, 31, 31, 31, 31

linux-7.2.3/drivers/media/platform/ti/omap3isp/omap3isp.h

@@ -0,0 +1,132 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * omap3isp.h
+ *
+ * TI OMAP3 ISP - Bus Configuration
+ *
+ * Copyright (C) 2011 Nokia Corporation
+ *
+ * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	     Sakari Ailus <sakari.ailus@iki.fi>
+ */
+
+#ifndef __OMAP3ISP_H__
+#define __OMAP3ISP_H__
+
+enum isp_interface_type {
+	ISP_INTERFACE_PARALLEL,
+	ISP_INTERFACE_CSI2A_PHY2,
+	ISP_INTERFACE_CCP2B_PHY1,
+	ISP_INTERFACE_CCP2B_PHY2,
+	ISP_INTERFACE_CSI2C_PHY1,
+};
+
+/**
+ * struct isp_parallel_cfg - Parallel interface configuration
+ * @data_lane_shift: Data lane shifter
+ *		0 - CAMEXT[13:0] -> CAM[13:0]
+ *		2 - CAMEXT[13:2] -> CAM[11:0]
+ *		4 - CAMEXT[13:4] -> CAM[9:0]
+ *		6 - CAMEXT[13:6] -> CAM[7:0]
+ * @clk_pol: Pixel clock polarity
+ *		0 - Sample on rising edge, 1 - Sample on falling edge
+ * @hs_pol: Horizontal synchronization polarity
+ *		0 - Active high, 1 - Active low
+ * @vs_pol: Vertical synchronization polarity
+ *		0 - Active high, 1 - Active low
+ * @fld_pol: Field signal polarity
+ *		0 - Positive, 1 - Negative
+ * @data_pol: Data polarity
+ *		0 - Normal, 1 - One's complement
+ * @bt656: Data contain BT.656 embedded synchronization
+ */
+struct isp_parallel_cfg {
+	unsigned int data_lane_shift:3;
+	unsigned int clk_pol:1;
+	unsigned int hs_pol:1;
+	unsigned int vs_pol:1;
+	unsigned int fld_pol:1;
+	unsigned int data_pol:1;
+	unsigned int bt656:1;
+};
+
+enum {
+	ISP_CCP2_PHY_DATA_CLOCK = 0,
+	ISP_CCP2_PHY_DATA_STROBE = 1,
+};
+
+enum {
+	ISP_CCP2_MODE_MIPI = 0,
+	ISP_CCP2_MODE_CCP2 = 1,
+};
+
+/**
+ * struct isp_csiphy_lane: CCP2/CSI2 lane position and polarity
+ * @pos: position of the lane
+ * @pol: polarity of the lane
+ */
+struct isp_csiphy_lane {
+	u8 pos;
+	u8 pol;
+};
+
+#define ISP_CSIPHY1_NUM_DATA_LANES	1
+#define ISP_CSIPHY2_NUM_DATA_LANES	2
+
+/**
+ * struct isp_csiphy_lanes_cfg - CCP2/CSI2 lane configuration
+ * @data: Configuration of one or two data lanes
+ * @clk: Clock lane configuration
+ */
+struct isp_csiphy_lanes_cfg {
+	struct isp_csiphy_lane data[ISP_CSIPHY2_NUM_DATA_LANES];
+	struct isp_csiphy_lane clk;
+};
+
+/**
+ * struct isp_ccp2_cfg - CCP2 interface configuration
+ * @strobe_clk_pol: Strobe/clock polarity
+ *		0 - Non Inverted, 1 - Inverted
+ * @crc: Enable the cyclic redundancy check
+ * @ccp2_mode: Enable CCP2 compatibility mode
+ *		ISP_CCP2_MODE_MIPI - MIPI-CSI1 mode
+ *		ISP_CCP2_MODE_CCP2 - CCP2 mode
+ * @phy_layer: Physical layer selection
+ *		ISP_CCP2_PHY_DATA_CLOCK - Data/clock physical layer
+ *		ISP_CCP2_PHY_DATA_STROBE - Data/strobe physical layer
+ * @vpclk_div: Video port output clock control
+ * @vp_clk_pol: Video port output clock polarity
+ * @lanecfg: CCP2/CSI2 lane configuration
+ */
+struct isp_ccp2_cfg {
+	unsigned int strobe_clk_pol:1;
+	unsigned int crc:1;
+	unsigned int ccp2_mode:1;
+	unsigned int phy_layer:1;
+	unsigned int vpclk_div:2;
+	unsigned int vp_clk_pol:1;
+	struct isp_csiphy_lanes_cfg lanecfg;
+};
+
+/**
+ * struct isp_csi2_cfg - CSI2 interface configuration
+ * @crc: Enable the cyclic redundancy check
+ * @lanecfg: CSI-2 lane configuration
+ * @num_data_lanes: The number of data lanes in use
+ */
+struct isp_csi2_cfg {
+	unsigned crc:1;
+	struct isp_csiphy_lanes_cfg lanecfg;
+	u8 num_data_lanes;
+};
+
+struct isp_bus_cfg {
+	enum isp_interface_type interface;
+	union {
+		struct isp_parallel_cfg parallel;
+		struct isp_ccp2_cfg ccp2;
+		struct isp_csi2_cfg csi2;
+	} bus; /* gcc < 4.6.0 chokes on anonymous union initializers */
+};
+
+#endif	/* __OMAP3ISP_H__ */

linux-7.2.3/drivers/media/platform/ti/vpe/Makefile

@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_VIDEO_TI_VPE) += ti-vpe.o
+obj-$(CONFIG_VIDEO_TI_VPDMA) += ti-vpdma.o
+obj-$(CONFIG_VIDEO_TI_SC) += ti-sc.o
+obj-$(CONFIG_VIDEO_TI_CSC) += ti-csc.o
+obj-$(CONFIG_VIDEO_TI_VIP) += ti-vip.o
+
+ti-vpe-y := vpe.o
+ti-vpdma-y := vpdma.o
+ti-sc-y := sc.o
+ti-csc-y := csc.o
+ti-vip-y := vip.o
+
+ccflags-$(CONFIG_VIDEO_TI_VPE_DEBUG) += -DDEBUG

linux-7.2.3/drivers/media/platform/ti/vpe/csc.c

@@ -0,0 +1,279 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Color space converter library
+ *
+ * Copyright (c) 2013 Texas Instruments Inc.
+ *
+ * David Griego, <dagriego@biglakesoftware.com>
+ * Dale Farnsworth, <dale@farnsworth.org>
+ * Archit Taneja, <archit@ti.com>
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/videodev2.h>
+#include <media/v4l2-common.h>
+
+#include "csc.h"
+
+/*
+ * 12 coefficients in the order:
+ * a0, b0, c0, a1, b1, c1, a2, b2, c2, d0, d1, d2
+ */
+struct quantization {
+	u16	coeff[12];
+};
+
+struct colorspace {
+	struct quantization limited;
+	struct quantization full;
+};
+
+struct encoding_direction {
+	struct colorspace r601;
+	struct colorspace r709;
+};
+
+struct csc_coeffs {
+	struct encoding_direction y2r;
+	struct encoding_direction r2y;
+};
+
+/* default colorspace coefficients */
+static struct csc_coeffs csc_coeffs = {
+	.y2r = {
+		.r601 = {
+			.limited = {
+				{	/* SDTV */
+				0x0400, 0x0000, 0x057D, 0x0400, 0x1EA7, 0x1D35,
+				0x0400, 0x06EF, 0x1FFE, 0x0D40, 0x0210, 0x0C88,
+				}
+			},
+			.full = {
+				{	/* SDTV */
+				0x04A8, 0x1FFE, 0x0662, 0x04A8, 0x1E6F, 0x1CBF,
+				0x04A8, 0x0812, 0x1FFF, 0x0C84, 0x0220, 0x0BAC,
+				}
+			},
+		},
+		.r709 = {
+			.limited = {
+				{	/* HDTV */
+				0x0400, 0x0000, 0x0629, 0x0400, 0x1F45, 0x1E2B,
+				0x0400, 0x0742, 0x0000, 0x0CEC, 0x0148, 0x0C60,
+				}
+			},
+			.full = {
+				{	/* HDTV */
+				0x04A8, 0x0000, 0x072C, 0x04A8, 0x1F26, 0x1DDE,
+				0x04A8, 0x0873, 0x0000, 0x0C20, 0x0134, 0x0B7C,
+				}
+			},
+		},
+	},
+	.r2y = {
+		.r601 = {
+			.limited = {
+				{	/* SDTV */
+				0x0132, 0x0259, 0x0075, 0x1F50, 0x1EA5, 0x020B,
+				0x020B, 0x1E4A, 0x1FAB, 0x0000, 0x0200, 0x0200,
+				}
+			},
+			.full = {
+				{	/* SDTV */
+				0x0107, 0x0204, 0x0064, 0x1F68, 0x1ED6, 0x01C2,
+				0x01C2, 0x1E87, 0x1FB7, 0x0040, 0x0200, 0x0200,
+				}
+			},
+		},
+		.r709 = {
+			.limited = {
+				{	/* HDTV */
+				0x00DA, 0x02DC, 0x004A, 0x1F88, 0x1E6C, 0x020C,
+				0x020C, 0x1E24, 0x1FD0, 0x0000, 0x0200, 0x0200,
+				}
+			},
+			.full = {
+				{	/* HDTV */
+				0x00bb, 0x0275, 0x003f, 0x1f99, 0x1ea5, 0x01c2,
+				0x01c2, 0x1e67, 0x1fd7, 0x0040, 0x0200, 0x0200,
+				}
+			},
+		},
+	},
+
+};
+
+void csc_dump_regs(struct csc_data *csc)
+{
+	struct device *dev = &csc->pdev->dev;
+
+#define DUMPREG(r) dev_dbg(dev, "%-35s %08x\n", #r, \
+	ioread32(csc->base + CSC_##r))
+
+	dev_dbg(dev, "CSC Registers @ %pa:\n", &csc->res->start);
+
+	DUMPREG(CSC00);
+	DUMPREG(CSC01);
+	DUMPREG(CSC02);
+	DUMPREG(CSC03);
+	DUMPREG(CSC04);
+	DUMPREG(CSC05);
+
+#undef DUMPREG
+}
+EXPORT_SYMBOL(csc_dump_regs);
+
+void csc_set_coeff_bypass(struct csc_data *csc, u32 *csc_reg5)
+{
+	*csc_reg5 |= CSC_BYPASS;
+}
+EXPORT_SYMBOL(csc_set_coeff_bypass);
+
+/*
+ * set the color space converter coefficient shadow register values
+ */
+void csc_set_coeff(struct csc_data *csc, u32 *csc_reg0,
+		   struct v4l2_format *src_fmt, struct v4l2_format *dst_fmt)
+{
+	u32 *csc_reg5 = csc_reg0 + 5;
+	u32 *shadow_csc = csc_reg0;
+	u16 *coeff, *end_coeff;
+	const struct v4l2_pix_format *pix;
+	const struct v4l2_pix_format_mplane *mp;
+	const struct v4l2_format_info *src_finfo, *dst_finfo;
+	enum v4l2_ycbcr_encoding src_ycbcr_enc, dst_ycbcr_enc;
+	enum v4l2_quantization src_quantization, dst_quantization;
+	u32 src_pixelformat, dst_pixelformat;
+
+	if (V4L2_TYPE_IS_MULTIPLANAR(src_fmt->type)) {
+		mp = &src_fmt->fmt.pix_mp;
+		src_pixelformat = mp->pixelformat;
+		src_ycbcr_enc = mp->ycbcr_enc;
+		src_quantization = mp->quantization;
+	} else {
+		pix = &src_fmt->fmt.pix;
+		src_pixelformat = pix->pixelformat;
+		src_ycbcr_enc = pix->ycbcr_enc;
+		src_quantization = pix->quantization;
+	}
+
+	if (V4L2_TYPE_IS_MULTIPLANAR(dst_fmt->type)) {
+		mp = &dst_fmt->fmt.pix_mp;
+		dst_pixelformat = mp->pixelformat;
+		dst_ycbcr_enc = mp->ycbcr_enc;
+		dst_quantization = mp->quantization;
+	} else {
+		pix = &dst_fmt->fmt.pix;
+		dst_pixelformat = pix->pixelformat;
+		dst_ycbcr_enc = pix->ycbcr_enc;
+		dst_quantization = pix->quantization;
+	}
+
+	src_finfo = v4l2_format_info(src_pixelformat);
+	dst_finfo = v4l2_format_info(dst_pixelformat);
+
+	if (v4l2_is_format_yuv(src_finfo) &&
+	    v4l2_is_format_rgb(dst_finfo)) {
+		/* Y2R */
+
+		/*
+		 * These are not the standard default values but are
+		 * set this way for historical compatibility
+		 */
+		if (src_ycbcr_enc == V4L2_YCBCR_ENC_DEFAULT)
+			src_ycbcr_enc = V4L2_YCBCR_ENC_601;
+
+		if (src_quantization == V4L2_QUANTIZATION_DEFAULT)
+			src_quantization = V4L2_QUANTIZATION_FULL_RANGE;
+
+		if (src_ycbcr_enc == V4L2_YCBCR_ENC_601) {
+			if (src_quantization == V4L2_QUANTIZATION_FULL_RANGE)
+				coeff = csc_coeffs.y2r.r601.full.coeff;
+			else
+				coeff = csc_coeffs.y2r.r601.limited.coeff;
+		} else if (src_ycbcr_enc == V4L2_YCBCR_ENC_709) {
+			if (src_quantization == V4L2_QUANTIZATION_FULL_RANGE)
+				coeff = csc_coeffs.y2r.r709.full.coeff;
+			else
+				coeff = csc_coeffs.y2r.r709.limited.coeff;
+		} else {
+			/* Should never reach this, but it keeps gcc happy */
+			coeff = csc_coeffs.y2r.r601.full.coeff;
+		}
+	} else if (v4l2_is_format_rgb(src_finfo) &&
+		   v4l2_is_format_yuv(dst_finfo)) {
+		/* R2Y */
+
+		/*
+		 * These are not the standard default values but are
+		 * set this way for historical compatibility
+		 */
+		if (dst_ycbcr_enc == V4L2_YCBCR_ENC_DEFAULT)
+			dst_ycbcr_enc = V4L2_YCBCR_ENC_601;
+
+		if (dst_quantization == V4L2_QUANTIZATION_DEFAULT)
+			dst_quantization = V4L2_QUANTIZATION_FULL_RANGE;
+
+		if (dst_ycbcr_enc == V4L2_YCBCR_ENC_601) {
+			if (dst_quantization == V4L2_QUANTIZATION_FULL_RANGE)
+				coeff = csc_coeffs.r2y.r601.full.coeff;
+			else
+				coeff = csc_coeffs.r2y.r601.limited.coeff;
+		} else if (dst_ycbcr_enc == V4L2_YCBCR_ENC_709) {
+			if (dst_quantization == V4L2_QUANTIZATION_FULL_RANGE)
+				coeff = csc_coeffs.r2y.r709.full.coeff;
+			else
+				coeff = csc_coeffs.r2y.r709.limited.coeff;
+		} else {
+			/* Should never reach this, but it keeps gcc happy */
+			coeff = csc_coeffs.r2y.r601.full.coeff;
+		}
+	} else {
+		*csc_reg5 |= CSC_BYPASS;
+		return;
+	}
+
+	end_coeff = coeff + 12;
+
+	for (; coeff < end_coeff; coeff += 2)
+		*shadow_csc++ = (*(coeff + 1) << 16) | *coeff;
+}
+EXPORT_SYMBOL(csc_set_coeff);
+
+struct csc_data *csc_create(struct platform_device *pdev, const char *res_name)
+{
+	struct csc_data *csc;
+
+	dev_dbg(&pdev->dev, "csc_create\n");
+
+	csc = devm_kzalloc(&pdev->dev, sizeof(*csc), GFP_KERNEL);
+	if (!csc) {
+		dev_err(&pdev->dev, "couldn't alloc csc_data\n");
+		return ERR_PTR(-ENOMEM);
+	}
+
+	csc->pdev = pdev;
+
+	csc->res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						res_name);
+	if (csc->res == NULL) {
+		dev_err(&pdev->dev, "missing '%s' platform resources data\n",
+			res_name);
+		return ERR_PTR(-ENODEV);
+	}
+
+	csc->base = devm_ioremap_resource(&pdev->dev, csc->res);
+	if (IS_ERR(csc->base))
+		return ERR_CAST(csc->base);
+
+	return csc;
+}
+EXPORT_SYMBOL(csc_create);
+
+MODULE_DESCRIPTION("TI VIP/VPE Color Space Converter");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_LICENSE("GPL v2");

