Resguardo inicial

linux-7.2.3/drivers/net/wireless/ath/ath5k/Kconfig

@@ -0,0 +1,73 @@
+# SPDX-License-Identifier: ISC
+config ATH5K
+	tristate "Atheros 5xxx wireless cards support"
+	depends on (PCI || ATH25) && MAC80211
+	select ATH_COMMON
+	select MAC80211_LEDS if LEDS_CLASS=y || LEDS_CLASS=MAC80211
+	select ATH5K_AHB if ATH25
+	select ATH5K_PCI if !ATH25
+	help
+	  This module adds support for wireless adapters based on
+	  Atheros 5xxx chipset.
+
+	  Currently the following chip versions are supported:
+
+	  MAC: AR5211 AR5212
+	  PHY: RF5111/2111 RF5112/2112 RF5413/2413
+
+	  This driver uses the kernel's mac80211 subsystem.
+
+	  If you choose to build a module, it'll be called ath5k. Say M if
+	  unsure.
+
+config ATH5K_DEBUG
+	bool "Atheros 5xxx debugging"
+	depends on ATH5K
+	help
+	  Atheros 5xxx debugging messages.
+
+	  Say Y, if and you will get debug options for ath5k.
+	  To use this, you need to mount debugfs:
+
+	  mount -t debugfs debug /sys/kernel/debug
+
+	  You will get access to files under:
+	  /sys/kernel/debug/ath5k/phy0/
+
+	  To enable debug, pass the debug level to the debug module
+	  parameter. For example:
+
+	  modprobe ath5k debug=0x00000400
+
+config ATH5K_TRACER
+	bool "Atheros 5xxx tracer"
+	depends on ATH5K
+	depends on EVENT_TRACING
+	help
+	  Say Y here to enable tracepoints for the ath5k driver
+	  using the kernel tracing infrastructure.  Select this
+	  option if you are interested in debugging the driver.
+
+	  If unsure, say N.
+
+config ATH5K_AHB
+	bool "Atheros 5xxx AHB bus support"
+	depends on ATH25 && ATH5K
+	help
+	  This adds support for WiSoC type chipsets of the 5xxx Atheros
+	  family.
+
+config ATH5K_PCI
+	bool "Atheros 5xxx PCI bus support"
+	depends on (!ATH25 && PCI)
+	help
+	  This adds support for PCI type chipsets of the 5xxx Atheros
+	  family.
+
+config ATH5K_TEST_CHANNELS
+	bool "Enables testing channels on ath5k"
+	depends on ATH5K && CFG80211_CERTIFICATION_ONUS
+	help
+	  This enables non-standard IEEE 802.11 channels on ath5k, which
+	  can be used for research purposes. This option should be disabled
+	  unless doing research.

linux-7.2.3/drivers/net/wireless/ath/ath5k/Makefile

@@ -0,0 +1,23 @@
+# SPDX-License-Identifier: ISC
+ath5k-y				+= caps.o
+ath5k-y				+= initvals.o
+ath5k-y				+= eeprom.o
+ath5k-y				+= gpio.o
+ath5k-y				+= desc.o
+ath5k-y				+= dma.o
+ath5k-y				+= qcu.o
+ath5k-y				+= pcu.o
+ath5k-y				+= phy.o
+ath5k-y				+= reset.o
+ath5k-y				+= attach.o
+ath5k-y				+= base.o
+CFLAGS_base.o			+= -I$(src)
+ath5k-y				+= led.o
+ath5k-y				+= rfkill.o
+ath5k-y				+= ani.o
+ath5k-y				+= sysfs.o
+ath5k-y				+= mac80211-ops.o
+ath5k-$(CONFIG_ATH5K_DEBUG)	+= debug.o
+ath5k-$(CONFIG_ATH5K_AHB)	+= ahb.o
+ath5k-$(CONFIG_ATH5K_PCI)	+= pci.o
+obj-$(CONFIG_ATH5K)		+= ath5k.o

linux-7.2.3/drivers/net/wireless/ath/ath5k/ahb.c

@@ -0,0 +1,228 @@
+/*
+ * Copyright (c) 2008-2009 Atheros Communications Inc.
+ * Copyright (c) 2009 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (c) 2009 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include <linux/module.h>
+#include <linux/nl80211.h>
+#include <linux/platform_device.h>
+#include <linux/etherdevice.h>
+#include <ath25_platform.h>
+#include "ath5k.h"
+#include "debug.h"
+#include "base.h"
+#include "reg.h"
+
+/* return bus cachesize in 4B word units */
+static void ath5k_ahb_read_cachesize(struct ath_common *common, int *csz)
+{
+	*csz = L1_CACHE_BYTES >> 2;
+}
+
+static bool
+ath5k_ahb_eeprom_read(struct ath_common *common, u32 off, u16 *data)
+{
+	struct ath5k_hw *ah = common->priv;
+	struct platform_device *pdev = to_platform_device(ah->dev);
+	struct ar231x_board_config *bcfg = dev_get_platdata(&pdev->dev);
+	u16 *eeprom, *eeprom_end;
+
+	eeprom = (u16 *) bcfg->radio;
+	eeprom_end = ((void *) bcfg->config) + BOARD_CONFIG_BUFSZ;
+
+	eeprom += off;
+	if (eeprom > eeprom_end)
+		return false;
+
+	*data = *eeprom;
+	return true;
+}
+
+int ath5k_hw_read_srev(struct ath5k_hw *ah)
+{
+	struct platform_device *pdev = to_platform_device(ah->dev);
+	struct ar231x_board_config *bcfg = dev_get_platdata(&pdev->dev);
+	ah->ah_mac_srev = bcfg->devid;
+	return 0;
+}
+
+static int ath5k_ahb_eeprom_read_mac(struct ath5k_hw *ah, u8 *mac)
+{
+	struct platform_device *pdev = to_platform_device(ah->dev);
+	struct ar231x_board_config *bcfg = dev_get_platdata(&pdev->dev);
+	u8 *cfg_mac;
+
+	if (to_platform_device(ah->dev)->id == 0)
+		cfg_mac = bcfg->config->wlan0_mac;
+	else
+		cfg_mac = bcfg->config->wlan1_mac;
+
+	memcpy(mac, cfg_mac, ETH_ALEN);
+	return 0;
+}
+
+static const struct ath_bus_ops ath_ahb_bus_ops = {
+	.ath_bus_type = ATH_AHB,
+	.read_cachesize = ath5k_ahb_read_cachesize,
+	.eeprom_read = ath5k_ahb_eeprom_read,
+	.eeprom_read_mac = ath5k_ahb_eeprom_read_mac,
+};
+
+/*Initialization*/
+static int ath_ahb_probe(struct platform_device *pdev)
+{
+	struct ar231x_board_config *bcfg = dev_get_platdata(&pdev->dev);
+	struct ath5k_hw *ah;
+	struct ieee80211_hw *hw;
+	struct resource *res;
+	void __iomem *mem;
+	int irq;
+	int ret = 0;
+	u32 reg;
+
+	if (!dev_get_platdata(&pdev->dev)) {
+		dev_err(&pdev->dev, "no platform data specified\n");
+		ret = -EINVAL;
+		goto err_out;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (res == NULL) {
+		dev_err(&pdev->dev, "no memory resource found\n");
+		ret = -ENXIO;
+		goto err_out;
+	}
+
+	mem = ioremap(res->start, resource_size(res));
+	if (mem == NULL) {
+		dev_err(&pdev->dev, "ioremap failed\n");
+		ret = -ENOMEM;
+		goto err_out;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		ret = irq;
+		goto err_iounmap;
+	}
+
+	hw = ieee80211_alloc_hw(sizeof(struct ath5k_hw), &ath5k_hw_ops);
+	if (hw == NULL) {
+		dev_err(&pdev->dev, "no memory for ieee80211_hw\n");
+		ret = -ENOMEM;
+		goto err_iounmap;
+	}
+
+	ah = hw->priv;
+	ah->hw = hw;
+	ah->dev = &pdev->dev;
+	ah->iobase = mem;
+	ah->irq = irq;
+	ah->devid = bcfg->devid;
+
+	if (bcfg->devid >= AR5K_SREV_AR2315_R6) {
+		/* Enable WMAC AHB arbitration */
+		reg = ioread32((void __iomem *) AR5K_AR2315_AHB_ARB_CTL);
+		reg |= AR5K_AR2315_AHB_ARB_CTL_WLAN;
+		iowrite32(reg, (void __iomem *) AR5K_AR2315_AHB_ARB_CTL);
+
+		/* Enable global WMAC swapping */
+		reg = ioread32((void __iomem *) AR5K_AR2315_BYTESWAP);
+		reg |= AR5K_AR2315_BYTESWAP_WMAC;
+		iowrite32(reg, (void __iomem *) AR5K_AR2315_BYTESWAP);
+	} else {
+		/* Enable WMAC DMA access (assuming 5312 or 231x*/
+		/* TODO: check other platforms */
+		reg = ioread32((void __iomem *) AR5K_AR5312_ENABLE);
+		if (to_platform_device(ah->dev)->id == 0)
+			reg |= AR5K_AR5312_ENABLE_WLAN0;
+		else
+			reg |= AR5K_AR5312_ENABLE_WLAN1;
+		iowrite32(reg, (void __iomem *) AR5K_AR5312_ENABLE);
+
+		/*
+		 * On a dual-band AR5312, the multiband radio is only
+		 * used as pass-through. Disable 2 GHz support in the
+		 * driver for it
+		 */
+		if (to_platform_device(ah->dev)->id == 0 &&
+		    (bcfg->config->flags & (BD_WLAN0 | BD_WLAN1)) ==
+		     (BD_WLAN1 | BD_WLAN0))
+			ah->ah_capabilities.cap_needs_2GHz_ovr = true;
+		else
+			ah->ah_capabilities.cap_needs_2GHz_ovr = false;
+	}
+
+	ret = ath5k_init_ah(ah, &ath_ahb_bus_ops);
+	if (ret != 0) {
+		dev_err(&pdev->dev, "failed to attach device, err=%d\n", ret);
+		ret = -ENODEV;
+		goto err_free_hw;
+	}
+
+	platform_set_drvdata(pdev, hw);
+
+	return 0;
+
+ err_free_hw:
+	ieee80211_free_hw(hw);
+ err_iounmap:
+        iounmap(mem);
+ err_out:
+	return ret;
+}
+
+static void ath_ahb_remove(struct platform_device *pdev)
+{
+	struct ar231x_board_config *bcfg = dev_get_platdata(&pdev->dev);
+	struct ieee80211_hw *hw = platform_get_drvdata(pdev);
+	struct ath5k_hw *ah;
+	u32 reg;
+
+	if (!hw)
+		return;
+
+	ah = hw->priv;
+
+	if (bcfg->devid >= AR5K_SREV_AR2315_R6) {
+		/* Disable WMAC AHB arbitration */
+		reg = ioread32((void __iomem *) AR5K_AR2315_AHB_ARB_CTL);
+		reg &= ~AR5K_AR2315_AHB_ARB_CTL_WLAN;
+		iowrite32(reg, (void __iomem *) AR5K_AR2315_AHB_ARB_CTL);
+	} else {
+		/*Stop DMA access */
+		reg = ioread32((void __iomem *) AR5K_AR5312_ENABLE);
+		if (to_platform_device(ah->dev)->id == 0)
+			reg &= ~AR5K_AR5312_ENABLE_WLAN0;
+		else
+			reg &= ~AR5K_AR5312_ENABLE_WLAN1;
+		iowrite32(reg, (void __iomem *) AR5K_AR5312_ENABLE);
+	}
+
+	ath5k_deinit_ah(ah);
+	iounmap(ah->iobase);
+	ieee80211_free_hw(hw);
+}
+
+static struct platform_driver ath_ahb_driver = {
+	.probe = ath_ahb_probe,
+	.remove = ath_ahb_remove,
+	.driver = {
+		.name = "ar231x-wmac",
+	},
+};
+
+module_platform_driver(ath_ahb_driver);

