Resguardo inicial

linux-7.2.3/drivers/misc/amd-sbi/Kconfig

@@ -0,0 +1,22 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config AMD_SBRMI_I2C
+	tristate "AMD side band RMI support"
+	depends on I3C_OR_I2C
+	depends on ARM || ARM64 || COMPILE_TEST
+	select REGMAP_I2C
+	select REGMAP_I3C if I3C
+	help
+	  Side band RMI over I2C/I3C support for AMD out of band management.
+	  This driver is intended to run on the BMC, not the managed node.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called sbrmi-i2c.
+
+config AMD_SBRMI_HWMON
+	bool "SBRMI hardware monitoring"
+	depends on AMD_SBRMI_I2C && HWMON
+	depends on !(AMD_SBRMI_I2C=y && HWMON=m)
+	help
+	  This provides support for RMI device hardware monitoring. If enabled,
+	  a hardware monitoring device will be created for each socket in
+	  the system.

linux-7.2.3/drivers/misc/amd-sbi/Makefile

@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
+sbrmi-i2c-objs  		+= rmi-i2c.o rmi-core.o
+sbrmi-i2c-$(CONFIG_AMD_SBRMI_HWMON)	+= rmi-hwmon.o
+obj-$(CONFIG_AMD_SBRMI_I2C)	+= sbrmi-i2c.o

linux-7.2.3/drivers/misc/amd-sbi/rmi-core.c

@@ -0,0 +1,594 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * sbrmi-core.c - file defining SB-RMI protocols compliant
+ *		  AMD SoC device.
+ *
+ * Copyright (C) 2025 Advanced Micro Devices, Inc.
+ */
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/fs.h>
+#include <linux/i2c.h>
+#include <linux/miscdevice.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/regmap.h>
+#include "rmi-core.h"
+
+/* Mask for Status Register bit[1] */
+#define SW_ALERT_MASK	0x2
+/* Mask to check H/W Alert status bit */
+#define HW_ALERT_MASK	0x80
+
+/* Software Interrupt for triggering */
+#define START_CMD	0x80
+#define TRIGGER_MAILBOX	0x01
+
+/* Default message lengths as per APML command protocol */
+/* CPUID */
+#define CPUID_RD_DATA_LEN	0x8
+#define CPUID_WR_DATA_LEN	0x8
+#define CPUID_WR_DATA_LEN_EXT	0x9
+#define CPUID_RD_REG_LEN	0xa
+#define CPUID_WR_REG_LEN	0x9
+#define CPUID_WR_REG_LEN_EXT	0xa
+/* MSR */
+#define MSR_RD_REG_LEN		0xa
+#define MSR_WR_REG_LEN		0x8
+#define MSR_WR_REG_LEN_EXT	0x9
+#define MSR_RD_DATA_LEN		0x8
+#define MSR_WR_DATA_LEN		0x7
+#define MSR_WR_DATA_LEN_EXT	0x8
+
+/* CPUID MSR Command Ids */
+#define CPUID_MCA_CMD	0x73
+#define RD_CPUID_CMD	0x91
+#define RD_MCA_CMD	0x86
+
+/* CPUID MCAMSR mask & index */
+#define CPUID_MCA_THRD_INDEX	32
+#define CPUID_MCA_FUNC_MASK	GENMASK(31, 0)
+#define CPUID_EXT_FUNC_INDEX	48
+
+/* input for bulk write to CPUID protocol */
+struct cpu_msr_indata {
+	u8 wr_len;	/* const value */
+	u8 rd_len;	/* const value */
+	u8 proto_cmd;	/* const value */
+	u8 thread;	/* thread number */
+	union {
+		u8 reg_offset[4];	/* input value */
+		u32 value;
+	} __packed;
+	u8 ext; /* extended function */
+};
+
+/* input for bulk write to CPUID protocol for REV 0x21 */
+struct cpu_msr_indata_ext {
+	u8 wr_len;	/* const value */
+	u8 rd_len;	/* const value */
+	u8 proto_cmd;	/* const value */
+	u8 thread_lo;	/* thread number low */
+	u8 thread_hi;	/* thread number high */
+	union {
+		u8 reg_offset[4];	/* input value */
+		u32 value;
+	} __packed;
+	u8 ext; /* extended function */
+};
+
+/* output for bulk read from CPUID protocol */
+struct cpu_msr_outdata {
+	u8 num_bytes;	/* number of bytes return */
+	u8 status;	/* Protocol status code */
+	union {
+		u64 value;
+		u8 reg_data[8];
+	} __packed;
+};
+
+static inline void prepare_cpuid_input_message(struct cpu_msr_indata *input,
+					       u8 thread_id, u32 func,
+					       u8 ext_func)
+{
