Resguardo inicial

linux-7.2.3/drivers/mtd/nand/raw/gpmi-nand/Makefile

@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_MTD_NAND_GPMI_NAND) += gpmi-nand.o

linux-7.2.3/drivers/mtd/nand/raw/gpmi-nand/bch-regs.h

@@ -0,0 +1,115 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Freescale GPMI NAND Flash Driver
+ *
+ * Copyright 2008-2011 Freescale Semiconductor, Inc.
+ * Copyright 2008 Embedded Alley Solutions, Inc.
+ */
+#ifndef __GPMI_NAND_BCH_REGS_H
+#define __GPMI_NAND_BCH_REGS_H
+
+#define HW_BCH_CTRL				0x00000000
+#define HW_BCH_CTRL_SET				0x00000004
+#define HW_BCH_CTRL_CLR				0x00000008
+#define HW_BCH_CTRL_TOG				0x0000000c
+
+#define BM_BCH_CTRL_COMPLETE_IRQ_EN		(1 << 8)
+#define BM_BCH_CTRL_COMPLETE_IRQ		(1 << 0)
+
+#define HW_BCH_STATUS0				0x00000010
+#define HW_BCH_MODE				0x00000020
+#define HW_BCH_ENCODEPTR			0x00000030
+#define HW_BCH_DATAPTR				0x00000040
+#define HW_BCH_METAPTR				0x00000050
+#define HW_BCH_LAYOUTSELECT			0x00000070
+
+#define HW_BCH_FLASH0LAYOUT0			0x00000080
+
+#define BP_BCH_FLASH0LAYOUT0_NBLOCKS		24
+#define BM_BCH_FLASH0LAYOUT0_NBLOCKS	(0xff << BP_BCH_FLASH0LAYOUT0_NBLOCKS)
+#define BF_BCH_FLASH0LAYOUT0_NBLOCKS(v)		\
+	(((v) << BP_BCH_FLASH0LAYOUT0_NBLOCKS) & BM_BCH_FLASH0LAYOUT0_NBLOCKS)
+
+#define BP_BCH_FLASH0LAYOUT0_META_SIZE		16
+#define BM_BCH_FLASH0LAYOUT0_META_SIZE	(0xff << BP_BCH_FLASH0LAYOUT0_META_SIZE)
+#define BF_BCH_FLASH0LAYOUT0_META_SIZE(v)	\
+	(((v) << BP_BCH_FLASH0LAYOUT0_META_SIZE)\
+					 & BM_BCH_FLASH0LAYOUT0_META_SIZE)
+
+#define BP_BCH_FLASH0LAYOUT0_ECC0		12
+#define BM_BCH_FLASH0LAYOUT0_ECC0	(0xf << BP_BCH_FLASH0LAYOUT0_ECC0)
+#define MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0		11
+#define MX6Q_BM_BCH_FLASH0LAYOUT0_ECC0	(0x1f << MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0)
+#define BF_BCH_FLASH0LAYOUT0_ECC0(v, x)				\
+	(GPMI_IS_MX6(x)					\
+		? (((v) << MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0)	\
+			& MX6Q_BM_BCH_FLASH0LAYOUT0_ECC0)	\
+		: (((v) << BP_BCH_FLASH0LAYOUT0_ECC0)		\
+			& BM_BCH_FLASH0LAYOUT0_ECC0)		\
+	)
+
+#define MX6Q_BP_BCH_FLASH0LAYOUT0_GF_13_14	10
+#define MX6Q_BM_BCH_FLASH0LAYOUT0_GF_13_14			\
+				(0x1 << MX6Q_BP_BCH_FLASH0LAYOUT0_GF_13_14)
+#define BF_BCH_FLASH0LAYOUT0_GF(v, x)				\
+	((GPMI_IS_MX6(x) && ((v) == 14))			\
+		? (((1) << MX6Q_BP_BCH_FLASH0LAYOUT0_GF_13_14)	\
+			& MX6Q_BM_BCH_FLASH0LAYOUT0_GF_13_14)	\
+		: 0						\
+	)
+
+#define BP_BCH_FLASH0LAYOUT0_DATA0_SIZE		0