linux-7.2.3/drivers/media/platform/ti/vpe/csc.h

@@ -0,0 +1,65 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2013 Texas Instruments Inc.
+ *
+ * David Griego, <dagriego@biglakesoftware.com>
+ * Dale Farnsworth, <dale@farnsworth.org>
+ * Archit Taneja, <archit@ti.com>
+ */
+#ifndef TI_CSC_H
+#define TI_CSC_H
+
+/* VPE color space converter regs */
+#define CSC_CSC00		0x00
+#define CSC_A0_MASK		0x1fff
+#define CSC_A0_SHIFT		0
+#define CSC_B0_MASK		0x1fff
+#define CSC_B0_SHIFT		16
+
+#define CSC_CSC01		0x04
+#define CSC_C0_MASK		0x1fff
+#define CSC_C0_SHIFT		0
+#define CSC_A1_MASK		0x1fff
+#define CSC_A1_SHIFT		16
+
+#define CSC_CSC02		0x08
+#define CSC_B1_MASK		0x1fff
+#define CSC_B1_SHIFT		0
+#define CSC_C1_MASK		0x1fff
+#define CSC_C1_SHIFT		16
+
+#define CSC_CSC03		0x0c
+#define CSC_A2_MASK		0x1fff
+#define CSC_A2_SHIFT		0
+#define CSC_B2_MASK		0x1fff
+#define CSC_B2_SHIFT		16
+
+#define CSC_CSC04		0x10
+#define CSC_C2_MASK		0x1fff
+#define CSC_C2_SHIFT		0
+#define CSC_D0_MASK		0x0fff
+#define CSC_D0_SHIFT		16
+
+#define CSC_CSC05		0x14
+#define CSC_D1_MASK		0x0fff
+#define CSC_D1_SHIFT		0
+#define CSC_D2_MASK		0x0fff
+#define CSC_D2_SHIFT		16
+
+#define CSC_BYPASS		(1 << 28)
+
+struct csc_data {
+	void __iomem		*base;
+	struct resource		*res;
+
+	struct platform_device	*pdev;
+};
+
+void csc_dump_regs(struct csc_data *csc);
+void csc_set_coeff_bypass(struct csc_data *csc, u32 *csc_reg5);
+void csc_set_coeff(struct csc_data *csc, u32 *csc_reg0,
+		   struct v4l2_format *src_fmt, struct v4l2_format *dst_fmt);
+
+struct csc_data *csc_create(struct platform_device *pdev, const char *res_name);
+
+#endif

linux-7.2.3/drivers/media/platform/ti/vpe/sc.c

@@ -0,0 +1,306 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Scaler library
+ *
+ * Copyright (c) 2013 Texas Instruments Inc.
+ *
+ * David Griego, <dagriego@biglakesoftware.com>
+ * Dale Farnsworth, <dale@farnsworth.org>
+ * Archit Taneja, <archit@ti.com>
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include "sc.h"
+#include "sc_coeff.h"
+
+void sc_dump_regs(struct sc_data *sc)
+{
+	struct device *dev = &sc->pdev->dev;
+
+#define DUMPREG(r) dev_dbg(dev, "%-35s %08x\n", #r, \
+	ioread32(sc->base + CFG_##r))
+
+	dev_dbg(dev, "SC Registers @ %pa:\n", &sc->res->start);
+
+	DUMPREG(SC0);
+	DUMPREG(SC1);
+	DUMPREG(SC2);
+	DUMPREG(SC3);
+	DUMPREG(SC4);
+	DUMPREG(SC5);
+	DUMPREG(SC6);
+	DUMPREG(SC8);
+	DUMPREG(SC9);
+	DUMPREG(SC10);
+	DUMPREG(SC11);
+	DUMPREG(SC12);
+	DUMPREG(SC13);
+	DUMPREG(SC17);
+	DUMPREG(SC18);
+	DUMPREG(SC19);
+	DUMPREG(SC20);
+	DUMPREG(SC21);
+	DUMPREG(SC22);
+	DUMPREG(SC23);
+	DUMPREG(SC24);
+	DUMPREG(SC25);
+
+#undef DUMPREG
+}
+EXPORT_SYMBOL(sc_dump_regs);
+
+/*
+ * set the horizontal scaler coefficients according to the ratio of output to
+ * input widths, after accounting for up to two levels of decimation
+ */
+void sc_set_hs_coeffs(struct sc_data *sc, void *addr, unsigned int src_w,
+		unsigned int dst_w)
+{
+	int sixteenths;
+	int idx;
+	int i, j;
+	u16 *coeff_h = addr;
+	const u16 *cp;
+
+	if (dst_w > src_w) {
+		idx = HS_UP_SCALE;
+	} else {
+		if ((dst_w << 1) < src_w)
+			dst_w <<= 1;	/* first level decimation */
+		if ((dst_w << 1) < src_w)
+			dst_w <<= 1;	/* second level decimation */
+
+		if (dst_w == src_w) {
+			idx = HS_LE_16_16_SCALE;
+		} else {
+			sixteenths = (dst_w << 4) / src_w;
+			if (sixteenths < 8)
+				sixteenths = 8;
+			idx = HS_LT_9_16_SCALE + sixteenths - 8;
+		}
+	}
+
+	cp = scaler_hs_coeffs[idx];
+
+	for (i = 0; i < SC_NUM_PHASES * 2; i++) {
+		for (j = 0; j < SC_H_NUM_TAPS; j++)
+			*coeff_h++ = *cp++;
+		/*
+		 * for each phase, the scaler expects space for 8 coefficients
+		 * in it's memory. For the horizontal scaler, we copy the first
+		 * 7 coefficients and skip the last slot to move to the next
+		 * row to hold coefficients for the next phase
+		 */
+		coeff_h += SC_NUM_TAPS_MEM_ALIGN - SC_H_NUM_TAPS;
+	}
+
+	sc->load_coeff_h = true;
+}
+EXPORT_SYMBOL(sc_set_hs_coeffs);
+
+/*
+ * set the vertical scaler coefficients according to the ratio of output to
+ * input heights
+ */
+void sc_set_vs_coeffs(struct sc_data *sc, void *addr, unsigned int src_h,
+		unsigned int dst_h)
+{
+	int sixteenths;
+	int idx;
+	int i, j;
+	u16 *coeff_v = addr;
+	const u16 *cp;
+
+	if (dst_h > src_h) {
+		idx = VS_UP_SCALE;
+	} else if (dst_h == src_h) {
+		idx = VS_1_TO_1_SCALE;
+	} else {
+		sixteenths = (dst_h << 4) / src_h;
+		if (sixteenths < 8)
+			sixteenths = 8;
+		idx = VS_LT_9_16_SCALE + sixteenths - 8;
+	}
+
+	cp = scaler_vs_coeffs[idx];
+
+	for (i = 0; i < SC_NUM_PHASES * 2; i++) {
+		for (j = 0; j < SC_V_NUM_TAPS; j++)
+			*coeff_v++ = *cp++;
+		/*
+		 * for the vertical scaler, we copy the first 5 coefficients and
+		 * skip the last 3 slots to move to the next row to hold
+		 * coefficients for the next phase
+		 */
+		coeff_v += SC_NUM_TAPS_MEM_ALIGN - SC_V_NUM_TAPS;
+	}
+
+	sc->load_coeff_v = true;
+}
+EXPORT_SYMBOL(sc_set_vs_coeffs);
+
+void sc_config_scaler(struct sc_data *sc, u32 *sc_reg0, u32 *sc_reg8,
+		u32 *sc_reg17, unsigned int src_w, unsigned int src_h,
+		unsigned int dst_w, unsigned int dst_h)
+{
+	struct device *dev = &sc->pdev->dev;
+	u32 val;
+	int dcm_x, dcm_shift;
+	bool use_rav;
+	unsigned long lltmp;
+	u32 lin_acc_inc, lin_acc_inc_u;
+	u32 col_acc_offset;
+	u16 factor = 0;
+	int row_acc_init_rav = 0, row_acc_init_rav_b = 0;
+	u32 row_acc_inc = 0, row_acc_offset = 0, row_acc_offset_b = 0;
+	/*
+	 * location of SC register in payload memory with respect to the first
+	 * register in the mmr address data block
+	 */
+	u32 *sc_reg9 = sc_reg8 + 1;
+	u32 *sc_reg12 = sc_reg8 + 4;
+	u32 *sc_reg13 = sc_reg8 + 5;
+	u32 *sc_reg24 = sc_reg17 + 7;
+
+	val = sc_reg0[0];
+
+	/* clear all the features(they may get enabled elsewhere later) */
+	val &= ~(CFG_SELFGEN_FID | CFG_TRIM | CFG_ENABLE_SIN2_VER_INTP |
+		CFG_INTERLACE_I | CFG_DCM_4X | CFG_DCM_2X | CFG_AUTO_HS |
+		CFG_ENABLE_EV | CFG_USE_RAV | CFG_INVT_FID | CFG_SC_BYPASS |
+		CFG_INTERLACE_O | CFG_Y_PK_EN | CFG_HP_BYPASS | CFG_LINEAR);
+
+	if (src_w == dst_w && src_h == dst_h) {
+		val |= CFG_SC_BYPASS;
+		sc_reg0[0] = val;
+		return;
+	}
+
+	/* we only support linear scaling for now */
+	val |= CFG_LINEAR;
+
+	/* configure horizontal scaler */
+
+	/* enable 2X or 4X decimation */
+	dcm_x = src_w / dst_w;
+	if (dcm_x > 4) {
+		val |= CFG_DCM_4X;
+		dcm_shift = 2;
+	} else if (dcm_x > 2) {
+		val |= CFG_DCM_2X;
+		dcm_shift = 1;
+	} else {
+		dcm_shift = 0;
+	}
+
+	lltmp = dst_w - 1;
+	lin_acc_inc = div64_u64(((u64)(src_w >> dcm_shift) - 1) << 24, lltmp);
+	lin_acc_inc_u = 0;
+	col_acc_offset = 0;
+
+	dev_dbg(dev, "hs config: src_w = %d, dst_w = %d, decimation = %s, lin_acc_inc = %08x\n",
+		src_w, dst_w, dcm_shift == 2 ? "4x" :
+		(dcm_shift == 1 ? "2x" : "none"), lin_acc_inc);
+
+	/* configure vertical scaler */
+
+	/* use RAV for vertical scaler if vertical downscaling is > 4x */
+	if (dst_h < (src_h >> 2)) {
+		use_rav = true;
+		val |= CFG_USE_RAV;
+	} else {
+		use_rav = false;
+	}
+
+	if (use_rav) {
+		/* use RAV */
+		factor = (u16) ((dst_h << 10) / src_h);
+
+		row_acc_init_rav = factor + ((1 + factor) >> 1);
+		if (row_acc_init_rav >= 1024)
+			row_acc_init_rav -= 1024;
+
+		row_acc_init_rav_b = row_acc_init_rav +
+				(1 + (row_acc_init_rav >> 1)) -
+				(1024 >> 1);
+
+		if (row_acc_init_rav_b < 0) {
+			row_acc_init_rav_b += row_acc_init_rav;
+			row_acc_init_rav *= 2;
+		}
+
+		dev_dbg(dev, "vs config(RAV): src_h = %d, dst_h = %d, factor = %d, acc_init = %08x, acc_init_b = %08x\n",
+			src_h, dst_h, factor, row_acc_init_rav,
+			row_acc_init_rav_b);
+	} else {
+		/* use polyphase */
+		row_acc_inc = ((src_h - 1) << 16) / (dst_h - 1);
+		row_acc_offset = 0;
+		row_acc_offset_b = 0;
+
+		dev_dbg(dev, "vs config(POLY): src_h = %d, dst_h = %d,row_acc_inc = %08x\n",
+			src_h, dst_h, row_acc_inc);
+	}
+
+
+	sc_reg0[0] = val;
+	sc_reg0[1] = row_acc_inc;
+	sc_reg0[2] = row_acc_offset;
+	sc_reg0[3] = row_acc_offset_b;
+
+	sc_reg0[4] = ((lin_acc_inc_u & CFG_LIN_ACC_INC_U_MASK) <<
+			CFG_LIN_ACC_INC_U_SHIFT) | (dst_w << CFG_TAR_W_SHIFT) |
+			(dst_h << CFG_TAR_H_SHIFT);
+
+	sc_reg0[5] = (src_w << CFG_SRC_W_SHIFT) | (src_h << CFG_SRC_H_SHIFT);
+
+	sc_reg0[6] = (row_acc_init_rav_b << CFG_ROW_ACC_INIT_RAV_B_SHIFT) |
+		(row_acc_init_rav << CFG_ROW_ACC_INIT_RAV_SHIFT);
+
+	*sc_reg9 = lin_acc_inc;
+
+	*sc_reg12 = col_acc_offset << CFG_COL_ACC_OFFSET_SHIFT;
+
+	*sc_reg13 = factor;
+
+	*sc_reg24 = (src_w << CFG_ORG_W_SHIFT) | (src_h << CFG_ORG_H_SHIFT);
+}
+EXPORT_SYMBOL(sc_config_scaler);
+
+struct sc_data *sc_create(struct platform_device *pdev, const char *res_name)
+{
+	struct sc_data *sc;
+
+	dev_dbg(&pdev->dev, "sc_create\n");
+
+	sc = devm_kzalloc(&pdev->dev, sizeof(*sc), GFP_KERNEL);
+	if (!sc) {
+		dev_err(&pdev->dev, "couldn't alloc sc_data\n");
+		return ERR_PTR(-ENOMEM);
+	}
+
+	sc->pdev = pdev;
+
+	sc->res = platform_get_resource_byname(pdev, IORESOURCE_MEM, res_name);
+	if (!sc->res) {
+		dev_err(&pdev->dev, "missing '%s' platform resources data\n",
+			res_name);
+		return ERR_PTR(-ENODEV);
+	}
+
+	sc->base = devm_ioremap_resource(&pdev->dev, sc->res);
+	if (IS_ERR(sc->base))
+		return ERR_CAST(sc->base);
+
+	return sc;
+}
+EXPORT_SYMBOL(sc_create);
+
+MODULE_DESCRIPTION("TI VIP/VPE Scaler");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_LICENSE("GPL v2");