+	input->rd_len		= CPUID_RD_DATA_LEN;
+	input->wr_len		= CPUID_WR_DATA_LEN;
+	input->proto_cmd	= RD_CPUID_CMD;
+	input->thread		= thread_id << 1;
+	input->value		= func;
+	input->ext		= ext_func;
+}
+
+static inline void prepare_cpuid_input_message_ext(struct cpu_msr_indata_ext *input,
+						   u16 thread_id, u32 func,
+						   u8 ext_func)
+{
+	input->rd_len		= CPUID_RD_DATA_LEN;
+	input->wr_len		= CPUID_WR_DATA_LEN_EXT;
+	input->proto_cmd	= RD_CPUID_CMD;
+	input->thread_lo	= (thread_id & 0xFF) << 1;
+	input->thread_hi	= thread_id >> 8;
+	input->value		= func;
+	input->ext		= ext_func;
+}
+
+static inline void prepare_mca_msr_input_message(struct cpu_msr_indata *input,
+						 u8 thread_id, u32 data_in)
+{
+	input->rd_len		= MSR_RD_DATA_LEN;
+	input->wr_len		= MSR_WR_DATA_LEN;
+	input->proto_cmd	= RD_MCA_CMD;
+	input->thread		= thread_id << 1;
+	input->value		= data_in;
+}
+
+static inline void prepare_mca_msr_input_message_ext(struct cpu_msr_indata_ext *input,
+						     u16 thread_id, u32 data_in)
+{
+	input->rd_len		= MSR_RD_DATA_LEN;
+	input->wr_len		= MSR_WR_DATA_LEN_EXT;
+	input->proto_cmd	= RD_MCA_CMD;
+	input->thread_lo	= (thread_id & 0xFF) << 1;
+	input->thread_hi	= thread_id >> 8;
+	input->value		= data_in;
+}
+
+static int sbrmi_get_rev(struct sbrmi_data *data)
+{
+	unsigned int rev;
+	u16 offset = SBRMI_REV;
+	int ret;
+
+	ret = regmap_read(data->regmap, offset, &rev);
+	if (ret < 0)
+		return ret;
+
+	data->rev = rev;
+	return 0;
+}
+
+static int rmi_cpuid_input(struct sbrmi_data *data, struct apml_cpuid_msg *msg,
+			   u16 thread)
+{
+	struct cpu_msr_indata input = {0};
+	int val = 0, ret;
+
+	/* Thread > 127, Thread128 CS register, 1'b1 needs to be set to 1 */
+	if (thread > 127) {
+		thread -= 128;
+		val = 1;
+	}
+
+	ret = regmap_write(data->regmap, SBRMI_THREAD128CS, val);
+	if (ret < 0)
+		return ret;
+
+	prepare_cpuid_input_message(&input, thread,
+				    msg->cpu_in_out & CPUID_MCA_FUNC_MASK,
+				    msg->cpu_in_out >> CPUID_EXT_FUNC_INDEX);
+
+	return regmap_bulk_write(data->regmap, CPUID_MCA_CMD,
+				 &input, CPUID_WR_REG_LEN);
+}
+
+static int rmi_cpuid_input_ext(struct sbrmi_data *data, struct apml_cpuid_msg *msg,
+			       u16 thread)
+{
+	struct cpu_msr_indata_ext input = {0};
+
+	prepare_cpuid_input_message_ext(&input, thread,
+					msg->cpu_in_out & CPUID_MCA_FUNC_MASK,
+					msg->cpu_in_out >> CPUID_EXT_FUNC_INDEX);
+
+	return regmap_bulk_write(data->regmap, CPUID_MCA_CMD,
+				 &input, CPUID_WR_REG_LEN_EXT);
+}
+
+/* Read CPUID function protocol */
+static int rmi_cpuid_read(struct sbrmi_data *data,
+			  struct apml_cpuid_msg *msg)
+{
+	struct cpu_msr_outdata output = {0};
+	int ret, hw_status;
+	u16 thread;
+
+	mutex_lock(&data->lock);
+	/* cache the rev value to identify if protocol is supported or not */
+	if (!data->rev) {
+		ret = sbrmi_get_rev(data);
+		if (ret < 0)
+			goto exit_unlock;
+	}
+
+	/* Extract thread from the input msg structure */
+	thread = msg->cpu_in_out >> CPUID_MCA_THRD_INDEX;
+
+	switch (data->rev) {
+	case 0x10:
+		/* CPUID protocol for REV 0x10 is not supported*/
+		ret = -EOPNOTSUPP;
+		goto exit_unlock;
+	case 0x20:
+		ret = rmi_cpuid_input(data, msg, thread);
+		if (ret)
+			goto exit_unlock;
+		break;
+	case 0x21:
+	case 0x31:
+		ret = rmi_cpuid_input_ext(data, msg, thread);
+		if (ret)
+			goto exit_unlock;
+		break;
+	default:
+		ret = -EOPNOTSUPP;
+		goto exit_unlock;
+	}
+
+	/*
+	 * For RMI Rev 0x20, new h/w status bit is introduced. which is used
+	 * by firmware to indicate completion of commands (0x71, 0x72, 0x73).