linux-7.2.3/drivers/net/wireless/ath/ath5k/ani.c

@@ -0,0 +1,754 @@
+/*
+ * Copyright (C) 2010 Bruno Randolf <br1@einfach.org>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include "ath5k.h"
+#include "reg.h"
+#include "debug.h"
+#include "ani.h"
+
+/**
+ * DOC: Basic ANI Operation
+ *
+ * Adaptive Noise Immunity (ANI) controls five noise immunity parameters
+ * depending on the amount of interference in the environment, increasing
+ * or reducing sensitivity as necessary.
+ *
+ * The parameters are:
+ *
+ *   - "noise immunity"
+ *
+ *   - "spur immunity"
+ *
+ *   - "firstep level"
+ *
+ *   - "OFDM weak signal detection"
+ *
+ *   - "CCK weak signal detection"
+ *
+ * Basically we look at the amount of ODFM and CCK timing errors we get and then
+ * raise or lower immunity accordingly by setting one or more of these
+ * parameters.
+ *
+ * Newer chipsets have PHY error counters in hardware which will generate a MIB
+ * interrupt when they overflow. Older hardware has too enable PHY error frames
+ * by setting a RX flag and then count every single PHY error. When a specified
+ * threshold of errors has been reached we will raise immunity.
+ * Also we regularly check the amount of errors and lower or raise immunity as
+ * necessary.
+ */
+
+
+/***********************\
+* ANI parameter control *
+\***********************/
+
+/**
+ * ath5k_ani_set_noise_immunity_level() - Set noise immunity level
+ * @ah: The &struct ath5k_hw
+ * @level: level between 0 and @ATH5K_ANI_MAX_NOISE_IMM_LVL
+ */
+void
+ath5k_ani_set_noise_immunity_level(struct ath5k_hw *ah, int level)
+{
+	/* TODO:
+	 * ANI documents suggest the following five levels to use, but the HAL
+	 * and ath9k use only the last two levels, making this
+	 * essentially an on/off option. There *may* be a reason for this (???),
+	 * so i stick with the HAL version for now...
+	 */
+#if 0
+	static const s8 lo[] = { -52, -56, -60, -64, -70 };
+	static const s8 hi[] = { -18, -18, -16, -14, -12 };
+	static const s8 sz[] = { -34, -41, -48, -55, -62 };
+	static const s8 fr[] = { -70, -72, -75, -78, -80 };
+#else
+	static const s8 lo[] = { -64, -70 };
+	static const s8 hi[] = { -14, -12 };
+	static const s8 sz[] = { -55, -62 };
+	static const s8 fr[] = { -78, -80 };
+#endif
+	if (level < 0 || level >= ARRAY_SIZE(sz)) {
+		ATH5K_ERR(ah, "noise immunity level %d out of range",
+			  level);
+		return;
+	}
+
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_DESIRED_SIZE,
+				AR5K_PHY_DESIRED_SIZE_TOT, sz[level]);
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_AGCCOARSE,
+				AR5K_PHY_AGCCOARSE_LO, lo[level]);
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_AGCCOARSE,
+				AR5K_PHY_AGCCOARSE_HI, hi[level]);
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_SIG,
+				AR5K_PHY_SIG_FIRPWR, fr[level]);
+
+	ah->ani_state.noise_imm_level = level;
+	ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI, "new level %d", level);
+}
+
+/**
+ * ath5k_ani_set_spur_immunity_level() - Set spur immunity level
+ * @ah: The &struct ath5k_hw
+ * @level: level between 0 and @max_spur_level (the maximum level is dependent
+ * on the chip revision).
+ */
+void
+ath5k_ani_set_spur_immunity_level(struct ath5k_hw *ah, int level)
+{
+	static const int val[] = { 2, 4, 6, 8, 10, 12, 14, 16 };
+
+	if (level < 0 || level >= ARRAY_SIZE(val) ||
+	    level > ah->ani_state.max_spur_level) {
+		ATH5K_ERR(ah, "spur immunity level %d out of range",
+			  level);
+		return;
+	}
+
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_OFDM_SELFCORR,
+		AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1, val[level]);
+
+	ah->ani_state.spur_level = level;
+	ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI, "new level %d", level);
+}
+
+/**
+ * ath5k_ani_set_firstep_level() - Set "firstep" level
+ * @ah: The &struct ath5k_hw
+ * @level: level between 0 and @ATH5K_ANI_MAX_FIRSTEP_LVL
+ */
+void
+ath5k_ani_set_firstep_level(struct ath5k_hw *ah, int level)
+{
+	static const int val[] = { 0, 4, 8 };
+
+	if (level < 0 || level >= ARRAY_SIZE(val)) {
+		ATH5K_ERR(ah, "firstep level %d out of range", level);
+		return;
+	}
+
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_SIG,
+				AR5K_PHY_SIG_FIRSTEP, val[level]);
+
+	ah->ani_state.firstep_level = level;
+	ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI, "new level %d", level);
+}
+
+/**
+ * ath5k_ani_set_ofdm_weak_signal_detection() - Set OFDM weak signal detection
+ * @ah: The &struct ath5k_hw
+ * @on: turn on or off
+ */
+void
+ath5k_ani_set_ofdm_weak_signal_detection(struct ath5k_hw *ah, bool on)
+{
+	static const int m1l[] = { 127, 50 };
+	static const int m2l[] = { 127, 40 };
+	static const int m1[] = { 127, 0x4d };
+	static const int m2[] = { 127, 0x40 };
+	static const int m2cnt[] = { 31, 16 };
+	static const int m2lcnt[] = { 63, 48 };
+
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_WEAK_OFDM_LOW_THR,
+				AR5K_PHY_WEAK_OFDM_LOW_THR_M1, m1l[on]);
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_WEAK_OFDM_LOW_THR,
+				AR5K_PHY_WEAK_OFDM_LOW_THR_M2, m2l[on]);
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_WEAK_OFDM_HIGH_THR,
+				AR5K_PHY_WEAK_OFDM_HIGH_THR_M1, m1[on]);
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_WEAK_OFDM_HIGH_THR,
+				AR5K_PHY_WEAK_OFDM_HIGH_THR_M2, m2[on]);
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_WEAK_OFDM_HIGH_THR,
+			AR5K_PHY_WEAK_OFDM_HIGH_THR_M2_COUNT, m2cnt[on]);
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_WEAK_OFDM_LOW_THR,
+			AR5K_PHY_WEAK_OFDM_LOW_THR_M2_COUNT, m2lcnt[on]);
+
+	if (on)
+		AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_WEAK_OFDM_LOW_THR,
+				AR5K_PHY_WEAK_OFDM_LOW_THR_SELFCOR_EN);
+	else
+		AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_WEAK_OFDM_LOW_THR,
+				AR5K_PHY_WEAK_OFDM_LOW_THR_SELFCOR_EN);
+
+	ah->ani_state.ofdm_weak_sig = on;
+	ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI, "turned %s",
+			  on ? "on" : "off");
+}
+
+/**
+ * ath5k_ani_set_cck_weak_signal_detection() - Set CCK weak signal detection
+ * @ah: The &struct ath5k_hw
+ * @on: turn on or off
+ */
+void
+ath5k_ani_set_cck_weak_signal_detection(struct ath5k_hw *ah, bool on)
+{
+	static const int val[] = { 8, 6 };
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_CCK_CROSSCORR,
+				AR5K_PHY_CCK_CROSSCORR_WEAK_SIG_THR, val[on]);
+	ah->ani_state.cck_weak_sig = on;
+	ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI, "turned %s",
+			  on ? "on" : "off");
+}
+
+
+/***************\
+* ANI algorithm *
+\***************/
+
+/**
+ * ath5k_ani_raise_immunity() - Increase noise immunity
+ * @ah: The &struct ath5k_hw
+ * @as: The &struct ath5k_ani_state
+ * @ofdm_trigger: If this is true we are called because of too many OFDM errors,
+ * the algorithm will tune more parameters then.
+ *
+ * Try to raise noise immunity (=decrease sensitivity) in several steps
+ * depending on the average RSSI of the beacons we received.
+ */
+static void
+ath5k_ani_raise_immunity(struct ath5k_hw *ah, struct ath5k_ani_state *as,
+			 bool ofdm_trigger)
+{
+	int rssi = ewma_beacon_rssi_read(&ah->ah_beacon_rssi_avg);
+
+	ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI, "raise immunity (%s)",
+		ofdm_trigger ? "ODFM" : "CCK");
+
+	/* first: raise noise immunity */
+	if (as->noise_imm_level < ATH5K_ANI_MAX_NOISE_IMM_LVL) {
+		ath5k_ani_set_noise_immunity_level(ah, as->noise_imm_level + 1);
+		return;
+	}
+
+	/* only OFDM: raise spur immunity level */
+	if (ofdm_trigger &&
+	    as->spur_level < ah->ani_state.max_spur_level) {
+		ath5k_ani_set_spur_immunity_level(ah, as->spur_level + 1);
+		return;
+	}
+
+	/* AP mode */
+	if (ah->opmode == NL80211_IFTYPE_AP) {
+		if (as->firstep_level < ATH5K_ANI_MAX_FIRSTEP_LVL)
+			ath5k_ani_set_firstep_level(ah, as->firstep_level + 1);
+		return;
+	}
+
+	/* STA and IBSS mode */
+
+	/* TODO: for IBSS mode it would be better to keep a beacon RSSI average
+	 * per each neighbour node and use the minimum of these, to make sure we
+	 * don't shut out a remote node by raising immunity too high. */
+
+	if (rssi > ATH5K_ANI_RSSI_THR_HIGH) {
+		ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI,
+				  "beacon RSSI high");
+		/* only OFDM: beacon RSSI is high, we can disable ODFM weak
+		 * signal detection */
+		if (ofdm_trigger && as->ofdm_weak_sig) {
+			ath5k_ani_set_ofdm_weak_signal_detection(ah, false);
+			ath5k_ani_set_spur_immunity_level(ah, 0);
+			return;
+		}
+		/* as a last resort or CCK: raise firstep level */
+		if (as->firstep_level < ATH5K_ANI_MAX_FIRSTEP_LVL) {
+			ath5k_ani_set_firstep_level(ah, as->firstep_level + 1);
+			return;
+		}
+	} else if (rssi > ATH5K_ANI_RSSI_THR_LOW) {
+		/* beacon RSSI in mid range, we need OFDM weak signal detect,
+		 * but can raise firstep level */
+		ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI,
+				  "beacon RSSI mid");
+		if (ofdm_trigger && !as->ofdm_weak_sig)
+			ath5k_ani_set_ofdm_weak_signal_detection(ah, true);
+		if (as->firstep_level < ATH5K_ANI_MAX_FIRSTEP_LVL)
+			ath5k_ani_set_firstep_level(ah, as->firstep_level + 1);
+		return;
+	} else if (ah->ah_current_channel->band == NL80211_BAND_2GHZ) {
+		/* beacon RSSI is low. in B/G mode turn of OFDM weak signal
+		 * detect and zero firstep level to maximize CCK sensitivity */
+		ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI,
+				  "beacon RSSI low, 2GHz");
+		if (ofdm_trigger && as->ofdm_weak_sig)
+			ath5k_ani_set_ofdm_weak_signal_detection(ah, false);
+		if (as->firstep_level > 0)
+			ath5k_ani_set_firstep_level(ah, 0);
+		return;
+	}
+
+	/* TODO: why not?:
+	if (as->cck_weak_sig == true) {
+		ath5k_ani_set_cck_weak_signal_detection(ah, false);
+	}
+	*/
+}
+
+/**
+ * ath5k_ani_lower_immunity() - Decrease noise immunity
+ * @ah: The &struct ath5k_hw
+ * @as: The &struct ath5k_ani_state
+ *
+ * Try to lower noise immunity (=increase sensitivity) in several steps
+ * depending on the average RSSI of the beacons we received.
+ */
+static void
+ath5k_ani_lower_immunity(struct ath5k_hw *ah, struct ath5k_ani_state *as)
+{
+	int rssi = ewma_beacon_rssi_read(&ah->ah_beacon_rssi_avg);
+
+	ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI, "lower immunity");
+
+	if (ah->opmode == NL80211_IFTYPE_AP) {
+		/* AP mode */
+		if (as->firstep_level > 0) {
+			ath5k_ani_set_firstep_level(ah, as->firstep_level - 1);
+			return;
+		}
+	} else {
+		/* STA and IBSS mode (see TODO above) */
+		if (rssi > ATH5K_ANI_RSSI_THR_HIGH) {
+			/* beacon signal is high, leave OFDM weak signal
+			 * detection off or it may oscillate
+			 * TODO: who said it's off??? */
+		} else if (rssi > ATH5K_ANI_RSSI_THR_LOW) {
+			/* beacon RSSI is mid-range: turn on ODFM weak signal
+			 * detection and next, lower firstep level */
+			if (!as->ofdm_weak_sig) {
+				ath5k_ani_set_ofdm_weak_signal_detection(ah,
+									 true);
+				return;
+			}
+			if (as->firstep_level > 0) {
+				ath5k_ani_set_firstep_level(ah,
+							as->firstep_level - 1);
+				return;
+			}
+		} else {
+			/* beacon signal is low: only reduce firstep level */
+			if (as->firstep_level > 0) {
+				ath5k_ani_set_firstep_level(ah,
+							as->firstep_level - 1);
+				return;
+			}
+		}
+	}
+
+	/* all modes */
+	if (as->spur_level > 0) {
+		ath5k_ani_set_spur_immunity_level(ah, as->spur_level - 1);
+		return;
+	}
+
+	/* finally, reduce noise immunity */
+	if (as->noise_imm_level > 0) {
+		ath5k_ani_set_noise_immunity_level(ah, as->noise_imm_level - 1);
+		return;
+	}
+}
+
+/**
+ * ath5k_hw_ani_get_listen_time() - Update counters and return listening time
+ * @ah: The &struct ath5k_hw
+ * @as: The &struct ath5k_ani_state
+ *
+ * Return an approximation of the time spent "listening" in milliseconds (ms)
+ * since the last call of this function.
+ * Save a snapshot of the counter values for debugging/statistics.
+ */
+static int
+ath5k_hw_ani_get_listen_time(struct ath5k_hw *ah, struct ath5k_ani_state *as)
+{
+	struct ath_common *common = ath5k_hw_common(ah);
+	int listen;
+
+	spin_lock_bh(&common->cc_lock);
+
+	ath_hw_cycle_counters_update(common);
+	memcpy(&as->last_cc, &common->cc_ani, sizeof(as->last_cc));
+
+	/* clears common->cc_ani */
+	listen = ath_hw_get_listen_time(common);