linux-7.2.3/drivers/media/platform/ti/vpe/sc.h

@@ -0,0 +1,208 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2013 Texas Instruments Inc.
+ *
+ * David Griego, <dagriego@biglakesoftware.com>
+ * Dale Farnsworth, <dale@farnsworth.org>
+ * Archit Taneja, <archit@ti.com>
+ */
+#ifndef TI_SC_H
+#define TI_SC_H
+
+/* Scaler regs */
+#define CFG_SC0				0x0
+#define CFG_INTERLACE_O			(1 << 0)
+#define CFG_LINEAR			(1 << 1)
+#define CFG_SC_BYPASS			(1 << 2)
+#define CFG_INVT_FID			(1 << 3)
+#define CFG_USE_RAV			(1 << 4)
+#define CFG_ENABLE_EV			(1 << 5)
+#define CFG_AUTO_HS			(1 << 6)
+#define CFG_DCM_2X			(1 << 7)
+#define CFG_DCM_4X			(1 << 8)
+#define CFG_HP_BYPASS			(1 << 9)
+#define CFG_INTERLACE_I			(1 << 10)
+#define CFG_ENABLE_SIN2_VER_INTP	(1 << 11)
+#define CFG_Y_PK_EN			(1 << 14)
+#define CFG_TRIM			(1 << 15)
+#define CFG_SELFGEN_FID			(1 << 16)
+
+#define CFG_SC1				0x4
+#define CFG_ROW_ACC_INC_MASK		0x07ffffff
+#define CFG_ROW_ACC_INC_SHIFT		0
+
+#define CFG_SC2				0x08
+#define CFG_ROW_ACC_OFFSET_MASK		0x0fffffff
+#define CFG_ROW_ACC_OFFSET_SHIFT	0
+
+#define CFG_SC3				0x0c
+#define CFG_ROW_ACC_OFFSET_B_MASK	0x0fffffff
+#define CFG_ROW_ACC_OFFSET_B_SHIFT	0
+
+#define CFG_SC4				0x10
+#define CFG_TAR_H_MASK			0x07ff
+#define CFG_TAR_H_SHIFT			0
+#define CFG_TAR_W_MASK			0x07ff
+#define CFG_TAR_W_SHIFT			12
+#define CFG_LIN_ACC_INC_U_MASK		0x07
+#define CFG_LIN_ACC_INC_U_SHIFT		24
+#define CFG_NLIN_ACC_INIT_U_MASK	0x07
+#define CFG_NLIN_ACC_INIT_U_SHIFT	28
+
+#define CFG_SC5				0x14
+#define CFG_SRC_H_MASK			0x07ff
+#define CFG_SRC_H_SHIFT			0
+#define CFG_SRC_W_MASK			0x07ff
+#define CFG_SRC_W_SHIFT			12
+#define CFG_NLIN_ACC_INC_U_MASK		0x07
+#define CFG_NLIN_ACC_INC_U_SHIFT	24
+
+#define CFG_SC6				0x18
+#define CFG_ROW_ACC_INIT_RAV_MASK	0x03ff
+#define CFG_ROW_ACC_INIT_RAV_SHIFT	0
+#define CFG_ROW_ACC_INIT_RAV_B_MASK	0x03ff
+#define CFG_ROW_ACC_INIT_RAV_B_SHIFT	10
+
+#define CFG_SC8				0x20
+#define CFG_NLIN_LEFT_MASK		0x07ff
+#define CFG_NLIN_LEFT_SHIFT		0
+#define CFG_NLIN_RIGHT_MASK		0x07ff
+#define CFG_NLIN_RIGHT_SHIFT		12
+
+#define CFG_SC9				0x24
+#define CFG_LIN_ACC_INC			CFG_SC9
+
+#define CFG_SC10			0x28
+#define CFG_NLIN_ACC_INIT		CFG_SC10
+
+#define CFG_SC11			0x2c
+#define CFG_NLIN_ACC_INC		CFG_SC11
+
+#define CFG_SC12			0x30
+#define CFG_COL_ACC_OFFSET_MASK		0x01ffffff
+#define CFG_COL_ACC_OFFSET_SHIFT	0
+
+#define CFG_SC13			0x34
+#define CFG_SC_FACTOR_RAV_MASK		0xff
+#define CFG_SC_FACTOR_RAV_SHIFT		0
+#define CFG_CHROMA_INTP_THR_MASK	0x03ff
+#define CFG_CHROMA_INTP_THR_SHIFT	12
+#define CFG_DELTA_CHROMA_THR_MASK	0x0f
+#define CFG_DELTA_CHROMA_THR_SHIFT	24
+
+#define CFG_SC17			0x44
+#define CFG_EV_THR_MASK			0x03ff
+#define CFG_EV_THR_SHIFT		12
+#define CFG_DELTA_LUMA_THR_MASK		0x0f
+#define CFG_DELTA_LUMA_THR_SHIFT	24
+#define CFG_DELTA_EV_THR_MASK		0x0f
+#define CFG_DELTA_EV_THR_SHIFT		28
+
+#define CFG_SC18			0x48
+#define CFG_HS_FACTOR_MASK		0x03ff
+#define CFG_HS_FACTOR_SHIFT		0
+#define CFG_CONF_DEFAULT_MASK		0x01ff
+#define CFG_CONF_DEFAULT_SHIFT		16
+
+#define CFG_SC19			0x4c
+#define CFG_HPF_COEFF0_MASK		0xff
+#define CFG_HPF_COEFF0_SHIFT		0
+#define CFG_HPF_COEFF1_MASK		0xff
+#define CFG_HPF_COEFF1_SHIFT		8
+#define CFG_HPF_COEFF2_MASK		0xff
+#define CFG_HPF_COEFF2_SHIFT		16
+#define CFG_HPF_COEFF3_MASK		0xff
+#define CFG_HPF_COEFF3_SHIFT		23
+
+#define CFG_SC20			0x50
+#define CFG_HPF_COEFF4_MASK		0xff
+#define CFG_HPF_COEFF4_SHIFT		0
+#define CFG_HPF_COEFF5_MASK		0xff
+#define CFG_HPF_COEFF5_SHIFT		8
+#define CFG_HPF_NORM_SHIFT_MASK		0x07
+#define CFG_HPF_NORM_SHIFT_SHIFT	16
+#define CFG_NL_LIMIT_MASK		0x1ff
+#define CFG_NL_LIMIT_SHIFT		20
+
+#define CFG_SC21			0x54
+#define CFG_NL_LO_THR_MASK		0x01ff
+#define CFG_NL_LO_THR_SHIFT		0
+#define CFG_NL_LO_SLOPE_MASK		0xff
+#define CFG_NL_LO_SLOPE_SHIFT		16
+
+#define CFG_SC22			0x58
+#define CFG_NL_HI_THR_MASK		0x01ff
+#define CFG_NL_HI_THR_SHIFT		0
+#define CFG_NL_HI_SLOPE_SH_MASK		0x07
+#define CFG_NL_HI_SLOPE_SH_SHIFT	16
+
+#define CFG_SC23			0x5c
+#define CFG_GRADIENT_THR_MASK		0x07ff
+#define CFG_GRADIENT_THR_SHIFT		0
+#define CFG_GRADIENT_THR_RANGE_MASK	0x0f
+#define CFG_GRADIENT_THR_RANGE_SHIFT	12
+#define CFG_MIN_GY_THR_MASK		0xff
+#define CFG_MIN_GY_THR_SHIFT		16
+#define CFG_MIN_GY_THR_RANGE_MASK	0x0f
+#define CFG_MIN_GY_THR_RANGE_SHIFT	28
+
+#define CFG_SC24			0x60
+#define CFG_ORG_H_MASK			0x07ff
+#define CFG_ORG_H_SHIFT			0
+#define CFG_ORG_W_MASK			0x07ff
+#define CFG_ORG_W_SHIFT			16
+
+#define CFG_SC25			0x64
+#define CFG_OFF_H_MASK			0x07ff
+#define CFG_OFF_H_SHIFT			0
+#define CFG_OFF_W_MASK			0x07ff
+#define CFG_OFF_W_SHIFT			16
+
+/* number of phases supported by the polyphase scalers */
+#define SC_NUM_PHASES			32
+
+/* number of taps used by horizontal polyphase scaler */
+#define SC_H_NUM_TAPS			7
+
+/* number of taps used by vertical polyphase scaler */
+#define SC_V_NUM_TAPS			5
+
+/* number of taps expected by the scaler in it's coefficient memory */
+#define SC_NUM_TAPS_MEM_ALIGN		8
+
+/* Maximum frame width the scaler can handle (in pixels) */
+#define SC_MAX_PIXEL_WIDTH		2047
+
+/* Maximum frame height the scaler can handle (in lines) */
+#define SC_MAX_PIXEL_HEIGHT		2047
+
+/*
+ * coefficient memory size in bytes:
+ * num phases x num sets(luma and chroma) x num taps(aligned) x coeff size
+ */
+#define SC_COEF_SRAM_SIZE	(SC_NUM_PHASES * 2 * SC_NUM_TAPS_MEM_ALIGN * 2)
+
+struct sc_data {
+	void __iomem		*base;
+	struct resource		*res;
+
+	dma_addr_t		loaded_coeff_h; /* loaded h coeffs in SC */
+	dma_addr_t		loaded_coeff_v; /* loaded v coeffs in SC */
+
+	bool			load_coeff_h;	/* have new h SC coeffs */
+	bool			load_coeff_v;	/* have new v SC coeffs */
+
+	struct platform_device *pdev;
+};
+
+void sc_dump_regs(struct sc_data *sc);
+void sc_set_hs_coeffs(struct sc_data *sc, void *addr, unsigned int src_w,
+		unsigned int dst_w);
+void sc_set_vs_coeffs(struct sc_data *sc, void *addr, unsigned int src_h,
+		unsigned int dst_h);
+void sc_config_scaler(struct sc_data *sc, u32 *sc_reg0, u32 *sc_reg8,
+		u32 *sc_reg17, unsigned int src_w, unsigned int src_h,
+		unsigned int dst_w, unsigned int dst_h);
+struct sc_data *sc_create(struct platform_device *pdev, const char *res_name);
+
+#endif

