Resguardo inicial

linux-7.2.3/drivers/net/phy/qcom/Kconfig

@@ -0,0 +1,31 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config QCOM_NET_PHYLIB
+	tristate
+
+config AT803X_PHY
+	tristate "Qualcomm Atheros AR803X PHYs"
+	select QCOM_NET_PHYLIB
+	depends on REGULATOR
+	help
+	  Currently supports the AR8030, AR8031, AR8033, AR8035, IPQ5018 model
+
+config QCA83XX_PHY
+	tristate "Qualcomm Atheros QCA833x PHYs"
+	select QCOM_NET_PHYLIB
+	help
+	  Currently supports the internal QCA8337(Internal qca8k PHY) model
+
+config QCA808X_PHY
+	tristate "Qualcomm QCA808x PHYs"
+	select QCOM_NET_PHYLIB
+	help
+	  Currently supports the QCA8081 model
+
+config QCA807X_PHY
+	tristate "Qualcomm QCA807x PHYs"
+	select QCOM_NET_PHYLIB
+	select PHY_PACKAGE
+	depends on OF_MDIO
+	help
+	  Currently supports the Qualcomm QCA8072, QCA8075 and the PSGMII
+	  control PHY.

linux-7.2.3/drivers/net/phy/qcom/Makefile

@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_QCOM_NET_PHYLIB)	+= qcom-phy-lib.o
+obj-$(CONFIG_AT803X_PHY)	+= at803x.o
+obj-$(CONFIG_QCA83XX_PHY)	+= qca83xx.o
+obj-$(CONFIG_QCA808X_PHY)	+= qca808x.o
+obj-$(CONFIG_QCA807X_PHY)	+= qca807x.o

linux-7.2.3/drivers/net/phy/qcom/qca807x.c

@@ -0,0 +1,856 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2023 Sartura Ltd.
+ *
+ * Author: Robert Marko <robert.marko@sartura.hr>
+ *         Christian Marangi <ansuelsmth@gmail.com>
+ *
+ * Qualcomm QCA8072 and QCA8075 PHY driver
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy.h>
+#include <linux/bitfield.h>
+#include <linux/gpio/driver.h>
+#include <linux/phy_port.h>
+
+#include "../phylib.h"
+#include "qcom.h"
+
+#define QCA807X_CHIP_CONFIGURATION				0x1f
+#define QCA807X_BT_BX_REG_SEL					BIT(15)
+#define QCA807X_BT_BX_REG_SEL_FIBER				0
+#define QCA807X_BT_BX_REG_SEL_COPPER				1
+#define QCA807X_CHIP_CONFIGURATION_MODE_CFG_MASK		GENMASK(3, 0)
+#define QCA807X_CHIP_CONFIGURATION_MODE_QSGMII_SGMII		4
+#define QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_FIBER		3
+#define QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_ALL_COPPER	0
+
+#define QCA807X_MEDIA_SELECT_STATUS				0x1a
+#define QCA807X_MEDIA_DETECTED_COPPER				BIT(5)
+#define QCA807X_MEDIA_DETECTED_1000_BASE_X			BIT(4)
+#define QCA807X_MEDIA_DETECTED_100_BASE_FX			BIT(3)
+
+#define QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION			0x807e
+#define QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION_EN		BIT(0)
+
+#define QCA807X_MMD7_1000BASE_T_POWER_SAVE_PER_CABLE_LENGTH	0x801a
+#define QCA807X_CONTROL_DAC_MASK				GENMASK(2, 0)
+/* List of tweaks enabled by this bit:
+ * - With both FULL amplitude and FULL bias current: bias current
+ *   is set to half.
+ * - With only DSP amplitude: bias current is set to half and
+ *   is set to 1/4 with cable < 10m.
+ * - With DSP bias current (included both DSP amplitude and
+ *   DSP bias current): bias current is half the detected current
+ *   with cable < 10m.
+ */
+#define QCA807X_CONTROL_DAC_BIAS_CURRENT_TWEAK			BIT(2)
+#define QCA807X_CONTROL_DAC_DSP_BIAS_CURRENT			BIT(1)
+#define QCA807X_CONTROL_DAC_DSP_AMPLITUDE			BIT(0)
+
+#define QCA807X_MMD7_LED_100N_1				0x8074
+#define QCA807X_MMD7_LED_100N_2				0x8075
+#define QCA807X_MMD7_LED_1000N_1			0x8076
+#define QCA807X_MMD7_LED_1000N_2			0x8077
+
+#define QCA807X_MMD7_LED_CTRL(x)			(0x8074 + ((x) * 2))
+#define QCA807X_MMD7_LED_FORCE_CTRL(x)			(0x8075 + ((x) * 2))
+
+/* LED hw control pattern for fiber port */
+#define QCA807X_LED_FIBER_PATTERN_MASK			GENMASK(11, 1)
+#define QCA807X_LED_FIBER_TXACT_BLK_EN			BIT(10)
+#define QCA807X_LED_FIBER_RXACT_BLK_EN			BIT(9)
+#define QCA807X_LED_FIBER_FDX_ON_EN			BIT(6)
+#define QCA807X_LED_FIBER_HDX_ON_EN			BIT(5)
+#define QCA807X_LED_FIBER_1000BX_ON_EN			BIT(2)
+#define QCA807X_LED_FIBER_100FX_ON_EN			BIT(1)
+
+/* Some device repurpose the LED as GPIO out */
+#define QCA807X_GPIO_FORCE_EN				QCA808X_LED_FORCE_EN
+#define QCA807X_GPIO_FORCE_MODE_MASK			QCA808X_LED_FORCE_MODE_MASK
+
+#define QCA807X_FUNCTION_CONTROL			0x10
+#define QCA807X_FC_MDI_CROSSOVER_MODE_MASK		GENMASK(6, 5)
+#define QCA807X_FC_MDI_CROSSOVER_AUTO			3
+#define QCA807X_FC_MDI_CROSSOVER_MANUAL_MDIX		1
+#define QCA807X_FC_MDI_CROSSOVER_MANUAL_MDI		0
+
+/* PQSGMII Analog PHY specific */
+#define PQSGMII_CTRL_REG				0x0
+#define PQSGMII_ANALOG_SW_RESET				BIT(6)
+#define PQSGMII_DRIVE_CONTROL_1				0xb
+#define PQSGMII_TX_DRIVER_MASK				GENMASK(7, 4)
+#define PQSGMII_TX_DRIVER_140MV				0x0
+#define PQSGMII_TX_DRIVER_160MV				0x1
+#define PQSGMII_TX_DRIVER_180MV				0x2
+#define PQSGMII_TX_DRIVER_200MV				0x3
+#define PQSGMII_TX_DRIVER_220MV				0x4
+#define PQSGMII_TX_DRIVER_240MV				0x5
+#define PQSGMII_TX_DRIVER_260MV				0x6
+#define PQSGMII_TX_DRIVER_280MV				0x7
+#define PQSGMII_TX_DRIVER_300MV				0x8
+#define PQSGMII_TX_DRIVER_320MV				0x9
+#define PQSGMII_TX_DRIVER_400MV				0xa
+#define PQSGMII_TX_DRIVER_500MV				0xb
+#define PQSGMII_TX_DRIVER_600MV				0xc
+#define PQSGMII_MODE_CTRL				0x6d
+#define PQSGMII_MODE_CTRL_AZ_WORKAROUND_MASK		BIT(0)
+#define PQSGMII_MMD3_SERDES_CONTROL			0x805a
+
+#define PHY_ID_QCA8072		0x004dd0b2
+#define PHY_ID_QCA8075		0x004dd0b1
+
+#define QCA807X_COMBO_ADDR_OFFSET			4
+#define QCA807X_PQSGMII_ADDR_OFFSET			5
+#define SERDES_RESET_SLEEP				100
+
+enum qca807x_global_phy {
+	QCA807X_COMBO_ADDR = 4,
+	QCA807X_PQSGMII_ADDR = 5,
+};
+
+struct qca807x_shared_priv {
+	unsigned int package_mode;
+	u32 tx_drive_strength;
+};
+
+struct qca807x_gpio_priv {
+	struct phy_device *phy;
+};
+
+struct qca807x_priv {
+	bool dac_full_amplitude;
+	bool dac_full_bias_current;
+	bool dac_disable_bias_current_tweak;
+	struct qcom_phy_hw_stats hw_stats;
+};
+
+static int qca807x_cable_test_start(struct phy_device *phydev)
+{
+	/* we do all the (time consuming) work later */
+	return 0;
+}
+
+static int qca807x_led_parse_netdev(struct phy_device *phydev, unsigned long rules,
+				    u16 *offload_trigger)
+{
+	/* Parsing specific to netdev trigger */
+	switch (phydev->port) {
+	case PORT_TP:
+		if (test_bit(TRIGGER_NETDEV_TX, &rules))
+			*offload_trigger |= QCA808X_LED_TX_BLINK;
+		if (test_bit(TRIGGER_NETDEV_RX, &rules))
+			*offload_trigger |= QCA808X_LED_RX_BLINK;
+		if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
+			*offload_trigger |= QCA808X_LED_SPEED10_ON;
+		if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
+			*offload_trigger |= QCA808X_LED_SPEED100_ON;
+		if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
+			*offload_trigger |= QCA808X_LED_SPEED1000_ON;
+		if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules))
+			*offload_trigger |= QCA808X_LED_HALF_DUPLEX_ON;
+		if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules))
+			*offload_trigger |= QCA808X_LED_FULL_DUPLEX_ON;
+		break;
+	case PORT_FIBRE:
+		if (test_bit(TRIGGER_NETDEV_TX, &rules))
+			*offload_trigger |= QCA807X_LED_FIBER_TXACT_BLK_EN;
+		if (test_bit(TRIGGER_NETDEV_RX, &rules))
+			*offload_trigger |= QCA807X_LED_FIBER_RXACT_BLK_EN;
+		if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
+			*offload_trigger |= QCA807X_LED_FIBER_100FX_ON_EN;
+		if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
+			*offload_trigger |= QCA807X_LED_FIBER_1000BX_ON_EN;
+		if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules))
+			*offload_trigger |= QCA807X_LED_FIBER_HDX_ON_EN;
+		if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules))
+			*offload_trigger |= QCA807X_LED_FIBER_FDX_ON_EN;
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	if (rules && !*offload_trigger)
+		return -EOPNOTSUPP;
+
+	return 0;
+}
+
+static int qca807x_led_hw_control_enable(struct phy_device *phydev, u8 index)
+{
+	u16 reg;
+
+	if (index > 1)
+		return -EINVAL;
+
+	reg = QCA807X_MMD7_LED_FORCE_CTRL(index);
+	return qca808x_led_reg_hw_control_enable(phydev, reg);
+}
+
+static int qca807x_led_hw_is_supported(struct phy_device *phydev, u8 index,
+				       unsigned long rules)
+{
+	u16 offload_trigger = 0;
+
+	if (index > 1)
+		return -EINVAL;
+
+	return qca807x_led_parse_netdev(phydev, rules, &offload_trigger);
+}
+
+static int qca807x_led_hw_control_set(struct phy_device *phydev, u8 index,
+				      unsigned long rules)
+{
+	u16 reg, mask, offload_trigger = 0;
+	int ret;
+
+	if (index > 1)
+		return -EINVAL;
+
+	ret = qca807x_led_parse_netdev(phydev, rules, &offload_trigger);
+	if (ret)
+		return ret;
+
+	ret = qca807x_led_hw_control_enable(phydev, index);
+	if (ret)
+		return ret;
+
+	switch (phydev->port) {
+	case PORT_TP:
+		reg = QCA807X_MMD7_LED_CTRL(index);
+		mask = QCA808X_LED_PATTERN_MASK;
+		break;
+	case PORT_FIBRE:
+		/* HW control pattern bits are in LED FORCE reg */
+		reg = QCA807X_MMD7_LED_FORCE_CTRL(index);
+		mask = QCA807X_LED_FIBER_PATTERN_MASK;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return phy_modify_mmd(phydev, MDIO_MMD_AN, reg, mask,
+			      offload_trigger);
+}
+
+static bool qca807x_led_hw_control_status(struct phy_device *phydev, u8 index)