+
+	spin_unlock_bh(&common->cc_lock);
+
+	return listen;
+}
+
+/**
+ * ath5k_ani_save_and_clear_phy_errors() - Clear and save PHY error counters
+ * @ah: The &struct ath5k_hw
+ * @as: The &struct ath5k_ani_state
+ *
+ * Clear the PHY error counters as soon as possible, since this might be called
+ * from a MIB interrupt and we want to make sure we don't get interrupted again.
+ * Add the count of CCK and OFDM errors to our internal state, so it can be used
+ * by the algorithm later.
+ *
+ * Will be called from interrupt and tasklet context.
+ * Returns 0 if both counters are zero.
+ */
+static int
+ath5k_ani_save_and_clear_phy_errors(struct ath5k_hw *ah,
+				    struct ath5k_ani_state *as)
+{
+	unsigned int ofdm_err, cck_err;
+
+	if (!ah->ah_capabilities.cap_has_phyerr_counters)
+		return 0;
+
+	ofdm_err = ath5k_hw_reg_read(ah, AR5K_PHYERR_CNT1);
+	cck_err = ath5k_hw_reg_read(ah, AR5K_PHYERR_CNT2);
+
+	/* reset counters first, we might be in a hurry (interrupt) */
+	ath5k_hw_reg_write(ah, ATH5K_PHYERR_CNT_MAX - ATH5K_ANI_OFDM_TRIG_HIGH,
+			   AR5K_PHYERR_CNT1);
+	ath5k_hw_reg_write(ah, ATH5K_PHYERR_CNT_MAX - ATH5K_ANI_CCK_TRIG_HIGH,
+			   AR5K_PHYERR_CNT2);
+
+	ofdm_err = ATH5K_ANI_OFDM_TRIG_HIGH - (ATH5K_PHYERR_CNT_MAX - ofdm_err);
+	cck_err = ATH5K_ANI_CCK_TRIG_HIGH - (ATH5K_PHYERR_CNT_MAX - cck_err);
+
+	/* sometimes both can be zero, especially when there is a superfluous
+	 * second interrupt. detect that here and return an error. */
+	if (ofdm_err <= 0 && cck_err <= 0)
+		return 0;
+
+	/* avoid negative values should one of the registers overflow */
+	if (ofdm_err > 0) {
+		as->ofdm_errors += ofdm_err;
+		as->sum_ofdm_errors += ofdm_err;
+	}
+	if (cck_err > 0) {
+		as->cck_errors += cck_err;
+		as->sum_cck_errors += cck_err;
+	}
+	return 1;
+}
+
+/**
+ * ath5k_ani_period_restart() - Restart ANI period
+ * @as: The &struct ath5k_ani_state
+ *
+ * Just reset counters, so they are clear for the next "ani period".
+ */
+static void
+ath5k_ani_period_restart(struct ath5k_ani_state *as)
+{
+	/* keep last values for debugging */
+	as->last_ofdm_errors = as->ofdm_errors;
+	as->last_cck_errors = as->cck_errors;
+	as->last_listen = as->listen_time;
+
+	as->ofdm_errors = 0;
+	as->cck_errors = 0;
+	as->listen_time = 0;
+}
+
+/**
+ * ath5k_ani_calibration() - The main ANI calibration function
+ * @ah: The &struct ath5k_hw
+ *
+ * We count OFDM and CCK errors relative to the time where we did not send or
+ * receive ("listen" time) and raise or lower immunity accordingly.
+ * This is called regularly (every second) from the calibration timer, but also
+ * when an error threshold has been reached.
+ *
+ * In order to synchronize access from different contexts, this should be
+ * called only indirectly by scheduling the ANI tasklet!
+ */
+void
+ath5k_ani_calibration(struct ath5k_hw *ah)
+{
+	struct ath5k_ani_state *as = &ah->ani_state;
+	int listen, ofdm_high, ofdm_low, cck_high, cck_low;
+
+	/* get listen time since last call and add it to the counter because we
+	 * might not have restarted the "ani period" last time.
+	 * always do this to calculate the busy time also in manual mode */
+	listen = ath5k_hw_ani_get_listen_time(ah, as);
+	as->listen_time += listen;
+
+	if (as->ani_mode != ATH5K_ANI_MODE_AUTO)
+		return;
+
+	ath5k_ani_save_and_clear_phy_errors(ah, as);
+
+	ofdm_high = as->listen_time * ATH5K_ANI_OFDM_TRIG_HIGH / 1000;
+	cck_high = as->listen_time * ATH5K_ANI_CCK_TRIG_HIGH / 1000;
+	ofdm_low = as->listen_time * ATH5K_ANI_OFDM_TRIG_LOW / 1000;
+	cck_low = as->listen_time * ATH5K_ANI_CCK_TRIG_LOW / 1000;
+
+	ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI,
+		"listen %d (now %d)", as->listen_time, listen);
+	ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI,
+		"check high ofdm %d/%d cck %d/%d",
+		as->ofdm_errors, ofdm_high, as->cck_errors, cck_high);
+
+	if (as->ofdm_errors > ofdm_high || as->cck_errors > cck_high) {
+		/* too many PHY errors - we have to raise immunity */
+		bool ofdm_flag = as->ofdm_errors > ofdm_high;
+		ath5k_ani_raise_immunity(ah, as, ofdm_flag);
+		ath5k_ani_period_restart(as);
+
+	} else if (as->listen_time > 5 * ATH5K_ANI_LISTEN_PERIOD) {
+		/* If more than 5 (TODO: why 5?) periods have passed and we got
+		 * relatively little errors we can try to lower immunity */
+		ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI,
+			"check low ofdm %d/%d cck %d/%d",
+			as->ofdm_errors, ofdm_low, as->cck_errors, cck_low);
+
+		if (as->ofdm_errors <= ofdm_low && as->cck_errors <= cck_low)
+			ath5k_ani_lower_immunity(ah, as);
+
+		ath5k_ani_period_restart(as);
+	}
+}
+
+
+/*******************\
+* Interrupt handler *
+\*******************/
+
+/**
+ * ath5k_ani_mib_intr() - Interrupt handler for ANI MIB counters
+ * @ah: The &struct ath5k_hw
+ *
+ * Just read & reset the registers quickly, so they don't generate more
+ * interrupts, save the counters and schedule the tasklet to decide whether
+ * to raise immunity or not.
+ *
+ * We just need to handle PHY error counters, ath5k_hw_update_mib_counters()
+ * should take care of all "normal" MIB interrupts.
+ */
+void
+ath5k_ani_mib_intr(struct ath5k_hw *ah)
+{
+	struct ath5k_ani_state *as = &ah->ani_state;
+
+	/* nothing to do here if HW does not have PHY error counters - they
+	 * can't be the reason for the MIB interrupt then */
+	if (!ah->ah_capabilities.cap_has_phyerr_counters)
+		return;
+
+	/* not in use but clear anyways */
+	ath5k_hw_reg_write(ah, 0, AR5K_OFDM_FIL_CNT);
+	ath5k_hw_reg_write(ah, 0, AR5K_CCK_FIL_CNT);
+
+	if (ah->ani_state.ani_mode != ATH5K_ANI_MODE_AUTO)
+		return;
+
+	/* If one of the errors triggered, we can get a superfluous second
+	 * interrupt, even though we have already reset the register. The
+	 * function detects that so we can return early. */
+	if (ath5k_ani_save_and_clear_phy_errors(ah, as) == 0)
+		return;
+
+	if (as->ofdm_errors > ATH5K_ANI_OFDM_TRIG_HIGH ||
+	    as->cck_errors > ATH5K_ANI_CCK_TRIG_HIGH)
+		tasklet_schedule(&ah->ani_tasklet);
+}
+
+/**
+ * ath5k_ani_phy_error_report - Used by older HW to report PHY errors
+ *
+ * @ah: The &struct ath5k_hw
+ * @phyerr: One of enum ath5k_phy_error_code
+ *
+ * This is used by hardware without PHY error counters to report PHY errors
+ * on a frame-by-frame basis, instead of the interrupt.
+ */
+void
+ath5k_ani_phy_error_report(struct ath5k_hw *ah,
+			   enum ath5k_phy_error_code phyerr)
+{
+	struct ath5k_ani_state *as = &ah->ani_state;
+
+	if (phyerr == AR5K_RX_PHY_ERROR_OFDM_TIMING) {
+		as->ofdm_errors++;
+		if (as->ofdm_errors > ATH5K_ANI_OFDM_TRIG_HIGH)
+			tasklet_schedule(&ah->ani_tasklet);
+	} else if (phyerr == AR5K_RX_PHY_ERROR_CCK_TIMING) {
+		as->cck_errors++;
+		if (as->cck_errors > ATH5K_ANI_CCK_TRIG_HIGH)
+			tasklet_schedule(&ah->ani_tasklet);
+	}
+}
+
+
+/****************\
+* Initialization *
+\****************/
+
+/**
+ * ath5k_enable_phy_err_counters() - Enable PHY error counters
+ * @ah: The &struct ath5k_hw
+ *
+ * Enable PHY error counters for OFDM and CCK timing errors.
+ */
+static void
+ath5k_enable_phy_err_counters(struct ath5k_hw *ah)
+{
+	ath5k_hw_reg_write(ah, ATH5K_PHYERR_CNT_MAX - ATH5K_ANI_OFDM_TRIG_HIGH,
+			   AR5K_PHYERR_CNT1);
+	ath5k_hw_reg_write(ah, ATH5K_PHYERR_CNT_MAX - ATH5K_ANI_CCK_TRIG_HIGH,
+			   AR5K_PHYERR_CNT2);
+	ath5k_hw_reg_write(ah, AR5K_PHY_ERR_FIL_OFDM, AR5K_PHYERR_CNT1_MASK);
+	ath5k_hw_reg_write(ah, AR5K_PHY_ERR_FIL_CCK, AR5K_PHYERR_CNT2_MASK);
+
+	/* not in use */
+	ath5k_hw_reg_write(ah, 0, AR5K_OFDM_FIL_CNT);
+	ath5k_hw_reg_write(ah, 0, AR5K_CCK_FIL_CNT);
+}
+
+/**
+ * ath5k_disable_phy_err_counters() - Disable PHY error counters
+ * @ah: The &struct ath5k_hw
+ *
+ * Disable PHY error counters for OFDM and CCK timing errors.
+ */
+static void
+ath5k_disable_phy_err_counters(struct ath5k_hw *ah)
+{
+	ath5k_hw_reg_write(ah, 0, AR5K_PHYERR_CNT1);
+	ath5k_hw_reg_write(ah, 0, AR5K_PHYERR_CNT2);
+	ath5k_hw_reg_write(ah, 0, AR5K_PHYERR_CNT1_MASK);
+	ath5k_hw_reg_write(ah, 0, AR5K_PHYERR_CNT2_MASK);
+
+	/* not in use */
+	ath5k_hw_reg_write(ah, 0, AR5K_OFDM_FIL_CNT);
+	ath5k_hw_reg_write(ah, 0, AR5K_CCK_FIL_CNT);
+}
+
+/**
+ * ath5k_ani_init() - Initialize ANI
+ * @ah: The &struct ath5k_hw
+ * @mode: One of enum ath5k_ani_mode
+ *
+ * Initialize ANI according to mode.
+ */
+void
+ath5k_ani_init(struct ath5k_hw *ah, enum ath5k_ani_mode mode)
+{
+	/* ANI is only possible on 5212 and newer */
+	if (ah->ah_version < AR5K_AR5212)
+		return;
+
+	if (mode < ATH5K_ANI_MODE_OFF || mode > ATH5K_ANI_MODE_AUTO) {
+		ATH5K_ERR(ah, "ANI mode %d out of range", mode);
+		return;
+	}
+
+	/* clear old state information */
+	memset(&ah->ani_state, 0, sizeof(ah->ani_state));
+
+	/* older hardware has more spur levels than newer */
+	if (ah->ah_mac_srev < AR5K_SREV_AR2414)
+		ah->ani_state.max_spur_level = 7;
+	else
+		ah->ani_state.max_spur_level = 2;
+
+	/* initial values for our ani parameters */
+	if (mode == ATH5K_ANI_MODE_OFF) {
+		ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI, "ANI off\n");
+	} else if (mode == ATH5K_ANI_MODE_MANUAL_LOW) {
+		ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI,
+			"ANI manual low -> high sensitivity\n");
+		ath5k_ani_set_noise_immunity_level(ah, 0);
+		ath5k_ani_set_spur_immunity_level(ah, 0);
+		ath5k_ani_set_firstep_level(ah, 0);
+		ath5k_ani_set_ofdm_weak_signal_detection(ah, true);
+		ath5k_ani_set_cck_weak_signal_detection(ah, true);
+	} else if (mode == ATH5K_ANI_MODE_MANUAL_HIGH) {
+		ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI,
+			"ANI manual high -> low sensitivity\n");
+		ath5k_ani_set_noise_immunity_level(ah,
+					ATH5K_ANI_MAX_NOISE_IMM_LVL);
+		ath5k_ani_set_spur_immunity_level(ah,
+					ah->ani_state.max_spur_level);
+		ath5k_ani_set_firstep_level(ah, ATH5K_ANI_MAX_FIRSTEP_LVL);
+		ath5k_ani_set_ofdm_weak_signal_detection(ah, false);
+		ath5k_ani_set_cck_weak_signal_detection(ah, false);
+	} else if (mode == ATH5K_ANI_MODE_AUTO) {
+		ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_ANI, "ANI auto\n");
+		ath5k_ani_set_noise_immunity_level(ah, 0);
+		ath5k_ani_set_spur_immunity_level(ah, 0);
+		ath5k_ani_set_firstep_level(ah, 0);
+		ath5k_ani_set_ofdm_weak_signal_detection(ah, true);
+		ath5k_ani_set_cck_weak_signal_detection(ah, false);
+	}
+
+	/* newer hardware has PHY error counter registers which we can use to
+	 * get OFDM and CCK error counts. older hardware has to set rxfilter and
+	 * report every single PHY error by calling ath5k_ani_phy_error_report()
+	 */
+	if (mode == ATH5K_ANI_MODE_AUTO) {
+		if (ah->ah_capabilities.cap_has_phyerr_counters)
+			ath5k_enable_phy_err_counters(ah);
+		else
+			ath5k_hw_set_rx_filter(ah, ath5k_hw_get_rx_filter(ah) |
+						   AR5K_RX_FILTER_PHYERR);
+	} else {
+		if (ah->ah_capabilities.cap_has_phyerr_counters)
+			ath5k_disable_phy_err_counters(ah);
+		else
+			ath5k_hw_set_rx_filter(ah, ath5k_hw_get_rx_filter(ah) &
+						   ~AR5K_RX_FILTER_PHYERR);
+	}
+
+	ah->ani_state.ani_mode = mode;
+}
+
+
+/**************\
+* Debug output *
+\**************/
+
+#ifdef CONFIG_ATH5K_DEBUG
+
+/**
+ * ath5k_ani_print_counters() - Print ANI counters
+ * @ah: The &struct ath5k_hw
+ *
+ * Used for debugging ANI
+ */
+void
+ath5k_ani_print_counters(struct ath5k_hw *ah)
+{
+	/* clears too */
+	pr_notice("ACK fail\t%d\n", ath5k_hw_reg_read(ah, AR5K_ACK_FAIL));
+	pr_notice("RTS fail\t%d\n", ath5k_hw_reg_read(ah, AR5K_RTS_FAIL));
+	pr_notice("RTS success\t%d\n", ath5k_hw_reg_read(ah, AR5K_RTS_OK));
+	pr_notice("FCS error\t%d\n", ath5k_hw_reg_read(ah, AR5K_FCS_FAIL));
+
+	/* no clear */
+	pr_notice("tx\t%d\n", ath5k_hw_reg_read(ah, AR5K_PROFCNT_TX));
+	pr_notice("rx\t%d\n", ath5k_hw_reg_read(ah, AR5K_PROFCNT_RX));
+	pr_notice("busy\t%d\n", ath5k_hw_reg_read(ah, AR5K_PROFCNT_RXCLR));
+	pr_notice("cycles\t%d\n", ath5k_hw_reg_read(ah, AR5K_PROFCNT_CYCLE));
+
+	pr_notice("AR5K_PHYERR_CNT1\t%d\n",
+		  ath5k_hw_reg_read(ah, AR5K_PHYERR_CNT1));
+	pr_notice("AR5K_PHYERR_CNT2\t%d\n",
+		  ath5k_hw_reg_read(ah, AR5K_PHYERR_CNT2));
+	pr_notice("AR5K_OFDM_FIL_CNT\t%d\n",
+		  ath5k_hw_reg_read(ah, AR5K_OFDM_FIL_CNT));
+	pr_notice("AR5K_CCK_FIL_CNT\t%d\n",
+		  ath5k_hw_reg_read(ah, AR5K_CCK_FIL_CNT));
+}
+
+#endif