linux-7.2.3/drivers/media/platform/ti/vpe/vip.h

@@ -0,0 +1,717 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * TI VIP capture driver
+ *
+ * Copyright (C) 2025 Texas Instruments Incorpated - http://www.ti.com/
+ * David Griego, <dagriego@biglakesoftware.com>
+ * Dale Farnsworth, <dale@farnsworth.org>
+ * Yemike Abhilash Chandra, <y-abhilashchandra@ti.com>
+ */
+
+#ifndef __TI_VIP_H
+#define __TI_VIP_H
+
+#include <linux/videodev2.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-ioctl.h>
+#include <media/videobuf2-core.h>
+#include <media/videobuf2-dma-contig.h>
+#include <media/videobuf2-memops.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-async.h>
+
+#include "vpdma.h"
+#include "vpdma_priv.h"
+#include "sc.h"
+#include "csc.h"
+
+#define VIP_INSTANCE1	1
+#define VIP_INSTANCE2	2
+#define VIP_INSTANCE3	3
+
+#define VIP_SLICE1	0
+#define VIP_SLICE2	1
+#define VIP_NUM_SLICES	2
+
+/*
+ * Additional client identifiers used for VPDMA configuration descriptors
+ */
+#define VIP_SLICE1_CFD_SC_CLIENT	7
+#define VIP_SLICE2_CFD_SC_CLIENT	8
+
+#define VIP_PORTA	0
+#define VIP_PORTB	1
+#define VIP_NUM_PORTS	2
+
+#define VIP_MAX_PLANES	2
+#define	VIP_LUMA	0
+#define VIP_CHROMA	1
+
+#define VIP_CAP_STREAMS_PER_PORT	16
+#define VIP_VBI_STREAMS_PER_PORT	16
+
+#define VIP_MAX_SUBDEV			5
+
+#define VPDMA_FIRMWARE	"vpdma-1b8.bin"
+
+/*
+ * This value needs to be at least as large as the number of entry in
+ * vip_formats[].
+ * When vip_formats[] is modified make sure to adjust this value also.
+ */
+#define VIP_MAX_ACTIVE_FMT		16
+/*
+ * Colorspace conversion unit can be in one of 3 modes:
+ * NA  - Not Available on this port
+ * Y2R - Needed for YUV to RGB on this port
+ * R2Y - Needed for RGB to YUV on this port
+ */
+enum vip_csc_state {
+	VIP_CSC_NA = 0,
+	VIP_CSC_Y2R,
+	VIP_CSC_R2Y,
+};
+
+/* buffer for one video frame */
+struct vip_buffer {
+	/* common v4l buffer stuff */
+	struct vb2_v4l2_buffer	vb;
+	struct list_head	list;
+	bool			drop;
+};
+
+/*
+ * struct vip_fmt - VIP media bus format information
+ * @fourcc: V4L2 pixel format FCC identifier
+ * @code: V4L2 media bus format code
+ * @colorspace: V4L2 colorspace identifier
+ * @coplanar: 1 if unpacked Luma and Chroma, 0 otherwise (packed/interleaved)
+ * @vpdma_fmt: VPDMA data format per plane.
+ * @finfo: Cache v4l2_format_info for associated fourcc
+ */
+struct vip_fmt {
+	u32	fourcc;
+	u32	code;
+	u32	colorspace;
+	u8	coplanar;
+	const struct vpdma_data_format *vpdma_fmt[VIP_MAX_PLANES];
+	const struct v4l2_format_info *finfo;
+};
+
+/*
+ * The vip_parser_data structures contains the memory mapped
+ * info to access the parser registers.
+ */
+struct vip_parser_data {
+	void __iomem		*base;
+
+	struct platform_device *pdev;
+};
+
+/*
+ * The vip_shared structure contains data that is shared by both
+ * the VIP1 and VIP2 slices.
+ */
+struct vip_shared {
+	struct list_head	list;
+	void __iomem		*base;
+	struct vpdma_data	vpdma_data;
+	struct vpdma_data	*vpdma;
+	struct v4l2_device	v4l2_dev;
+	struct vip_dev		*devs[VIP_NUM_SLICES];
+	struct v4l2_ctrl_handler ctrl_handler;
+};
+
+struct vip_ctrl_module {
+	struct regmap	*syscon_pol;
+	u32		syscon_offset;
+	u32		syscon_bit_field[4];
+};
+
+/*
+ * There are two vip_dev structure, one for each vip slice: VIP1 & VIP2.
+ */
+struct vip_dev {
+	struct v4l2_device	v4l2_dev;
+	struct platform_device	*pdev;
+	struct vip_shared	*shared;
+	struct vip_ctrl_module	*syscon;
+	int			instance_id;
+	int			slice_id;
+	int			num_ports;	/* count of open ports */
+	struct mutex		mutex;
+	/* protects access to stream buffer queues */
+	spinlock_t		slock;
+
+	int			irq;
+	void __iomem		*base;
+
+	struct vip_port		*ports[VIP_NUM_PORTS];
+
+	char			name[16];
+	/* parser data handle */
+	struct vip_parser_data	*parser;
+	/* scaler data handle */
+	struct sc_data		*sc;
+	/* scaler port assignation */
+	int			sc_assigned;
+	/* csc data handle */
+	struct csc_data		*csc;
+	/* csc port assignation */
+	int			csc_assigned;
+};
+
+/*
+ * There are two vip_port structures for each vip_dev, one for port A
+ * and one for port B.
+ */
+struct vip_port {
+	struct vip_dev		*dev;
+	int			port_id;
+
+	unsigned int		flags;
+	struct v4l2_rect	c_rect;		/* crop rectangle */
+	struct v4l2_mbus_framefmt mbus_framefmt;
+	struct v4l2_mbus_framefmt try_mbus_framefmt;
+
+	char			name[16];
+	struct vip_fmt		*fmt;		/* current format info */
+	/* Number of channels/streams configured */
+	int			num_streams_configured;
+	int			num_streams;	/* count of open streams */
+	struct vip_stream	*cap_streams[VIP_CAP_STREAMS_PER_PORT];
+
+	struct v4l2_async_notifier notifier;
+	struct v4l2_subdev	*subdev;
+	struct v4l2_fwnode_endpoint endpoint;
+	struct vip_fmt		*active_fmt[VIP_MAX_ACTIVE_FMT];
+	int			num_active_fmt;
+	/* have new shadow reg values */
+	bool			load_mmrs;
+	/* shadow reg addr/data block */
+	struct vpdma_buf	mmr_adb;
+	/* h coeff buffer */
+	struct vpdma_buf	sc_coeff_h;
+	/* v coeff buffer */
+	struct vpdma_buf	sc_coeff_v;
+	/* Show if scaler resource is available on this port */
+	bool			scaler;
+	/* Show the csc resource state on this port */
+	enum vip_csc_state	csc;
+};
+
+/*
+ * When handling multiplexed video, there can be multiple streams for each
+ * port.  The vip_stream structure holds per-stream data.
+ */
+struct vip_stream {
+	struct video_device	*vfd;
+	struct vip_port		*port;
+	int			stream_id;
+	int			list_num;
+	int			vfl_type;
+	char			name[16];
+	struct work_struct	recovery_work;
+	int			num_recovery;
+	enum v4l2_field		field;		/* current field */
+	unsigned int		sequence;	/* current frame/field seq */
+	enum v4l2_field		sup_field;	/* supported field value */
+	unsigned int		width;		/* frame width */
+	unsigned int		height;		/* frame height */
+	unsigned int		bytesperline;	/* bytes per line in memory */
+	unsigned int		sizeimage;	/* image size in memory */
+	struct list_head	vidq;		/* incoming vip_bufs queue */
+	struct list_head	dropq;		/* drop vip_bufs queue */
+	struct list_head	post_bufs;	/* vip_bufs to be DMAed */
+	/* Maintain a list of used channels - Needed for VPDMA cleanup */
+	int			vpdma_channels[VPDMA_MAX_CHANNELS];
+	int			vpdma_channels_to_abort[VPDMA_MAX_CHANNELS];
+	struct vpdma_desc_list	desc_list;	/* DMA descriptor list */
+	struct vpdma_dtd	*write_desc;
+	/* next unused desc_list addr */
+	void			*desc_next;
+	struct vb2_queue	vb_vidq;
+};
+
+/*
+ * VIP Enumerations
+ */
+enum data_path_select {
+	ALL_FIELDS_DATA_SELECT = 0,
+	VIP_CSC_SRC_DATA_SELECT,
+	VIP_SC_SRC_DATA_SELECT,
+	VIP_RGB_SRC_DATA_SELECT,
+	VIP_RGB_OUT_LO_DATA_SELECT,
+	VIP_RGB_OUT_HI_DATA_SELECT,
+	VIP_CHR_DS_1_SRC_DATA_SELECT,
+	VIP_CHR_DS_2_SRC_DATA_SELECT,
+	VIP_MULTI_CHANNEL_DATA_SELECT,
+	VIP_CHR_DS_1_DATA_BYPASS,
+	VIP_CHR_DS_2_DATA_BYPASS,
+};
+
+enum data_interface_modes {
+	SINGLE_24B_INTERFACE = 0,
+	SINGLE_16B_INTERFACE = 1,
+	DUAL_8B_INTERFACE = 2,
+};
+
+enum sync_types {
+	EMBEDDED_SYNC_SINGLE_YUV422 = 0,
+	EMBEDDED_SYNC_2X_MULTIPLEXED_YUV422 = 1,
+	EMBEDDED_SYNC_4X_MULTIPLEXED_YUV422 = 2,
+	EMBEDDED_SYNC_LINE_MULTIPLEXED_YUV422 = 3,
+	DISCRETE_SYNC_SINGLE_YUV422 = 4,
+	EMBEDDED_SYNC_SINGLE_RGB_OR_YUV444 = 5,
+	DISCRETE_SYNC_SINGLE_RGB_24B = 10,
+};
+
+#define VIP_NOT_ASSIGNED	-1
+
+/*
+ * Register offsets and field selectors
+ */
+#define VIP_PID_FUNC			0xf02
+
+#define VIP_PID				0x0000
+#define VIP_PID_MINOR_MASK              0x3f
+#define VIP_PID_MINOR_SHIFT             0
+#define VIP_PID_CUSTOM_MASK             0x03
+#define VIP_PID_CUSTOM_SHIFT            6
+#define VIP_PID_MAJOR_MASK              0x07
+#define VIP_PID_MAJOR_SHIFT             8
+#define VIP_PID_RTL_MASK                0x1f
+#define VIP_PID_RTL_SHIFT               11
+#define VIP_PID_FUNC_MASK               0xfff
+#define VIP_PID_FUNC_SHIFT              16
+#define VIP_PID_SCHEME_MASK             0x03
+#define VIP_PID_SCHEME_SHIFT            30
+
+#define VIP_SYSCONFIG			0x0010
+#define VIP_SYSCONFIG_IDLE_MASK         0x03
+#define VIP_SYSCONFIG_IDLE_SHIFT        2
+#define VIP_SYSCONFIG_STANDBY_MASK      0x03
+#define VIP_SYSCONFIG_STANDBY_SHIFT     4
+#define VIP_FORCE_IDLE_MODE             0
+#define VIP_NO_IDLE_MODE                1
+#define VIP_SMART_IDLE_MODE             2
+#define VIP_SMART_IDLE_WAKEUP_MODE      3
+#define VIP_FORCE_STANDBY_MODE          0
+#define VIP_NO_STANDBY_MODE             1
+#define VIP_SMART_STANDBY_MODE          2
+#define VIP_SMART_STANDBY_WAKEUP_MODE   3
+
+#define VIP_INTC_INTX_OFFSET		0x0020
+
+#define VIP_INT0_STATUS0_RAW_SET	0x0020
+#define VIP_INT0_STATUS0_RAW		VIP_INT0_STATUS0_RAW_SET
+#define VIP_INT0_STATUS0_CLR		0x0028
+#define VIP_INT0_STATUS0		VIP_INT0_STATUS0_CLR
+#define VIP_INT0_ENABLE0_SET		0x0030
+#define VIP_INT0_ENABLE0		VIP_INT0_ENABLE0_SET
+#define VIP_INT0_ENABLE0_CLR		0x0038
+#define VIP_INT0_LIST0_COMPLETE         BIT(0)
+#define VIP_INT0_LIST0_NOTIFY           BIT(1)
+#define VIP_INT0_LIST1_COMPLETE         BIT(2)
+#define VIP_INT0_LIST1_NOTIFY           BIT(3)
+#define VIP_INT0_LIST2_COMPLETE         BIT(4)
+#define VIP_INT0_LIST2_NOTIFY           BIT(5)
+#define VIP_INT0_LIST3_COMPLETE         BIT(6)
+#define VIP_INT0_LIST3_NOTIFY           BIT(7)
+#define VIP_INT0_LIST4_COMPLETE         BIT(8)
+#define VIP_INT0_LIST4_NOTIFY           BIT(9)
+#define VIP_INT0_LIST5_COMPLETE         BIT(10)
+#define VIP_INT0_LIST5_NOTIFY           BIT(11)
+#define VIP_INT0_LIST6_COMPLETE         BIT(12)
+#define VIP_INT0_LIST6_NOTIFY           BIT(13)
+#define VIP_INT0_LIST7_COMPLETE         BIT(14)
+#define VIP_INT0_LIST7_NOTIFY           BIT(15)
+#define VIP_INT0_DESCRIPTOR             BIT(16)
+#define VIP_VIP1_PARSER_INT		BIT(20)
+#define VIP_VIP2_PARSER_INT		BIT(21)
+
+#define VIP_INT0_STATUS1_RAW_SET        0x0024
+#define VIP_INT0_STATUS1_RAW            VIP_INT0_STATUS0_RAW_SET
+#define VIP_INT0_STATUS1_CLR            0x002c
+#define VIP_INT0_STATUS1                VIP_INT0_STATUS0_CLR
+#define VIP_INT0_ENABLE1_SET            0x0034
+#define VIP_INT0_ENABLE1                VIP_INT0_ENABLE0_SET
+#define VIP_INT0_ENABLE1_CLR            0x003c
+#define VIP_INT0_ENABLE1_STAT		0x004c
+#define VIP_INT0_CHANNEL_GROUP0		BIT(0)
+#define VIP_INT0_CHANNEL_GROUP1		BIT(1)
+#define VIP_INT0_CHANNEL_GROUP2		BIT(2)
+#define VIP_INT0_CHANNEL_GROUP3		BIT(3)
+#define VIP_INT0_CHANNEL_GROUP4		BIT(4)
+#define VIP_INT0_CHANNEL_GROUP5		BIT(5)
+#define VIP_INT0_CLIENT			BIT(7)
+#define VIP_VIP1_DS1_UV_ERROR_INT	BIT(22)
+#define VIP_VIP1_DS2_UV_ERROR_INT	BIT(23)
+#define VIP_VIP2_DS1_UV_ERROR_INT	BIT(24)
+#define VIP_VIP2_DS2_UV_ERROR_INT	BIT(25)
+
+#define VIP_INTC_E0I			0x00a0
+
+#define VIP_CLK_ENABLE			0x0100
+#define VIP_VPDMA_CLK_ENABLE		BIT(0)
+#define VIP_VIP1_DATA_PATH_CLK_ENABLE	BIT(16)
+#define VIP_VIP2_DATA_PATH_CLK_ENABLE	BIT(17)
+
+#define VIP_CLK_RESET			0x0104
+#define VIP_VPDMA_RESET			BIT(0)
+#define VIP_VPDMA_CLK_RESET_MASK	0x1
+#define VIP_VPDMA_CLK_RESET_SHIFT	0
+#define VIP_DATA_PATH_CLK_RESET_MASK	0x1
+#define VIP_VIP1_DATA_PATH_RESET_SHIFT	16
+#define VIP_VIP2_DATA_PATH_RESET_SHIFT	17
+#define VIP_VIP1_DATA_PATH_RESET	BIT(16)
+#define VIP_VIP2_DATA_PATH_RESET	BIT(17)