+	 * wait for the status bit to be set by the hardware before
+	 * reading the data out.
+	 */
+	ret = regmap_read_poll_timeout(data->regmap, SBRMI_STATUS, hw_status,
+				       hw_status & HW_ALERT_MASK, 500, 2000000);
+	if (ret)
+		goto exit_unlock;
+
+	ret = regmap_bulk_read(data->regmap, CPUID_MCA_CMD,
+			       &output, CPUID_RD_REG_LEN);
+	if (ret < 0)
+		goto exit_unlock;
+
+	ret = regmap_write(data->regmap, SBRMI_STATUS,
+			   HW_ALERT_MASK);
+	if (ret < 0)
+		goto exit_unlock;
+
+	if (output.num_bytes != CPUID_RD_REG_LEN - 1) {
+		ret = -EMSGSIZE;
+		goto exit_unlock;
+	}
+	if (output.status) {
+		ret = -EPROTOTYPE;
+		msg->fw_ret_code = output.status;
+		goto exit_unlock;
+	}
+	msg->cpu_in_out = output.value;
+exit_unlock:
+	if (ret < 0)
+		msg->cpu_in_out = 0;
+	mutex_unlock(&data->lock);
+	return ret;
+}
+
+static int rmi_mcamsr_input(struct sbrmi_data *data, struct apml_mcamsr_msg *msg,
+			    u16 thread)
+{
+	struct cpu_msr_indata input = {0};
+	int val = 0, ret;
+
+	/* Thread > 127, Thread128 CS register, 1'b1 needs to be set to 1 */
+	if (thread > 127) {
+		thread -= 128;
+		val = 1;
+	}
+
+	ret = regmap_write(data->regmap, SBRMI_THREAD128CS, val);
+	if (ret < 0)
+		return ret;
+
+	prepare_mca_msr_input_message(&input, thread,
+				      msg->mcamsr_in_out & CPUID_MCA_FUNC_MASK);
+
+	return regmap_bulk_write(data->regmap, CPUID_MCA_CMD,
+				 &input, MSR_WR_REG_LEN);
+}
+
+static int rmi_mcamsr_input_ext(struct sbrmi_data *data, struct apml_mcamsr_msg *msg,
+				u16 thread)
+{
+	struct cpu_msr_indata_ext input = {0};
+
+	prepare_mca_msr_input_message_ext(&input, thread,
+					  msg->mcamsr_in_out & CPUID_MCA_FUNC_MASK);
+
+	return regmap_bulk_write(data->regmap, CPUID_MCA_CMD,
+				 &input, MSR_WR_REG_LEN_EXT);
+}
+
+/* MCA MSR protocol */
+static int rmi_mca_msr_read(struct sbrmi_data *data,
+			    struct apml_mcamsr_msg  *msg)
+{
+	struct cpu_msr_outdata output = {0};
+	int ret;
+	int hw_status;
+	u16 thread;
+
+	mutex_lock(&data->lock);
+	/* cache the rev value to identify if protocol is supported or not */
+	if (!data->rev) {
+		ret = sbrmi_get_rev(data);
+		if (ret < 0)
+			goto exit_unlock;
+	}
+
+	/* Extract thread from the input msg structure */
+	thread = msg->mcamsr_in_out >> CPUID_MCA_THRD_INDEX;
+
+	switch (data->rev) {
+	case 0x10:
+		/* MCAMSR protocol for REV 0x10 is not supported*/
+		ret = -EOPNOTSUPP;
+		goto exit_unlock;
+	case 0x20:
+		ret = rmi_mcamsr_input(data, msg, thread);
+		if (ret)
+			goto exit_unlock;
+		break;
+	case 0x21:
+	case 0x31:
+		ret = rmi_mcamsr_input_ext(data, msg, thread);
+		if (ret)
+			goto exit_unlock;
+		break;
+	default:
+		ret = -EOPNOTSUPP;
+		goto exit_unlock;
+	}
+
+	/*
+	 * For RMI Rev 0x20, new h/w status bit is introduced. which is used
+	 * by firmware to indicate completion of commands (0x71, 0x72, 0x73).
+	 * wait for the status bit to be set by the hardware before
+	 * reading the data out.