+{
+	u16 reg;
+
+	if (index > 1)
+		return false;
+
+	reg = QCA807X_MMD7_LED_FORCE_CTRL(index);
+	return qca808x_led_reg_hw_control_status(phydev, reg);
+}
+
+static int qca807x_led_hw_control_get(struct phy_device *phydev, u8 index,
+				      unsigned long *rules)
+{
+	u16 reg;
+	int val;
+
+	if (index > 1)
+		return -EINVAL;
+
+	/* Check if we have hw control enabled */
+	if (qca807x_led_hw_control_status(phydev, index))
+		return -EINVAL;
+
+	/* Parsing specific to netdev trigger */
+	switch (phydev->port) {
+	case PORT_TP:
+		reg = QCA807X_MMD7_LED_CTRL(index);
+		val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
+		if (val & QCA808X_LED_TX_BLINK)
+			set_bit(TRIGGER_NETDEV_TX, rules);
+		if (val & QCA808X_LED_RX_BLINK)
+			set_bit(TRIGGER_NETDEV_RX, rules);
+		if (val & QCA808X_LED_SPEED10_ON)
+			set_bit(TRIGGER_NETDEV_LINK_10, rules);
+		if (val & QCA808X_LED_SPEED100_ON)
+			set_bit(TRIGGER_NETDEV_LINK_100, rules);
+		if (val & QCA808X_LED_SPEED1000_ON)
+			set_bit(TRIGGER_NETDEV_LINK_1000, rules);
+		if (val & QCA808X_LED_HALF_DUPLEX_ON)
+			set_bit(TRIGGER_NETDEV_HALF_DUPLEX, rules);
+		if (val & QCA808X_LED_FULL_DUPLEX_ON)
+			set_bit(TRIGGER_NETDEV_FULL_DUPLEX, rules);
+		break;
+	case PORT_FIBRE:
+		/* HW control pattern bits are in LED FORCE reg */
+		reg = QCA807X_MMD7_LED_FORCE_CTRL(index);
+		val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
+		if (val & QCA807X_LED_FIBER_TXACT_BLK_EN)
+			set_bit(TRIGGER_NETDEV_TX, rules);
+		if (val & QCA807X_LED_FIBER_RXACT_BLK_EN)
+			set_bit(TRIGGER_NETDEV_RX, rules);
+		if (val & QCA807X_LED_FIBER_100FX_ON_EN)
+			set_bit(TRIGGER_NETDEV_LINK_100, rules);
+		if (val & QCA807X_LED_FIBER_1000BX_ON_EN)
+			set_bit(TRIGGER_NETDEV_LINK_1000, rules);
+		if (val & QCA807X_LED_FIBER_HDX_ON_EN)
+			set_bit(TRIGGER_NETDEV_HALF_DUPLEX, rules);
+		if (val & QCA807X_LED_FIBER_FDX_ON_EN)
+			set_bit(TRIGGER_NETDEV_FULL_DUPLEX, rules);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int qca807x_led_hw_control_reset(struct phy_device *phydev, u8 index)
+{
+	u16 reg, mask;
+
+	if (index > 1)
+		return -EINVAL;
+
+	switch (phydev->port) {
+	case PORT_TP:
+		reg = QCA807X_MMD7_LED_CTRL(index);
+		mask = QCA808X_LED_PATTERN_MASK;
+		break;
+	case PORT_FIBRE:
+		/* HW control pattern bits are in LED FORCE reg */
+		reg = QCA807X_MMD7_LED_FORCE_CTRL(index);
+		mask = QCA807X_LED_FIBER_PATTERN_MASK;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg, mask);
+}
+
+static int qca807x_led_brightness_set(struct phy_device *phydev,
+				      u8 index, enum led_brightness value)
+{
+	u16 reg;
+	int ret;
+
+	if (index > 1)
+		return -EINVAL;
+
+	/* If we are setting off the LED reset any hw control rule */
+	if (!value) {
+		ret = qca807x_led_hw_control_reset(phydev, index);
+		if (ret)
+			return ret;
+	}
+
+	reg = QCA807X_MMD7_LED_FORCE_CTRL(index);
+	return qca808x_led_reg_brightness_set(phydev, reg, value);
+}
+
+static int qca807x_led_blink_set(struct phy_device *phydev, u8 index,
+				 unsigned long *delay_on,
+				 unsigned long *delay_off)
+{
+	u16 reg;
+
+	if (index > 1)
+		return -EINVAL;
+
+	reg = QCA807X_MMD7_LED_FORCE_CTRL(index);
+	return qca808x_led_reg_blink_set(phydev, reg, delay_on, delay_off);
+}
+
+#ifdef CONFIG_GPIOLIB
+static int qca807x_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
+{
+	return GPIO_LINE_DIRECTION_OUT;
+}
+
+static int qca807x_gpio_get(struct gpio_chip *gc, unsigned int offset)
+{
+	struct qca807x_gpio_priv *priv = gpiochip_get_data(gc);
+	u16 reg;
+	int val;
+
+	reg = QCA807X_MMD7_LED_FORCE_CTRL(offset);
+	val = phy_read_mmd(priv->phy, MDIO_MMD_AN, reg);
+
+	return !!FIELD_GET(QCA807X_GPIO_FORCE_MODE_MASK, val);
+}
+
+static int qca807x_gpio_set(struct gpio_chip *gc, unsigned int offset, int value)
+{
+	struct qca807x_gpio_priv *priv = gpiochip_get_data(gc);
+	u16 reg;
+	int val;
+
+	reg = QCA807X_MMD7_LED_FORCE_CTRL(offset);
+
+	val = phy_read_mmd(priv->phy, MDIO_MMD_AN, reg);
+	if (val < 0)
+		return val;
+
+	val &= ~QCA807X_GPIO_FORCE_MODE_MASK;
+	val |= QCA807X_GPIO_FORCE_EN;
+	val |= FIELD_PREP(QCA807X_GPIO_FORCE_MODE_MASK, value);
+
+	return phy_write_mmd(priv->phy, MDIO_MMD_AN, reg, val);
+}
+
+static int qca807x_gpio_dir_out(struct gpio_chip *gc, unsigned int offset, int value)
+{
+	return qca807x_gpio_set(gc, offset, value);
+}
+
+static int qca807x_gpio(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct qca807x_gpio_priv *priv;
+	struct gpio_chip *gc;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->phy = phydev;
+
+	gc = devm_kzalloc(dev, sizeof(*gc), GFP_KERNEL);
+	if (!gc)
+		return -ENOMEM;
+
+	gc->label = dev_name(dev);
+	gc->base = -1;
+	gc->ngpio = 2;
+	gc->parent = dev;
+	gc->owner = THIS_MODULE;
+	gc->can_sleep = true;
+	gc->get_direction = qca807x_gpio_get_direction;
+	gc->direction_output = qca807x_gpio_dir_out;
+	gc->get = qca807x_gpio_get;
+	gc->set = qca807x_gpio_set;
+
+	return devm_gpiochip_add_data(dev, gc, priv);
+}
+#endif
+
+static int qca807x_read_fiber_status(struct phy_device *phydev)
+{
+	bool changed;
+	int ss, err;
+
+	err = genphy_c37_read_status(phydev, &changed);
+	if (err || !changed)
+		return err;
+
+	/* Read the QCA807x PHY-Specific Status register fiber page,
+	 * which indicates the speed and duplex that the PHY is actually
+	 * using, irrespective of whether we are in autoneg mode or not.
+	 */
+	ss = phy_read(phydev, AT803X_SPECIFIC_STATUS);
+	if (ss < 0)
+		return ss;
+
+	phydev->speed = SPEED_UNKNOWN;
+	phydev->duplex = DUPLEX_UNKNOWN;
+	if (ss & AT803X_SS_SPEED_DUPLEX_RESOLVED) {
+		switch (FIELD_GET(AT803X_SS_SPEED_MASK, ss)) {
+		case AT803X_SS_SPEED_100:
+			phydev->speed = SPEED_100;
+			break;
+		case AT803X_SS_SPEED_1000:
+			phydev->speed = SPEED_1000;
+			break;
+		}
+
+		if (ss & AT803X_SS_DUPLEX)
+			phydev->duplex = DUPLEX_FULL;
+		else
+			phydev->duplex = DUPLEX_HALF;
+	}
+
+	return 0;
+}
+
+static int qca807x_read_status(struct phy_device *phydev)
+{
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported)) {
+		switch (phydev->port) {
+		case PORT_FIBRE:
+			return qca807x_read_fiber_status(phydev);
+		case PORT_TP:
+			return at803x_read_status(phydev);
+		default:
+			return -EINVAL;
+		}
+	}
+
+	return at803x_read_status(phydev);
+}
+
+static int qca807x_phy_package_probe_once(struct phy_device *phydev)
+{
+	struct qca807x_shared_priv *priv = phy_package_get_priv(phydev);
+	struct device_node *np = phy_package_get_node(phydev);
+	unsigned int tx_drive_strength;
+	const char *package_mode_name;
+
+	/* Default to 600mw if not defined */
+	if (of_property_read_u32(np, "qcom,tx-drive-strength-milliwatt",
+				 &tx_drive_strength))
+		tx_drive_strength = 600;
+
+	switch (tx_drive_strength) {
+	case 140:
+		priv->tx_drive_strength = PQSGMII_TX_DRIVER_140MV;
+		break;
+	case 160:
+		priv->tx_drive_strength = PQSGMII_TX_DRIVER_160MV;
+		break;
+	case 180:
+		priv->tx_drive_strength = PQSGMII_TX_DRIVER_180MV;
+		break;
+	case 200:
+		priv->tx_drive_strength = PQSGMII_TX_DRIVER_200MV;
+		break;
+	case 220:
+		priv->tx_drive_strength = PQSGMII_TX_DRIVER_220MV;
+		break;
+	case 240:
+		priv->tx_drive_strength = PQSGMII_TX_DRIVER_240MV;
+		break;
+	case 260:
+		priv->tx_drive_strength = PQSGMII_TX_DRIVER_260MV;
+		break;
+	case 280:
+		priv->tx_drive_strength = PQSGMII_TX_DRIVER_280MV;
+		break;
+	case 300:
+		priv->tx_drive_strength = PQSGMII_TX_DRIVER_300MV;
+		break;
+	case 320:
+		priv->tx_drive_strength = PQSGMII_TX_DRIVER_320MV;
+		break;
+	case 400:
+		priv->tx_drive_strength = PQSGMII_TX_DRIVER_400MV;
+		break;
+	case 500:
+		priv->tx_drive_strength = PQSGMII_TX_DRIVER_500MV;
+		break;
+	case 600:
+		priv->tx_drive_strength = PQSGMII_TX_DRIVER_600MV;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	priv->package_mode = PHY_INTERFACE_MODE_NA;
+	if (!of_property_read_string(np, "qcom,package-mode",
+				     &package_mode_name)) {
+		if (!strcasecmp(package_mode_name,
+				phy_modes(PHY_INTERFACE_MODE_PSGMII)))
+			priv->package_mode = PHY_INTERFACE_MODE_PSGMII;
+		else if (!strcasecmp(package_mode_name,
+				     phy_modes(PHY_INTERFACE_MODE_QSGMII)))
+			priv->package_mode = PHY_INTERFACE_MODE_QSGMII;
+		else
+			return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int qca807x_phy_package_config_init_once(struct phy_device *phydev)
+{
+	struct qca807x_shared_priv *priv = phy_package_get_priv(phydev);
+	int val, ret;
+
+	/* Make sure PHY follow PHY package mode if enforced */
+	if (priv->package_mode != PHY_INTERFACE_MODE_NA &&
+	    phydev->interface != priv->package_mode)
+		return -EINVAL;
+
+	phy_lock_mdio_bus(phydev);
+
+	/* Set correct PHY package mode */
+	val = __phy_package_read(phydev, QCA807X_COMBO_ADDR,
+				 QCA807X_CHIP_CONFIGURATION);
+	val &= ~QCA807X_CHIP_CONFIGURATION_MODE_CFG_MASK;
+	/* package_mode can be QSGMII or PSGMII and we validate
+	 * this in probe_once.
+	 * With package_mode to NA, we default to PSGMII.