linux-7.2.3/drivers/net/wireless/ath/ath5k/ani.h

@@ -0,0 +1,119 @@
+/*
+ * Copyright (C) 2010 Bruno Randolf <br1@einfach.org>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+#ifndef ANI_H
+#define ANI_H
+
+#include "../ath.h"
+
+enum ath5k_phy_error_code;
+
+/* these thresholds are relative to the ATH5K_ANI_LISTEN_PERIOD */
+#define ATH5K_ANI_LISTEN_PERIOD		100
+#define ATH5K_ANI_OFDM_TRIG_HIGH	500
+#define ATH5K_ANI_OFDM_TRIG_LOW		200
+#define ATH5K_ANI_CCK_TRIG_HIGH		200
+#define ATH5K_ANI_CCK_TRIG_LOW		100
+
+/* average beacon RSSI thresholds */
+#define ATH5K_ANI_RSSI_THR_HIGH		40
+#define ATH5K_ANI_RSSI_THR_LOW		7
+
+/* maximum available levels */
+#define ATH5K_ANI_MAX_FIRSTEP_LVL	2
+#define ATH5K_ANI_MAX_NOISE_IMM_LVL	1
+
+
+/**
+ * enum ath5k_ani_mode - mode for ANI / noise sensitivity
+ *
+ * @ATH5K_ANI_MODE_OFF: Turn ANI off. This can be useful to just stop the ANI
+ *			algorithm after it has been on auto mode.
+ * @ATH5K_ANI_MODE_MANUAL_LOW: Manually set all immunity parameters to low,
+ *			maximizing sensitivity. ANI will not run.
+ * @ATH5K_ANI_MODE_MANUAL_HIGH: Manually set all immunity parameters to high,
+ *			minimizing sensitivity. ANI will not run.
+ * @ATH5K_ANI_MODE_AUTO: Automatically control immunity parameters based on the
+ *			amount of OFDM and CCK frame errors (default).
+ */
+enum ath5k_ani_mode {
+	ATH5K_ANI_MODE_OFF		= 0,
+	ATH5K_ANI_MODE_MANUAL_LOW	= 1,
+	ATH5K_ANI_MODE_MANUAL_HIGH	= 2,
+	ATH5K_ANI_MODE_AUTO		= 3
+};
+
+
+/**
+ * struct ath5k_ani_state - ANI state and associated counters
+ * @ani_mode: One of enum ath5k_ani_mode
+ * @noise_imm_level: Noise immunity level
+ * @spur_level: Spur immunity level
+ * @firstep_level: FIRstep level
+ * @ofdm_weak_sig: OFDM weak signal detection state (on/off)
+ * @cck_weak_sig: CCK weak signal detection state (on/off)
+ * @max_spur_level: Max spur immunity level (chip specific)
+ * @listen_time: Listen time
+ * @ofdm_errors: OFDM timing error count
+ * @cck_errors: CCK timing error count
+ * @last_cc: The &struct ath_cycle_counters (for stats)
+ * @last_listen: Listen time from previous run (for stats)
+ * @last_ofdm_errors: OFDM timing error count from previous run (for tats)
+ * @last_cck_errors: CCK timing error count from previous run (for stats)
+ * @sum_ofdm_errors: Sum of OFDM timing errors (for stats)
+ * @sum_cck_errors: Sum of all CCK timing errors (for stats)
+ */
+struct ath5k_ani_state {
+	enum ath5k_ani_mode	ani_mode;
+
+	/* state */
+	int			noise_imm_level;
+	int			spur_level;
+	int			firstep_level;
+	bool			ofdm_weak_sig;
+	bool			cck_weak_sig;
+
+	int			max_spur_level;
+
+	/* used by the algorithm */
+	unsigned int		listen_time;
+	unsigned int		ofdm_errors;
+	unsigned int		cck_errors;
+
+	/* debug/statistics only: numbers from last ANI calibration */
+	struct ath_cycle_counters last_cc;
+	unsigned int		last_listen;
+	unsigned int		last_ofdm_errors;
+	unsigned int		last_cck_errors;
+	unsigned int		sum_ofdm_errors;
+	unsigned int		sum_cck_errors;
+};
+
+void ath5k_ani_init(struct ath5k_hw *ah, enum ath5k_ani_mode mode);
+void ath5k_ani_mib_intr(struct ath5k_hw *ah);
+void ath5k_ani_calibration(struct ath5k_hw *ah);
+void ath5k_ani_phy_error_report(struct ath5k_hw *ah,
+				enum ath5k_phy_error_code phyerr);
+
+/* for manual control */
+void ath5k_ani_set_noise_immunity_level(struct ath5k_hw *ah, int level);
+void ath5k_ani_set_spur_immunity_level(struct ath5k_hw *ah, int level);
+void ath5k_ani_set_firstep_level(struct ath5k_hw *ah, int level);
+void ath5k_ani_set_ofdm_weak_signal_detection(struct ath5k_hw *ah, bool on);
+void ath5k_ani_set_cck_weak_signal_detection(struct ath5k_hw *ah, bool on);
+
+void ath5k_ani_print_counters(struct ath5k_hw *ah);
+
+#endif /* ANI_H */