+#define BM_BCH_FLASH0LAYOUT0_DATA0_SIZE		\
+			(0xfff << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE)
+#define MX6Q_BM_BCH_FLASH0LAYOUT0_DATA0_SIZE	\
+			(0x3ff << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE)
+#define BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(v, x)				\
+	(GPMI_IS_MX6(x)						\
+		? (((v) >> 2) & MX6Q_BM_BCH_FLASH0LAYOUT0_DATA0_SIZE)	\
+		: ((v) & BM_BCH_FLASH0LAYOUT0_DATA0_SIZE)		\
+	)
+
+#define HW_BCH_FLASH0LAYOUT1			0x00000090
+
+#define BP_BCH_FLASH0LAYOUT1_PAGE_SIZE		16
+#define BM_BCH_FLASH0LAYOUT1_PAGE_SIZE		\
+			(0xffff << BP_BCH_FLASH0LAYOUT1_PAGE_SIZE)
+#define BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(v)	\
+	(((v) << BP_BCH_FLASH0LAYOUT1_PAGE_SIZE) \
+					 & BM_BCH_FLASH0LAYOUT1_PAGE_SIZE)
+
+#define BP_BCH_FLASH0LAYOUT1_ECCN		12
+#define BM_BCH_FLASH0LAYOUT1_ECCN	(0xf << BP_BCH_FLASH0LAYOUT1_ECCN)
+#define MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN		11
+#define MX6Q_BM_BCH_FLASH0LAYOUT1_ECCN	(0x1f << MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN)
+#define BF_BCH_FLASH0LAYOUT1_ECCN(v, x)				\
+	(GPMI_IS_MX6(x)					\
+		? (((v) << MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN)	\
+			& MX6Q_BM_BCH_FLASH0LAYOUT1_ECCN)	\
+		: (((v) << BP_BCH_FLASH0LAYOUT1_ECCN)		\
+			& BM_BCH_FLASH0LAYOUT1_ECCN)		\
+	)
+
+#define MX6Q_BP_BCH_FLASH0LAYOUT1_GF_13_14	10
+#define MX6Q_BM_BCH_FLASH0LAYOUT1_GF_13_14			\
+				(0x1 << MX6Q_BP_BCH_FLASH0LAYOUT1_GF_13_14)
+#define BF_BCH_FLASH0LAYOUT1_GF(v, x)				\
+	((GPMI_IS_MX6(x) && ((v) == 14))			\
+		? (((1) << MX6Q_BP_BCH_FLASH0LAYOUT1_GF_13_14)	\
+			& MX6Q_BM_BCH_FLASH0LAYOUT1_GF_13_14)	\
+		: 0						\
+	)
+
+#define BP_BCH_FLASH0LAYOUT1_DATAN_SIZE		0
+#define BM_BCH_FLASH0LAYOUT1_DATAN_SIZE		\
+			(0xfff << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE)
+#define MX6Q_BM_BCH_FLASH0LAYOUT1_DATAN_SIZE	\
+			(0x3ff << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE)
+#define BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(v, x)				\
+	(GPMI_IS_MX6(x)						\
+		? (((v) >> 2) & MX6Q_BM_BCH_FLASH0LAYOUT1_DATAN_SIZE)	\
+		: ((v) & BM_BCH_FLASH0LAYOUT1_DATAN_SIZE)		\
+	)
+
+#define HW_BCH_VERSION				0x00000160
+#endif

linux-7.2.3/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h

@@ -0,0 +1,183 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Freescale GPMI NAND Flash Driver
+ *
+ * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
+ * Copyright (C) 2008 Embedded Alley Solutions, Inc.