+	 */
+	ret = regmap_read_poll_timeout(data->regmap, SBRMI_STATUS, hw_status,
+				       hw_status & HW_ALERT_MASK, 500, 2000000);
+	if (ret)
+		goto exit_unlock;
+
+	ret = regmap_bulk_read(data->regmap, CPUID_MCA_CMD,
+			       &output, MSR_RD_REG_LEN);
+	if (ret < 0)
+		goto exit_unlock;
+
+	ret = regmap_write(data->regmap, SBRMI_STATUS,
+			   HW_ALERT_MASK);
+	if (ret < 0)
+		goto exit_unlock;
+
+	if (output.num_bytes != MSR_RD_REG_LEN - 1) {
+		ret = -EMSGSIZE;
+		goto exit_unlock;
+	}
+	if (output.status) {
+		ret = -EPROTOTYPE;
+		msg->fw_ret_code = output.status;
+		goto exit_unlock;
+	}
+	msg->mcamsr_in_out = output.value;
+
+exit_unlock:
+	mutex_unlock(&data->lock);
+	return ret;
+}
+
+int rmi_mailbox_xfer(struct sbrmi_data *data,
+		     struct apml_mbox_msg *msg)
+{
+	unsigned int bytes, ec;
+	int i, ret;
+	int sw_status;
+	u8 byte;
+
+	mutex_lock(&data->lock);
+
+	msg->fw_ret_code = 0;
+
+	/* Indicate firmware a command is to be serviced */
+	ret = regmap_write(data->regmap, SBRMI_INBNDMSG7, START_CMD);
+	if (ret < 0)
+		goto exit_unlock;
+
+	/* Write the command to SBRMI::InBndMsg_inst0 */
+	ret = regmap_write(data->regmap, SBRMI_INBNDMSG0, msg->cmd);
+	if (ret < 0)
+		goto exit_unlock;
+
+	/*
+	 * For both read and write the initiator (BMC) writes
+	 * Command Data In[31:0] to SBRMI::InBndMsg_inst[4:1]
+	 * SBRMI_x3C(MSB):SBRMI_x39(LSB)
+	 */
+	for (i = 0; i < AMD_SBI_MB_DATA_SIZE; i++) {
+		byte = (msg->mb_in_out >> i * 8) & 0xff;
+		ret = regmap_write(data->regmap, SBRMI_INBNDMSG1 + i, byte);
+		if (ret < 0)
+			goto exit_unlock;
+	}
+
+	/*
+	 * Write 0x01 to SBRMI::SoftwareInterrupt to notify firmware to
+	 * perform the requested read or write command
+	 */
+	ret = regmap_write(data->regmap, SBRMI_SW_INTERRUPT, TRIGGER_MAILBOX);
+	if (ret < 0)
+		goto exit_unlock;
+
+	/*
+	 * Firmware will write SBRMI::Status[SwAlertSts]=1 to generate
+	 * an ALERT (if enabled) to initiator (BMC) to indicate completion
+	 * of the requested command
+	 */
+	ret = regmap_read_poll_timeout(data->regmap, SBRMI_STATUS, sw_status,
+				       sw_status & SW_ALERT_MASK, 500, 2000000);
+	if (ret)
+		goto exit_unlock;
+
+	ret = regmap_read(data->regmap, SBRMI_OUTBNDMSG7, &ec);
+	if (ret || ec)
+		goto exit_clear_alert;
+
+	/* Clear the input value before updating the output data */
+	msg->mb_in_out = 0;
+
+	/*
+	 * For a read operation, the initiator (BMC) reads the firmware
+	 * response Command Data Out[31:0] from SBRMI::OutBndMsg_inst[4:1]
+	 * {SBRMI_x34(MSB):SBRMI_x31(LSB)}.
+	 */
+	for (i = 0; i < AMD_SBI_MB_DATA_SIZE; i++) {
+		ret = regmap_read(data->regmap,
+				  SBRMI_OUTBNDMSG1 + i, &bytes);
+		if (ret < 0)
+			break;
+		msg->mb_in_out |= bytes << i * 8;
+	}
+
+exit_clear_alert:
+	/*
+	 * BMC must write 1'b1 to SBRMI::Status[SwAlertSts] to clear the
+	 * ALERT to initiator
+	 */
+	ret = regmap_write(data->regmap, SBRMI_STATUS,
+			   sw_status | SW_ALERT_MASK);
+	if (ec) {
+		ret = -EPROTOTYPE;
+		msg->fw_ret_code = ec;
+	}
+exit_unlock:
+	mutex_unlock(&data->lock);
+	return ret;
+}
+
+static int apml_rmi_reg_xfer(struct sbrmi_data *data,
+			     struct apml_reg_xfer_msg __user *arg)
+{
+	struct apml_reg_xfer_msg msg = { 0 };
+	unsigned int data_read;
+	int ret;
+
+	/* Copy the structure from user */
+	if (copy_from_user(&msg, arg, sizeof(struct apml_reg_xfer_msg)))