linux-7.2.3/drivers/net/wireless/ath/ath5k/attach.c

@@ -0,0 +1,359 @@
+/*
+ * Copyright (c) 2004-2008 Reyk Floeter <reyk@openbsd.org>
+ * Copyright (c) 2006-2008 Nick Kossifidis <mickflemm@gmail.com>
+ *
+ * Permission to use, copy, modify, and distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+/*************************************\
+* Attach/Detach Functions and helpers *
+\*************************************/
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/pci.h>
+#include <linux/slab.h>
+#include "ath5k.h"
+#include "reg.h"
+#include "debug.h"
+
+/**
+ * ath5k_hw_post() - Power On Self Test helper function
+ * @ah: The &struct ath5k_hw
+ */
+static int ath5k_hw_post(struct ath5k_hw *ah)
+{
+
+	static const u32 static_pattern[4] = {
+		0x55555555,	0xaaaaaaaa,
+		0x66666666,	0x99999999
+	};
+	static const u16 regs[2] = { AR5K_STA_ID0, AR5K_PHY(8) };
+	int i, c;
+	u16 cur_reg;
+	u32 var_pattern;
+	u32 init_val;
+	u32 cur_val;
+
+	for (c = 0; c < 2; c++) {
+
+		cur_reg = regs[c];
+
+		/* Save previous value */
+		init_val = ath5k_hw_reg_read(ah, cur_reg);
+
+		for (i = 0; i < 256; i++) {
+			var_pattern = i << 16 | i;
+			ath5k_hw_reg_write(ah, var_pattern, cur_reg);
+			cur_val = ath5k_hw_reg_read(ah, cur_reg);
+
+			if (cur_val != var_pattern) {
+				ATH5K_ERR(ah, "POST Failed !!!\n");
+				return -EAGAIN;
+			}
+
+			/* Found on ndiswrapper dumps */
+			var_pattern = 0x0039080f;
+			ath5k_hw_reg_write(ah, var_pattern, cur_reg);
+		}
+
+		for (i = 0; i < 4; i++) {
+			var_pattern = static_pattern[i];
+			ath5k_hw_reg_write(ah, var_pattern, cur_reg);
+			cur_val = ath5k_hw_reg_read(ah, cur_reg);
+
+			if (cur_val != var_pattern) {
+				ATH5K_ERR(ah, "POST Failed !!!\n");
+				return -EAGAIN;
+			}
+
+			/* Found on ndiswrapper dumps */
+			var_pattern = 0x003b080f;
+			ath5k_hw_reg_write(ah, var_pattern, cur_reg);
+		}
+
+		/* Restore previous value */
+		ath5k_hw_reg_write(ah, init_val, cur_reg);
+
+	}
+
+	return 0;
+
+}
+
+/**
+ * ath5k_hw_init() - Check if hw is supported and init the needed structs
+ * @ah: The &struct ath5k_hw associated with the device
+ *
+ * Check if the device is supported, perform a POST and initialize the needed
+ * structs. Returns -ENOMEM if we don't have memory for the needed structs,
+ * -ENODEV if the device is not supported or prints an error msg if something
+ * else went wrong.
+ */
+int ath5k_hw_init(struct ath5k_hw *ah)
+{
+	static const u8 zero_mac[ETH_ALEN] = { };
+	struct ath_common *common = ath5k_hw_common(ah);
+	struct pci_dev *pdev = ah->pdev;
+	struct ath5k_eeprom_info *ee;
+	int ret;
+	u32 srev;
+
+	/*
+	 * HW information
+	 */
+	ah->ah_bwmode = AR5K_BWMODE_DEFAULT;
+	ah->ah_txpower.txp_tpc = AR5K_TUNE_TPC_TXPOWER;
+	ah->ah_imr = 0;
+	ah->ah_retry_short = AR5K_INIT_RETRY_SHORT;
+	ah->ah_retry_long = AR5K_INIT_RETRY_LONG;
+	ah->ah_ant_mode = AR5K_ANTMODE_DEFAULT;
+	ah->ah_noise_floor = -95;	/* until first NF calibration is run */
+	ah->ani_state.ani_mode = ATH5K_ANI_MODE_AUTO;
+	ah->ah_current_channel = &ah->channels[0];
+
+	/*
+	 * Find the mac version
+	 */
+	ath5k_hw_read_srev(ah);
+	srev = ah->ah_mac_srev;
+	if (srev < AR5K_SREV_AR5311)
+		ah->ah_version = AR5K_AR5210;
+	else if (srev < AR5K_SREV_AR5212)
+		ah->ah_version = AR5K_AR5211;
+	else
+		ah->ah_version = AR5K_AR5212;
+
+	/* Get the MAC version */
+	ah->ah_mac_version = AR5K_REG_MS(srev, AR5K_SREV_VER);
+
+	/* Fill the ath5k_hw struct with the needed functions */
+	ret = ath5k_hw_init_desc_functions(ah);
+	if (ret)
+		goto err;
+
+	/* Bring device out of sleep and reset its units */
+	ret = ath5k_hw_nic_wakeup(ah, NULL);
+	if (ret)
+		goto err;
+
+	/* Get PHY and RADIO revisions */
+	ah->ah_phy_revision = ath5k_hw_reg_read(ah, AR5K_PHY_CHIP_ID) &
+			0xffffffff;
+	ah->ah_radio_5ghz_revision = ath5k_hw_radio_revision(ah,
+			NL80211_BAND_5GHZ);
+
+	/* Try to identify radio chip based on its srev */
+	switch (ah->ah_radio_5ghz_revision & 0xf0) {
+	case AR5K_SREV_RAD_5111:
+		ah->ah_radio = AR5K_RF5111;
+		ah->ah_single_chip = false;
+		ah->ah_radio_2ghz_revision = ath5k_hw_radio_revision(ah,
+							NL80211_BAND_2GHZ);
+		break;
+	case AR5K_SREV_RAD_5112:
+	case AR5K_SREV_RAD_2112:
+		ah->ah_radio = AR5K_RF5112;
+		ah->ah_single_chip = false;
+		ah->ah_radio_2ghz_revision = ath5k_hw_radio_revision(ah,
+							NL80211_BAND_2GHZ);
+		break;
+	case AR5K_SREV_RAD_2413:
+		ah->ah_radio = AR5K_RF2413;
+		ah->ah_single_chip = true;
+		break;
+	case AR5K_SREV_RAD_5413:
+		ah->ah_radio = AR5K_RF5413;
+		ah->ah_single_chip = true;
+		break;
+	case AR5K_SREV_RAD_2316:
+		ah->ah_radio = AR5K_RF2316;
+		ah->ah_single_chip = true;
+		break;
+	case AR5K_SREV_RAD_2317:
+		ah->ah_radio = AR5K_RF2317;
+		ah->ah_single_chip = true;
+		break;
+	case AR5K_SREV_RAD_5424:
+		if (ah->ah_mac_version == AR5K_SREV_AR2425 ||
+		    ah->ah_mac_version == AR5K_SREV_AR2417) {
+			ah->ah_radio = AR5K_RF2425;
+			ah->ah_single_chip = true;
+		} else {
+			ah->ah_radio = AR5K_RF5413;
+			ah->ah_single_chip = true;
+		}
+		break;
+	default:
+		/* Identify radio based on mac/phy srev */
+		if (ah->ah_version == AR5K_AR5210) {
+			ah->ah_radio = AR5K_RF5110;
+			ah->ah_single_chip = false;
+		} else if (ah->ah_version == AR5K_AR5211) {
+			ah->ah_radio = AR5K_RF5111;
+			ah->ah_single_chip = false;
+			ah->ah_radio_2ghz_revision = ath5k_hw_radio_revision(ah,
+							NL80211_BAND_2GHZ);
+		} else if (ah->ah_mac_version == (AR5K_SREV_AR2425 >> 4) ||
+			   ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4) ||
+			   ah->ah_phy_revision == AR5K_SREV_PHY_2425) {
+			ah->ah_radio = AR5K_RF2425;
+			ah->ah_single_chip = true;
+			ah->ah_radio_5ghz_revision = AR5K_SREV_RAD_2425;
+		} else if (srev == AR5K_SREV_AR5213A &&
+			   ah->ah_phy_revision == AR5K_SREV_PHY_5212B) {
+			ah->ah_radio = AR5K_RF5112;
+			ah->ah_single_chip = false;
+			ah->ah_radio_5ghz_revision = AR5K_SREV_RAD_5112B;
+		} else if (ah->ah_mac_version == (AR5K_SREV_AR2415 >> 4) ||
+			   ah->ah_mac_version == (AR5K_SREV_AR2315_R6 >> 4)) {
+			ah->ah_radio = AR5K_RF2316;
+			ah->ah_single_chip = true;
+			ah->ah_radio_5ghz_revision = AR5K_SREV_RAD_2316;
+		} else if (ah->ah_mac_version == (AR5K_SREV_AR5414 >> 4) ||
+			   ah->ah_phy_revision == AR5K_SREV_PHY_5413) {
+			ah->ah_radio = AR5K_RF5413;
+			ah->ah_single_chip = true;
+			ah->ah_radio_5ghz_revision = AR5K_SREV_RAD_5413;
+		} else if (ah->ah_mac_version == (AR5K_SREV_AR2414 >> 4) ||
+			   ah->ah_phy_revision == AR5K_SREV_PHY_2413) {
+			ah->ah_radio = AR5K_RF2413;
+			ah->ah_single_chip = true;
+			ah->ah_radio_5ghz_revision = AR5K_SREV_RAD_2413;
+		} else {
+			ATH5K_ERR(ah, "Couldn't identify radio revision.\n");
+			ret = -ENODEV;
+			goto err;
+		}
+	}
+
+
+	/* Return on unsupported chips (unsupported eeprom etc) */
+	if ((srev >= AR5K_SREV_AR5416) && (srev < AR5K_SREV_AR2425)) {
+		ATH5K_ERR(ah, "Device not yet supported.\n");
+		ret = -ENODEV;
+		goto err;
+	}
+
+	/*
+	 * POST
+	 */
+	ret = ath5k_hw_post(ah);
+	if (ret)
+		goto err;
+
+	/* Enable pci core retry fix on Hainan (5213A) and later chips */
+	if (srev >= AR5K_SREV_AR5213A)
+		AR5K_REG_ENABLE_BITS(ah, AR5K_PCICFG, AR5K_PCICFG_RETRY_FIX);
+
+	/*
+	 * Get card capabilities, calibration values etc
+	 * TODO: EEPROM work
+	 */
+	ret = ath5k_eeprom_init(ah);
+	if (ret) {
+		ATH5K_ERR(ah, "unable to init EEPROM\n");
+		goto err;
+	}
+
+	ee = &ah->ah_capabilities.cap_eeprom;
+
+	/*
+	 * Write PCI-E power save settings
+	 */
+	if ((ah->ah_version == AR5K_AR5212) && pdev && (pci_is_pcie(pdev))) {
+		ath5k_hw_reg_write(ah, 0x9248fc00, AR5K_PCIE_SERDES);
+		ath5k_hw_reg_write(ah, 0x24924924, AR5K_PCIE_SERDES);
+
+		/* Shut off RX when elecidle is asserted */
+		ath5k_hw_reg_write(ah, 0x28000039, AR5K_PCIE_SERDES);
+		ath5k_hw_reg_write(ah, 0x53160824, AR5K_PCIE_SERDES);
+
+		/* If serdes programming is enabled, increase PCI-E
+		 * tx power for systems with long trace from host
+		 * to minicard connector. */
+		if (ee->ee_serdes)
+			ath5k_hw_reg_write(ah, 0xe5980579, AR5K_PCIE_SERDES);
+		else
+			ath5k_hw_reg_write(ah, 0xf6800579, AR5K_PCIE_SERDES);
+
+		/* Shut off PLL and CLKREQ active in L1 */
+		ath5k_hw_reg_write(ah, 0x001defff, AR5K_PCIE_SERDES);
+
+		/* Preserve other settings */
+		ath5k_hw_reg_write(ah, 0x1aaabe40, AR5K_PCIE_SERDES);
+		ath5k_hw_reg_write(ah, 0xbe105554, AR5K_PCIE_SERDES);
+		ath5k_hw_reg_write(ah, 0x000e3007, AR5K_PCIE_SERDES);
+
+		/* Reset SERDES to load new settings */
+		ath5k_hw_reg_write(ah, 0x00000000, AR5K_PCIE_SERDES_RESET);
+		usleep_range(1000, 1500);
+	}
+
+	/* Get misc capabilities */
+	ret = ath5k_hw_set_capabilities(ah);
+	if (ret) {
+		ATH5K_ERR(ah, "unable to get device capabilities\n");
+		goto err;
+	}
+
+	/* Crypto settings */
+	common->keymax = (ah->ah_version == AR5K_AR5210 ?
+			  AR5K_KEYTABLE_SIZE_5210 : AR5K_KEYTABLE_SIZE_5211);
+
+	if (srev >= AR5K_SREV_AR5212_V4 &&
+	    (ee->ee_version < AR5K_EEPROM_VERSION_5_0 ||
+	    !AR5K_EEPROM_AES_DIS(ee->ee_misc5)))
+		common->crypt_caps |= ATH_CRYPT_CAP_CIPHER_AESCCM;
+
+	if (srev >= AR5K_SREV_AR2414) {
+		common->crypt_caps |= ATH_CRYPT_CAP_MIC_COMBINED;
+		AR5K_REG_ENABLE_BITS(ah, AR5K_MISC_MODE,
+			AR5K_MISC_MODE_COMBINED_MIC);
+	}
+
+	/* MAC address is cleared until add_interface */
+	ath5k_hw_set_lladdr(ah, zero_mac);
+
+	/* Set BSSID to bcast address: ff:ff:ff:ff:ff:ff for now */
+	eth_broadcast_addr(common->curbssid);
+	ath5k_hw_set_bssid(ah);
+	ath5k_hw_set_opmode(ah, ah->opmode);
+
+	ath5k_hw_rfgain_opt_init(ah);
+
+	ath5k_hw_init_nfcal_hist(ah);
+
+	/* turn on HW LEDs */
+	ath5k_hw_set_ledstate(ah, AR5K_LED_INIT);
+
+	return 0;
+err:
+	return ret;
+}
+
+/**
+ * ath5k_hw_deinit() - Free the &struct ath5k_hw
+ * @ah: The &struct ath5k_hw
+ */
+void ath5k_hw_deinit(struct ath5k_hw *ah)
+{
+	__set_bit(ATH_STAT_INVALID, ah->status);
+
+	kfree(ah->ah_rf_banks);
+
+	ath5k_eeprom_detach(ah);
+
+	/* assume interrupts are down */
+}