+	 */
+	switch (priv->package_mode) {
+	case PHY_INTERFACE_MODE_QSGMII:
+		val |= QCA807X_CHIP_CONFIGURATION_MODE_QSGMII_SGMII;
+		break;
+	case PHY_INTERFACE_MODE_PSGMII:
+	default:
+		val |= QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_ALL_COPPER;
+	}
+	ret = __phy_package_write(phydev, QCA807X_COMBO_ADDR,
+				  QCA807X_CHIP_CONFIGURATION, val);
+	if (ret)
+		goto exit;
+
+	/* After mode change Serdes reset is required */
+	val = __phy_package_read(phydev, QCA807X_PQSGMII_ADDR,
+				 PQSGMII_CTRL_REG);
+	val &= ~PQSGMII_ANALOG_SW_RESET;
+	ret = __phy_package_write(phydev, QCA807X_PQSGMII_ADDR,
+				  PQSGMII_CTRL_REG, val);
+	if (ret)
+		goto exit;
+
+	msleep(SERDES_RESET_SLEEP);
+
+	val = __phy_package_read(phydev, QCA807X_PQSGMII_ADDR,
+				 PQSGMII_CTRL_REG);
+	val |= PQSGMII_ANALOG_SW_RESET;
+	ret = __phy_package_write(phydev, QCA807X_PQSGMII_ADDR,
+				  PQSGMII_CTRL_REG, val);
+	if (ret)
+		goto exit;
+
+	/* Workaround to enable AZ transmitting ability */
+	val = __phy_package_read_mmd(phydev, QCA807X_PQSGMII_ADDR,
+				     MDIO_MMD_PMAPMD, PQSGMII_MODE_CTRL);
+	val &= ~PQSGMII_MODE_CTRL_AZ_WORKAROUND_MASK;
+	ret = __phy_package_write_mmd(phydev, QCA807X_PQSGMII_ADDR,
+				      MDIO_MMD_PMAPMD, PQSGMII_MODE_CTRL, val);
+	if (ret)
+		goto exit;
+
+	/* Set PQSGMII TX AMP strength */
+	val = __phy_package_read(phydev, QCA807X_PQSGMII_ADDR,
+				 PQSGMII_DRIVE_CONTROL_1);
+	val &= ~PQSGMII_TX_DRIVER_MASK;
+	val |= FIELD_PREP(PQSGMII_TX_DRIVER_MASK, priv->tx_drive_strength);
+	ret = __phy_package_write(phydev, QCA807X_PQSGMII_ADDR,
+				  PQSGMII_DRIVE_CONTROL_1, val);
+	if (ret)
+		goto exit;
+
+	/* Prevent PSGMII going into hibernation via PSGMII self test */
+	val = __phy_package_read_mmd(phydev, QCA807X_COMBO_ADDR,
+				     MDIO_MMD_PCS, PQSGMII_MMD3_SERDES_CONTROL);
+	val &= ~BIT(1);
+	ret = __phy_package_write_mmd(phydev, QCA807X_COMBO_ADDR,
+				      MDIO_MMD_PCS, PQSGMII_MMD3_SERDES_CONTROL, val);
+
+exit:
+	phy_unlock_mdio_bus(phydev);
+
+	return ret;
+}
+
+static int qca807x_configure_serdes(struct phy_port *port, bool enable,
+				    phy_interface_t interface)
+{
+	struct phy_device *phydev = port_phydev(port);
+	int ret;
+
+	if (!phydev)
+		return -ENODEV;
+
+	if (enable) {
+		/* Set PHY mode to PSGMII combo (1/4 copper + combo ports) mode */
+		ret = phy_modify(phydev,
+				 QCA807X_CHIP_CONFIGURATION,
+				 QCA807X_CHIP_CONFIGURATION_MODE_CFG_MASK,
+				 QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_FIBER);
+		if (ret)
+			return ret;
+		/* Enable fiber mode autodection (1000Base-X or 100Base-FX) */
+		ret = phy_set_bits_mmd(phydev,
+				       MDIO_MMD_AN,
+				       QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION,
+				       QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION_EN);
+		if (ret)
+			return ret;
+	}
+
+	phydev->port = enable ? PORT_FIBRE : PORT_TP;
+
+	return phy_modify(phydev, QCA807X_CHIP_CONFIGURATION,
+			  QCA807X_BT_BX_REG_SEL,
+			  enable ? 0 : QCA807X_BT_BX_REG_SEL);
+}
+
+static const struct phy_port_ops qca807x_serdes_port_ops = {
+	.configure_mii = qca807x_configure_serdes,
+};
+
+static int qca807x_attach_mii_port(struct phy_device *phydev,
+				   struct phy_port *port)
+{
+	__set_bit(PHY_INTERFACE_MODE_1000BASEX, port->interfaces);
+	__set_bit(PHY_INTERFACE_MODE_100BASEX, port->interfaces);
+
+	port->ops = &qca807x_serdes_port_ops;
+
+	return 0;
+}
+
+static int qca807x_probe(struct phy_device *phydev)
+{
+	struct device_node *node = phydev->mdio.dev.of_node;
+	struct qca807x_shared_priv *shared_priv;
+	struct device *dev = &phydev->mdio.dev;
+	struct qca807x_priv *priv;
+	int ret;
+
+	ret = devm_of_phy_package_join(dev, phydev, sizeof(*shared_priv));
+	if (ret)
+		return ret;
+
+	if (phy_package_probe_once(phydev)) {
+		ret = qca807x_phy_package_probe_once(phydev);
+		if (ret)
+			return ret;
+	}
+
+	shared_priv = phy_package_get_priv(phydev);
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dac_full_amplitude = of_property_read_bool(node, "qcom,dac-full-amplitude");
+	priv->dac_full_bias_current = of_property_read_bool(node, "qcom,dac-full-bias-current");
+	priv->dac_disable_bias_current_tweak = of_property_read_bool(node,
+								     "qcom,dac-disable-bias-current-tweak");
+
+#if IS_ENABLED(CONFIG_GPIOLIB)
+	/* Do not register a GPIO controller unless flagged for it */
+	if (of_property_read_bool(node, "gpio-controller")) {
+		ret = qca807x_gpio(phydev);
+		if (ret)
+			return ret;
+	}
+#endif
+
+	/* Attach SFP bus on combo port*/
+	if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION)) {
+		phydev->max_n_ports = 2;
+
+		linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported);
+		linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->advertising);
+	}
+
+	phydev->priv = priv;
+
+	return 0;
+}
+
+static int qca807x_config_init(struct phy_device *phydev)
+{
+	struct qca807x_priv *priv = phydev->priv;
+	u16 control_dac;
+	int ret;
+
+	if (phy_package_init_once(phydev)) {
+		ret = qca807x_phy_package_config_init_once(phydev);
+		if (ret)
+			return ret;
+	}
+
+	ret = qcom_phy_counter_config(phydev);
+	if (ret)
+		return ret;
+
+	control_dac = phy_read_mmd(phydev, MDIO_MMD_AN,
+				   QCA807X_MMD7_1000BASE_T_POWER_SAVE_PER_CABLE_LENGTH);
+	control_dac &= ~QCA807X_CONTROL_DAC_MASK;
+	if (!priv->dac_full_amplitude)
+		control_dac |= QCA807X_CONTROL_DAC_DSP_AMPLITUDE;
+	if (!priv->dac_full_bias_current)
+		control_dac |= QCA807X_CONTROL_DAC_DSP_BIAS_CURRENT;
+	if (!priv->dac_disable_bias_current_tweak)
+		control_dac |= QCA807X_CONTROL_DAC_BIAS_CURRENT_TWEAK;
+	return phy_write_mmd(phydev, MDIO_MMD_AN,
+			     QCA807X_MMD7_1000BASE_T_POWER_SAVE_PER_CABLE_LENGTH,
+			     control_dac);
+}
+
+static int qca807x_update_stats(struct phy_device *phydev)
+{
+	struct qca807x_priv *priv = phydev->priv;
+
+	return qcom_phy_update_stats(phydev, &priv->hw_stats);
+}
+
+static void qca807x_get_phy_stats(struct phy_device *phydev,
+				  struct ethtool_eth_phy_stats *eth_stats,
+				  struct ethtool_phy_stats *stats)
+{
+	struct qca807x_priv *priv = phydev->priv;
+
+	qcom_phy_get_stats(stats, priv->hw_stats);
+}
+
+static struct phy_driver qca807x_drivers[] = {
+	{
+		PHY_ID_MATCH_EXACT(PHY_ID_QCA8072),
+		.name           = "Qualcomm QCA8072",
+		.flags		= PHY_POLL_CABLE_TEST,
+		/* PHY_GBIT_FEATURES */
+		.probe		= qca807x_probe,
+		.config_init	= qca807x_config_init,
+		.read_status	= qca807x_read_status,
+		.config_intr	= at803x_config_intr,
+		.handle_interrupt = at803x_handle_interrupt,
+		.soft_reset	= genphy_soft_reset,
+		.get_tunable	= at803x_get_tunable,
+		.set_tunable	= at803x_set_tunable,
+		.resume		= genphy_resume,
+		.suspend	= genphy_suspend,
+		.cable_test_start	= qca807x_cable_test_start,
+		.cable_test_get_status	= qca808x_cable_test_get_status,
+		.update_stats		= qca807x_update_stats,
+		.get_phy_stats		= qca807x_get_phy_stats,
+		.set_wol		= at8031_set_wol,
+		.get_wol		= at803x_get_wol,
+		.attach_mii_port	= qca807x_attach_mii_port,
+	},
+	{
+		PHY_ID_MATCH_EXACT(PHY_ID_QCA8075),
+		.name           = "Qualcomm QCA8075",
+		.flags		= PHY_POLL_CABLE_TEST,
+		/* PHY_GBIT_FEATURES */
+		.probe		= qca807x_probe,
+		.config_init	= qca807x_config_init,
+		.read_status	= qca807x_read_status,
+		.config_intr	= at803x_config_intr,
+		.handle_interrupt = at803x_handle_interrupt,
+		.soft_reset	= genphy_soft_reset,
+		.get_tunable	= at803x_get_tunable,
+		.set_tunable	= at803x_set_tunable,
+		.resume		= genphy_resume,
+		.suspend	= genphy_suspend,
+		.cable_test_start	= qca807x_cable_test_start,
+		.cable_test_get_status	= qca808x_cable_test_get_status,
+		.led_brightness_set = qca807x_led_brightness_set,
+		.led_blink_set = qca807x_led_blink_set,
+		.led_hw_is_supported = qca807x_led_hw_is_supported,
+		.led_hw_control_set = qca807x_led_hw_control_set,
+		.led_hw_control_get = qca807x_led_hw_control_get,
+		.update_stats		= qca807x_update_stats,
+		.get_phy_stats		= qca807x_get_phy_stats,
+		.set_wol		= at8031_set_wol,
+		.get_wol		= at803x_get_wol,
+		.attach_mii_port	= qca807x_attach_mii_port,
+	},
+};
+module_phy_driver(qca807x_drivers);
+
+static const struct mdio_device_id __maybe_unused qca807x_tbl[] = {
+	{ PHY_ID_MATCH_EXACT(PHY_ID_QCA8072) },
+	{ PHY_ID_MATCH_EXACT(PHY_ID_QCA8075) },
+	{ }
+};
+
+MODULE_AUTHOR("Robert Marko <robert.marko@sartura.hr>");
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_DESCRIPTION("Qualcomm QCA807x PHY driver");
+MODULE_DEVICE_TABLE(mdio, qca807x_tbl);
+MODULE_LICENSE("GPL");

linux-7.2.3/drivers/net/phy/qcom/qca808x.c

@@ -0,0 +1,686 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <linux/phy.h>
+#include <linux/module.h>
+
+#include "qcom.h"
+
+/* ADC threshold */
+#define QCA808X_PHY_DEBUG_ADC_THRESHOLD		0x2c80
+#define QCA808X_ADC_THRESHOLD_MASK		GENMASK(7, 0)
+#define QCA808X_ADC_THRESHOLD_80MV		0
+#define QCA808X_ADC_THRESHOLD_100MV		0xf0
+#define QCA808X_ADC_THRESHOLD_200MV		0x0f
+#define QCA808X_ADC_THRESHOLD_300MV		0xff
+
+/* CLD control */
+#define QCA808X_PHY_MMD3_ADDR_CLD_CTRL7		0x8007
+#define QCA808X_8023AZ_AFE_CTRL_MASK		GENMASK(8, 4)
+#define QCA808X_8023AZ_AFE_EN			0x90
+
+/* AZ control */
+#define QCA808X_PHY_MMD3_AZ_TRAINING_CTRL	0x8008
+#define QCA808X_MMD3_AZ_TRAINING_VAL		0x1c32
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB	0x8014
+#define QCA808X_MSE_THRESHOLD_20DB_VALUE	0x529
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB	0x800E
+#define QCA808X_MSE_THRESHOLD_17DB_VALUE	0x341
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB	0x801E
+#define QCA808X_MSE_THRESHOLD_27DB_VALUE	0x419
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB	0x8020
+#define QCA808X_MSE_THRESHOLD_28DB_VALUE	0x341
+
+#define QCA808X_PHY_MMD7_TOP_OPTION1		0x901c
+#define QCA808X_TOP_OPTION1_DATA		0x0
+
+#define QCA808X_PHY_MMD3_DEBUG_1		0xa100
+#define QCA808X_MMD3_DEBUG_1_VALUE		0x9203
+#define QCA808X_PHY_MMD3_DEBUG_2		0xa101
+#define QCA808X_MMD3_DEBUG_2_VALUE		0x48ad
+#define QCA808X_PHY_MMD3_DEBUG_3		0xa103
+#define QCA808X_MMD3_DEBUG_3_VALUE		0x1698
+#define QCA808X_PHY_MMD3_DEBUG_4		0xa105
+#define QCA808X_MMD3_DEBUG_4_VALUE		0x8001
+#define QCA808X_PHY_MMD3_DEBUG_5		0xa106
+#define QCA808X_MMD3_DEBUG_5_VALUE		0x1111
+#define QCA808X_PHY_MMD3_DEBUG_6		0xa011
+#define QCA808X_MMD3_DEBUG_6_VALUE		0x5f85
+
+/* master/slave seed config */
+#define QCA808X_PHY_DEBUG_LOCAL_SEED		9
+#define QCA808X_MASTER_SLAVE_SEED_ENABLE	BIT(1)
+#define QCA808X_MASTER_SLAVE_SEED_CFG		GENMASK(12, 2)
+#define QCA808X_MASTER_SLAVE_SEED_RANGE		0x32
+
+/* Hibernation yields lower power consumpiton in contrast with normal operation mode.
+ * when the copper cable is unplugged, the PHY enters into hibernation mode in about 10s.
+ */
+#define QCA808X_DBG_AN_TEST			0xb
+#define QCA808X_HIBERNATION_EN			BIT(15)
+
+#define QCA808X_MMD7_LED2_CTRL			0x8074
+#define QCA808X_MMD7_LED2_FORCE_CTRL		0x8075
+#define QCA808X_MMD7_LED1_CTRL			0x8076
+#define QCA808X_MMD7_LED1_FORCE_CTRL		0x8077
+#define QCA808X_MMD7_LED0_CTRL			0x8078
+#define QCA808X_MMD7_LED_CTRL(x)		(0x8078 - ((x) * 2))
+
+#define QCA808X_MMD7_LED0_FORCE_CTRL		0x8079
+#define QCA808X_MMD7_LED_FORCE_CTRL(x)		(0x8079 - ((x) * 2))
+
+#define QCA808X_MMD7_LED_POLARITY_CTRL		0x901a
+/* QSDK sets by default 0x46 to this reg that sets BIT 6 for
+ * LED to active high. It's not clear what BIT 3 and BIT 4 does.