+ */
+#ifndef __DRIVERS_MTD_NAND_GPMI_NAND_H
+#define __DRIVERS_MTD_NAND_GPMI_NAND_H
+
+#include <linux/mtd/rawnand.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+
+#define GPMI_CLK_MAX 5 /* MX6Q needs five clocks */
+struct resources {
+	void __iomem  *gpmi_regs;
+	void __iomem  *bch_regs;
+	unsigned int  dma_low_channel;
+	unsigned int  dma_high_channel;
+	struct clk    *clock[GPMI_CLK_MAX];
+};
+
+/**
+ * struct bch_geometry - BCH geometry description.
+ * @gf_len:                   The length of Galois Field. (e.g., 13 or 14)
+ * @ecc_strength:             A number that describes the strength of the ECC
+ *                            algorithm.
+ * @page_size:                The size, in bytes, of a physical page, including
+ *                            both data and OOB.
+ * @metadata_size:            The size, in bytes, of the metadata.
+ * @ecc0_chunk_size:          The size, in bytes, of a first ECC chunk.
+ * @eccn_chunk_size:          The size, in bytes, of a single ECC chunk after
+ *                            the first chunk in the page.
+ * @ecc_chunk_count:          The number of ECC chunks in the page,
+ * @payload_size:             The size, in bytes, of the payload buffer.
+ * @auxiliary_size:           The size, in bytes, of the auxiliary buffer.
+ * @auxiliary_status_offset:  The offset into the auxiliary buffer at which
+ *                            the ECC status appears.
+ * @block_mark_byte_offset:   The byte offset in the ECC-based page view at
+ *                            which the underlying physical block mark appears.
+ * @block_mark_bit_offset:    The bit offset into the ECC-based page view at
+ *                            which the underlying physical block mark appears.
+ * @ecc_for_meta:             The flag to indicate if there is a dedicate ecc
+ *                            for meta.
+ */
+struct bch_geometry {
+	unsigned int  gf_len;
+	unsigned int  ecc_strength;
+	unsigned int  page_size;
+	unsigned int  metadata_size;
+	unsigned int  ecc0_chunk_size;
+	unsigned int  eccn_chunk_size;
+	unsigned int  ecc_chunk_count;
+	unsigned int  payload_size;
+	unsigned int  auxiliary_size;
+	unsigned int  auxiliary_status_offset;
+	unsigned int  block_mark_byte_offset;
+	unsigned int  block_mark_bit_offset;
+	unsigned int  ecc_for_meta; /* ECC for meta data */
+};
+
+/**
+ * struct boot_rom_geometry - Boot ROM geometry description.
+ * @stride_size_in_pages:        The size of a boot block stride, in pages.
+ * @search_area_stride_exponent: The logarithm to base 2 of the size of a
+ *                               search area in boot block strides.
+ */
+struct boot_rom_geometry {
+	unsigned int  stride_size_in_pages;
+	unsigned int  search_area_stride_exponent;
+};
+
+enum gpmi_type {
+	IS_MX23,
+	IS_MX28,
+	IS_MX6Q,
+	IS_MX6SX,
+	IS_MX7D,
+	IS_MX8QXP,
+};
+
+struct gpmi_devdata {
+	enum gpmi_type type;
+	int bch_max_ecc_strength;
+	int max_chain_delay; /* See the SDR EDO mode */
+	const char * const *clks;
+	const int clks_count;
+	bool support_edo_timing;
+};
+
+/**
+ * struct gpmi_nfc_hardware_timing - GPMI hardware timing parameters.