linux-7.2.3/drivers/net/wireless/ath/ath5k/base.h

@@ -0,0 +1,121 @@
+/*-
+ * Copyright (c) 2002-2007 Sam Leffler, Errno Consulting
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer,
+ *    without modification.
+ * 2. Redistributions in binary form must reproduce at minimum a disclaimer
+ *    similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
+ *    redistribution must be conditioned upon including a substantially
+ *    similar Disclaimer requirement for further binary redistribution.
+ * 3. Neither the names of the above-listed copyright holders nor the names
+ *    of any contributors may be used to endorse or promote products derived
+ *    from this software without specific prior written permission.
+ *
+ * Alternatively, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") version 2 as published by the Free
+ * Software Foundation.
+ *
+ * NO WARRANTY
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
+ * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
+ * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
+ * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
+ * THE POSSIBILITY OF SUCH DAMAGES.
+ *
+ */
+
+/*
+ * Definitions for the Atheros Wireless LAN controller driver.
+ */
+#ifndef _DEV_ATH5K_BASE_H
+#define _DEV_ATH5K_BASE_H
+
+struct ieee80211_vif;
+struct ieee80211_hw;
+struct ath5k_hw;
+struct ath5k_txq;
+struct ieee80211_channel;
+struct ath_bus_ops;
+struct ieee80211_tx_control;
+enum nl80211_iftype;
+
+enum ath5k_srev_type {
+	AR5K_VERSION_MAC,
+	AR5K_VERSION_RAD,
+};
+
+struct ath5k_srev_name {
+	const char		*sr_name;
+	enum ath5k_srev_type	sr_type;
+	u_int			sr_val;
+};
+
+struct ath5k_buf {
+	struct list_head		list;
+	struct ath5k_desc		*desc;		/* virtual addr of desc */
+	dma_addr_t			daddr;		/* physical addr of desc */
+	struct sk_buff			*skb;		/* skbuff for buf */
+	dma_addr_t			skbaddr;	/* physical addr of skb data */
+	struct ieee80211_tx_rate	rates[4];	/* number of multi-rate stages */
+};
+
+struct ath5k_vif {
+	bool			assoc; /* are we associated or not */
+	enum nl80211_iftype	opmode;
+	int			bslot;
+	struct ath5k_buf	*bbuf; /* beacon buffer */
+};
+
+struct ath5k_vif_iter_data {
+	const u8	*hw_macaddr;
+	u8		mask[ETH_ALEN];
+	u8		active_mac[ETH_ALEN]; /* first active MAC */
+	bool		need_set_hw_addr;
+	bool		found_active;
+	bool		any_assoc;
+	enum nl80211_iftype opmode;
+	int n_stas;
+};
+
+void ath5k_vif_iter(void *data, u8 *mac, struct ieee80211_vif *vif);
+bool ath5k_any_vif_assoc(struct ath5k_hw *ah);
+
+int ath5k_start(struct ieee80211_hw *hw);
+void ath5k_stop(struct ieee80211_hw *hw, bool suspend);
+
+void ath5k_beacon_update_timers(struct ath5k_hw *ah, u64 bc_tsf);
+int ath5k_beacon_update(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
+void ath5k_beacon_config(struct ath5k_hw *ah);
+void ath5k_set_beacon_filter(struct ieee80211_hw *hw, bool enable);
+
+void ath5k_update_bssid_mask_and_opmode(struct ath5k_hw *ah,
+					struct ieee80211_vif *vif);
+int ath5k_chan_set(struct ath5k_hw *ah, struct cfg80211_chan_def *chandef);
+void ath5k_txbuf_free_skb(struct ath5k_hw *ah, struct ath5k_buf *bf);
+void ath5k_rxbuf_free_skb(struct ath5k_hw *ah, struct ath5k_buf *bf);
+void ath5k_tx_queue(struct ieee80211_hw *hw, struct sk_buff *skb,
+		    struct ath5k_txq *txq, struct ieee80211_tx_control *control);
+
+const char *ath5k_chip_name(enum ath5k_srev_type type, u_int16_t val);
+
+int ath5k_init_ah(struct ath5k_hw *ah, const struct ath_bus_ops *bus_ops);
+void ath5k_deinit_ah(struct ath5k_hw *ah);
+
+/* Check whether BSSID mask is supported */
+#define ath5k_hw_hasbssidmask(_ah) (ah->ah_version == AR5K_AR5212)
+
+/* Check whether virtual EOL is supported */
+#define ath5k_hw_hasveol(_ah) (ah->ah_version != AR5K_AR5210)
+
+#endif	/* _DEV_ATH5K_BASE_H */

linux-7.2.3/drivers/net/wireless/ath/ath5k/caps.c

@@ -0,0 +1,154 @@
+/*
+ * Copyright (c) 2004-2008 Reyk Floeter <reyk@openbsd.org>
+ * Copyright (c) 2006-2008 Nick Kossifidis <mickflemm@gmail.com>
+ * Copyright (c) 2007-2008 Jiri Slaby <jirislaby@gmail.com>
+ *
+ * Permission to use, copy, modify, and distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+/**************\
+* Capabilities *
+\**************/
+
+#include "ath5k.h"
+#include "reg.h"
+#include "debug.h"
+#include "../regd.h"
+
+/*
+ * Fill the capabilities struct
+ * TODO: Merge this with EEPROM code when we are done with it
+ */
+int ath5k_hw_set_capabilities(struct ath5k_hw *ah)
+{
+	struct ath5k_capabilities *caps = &ah->ah_capabilities;
+	u16 ee_header;
+
+	/* Capabilities stored in the EEPROM */
+	ee_header = caps->cap_eeprom.ee_header;
+
+	if (ah->ah_version == AR5K_AR5210) {
+		/*
+		 * Set radio capabilities
+		 * (The AR5110 only supports the middle 5GHz band)
+		 */
+		caps->cap_range.range_5ghz_min = 5120;
+		caps->cap_range.range_5ghz_max = 5430;
+		caps->cap_range.range_2ghz_min = 0;
+		caps->cap_range.range_2ghz_max = 0;
+
+		/* Set supported modes */
+		__set_bit(AR5K_MODE_11A, caps->cap_mode);
+	} else {
+		/*
+		 * XXX The transceiver supports frequencies from 4920 to 6100MHz
+		 * XXX and from 2312 to 2732MHz. There are problems with the
+		 * XXX current ieee80211 implementation because the IEEE
+		 * XXX channel mapping does not support negative channel
+		 * XXX numbers (2312MHz is channel -19). Of course, this
+		 * XXX doesn't matter because these channels are out of the
+		 * XXX legal range.
+		 */
+
+		/*
+		 * Set radio capabilities
+		 */
+
+		if (AR5K_EEPROM_HDR_11A(ee_header)) {
+			if (ath_is_49ghz_allowed(caps->cap_eeprom.ee_regdomain))
+				caps->cap_range.range_5ghz_min = 4920;
+			else
+				caps->cap_range.range_5ghz_min = 5005;
+			caps->cap_range.range_5ghz_max = 6100;
+
+			/* Set supported modes */
+			__set_bit(AR5K_MODE_11A, caps->cap_mode);
+		}
+
+		/* Enable  802.11b if a 2GHz capable radio (2111/5112) is
+		 * connected */
+		if (AR5K_EEPROM_HDR_11B(ee_header) ||
+		    (AR5K_EEPROM_HDR_11G(ee_header) &&
+		     ah->ah_version != AR5K_AR5211)) {
+			/* 2312 */
+			caps->cap_range.range_2ghz_min = 2412;
+			caps->cap_range.range_2ghz_max = 2732;
+
+			/* Override 2GHz modes on SoCs that need it
+			 * NOTE: cap_needs_2GHz_ovr gets set from
+			 * ath_ahb_probe */
+			if (!caps->cap_needs_2GHz_ovr) {
+				if (AR5K_EEPROM_HDR_11B(ee_header))
+					__set_bit(AR5K_MODE_11B,
+							caps->cap_mode);
+
+				if (AR5K_EEPROM_HDR_11G(ee_header) &&
+				ah->ah_version != AR5K_AR5211)
+					__set_bit(AR5K_MODE_11G,
+							caps->cap_mode);
+			}
+		}
+	}
+
+	if ((ah->ah_radio_5ghz_revision & 0xf0) == AR5K_SREV_RAD_2112)
+		__clear_bit(AR5K_MODE_11A, caps->cap_mode);
+
+	/* Set number of supported TX queues */
+	if (ah->ah_version == AR5K_AR5210)
+		caps->cap_queues.q_tx_num = AR5K_NUM_TX_QUEUES_NOQCU;
+	else
+		caps->cap_queues.q_tx_num = AR5K_NUM_TX_QUEUES;
+
+	/* Newer hardware has PHY error counters */
+	if (ah->ah_mac_srev >= AR5K_SREV_AR5213A)
+		caps->cap_has_phyerr_counters = true;
+	else
+		caps->cap_has_phyerr_counters = false;
+
+	/* MACs since AR5212 have MRR support */
+	if (ah->ah_version == AR5K_AR5212)
+		caps->cap_has_mrr_support = true;
+	else
+		caps->cap_has_mrr_support = false;
+
+	return 0;
+}
+
+/*
+ * TODO: Following functions should be part of a new function
+ * set_capability
+ */
+
+int ath5k_hw_enable_pspoll(struct ath5k_hw *ah, u8 *bssid,
+		u16 assoc_id)
+{
+	if (ah->ah_version == AR5K_AR5210) {
+		AR5K_REG_DISABLE_BITS(ah, AR5K_STA_ID1,
+			AR5K_STA_ID1_NO_PSPOLL | AR5K_STA_ID1_DEFAULT_ANTENNA);
+		return 0;
+	}
+
+	return -EIO;
+}
+
+int ath5k_hw_disable_pspoll(struct ath5k_hw *ah)
+{
+	if (ah->ah_version == AR5K_AR5210) {
+		AR5K_REG_ENABLE_BITS(ah, AR5K_STA_ID1,
+			AR5K_STA_ID1_NO_PSPOLL | AR5K_STA_ID1_DEFAULT_ANTENNA);
+		return 0;
+	}
+
+	return -EIO;
+}