+ */
+#define QCA808X_LED_ACTIVE_HIGH			BIT(6)
+
+/* QCA808X 1G chip type */
+#define QCA808X_PHY_MMD7_CHIP_TYPE		0x901d
+#define QCA808X_PHY_CHIP_TYPE_1G		BIT(0)
+
+#define QCA8081_PHY_SERDES_MMD1_FIFO_CTRL	0x9072
+#define QCA8081_PHY_FIFO_RSTN			BIT(11)
+
+#define QCA8081_PHY_ID				0x004dd101
+
+MODULE_DESCRIPTION("Qualcomm Atheros QCA808X PHY driver");
+MODULE_AUTHOR("Matus Ujhelyi");
+MODULE_LICENSE("GPL");
+
+struct qca808x_priv {
+	int led_polarity_mode;
+	struct qcom_phy_hw_stats hw_stats;
+};
+
+static int qca808x_phy_fast_retrain_config(struct phy_device *phydev)
+{
+	int ret;
+
+	/* Enable fast retrain */
+	ret = genphy_c45_fast_retrain(phydev, true);
+	if (ret)
+		return ret;
+
+	phy_write_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_TOP_OPTION1,
+		      QCA808X_TOP_OPTION1_DATA);
+	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB,
+		      QCA808X_MSE_THRESHOLD_20DB_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB,
+		      QCA808X_MSE_THRESHOLD_17DB_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB,
+		      QCA808X_MSE_THRESHOLD_27DB_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB,
+		      QCA808X_MSE_THRESHOLD_28DB_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_1,
+		      QCA808X_MMD3_DEBUG_1_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_4,
+		      QCA808X_MMD3_DEBUG_4_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_5,
+		      QCA808X_MMD3_DEBUG_5_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_3,
+		      QCA808X_MMD3_DEBUG_3_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_6,
+		      QCA808X_MMD3_DEBUG_6_VALUE);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_2,
+		      QCA808X_MMD3_DEBUG_2_VALUE);
+
+	return 0;
+}
+
+static int qca808x_phy_ms_seed_enable(struct phy_device *phydev, bool enable)
+{
+	u16 seed_value;
+
+	if (!enable)
+		return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
+				QCA808X_MASTER_SLAVE_SEED_ENABLE, 0);
+
+	seed_value = get_random_u32_below(QCA808X_MASTER_SLAVE_SEED_RANGE);
+	return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
+			QCA808X_MASTER_SLAVE_SEED_CFG | QCA808X_MASTER_SLAVE_SEED_ENABLE,
+			FIELD_PREP(QCA808X_MASTER_SLAVE_SEED_CFG, seed_value) |
+			QCA808X_MASTER_SLAVE_SEED_ENABLE);
+}
+
+static bool qca808x_is_prefer_master(struct phy_device *phydev)
+{
+	return (phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_FORCE) ||
+		(phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_PREFERRED);
+}
+
+static bool qca808x_has_fast_retrain_or_slave_seed(struct phy_device *phydev)
+{
+	return linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
+}
+
+static bool qca808x_is_1g_only(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_CHIP_TYPE);
+	if (ret < 0)
+		return true;
+
+	return !!(QCA808X_PHY_CHIP_TYPE_1G & ret);
+}
+
+static void qca808x_fill_possible_interfaces(struct phy_device *phydev)
+{
+	unsigned long *possible = phydev->possible_interfaces;
+
+	__set_bit(PHY_INTERFACE_MODE_SGMII, possible);
+
+	if (!qca808x_is_1g_only(phydev))
+		__set_bit(PHY_INTERFACE_MODE_2500BASEX, possible);
+}
+
+static int qca808x_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct qca808x_priv *priv;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	/* Init LED polarity mode to -1 */
+	priv->led_polarity_mode = -1;
+
+	phydev->priv = priv;
+
+	return 0;
+}
+
+static int qca808x_config_init(struct phy_device *phydev)
+{
+	struct qca808x_priv *priv = phydev->priv;
+	int ret;
+
+	/* Default to LED Active High if active-low not in DT */
+	if (priv->led_polarity_mode == -1) {
+		ret = phy_set_bits_mmd(phydev, MDIO_MMD_AN,
+				       QCA808X_MMD7_LED_POLARITY_CTRL,
+				       QCA808X_LED_ACTIVE_HIGH);
+		if (ret)
+			return ret;
+	}
+
+	/* Active adc&vga on 802.3az for the link 1000M and 100M */
+	ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_ADDR_CLD_CTRL7,
+			     QCA808X_8023AZ_AFE_CTRL_MASK, QCA808X_8023AZ_AFE_EN);
+	if (ret)
+		return ret;
+
+	/* Adjust the threshold on 802.3az for the link 1000M */
+	ret = phy_write_mmd(phydev, MDIO_MMD_PCS,
+			    QCA808X_PHY_MMD3_AZ_TRAINING_CTRL,
+			    QCA808X_MMD3_AZ_TRAINING_VAL);
+	if (ret)
+		return ret;
+
+	if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
+		/* Config the fast retrain for the link 2500M */
+		ret = qca808x_phy_fast_retrain_config(phydev);
+		if (ret)
+			return ret;
+
+		ret = genphy_read_master_slave(phydev);
+		if (ret < 0)
+			return ret;
+
+		if (!qca808x_is_prefer_master(phydev)) {
+			/* Enable seed and configure lower ramdom seed to make phy
+			 * linked as slave mode.
+			 */
+			ret = qca808x_phy_ms_seed_enable(phydev, true);
+			if (ret)
+				return ret;
+		}
+	}
+
+	qca808x_fill_possible_interfaces(phydev);
+
+	ret = qcom_phy_counter_config(phydev);
+	if (ret)
+		return ret;
+
+	/* Configure adc threshold as 100mv for the link 10M */
+	return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_ADC_THRESHOLD,
+				     QCA808X_ADC_THRESHOLD_MASK,
+				     QCA808X_ADC_THRESHOLD_100MV);
+}
+
+static int qca808x_read_status(struct phy_device *phydev)
+{
+	struct at803x_ss_mask ss_mask = { 0 };
+	int ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_STAT);
+	if (ret < 0)
+		return ret;
+
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->lp_advertising,
+			 ret & MDIO_AN_10GBT_STAT_LP2_5G);
+
+	ret = genphy_read_status(phydev);
+	if (ret)
+		return ret;
+
+	/* qca8081 takes the different bits for speed value from at803x */
+	ss_mask.speed_mask = QCA808X_SS_SPEED_MASK;
+	ss_mask.speed_shift = __bf_shf(QCA808X_SS_SPEED_MASK);
+	ret = at803x_read_specific_status(phydev, ss_mask);
+	if (ret < 0)
+		return ret;
+
+	if (phydev->link) {
+		if (phydev->speed == SPEED_2500)
+			phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
+		else
+			phydev->interface = PHY_INTERFACE_MODE_SGMII;
+	} else {
+		/* generate seed as a lower random value to make PHY linked as SLAVE easily,
+		 * except for master/slave configuration fault detected or the master mode
+		 * preferred.
+		 *
+		 * the reason for not putting this code into the function link_change_notify is
+		 * the corner case where the link partner is also the qca8081 PHY and the seed
+		 * value is configured as the same value, the link can't be up and no link change
+		 * occurs.
+		 */
+		if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
+			if (phydev->master_slave_state == MASTER_SLAVE_STATE_ERR ||
+			    qca808x_is_prefer_master(phydev)) {
+				qca808x_phy_ms_seed_enable(phydev, false);
+			} else {
+				qca808x_phy_ms_seed_enable(phydev, true);
+			}
+		}
+	}
+
+	return 0;
+}
+
+static int qca808x_soft_reset(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = genphy_soft_reset(phydev);
+	if (ret < 0)
+		return ret;
+
+	if (qca808x_has_fast_retrain_or_slave_seed(phydev))
+		ret = qca808x_phy_ms_seed_enable(phydev, true);
+
+	return ret;
+}
+
+static int qca808x_cable_test_start(struct phy_device *phydev)
+{
+	int ret;
+
+	/* perform CDT with the following configs:
+	 * 1. disable hibernation.
+	 * 2. force PHY working in MDI mode.
+	 * 3. for PHY working in 1000BaseT.
+	 * 4. configure the threshold.
+	 */
+
+	ret = at803x_debug_reg_mask(phydev, QCA808X_DBG_AN_TEST, QCA808X_HIBERNATION_EN, 0);
+	if (ret < 0)
+		return ret;
+
+	ret = at803x_config_mdix(phydev, ETH_TP_MDI);
+	if (ret < 0)
+		return ret;
+
+	/* Force 1000base-T needs to configure PMA/PMD and MII_BMCR */
+	phydev->duplex = DUPLEX_FULL;
+	phydev->speed = SPEED_1000;
+	ret = genphy_c45_pma_setup_forced(phydev);
+	if (ret < 0)
+		return ret;
+
+	ret = genphy_setup_forced(phydev);
+	if (ret < 0)
+		return ret;
+
+	/* configure the thresholds for open, short, pair ok test */
+	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8074, 0xc040);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8076, 0xc040);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8077, 0xa060);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8078, 0xc050);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807a, 0xc060);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807e, 0xb060);
+
+	return 0;
+}
+
+static int qca808x_get_features(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = genphy_c45_pma_read_abilities(phydev);
+	if (ret)
+		return ret;
+
+	/* The autoneg ability is not existed in bit3 of MMD7.1,
+	 * but it is supported by qca808x PHY, so we add it here
+	 * manually.
+	 */
+	linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported);
+
+	/* As for the qca8081 1G version chip, the 2500baseT ability is also
+	 * existed in the bit0 of MMD1.21, we need to remove it manually if
+	 * it is the qca8081 1G chip according to the bit0 of MMD7.0x901d.
+	 */
+	if (qca808x_is_1g_only(phydev))
+		linkmode_clear_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
+
+	return 0;
+}
+
+static int qca808x_config_aneg(struct phy_device *phydev)
+{
+	int phy_ctrl = 0;
+	int ret;
+
+	ret = at803x_prepare_config_aneg(phydev);
+	if (ret)
+		return ret;
+
+	/* The reg MII_BMCR also needs to be configured for force mode, the
+	 * genphy_config_aneg is also needed.
+	 */
+	if (phydev->autoneg == AUTONEG_DISABLE)
+		genphy_c45_pma_setup_forced(phydev);
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->advertising))
+		phy_ctrl = MDIO_AN_10GBT_CTRL_ADV2_5G;
+
+	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_CTRL,
+				     MDIO_AN_10GBT_CTRL_ADV2_5G, phy_ctrl);
+	if (ret < 0)
+		return ret;
+
+	return __genphy_config_aneg(phydev, ret);
+}
+
+static void qca808x_link_change_notify(struct phy_device *phydev)
+{
+	/* Assert interface sgmii fifo on link down, deassert it on link up,
+	 * the interface device address is always phy address added by 1.
+	 */
+	mdiobus_c45_modify_changed(phydev->mdio.bus, phydev->mdio.addr + 1,
+				   MDIO_MMD_PMAPMD, QCA8081_PHY_SERDES_MMD1_FIFO_CTRL,
+				   QCA8081_PHY_FIFO_RSTN,
+				   phydev->link ? QCA8081_PHY_FIFO_RSTN : 0);
+}
+
+static int qca808x_led_parse_netdev(struct phy_device *phydev, unsigned long rules,
+				    u16 *offload_trigger)
+{
+	/* Parsing specific to netdev trigger */
+	if (test_bit(TRIGGER_NETDEV_TX, &rules))
+		*offload_trigger |= QCA808X_LED_TX_BLINK;
+	if (test_bit(TRIGGER_NETDEV_RX, &rules))
+		*offload_trigger |= QCA808X_LED_RX_BLINK;
+	if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
+		*offload_trigger |= QCA808X_LED_SPEED10_ON;
+	if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
+		*offload_trigger |= QCA808X_LED_SPEED100_ON;
+	if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
+		*offload_trigger |= QCA808X_LED_SPEED1000_ON;
+	if (test_bit(TRIGGER_NETDEV_LINK_2500, &rules))
+		*offload_trigger |= QCA808X_LED_SPEED2500_ON;
+	if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules))
+		*offload_trigger |= QCA808X_LED_HALF_DUPLEX_ON;
+	if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules))
+		*offload_trigger |= QCA808X_LED_FULL_DUPLEX_ON;
+
+	if (rules && !*offload_trigger)
+		return -EOPNOTSUPP;
+
+	/* Enable BLINK_CHECK_BYPASS by default to make the LED
+	 * blink even with duplex or speed mode not enabled.