+ * @must_apply_timings:        Whether controller timings have already been
+ *                             applied or not (useful only while there is
+ *                             support for only one chip select)
+ * @clk_rate:                  The clock rate that must be used to derive the
+ *                             following parameters
+ * @timing0:                   HW_GPMI_TIMING0 register
+ * @timing1:                   HW_GPMI_TIMING1 register
+ * @ctrl1n:                    HW_GPMI_CTRL1n register
+ */
+struct gpmi_nfc_hardware_timing {
+	bool must_apply_timings;
+	unsigned long int clk_rate;
+	u32 timing0;
+	u32 timing1;
+	u32 ctrl1n;
+};
+
+#define GPMI_MAX_TRANSFERS	8
+
+struct gpmi_transfer {
+	u8 cmdbuf[8];
+	struct scatterlist sgl;
+	enum dma_data_direction direction;
+};
+
+struct gpmi_nand_data {
+	/* Devdata */
+	const struct gpmi_devdata *devdata;
+
+	/* System Interface */
+	struct device		*dev;
+	struct platform_device	*pdev;
+
+	/* Resources */
+	struct resources	resources;
+
+	/* Flash Hardware */
+	struct gpmi_nfc_hardware_timing hw;
+
+	/* BCH */
+	struct bch_geometry	bch_geometry;
+	struct completion	bch_done;
+
+	/* NAND Boot issue */
+	bool			swap_block_mark;
+	struct boot_rom_geometry rom_geometry;
+
+	/* MTD / NAND */
+	struct nand_controller	base;
+	struct nand_chip	nand;
+
+	struct gpmi_transfer	transfers[GPMI_MAX_TRANSFERS];
+	int			ntransfers;
+
+	bool			bch;
+	uint32_t		bch_flashlayout0;
+	uint32_t		bch_flashlayout1;
+
+	char			*data_buffer_dma;
+
+	void			*auxiliary_virt;
+	dma_addr_t		auxiliary_phys;
+
+	void			*raw_buffer;
+
+	/* DMA channels */
+#define DMA_CHANS		8
+	struct dma_chan		*dma_chans[DMA_CHANS];
+	struct completion	dma_done;
+};
+
+/* BCH : Status Block Completion Codes */
+#define STATUS_GOOD		0x00
+#define STATUS_ERASED		0xff
+#define STATUS_UNCORRECTABLE	0xfe
+
+/* Use the devdata to distinguish different Archs. */
+#define GPMI_IS_MX23(x)		((x)->devdata->type == IS_MX23)
+#define GPMI_IS_MX28(x)		((x)->devdata->type == IS_MX28)
+#define GPMI_IS_MX6Q(x)		((x)->devdata->type == IS_MX6Q)
+#define GPMI_IS_MX6SX(x)	((x)->devdata->type == IS_MX6SX)
+#define GPMI_IS_MX7D(x)		((x)->devdata->type == IS_MX7D)
+#define GPMI_IS_MX8QXP(x)	((x)->devdata->type == IS_MX8QXP)
+
+#define GPMI_IS_MX6(x)		(GPMI_IS_MX6Q(x) || GPMI_IS_MX6SX(x) || \
+				 GPMI_IS_MX7D(x) || GPMI_IS_MX8QXP(x))
+
+#define GPMI_IS_MXS(x)		(GPMI_IS_MX23(x) || GPMI_IS_MX28(x))
+#endif

linux-7.2.3/drivers/mtd/nand/raw/gpmi-nand/gpmi-regs.h

@@ -0,0 +1,180 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Freescale GPMI NAND Flash Driver
+ *
+ * Copyright 2008-2011 Freescale Semiconductor, Inc.
+ * Copyright 2008 Embedded Alley Solutions, Inc.
+ */
+#ifndef __GPMI_NAND_GPMI_REGS_H
+#define __GPMI_NAND_GPMI_REGS_H
+
+#define HW_GPMI_CTRL0					0x00000000
+#define HW_GPMI_CTRL0_SET				0x00000004
+#define HW_GPMI_CTRL0_CLR				0x00000008
+#define HW_GPMI_CTRL0_TOG				0x0000000c
+
+#define BP_GPMI_CTRL0_COMMAND_MODE			24
+#define BM_GPMI_CTRL0_COMMAND_MODE	(3 << BP_GPMI_CTRL0_COMMAND_MODE)
+#define BF_GPMI_CTRL0_COMMAND_MODE(v)	\
+	(((v) << BP_GPMI_CTRL0_COMMAND_MODE) & BM_GPMI_CTRL0_COMMAND_MODE)
+#define BV_GPMI_CTRL0_COMMAND_MODE__WRITE		0x0
+#define BV_GPMI_CTRL0_COMMAND_MODE__READ		0x1
+#define BV_GPMI_CTRL0_COMMAND_MODE__READ_AND_COMPARE	0x2
+#define BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY	0x3
+
+#define BM_GPMI_CTRL0_WORD_LENGTH			(1 << 23)
+#define BV_GPMI_CTRL0_WORD_LENGTH__16_BIT		0x0
+#define BV_GPMI_CTRL0_WORD_LENGTH__8_BIT		0x1
+
+/*
+ *  Difference in LOCK_CS between imx23 and imx28 :
+ *  This bit may impact the _POWER_ consumption. So some chips
+ *  do not set it.