linux-7.2.3/drivers/net/wireless/ath/ath5k/debug.h

@@ -0,0 +1,163 @@
+/*
+ * Copyright (c) 2007 Bruno Randolf <bruno@thinktube.com>
+ *
+ *  This file is free software: you may copy, redistribute and/or modify it
+ *  under the terms of the GNU General Public License as published by the
+ *  Free Software Foundation, either version 2 of the License, or (at your
+ *  option) any later version.
+ *
+ *  This file is distributed in the hope that it will be useful, but
+ *  WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ *  General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ *
+ * This file incorporates work covered by the following copyright and
+ * permission notice:
+ *
+ * Copyright (c) 2002-2005 Sam Leffler, Errno Consulting
+ * Copyright (c) 2004-2005 Atheros Communications, Inc.
+ * Copyright (c) 2006 Devicescape Software, Inc.
+ * Copyright (c) 2007 Jiri Slaby <jirislaby@gmail.com>
+ * Copyright (c) 2007 Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
+ *
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer,
+ *    without modification.
+ * 2. Redistributions in binary form must reproduce at minimum a disclaimer
+ *    similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
+ *    redistribution must be conditioned upon including a substantially
+ *    similar Disclaimer requirement for further binary redistribution.
+ * 3. Neither the names of the above-listed copyright holders nor the names
+ *    of any contributors may be used to endorse or promote products derived
+ *    from this software without specific prior written permission.
+ *
+ * Alternatively, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") version 2 as published by the Free
+ * Software Foundation.
+ *
+ * NO WARRANTY
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
+ * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
+ * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
+ * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
+ * THE POSSIBILITY OF SUCH DAMAGES.
+ */
+
+#ifndef _ATH5K_DEBUG_H
+#define _ATH5K_DEBUG_H
+
+struct ath5k_hw;
+struct sk_buff;
+struct ath5k_buf;
+
+struct ath5k_dbg_info {
+	unsigned int		level;		/* debug level */
+};
+
+/**
+ * enum ath5k_debug_level - ath5k debug level
+ *
+ * @ATH5K_DEBUG_RESET: reset processing
+ * @ATH5K_DEBUG_INTR: interrupt handling
+ * @ATH5K_DEBUG_MODE: mode init/setup
+ * @ATH5K_DEBUG_XMIT: basic xmit operation
+ * @ATH5K_DEBUG_BEACON: beacon handling
+ * @ATH5K_DEBUG_CALIBRATE: periodic calibration
+ * @ATH5K_DEBUG_TXPOWER: transmit power setting
+ * @ATH5K_DEBUG_LED: led management
+ * @ATH5K_DEBUG_DUMPBANDS: dump bands
+ * @ATH5K_DEBUG_DMA: debug dma start/stop
+ * @ATH5K_DEBUG_ANI: debug Adaptive Noise Immunity
+ * @ATH5K_DEBUG_DESC: descriptor setup
+ * @ATH5K_DEBUG_ANY: show at any debug level
+ *
+ * The debug level is used to control the amount and type of debugging output
+ * we want to see. The debug level is given in calls to ATH5K_DBG to specify
+ * where the message should appear, and the user can control the debugging
+ * messages he wants to see, either by the module parameter 'debug' on module
+ * load, or dynamically by using debugfs 'ath5k/phyX/debug'. these levels can
+ * be combined together by bitwise OR.
+ */
+enum ath5k_debug_level {
+	ATH5K_DEBUG_RESET	= 0x00000001,
+	ATH5K_DEBUG_INTR	= 0x00000002,
+	ATH5K_DEBUG_MODE	= 0x00000004,
+	ATH5K_DEBUG_XMIT	= 0x00000008,
+	ATH5K_DEBUG_BEACON	= 0x00000010,
+	ATH5K_DEBUG_CALIBRATE	= 0x00000020,
+	ATH5K_DEBUG_TXPOWER	= 0x00000040,
+	ATH5K_DEBUG_LED		= 0x00000080,
+	ATH5K_DEBUG_DUMPBANDS	= 0x00000400,
+	ATH5K_DEBUG_DMA		= 0x00000800,
+	ATH5K_DEBUG_ANI		= 0x00002000,
+	ATH5K_DEBUG_DESC	= 0x00004000,
+	ATH5K_DEBUG_ANY		= 0xffffffff
+};
+
+#ifdef CONFIG_ATH5K_DEBUG
+
+#define ATH5K_DBG(_sc, _m, _fmt, ...) do { \
+	if (unlikely((_sc)->debug.level & (_m) && net_ratelimit())) \
+		ATH5K_PRINTK(_sc, KERN_DEBUG, "(%s:%d): " _fmt, \
+			__func__, __LINE__, ##__VA_ARGS__); \
+	} while (0)
+
+#define ATH5K_DBG_UNLIMIT(_sc, _m, _fmt, ...) do { \
+	if (unlikely((_sc)->debug.level & (_m))) \
+		ATH5K_PRINTK(_sc, KERN_DEBUG, "(%s:%d): " _fmt, \
+			__func__, __LINE__, ##__VA_ARGS__); \
+	} while (0)
+
+void
+ath5k_debug_init_device(struct ath5k_hw *ah);
+
+void
+ath5k_debug_printrxbuffs(struct ath5k_hw *ah);
+
+void
+ath5k_debug_dump_bands(struct ath5k_hw *ah);
+
+void
+ath5k_debug_printtxbuf(struct ath5k_hw *ah, struct ath5k_buf *bf);
+
+#else /* no debugging */
+
+#include <linux/compiler.h>
+
+static inline __printf(3, 4) void
+ATH5K_DBG(struct ath5k_hw *ah, unsigned int m, const char *fmt, ...) {}
+
+static inline __printf(3, 4) void
+ATH5K_DBG_UNLIMIT(struct ath5k_hw *ah, unsigned int m, const char *fmt, ...)
+{}
+
+static inline void
+ath5k_debug_init_device(struct ath5k_hw *ah) {}
+
+static inline void
+ath5k_debug_printrxbuffs(struct ath5k_hw *ah) {}
+
+static inline void
+ath5k_debug_dump_bands(struct ath5k_hw *ah) {}
+
+static inline void
+ath5k_debug_printtxbuf(struct ath5k_hw *ah, struct ath5k_buf *bf) {}
+
+#endif /* ifdef CONFIG_ATH5K_DEBUG */
+
+#endif /* ifndef _ATH5K_DEBUG_H */