+	 */
+	*offload_trigger |= QCA808X_LED_BLINK_CHECK_BYPASS;
+
+	return 0;
+}
+
+static int qca808x_led_hw_control_enable(struct phy_device *phydev, u8 index)
+{
+	u16 reg;
+
+	if (index > 2)
+		return -EINVAL;
+
+	reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+	return qca808x_led_reg_hw_control_enable(phydev, reg);
+}
+
+static int qca808x_led_hw_is_supported(struct phy_device *phydev, u8 index,
+				       unsigned long rules)
+{
+	u16 offload_trigger = 0;
+
+	if (index > 2)
+		return -EINVAL;
+
+	return qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
+}
+
+static int qca808x_led_hw_control_set(struct phy_device *phydev, u8 index,
+				      unsigned long rules)
+{
+	u16 reg, offload_trigger = 0;
+	int ret;
+
+	if (index > 2)
+		return -EINVAL;
+
+	reg = QCA808X_MMD7_LED_CTRL(index);
+
+	ret = qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
+	if (ret)
+		return ret;
+
+	ret = qca808x_led_hw_control_enable(phydev, index);
+	if (ret)
+		return ret;
+
+	return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+			      QCA808X_LED_PATTERN_MASK,
+			      offload_trigger);
+}
+
+static bool qca808x_led_hw_control_status(struct phy_device *phydev, u8 index)
+{
+	u16 reg;
+
+	if (index > 2)
+		return false;
+
+	reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+	return qca808x_led_reg_hw_control_status(phydev, reg);
+}
+
+static int qca808x_led_hw_control_get(struct phy_device *phydev, u8 index,
+				      unsigned long *rules)
+{
+	u16 reg;
+	int val;
+
+	if (index > 2)
+		return -EINVAL;
+
+	/* Check if we have hw control enabled */
+	if (qca808x_led_hw_control_status(phydev, index))
+		return -EINVAL;
+
+	reg = QCA808X_MMD7_LED_CTRL(index);
+
+	val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
+	if (val & QCA808X_LED_TX_BLINK)
+		set_bit(TRIGGER_NETDEV_TX, rules);
+	if (val & QCA808X_LED_RX_BLINK)
+		set_bit(TRIGGER_NETDEV_RX, rules);
+	if (val & QCA808X_LED_SPEED10_ON)
+		set_bit(TRIGGER_NETDEV_LINK_10, rules);
+	if (val & QCA808X_LED_SPEED100_ON)
+		set_bit(TRIGGER_NETDEV_LINK_100, rules);
+	if (val & QCA808X_LED_SPEED1000_ON)
+		set_bit(TRIGGER_NETDEV_LINK_1000, rules);
+	if (val & QCA808X_LED_SPEED2500_ON)
+		set_bit(TRIGGER_NETDEV_LINK_2500, rules);
+	if (val & QCA808X_LED_HALF_DUPLEX_ON)
+		set_bit(TRIGGER_NETDEV_HALF_DUPLEX, rules);
+	if (val & QCA808X_LED_FULL_DUPLEX_ON)
+		set_bit(TRIGGER_NETDEV_FULL_DUPLEX, rules);
+
+	return 0;
+}
+
+static int qca808x_led_hw_control_reset(struct phy_device *phydev, u8 index)
+{
+	u16 reg;
+
+	if (index > 2)
+		return -EINVAL;
+
+	reg = QCA808X_MMD7_LED_CTRL(index);
+
+	return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
+				  QCA808X_LED_PATTERN_MASK);
+}
+
+static int qca808x_led_brightness_set(struct phy_device *phydev,
+				      u8 index, enum led_brightness value)
+{
+	u16 reg;
+	int ret;
+
+	if (index > 2)
+		return -EINVAL;
+
+	if (!value) {
+		ret = qca808x_led_hw_control_reset(phydev, index);
+		if (ret)
+			return ret;
+	}
+
+	reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+	return qca808x_led_reg_brightness_set(phydev, reg, value);
+}
+
+static int qca808x_led_blink_set(struct phy_device *phydev, u8 index,
+				 unsigned long *delay_on,
+				 unsigned long *delay_off)
+{
+	u16 reg;
+
+	if (index > 2)
+		return -EINVAL;
+
+	reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+	return qca808x_led_reg_blink_set(phydev, reg, delay_on, delay_off);
+}
+
+static int qca808x_led_polarity_set(struct phy_device *phydev, int index,
+				    unsigned long modes)
+{
+	struct qca808x_priv *priv = phydev->priv;
+	bool active_low = false;
+	u32 mode;
+
+	for_each_set_bit(mode, &modes, __PHY_LED_MODES_NUM) {
+		switch (mode) {
+		case PHY_LED_ACTIVE_LOW:
+			active_low = true;
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	/* PHY polarity is global and can't be set per LED.
+	 * To detect this, check if last requested polarity mode
+	 * match the new one.
+	 */
+	if (priv->led_polarity_mode >= 0 &&
+	    priv->led_polarity_mode != active_low) {
+		phydev_err(phydev, "PHY polarity is global. Mismatched polarity on different LED\n");
+		return -EINVAL;
+	}
+
+	/* Save the last PHY polarity mode */
+	priv->led_polarity_mode = active_low;
+
+	return phy_modify_mmd(phydev, MDIO_MMD_AN,
+			      QCA808X_MMD7_LED_POLARITY_CTRL,
+			      QCA808X_LED_ACTIVE_HIGH,
+			      active_low ? 0 : QCA808X_LED_ACTIVE_HIGH);
+}
+
+static int qca808x_update_stats(struct phy_device *phydev)
+{
+	struct qca808x_priv *priv = phydev->priv;
+
+	return qcom_phy_update_stats(phydev, &priv->hw_stats);
+}
+
+static void qca808x_get_phy_stats(struct phy_device *phydev,
+				  struct ethtool_eth_phy_stats *eth_stats,
+				  struct ethtool_phy_stats *stats)
+{
+	struct qca808x_priv *priv = phydev->priv;
+
+	qcom_phy_get_stats(stats, priv->hw_stats);
+}
+
+static struct phy_driver qca808x_driver[] = {
+{
+	/* Qualcomm QCA8081 */
+	PHY_ID_MATCH_EXACT(QCA8081_PHY_ID),
+	.name			= "Qualcomm QCA8081",
+	.flags			= PHY_POLL_CABLE_TEST,
+	.probe			= qca808x_probe,
+	.config_intr		= at803x_config_intr,
+	.handle_interrupt	= at803x_handle_interrupt,
+	.get_tunable		= at803x_get_tunable,
+	.set_tunable		= at803x_set_tunable,
+	.set_wol		= at8031_set_wol,
+	.get_wol		= at803x_get_wol,
+	.get_features		= qca808x_get_features,
+	.config_aneg		= qca808x_config_aneg,
+	.suspend		= genphy_suspend,
+	.resume			= genphy_resume,
+	.read_status		= qca808x_read_status,
+	.config_init		= qca808x_config_init,
+	.soft_reset		= qca808x_soft_reset,
+	.cable_test_start	= qca808x_cable_test_start,
+	.cable_test_get_status	= qca808x_cable_test_get_status,
+	.link_change_notify	= qca808x_link_change_notify,
+	.led_brightness_set	= qca808x_led_brightness_set,
+	.led_blink_set		= qca808x_led_blink_set,
+	.led_hw_is_supported	= qca808x_led_hw_is_supported,
+	.led_hw_control_set	= qca808x_led_hw_control_set,
+	.led_hw_control_get	= qca808x_led_hw_control_get,
+	.led_polarity_set	= qca808x_led_polarity_set,
+	.update_stats		= qca808x_update_stats,
+	.get_phy_stats		= qca808x_get_phy_stats,
+}, };
+
+module_phy_driver(qca808x_driver);
+
+static const struct mdio_device_id __maybe_unused qca808x_tbl[] = {
+	{ PHY_ID_MATCH_EXACT(QCA8081_PHY_ID) },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(mdio, qca808x_tbl);

linux-7.2.3/drivers/net/phy/qcom/qca83xx.c

@@ -0,0 +1,269 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <linux/phy.h>
+#include <linux/module.h>
+
+#include "qcom.h"
+
+#define AT803X_DEBUG_REG_3C			0x3C
+
+#define AT803X_DEBUG_REG_GREEN			0x3D
+#define   AT803X_DEBUG_GATE_CLK_IN1000		BIT(6)
+
+#define MDIO_AZ_DEBUG				0x800D
+
+#define QCA8327_A_PHY_ID			0x004dd033
+#define QCA8327_B_PHY_ID			0x004dd034
+#define QCA8337_PHY_ID				0x004dd036
+
+#define QCA8K_DEVFLAGS_REVISION_MASK		GENMASK(2, 0)
+
+static struct at803x_hw_stat qca83xx_hw_stats[] = {
+	{ "phy_idle_errors", 0xa, GENMASK(7, 0), PHY},
+	{ "phy_receive_errors", 0x15, GENMASK(15, 0), PHY},
+	{ "eee_wake_errors", 0x16, GENMASK(15, 0), MMD},
+};
+
+struct qca83xx_priv {
+	u64 stats[ARRAY_SIZE(qca83xx_hw_stats)];
+};
+
+MODULE_DESCRIPTION("Qualcomm Atheros QCA83XX PHY driver");
+MODULE_AUTHOR("Matus Ujhelyi");
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_LICENSE("GPL");
+
+static int qca83xx_get_sset_count(struct phy_device *phydev)
+{
+	return ARRAY_SIZE(qca83xx_hw_stats);
+}
+
+static void qca83xx_get_strings(struct phy_device *phydev, u8 *data)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(qca83xx_hw_stats); i++)
+		ethtool_puts(&data, qca83xx_hw_stats[i].string);
+}
+
+static u64 qca83xx_get_stat(struct phy_device *phydev, int i)
+{
+	struct at803x_hw_stat stat = qca83xx_hw_stats[i];
+	struct qca83xx_priv *priv = phydev->priv;
+	int val;
+	u64 ret;
+
+	if (stat.access_type == MMD)
+		val = phy_read_mmd(phydev, MDIO_MMD_PCS, stat.reg);
+	else
+		val = phy_read(phydev, stat.reg);
+
+	if (val < 0) {
+		ret = U64_MAX;
+	} else {
+		val = val & stat.mask;
+		priv->stats[i] += val;
+		ret = priv->stats[i];
+	}
+
+	return ret;
+}
+
+static void qca83xx_get_stats(struct phy_device *phydev,
+			      struct ethtool_stats *stats, u64 *data)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(qca83xx_hw_stats); i++)
+		data[i] = qca83xx_get_stat(phydev, i);
+}
+
+static int qca83xx_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct qca83xx_priv *priv;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	phydev->priv = priv;
+
+	return 0;
+}
+
+static int qca83xx_config_init(struct phy_device *phydev)
+{
+	u8 switch_revision;
+
+	switch_revision = phydev->dev_flags & QCA8K_DEVFLAGS_REVISION_MASK;
+
+	switch (switch_revision) {
+	case 1:
+		/* For 100M waveform */
+		at803x_debug_reg_write(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0x02ea);
+		/* Turn on Gigabit clock */
+		at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x68a0);
+		break;
+
+	case 2:
+		phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV, 0x0);
+		fallthrough;
+	case 4:
+		phy_write_mmd(phydev, MDIO_MMD_PCS, MDIO_AZ_DEBUG, 0x803f);
+		at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x6860);
+		at803x_debug_reg_write(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0x2c46);
+		at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3C, 0x6000);
+		break;
+	}
+
+	/* Following original QCA sourcecode set port to prefer master */
+	phy_set_bits(phydev, MII_CTRL1000, CTL1000_PREFER_MASTER);
+
+	return 0;
+}
+
+static int qca8327_config_init(struct phy_device *phydev)
+{
+	/* QCA8327 require DAC amplitude adjustment for 100m set to +6%.
+	 * Disable on init and enable only with 100m speed following
+	 * qca original source code.
+	 */
+	at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
+			      QCA8327_DEBUG_MANU_CTRL_EN, 0);
+
+	return qca83xx_config_init(phydev);
+}
+
+static void qca83xx_link_change_notify(struct phy_device *phydev)
+{
+	/* Set DAC Amplitude adjustment to +6% for 100m on link running */
+	if (phydev->state == PHY_RUNNING) {
+		if (phydev->speed == SPEED_100)
+			at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
+					      QCA8327_DEBUG_MANU_CTRL_EN,
+					      QCA8327_DEBUG_MANU_CTRL_EN);
+	} else {
+		/* Reset DAC Amplitude adjustment */
+		at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL,
+				      QCA8327_DEBUG_MANU_CTRL_EN, 0);
+	}
+}
+
+static int qca83xx_resume(struct phy_device *phydev)
+{
+	int ret, val;
+
+	/* Skip reset if not suspended */
+	if (!phydev->suspended)
+		return 0;
+
+	/* Reinit the port, reset values set by suspend */
+	qca83xx_config_init(phydev);
+
+	/* Reset the port on port resume */
+	phy_set_bits(phydev, MII_BMCR, BMCR_RESET | BMCR_ANENABLE);
+
+	/* On resume from suspend the switch execute a reset and
+	 * restart auto-negotiation. Wait for reset to complete.
+	 */
+	ret = phy_read_poll_timeout(phydev, MII_BMCR, val, !(val & BMCR_RESET),
+				    50000, 600000, true);
+	if (ret)
+		return ret;
+
+	usleep_range(1000, 2000);
+
+	return 0;
+}
+
+static int qca83xx_suspend(struct phy_device *phydev)
+{
+	at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_GREEN,
+			      AT803X_DEBUG_GATE_CLK_IN1000, 0);
+
+	at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL,
+			      AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE |
+			      AT803X_DEBUG_HIB_CTRL_SEL_RST_80U, 0);
+
+	return 0;
+}
+
+static int qca8337_suspend(struct phy_device *phydev)
+{
+	/* Only QCA8337 support actual suspend. */
+	genphy_suspend(phydev);
+
+	return qca83xx_suspend(phydev);
+}
+
+static int qca8327_suspend(struct phy_device *phydev)
+{
+	u16 mask = 0;
+
+	/* QCA8327 cause port unreliability when phy suspend
+	 * is set.