+		return -EFAULT;
+
+	mutex_lock(&data->lock);
+	if (msg.rflag) {
+		ret = regmap_read(data->regmap, msg.reg_addr, &data_read);
+		if (!ret)
+			msg.data_in_out = data_read;
+	} else {
+		ret = regmap_write(data->regmap, msg.reg_addr, msg.data_in_out);
+	}
+
+	mutex_unlock(&data->lock);
+
+	if (msg.rflag && !ret)
+		if (copy_to_user(arg, &msg, sizeof(struct apml_reg_xfer_msg)))
+			return -EFAULT;
+	return ret;
+}
+
+static int apml_mailbox_xfer(struct sbrmi_data *data, struct apml_mbox_msg __user *arg)
+{
+	struct apml_mbox_msg msg = { 0 };
+	int ret;
+
+	/* Copy the structure from user */
+	if (copy_from_user(&msg, arg, sizeof(struct apml_mbox_msg)))
+		return -EFAULT;
+
+	/* Mailbox protocol */
+	ret = rmi_mailbox_xfer(data, &msg);
+	if (ret && ret != -EPROTOTYPE)
+		return ret;
+
+	if (copy_to_user(arg, &msg, sizeof(struct apml_mbox_msg)))
+		return -EFAULT;
+	return ret;
+}
+
+static int apml_cpuid_xfer(struct sbrmi_data *data, struct apml_cpuid_msg __user *arg)
+{
+	struct apml_cpuid_msg msg = { 0 };
+	int ret;
+
+	/* Copy the structure from user */
+	if (copy_from_user(&msg, arg, sizeof(struct apml_cpuid_msg)))
+		return -EFAULT;
+
+	/* CPUID Protocol */
+	ret = rmi_cpuid_read(data, &msg);
+	if (ret && ret != -EPROTOTYPE)
+		return ret;
+
+	if (copy_to_user(arg, &msg, sizeof(struct apml_cpuid_msg)))
+		return -EFAULT;
+	return ret;
+}
+
+static int apml_mcamsr_xfer(struct sbrmi_data *data, struct apml_mcamsr_msg __user *arg)
+{
+	struct apml_mcamsr_msg msg = { 0 };
+	int ret;
+
+	/* Copy the structure from user */
+	if (copy_from_user(&msg, arg, sizeof(struct apml_mcamsr_msg)))
+		return -EFAULT;
+
+	/* MCAMSR Protocol */
+	ret = rmi_mca_msr_read(data, &msg);
+	if (ret && ret != -EPROTOTYPE)
+		return ret;
+
+	if (copy_to_user(arg, &msg, sizeof(struct apml_mcamsr_msg)))
+		return -EFAULT;
+	return ret;
+}
+
+static long sbrmi_ioctl(struct file *fp, unsigned int cmd, unsigned long arg)
+{
+	void __user *argp = (void __user *)arg;
+	struct sbrmi_data *data;
+
+	data = container_of(fp->private_data, struct sbrmi_data, sbrmi_misc_dev);
+	switch (cmd) {
+	case SBRMI_IOCTL_MBOX_CMD:
+		return apml_mailbox_xfer(data, argp);
+	case SBRMI_IOCTL_CPUID_CMD:
+		return apml_cpuid_xfer(data, argp);
+	case SBRMI_IOCTL_MCAMSR_CMD:
+		return apml_mcamsr_xfer(data, argp);
+	case SBRMI_IOCTL_REG_XFER_CMD:
+		return apml_rmi_reg_xfer(data, argp);
+	default:
+		return -ENOTTY;
+	}
+}
+
+static const struct file_operations sbrmi_fops = {
+	.owner		= THIS_MODULE,
+	.unlocked_ioctl	= sbrmi_ioctl,
+	.compat_ioctl	= compat_ptr_ioctl,
+};
+
+int create_misc_rmi_device(struct sbrmi_data *data,
+			   struct device *dev)
+{
+	data->sbrmi_misc_dev.name	= devm_kasprintf(dev,
+							 GFP_KERNEL,
+							 "sbrmi-%x",
+							 data->dev_static_addr);
+	data->sbrmi_misc_dev.minor	= MISC_DYNAMIC_MINOR;
+	data->sbrmi_misc_dev.fops	= &sbrmi_fops;
+	data->sbrmi_misc_dev.parent	= dev;
+	data->sbrmi_misc_dev.nodename	= devm_kasprintf(dev,
+							 GFP_KERNEL,
+							 "sbrmi-%x",
+							 data->dev_static_addr);
+	data->sbrmi_misc_dev.mode	= 0600;
+
+	return misc_register(&data->sbrmi_misc_dev);
+}

linux-7.2.3/drivers/misc/amd-sbi/rmi-core.h

@@ -0,0 +1,74 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2025 Advanced Micro Devices, Inc.