+#define VIP_VIP1_PARSER_RESET		BIT(18)
+#define VIP_VIP2_PARSER_RESET		BIT(19)
+#define VIP_VIP1_CSC_RESET		BIT(20)
+#define VIP_VIP2_CSC_RESET		BIT(21)
+#define VIP_VIP1_SC_RESET		BIT(22)
+#define VIP_VIP2_SC_RESET		BIT(23)
+#define VIP_VIP1_DS1_RESET		BIT(25)
+#define VIP_VIP2_DS1_RESET		BIT(26)
+#define VIP_VIP1_DS2_RESET		BIT(27)
+#define VIP_VIP2_DS2_RESET		BIT(28)
+#define VIP_MAIN_RESET			BIT(31)
+
+#define VIP_VIP1_DATA_PATH_SELECT	0x010c
+#define VIP_VIP2_DATA_PATH_SELECT	0x0110
+#define VIP_CSC_SRC_SELECT_MASK		0x07
+#define VIP_CSC_SRC_SELECT_SHFT		0
+#define VIP_SC_SRC_SELECT_MASK		0x07
+#define VIP_SC_SRC_SELECT_SHFT		3
+#define VIP_RGB_SRC_SELECT		BIT(6)
+#define VIP_RGB_OUT_LO_SRC_SELECT	BIT(7)
+#define VIP_RGB_OUT_HI_SRC_SELECT	BIT(8)
+#define VIP_DS1_SRC_SELECT_MASK		0x07
+#define VIP_DS1_SRC_SELECT_SHFT		9
+#define VIP_DS2_SRC_SELECT_MASK		0x07
+#define VIP_DS2_SRC_SELECT_SHFT		12
+#define VIP_MULTI_CHANNEL_SELECT	BIT(15)
+#define VIP_DS1_BYPASS			BIT(16)
+#define VIP_DS2_BYPASS			BIT(17)
+#define VIP_TESTPORT_B_SELECT		BIT(26)
+#define VIP_TESTPORT_A_SELECT		BIT(27)
+#define VIP_DATAPATH_SELECT_MASK	0x0f
+#define VIP_DATAPATH_SELECT_SHFT	28
+
+#define VIP_PARSER_MAIN_CFG		0x0000
+#define VIP_DATA_INTERFACE_MODE_MASK	0x03
+#define VIP_DATA_INTERFACE_MODE_SHFT	0
+#define VIP_CLIP_BLANK			BIT(4)
+#define VIP_CLIP_ACTIVE			BIT(5)
+
+#define VIP_SLICE0_PARSER		0x5500
+#define VIP_SLICE1_PARSER		0x5a00
+#define VIP_PARSER_PORTA_0		0x0004
+#define VIP_PARSER_PORTB_0		0x000c
+#define VIP_SYNC_TYPE_MASK		0x0f
+#define VIP_SYNC_TYPE_SHFT		0
+#define VIP_CTRL_CHANNEL_SEL_MASK	0x03
+#define VIP_CTRL_CHANNEL_SEL_SHFT	4
+#define VIP_ASYNC_FIFO_WR		BIT(6)
+#define VIP_ASYNC_FIFO_RD		BIT(7)
+#define VIP_PORT_ENABLE			BIT(8)
+#define VIP_FID_POLARITY		BIT(9)
+#define VIP_PIXCLK_EDGE_POLARITY	BIT(10)
+#define VIP_HSYNC_POLARITY		BIT(11)
+#define VIP_VSYNC_POLARITY		BIT(12)
+#define VIP_ACTVID_POLARITY		BIT(13)
+#define VIP_FID_DETECT_MODE		BIT(14)
+#define VIP_USE_ACTVID_HSYNC_ONLY	BIT(15)
+#define VIP_FID_SKEW_PRECOUNT_MASK	0x3f
+#define VIP_FID_SKEW_PRECOUNT_SHFT	16
+#define VIP_DISCRETE_BASIC_MODE		BIT(22)
+#define VIP_SW_RESET			BIT(23)
+#define VIP_FID_SKEW_POSTCOUNT_MASK	0x3f
+#define VIP_FID_SKEW_POSTCOUNT_SHFT	24
+#define VIP_ANALYZER_2X4X_SRCNUM_POS	BIT(30)
+#define VIP_ANALYZER_FVH_ERR_COR_EN	BIT(31)
+
+#define VIP_PARSER_PORTA_1		0x0008
+#define VIP_PARSER_PORTB_1		0x0010
+#define VIP_SRC0_NUMLINES_MASK		0x0fff
+#define VIP_SRC0_NUMLINES_SHFT		0
+#define VIP_ANC_CHAN_SEL_8B_MASK	0x03
+#define VIP_ANC_CHAN_SEL_8B_SHFT	13
+#define VIP_SRC0_NUMPIX_MASK		0x0fff
+#define VIP_SRC0_NUMPIX_SHFT		16
+#define VIP_REPACK_SEL_MASK		0x07
+#define VIP_REPACK_SEL_SHFT		28
+
+#define VIP_PARSER_FIQ_MASK		0x0014
+#define VIP_PARSER_FIQ_CLR		0x0018
+#define VIP_PARSER_FIQ_STATUS		0x001c
+#define VIP_PORTA_VDET			BIT(0)
+#define VIP_PORTB_VDET			BIT(1)
+#define VIP_PORTA_ASYNC_FIFO_OF		BIT(2)
+#define VIP_PORTB_ASYNC_FIFO_OF		BIT(3)
+#define VIP_PORTA_OUTPUT_FIFO_YUV	BIT(4)
+#define VIP_PORTA_OUTPUT_FIFO_ANC	BIT(6)
+#define VIP_PORTB_OUTPUT_FIFO_YUV	BIT(7)
+#define VIP_PORTB_OUTPUT_FIFO_ANC	BIT(9)
+#define VIP_PORTA_CONN			BIT(10)
+#define VIP_PORTA_DISCONN		BIT(11)
+#define VIP_PORTB_CONN			BIT(12)
+#define VIP_PORTB_DISCONN		BIT(13)
+#define VIP_PORTA_SRC0_SIZE		BIT(14)
+#define VIP_PORTB_SRC0_SIZE		BIT(15)
+#define VIP_PORTA_YUV_PROTO_VIOLATION	BIT(16)
+#define VIP_PORTA_ANC_PROTO_VIOLATION	BIT(17)
+#define VIP_PORTB_YUV_PROTO_VIOLATION	BIT(18)
+#define VIP_PORTB_ANC_PROTO_VIOLATION	BIT(19)
+#define VIP_PORTA_CFG_DISABLE_COMPLETE	BIT(20)
+#define VIP_PORTB_CFG_DISABLE_COMPLETE	BIT(21)
+
+#define VIP_PARSER_PORTA_SOURCE_FID	0x0020
+#define VIP_PARSER_PORTA_ENCODER_FID	0x0024
+#define VIP_PARSER_PORTB_SOURCE_FID	0x0028
+#define VIP_PARSER_PORTB_ENCODER_FID	0x002c
+
+#define VIP_PARSER_PORTA_SRC0_SIZE	0x0030
+#define VIP_PARSER_PORTB_SRC0_SIZE	0x0070
+#define VIP_SOURCE_HEIGHT_MASK		0x0fff
+#define VIP_SOURCE_HEIGHT_SHFT		0
+#define VIP_SOURCE_WIDTH_MASK		0x0fff
+#define VIP_SOURCE_WIDTH_SHFT		16
+
+#define VIP_PARSER_PORTA_VDET_VEC	0x00b0
+#define VIP_PARSER_PORTB_VDET_VEC	0x00b4
+
+#define VIP_PARSER_PORTA_EXTRA2		0x00b8
+#define VIP_PARSER_PORTB_EXTRA2		0x00c8
+#define VIP_ANC_SKIP_NUMPIX_MASK	0x0fff
+#define VIP_ANC_SKIP_NUMPIX_SHFT	0
+#define VIP_ANC_BYPASS			BIT(15)
+#define VIP_ANC_USE_NUMPIX_MASK		0x0fff
+#define VIP_ANC_USE_NUMPIX_SHFT		16
+#define VIP_ANC_TARGET_SRCNUM_MASK	0x0f
+#define VIP_ANC_TARGET_SRCNUM_SHFT	28
+
+#define VIP_PARSER_PORTA_EXTRA3		0x00bc
+#define VIP_PARSER_PORTB_EXTRA3		0x00cc
+#define VIP_ANC_SKIP_NUMLINES_MASK	0x0fff
+#define VIP_ANC_SKIP_NUMLINES_SHFT	0
+#define VIP_ANC_USE_NUMLINES_MASK	0x0fff
+#define VIP_ANC_USE_NUMLINES_SHFT	16
+
+#define VIP_PARSER_PORTA_EXTRA4		0x00c0
+#define VIP_PARSER_PORTB_EXTRA4		0x00d0
+#define VIP_ACT_SKIP_NUMPIX_MASK	0x0fff
+#define VIP_ACT_SKIP_NUMPIX_SHFT	0
+#define VIP_ACT_BYPASS			BIT(15)
+#define VIP_ACT_USE_NUMPIX_MASK		0x0fff
+#define VIP_ACT_USE_NUMPIX_SHFT		16
+#define VIP_ACT_TARGET_SRCNUM_MASK	0x0f
+#define VIP_ACT_TARGET_SRCNUM_SHFT	28
+
+#define VIP_PARSER_PORTA_EXTRA5		0x00c4
+#define VIP_PARSER_PORTB_EXTRA5		0x00d4
+#define VIP_ACT_SKIP_NUMLINES_MASK	0x0fff
+#define VIP_ACT_SKIP_NUMLINES_SHFT	0
+#define VIP_ACT_USE_NUMLINES_MASK	0x0fff
+#define VIP_ACT_USE_NUMLINES_SHFT	16
+
+#define VIP_PARSER_PORTA_EXTRA6		0x00d8
+#define VIP_PARSER_PORTB_EXTRA6		0x00dc
+#define VIP_ANC_SRCNUM_STOP_IMM_SHFT	0
+#define VIP_YUV_SRCNUM_STOP_IMM_SHFT	16
+
+#define VIP_SLICE0_CSC			0x5700
+#define VIP_SLICE1_CSC			0x5c00
+#define VIP_CSC_CSC00			0x0200
+#define VIP_CSC_A0_MASK			0x1fff
+#define VIP_CSC_A0_SHFT			0
+#define VIP_CSC_B0_MASK			0x1fff
+#define VIP_CSC_B0_SHFT			16
+
+#define VIP_CSC_CSC01			0x0204
+#define VIP_CSC_C0_MASK			0x1fff
+#define VIP_CSC_C0_SHFT			0
+#define VIP_CSC_A1_MASK			0x1fff
+#define VIP_CSC_A1_SHFT			16
+
+#define VIP_CSC_CSC02			0x0208
+#define VIP_CSC_B1_MASK			0x1fff
+#define VIP_CSC_B1_SHFT			0
+#define VIP_CSC_C1_MASK			0x1fff
+#define VIP_CSC_C1_SHFT			16
+
+#define VIP_CSC_CSC03			0x020c
+#define VIP_CSC_A2_MASK			0x1fff
+#define VIP_CSC_A2_SHFT			0
+#define VIP_CSC_B2_MASK			0x1fff
+#define VIP_CSC_B2_SHFT			16
+
+#define VIP_CSC_CSC04			0x0210
+#define VIP_CSC_C2_MASK			0x1fff
+#define VIP_CSC_C2_SHFT			0
+#define VIP_CSC_D0_MASK			0x0fff
+#define VIP_CSC_D0_SHFT			16
+
+#define VIP_CSC_CSC05			0x0214
+#define VIP_CSC_D1_MASK			0x0fff
+#define VIP_CSC_D1_SHFT			0
+#define VIP_CSC_D2_MASK			0x0fff
+#define VIP_CSC_D2_SHFT			16
+#define VIP_CSC_BYPASS			BIT(28)
+
+#define VIP_SLICE0_SC			0x5800
+#define VIP_SLICE1_SC			0x5d00
+#define VIP_SC_MP_SC0			0x0300
+#define VIP_INTERLACE_O			BIT(0)
+#define VIP_LINEAR			BIT(1)
+#define VIP_SC_BYPASS			BIT(2)
+#define VIP_INVT_FID			BIT(3)
+#define VIP_USE_RAV			BIT(4)
+#define VIP_ENABLE_EV			BIT(5)
+#define VIP_AUTH_HS			BIT(6)
+#define VIP_DCM_2X			BIT(7)
+#define VIP_DCM_4X			BIT(8)
+#define VIP_HP_BYPASS			BIT(9)
+#define VIP_INTERLACE_I			BIT(10)
+#define VIP_ENABLE_SIN2_VER_INTP	BIT(11)
+#define VIP_Y_PK_EN			BIT(14)
+#define VIP_TRIM			BIT(15)
+#define VIP_SELFGEN_FID			BIT(16)
+
+#define VIP_SC_MP_SC1			0x0304
+#define VIP_ROW_ACC_INC_MASK		0x07ffffff
+#define VIP_ROW_ACC_INC_SHFT		0
+
+#define VIP_SC_MP_SC2			0x0308
+#define VIP_ROW_ACC_OFFSET_MASK		0x0fffffff
+#define VIP_ROW_ACC_OFFSET_SHFT		0
+
+#define VIP_SC_MP_SC3			0x030c
+#define VIP_ROW_ACC_OFFSET_B_MASK	0x0fffffff
+#define VIP_ROW_ACC_OFFSET_B_SHFT	0
+
+#define VIP_SC_MP_SC4			0x0310
+#define VIP_TAR_H_MASK			0x07ff
+#define VIP_TAR_H_SHFT			0
+#define VIP_TAR_W_MASK			0x07ff
+#define VIP_TAR_W_SHFT			12
+#define VIP_LIN_ACC_INC_U_MASK		0x07
+#define VIP_LIN_ACC_INC_U_SHFT		24
+#define VIP_NLIN_ACC_INIT_U_MASK	0x07
+#define VIP_NLIN_ACC_INIT_U_SHFT	28
+
+#define VIP_SC_MP_SC5			0x0314
+#define VIP_SRC_H_MASK			0x03ff
+#define VIP_SRC_H_SHFT			0
+#define VIP_SRC_W_MASK			0x07ff
+#define VIP_SRC_W_SHFT			12
+#define VIP_NLIN_ACC_INC_U_MASK		0x07
+#define VIP_NLIN_ACC_INC_U_SHFT		24
+
+#define VIP_SC_MP_SC6			0x0318
+#define VIP_ROW_ACC_INIT_RAV_MASK	0x03ff
+#define VIP_ROW_ACC_INIT_RAV_SHFT	0
+#define VIP_ROW_ACC_INIT_RAV_B_MASK	0x03ff
+#define VIP_ROW_ACC_INIT_RAV_B_SHFT	10
+
+#define VIP_SC_MP_SC8			0x0320
+#define VIP_NLIN_LEFT_MASK		0x07ff
+#define VIP_NLIN_LEFT_SHFT		0
+#define VIP_NLIN_RIGHT_MASK		0x07ff
+#define VIP_NLIN_RIGHT_SHFT		12
+
+#define VIP_SC_MP_SC9			0x0324
+#define VIP_LIN_ACC_INC			VIP_SC_MP_SC9
+
+#define VIP_SC_MP_SC10			0x0328
+#define VIP_NLIN_ACC_INIT		VIP_SC_MP_SC10
+
+#define VIP_SC_MP_SC11			0x032c
+#define VIP_NLIN_ACC_INC		VIP_SC_MP_SC11
+
+#define VIP_SC_MP_SC12			0x0330
+#define VIP_COL_ACC_OFFSET_MASK		0x01ffffff
+#define VIP_COL_ACC_OFFSET_SHFT		0
+
+#define VIP_SC_MP_SC13			0x0334
+#define VIP_SC_FACTOR_RAV_MASK		0x03ff
+#define VIP_SC_FACTOR_RAV_SHFT		0
+#define VIP_CHROMA_INTP_THR_MASK	0x03ff
+#define VIP_CHROMA_INTP_THR_SHFT	12
+#define VIP_DELTA_CHROMA_THR_MASK	0x0f
+#define VIP_DELTA_CHROMA_THR_SHFT	24
+
+#define VIP_SC_MP_SC17			0x0344
+#define VIP_EV_THR_MASK			0x03ff
+#define VIP_EV_THR_SHFT			12
+#define VIP_DELTA_LUMA_THR_MASK		0x0f
+#define VIP_DELTA_LUMA_THR_SHFT		24
+#define VIP_DELTA_EV_THR_MASK		0x0f
+#define VIP_DELTA_EV_THR_SHFT		28
+
+#define VIP_SC_MP_SC18			0x0348
+#define VIP_HS_FACTOR_MASK		0x03ff
+#define VIP_HS_FACTOR_SHFT		0
+#define VIP_CONF_DEFAULT_MASK		0x01ff
+#define VIP_CONF_DEFAULT_SHFT		16
+
+#define VIP_SC_MP_SC19			0x034c
+#define VIP_HPF_COEFF0_MASK		0xff
+#define VIP_HPF_COEFF0_SHFT		0
+#define VIP_HPF_COEFF1_MASK		0xff
+#define VIP_HPF_COEFF1_SHFT		8
+#define VIP_HPF_COEFF2_MASK		0xff
+#define VIP_HPF_COEFF2_SHFT		16
+#define VIP_HPF_COEFF3_MASK		0xff
+#define VIP_HPF_COEFF3_SHFT		23
+
+#define VIP_SC_MP_SC20			0x0350
+#define VIP_HPF_COEFF4_MASK		0xff
+#define VIP_HPF_COEFF4_SHFT		0
+#define VIP_HPF_COEFF5_MASK		0xff
+#define VIP_HPF_COEFF5_SHFT		8
+#define VIP_HPF_NORM_SHFT_MASK		0x07
+#define VIP_HPF_NORM_SHFT_SHFT		16
+#define VIP_NL_LIMIT_MASK		0x1ff
+#define VIP_NL_LIMIT_SHFT		20
+
+#define VIP_SC_MP_SC21			0x0354
+#define VIP_NL_LO_THR_MASK		0x01ff
+#define VIP_NL_LO_THR_SHFT		0
+#define VIP_NL_LO_SLOPE_MASK		0xff
+#define VIP_NL_LO_SLOPE_SHFT		16
+
+#define VIP_SC_MP_SC22			0x0358
+#define VIP_NL_HI_THR_MASK		0x01ff
+#define VIP_NL_HI_THR_SHFT		0
+#define VIP_NL_HI_SLOPE_SH_MASK		0x07
+#define VIP_NL_HI_SLOPE_SH_SHFT		16
+
+#define VIP_SC_MP_SC23			0x035c
+#define VIP_GRADIENT_THR_MASK		0x07ff
+#define VIP_GRADIENT_THR_SHFT		0
+#define VIP_GRADIENT_THR_RANGE_MASK	0x0f
+#define VIP_GRADIENT_THR_RANGE_SHFT	12
+#define VIP_MIN_GY_THR_MASK		0xff
+#define VIP_MIN_GY_THR_SHFT		16
+#define VIP_MIN_GY_THR_RANGE_MASK	0x0f
+#define VIP_MIN_GY_THR_RANGE_SHFT	28
+
+#define VIP_SC_MP_SC24			0x0360
+#define VIP_ORG_H_MASK			0x07ff
+#define VIP_ORG_H_SHFT			0
+#define VIP_ORG_W_MASK			0x07ff
+#define VIP_ORG_W_SHFT			16
+
+#define VIP_SC_MP_SC25			0x0364
+#define VIP_OFF_H_MASK			0x07ff
+#define VIP_OFF_H_SHFT			0
+#define VIP_OFF_W_MASK			0x07ff
+#define VIP_OFF_W_SHFT			16
+
+#define VIP_VPDMA_BASE			0xd000
+
+#endif