+	 */
+	mask |= ~(BMCR_SPEED1000 | BMCR_FULLDPLX);
+	phy_modify(phydev, MII_BMCR, mask, 0);
+
+	return qca83xx_suspend(phydev);
+}
+
+static struct phy_driver qca83xx_driver[] = {
+{
+	/* QCA8337 */
+	PHY_ID_MATCH_EXACT(QCA8337_PHY_ID),
+	.name			= "Qualcomm Atheros 8337 internal PHY",
+	/* PHY_GBIT_FEATURES */
+	.probe			= qca83xx_probe,
+	.flags			= PHY_IS_INTERNAL,
+	.config_init		= qca83xx_config_init,
+	.soft_reset		= genphy_soft_reset,
+	.get_sset_count		= qca83xx_get_sset_count,
+	.get_strings		= qca83xx_get_strings,
+	.get_stats		= qca83xx_get_stats,
+	.suspend		= qca8337_suspend,
+	.resume			= qca83xx_resume,
+}, {
+	/* QCA8327-A from switch QCA8327-AL1A */
+	PHY_ID_MATCH_EXACT(QCA8327_A_PHY_ID),
+	.name			= "Qualcomm Atheros 8327-A internal PHY",
+	/* PHY_GBIT_FEATURES */
+	.link_change_notify	= qca83xx_link_change_notify,
+	.probe			= qca83xx_probe,
+	.flags			= PHY_IS_INTERNAL,
+	.config_init		= qca8327_config_init,
+	.soft_reset		= genphy_soft_reset,
+	.get_sset_count		= qca83xx_get_sset_count,
+	.get_strings		= qca83xx_get_strings,
+	.get_stats		= qca83xx_get_stats,
+	.suspend		= qca8327_suspend,
+	.resume			= qca83xx_resume,
+}, {
+	/* QCA8327-B from switch QCA8327-BL1A */
+	PHY_ID_MATCH_EXACT(QCA8327_B_PHY_ID),
+	.name			= "Qualcomm Atheros 8327-B internal PHY",
+	/* PHY_GBIT_FEATURES */
+	.link_change_notify	= qca83xx_link_change_notify,
+	.probe			= qca83xx_probe,
+	.flags			= PHY_IS_INTERNAL,
+	.config_init		= qca8327_config_init,
+	.soft_reset		= genphy_soft_reset,
+	.get_sset_count		= qca83xx_get_sset_count,
+	.get_strings		= qca83xx_get_strings,
+	.get_stats		= qca83xx_get_stats,
+	.suspend		= qca8327_suspend,
+	.resume			= qca83xx_resume,
+}, };
+
+module_phy_driver(qca83xx_driver);
+
+static const struct mdio_device_id __maybe_unused qca83xx_tbl[] = {
+	{ PHY_ID_MATCH_EXACT(QCA8337_PHY_ID) },
+	{ PHY_ID_MATCH_EXACT(QCA8327_A_PHY_ID) },
+	{ PHY_ID_MATCH_EXACT(QCA8327_B_PHY_ID) },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(mdio, qca83xx_tbl);

linux-7.2.3/drivers/net/phy/qcom/qcom-phy-lib.c

@@ -0,0 +1,776 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <linux/phy.h>
+#include <linux/module.h>
+
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool_netlink.h>
+
+#include "qcom.h"
+
+MODULE_DESCRIPTION("Qualcomm PHY driver Common Functions");
+MODULE_AUTHOR("Matus Ujhelyi");
+MODULE_AUTHOR("Christian Marangi <ansuelsmth@gmail.com>");
+MODULE_LICENSE("GPL");
+
+int at803x_debug_reg_read(struct phy_device *phydev, u16 reg)
+{
+	int ret;
+
+	ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg);
+	if (ret < 0)
+		return ret;
+
+	return phy_read(phydev, AT803X_DEBUG_DATA);
+}
+EXPORT_SYMBOL_GPL(at803x_debug_reg_read);
+
+int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
+			  u16 clear, u16 set)
+{
+	u16 val;
+	int ret;
+
+	ret = at803x_debug_reg_read(phydev, reg);
+	if (ret < 0)
+		return ret;
+
+	val = ret & 0xffff;
+	val &= ~clear;
+	val |= set;
+
+	return phy_write(phydev, AT803X_DEBUG_DATA, val);
+}
+EXPORT_SYMBOL_GPL(at803x_debug_reg_mask);
+
+int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data)
+{
+	int ret;
+
+	ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg);
+	if (ret < 0)
+		return ret;
+
+	return phy_write(phydev, AT803X_DEBUG_DATA, data);
+}
+EXPORT_SYMBOL_GPL(at803x_debug_reg_write);
+
+int at803x_set_wol(struct phy_device *phydev,
+		   struct ethtool_wolinfo *wol)
+{
+	int ret, irq_enabled;
+
+	if (wol->wolopts & WAKE_MAGIC) {
+		struct net_device *ndev = phydev->attached_dev;
+		const u8 *mac;
+		unsigned int i;
+		static const unsigned int offsets[] = {
+			AT803X_LOC_MAC_ADDR_32_47_OFFSET,
+			AT803X_LOC_MAC_ADDR_16_31_OFFSET,
+			AT803X_LOC_MAC_ADDR_0_15_OFFSET,
+		};
+
+		if (!ndev)
+			return -ENODEV;
+
+		mac = (const u8 *)ndev->dev_addr;
+
+		if (!is_valid_ether_addr(mac))
+			return -EINVAL;
+
+		for (i = 0; i < 3; i++)
+			phy_write_mmd(phydev, MDIO_MMD_PCS, offsets[i],
+				      mac[(i * 2) + 1] | (mac[(i * 2)] << 8));
+
+		/* Enable WOL interrupt */
+		ret = phy_modify(phydev, AT803X_INTR_ENABLE, 0, AT803X_INTR_ENABLE_WOL);
+		if (ret)
+			return ret;
+	} else {
+		/* Disable WOL interrupt */
+		ret = phy_modify(phydev, AT803X_INTR_ENABLE, AT803X_INTR_ENABLE_WOL, 0);
+		if (ret)
+			return ret;
+	}
+
+	/* Clear WOL status */
+	ret = phy_read(phydev, AT803X_INTR_STATUS);
+	if (ret < 0)
+		return ret;
+
+	/* Check if there are other interrupts except for WOL triggered when PHY is
+	 * in interrupt mode, only the interrupts enabled by AT803X_INTR_ENABLE can
+	 * be passed up to the interrupt PIN.
+	 */
+	irq_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
+	if (irq_enabled < 0)
+		return irq_enabled;
+
+	irq_enabled &= ~AT803X_INTR_ENABLE_WOL;
+	if (ret & irq_enabled && !phy_polling_mode(phydev))
+		phy_trigger_machine(phydev);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(at803x_set_wol);
+
+int at8031_set_wol(struct phy_device *phydev,
+		   struct ethtool_wolinfo *wol)
+{
+	int ret;
+
+	/* First setup MAC address and enable WOL interrupt */
+	ret = at803x_set_wol(phydev, wol);
+	if (ret)
+		return ret;
+
+	if (wol->wolopts & WAKE_MAGIC)
+		/* Enable WOL function for 1588 */
+		ret = phy_modify_mmd(phydev, MDIO_MMD_PCS,
+				     AT803X_PHY_MMD3_WOL_CTRL,
+				     0, AT803X_WOL_EN);
+	else
+		/* Disable WoL function for 1588 */
+		ret = phy_modify_mmd(phydev, MDIO_MMD_PCS,
+				     AT803X_PHY_MMD3_WOL_CTRL,
+				     AT803X_WOL_EN, 0);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(at8031_set_wol);
+
+void at803x_get_wol(struct phy_device *phydev,
+		    struct ethtool_wolinfo *wol)
+{
+	int value;
+
+	wol->supported = WAKE_MAGIC;
+	wol->wolopts = 0;
+
+	value = phy_read(phydev, AT803X_INTR_ENABLE);
+	if (value < 0)
+		return;
+
+	if (value & AT803X_INTR_ENABLE_WOL)
+		wol->wolopts |= WAKE_MAGIC;
+}
+EXPORT_SYMBOL_GPL(at803x_get_wol);
+
+int at803x_ack_interrupt(struct phy_device *phydev)
+{
+	int err;
+
+	err = phy_read(phydev, AT803X_INTR_STATUS);
+
+	return (err < 0) ? err : 0;
+}
+EXPORT_SYMBOL_GPL(at803x_ack_interrupt);
+
+int at803x_config_intr(struct phy_device *phydev)
+{
+	int err;
+	int value;
+
+	value = phy_read(phydev, AT803X_INTR_ENABLE);
+
+	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
+		/* Clear any pending interrupts */
+		err = at803x_ack_interrupt(phydev);
+		if (err)
+			return err;
+
+		value |= AT803X_INTR_ENABLE_AUTONEG_ERR;
+		value |= AT803X_INTR_ENABLE_SPEED_CHANGED;
+		value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED;
+		value |= AT803X_INTR_ENABLE_LINK_FAIL;
+		value |= AT803X_INTR_ENABLE_LINK_SUCCESS;
+
+		err = phy_write(phydev, AT803X_INTR_ENABLE, value);
+	} else {
+		err = phy_write(phydev, AT803X_INTR_ENABLE, 0);
+		if (err)
+			return err;
+
+		/* Clear any pending interrupts */
+		err = at803x_ack_interrupt(phydev);
+	}
+
+	return err;
+}
+EXPORT_SYMBOL_GPL(at803x_config_intr);
+
+irqreturn_t at803x_handle_interrupt(struct phy_device *phydev)
+{
+	int irq_status, int_enabled;
+
+	irq_status = phy_read(phydev, AT803X_INTR_STATUS);
+	if (irq_status < 0) {
+		phy_error(phydev);
+		return IRQ_NONE;
+	}
+
+	/* Read the current enabled interrupts */
+	int_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
+	if (int_enabled < 0) {
+		phy_error(phydev);
+		return IRQ_NONE;
+	}
+
+	/* See if this was one of our enabled interrupts */
+	if (!(irq_status & int_enabled))
+		return IRQ_NONE;
+
+	phy_trigger_machine(phydev);
+
+	return IRQ_HANDLED;
+}
+EXPORT_SYMBOL_GPL(at803x_handle_interrupt);
+
+int at803x_read_specific_status(struct phy_device *phydev,
+				struct at803x_ss_mask ss_mask)
+{
+	int ss;
+
+	/* Read the AT8035 PHY-Specific Status register, which indicates the
+	 * speed and duplex that the PHY is actually using, irrespective of
+	 * whether we are in autoneg mode or not.
+	 */
+	ss = phy_read(phydev, AT803X_SPECIFIC_STATUS);
+	if (ss < 0)
+		return ss;
+
+	if (ss & AT803X_SS_SPEED_DUPLEX_RESOLVED) {
+		int sfc, speed;
+
+		sfc = phy_read(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL);
+		if (sfc < 0)
+			return sfc;
+
+		speed = ss & ss_mask.speed_mask;
+		speed >>= ss_mask.speed_shift;
+
+		switch (speed) {
+		case AT803X_SS_SPEED_10:
+			phydev->speed = SPEED_10;
+			break;
+		case AT803X_SS_SPEED_100:
+			phydev->speed = SPEED_100;
+			break;
+		case AT803X_SS_SPEED_1000:
+			phydev->speed = SPEED_1000;
+			break;
+		case QCA808X_SS_SPEED_2500:
+			phydev->speed = SPEED_2500;
+			break;
+		}
+		if (ss & AT803X_SS_DUPLEX)
+			phydev->duplex = DUPLEX_FULL;
+		else
+			phydev->duplex = DUPLEX_HALF;
+
+		if (ss & AT803X_SS_MDIX)
+			phydev->mdix = ETH_TP_MDI_X;
+		else
+			phydev->mdix = ETH_TP_MDI;
+
+		switch (FIELD_GET(AT803X_SFC_MDI_CROSSOVER_MODE_M, sfc)) {
+		case AT803X_SFC_MANUAL_MDI:
+			phydev->mdix_ctrl = ETH_TP_MDI;
+			break;
+		case AT803X_SFC_MANUAL_MDIX:
+			phydev->mdix_ctrl = ETH_TP_MDI_X;
+			break;
+		case AT803X_SFC_AUTOMATIC_CROSSOVER:
+			phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+			break;
+		}
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(at803x_read_specific_status);
+
+int at803x_config_mdix(struct phy_device *phydev, u8 ctrl)
+{
+	u16 val;
+
+	switch (ctrl) {
+	case ETH_TP_MDI:
+		val = AT803X_SFC_MANUAL_MDI;
+		break;
+	case ETH_TP_MDI_X:
+		val = AT803X_SFC_MANUAL_MDIX;
+		break;
+	case ETH_TP_MDI_AUTO:
+		val = AT803X_SFC_AUTOMATIC_CROSSOVER;
+		break;
+	default:
+		return 0;
+	}
+
+	return phy_modify_changed(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL,
+			  AT803X_SFC_MDI_CROSSOVER_MODE_M,
+			  FIELD_PREP(AT803X_SFC_MDI_CROSSOVER_MODE_M, val));
+}
+EXPORT_SYMBOL_GPL(at803x_config_mdix);
+
+int at803x_prepare_config_aneg(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = at803x_config_mdix(phydev, phydev->mdix_ctrl);
+	if (ret < 0)
+		return ret;
+
+	/* Changes of the midx bits are disruptive to the normal operation;
+	 * therefore any changes to these registers must be followed by a
+	 * software reset to take effect.