+ */
+
+#ifndef _SBRMI_CORE_H_
+#define _SBRMI_CORE_H_
+
+#include <linux/miscdevice.h>
+#include <linux/mutex.h>
+#include <linux/i2c.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <uapi/misc/amd-apml.h>
+
+/* SB-RMI registers */
+enum sbrmi_reg {
+	SBRMI_REV,
+	SBRMI_CTRL,
+	SBRMI_STATUS,
+	SBRMI_OUTBNDMSG0	= 0x30,
+	SBRMI_OUTBNDMSG1,
+	SBRMI_OUTBNDMSG2,
+	SBRMI_OUTBNDMSG3,
+	SBRMI_OUTBNDMSG4,
+	SBRMI_OUTBNDMSG5,
+	SBRMI_OUTBNDMSG6,
+	SBRMI_OUTBNDMSG7,
+	SBRMI_INBNDMSG0,
+	SBRMI_INBNDMSG1,
+	SBRMI_INBNDMSG2,
+	SBRMI_INBNDMSG3,
+	SBRMI_INBNDMSG4,
+	SBRMI_INBNDMSG5,
+	SBRMI_INBNDMSG6,
+	SBRMI_INBNDMSG7,
+	SBRMI_SW_INTERRUPT,
+	SBRMI_THREAD128CS	= 0x4b,
+};
+
+/*
+ * SB-RMI supports soft mailbox service request to MP1 (power management
+ * firmware) through SBRMI inbound/outbound message registers.
+ * SB-RMI message IDs
+ */
+enum sbrmi_msg_id {
+	SBRMI_READ_PKG_PWR_CONSUMPTION = 0x1,
+	SBRMI_WRITE_PKG_PWR_LIMIT,
+	SBRMI_READ_PKG_PWR_LIMIT,
+	SBRMI_READ_PKG_MAX_PWR_LIMIT,
+};
+
+/* Each client has this additional data */
+struct sbrmi_data {
+	struct miscdevice sbrmi_misc_dev;
+	struct regmap *regmap;
+	/* Mutex locking */
+	struct mutex lock;
+	u32 pwr_limit_max;
+	u8 dev_static_addr;
+	u8 rev;
+};
+
+int rmi_mailbox_xfer(struct sbrmi_data *data, struct apml_mbox_msg *msg);
+#ifdef CONFIG_AMD_SBRMI_HWMON
+int create_hwmon_sensor_device(struct device *dev, struct sbrmi_data *data);
+#else
+static inline int create_hwmon_sensor_device(struct device *dev, struct sbrmi_data *data)
+{
+	return 0;
+}
+#endif
+int create_misc_rmi_device(struct sbrmi_data *data, struct device *dev);
+#endif /*_SBRMI_CORE_H_*/

linux-7.2.3/drivers/misc/amd-sbi/rmi-hwmon.c

@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * rmi-hwmon.c - hwmon sensor support for side band RMI
+ *
+ * Copyright (C) 2025 Advanced Micro Devices, Inc.
+ */
+#include <linux/err.h>
+#include <linux/hwmon.h>
+#include <uapi/misc/amd-apml.h>
+#include "rmi-core.h"
+
+/* Do not allow setting negative power limit */
+#define SBRMI_PWR_MIN  0
+
+static int sbrmi_read(struct device *dev, enum hwmon_sensor_types type,
+		      u32 attr, int channel, long *val)
+{
+	struct sbrmi_data *data = dev_get_drvdata(dev);
+	struct apml_mbox_msg msg = { 0 };
+	int ret;
+
+	if (!data)
+		return -ENODEV;
+
+	if (type != hwmon_power)
+		return -EINVAL;
+
+	switch (attr) {
+	case hwmon_power_input:
+		msg.cmd = SBRMI_READ_PKG_PWR_CONSUMPTION;
+		ret = rmi_mailbox_xfer(data, &msg);
+		break;
+	case hwmon_power_cap:
+		msg.cmd = SBRMI_READ_PKG_PWR_LIMIT;
+		ret = rmi_mailbox_xfer(data, &msg);
+		break;
+	case hwmon_power_cap_max:
+		msg.mb_in_out = data->pwr_limit_max;
+		ret = 0;
+		break;
+	default:
+		return -EINVAL;
+	}
+	if (ret < 0)
+		return ret;
+	/* hwmon power attributes are in microWatt */
+	*val = (long)msg.mb_in_out * 1000;
+	return ret;
+}
+
+static int sbrmi_write(struct device *dev, enum hwmon_sensor_types type,
+		       u32 attr, int channel, long val)
+{
+	struct sbrmi_data *data = dev_get_drvdata(dev);
+	struct apml_mbox_msg msg = { 0 };
+
+	if (!data)
+		return -ENODEV;
+
+	if (type != hwmon_power && attr != hwmon_power_cap)
+		return -EINVAL;
+	/*
+	 * hwmon power attributes are in microWatt
+	 * mailbox read/write is in mWatt
+	 */
+	val /= 1000;
+
+	val = clamp_val(val, SBRMI_PWR_MIN, data->pwr_limit_max);
+
+	msg.cmd = SBRMI_WRITE_PKG_PWR_LIMIT;
+	msg.mb_in_out = val;
+
+	return rmi_mailbox_xfer(data, &msg);
+}
+
+static umode_t sbrmi_is_visible(const void *data,
+				enum hwmon_sensor_types type,
+				u32 attr, int channel)
+{
+	switch (type) {
+	case hwmon_power:
+		switch (attr) {