+ */
+#define MX23_BP_GPMI_CTRL0_LOCK_CS			22
+#define MX28_BP_GPMI_CTRL0_LOCK_CS			27
+#define LOCK_CS_ENABLE					0x1
+#define BF_GPMI_CTRL0_LOCK_CS(v, x)			0x0
+
+/* Difference in CS between imx23 and imx28 */
+#define BP_GPMI_CTRL0_CS				20
+#define MX23_BM_GPMI_CTRL0_CS		(3 << BP_GPMI_CTRL0_CS)
+#define MX28_BM_GPMI_CTRL0_CS		(7 << BP_GPMI_CTRL0_CS)
+#define BF_GPMI_CTRL0_CS(v, x)		(((v) << BP_GPMI_CTRL0_CS) & \
+						(GPMI_IS_MX23((x)) \
+						? MX23_BM_GPMI_CTRL0_CS	\
+						: MX28_BM_GPMI_CTRL0_CS))
+
+#define BP_GPMI_CTRL0_ADDRESS				17
+#define BM_GPMI_CTRL0_ADDRESS		(3 << BP_GPMI_CTRL0_ADDRESS)
+#define BF_GPMI_CTRL0_ADDRESS(v)	\
+		(((v) << BP_GPMI_CTRL0_ADDRESS) & BM_GPMI_CTRL0_ADDRESS)
+#define BV_GPMI_CTRL0_ADDRESS__NAND_DATA		0x0
+#define BV_GPMI_CTRL0_ADDRESS__NAND_CLE			0x1
+#define BV_GPMI_CTRL0_ADDRESS__NAND_ALE			0x2
+
+#define BM_GPMI_CTRL0_ADDRESS_INCREMENT			(1 << 16)
+#define BV_GPMI_CTRL0_ADDRESS_INCREMENT__DISABLED	0x0
+#define BV_GPMI_CTRL0_ADDRESS_INCREMENT__ENABLED	0x1
+
+#define BP_GPMI_CTRL0_XFER_COUNT			0
+#define BM_GPMI_CTRL0_XFER_COUNT	(0xffff << BP_GPMI_CTRL0_XFER_COUNT)
+#define BF_GPMI_CTRL0_XFER_COUNT(v)	\
+		(((v) << BP_GPMI_CTRL0_XFER_COUNT) & BM_GPMI_CTRL0_XFER_COUNT)
+
+#define HW_GPMI_COMPARE					0x00000010
+
+#define HW_GPMI_ECCCTRL					0x00000020
+#define HW_GPMI_ECCCTRL_SET				0x00000024
+#define HW_GPMI_ECCCTRL_CLR				0x00000028
+#define HW_GPMI_ECCCTRL_TOG				0x0000002c
+
+#define BP_GPMI_ECCCTRL_ECC_CMD				13
+#define BM_GPMI_ECCCTRL_ECC_CMD		(3 << BP_GPMI_ECCCTRL_ECC_CMD)
+#define BF_GPMI_ECCCTRL_ECC_CMD(v)	\
+		(((v) << BP_GPMI_ECCCTRL_ECC_CMD) & BM_GPMI_ECCCTRL_ECC_CMD)
+#define BV_GPMI_ECCCTRL_ECC_CMD__BCH_DECODE		0x0
+#define BV_GPMI_ECCCTRL_ECC_CMD__BCH_ENCODE		0x1
+
+#define BM_GPMI_ECCCTRL_ENABLE_ECC			(1 << 12)
+#define BV_GPMI_ECCCTRL_ENABLE_ECC__ENABLE		0x1
+#define BV_GPMI_ECCCTRL_ENABLE_ECC__DISABLE		0x0
+
+#define BP_GPMI_ECCCTRL_BUFFER_MASK			0