+	 */
+	if (ret == 1) {
+		ret = genphy_soft_reset(phydev);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(at803x_prepare_config_aneg);
+
+int at803x_read_status(struct phy_device *phydev)
+{
+	struct at803x_ss_mask ss_mask = { 0 };
+	int err, old_link = phydev->link;
+
+	/* Update the link, but return if there was an error */
+	err = genphy_update_link(phydev);
+	if (err)
+		return err;
+
+	/* why bother the PHY if nothing can have changed */
+	if (phydev->autoneg == AUTONEG_ENABLE && old_link && phydev->link)
+		return 0;
+
+	phydev->speed = SPEED_UNKNOWN;
+	phydev->duplex = DUPLEX_UNKNOWN;
+	phydev->pause = 0;
+	phydev->asym_pause = 0;
+
+	err = genphy_read_lpa(phydev);
+	if (err < 0)
+		return err;
+
+	ss_mask.speed_mask = AT803X_SS_SPEED_MASK;
+	ss_mask.speed_shift = __bf_shf(AT803X_SS_SPEED_MASK);
+	err = at803x_read_specific_status(phydev, ss_mask);
+	if (err < 0)
+		return err;
+
+	if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete)
+		phy_resolve_aneg_pause(phydev);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(at803x_read_status);
+
+static int at803x_get_downshift(struct phy_device *phydev, u8 *d)
+{
+	int val;
+
+	val = phy_read(phydev, AT803X_SMART_SPEED);
+	if (val < 0)
+		return val;
+
+	if (val & AT803X_SMART_SPEED_ENABLE)
+		*d = FIELD_GET(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, val) + 2;
+	else
+		*d = DOWNSHIFT_DEV_DISABLE;
+
+	return 0;
+}
+
+static int at803x_set_downshift(struct phy_device *phydev, u8 cnt)
+{
+	u16 mask, set;
+	int ret;
+
+	switch (cnt) {
+	case DOWNSHIFT_DEV_DEFAULT_COUNT:
+		cnt = AT803X_DEFAULT_DOWNSHIFT;
+		fallthrough;
+	case AT803X_MIN_DOWNSHIFT ... AT803X_MAX_DOWNSHIFT:
+		set = AT803X_SMART_SPEED_ENABLE |
+		      AT803X_SMART_SPEED_BYPASS_TIMER |
+		      FIELD_PREP(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, cnt - 2);
+		mask = AT803X_SMART_SPEED_RETRY_LIMIT_MASK;
+		break;
+	case DOWNSHIFT_DEV_DISABLE:
+		set = 0;
+		mask = AT803X_SMART_SPEED_ENABLE |
+		       AT803X_SMART_SPEED_BYPASS_TIMER;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	ret = phy_modify_changed(phydev, AT803X_SMART_SPEED, mask, set);
+
+	/* After changing the smart speed settings, we need to perform a
+	 * software reset, use phy_init_hw() to make sure we set the
+	 * reapply any values which might got lost during software reset.
+	 */
+	if (ret == 1)
+		ret = phy_init_hw(phydev);
+
+	return ret;
+}
+
+int at803x_get_tunable(struct phy_device *phydev,
+		       struct ethtool_tunable *tuna, void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return at803x_get_downshift(phydev, data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+EXPORT_SYMBOL_GPL(at803x_get_tunable);
+
+int at803x_set_tunable(struct phy_device *phydev,
+		       struct ethtool_tunable *tuna, const void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return at803x_set_downshift(phydev, *(const u8 *)data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+EXPORT_SYMBOL_GPL(at803x_set_tunable);
+
+int at803x_cdt_fault_length(int dt)
+{
+	/* According to the datasheet the distance to the fault is
+	 * DELTA_TIME * 0.824 meters.
+	 *
+	 * The author suspect the correct formula is:
+	 *
+	 *   fault_distance = DELTA_TIME * (c * VF) / 125MHz / 2
+	 *
+	 * where c is the speed of light, VF is the velocity factor of
+	 * the twisted pair cable, 125MHz the counter frequency and
+	 * we need to divide by 2 because the hardware will measure the
+	 * round trip time to the fault and back to the PHY.
+	 *
+	 * With a VF of 0.69 we get the factor 0.824 mentioned in the
+	 * datasheet.
+	 */
+	return (dt * 824) / 10;
+}
+EXPORT_SYMBOL_GPL(at803x_cdt_fault_length);
+
+int at803x_cdt_start(struct phy_device *phydev, u32 cdt_start)
+{
+	return phy_write(phydev, AT803X_CDT, cdt_start);
+}
+EXPORT_SYMBOL_GPL(at803x_cdt_start);
+
+int at803x_cdt_wait_for_completion(struct phy_device *phydev,
+				   u32 cdt_en)
+{
+	int val, ret;
+
+	/* One test run takes about 25ms */
+	ret = phy_read_poll_timeout(phydev, AT803X_CDT, val,
+				    !(val & cdt_en),
+				    30000, 100000, true);
+
+	return ret < 0 ? ret : 0;
+}
+EXPORT_SYMBOL_GPL(at803x_cdt_wait_for_completion);
+
+static bool qca808x_cdt_fault_length_valid(int cdt_code)
+{
+	switch (cdt_code) {
+	case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
+	case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static int qca808x_cable_test_result_trans(int cdt_code)
+{
+	switch (cdt_code) {
+	case QCA808X_CDT_STATUS_STAT_NORMAL:
+		return ETHTOOL_A_CABLE_RESULT_CODE_OK;
+	case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
+		return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
+	case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
+		return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
+	case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
+		return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT;
+	case QCA808X_CDT_STATUS_STAT_FAIL:
+	default:
+		return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
+	}
+}
+
+static int qca808x_cdt_fault_length(struct phy_device *phydev, int pair,
+				    int result)
+{
+	int val;
+	u32 cdt_length_reg = 0;
+
+	switch (pair) {
+	case ETHTOOL_A_CABLE_PAIR_A:
+		cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_A;
+		break;
+	case ETHTOOL_A_CABLE_PAIR_B:
+		cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_B;
+		break;
+	case ETHTOOL_A_CABLE_PAIR_C:
+		cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_C;
+		break;
+	case ETHTOOL_A_CABLE_PAIR_D:
+		cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_D;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	val = phy_read_mmd(phydev, MDIO_MMD_PCS, cdt_length_reg);
+	if (val < 0)
+		return val;
+
+	if (result == ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT)
+		val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_SAME_SHORT, val);
+	else
+		val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT, val);
+
+	return at803x_cdt_fault_length(val);
+}
+
+static int qca808x_cable_test_get_pair_status(struct phy_device *phydev, u8 pair,
+					      u16 status)
+{
+	int length, result;
+	u16 pair_code;
+
+	switch (pair) {
+	case ETHTOOL_A_CABLE_PAIR_A:
+		pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_A, status);
+		break;
+	case ETHTOOL_A_CABLE_PAIR_B:
+		pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_B, status);
+		break;
+	case ETHTOOL_A_CABLE_PAIR_C:
+		pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_C, status);
+		break;
+	case ETHTOOL_A_CABLE_PAIR_D:
+		pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_D, status);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	result = qca808x_cable_test_result_trans(pair_code);
+	ethnl_cable_test_result(phydev, pair, result);
+
+	if (qca808x_cdt_fault_length_valid(pair_code)) {
+		length = qca808x_cdt_fault_length(phydev, pair, result);
+		ethnl_cable_test_fault_length(phydev, pair, length);
+	}
+
+	return 0;
+}
+
+int qca808x_cable_test_get_status(struct phy_device *phydev, bool *finished)
+{
+	int ret, val;
+
+	*finished = false;
+
+	val = QCA808X_CDT_ENABLE_TEST |
+	      QCA808X_CDT_LENGTH_UNIT;
+	ret = at803x_cdt_start(phydev, val);
+	if (ret)
+		return ret;
+
+	ret = at803x_cdt_wait_for_completion(phydev, QCA808X_CDT_ENABLE_TEST);
+	if (ret)
+		return ret;
+
+	val = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA808X_MMD3_CDT_STATUS);
+	if (val < 0)
+		return val;
+
+	ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_A, val);
+	if (ret)
+		return ret;
+
+	ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_B, val);
+	if (ret)
+		return ret;
+
+	ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_C, val);
+	if (ret)
+		return ret;
+
+	ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_D, val);
+	if (ret)
+		return ret;
+
+	*finished = true;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(qca808x_cable_test_get_status);
+
+int qca808x_led_reg_hw_control_enable(struct phy_device *phydev, u16 reg)
+{
+	return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
+				  QCA808X_LED_FORCE_EN);
+}
+EXPORT_SYMBOL_GPL(qca808x_led_reg_hw_control_enable);
+
+bool qca808x_led_reg_hw_control_status(struct phy_device *phydev, u16 reg)
+{
+	int val;
+
+	val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
+	return !(val & QCA808X_LED_FORCE_EN);
+}
+EXPORT_SYMBOL_GPL(qca808x_led_reg_hw_control_status);
+
+int qca808x_led_reg_brightness_set(struct phy_device *phydev,
+				   u16 reg, enum led_brightness value)
+{
+	return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+			      QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
+			      QCA808X_LED_FORCE_EN | (value ? QCA808X_LED_FORCE_ON :
+							      QCA808X_LED_FORCE_OFF));
+}
+EXPORT_SYMBOL_GPL(qca808x_led_reg_brightness_set);
+
+int qca808x_led_reg_blink_set(struct phy_device *phydev, u16 reg,
+			      unsigned long *delay_on,
+			      unsigned long *delay_off)
+{
+	int ret;
+
+	/* Set blink to 50% off, 50% on at 4Hz by default */
+	ret = phy_modify_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_LED_GLOBAL,
+			     QCA808X_LED_BLINK_FREQ_MASK | QCA808X_LED_BLINK_DUTY_MASK,
+			     QCA808X_LED_BLINK_FREQ_4HZ | QCA808X_LED_BLINK_DUTY_50_50);
+	if (ret)
+		return ret;
+
+	/* We use BLINK_1 for normal blinking */
+	ret = phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+			     QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
+			     QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_BLINK_1);
+	if (ret)
+		return ret;
+
+	/* We set blink to 4Hz, aka 250ms */
+	*delay_on = 250 / 2;
+	*delay_off = 250 / 2;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(qca808x_led_reg_blink_set);
+
+/* Enable CRC checking for both received and transmitted frames to ensure
+ * accurate counter recording. The hardware supports a 32-bit counter,
+ * configure the counter to clear after it is read to facilitate the
+ * implementation of a 64-bit software counter
+ */
+int qcom_phy_counter_config(struct phy_device *phydev)
+{
+	return phy_set_bits_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_CNT_CTRL,
+				QCA808X_MMD7_CNT_CTRL_CRC_CHECK_EN |
+				QCA808X_MMD7_CNT_CTRL_READ_CLEAR_EN);
+}
+EXPORT_SYMBOL_GPL(qcom_phy_counter_config);
+
+int qcom_phy_update_stats(struct phy_device *phydev,
+			  struct qcom_phy_hw_stats *hw_stats)
+{
+	int ret;
+	u32 cnt;
+
+	/* PHY 32-bit counter for RX packets. */
+	ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_CNT_RX_PKT_15_0);
+	if (ret < 0)
+		return ret;
+
+	cnt = ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_CNT_RX_PKT_31_16);
+	if (ret < 0)
+		return ret;
+
+	cnt |= ret << 16;
+	hw_stats->rx_pkts += cnt;
+
+	/* PHY 16-bit counter for RX CRC error packets. */
+	ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_CNT_RX_ERR_PKT);
+	if (ret < 0)
+		return ret;
+
+	hw_stats->rx_err_pkts += ret;
+
+	/* PHY 32-bit counter for TX packets. */
+	ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_CNT_TX_PKT_15_0);
+	if (ret < 0)
+		return ret;
+
+	cnt = ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_CNT_TX_PKT_31_16);
+	if (ret < 0)
+		return ret;
+
+	cnt |= ret << 16;
+	hw_stats->tx_pkts += cnt;
+
+	/* PHY 16-bit counter for TX CRC error packets. */
+	ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_CNT_TX_ERR_PKT);
+	if (ret < 0)
+		return ret;
+
+	hw_stats->tx_err_pkts += ret;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(qcom_phy_update_stats);
+
+void qcom_phy_get_stats(struct ethtool_phy_stats *stats,
+			struct qcom_phy_hw_stats hw_stats)
+{
+	stats->tx_packets = hw_stats.tx_pkts;
+	stats->tx_errors = hw_stats.tx_err_pkts;
+	stats->rx_packets = hw_stats.rx_pkts;
+	stats->rx_errors = hw_stats.rx_err_pkts;
+}
+EXPORT_SYMBOL_GPL(qcom_phy_get_stats);

linux-7.2.3/drivers/net/phy/qcom/qcom.h

@@ -0,0 +1,271 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#define AT803X_SPECIFIC_FUNCTION_CONTROL	0x10
+#define AT803X_SFC_ASSERT_CRS			BIT(11)
+#define AT803X_SFC_FORCE_LINK			BIT(10)
+#define AT803X_SFC_MDI_CROSSOVER_MODE_M		GENMASK(6, 5)
+#define AT803X_SFC_AUTOMATIC_CROSSOVER		0x3
+#define AT803X_SFC_MANUAL_MDIX			0x1
+#define AT803X_SFC_MANUAL_MDI			0x0
+#define AT803X_SFC_SQE_TEST			BIT(2)