+		case hwmon_power_input:
+		case hwmon_power_cap_max:
+			return 0444;
+		case hwmon_power_cap:
+			return 0644;
+		}
+		break;
+	default:
+		break;
+	}
+	return 0;
+}
+
+static const struct hwmon_channel_info * const sbrmi_info[] = {
+	HWMON_CHANNEL_INFO(power,
+			   HWMON_P_INPUT | HWMON_P_CAP | HWMON_P_CAP_MAX),
+	NULL
+};
+
+static const struct hwmon_ops sbrmi_hwmon_ops = {
+	.is_visible = sbrmi_is_visible,
+	.read = sbrmi_read,
+	.write = sbrmi_write,
+};
+
+static const struct hwmon_chip_info sbrmi_chip_info = {
+	.ops = &sbrmi_hwmon_ops,
+	.info = sbrmi_info,
+};
+
+int create_hwmon_sensor_device(struct device *dev, struct sbrmi_data *data)
+{
+	struct device *hwmon_dev;
+
+	hwmon_dev = devm_hwmon_device_register_with_info(dev, "sbrmi", data,
+							 &sbrmi_chip_info, NULL);
+	return PTR_ERR_OR_ZERO(hwmon_dev);
+}

linux-7.2.3/drivers/misc/amd-sbi/rmi-i2c.c

@@ -0,0 +1,247 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * rmi-i2c.c - Side band RMI over I2C support for AMD out
+ *             of band management
+ *
+ * Copyright (C) 2024 Advanced Micro Devices, Inc.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/i3c/device.h>
+#include <linux/i3c/master.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include "rmi-core.h"
+
+#define REV_TWO_BYTE_ADDR	0x21
+
+static int sbrmi_enable_alert(struct sbrmi_data *data)
+{
+	int ctrl, ret;
+
+	/*
+	 * Enable the SB-RMI Software alert status
+	 * by writing 0 to bit 4 of Control register(0x1)
+	 */
+	ret = regmap_read(data->regmap, SBRMI_CTRL, &ctrl);
+	if (ret < 0)
+		return ret;
+
+	if (ctrl & 0x10) {
+		ctrl &= ~0x10;
+		return regmap_write(data->regmap, SBRMI_CTRL, ctrl);
+	}
+
+	return 0;
+}
+
+static int sbrmi_get_max_pwr_limit(struct sbrmi_data *data)
+{
+	struct apml_mbox_msg msg = { 0 };
+	int ret;
+
+	msg.cmd = SBRMI_READ_PKG_MAX_PWR_LIMIT;
+	ret = rmi_mailbox_xfer(data, &msg);
+	if (ret < 0)
+		return ret;
+	data->pwr_limit_max = msg.mb_in_out;
+
+	return ret;
+}
+
+static int sbrmi_common_probe(struct device *dev, struct regmap *regmap, uint8_t address)
+{
+	struct sbrmi_data *data;
+	int ret;
+
+	data = devm_kzalloc(dev, sizeof(struct sbrmi_data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->regmap = regmap;
+	mutex_init(&data->lock);
+
+	/* Enable alert for SB-RMI sequence */
+	ret = sbrmi_enable_alert(data);
+	if (ret < 0)
+		return ret;
+
+	/* Cache maximum power limit */
+	ret = sbrmi_get_max_pwr_limit(data);
+	if (ret < 0)
+		return ret;
+
+	data->dev_static_addr = address;
+
+	dev_set_drvdata(dev, data);
+
+	ret = create_hwmon_sensor_device(dev, data);
+	if (ret < 0)
+		return ret;
+	return create_misc_rmi_device(data, dev);
+}
+
+static struct regmap_config sbrmi_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+};
+
+static struct regmap_config sbrmi_regmap_config_ext = {
+	.reg_bits = 16,
+	.val_bits = 8,
+	.reg_format_endian = REGMAP_ENDIAN_LITTLE,
+};
+
+static int sbrmi_i2c_probe(struct i2c_client *client)
+{
+	struct device *dev = &client->dev;
+	struct regmap *regmap;
+	int rev, ret;
+
+	regmap = devm_regmap_init_i2c(client, &sbrmi_regmap_config);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	ret = regmap_read(regmap, SBRMI_REV, &rev);
+	if (ret)
+		return ret;
+
+	/*
+	 * For Turin and newer platforms, revision is 0x21 or later. This is
+	 * to identify the two byte register address size. However, one
+	 * byte transaction can be successful.
+	 * Verify if revision is 0x21 or later, if yes, switch to 2 byte
+	 * address size.
+	 * Continuously using 1 byte address for revision 0x21 or later can lead
+	 * to bus corruption.