linux-7.2.3/drivers/media/platform/ti/vpe/vpdma.h

@@ -0,0 +1,287 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2013 Texas Instruments Inc.
+ *
+ * David Griego, <dagriego@biglakesoftware.com>
+ * Dale Farnsworth, <dale@farnsworth.org>
+ * Archit Taneja, <archit@ti.com>
+ */
+
+#ifndef __TI_VPDMA_H_
+#define __TI_VPDMA_H_
+
+#define VPDMA_MAX_NUM_LIST		8
+/*
+ * A vpdma_buf tracks the size, DMA address and mapping status of each
+ * driver DMA area.
+ */
+struct vpdma_buf {
+	void			*addr;
+	dma_addr_t		dma_addr;
+	size_t			size;
+	bool			mapped;
+};
+
+struct vpdma_desc_list {
+	struct vpdma_buf buf;
+	void *next;
+	int type;
+};
+
+struct vpdma_data {
+	void __iomem		*base;
+
+	struct platform_device	*pdev;
+
+	spinlock_t		lock;
+	bool			hwlist_used[VPDMA_MAX_NUM_LIST];
+	void			*hwlist_priv[VPDMA_MAX_NUM_LIST];
+	/* callback to VPE driver when the firmware is loaded */
+	void (*cb)(struct platform_device *pdev);
+};
+
+enum vpdma_data_format_type {
+	VPDMA_DATA_FMT_TYPE_YUV,
+	VPDMA_DATA_FMT_TYPE_RGB,
+	VPDMA_DATA_FMT_TYPE_MISC,
+};
+
+struct vpdma_data_format {
+	enum vpdma_data_format_type type;
+	int data_type;
+	u8 depth;
+};
+
+#define VPDMA_DESC_ALIGN		16	/* 16-byte descriptor alignment */
+#define VPDMA_STRIDE_ALIGN		16	/*
+						 * line stride of source and dest
+						 * buffers should be 16 byte aligned
+						 */
+#define VPDMA_MAX_STRIDE		65520	/* Max line stride 16 byte aligned */
+#define VPDMA_DTD_DESC_SIZE		32	/* 8 words */
+#define VPDMA_CFD_CTD_DESC_SIZE		16	/* 4 words */
+
+#define VPDMA_LIST_TYPE_NORMAL		0
+#define VPDMA_LIST_TYPE_SELF_MODIFYING	1
+#define VPDMA_LIST_TYPE_DOORBELL	2
+
+enum vpdma_yuv_formats {
+	VPDMA_DATA_FMT_Y444 = 0,
+	VPDMA_DATA_FMT_Y422,
+	VPDMA_DATA_FMT_Y420,
+	VPDMA_DATA_FMT_C444,
+	VPDMA_DATA_FMT_C422,
+	VPDMA_DATA_FMT_C420,
+	VPDMA_DATA_FMT_CB420,
+	VPDMA_DATA_FMT_YCR422,
+	VPDMA_DATA_FMT_YC444,
+	VPDMA_DATA_FMT_CRY422,
+	VPDMA_DATA_FMT_CBY422,
+	VPDMA_DATA_FMT_YCB422,
+};
+
+enum vpdma_rgb_formats {
+	VPDMA_DATA_FMT_RGB565 = 0,
+	VPDMA_DATA_FMT_ARGB16_1555,
+	VPDMA_DATA_FMT_ARGB16,
+	VPDMA_DATA_FMT_RGBA16_5551,
+	VPDMA_DATA_FMT_RGBA16,
+	VPDMA_DATA_FMT_ARGB24,
+	VPDMA_DATA_FMT_RGB24,
+	VPDMA_DATA_FMT_ARGB32,
+	VPDMA_DATA_FMT_RGBA24,
+	VPDMA_DATA_FMT_RGBA32,
+	VPDMA_DATA_FMT_BGR565,
+	VPDMA_DATA_FMT_ABGR16_1555,
+	VPDMA_DATA_FMT_ABGR16,
+	VPDMA_DATA_FMT_BGRA16_5551,
+	VPDMA_DATA_FMT_BGRA16,
+	VPDMA_DATA_FMT_ABGR24,
+	VPDMA_DATA_FMT_BGR24,
+	VPDMA_DATA_FMT_ABGR32,
+	VPDMA_DATA_FMT_BGRA24,
+	VPDMA_DATA_FMT_BGRA32,
+};
+
+enum vpdma_raw_formats {
+	VPDMA_DATA_FMT_RAW8 = 0,
+	VPDMA_DATA_FMT_RAW16,
+};
+
+enum vpdma_misc_formats {
+	VPDMA_DATA_FMT_MV = 0,
+};
+
+extern const struct vpdma_data_format vpdma_yuv_fmts[];
+extern const struct vpdma_data_format vpdma_rgb_fmts[];
+extern const struct vpdma_data_format vpdma_raw_fmts[];
+extern const struct vpdma_data_format vpdma_misc_fmts[];
+
+enum vpdma_frame_start_event {
+	VPDMA_FSEVENT_HDMI_FID = 0,
+	VPDMA_FSEVENT_DVO2_FID,
+	VPDMA_FSEVENT_HDCOMP_FID,
+	VPDMA_FSEVENT_SD_FID,
+	VPDMA_FSEVENT_LM_FID0,
+	VPDMA_FSEVENT_LM_FID1,
+	VPDMA_FSEVENT_LM_FID2,
+	VPDMA_FSEVENT_CHANNEL_ACTIVE,
+};
+
+/* max width configurations */
+enum vpdma_max_width {
+	MAX_OUT_WIDTH_UNLIMITED = 0,
+	MAX_OUT_WIDTH_REG1,
+	MAX_OUT_WIDTH_REG2,
+	MAX_OUT_WIDTH_REG3,
+	MAX_OUT_WIDTH_352,
+	MAX_OUT_WIDTH_768,
+	MAX_OUT_WIDTH_1280,
+	MAX_OUT_WIDTH_1920,
+};
+
+/* max height configurations */
+enum vpdma_max_height {
+	MAX_OUT_HEIGHT_UNLIMITED = 0,
+	MAX_OUT_HEIGHT_REG1,
+	MAX_OUT_HEIGHT_REG2,
+	MAX_OUT_HEIGHT_REG3,
+	MAX_OUT_HEIGHT_288,
+	MAX_OUT_HEIGHT_576,
+	MAX_OUT_HEIGHT_720,
+	MAX_OUT_HEIGHT_1080,
+};
+
+/*
+ * VPDMA channel numbers
+ */
+enum vpdma_channel {
+	VPE_CHAN_LUMA1_IN,
+	VPE_CHAN_CHROMA1_IN,
+	VPE_CHAN_LUMA2_IN,
+	VPE_CHAN_CHROMA2_IN,
+	VPE_CHAN_LUMA3_IN,
+	VPE_CHAN_CHROMA3_IN,
+	VPE_CHAN_MV_IN,
+	VPE_CHAN_MV_OUT,
+	VPE_CHAN_LUMA_OUT,
+	VPE_CHAN_CHROMA_OUT,
+	VPE_CHAN_RGB_OUT,
+};
+
+#define VIP_CHAN_VIP2_OFFSET		70
+#define VIP_CHAN_MULT_PORTB_OFFSET	16
+#define VIP_CHAN_YUV_PORTB_OFFSET	2
+#define VIP_CHAN_RGB_PORTB_OFFSET	1
+
+#define VPDMA_MAX_CHANNELS		256
+
+/* flags for VPDMA data descriptors */
+#define VPDMA_DATA_ODD_LINE_SKIP	(1 << 0)
+#define VPDMA_DATA_EVEN_LINE_SKIP	(1 << 1)
+#define VPDMA_DATA_FRAME_1D		(1 << 2)
+#define VPDMA_DATA_MODE_TILED		(1 << 3)
+
+/*
+ * client identifiers used for configuration descriptors
+ */
+#define CFD_MMR_CLIENT		0
+#define CFD_SC_CLIENT		4
+
+/* Address data block header format */
+struct vpdma_adb_hdr {
+	u32			offset;
+	u32			nwords;
+	u32			reserved0;
+	u32			reserved1;
+};
+
+/* helpers for creating ADB headers for config descriptors MMRs as client */
+#define ADB_ADDR(dma_buf, str, fld)	((dma_buf)->addr + offsetof(str, fld))
+#define MMR_ADB_ADDR(buf, str, fld)	ADB_ADDR(&(buf), struct str, fld)
+
+#define VPDMA_SET_MMR_ADB_HDR(buf, str, hdr, regs, offset_a)	\
+	do {							\
+		struct vpdma_adb_hdr *h;			\
+		struct str *adb = NULL;				\
+		h = MMR_ADB_ADDR(buf, str, hdr);		\
+		h->offset = (offset_a);				\
+		h->nwords = sizeof(adb->regs) >> 2;		\
+	} while (0)
+
+/* vpdma descriptor buffer allocation and management */
+int vpdma_alloc_desc_buf(struct vpdma_buf *buf, size_t size);
+void vpdma_free_desc_buf(struct vpdma_buf *buf);
+int vpdma_map_desc_buf(struct vpdma_data *vpdma, struct vpdma_buf *buf);
+void vpdma_unmap_desc_buf(struct vpdma_data *vpdma, struct vpdma_buf *buf);
+
+/* vpdma descriptor list funcs */
+int vpdma_create_desc_list(struct vpdma_desc_list *list, size_t size, int type);
+void vpdma_reset_desc_list(struct vpdma_desc_list *list);
+void vpdma_free_desc_list(struct vpdma_desc_list *list);
+int vpdma_submit_descs(struct vpdma_data *vpdma, struct vpdma_desc_list *list,
+		       int list_num);
+bool vpdma_list_busy(struct vpdma_data *vpdma, int list_num);
+void vpdma_update_dma_addr(struct vpdma_data *vpdma,
+			   struct vpdma_desc_list *list, dma_addr_t dma_addr,
+			   void *write_dtd, int drop, int idx);
+
+/* VPDMA hardware list funcs */
+int vpdma_hwlist_alloc(struct vpdma_data *vpdma, void *priv);
+void *vpdma_hwlist_get_priv(struct vpdma_data *vpdma, int list_num);
+void *vpdma_hwlist_release(struct vpdma_data *vpdma, int list_num);
+
+/* helpers for creating vpdma descriptors */
+void vpdma_add_cfd_block(struct vpdma_desc_list *list, int client,
+		struct vpdma_buf *blk, u32 dest_offset);
+void vpdma_add_cfd_adb(struct vpdma_desc_list *list, int client,
+		struct vpdma_buf *adb);
+void vpdma_add_sync_on_channel_ctd(struct vpdma_desc_list *list,
+		enum vpdma_channel chan);
+void vpdma_add_abort_channel_ctd(struct vpdma_desc_list *list,
+		int chan_num);
+void vpdma_add_out_dtd(struct vpdma_desc_list *list, int width,
+		int stride, const struct v4l2_rect *c_rect,
+		const struct vpdma_data_format *fmt, dma_addr_t dma_addr,
+		int max_w, int max_h, enum vpdma_channel chan, u32 flags);
+void vpdma_rawchan_add_out_dtd(struct vpdma_desc_list *list, int width,
+		int stride, const struct v4l2_rect *c_rect,
+		const struct vpdma_data_format *fmt, dma_addr_t dma_addr,
+		int max_w, int max_h, int raw_vpdma_chan, u32 flags);
+
+void vpdma_add_in_dtd(struct vpdma_desc_list *list, int width,
+		int stride, const struct v4l2_rect *c_rect,
+		const struct vpdma_data_format *fmt, dma_addr_t dma_addr,
+		enum vpdma_channel chan, int field, u32 flags, int frame_width,
+		int frame_height, int start_h, int start_v);
+int vpdma_list_cleanup(struct vpdma_data *vpdma, int list_num,
+		int *channels, int size);
+
+/* vpdma list interrupt management */
+void vpdma_enable_list_complete_irq(struct vpdma_data *vpdma, int irq_num,
+		int list_num, bool enable);
+void vpdma_clear_list_stat(struct vpdma_data *vpdma, int irq_num,
+			   int list_num);
+unsigned int vpdma_get_list_stat(struct vpdma_data *vpdma, int irq_num);
+unsigned int vpdma_get_list_mask(struct vpdma_data *vpdma, int irq_num);
+
+/* vpdma client configuration */
+void vpdma_set_line_mode(struct vpdma_data *vpdma, int line_mode,
+		enum vpdma_channel chan);
+void vpdma_set_frame_start_event(struct vpdma_data *vpdma,
+		enum vpdma_frame_start_event fs_event, enum vpdma_channel chan);
+void vpdma_set_max_size(struct vpdma_data *vpdma, int reg_addr,
+			u32 width, u32 height);
+
+void vpdma_set_bg_color(struct vpdma_data *vpdma,
+			struct vpdma_data_format *fmt, u32 color);
+void vpdma_dump_regs(struct vpdma_data *vpdma);
+
+/* initialize vpdma, passed with VPE's platform device pointer */
+int vpdma_create(struct platform_device *pdev, struct vpdma_data *vpdma,
+		void (*cb)(struct platform_device *pdev));
+
+/* load vpdma firmware*/
+int vpdma_load_firmware(struct vpdma_data *vpdma);
+
+#endif