+#define AT803X_SFC_POLARITY_REVERSAL		BIT(1)
+#define AT803X_SFC_DISABLE_JABBER		BIT(0)
+
+#define AT803X_SPECIFIC_STATUS			0x11
+#define AT803X_SS_SPEED_MASK			GENMASK(15, 14)
+#define AT803X_SS_SPEED_1000			2
+#define AT803X_SS_SPEED_100			1
+#define AT803X_SS_SPEED_10			0
+#define AT803X_SS_DUPLEX			BIT(13)
+#define AT803X_SS_SPEED_DUPLEX_RESOLVED		BIT(11)
+#define AT803X_SS_MDIX				BIT(6)
+
+#define QCA808X_SS_SPEED_MASK			GENMASK(9, 7)
+#define QCA808X_SS_SPEED_2500			4
+
+#define AT803X_INTR_ENABLE			0x12
+#define AT803X_INTR_ENABLE_AUTONEG_ERR		BIT(15)
+#define AT803X_INTR_ENABLE_SPEED_CHANGED	BIT(14)
+#define AT803X_INTR_ENABLE_DUPLEX_CHANGED	BIT(13)
+#define AT803X_INTR_ENABLE_PAGE_RECEIVED	BIT(12)
+#define AT803X_INTR_ENABLE_LINK_FAIL		BIT(11)
+#define AT803X_INTR_ENABLE_LINK_SUCCESS		BIT(10)
+#define AT803X_INTR_ENABLE_LINK_FAIL_BX		BIT(8)
+#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX	BIT(7)
+#define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE	BIT(5)
+#define AT803X_INTR_ENABLE_POLARITY_CHANGED	BIT(1)
+#define AT803X_INTR_ENABLE_WOL			BIT(0)
+
+#define AT803X_INTR_STATUS			0x13
+
+#define AT803X_SMART_SPEED			0x14
+#define AT803X_SMART_SPEED_ENABLE		BIT(5)
+#define AT803X_SMART_SPEED_RETRY_LIMIT_MASK	GENMASK(4, 2)
+#define AT803X_SMART_SPEED_BYPASS_TIMER		BIT(1)
+
+#define AT803X_CDT				0x16
+#define AT803X_CDT_MDI_PAIR_MASK		GENMASK(9, 8)
+#define AT803X_CDT_ENABLE_TEST			BIT(0)
+#define AT803X_CDT_STATUS			0x1c
+#define AT803X_CDT_STATUS_STAT_NORMAL		0
+#define AT803X_CDT_STATUS_STAT_SHORT		1
+#define AT803X_CDT_STATUS_STAT_OPEN		2
+#define AT803X_CDT_STATUS_STAT_FAIL		3
+#define AT803X_CDT_STATUS_STAT_MASK		GENMASK(9, 8)
+#define AT803X_CDT_STATUS_DELTA_TIME_MASK	GENMASK(7, 0)
+
+#define QCA808X_CDT_ENABLE_TEST			BIT(15)
+#define QCA808X_CDT_INTER_CHECK_DIS		BIT(13)
+#define QCA808X_CDT_STATUS			BIT(11)
+#define QCA808X_CDT_LENGTH_UNIT			BIT(10)
+
+#define QCA808X_MMD3_CDT_STATUS			0x8064
+#define QCA808X_MMD3_CDT_DIAG_PAIR_A		0x8065
+#define QCA808X_MMD3_CDT_DIAG_PAIR_B		0x8066
+#define QCA808X_MMD3_CDT_DIAG_PAIR_C		0x8067
+#define QCA808X_MMD3_CDT_DIAG_PAIR_D		0x8068
+#define QCA808X_CDT_DIAG_LENGTH_SAME_SHORT	GENMASK(15, 8)
+#define QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT	GENMASK(7, 0)
+
+#define QCA808X_CDT_CODE_PAIR_A			GENMASK(15, 12)
+#define QCA808X_CDT_CODE_PAIR_B			GENMASK(11, 8)
+#define QCA808X_CDT_CODE_PAIR_C			GENMASK(7, 4)
+#define QCA808X_CDT_CODE_PAIR_D			GENMASK(3, 0)
+
+#define QCA808X_CDT_STATUS_STAT_TYPE		GENMASK(1, 0)
+#define QCA808X_CDT_STATUS_STAT_FAIL		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 0)
+#define QCA808X_CDT_STATUS_STAT_NORMAL		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 1)
+#define QCA808X_CDT_STATUS_STAT_SAME_OPEN	FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 2)
+#define QCA808X_CDT_STATUS_STAT_SAME_SHORT	FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 3)
+
+#define QCA808X_CDT_STATUS_STAT_MDI		GENMASK(3, 2)
+#define QCA808X_CDT_STATUS_STAT_MDI1		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 1)
+#define QCA808X_CDT_STATUS_STAT_MDI2		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 2)
+#define QCA808X_CDT_STATUS_STAT_MDI3		FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 3)
+
+/* NORMAL are MDI with type set to 0 */
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL	QCA808X_CDT_STATUS_STAT_MDI1
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN		(QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
+									 QCA808X_CDT_STATUS_STAT_MDI1)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT	(QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
+									 QCA808X_CDT_STATUS_STAT_MDI1)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL	QCA808X_CDT_STATUS_STAT_MDI2
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN		(QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
+									 QCA808X_CDT_STATUS_STAT_MDI2)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT	(QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
+									 QCA808X_CDT_STATUS_STAT_MDI2)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL	QCA808X_CDT_STATUS_STAT_MDI3
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN		(QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
+									 QCA808X_CDT_STATUS_STAT_MDI3)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT	(QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
+									 QCA808X_CDT_STATUS_STAT_MDI3)
+
+/* Added for reference of existence but should be handled by wait_for_completion already */
+#define QCA808X_CDT_STATUS_STAT_BUSY		(BIT(1) | BIT(3))
+
+#define QCA808X_MMD7_LED_GLOBAL			0x8073
+#define QCA808X_LED_BLINK_1			GENMASK(11, 6)
+#define QCA808X_LED_BLINK_2			GENMASK(5, 0)
+/* Values are the same for both BLINK_1 and BLINK_2 */
+#define QCA808X_LED_BLINK_FREQ_MASK		GENMASK(5, 3)
+#define QCA808X_LED_BLINK_FREQ_2HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x0)
+#define QCA808X_LED_BLINK_FREQ_4HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x1)
+#define QCA808X_LED_BLINK_FREQ_8HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x2)
+#define QCA808X_LED_BLINK_FREQ_16HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x3)
+#define QCA808X_LED_BLINK_FREQ_32HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x4)
+#define QCA808X_LED_BLINK_FREQ_64HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x5)
+#define QCA808X_LED_BLINK_FREQ_128HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x6)
+#define QCA808X_LED_BLINK_FREQ_256HZ		FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x7)
+#define QCA808X_LED_BLINK_DUTY_MASK		GENMASK(2, 0)
+#define QCA808X_LED_BLINK_DUTY_50_50		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x0)
+#define QCA808X_LED_BLINK_DUTY_75_25		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x1)
+#define QCA808X_LED_BLINK_DUTY_25_75		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x2)
+#define QCA808X_LED_BLINK_DUTY_33_67		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x3)
+#define QCA808X_LED_BLINK_DUTY_67_33		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x4)
+#define QCA808X_LED_BLINK_DUTY_17_83		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x5)
+#define QCA808X_LED_BLINK_DUTY_83_17		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x6)
+#define QCA808X_LED_BLINK_DUTY_8_92		FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x7)
+
+/* LED hw control pattern is the same for every LED */
+#define QCA808X_LED_PATTERN_MASK		GENMASK(15, 0)
+#define QCA808X_LED_SPEED2500_ON		BIT(15)
+#define QCA808X_LED_SPEED2500_BLINK		BIT(14)
+/* Follow blink trigger even if duplex or speed condition doesn't match */
+#define QCA808X_LED_BLINK_CHECK_BYPASS		BIT(13)
+#define QCA808X_LED_FULL_DUPLEX_ON		BIT(12)
+#define QCA808X_LED_HALF_DUPLEX_ON		BIT(11)
+#define QCA808X_LED_TX_BLINK			BIT(10)
+#define QCA808X_LED_RX_BLINK			BIT(9)
+#define QCA808X_LED_TX_ON_10MS			BIT(8)
+#define QCA808X_LED_RX_ON_10MS			BIT(7)
+#define QCA808X_LED_SPEED1000_ON		BIT(6)
+#define QCA808X_LED_SPEED100_ON			BIT(5)
+#define QCA808X_LED_SPEED10_ON			BIT(4)
+#define QCA808X_LED_COLLISION_BLINK		BIT(3)
+#define QCA808X_LED_SPEED1000_BLINK		BIT(2)
+#define QCA808X_LED_SPEED100_BLINK		BIT(1)
+#define QCA808X_LED_SPEED10_BLINK		BIT(0)
+
+/* LED force ctrl is the same for every LED
+ * No documentation exist for this, not even internal one
+ * with NDA as QCOM gives only info about configuring
+ * hw control pattern rules and doesn't indicate any way
+ * to force the LED to specific mode.
+ * These define comes from reverse and testing and maybe
+ * lack of some info or some info are not entirely correct.
+ * For the basic LED control and hw control these finding
+ * are enough to support LED control in all the required APIs.
+ *
+ * On doing some comparison with implementation with qca807x,
+ * it was found that it's 1:1 equal to it and confirms all the
+ * reverse done. It was also found further specification with the
+ * force mode and the blink modes.
+ */
+#define QCA808X_LED_FORCE_EN			BIT(15)
+#define QCA808X_LED_FORCE_MODE_MASK		GENMASK(14, 13)
+#define QCA808X_LED_FORCE_BLINK_1		FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x3)
+#define QCA808X_LED_FORCE_BLINK_2		FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x2)
+#define QCA808X_LED_FORCE_ON			FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x1)
+#define QCA808X_LED_FORCE_OFF			FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x0)
+
+#define AT803X_LOC_MAC_ADDR_0_15_OFFSET		0x804C
+#define AT803X_LOC_MAC_ADDR_16_31_OFFSET	0x804B
+#define AT803X_LOC_MAC_ADDR_32_47_OFFSET	0x804A
+
+#define AT803X_PHY_MMD3_WOL_CTRL		0x8012
+#define AT803X_WOL_EN				BIT(5)
+
+#define AT803X_DEBUG_ADDR			0x1D
+#define AT803X_DEBUG_DATA			0x1E
+
+#define AT803X_DEBUG_ANALOG_TEST_CTRL		0x00
+#define QCA8327_DEBUG_MANU_CTRL_EN		BIT(2)
+#define QCA8337_DEBUG_MANU_CTRL_EN		GENMASK(3, 2)
+#define AT803X_DEBUG_RX_CLK_DLY_EN		BIT(15)
+
+#define AT803X_DEBUG_SYSTEM_CTRL_MODE		0x05
+#define AT803X_DEBUG_TX_CLK_DLY_EN		BIT(8)
+
+#define AT803X_DEBUG_REG_HIB_CTRL		0x0b
+#define   AT803X_DEBUG_HIB_CTRL_SEL_RST_80U	BIT(10)
+#define   AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE	BIT(13)
+#define   AT803X_DEBUG_HIB_CTRL_PS_HIB_EN	BIT(15)
+
+#define AT803X_DEFAULT_DOWNSHIFT		5
+#define AT803X_MIN_DOWNSHIFT			2
+#define AT803X_MAX_DOWNSHIFT			9
+
+#define QCA808X_MMD7_CNT_CTRL			0x8029
+#define QCA808X_MMD7_CNT_CTRL_READ_CLEAR_EN	BIT(1)
+#define QCA808X_MMD7_CNT_CTRL_CRC_CHECK_EN	BIT(0)
+
+#define QCA808X_MMD7_CNT_RX_PKT_31_16		0x802a
+#define QCA808X_MMD7_CNT_RX_PKT_15_0		0x802b
+#define QCA808X_MMD7_CNT_RX_ERR_PKT		0x802c
+#define QCA808X_MMD7_CNT_TX_PKT_31_16		0x802d
+#define QCA808X_MMD7_CNT_TX_PKT_15_0		0x802e
+#define QCA808X_MMD7_CNT_TX_ERR_PKT		0x802f
+
+enum stat_access_type {
+	PHY,
+	MMD
+};
+
+struct at803x_hw_stat {
+	const char *string;
+	u8 reg;
+	u32 mask;
+	enum stat_access_type access_type;
+};
+
+struct at803x_ss_mask {
+	u16 speed_mask;
+	u8 speed_shift;
+};
+
+struct qcom_phy_hw_stats {
+	u64 rx_pkts;
+	u64 rx_err_pkts;
+	u64 tx_pkts;
+	u64 tx_err_pkts;
+};
+
+int at803x_debug_reg_read(struct phy_device *phydev, u16 reg);
+int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
+			  u16 clear, u16 set);
+int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data);
+int at803x_set_wol(struct phy_device *phydev,
+		   struct ethtool_wolinfo *wol);
+int at8031_set_wol(struct phy_device *phydev,
+		   struct ethtool_wolinfo *wol);
+void at803x_get_wol(struct phy_device *phydev,
+		    struct ethtool_wolinfo *wol);
+int at803x_ack_interrupt(struct phy_device *phydev);
+int at803x_config_intr(struct phy_device *phydev);
+irqreturn_t at803x_handle_interrupt(struct phy_device *phydev);
+int at803x_read_specific_status(struct phy_device *phydev,
+				struct at803x_ss_mask ss_mask);
+int at803x_config_mdix(struct phy_device *phydev, u8 ctrl);
+int at803x_prepare_config_aneg(struct phy_device *phydev);
+int at803x_read_status(struct phy_device *phydev);
+int at803x_get_tunable(struct phy_device *phydev,
+		       struct ethtool_tunable *tuna, void *data);
+int at803x_set_tunable(struct phy_device *phydev,
+		       struct ethtool_tunable *tuna, const void *data);
+int at803x_cdt_fault_length(int dt);
+int at803x_cdt_start(struct phy_device *phydev, u32 cdt_start);
+int at803x_cdt_wait_for_completion(struct phy_device *phydev,
+				   u32 cdt_en);
+int qca808x_cable_test_get_status(struct phy_device *phydev, bool *finished);
+int qca808x_led_reg_hw_control_enable(struct phy_device *phydev, u16 reg);
+bool qca808x_led_reg_hw_control_status(struct phy_device *phydev, u16 reg);
+int qca808x_led_reg_brightness_set(struct phy_device *phydev,
+				   u16 reg, enum led_brightness value);
+int qca808x_led_reg_blink_set(struct phy_device *phydev, u16 reg,
+			      unsigned long *delay_on,
+			      unsigned long *delay_off);
+int qcom_phy_counter_config(struct phy_device *phydev);
+int qcom_phy_update_stats(struct phy_device *phydev,
+			  struct qcom_phy_hw_stats *hw_stats);
+void qcom_phy_get_stats(struct ethtool_phy_stats *stats,
+			struct qcom_phy_hw_stats hw_stats);