+	 */
+	if (rev >= REV_TWO_BYTE_ADDR) {
+		regmap = devm_regmap_init_i2c(client, &sbrmi_regmap_config_ext);
+		if (IS_ERR(regmap))
+			return PTR_ERR(regmap);
+	}
+	return sbrmi_common_probe(dev, regmap, client->addr);
+}
+
+static void sbrmi_i2c_remove(struct i2c_client *client)
+{
+	struct sbrmi_data *data = dev_get_drvdata(&client->dev);
+
+	misc_deregister(&data->sbrmi_misc_dev);
+	/* Assign fops and parent of misc dev to NULL */
+	data->sbrmi_misc_dev.fops = NULL;
+	data->sbrmi_misc_dev.parent = NULL;
+	dev_info(&client->dev, "Removed sbrmi-i2c driver\n");
+	return;
+}
+
+static const struct i2c_device_id sbrmi_id[] = {
+	{"sbrmi-i2c"},
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, sbrmi_id);
+
+static const struct of_device_id __maybe_unused sbrmi_of_match[] = {
+	{
+		.compatible = "amd,sbrmi",
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, sbrmi_of_match);
+
+static struct i2c_driver sbrmi_driver = {
+	.driver = {
+		.name = "sbrmi-i2c",
+		.of_match_table = of_match_ptr(sbrmi_of_match),
+	},
+	.probe = sbrmi_i2c_probe,
+	.remove = sbrmi_i2c_remove,
+	.id_table = sbrmi_id,
+};
+
+static int sbrmi_i3c_probe(struct i3c_device *i3cdev)
+{
+	struct device *dev = i3cdev_to_dev(i3cdev);
+	struct regmap *regmap;
+	int rev, ret;
+
+	/*
+	 * AMD OOB devices are distinguished by their Instance ID.
+	 * For SBRMI, the Instance ID is 1. Since the device ID match
+	 * does not account for the Instance ID, the following check
+	 * ensures that only the SBRMI device is probed, excluding
+	 * other OOB devices.
+	 */
+	if (I3C_PID_INSTANCE_ID(i3cdev->desc->info.pid) != 1)
+		return -ENXIO;
+
+	regmap = devm_regmap_init_i3c(i3cdev, &sbrmi_regmap_config);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	ret = regmap_read(regmap, SBRMI_REV, &rev);
+	if (ret)
+		return ret;
+
+	/*
+	 * For Turin and newer platforms, revision is 0x21 or later. This is
+	 * to identify the two byte register address size. However, one
+	 * byte transaction can be successful.
+	 * Verify if revision is 0x21 or later, if yes, switch to 2 byte
+	 * address size.
+	 * Continuously using 1 byte address for revision 0x21 or later can lead
+	 * to bus corruption.
+	 */
+	if (rev >= REV_TWO_BYTE_ADDR) {
+		regmap = devm_regmap_init_i3c(i3cdev, &sbrmi_regmap_config_ext);
+		if (IS_ERR(regmap))
+			return PTR_ERR(regmap);
+	}
+
+	/*
+	 * AMD APML I3C devices support static address.
+	 * If static address is defined, dynamic address is same as static address.
+	 * In case static address is not defined, I3C master controller defined
+	 * dynamic address is used.
+	 */
+	return sbrmi_common_probe(dev, regmap, i3cdev->desc->info.dyn_addr);
+}
+
+static void sbrmi_i3c_remove(struct i3c_device *i3cdev)
+{
+	struct sbrmi_data *data = dev_get_drvdata(&i3cdev->dev);
+
+	misc_deregister(&data->sbrmi_misc_dev);
+}
+
+static const struct i3c_device_id sbrmi_i3c_id[] = {
+	/* PID for AMD SBRMI device */
+	I3C_DEVICE_EXTRA_INFO(0x112, 0x0, 0x2, NULL),
+	I3C_DEVICE_EXTRA_INFO(0x0, 0x0, 0x118, NULL), /* Socket:0, Venice */
+	I3C_DEVICE_EXTRA_INFO(0x0, 0x100, 0x118, NULL), /* Socket:1, Venice */
+	I3C_DEVICE_EXTRA_INFO(0x112, 0x0, 0x119, NULL), /* Socket:0, Venice */
+	I3C_DEVICE_EXTRA_INFO(0x112, 0x100, 0x119, NULL), /* Socket:1, Venice */
+	{}
+};
+MODULE_DEVICE_TABLE(i3c, sbrmi_i3c_id);
+
+static struct i3c_driver sbrmi_i3c_driver = {
+	.driver = {
+		.name = "sbrmi-i3c",
+	},
+	.probe = sbrmi_i3c_probe,
+	.remove = sbrmi_i3c_remove,
+	.id_table = sbrmi_i3c_id,
+};
+
+module_i3c_i2c_driver(sbrmi_i3c_driver, &sbrmi_driver);
+
+MODULE_AUTHOR("Akshay Gupta <akshay.gupta@amd.com>");
+MODULE_AUTHOR("Naveen Krishna Chatradhi <naveenkrishna.chatradhi@amd.com>");
+MODULE_DESCRIPTION("Hwmon driver for AMD SB-RMI emulated sensor");
+MODULE_LICENSE("GPL");