linux-7.2.3/drivers/media/platform/ti/vpe/vpdma_priv.h

@@ -0,0 +1,639 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2013 Texas Instruments Inc.
+ *
+ * David Griego, <dagriego@biglakesoftware.com>
+ * Dale Farnsworth, <dale@farnsworth.org>
+ * Archit Taneja, <archit@ti.com>
+ */
+
+#ifndef _TI_VPDMA_PRIV_H_
+#define _TI_VPDMA_PRIV_H_
+
+/*
+ * VPDMA Register offsets
+ */
+
+/* Top level */
+#define VPDMA_PID		0x00
+#define VPDMA_LIST_ADDR		0x04
+#define VPDMA_LIST_ATTR		0x08
+#define VPDMA_LIST_STAT_SYNC	0x0c
+#define VPDMA_BG_RGB		0x18
+#define VPDMA_BG_YUV		0x1c
+#define VPDMA_SETUP		0x30
+#define VPDMA_MAX_SIZE1		0x34
+#define VPDMA_MAX_SIZE2		0x38
+#define VPDMA_MAX_SIZE3		0x3c
+#define VPDMA_MAX_SIZE_WIDTH_MASK	0xffff
+#define VPDMA_MAX_SIZE_WIDTH_SHFT	16
+#define VPDMA_MAX_SIZE_HEIGHT_MASK	0xffff
+#define VPDMA_MAX_SIZE_HEIGHT_SHFT	0
+
+/* Interrupts */
+#define VPDMA_INT_CHAN_STAT(grp)	(0x40 + grp * 8)
+#define VPDMA_INT_CHAN_MASK(grp)	(VPDMA_INT_CHAN_STAT(grp) + 4)
+#define VPDMA_INT_CLIENT0_STAT		0x78
+#define VPDMA_INT_CLIENT0_MASK		0x7c
+#define VPDMA_INT_CLIENT1_STAT		0x80
+#define VPDMA_INT_CLIENT1_MASK		0x84
+#define VPDMA_INT_LIST0_STAT		0x88
+#define VPDMA_INT_LIST0_MASK		0x8c
+
+#define VPDMA_INTX_OFFSET		0x50
+
+#define VPDMA_PERFMON(i)		(0x200 + i * 4)
+
+/* VIP/VPE client registers */
+#define VPDMA_DEI_CHROMA1_CSTAT		0x0300
+#define VPDMA_DEI_LUMA1_CSTAT		0x0304
+#define VPDMA_DEI_LUMA2_CSTAT		0x0308
+#define VPDMA_DEI_CHROMA2_CSTAT		0x030c
+#define VPDMA_DEI_LUMA3_CSTAT		0x0310
+#define VPDMA_DEI_CHROMA3_CSTAT		0x0314
+#define VPDMA_DEI_MV_IN_CSTAT		0x0330
+#define VPDMA_DEI_MV_OUT_CSTAT		0x033c
+#define VPDMA_VIP_LO_Y_CSTAT		0x0388
+#define VPDMA_VIP_LO_UV_CSTAT		0x038c
+#define VPDMA_VIP_UP_Y_CSTAT		0x0390
+#define VPDMA_VIP_UP_UV_CSTAT		0x0394
+#define VPDMA_VPI_CTL_CSTAT		0x03d0
+
+/* Reg field info for VPDMA_CLIENT_CSTAT registers */
+#define VPDMA_CSTAT_LINE_MODE_MASK	0x03
+#define VPDMA_CSTAT_LINE_MODE_SHIFT	8
+#define VPDMA_CSTAT_FRAME_START_MASK	0xf
+#define VPDMA_CSTAT_FRAME_START_SHIFT	10
+
+#define VPDMA_LIST_NUM_MASK		0x07
+#define VPDMA_LIST_NUM_SHFT		24
+#define VPDMA_LIST_STOP_SHFT		20
+#define VPDMA_LIST_RDY_MASK		0x01
+#define VPDMA_LIST_RDY_SHFT		19
+#define VPDMA_LIST_TYPE_MASK		0x03
+#define VPDMA_LIST_TYPE_SHFT		16
+#define VPDMA_LIST_SIZE_MASK		0xffff
+
+/*
+ * The YUV data type definition below are taken from
+ * both the TRM and i839 Errata information.
+ * Use the correct data type considering byte
+ * reordering of components.
+ *
+ * Also since the single use of "C" in the 422 case
+ * to mean "Cr" (i.e. V component). It was decided
+ * to explicitly label them CR to remove any confusion.
+ * Bear in mind that the type label refer to the memory
+ * packed order (LSB - MSB).
+ */
+#define DATA_TYPE_Y444				0x0
+#define DATA_TYPE_Y422				0x1
+#define DATA_TYPE_Y420				0x2
+#define DATA_TYPE_C444				0x4
+#define DATA_TYPE_C422				0x5
+#define DATA_TYPE_C420				0x6
+#define DATA_TYPE_CB420				0x16
+#define DATA_TYPE_YC444				0x8
+#define DATA_TYPE_YCB422			0x7
+#define DATA_TYPE_YCR422			0x17
+#define DATA_TYPE_CBY422			0x27
+#define DATA_TYPE_CRY422			0x37
+
+/*
+ * The RGB data type definition below are defined
+ * to follow Errata i819.
+ * The initial values were taken from:
+ * VPDMA_data_type_mapping_v0.2vayu_c.pdf
+ * But some of the ARGB definition appeared to be wrong
+ * in the document also. As they would yield RGBA instead.
+ * They have been corrected based on experimentation.
+ */
+#define DATA_TYPE_RGB16_565			0x10
+#define DATA_TYPE_ARGB_1555			0x13
+#define DATA_TYPE_ARGB_4444			0x14
+#define DATA_TYPE_RGBA_5551			0x11
+#define DATA_TYPE_RGBA_4444			0x12
+#define DATA_TYPE_ARGB24_6666			0x18
+#define DATA_TYPE_RGB24_888			0x16
+#define DATA_TYPE_ARGB32_8888			0x17
+#define DATA_TYPE_RGBA24_6666			0x15
+#define DATA_TYPE_RGBA32_8888			0x19
+#define DATA_TYPE_BGR16_565			0x0
+#define DATA_TYPE_ABGR_1555			0x3
+#define DATA_TYPE_ABGR_4444			0x4
+#define DATA_TYPE_BGRA_5551			0x1
+#define DATA_TYPE_BGRA_4444			0x2
+#define DATA_TYPE_ABGR24_6666			0x8
+#define DATA_TYPE_BGR24_888			0x6
+#define DATA_TYPE_ABGR32_8888			0x7
+#define DATA_TYPE_BGRA24_6666			0x5
+#define DATA_TYPE_BGRA32_8888			0x9
+
+#define DATA_TYPE_MV				0x3
+
+/* VPDMA channel numbers, some are common between VIP/VPE and appear twice */
+#define	VPE_CHAN_NUM_LUMA1_IN		0
+#define	VPE_CHAN_NUM_CHROMA1_IN		1
+#define	VPE_CHAN_NUM_LUMA2_IN		2
+#define	VPE_CHAN_NUM_CHROMA2_IN		3
+#define	VPE_CHAN_NUM_LUMA3_IN		4
+#define	VPE_CHAN_NUM_CHROMA3_IN		5
+#define	VPE_CHAN_NUM_MV_IN		12
+#define	VPE_CHAN_NUM_MV_OUT		15
+#define VIP1_CHAN_NUM_MULT_PORT_A_SRC0	38
+#define VIP1_CHAN_NUM_MULT_ANC_A_SRC0	70
+#define	VPE_CHAN_NUM_LUMA_OUT		102
+#define	VPE_CHAN_NUM_CHROMA_OUT		103
+#define VIP1_CHAN_NUM_PORT_A_LUMA	102
+#define VIP1_CHAN_NUM_PORT_A_CHROMA	103
+#define	VPE_CHAN_NUM_RGB_OUT		106
+#define VIP1_CHAN_NUM_PORT_A_RGB	106
+#define VIP1_CHAN_NUM_PORT_B_RGB	107
+/*
+ * a VPDMA address data block payload for a configuration descriptor needs to
+ * have each sub block length as a multiple of 16 bytes. Therefore, the overall
+ * size of the payload also needs to be a multiple of 16 bytes. The sub block
+ * lengths should be ensured to be aligned by the VPDMA user.
+ */
+#define VPDMA_ADB_SIZE_ALIGN		0x0f
+
+/*
+ * data transfer descriptor
+ */
+struct vpdma_dtd {
+	u32			type_ctl_stride;
+	union {
+		u32		xfer_length_height;
+		u32		w1;
+	};
+	u32			start_addr;
+	u32			pkt_ctl;
+	union {
+		u32		frame_width_height;	/* inbound */
+		u32		desc_write_addr;	/* outbound */
+	};
+	union {
+		u32		start_h_v;		/* inbound */
+		u32		max_width_height;	/* outbound */
+	};
+	u32			client_attr0;
+	u32			client_attr1;
+};
+
+/* Data Transfer Descriptor specifics */
+#define DTD_NO_NOTIFY		0
+#define DTD_NOTIFY		1
+
+#define DTD_PKT_TYPE		0xa
+#define DTD_DIR_IN		0
+#define DTD_DIR_OUT		1
+
+/* type_ctl_stride */
+#define DTD_DATA_TYPE_MASK	0x3f
+#define DTD_DATA_TYPE_SHFT	26
+#define DTD_NOTIFY_MASK		0x01
+#define DTD_NOTIFY_SHFT		25
+#define DTD_FIELD_MASK		0x01
+#define DTD_FIELD_SHFT		24
+#define DTD_1D_MASK		0x01
+#define DTD_1D_SHFT		23
+#define DTD_EVEN_LINE_SKIP_MASK	0x01
+#define DTD_EVEN_LINE_SKIP_SHFT	20
+#define DTD_ODD_LINE_SKIP_MASK	0x01
+#define DTD_ODD_LINE_SKIP_SHFT	16
+#define DTD_LINE_STRIDE_MASK	0xffff
+#define DTD_LINE_STRIDE_SHFT	0
+
+/* xfer_length_height */
+#define DTD_LINE_LENGTH_MASK	0xffff
+#define DTD_LINE_LENGTH_SHFT	16
+#define DTD_XFER_HEIGHT_MASK	0xffff
+#define DTD_XFER_HEIGHT_SHFT	0
+
+/* pkt_ctl */
+#define DTD_PKT_TYPE_MASK	0x1f
+#define DTD_PKT_TYPE_SHFT	27
+#define DTD_MODE_MASK		0x01
+#define DTD_MODE_SHFT		26
+#define DTD_DIR_MASK		0x01
+#define DTD_DIR_SHFT		25
+#define DTD_CHAN_MASK		0x01ff
+#define DTD_CHAN_SHFT		16
+#define DTD_PRI_MASK		0x0f
+#define DTD_PRI_SHFT		9
+#define DTD_NEXT_CHAN_MASK	0x01ff
+#define DTD_NEXT_CHAN_SHFT	0
+
+/* frame_width_height */
+#define DTD_FRAME_WIDTH_MASK	0xffff
+#define DTD_FRAME_WIDTH_SHFT	16
+#define DTD_FRAME_HEIGHT_MASK	0xffff
+#define DTD_FRAME_HEIGHT_SHFT	0
+
+/* start_h_v */
+#define DTD_H_START_MASK	0xffff
+#define DTD_H_START_SHFT	16
+#define DTD_V_START_MASK	0xffff
+#define DTD_V_START_SHFT	0
+
+#define DTD_DESC_START_MASK	0xffffffe0
+#define DTD_DESC_START_SHIFT	5
+#define DTD_WRITE_DESC_MASK	0x01
+#define DTD_WRITE_DESC_SHIFT	2
+#define DTD_DROP_DATA_MASK	0x01
+#define DTD_DROP_DATA_SHIFT	1
+#define DTD_USE_DESC_MASK	0x01
+#define DTD_USE_DESC_SHIFT	0
+
+/* max_width_height */
+#define DTD_MAX_WIDTH_MASK	0x07
+#define DTD_MAX_WIDTH_SHFT	4
+#define DTD_MAX_HEIGHT_MASK	0x07
+#define DTD_MAX_HEIGHT_SHFT	0
+
+static inline u32 dtd_type_ctl_stride(int type, bool notify, int field,
+			bool one_d, bool even_line_skip, bool odd_line_skip,
+			int line_stride)
+{
+	return (type << DTD_DATA_TYPE_SHFT) | (notify << DTD_NOTIFY_SHFT) |
+		(field << DTD_FIELD_SHFT) | (one_d << DTD_1D_SHFT) |
+		(even_line_skip << DTD_EVEN_LINE_SKIP_SHFT) |
+		(odd_line_skip << DTD_ODD_LINE_SKIP_SHFT) |
+		line_stride;
+}
+
+static inline u32 dtd_xfer_length_height(int line_length, int xfer_height)
+{
+	return (line_length << DTD_LINE_LENGTH_SHFT) | xfer_height;
+}
+
+static inline u32 dtd_pkt_ctl(bool mode, bool dir, int chan, int pri,
+			int next_chan)
+{
+	return (DTD_PKT_TYPE << DTD_PKT_TYPE_SHFT) | (mode << DTD_MODE_SHFT) |
+		(dir << DTD_DIR_SHFT) | (chan << DTD_CHAN_SHFT) |
+		(pri << DTD_PRI_SHFT) | next_chan;
+}
+
+static inline u32 dtd_frame_width_height(int width, int height)
+{
+	return (width << DTD_FRAME_WIDTH_SHFT) | height;
+}
+
+static inline u32 dtd_desc_write_addr(unsigned int addr, bool write_desc,
+			bool drop_data, bool use_desc)
+{
+	return (addr & DTD_DESC_START_MASK) |
+		(write_desc << DTD_WRITE_DESC_SHIFT) |
+		(drop_data << DTD_DROP_DATA_SHIFT) |
+		use_desc;
+}
+
+static inline u32 dtd_start_h_v(int h_start, int v_start)
+{
+	return (h_start << DTD_H_START_SHFT) | v_start;
+}
+
+static inline u32 dtd_max_width_height(int max_width, int max_height)
+{
+	return (max_width << DTD_MAX_WIDTH_SHFT) | max_height;
+}
+
+static inline int dtd_get_data_type(struct vpdma_dtd *dtd)
+{
+	return dtd->type_ctl_stride >> DTD_DATA_TYPE_SHFT;
+}
+
+static inline bool dtd_get_notify(struct vpdma_dtd *dtd)
+{
+	return (dtd->type_ctl_stride >> DTD_NOTIFY_SHFT) & DTD_NOTIFY_MASK;
+}
+
+static inline int dtd_get_field(struct vpdma_dtd *dtd)
+{
+	return (dtd->type_ctl_stride >> DTD_FIELD_SHFT) & DTD_FIELD_MASK;
+}
+
+static inline bool dtd_get_1d(struct vpdma_dtd *dtd)
+{
+	return (dtd->type_ctl_stride >> DTD_1D_SHFT) & DTD_1D_MASK;
+}
+
+static inline bool dtd_get_even_line_skip(struct vpdma_dtd *dtd)
+{
+	return (dtd->type_ctl_stride >> DTD_EVEN_LINE_SKIP_SHFT)
+		& DTD_EVEN_LINE_SKIP_MASK;
+}
+
+static inline bool dtd_get_odd_line_skip(struct vpdma_dtd *dtd)
+{
+	return (dtd->type_ctl_stride >> DTD_ODD_LINE_SKIP_SHFT)
+		& DTD_ODD_LINE_SKIP_MASK;
+}
+
+static inline int dtd_get_line_stride(struct vpdma_dtd *dtd)
+{
+	return dtd->type_ctl_stride & DTD_LINE_STRIDE_MASK;
+}
+
+static inline int dtd_get_line_length(struct vpdma_dtd *dtd)
+{
+	return dtd->xfer_length_height >> DTD_LINE_LENGTH_SHFT;
+}
+
+static inline int dtd_get_xfer_height(struct vpdma_dtd *dtd)
+{
+	return dtd->xfer_length_height & DTD_XFER_HEIGHT_MASK;
+}
+
+static inline int dtd_get_pkt_type(struct vpdma_dtd *dtd)
+{
+	return dtd->pkt_ctl >> DTD_PKT_TYPE_SHFT;
+}
+
+static inline bool dtd_get_mode(struct vpdma_dtd *dtd)
+{
+	return (dtd->pkt_ctl >> DTD_MODE_SHFT) & DTD_MODE_MASK;
+}
+
+static inline bool dtd_get_dir(struct vpdma_dtd *dtd)
+{
+	return (dtd->pkt_ctl >> DTD_DIR_SHFT) & DTD_DIR_MASK;
+}
+
+static inline int dtd_get_chan(struct vpdma_dtd *dtd)
+{
+	return (dtd->pkt_ctl >> DTD_CHAN_SHFT) & DTD_CHAN_MASK;
+}
+
+static inline int dtd_get_priority(struct vpdma_dtd *dtd)
+{
+	return (dtd->pkt_ctl >> DTD_PRI_SHFT) & DTD_PRI_MASK;
+}
+
+static inline int dtd_get_next_chan(struct vpdma_dtd *dtd)
+{
+	return (dtd->pkt_ctl >> DTD_NEXT_CHAN_SHFT) & DTD_NEXT_CHAN_MASK;
+}
+
+static inline int dtd_get_frame_width(struct vpdma_dtd *dtd)
+{
+	return dtd->frame_width_height >> DTD_FRAME_WIDTH_SHFT;
+}
+
+static inline int dtd_get_frame_height(struct vpdma_dtd *dtd)
+{
+	return dtd->frame_width_height & DTD_FRAME_HEIGHT_MASK;
+}
+
+static inline int dtd_get_desc_write_addr(struct vpdma_dtd *dtd)
+{
+	return dtd->desc_write_addr & DTD_DESC_START_MASK;
+}
+
+static inline bool dtd_get_write_desc(struct vpdma_dtd *dtd)
+{
+	return (dtd->desc_write_addr >> DTD_WRITE_DESC_SHIFT) &
+							DTD_WRITE_DESC_MASK;
+}
+
+static inline bool dtd_get_drop_data(struct vpdma_dtd *dtd)
+{
+	return (dtd->desc_write_addr >> DTD_DROP_DATA_SHIFT) &
+							DTD_DROP_DATA_MASK;
+}
+
+static inline bool dtd_get_use_desc(struct vpdma_dtd *dtd)
+{
+	return dtd->desc_write_addr & DTD_USE_DESC_MASK;
+}
+
+static inline int dtd_get_h_start(struct vpdma_dtd *dtd)
+{
+	return dtd->start_h_v >> DTD_H_START_SHFT;
+}
+
+static inline int dtd_get_v_start(struct vpdma_dtd *dtd)
+{
+	return dtd->start_h_v & DTD_V_START_MASK;
+}
+
+static inline int dtd_get_max_width(struct vpdma_dtd *dtd)
+{
+	return (dtd->max_width_height >> DTD_MAX_WIDTH_SHFT) &
+							DTD_MAX_WIDTH_MASK;
+}
+
+static inline int dtd_get_max_height(struct vpdma_dtd *dtd)
+{
+	return (dtd->max_width_height >> DTD_MAX_HEIGHT_SHFT) &
+							DTD_MAX_HEIGHT_MASK;
+}
+
+/*
+ * configuration descriptor
+ */
+struct vpdma_cfd {
+	union {
+		u32	dest_addr_offset;
+		u32	w0;
+	};
+	union {
+		u32	block_len;		/* in words */
+		u32	w1;
+	};
+	u32		payload_addr;
+	u32		ctl_payload_len;	/* in words */
+};
+
+/* Configuration descriptor specifics */
+
+#define CFD_PKT_TYPE		0xb
+
+#define CFD_DIRECT		1
+#define CFD_INDIRECT		0
+#define CFD_CLS_ADB		0
+#define CFD_CLS_BLOCK		1
+
+/* block_len */
+#define CFD__BLOCK_LEN_MASK	0xffff
+#define CFD__BLOCK_LEN_SHFT	0
+
+/* ctl_payload_len */
+#define CFD_PKT_TYPE_MASK	0x1f
+#define CFD_PKT_TYPE_SHFT	27
+#define CFD_DIRECT_MASK		0x01
+#define CFD_DIRECT_SHFT		26
+#define CFD_CLASS_MASK		0x03
+#define CFD_CLASS_SHFT		24
+#define CFD_DEST_MASK		0xff
+#define CFD_DEST_SHFT		16
+#define CFD_PAYLOAD_LEN_MASK	0xffff
+#define CFD_PAYLOAD_LEN_SHFT	0
+
+static inline u32 cfd_pkt_payload_len(bool direct, int cls, int dest,
+		int payload_len)
+{
+	return (CFD_PKT_TYPE << CFD_PKT_TYPE_SHFT) |
+		(direct << CFD_DIRECT_SHFT) |
+		(cls << CFD_CLASS_SHFT) |
+		(dest << CFD_DEST_SHFT) |
+		payload_len;
+}
+
+static inline int cfd_get_pkt_type(struct vpdma_cfd *cfd)
+{
+	return cfd->ctl_payload_len >> CFD_PKT_TYPE_SHFT;
+}
+
+static inline bool cfd_get_direct(struct vpdma_cfd *cfd)
+{
+	return (cfd->ctl_payload_len >> CFD_DIRECT_SHFT) & CFD_DIRECT_MASK;
+}
+
+static inline bool cfd_get_class(struct vpdma_cfd *cfd)
+{
+	return (cfd->ctl_payload_len >> CFD_CLASS_SHFT) & CFD_CLASS_MASK;
+}
+
+static inline int cfd_get_dest(struct vpdma_cfd *cfd)
+{
+	return (cfd->ctl_payload_len >> CFD_DEST_SHFT) & CFD_DEST_MASK;
+}
+
+static inline int cfd_get_payload_len(struct vpdma_cfd *cfd)
+{
+	return cfd->ctl_payload_len & CFD_PAYLOAD_LEN_MASK;
+}
+
+/*
+ * control descriptor
+ */
+struct vpdma_ctd {
+	union {
+		u32	timer_value;
+		u32	list_addr;
+		u32	w0;
+	};
+	union {
+		u32	pixel_line_count;
+		u32	list_size;
+		u32	w1;
+	};
+	union {
+		u32	event;
+		u32	fid_ctl;
+		u32	w2;
+	};
+	u32		type_source_ctl;
+};
+
+/* control descriptor types */
+#define CTD_TYPE_SYNC_ON_CLIENT		0
+#define CTD_TYPE_SYNC_ON_LIST		1
+#define CTD_TYPE_SYNC_ON_EXT		2
+#define CTD_TYPE_SYNC_ON_LM_TIMER	3
+#define CTD_TYPE_SYNC_ON_CHANNEL	4
+#define CTD_TYPE_CHNG_CLIENT_IRQ	5
+#define CTD_TYPE_SEND_IRQ		6
+#define CTD_TYPE_RELOAD_LIST		7
+#define CTD_TYPE_ABORT_CHANNEL		8
+
+#define CTD_PKT_TYPE		0xc
+
+/* timer_value */
+#define CTD_TIMER_VALUE_MASK	0xffff
+#define CTD_TIMER_VALUE_SHFT	0
+
+/* pixel_line_count */
+#define CTD_PIXEL_COUNT_MASK	0xffff
+#define CTD_PIXEL_COUNT_SHFT	16
+#define CTD_LINE_COUNT_MASK	0xffff
+#define CTD_LINE_COUNT_SHFT	0
+
+/* list_size */
+#define CTD_LIST_SIZE_MASK	0xffff
+#define CTD_LIST_SIZE_SHFT	0
+
+/* event */
+#define CTD_EVENT_MASK		0x0f
+#define CTD_EVENT_SHFT		0
+
+/* fid_ctl */
+#define CTD_FID2_MASK		0x03
+#define CTD_FID2_SHFT		4
+#define CTD_FID1_MASK		0x03
+#define CTD_FID1_SHFT		2
+#define CTD_FID0_MASK		0x03
+#define CTD_FID0_SHFT		0
+
+/* type_source_ctl */
+#define CTD_PKT_TYPE_MASK	0x1f
+#define CTD_PKT_TYPE_SHFT	27
+#define CTD_SOURCE_MASK		0xff
+#define CTD_SOURCE_SHFT		16
+#define CTD_CONTROL_MASK	0x0f
+#define CTD_CONTROL_SHFT	0
+
+static inline u32 ctd_pixel_line_count(int pixel_count, int line_count)
+{
+	return (pixel_count << CTD_PIXEL_COUNT_SHFT) | line_count;
+}
+
+static inline u32 ctd_set_fid_ctl(int fid0, int fid1, int fid2)
+{
+	return (fid2 << CTD_FID2_SHFT) | (fid1 << CTD_FID1_SHFT) | fid0;
+}
+
+static inline u32 ctd_type_source_ctl(int source, int control)
+{
+	return (CTD_PKT_TYPE << CTD_PKT_TYPE_SHFT) |
+		(source << CTD_SOURCE_SHFT) | control;
+}
+
+static inline u32 ctd_get_pixel_count(struct vpdma_ctd *ctd)
+{
+	return ctd->pixel_line_count >> CTD_PIXEL_COUNT_SHFT;
+}
+
+static inline int ctd_get_line_count(struct vpdma_ctd *ctd)
+{
+	return ctd->pixel_line_count & CTD_LINE_COUNT_MASK;
+}
+
+static inline int ctd_get_event(struct vpdma_ctd *ctd)
+{
+	return ctd->event & CTD_EVENT_MASK;
+}
+
+static inline int ctd_get_fid2_ctl(struct vpdma_ctd *ctd)
+{
+	return (ctd->fid_ctl >> CTD_FID2_SHFT) & CTD_FID2_MASK;
+}
+
+static inline int ctd_get_fid1_ctl(struct vpdma_ctd *ctd)
+{
+	return (ctd->fid_ctl >> CTD_FID1_SHFT) & CTD_FID1_MASK;
+}
+
+static inline int ctd_get_fid0_ctl(struct vpdma_ctd *ctd)
+{
+	return ctd->fid_ctl & CTD_FID2_MASK;
+}
+
+static inline int ctd_get_pkt_type(struct vpdma_ctd *ctd)
+{
+	return ctd->type_source_ctl >> CTD_PKT_TYPE_SHFT;
+}
+
+static inline int ctd_get_source(struct vpdma_ctd *ctd)
+{
+	return (ctd->type_source_ctl >> CTD_SOURCE_SHFT) & CTD_SOURCE_MASK;
+}
+
+static inline int ctd_get_ctl(struct vpdma_ctd *ctd)
+{
+	return ctd->type_source_ctl & CTD_CONTROL_MASK;
+}
+
+#endif