+#define BM_GPMI_ECCCTRL_BUFFER_MASK	(0x1ff << BP_GPMI_ECCCTRL_BUFFER_MASK)
+#define BF_GPMI_ECCCTRL_BUFFER_MASK(v)	\
+	(((v) << BP_GPMI_ECCCTRL_BUFFER_MASK) & BM_GPMI_ECCCTRL_BUFFER_MASK)
+#define BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY	0x100
+#define BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE		0x1FF
+
+#define HW_GPMI_ECCCOUNT				0x00000030
+#define HW_GPMI_PAYLOAD					0x00000040
+#define HW_GPMI_AUXILIARY				0x00000050
+#define HW_GPMI_CTRL1					0x00000060
+#define HW_GPMI_CTRL1_SET				0x00000064
+#define HW_GPMI_CTRL1_CLR				0x00000068
+#define HW_GPMI_CTRL1_TOG				0x0000006c
+
+#define BP_GPMI_CTRL1_DECOUPLE_CS			24
+#define BM_GPMI_CTRL1_DECOUPLE_CS	(1 << BP_GPMI_CTRL1_DECOUPLE_CS)
+
+#define BP_GPMI_CTRL1_WRN_DLY_SEL			22
+#define BM_GPMI_CTRL1_WRN_DLY_SEL	(0x3 << BP_GPMI_CTRL1_WRN_DLY_SEL)
+#define BF_GPMI_CTRL1_WRN_DLY_SEL(v)  \
+	(((v) << BP_GPMI_CTRL1_WRN_DLY_SEL) & BM_GPMI_CTRL1_WRN_DLY_SEL)
+#define BV_GPMI_CTRL1_WRN_DLY_SEL_4_TO_8NS		0x0
+#define BV_GPMI_CTRL1_WRN_DLY_SEL_6_TO_10NS		0x1
+#define BV_GPMI_CTRL1_WRN_DLY_SEL_7_TO_12NS		0x2
+#define BV_GPMI_CTRL1_WRN_DLY_SEL_NO_DELAY		0x3
+
+#define BM_GPMI_CTRL1_GANGED_RDYBUSY			(1 << 19)
+#define BM_GPMI_CTRL1_BCH_MODE				(1 << 18)
+
+#define BP_GPMI_CTRL1_DLL_ENABLE			17
+#define BM_GPMI_CTRL1_DLL_ENABLE	(1 << BP_GPMI_CTRL1_DLL_ENABLE)
+
+#define BP_GPMI_CTRL1_HALF_PERIOD			16
+#define BM_GPMI_CTRL1_HALF_PERIOD	(1 << BP_GPMI_CTRL1_HALF_PERIOD)
+
+#define BP_GPMI_CTRL1_RDN_DELAY				12
+#define BM_GPMI_CTRL1_RDN_DELAY		(0xf << BP_GPMI_CTRL1_RDN_DELAY)
+#define BF_GPMI_CTRL1_RDN_DELAY(v)	\
+		(((v) << BP_GPMI_CTRL1_RDN_DELAY) & BM_GPMI_CTRL1_RDN_DELAY)
+
+#define BM_GPMI_CTRL1_DEV_RESET				(1 << 3)
+#define BV_GPMI_CTRL1_DEV_RESET__ENABLED		0x0
+#define BV_GPMI_CTRL1_DEV_RESET__DISABLED		0x1
+
+#define BM_GPMI_CTRL1_ATA_IRQRDY_POLARITY		(1 << 2)
+#define BV_GPMI_CTRL1_ATA_IRQRDY_POLARITY__ACTIVELOW	0x0
+#define BV_GPMI_CTRL1_ATA_IRQRDY_POLARITY__ACTIVEHIGH	0x1