linux-7.2.3/drivers/media/platform/ti/vpe/vpe_regs.h

@@ -0,0 +1,306 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2013 Texas Instruments Inc.
+ *
+ * David Griego, <dagriego@biglakesoftware.com>
+ * Dale Farnsworth, <dale@farnsworth.org>
+ * Archit Taneja, <archit@ti.com>
+ */
+
+#ifndef __TI_VPE_REGS_H
+#define __TI_VPE_REGS_H
+
+/* VPE register offsets and field selectors */
+
+/* VPE top level regs */
+#define VPE_PID				0x0000
+#define VPE_PID_MINOR_MASK		0x3f
+#define VPE_PID_MINOR_SHIFT		0
+#define VPE_PID_CUSTOM_MASK		0x03
+#define VPE_PID_CUSTOM_SHIFT		6
+#define VPE_PID_MAJOR_MASK		0x07
+#define VPE_PID_MAJOR_SHIFT		8
+#define VPE_PID_RTL_MASK		0x1f
+#define VPE_PID_RTL_SHIFT		11
+#define VPE_PID_FUNC_MASK		0xfff
+#define VPE_PID_FUNC_SHIFT		16
+#define VPE_PID_SCHEME_MASK		0x03
+#define VPE_PID_SCHEME_SHIFT		30
+
+#define VPE_SYSCONFIG			0x0010
+#define VPE_SYSCONFIG_IDLE_MASK		0x03
+#define VPE_SYSCONFIG_IDLE_SHIFT	2
+#define VPE_SYSCONFIG_STANDBY_MASK	0x03
+#define VPE_SYSCONFIG_STANDBY_SHIFT	4
+#define VPE_FORCE_IDLE_MODE		0
+#define VPE_NO_IDLE_MODE		1
+#define VPE_SMART_IDLE_MODE		2
+#define VPE_SMART_IDLE_WAKEUP_MODE	3
+#define VPE_FORCE_STANDBY_MODE		0
+#define VPE_NO_STANDBY_MODE		1
+#define VPE_SMART_STANDBY_MODE		2
+#define VPE_SMART_STANDBY_WAKEUP_MODE	3
+
+#define VPE_INT0_STATUS0_RAW_SET	0x0020
+#define VPE_INT0_STATUS0_RAW		VPE_INT0_STATUS0_RAW_SET
+#define VPE_INT0_STATUS0_CLR		0x0028
+#define VPE_INT0_STATUS0		VPE_INT0_STATUS0_CLR
+#define VPE_INT0_ENABLE0_SET		0x0030
+#define VPE_INT0_ENABLE0		VPE_INT0_ENABLE0_SET
+#define VPE_INT0_ENABLE0_CLR		0x0038
+#define VPE_INT0_LIST0_COMPLETE		BIT(0)
+#define VPE_INT0_LIST0_NOTIFY		BIT(1)
+#define VPE_INT0_LIST1_COMPLETE		BIT(2)
+#define VPE_INT0_LIST1_NOTIFY		BIT(3)
+#define VPE_INT0_LIST2_COMPLETE		BIT(4)
+#define VPE_INT0_LIST2_NOTIFY		BIT(5)
+#define VPE_INT0_LIST3_COMPLETE		BIT(6)
+#define VPE_INT0_LIST3_NOTIFY		BIT(7)
+#define VPE_INT0_LIST4_COMPLETE		BIT(8)
+#define VPE_INT0_LIST4_NOTIFY		BIT(9)
+#define VPE_INT0_LIST5_COMPLETE		BIT(10)
+#define VPE_INT0_LIST5_NOTIFY		BIT(11)
+#define VPE_INT0_LIST6_COMPLETE		BIT(12)
+#define VPE_INT0_LIST6_NOTIFY		BIT(13)
+#define VPE_INT0_LIST7_COMPLETE		BIT(14)
+#define VPE_INT0_LIST7_NOTIFY		BIT(15)
+#define VPE_INT0_DESCRIPTOR		BIT(16)
+#define VPE_DEI_FMD_INT			BIT(18)
+
+#define VPE_INT0_STATUS1_RAW_SET	0x0024
+#define VPE_INT0_STATUS1_RAW		VPE_INT0_STATUS1_RAW_SET
+#define VPE_INT0_STATUS1_CLR		0x002c
+#define VPE_INT0_STATUS1		VPE_INT0_STATUS1_CLR
+#define VPE_INT0_ENABLE1_SET		0x0034
+#define VPE_INT0_ENABLE1		VPE_INT0_ENABLE1_SET
+#define VPE_INT0_ENABLE1_CLR		0x003c
+#define VPE_INT0_CHANNEL_GROUP0		BIT(0)
+#define VPE_INT0_CHANNEL_GROUP1		BIT(1)
+#define VPE_INT0_CHANNEL_GROUP2		BIT(2)
+#define VPE_INT0_CHANNEL_GROUP3		BIT(3)
+#define VPE_INT0_CHANNEL_GROUP4		BIT(4)
+#define VPE_INT0_CHANNEL_GROUP5		BIT(5)
+#define VPE_INT0_CLIENT			BIT(7)
+#define VPE_DEI_ERROR_INT		BIT(16)
+#define VPE_DS1_UV_ERROR_INT		BIT(22)
+
+#define VPE_INTC_EOI			0x00a0
+
+#define VPE_CLK_ENABLE			0x0100
+#define VPE_VPEDMA_CLK_ENABLE		BIT(0)
+#define VPE_DATA_PATH_CLK_ENABLE	BIT(1)
+
+#define VPE_CLK_RESET			0x0104
+#define VPE_VPDMA_CLK_RESET_MASK	0x1
+#define VPE_VPDMA_CLK_RESET_SHIFT	0
+#define VPE_DATA_PATH_CLK_RESET_MASK	0x1
+#define VPE_DATA_PATH_CLK_RESET_SHIFT	1
+#define VPE_MAIN_RESET_MASK		0x1
+#define VPE_MAIN_RESET_SHIFT		31
+
+#define VPE_CLK_FORMAT_SELECT		0x010c
+#define VPE_CSC_SRC_SELECT_MASK		0x03
+#define VPE_CSC_SRC_SELECT_SHIFT	0
+#define VPE_RGB_OUT_SELECT		BIT(8)
+#define VPE_DS_SRC_SELECT_MASK		0x07
+#define VPE_DS_SRC_SELECT_SHIFT		9
+#define VPE_DS_BYPASS			BIT(16)
+#define VPE_COLOR_SEPARATE_422		BIT(18)
+
+#define VPE_DS_SRC_DEI_SCALER		(5 << VPE_DS_SRC_SELECT_SHIFT)
+#define VPE_CSC_SRC_DEI_SCALER		(3 << VPE_CSC_SRC_SELECT_SHIFT)
+
+#define VPE_CLK_RANGE_MAP		0x011c
+#define VPE_RANGE_RANGE_MAP_Y_MASK	0x07
+#define VPE_RANGE_RANGE_MAP_Y_SHIFT	0
+#define VPE_RANGE_RANGE_MAP_UV_MASK	0x07
+#define VPE_RANGE_RANGE_MAP_UV_SHIFT	3
+#define VPE_RANGE_MAP_ON		BIT(6)
+#define VPE_RANGE_REDUCTION_ON		BIT(28)
+
+/* VPE chrominance upsampler regs */
+#define VPE_US1_R0			0x0304
+#define VPE_US2_R0			0x0404
+#define VPE_US3_R0			0x0504
+#define VPE_US_C1_MASK			0x3fff
+#define VPE_US_C1_SHIFT			2
+#define VPE_US_C0_MASK			0x3fff
+#define VPE_US_C0_SHIFT			18
+#define VPE_US_MODE_MASK		0x03
+#define VPE_US_MODE_SHIFT		16
+#define VPE_ANCHOR_FID0_C1_MASK		0x3fff
+#define VPE_ANCHOR_FID0_C1_SHIFT	2
+#define VPE_ANCHOR_FID0_C0_MASK		0x3fff
+#define VPE_ANCHOR_FID0_C0_SHIFT	18
+
+#define VPE_US1_R1			0x0308
+#define VPE_US2_R1			0x0408
+#define VPE_US3_R1			0x0508
+#define VPE_ANCHOR_FID0_C3_MASK		0x3fff
+#define VPE_ANCHOR_FID0_C3_SHIFT	2
+#define VPE_ANCHOR_FID0_C2_MASK		0x3fff
+#define VPE_ANCHOR_FID0_C2_SHIFT	18
+
+#define VPE_US1_R2			0x030c
+#define VPE_US2_R2			0x040c
+#define VPE_US3_R2			0x050c
+#define VPE_INTERP_FID0_C1_MASK		0x3fff
+#define VPE_INTERP_FID0_C1_SHIFT	2
+#define VPE_INTERP_FID0_C0_MASK		0x3fff
+#define VPE_INTERP_FID0_C0_SHIFT	18
+
+#define VPE_US1_R3			0x0310
+#define VPE_US2_R3			0x0410
+#define VPE_US3_R3			0x0510
+#define VPE_INTERP_FID0_C3_MASK		0x3fff
+#define VPE_INTERP_FID0_C3_SHIFT	2
+#define VPE_INTERP_FID0_C2_MASK		0x3fff
+#define VPE_INTERP_FID0_C2_SHIFT	18
+
+#define VPE_US1_R4			0x0314
+#define VPE_US2_R4			0x0414
+#define VPE_US3_R4			0x0514
+#define VPE_ANCHOR_FID1_C1_MASK		0x3fff
+#define VPE_ANCHOR_FID1_C1_SHIFT	2
+#define VPE_ANCHOR_FID1_C0_MASK		0x3fff
+#define VPE_ANCHOR_FID1_C0_SHIFT	18
+
+#define VPE_US1_R5			0x0318
+#define VPE_US2_R5			0x0418
+#define VPE_US3_R5			0x0518
+#define VPE_ANCHOR_FID1_C3_MASK		0x3fff
+#define VPE_ANCHOR_FID1_C3_SHIFT	2
+#define VPE_ANCHOR_FID1_C2_MASK		0x3fff
+#define VPE_ANCHOR_FID1_C2_SHIFT	18
+
+#define VPE_US1_R6			0x031c
+#define VPE_US2_R6			0x041c
+#define VPE_US3_R6			0x051c
+#define VPE_INTERP_FID1_C1_MASK		0x3fff
+#define VPE_INTERP_FID1_C1_SHIFT	2
+#define VPE_INTERP_FID1_C0_MASK		0x3fff
+#define VPE_INTERP_FID1_C0_SHIFT	18
+
+#define VPE_US1_R7			0x0320
+#define VPE_US2_R7			0x0420
+#define VPE_US3_R7			0x0520
+#define VPE_INTERP_FID0_C3_MASK		0x3fff
+#define VPE_INTERP_FID0_C3_SHIFT	2
+#define VPE_INTERP_FID0_C2_MASK		0x3fff
+#define VPE_INTERP_FID0_C2_SHIFT	18
+
+/* VPE de-interlacer regs */
+#define VPE_DEI_FRAME_SIZE		0x0600
+#define VPE_DEI_WIDTH_MASK		0x07ff
+#define VPE_DEI_WIDTH_SHIFT		0
+#define VPE_DEI_HEIGHT_MASK		0x07ff
+#define VPE_DEI_HEIGHT_SHIFT		16
+#define VPE_DEI_INTERLACE_BYPASS	BIT(29)
+#define VPE_DEI_FIELD_FLUSH		BIT(30)
+#define VPE_DEI_PROGRESSIVE		BIT(31)
+
+#define VPE_MDT_BYPASS			0x0604
+#define VPE_MDT_TEMPMAX_BYPASS		BIT(0)
+#define VPE_MDT_SPATMAX_BYPASS		BIT(1)
+
+#define VPE_MDT_SF_THRESHOLD		0x0608
+#define VPE_MDT_SF_SC_THR1_MASK		0xff
+#define VPE_MDT_SF_SC_THR1_SHIFT	0
+#define VPE_MDT_SF_SC_THR2_MASK		0xff
+#define VPE_MDT_SF_SC_THR2_SHIFT	0
+#define VPE_MDT_SF_SC_THR3_MASK		0xff
+#define VPE_MDT_SF_SC_THR3_SHIFT	0
+
+#define VPE_EDI_CONFIG			0x060c
+#define VPE_EDI_INP_MODE_MASK		0x03
+#define VPE_EDI_INP_MODE_SHIFT		0
+#define VPE_EDI_ENABLE_3D		BIT(2)
+#define VPE_EDI_ENABLE_CHROMA_3D	BIT(3)
+#define VPE_EDI_CHROMA3D_COR_THR_MASK	0xff
+#define VPE_EDI_CHROMA3D_COR_THR_SHIFT	8
+#define VPE_EDI_DIR_COR_LOWER_THR_MASK	0xff
+#define VPE_EDI_DIR_COR_LOWER_THR_SHIFT	16
+#define VPE_EDI_COR_SCALE_FACTOR_MASK	0xff
+#define VPE_EDI_COR_SCALE_FACTOR_SHIFT	23
+
+#define VPE_DEI_EDI_LUT_R0		0x0610
+#define VPE_EDI_LUT0_MASK		0x1f
+#define VPE_EDI_LUT0_SHIFT		0
+#define VPE_EDI_LUT1_MASK		0x1f
+#define VPE_EDI_LUT1_SHIFT		8
+#define VPE_EDI_LUT2_MASK		0x1f
+#define VPE_EDI_LUT2_SHIFT		16
+#define VPE_EDI_LUT3_MASK		0x1f
+#define VPE_EDI_LUT3_SHIFT		24
+
+#define VPE_DEI_EDI_LUT_R1		0x0614
+#define VPE_EDI_LUT0_MASK		0x1f
+#define VPE_EDI_LUT0_SHIFT		0
+#define VPE_EDI_LUT1_MASK		0x1f
+#define VPE_EDI_LUT1_SHIFT		8
+#define VPE_EDI_LUT2_MASK		0x1f
+#define VPE_EDI_LUT2_SHIFT		16
+#define VPE_EDI_LUT3_MASK		0x1f
+#define VPE_EDI_LUT3_SHIFT		24
+
+#define VPE_DEI_EDI_LUT_R2		0x0618
+#define VPE_EDI_LUT4_MASK		0x1f
+#define VPE_EDI_LUT4_SHIFT		0
+#define VPE_EDI_LUT5_MASK		0x1f
+#define VPE_EDI_LUT5_SHIFT		8
+#define VPE_EDI_LUT6_MASK		0x1f
+#define VPE_EDI_LUT6_SHIFT		16
+#define VPE_EDI_LUT7_MASK		0x1f
+#define VPE_EDI_LUT7_SHIFT		24
+
+#define VPE_DEI_EDI_LUT_R3		0x061c
+#define VPE_EDI_LUT8_MASK		0x1f
+#define VPE_EDI_LUT8_SHIFT		0
+#define VPE_EDI_LUT9_MASK		0x1f
+#define VPE_EDI_LUT9_SHIFT		8
+#define VPE_EDI_LUT10_MASK		0x1f
+#define VPE_EDI_LUT10_SHIFT		16
+#define VPE_EDI_LUT11_MASK		0x1f
+#define VPE_EDI_LUT11_SHIFT		24
+
+#define VPE_DEI_FMD_WINDOW_R0		0x0620
+#define VPE_FMD_WINDOW_MINX_MASK	0x07ff
+#define VPE_FMD_WINDOW_MINX_SHIFT	0
+#define VPE_FMD_WINDOW_MAXX_MASK	0x07ff
+#define VPE_FMD_WINDOW_MAXX_SHIFT	16
+#define VPE_FMD_WINDOW_ENABLE		BIT(31)
+
+#define VPE_DEI_FMD_WINDOW_R1		0x0624
+#define VPE_FMD_WINDOW_MINY_MASK	0x07ff
+#define VPE_FMD_WINDOW_MINY_SHIFT	0
+#define VPE_FMD_WINDOW_MAXY_MASK	0x07ff
+#define VPE_FMD_WINDOW_MAXY_SHIFT	16
+
+#define VPE_DEI_FMD_CONTROL_R0		0x0628
+#define VPE_FMD_ENABLE			BIT(0)
+#define VPE_FMD_LOCK			BIT(1)
+#define VPE_FMD_JAM_DIR			BIT(2)
+#define VPE_FMD_BED_ENABLE		BIT(3)
+#define VPE_FMD_CAF_FIELD_THR_MASK	0xff
+#define VPE_FMD_CAF_FIELD_THR_SHIFT	16
+#define VPE_FMD_CAF_LINE_THR_MASK	0xff
+#define VPE_FMD_CAF_LINE_THR_SHIFT	24
+
+#define VPE_DEI_FMD_CONTROL_R1		0x062c
+#define VPE_FMD_CAF_THR_MASK		0x000fffff
+#define VPE_FMD_CAF_THR_SHIFT		0
+
+#define VPE_DEI_FMD_STATUS_R0		0x0630
+#define VPE_FMD_CAF_MASK		0x000fffff
+#define VPE_FMD_CAF_SHIFT		0
+#define VPE_FMD_RESET			BIT(24)
+
+#define VPE_DEI_FMD_STATUS_R1		0x0634
+#define VPE_FMD_FIELD_DIFF_MASK		0x0fffffff
+#define VPE_FMD_FIELD_DIFF_SHIFT	0
+
+#define VPE_DEI_FMD_STATUS_R2		0x0638
+#define VPE_FMD_FRAME_DIFF_MASK		0x000fffff
+#define VPE_FMD_FRAME_DIFF_SHIFT	0
+
+#endif