+
+#define BM_GPMI_CTRL1_CAMERA_MODE			(1 << 1)
+#define BV_GPMI_CTRL1_GPMI_MODE__NAND			0x0
+#define BV_GPMI_CTRL1_GPMI_MODE__ATA			0x1
+
+#define BM_GPMI_CTRL1_GPMI_MODE				(1 << 0)
+
+#define BM_GPMI_CTRL1_CLEAR_MASK (BM_GPMI_CTRL1_WRN_DLY_SEL | \
+				  BM_GPMI_CTRL1_DLL_ENABLE |  \
+				  BM_GPMI_CTRL1_RDN_DELAY |   \
+				  BM_GPMI_CTRL1_HALF_PERIOD)
+
+#define HW_GPMI_TIMING0					0x00000070
+
+#define BP_GPMI_TIMING0_ADDRESS_SETUP			16
+#define BM_GPMI_TIMING0_ADDRESS_SETUP	(0xff << BP_GPMI_TIMING0_ADDRESS_SETUP)
+#define BF_GPMI_TIMING0_ADDRESS_SETUP(v)	\
+	(((v) << BP_GPMI_TIMING0_ADDRESS_SETUP) & BM_GPMI_TIMING0_ADDRESS_SETUP)
+
+#define BP_GPMI_TIMING0_DATA_HOLD			8
+#define BM_GPMI_TIMING0_DATA_HOLD	(0xff << BP_GPMI_TIMING0_DATA_HOLD)
+#define BF_GPMI_TIMING0_DATA_HOLD(v)		\
+	(((v) << BP_GPMI_TIMING0_DATA_HOLD) & BM_GPMI_TIMING0_DATA_HOLD)
+
+#define BP_GPMI_TIMING0_DATA_SETUP			0
+#define BM_GPMI_TIMING0_DATA_SETUP	(0xff << BP_GPMI_TIMING0_DATA_SETUP)
+#define BF_GPMI_TIMING0_DATA_SETUP(v)		\
+	(((v) << BP_GPMI_TIMING0_DATA_SETUP) & BM_GPMI_TIMING0_DATA_SETUP)
+
+#define HW_GPMI_TIMING1					0x00000080
+#define BP_GPMI_TIMING1_BUSY_TIMEOUT			16
+#define BM_GPMI_TIMING1_BUSY_TIMEOUT	(0xffff << BP_GPMI_TIMING1_BUSY_TIMEOUT)
+#define BF_GPMI_TIMING1_BUSY_TIMEOUT(v)		\
+	(((v) << BP_GPMI_TIMING1_BUSY_TIMEOUT) & BM_GPMI_TIMING1_BUSY_TIMEOUT)
+
+#define HW_GPMI_TIMING2					0x00000090
+#define HW_GPMI_DATA					0x000000a0
+
+/* MX28 uses this to detect READY. */
+#define HW_GPMI_STAT					0x000000b0
+#define MX28_BP_GPMI_STAT_READY_BUSY			24
+#define MX28_BM_GPMI_STAT_READY_BUSY	(0xff << MX28_BP_GPMI_STAT_READY_BUSY)
+#define MX28_BF_GPMI_STAT_READY_BUSY(v)		\
+	(((v) << MX28_BP_GPMI_STAT_READY_BUSY) & MX28_BM_GPMI_STAT_READY_BUSY)
+
+/* MX23 uses this to detect READY. */
+#define HW_GPMI_DEBUG					0x000000c0
+#define MX23_BP_GPMI_DEBUG_READY0			28
+#define MX23_BM_GPMI_DEBUG_READY0	(1 << MX23_BP_GPMI_DEBUG_READY0)
+#endif