linux-7.2.3/drivers/net/wireless/ath/ath5k/desc.c

@@ -0,0 +1,786 @@
+/*
+ * Copyright (c) 2004-2008 Reyk Floeter <reyk@openbsd.org>
+ * Copyright (c) 2006-2008 Nick Kossifidis <mickflemm@gmail.com>
+ * Copyright (c) 2007-2008 Pavel Roskin <proski@gnu.org>
+ *
+ * Permission to use, copy, modify, and distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+/******************************\
+ Hardware Descriptor Functions
+\******************************/
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include "ath5k.h"
+#include "reg.h"
+#include "debug.h"
+
+
+/**
+ * DOC: Hardware descriptor functions
+ *
+ * Here we handle the processing of the low-level hw descriptors
+ * that hw reads and writes via DMA for each TX and RX attempt (that means
+ * we can also have descriptors for failed TX/RX tries). We have two kind of
+ * descriptors for RX and TX, control descriptors tell the hw how to send or
+ * receive a packet where to read/write it from/to etc and status descriptors
+ * that contain information about how the packet was sent or received (errors
+ * included).
+ *
+ * Descriptor format is not exactly the same for each MAC chip version so we
+ * have function pointers on &struct ath5k_hw we initialize at runtime based on
+ * the chip used.
+ */
+
+
+/************************\
+* TX Control descriptors *
+\************************/
+
+/**
+ * ath5k_hw_setup_2word_tx_desc() - Initialize a 2-word tx control descriptor
+ * @ah: The &struct ath5k_hw
+ * @desc: The &struct ath5k_desc
+ * @pkt_len: Frame length in bytes
+ * @hdr_len: Header length in bytes (only used on AR5210)
+ * @padsize: Any padding we've added to the frame length
+ * @type: One of enum ath5k_pkt_type
+ * @tx_power: Tx power in 0.5dB steps
+ * @tx_rate0: HW idx for transmission rate
+ * @tx_tries0: Max number of retransmissions
+ * @key_index: Index on key table to use for encryption
+ * @antenna_mode: Which antenna to use (0 for auto)
+ * @flags: One of AR5K_TXDESC_* flags (desc.h)
+ * @rtscts_rate: HW idx for RTS/CTS transmission rate
+ * @rtscts_duration: What to put on duration field on the header of RTS/CTS
+ *
+ * Internal function to initialize a 2-Word TX control descriptor
+ * found on AR5210 and AR5211 MACs chips.
+ *
+ * Returns 0 on success or -EINVAL on false input
+ */
+static int
+ath5k_hw_setup_2word_tx_desc(struct ath5k_hw *ah,
+			struct ath5k_desc *desc,
+			unsigned int pkt_len, unsigned int hdr_len,
+			int padsize,
+			enum ath5k_pkt_type type,
+			unsigned int tx_power,
+			unsigned int tx_rate0, unsigned int tx_tries0,
+			unsigned int key_index,
+			unsigned int antenna_mode,
+			unsigned int flags,
+			unsigned int rtscts_rate, unsigned int rtscts_duration)
+{
+	u32 frame_type;
+	struct ath5k_hw_2w_tx_ctl *tx_ctl;
+	unsigned int frame_len;
+
+	tx_ctl = &desc->ud.ds_tx5210.tx_ctl;
+
+	/*
+	 * Validate input
+	 * - Zero retries don't make sense.
+	 * - A zero rate will put the HW into a mode where it continuously sends
+	 *   noise on the channel, so it is important to avoid this.
+	 */
+	if (unlikely(tx_tries0 == 0)) {
+		ATH5K_ERR(ah, "zero retries\n");
+		WARN_ON(1);
+		return -EINVAL;
+	}
+	if (unlikely(tx_rate0 == 0)) {
+		ATH5K_ERR(ah, "zero rate\n");
+		WARN_ON(1);
+		return -EINVAL;
+	}
+
+	/* Clear descriptor */
+	memset(&desc->ud.ds_tx5210, 0, sizeof(struct ath5k_hw_5210_tx_desc));
+
+	/* Setup control descriptor */
+
+	/* Verify and set frame length */
+
+	/* remove padding we might have added before */
+	frame_len = pkt_len - padsize + FCS_LEN;
+
+	if (frame_len & ~AR5K_2W_TX_DESC_CTL0_FRAME_LEN)
+		return -EINVAL;
+
+	tx_ctl->tx_control_0 = frame_len & AR5K_2W_TX_DESC_CTL0_FRAME_LEN;
+
+	/* Verify and set buffer length */
+
+	/* NB: beacon's BufLen must be a multiple of 4 bytes */
+	if (type == AR5K_PKT_TYPE_BEACON)
+		pkt_len = roundup(pkt_len, 4);
+
+	if (pkt_len & ~AR5K_2W_TX_DESC_CTL1_BUF_LEN)
+		return -EINVAL;
+
+	tx_ctl->tx_control_1 = pkt_len & AR5K_2W_TX_DESC_CTL1_BUF_LEN;
+
+	/*
+	 * Verify and set header length (only 5210)
+	 */
+	if (ah->ah_version == AR5K_AR5210) {
+		if (hdr_len & ~AR5K_2W_TX_DESC_CTL0_HEADER_LEN_5210)
+			return -EINVAL;
+		tx_ctl->tx_control_0 |=
+			AR5K_REG_SM(hdr_len, AR5K_2W_TX_DESC_CTL0_HEADER_LEN_5210);
+	}
+
+	/*Differences between 5210-5211*/
+	if (ah->ah_version == AR5K_AR5210) {
+		switch (type) {
+		case AR5K_PKT_TYPE_BEACON:
+		case AR5K_PKT_TYPE_PROBE_RESP:
+			frame_type = AR5K_AR5210_TX_DESC_FRAME_TYPE_NO_DELAY;
+			break;
+		case AR5K_PKT_TYPE_PIFS:
+			frame_type = AR5K_AR5210_TX_DESC_FRAME_TYPE_PIFS;
+			break;
+		default:
+			frame_type = type;
+			break;
+		}
+
+		tx_ctl->tx_control_0 |=
+		AR5K_REG_SM(frame_type, AR5K_2W_TX_DESC_CTL0_FRAME_TYPE_5210) |
+		AR5K_REG_SM(tx_rate0, AR5K_2W_TX_DESC_CTL0_XMIT_RATE);
+
+	} else {
+		tx_ctl->tx_control_0 |=
+			AR5K_REG_SM(tx_rate0, AR5K_2W_TX_DESC_CTL0_XMIT_RATE) |
+			AR5K_REG_SM(antenna_mode,
+				AR5K_2W_TX_DESC_CTL0_ANT_MODE_XMIT);
+		tx_ctl->tx_control_1 |=
+			AR5K_REG_SM(type, AR5K_2W_TX_DESC_CTL1_FRAME_TYPE_5211);
+	}
+
+#define _TX_FLAGS(_c, _flag)					\
+	if (flags & AR5K_TXDESC_##_flag) {			\
+		tx_ctl->tx_control_##_c |=			\
+			AR5K_2W_TX_DESC_CTL##_c##_##_flag;	\
+	}
+#define _TX_FLAGS_5211(_c, _flag)					\
+	if (flags & AR5K_TXDESC_##_flag) {				\
+		tx_ctl->tx_control_##_c |=				\
+			AR5K_2W_TX_DESC_CTL##_c##_##_flag##_5211;	\
+	}
+	_TX_FLAGS(0, CLRDMASK);
+	_TX_FLAGS(0, INTREQ);
+	_TX_FLAGS(0, RTSENA);
+
+	if (ah->ah_version == AR5K_AR5211) {
+		_TX_FLAGS_5211(0, VEOL);
+		_TX_FLAGS_5211(1, NOACK);
+	}
+
+#undef _TX_FLAGS
+#undef _TX_FLAGS_5211
+
+	/*
+	 * WEP crap
+	 */
+	if (key_index != AR5K_TXKEYIX_INVALID) {
+		tx_ctl->tx_control_0 |=
+			AR5K_2W_TX_DESC_CTL0_ENCRYPT_KEY_VALID;
+		tx_ctl->tx_control_1 |=
+			AR5K_REG_SM(key_index,
+			AR5K_2W_TX_DESC_CTL1_ENC_KEY_IDX);
+	}
+
+	/*
+	 * RTS/CTS Duration [5210 ?]
+	 */
+	if ((ah->ah_version == AR5K_AR5210) &&
+			(flags & (AR5K_TXDESC_RTSENA | AR5K_TXDESC_CTSENA)))
+		tx_ctl->tx_control_1 |= rtscts_duration &
+				AR5K_2W_TX_DESC_CTL1_RTS_DURATION_5210;
+
+	return 0;
+}
+
+/**
+ * ath5k_hw_setup_4word_tx_desc() - Initialize a 4-word tx control descriptor
+ * @ah: The &struct ath5k_hw
+ * @desc: The &struct ath5k_desc
+ * @pkt_len: Frame length in bytes
+ * @hdr_len: Header length in bytes (only used on AR5210)
+ * @padsize: Any padding we've added to the frame length
+ * @type: One of enum ath5k_pkt_type
+ * @tx_power: Tx power in 0.5dB steps
+ * @tx_rate0: HW idx for transmission rate
+ * @tx_tries0: Max number of retransmissions
+ * @key_index: Index on key table to use for encryption
+ * @antenna_mode: Which antenna to use (0 for auto)
+ * @flags: One of AR5K_TXDESC_* flags (desc.h)
+ * @rtscts_rate: HW idx for RTS/CTS transmission rate
+ * @rtscts_duration: What to put on duration field on the header of RTS/CTS
+ *
+ * Internal function to initialize a 4-Word TX control descriptor
+ * found on AR5212 and later MACs chips.
+ *
+ * Returns 0 on success or -EINVAL on false input
+ */
+static int
+ath5k_hw_setup_4word_tx_desc(struct ath5k_hw *ah,
+			struct ath5k_desc *desc,
+			unsigned int pkt_len, unsigned int hdr_len,
+			int padsize,
+			enum ath5k_pkt_type type,
+			unsigned int tx_power,
+			unsigned int tx_rate0, unsigned int tx_tries0,
+			unsigned int key_index,
+			unsigned int antenna_mode,
+			unsigned int flags,
+			unsigned int rtscts_rate, unsigned int rtscts_duration)
+{
+	struct ath5k_hw_4w_tx_ctl *tx_ctl;
+	unsigned int frame_len;
+
+	/*
+	 * Use local variables for these to reduce load/store access on
+	 * uncached memory
+	 */
+	u32 txctl0 = 0, txctl1 = 0, txctl2 = 0, txctl3 = 0;
+
+	tx_ctl = &desc->ud.ds_tx5212.tx_ctl;
+
+	/*
+	 * Validate input
+	 * - Zero retries don't make sense.
+	 * - A zero rate will put the HW into a mode where it continuously sends
+	 *   noise on the channel, so it is important to avoid this.
+	 */
+	if (unlikely(tx_tries0 == 0)) {
+		ATH5K_ERR(ah, "zero retries\n");
+		WARN_ON(1);
+		return -EINVAL;
+	}
+	if (unlikely(tx_rate0 == 0)) {
+		ATH5K_ERR(ah, "zero rate\n");
+		WARN_ON(1);
+		return -EINVAL;
+	}
+
+	tx_power += ah->ah_txpower.txp_offset;
+	if (tx_power > AR5K_TUNE_MAX_TXPOWER)
+		tx_power = AR5K_TUNE_MAX_TXPOWER;
+
+	/* Clear descriptor status area */
+	memset(&desc->ud.ds_tx5212.tx_stat, 0,
+	       sizeof(desc->ud.ds_tx5212.tx_stat));
+
+	/* Setup control descriptor */
+
+	/* Verify and set frame length */
+
+	/* remove padding we might have added before */
+	frame_len = pkt_len - padsize + FCS_LEN;
+
+	if (frame_len & ~AR5K_4W_TX_DESC_CTL0_FRAME_LEN)
+		return -EINVAL;
+
+	txctl0 = frame_len & AR5K_4W_TX_DESC_CTL0_FRAME_LEN;
+
+	/* Verify and set buffer length */
+
+	/* NB: beacon's BufLen must be a multiple of 4 bytes */
+	if (type == AR5K_PKT_TYPE_BEACON)
+		pkt_len = roundup(pkt_len, 4);
+
+	if (pkt_len & ~AR5K_4W_TX_DESC_CTL1_BUF_LEN)
+		return -EINVAL;
+
+	txctl1 = pkt_len & AR5K_4W_TX_DESC_CTL1_BUF_LEN;
+
+	txctl0 |= AR5K_REG_SM(tx_power, AR5K_4W_TX_DESC_CTL0_XMIT_POWER) |
+		  AR5K_REG_SM(antenna_mode, AR5K_4W_TX_DESC_CTL0_ANT_MODE_XMIT);
+	txctl1 |= AR5K_REG_SM(type, AR5K_4W_TX_DESC_CTL1_FRAME_TYPE);
+	txctl2 = AR5K_REG_SM(tx_tries0, AR5K_4W_TX_DESC_CTL2_XMIT_TRIES0);
+	txctl3 = tx_rate0 & AR5K_4W_TX_DESC_CTL3_XMIT_RATE0;
+
+#define _TX_FLAGS(_c, _flag)					\
+	if (flags & AR5K_TXDESC_##_flag) {			\
+		txctl##_c |= AR5K_4W_TX_DESC_CTL##_c##_##_flag;	\
+	}
+
+	_TX_FLAGS(0, CLRDMASK);
+	_TX_FLAGS(0, VEOL);
+	_TX_FLAGS(0, INTREQ);
+	_TX_FLAGS(0, RTSENA);
+	_TX_FLAGS(0, CTSENA);
+	_TX_FLAGS(1, NOACK);
+
+#undef _TX_FLAGS
+
+	/*
+	 * WEP crap
+	 */
+	if (key_index != AR5K_TXKEYIX_INVALID) {
+		txctl0 |= AR5K_4W_TX_DESC_CTL0_ENCRYPT_KEY_VALID;
+		txctl1 |= AR5K_REG_SM(key_index,
+				AR5K_4W_TX_DESC_CTL1_ENCRYPT_KEY_IDX);
+	}
+
+	/*
+	 * RTS/CTS
+	 */
+	if (flags & (AR5K_TXDESC_RTSENA | AR5K_TXDESC_CTSENA)) {
+		if ((flags & AR5K_TXDESC_RTSENA) &&
+				(flags & AR5K_TXDESC_CTSENA))
+			return -EINVAL;
+		txctl2 |= rtscts_duration & AR5K_4W_TX_DESC_CTL2_RTS_DURATION;
+		txctl3 |= AR5K_REG_SM(rtscts_rate,
+				AR5K_4W_TX_DESC_CTL3_RTS_CTS_RATE);
+	}
+
+	tx_ctl->tx_control_0 = txctl0;
+	tx_ctl->tx_control_1 = txctl1;
+	tx_ctl->tx_control_2 = txctl2;
+	tx_ctl->tx_control_3 = txctl3;
+
+	return 0;
+}
+
+/**
+ * ath5k_hw_setup_mrr_tx_desc() - Initialize an MRR tx control descriptor
+ * @ah: The &struct ath5k_hw
+ * @desc: The &struct ath5k_desc
+ * @tx_rate1: HW idx for rate used on transmission series 1
+ * @tx_tries1: Max number of retransmissions for transmission series 1
+ * @tx_rate2: HW idx for rate used on transmission series 2
+ * @tx_tries2: Max number of retransmissions for transmission series 2
+ * @tx_rate3: HW idx for rate used on transmission series 3
+ * @tx_tries3: Max number of retransmissions for transmission series 3
+ *
+ * Multi rate retry (MRR) tx control descriptors are available only on AR5212
+ * MACs, they are part of the normal 4-word tx control descriptor (see above)
+ * but we handle them through a separate function for better abstraction.
+ *
+ * Returns 0 on success or -EINVAL on invalid input
+ */
+int
+ath5k_hw_setup_mrr_tx_desc(struct ath5k_hw *ah,
+			struct ath5k_desc *desc,
+			u_int tx_rate1, u_int tx_tries1,
+			u_int tx_rate2, u_int tx_tries2,
+			u_int tx_rate3, u_int tx_tries3)
+{
+	struct ath5k_hw_4w_tx_ctl *tx_ctl;
+
+	/* no mrr support for cards older than 5212 */
+	if (ah->ah_version < AR5K_AR5212)
+		return 0;
+
+	/*
+	 * Rates can be 0 as long as the retry count is 0 too.
+	 * A zero rate and nonzero retry count will put the HW into a mode where
+	 * it continuously sends noise on the channel, so it is important to
+	 * avoid this.
+	 */
+	if (unlikely((tx_rate1 == 0 && tx_tries1 != 0) ||
+		     (tx_rate2 == 0 && tx_tries2 != 0) ||
+		     (tx_rate3 == 0 && tx_tries3 != 0))) {
+		ATH5K_ERR(ah, "zero rate\n");
+		WARN_ON(1);
+		return -EINVAL;
+	}
+
+	if (ah->ah_version == AR5K_AR5212) {
+		tx_ctl = &desc->ud.ds_tx5212.tx_ctl;
+
+#define _XTX_TRIES(_n)							\
+	if (tx_tries##_n) {						\
+		tx_ctl->tx_control_2 |=					\
+		    AR5K_REG_SM(tx_tries##_n,				\
+		    AR5K_4W_TX_DESC_CTL2_XMIT_TRIES##_n);		\
+		tx_ctl->tx_control_3 |=					\
+		    AR5K_REG_SM(tx_rate##_n,				\
+		    AR5K_4W_TX_DESC_CTL3_XMIT_RATE##_n);		\
+	}
+
+		_XTX_TRIES(1);
+		_XTX_TRIES(2);
+		_XTX_TRIES(3);
+
+#undef _XTX_TRIES
+
+		return 1;
+	}
+
+	return 0;
+}
+
+
+/***********************\
+* TX Status descriptors *
+\***********************/
+
+/**
+ * ath5k_hw_proc_2word_tx_status() - Process a tx status descriptor on 5210/1
+ * @ah: The &struct ath5k_hw
+ * @desc: The &struct ath5k_desc
+ * @ts: The &struct ath5k_tx_status
+ */
+static int
+ath5k_hw_proc_2word_tx_status(struct ath5k_hw *ah,
+				struct ath5k_desc *desc,
+				struct ath5k_tx_status *ts)
+{
+	struct ath5k_hw_tx_status *tx_status;
+
+	tx_status = &desc->ud.ds_tx5210.tx_stat;
+
+	/* No frame has been send or error */
+	if (unlikely((tx_status->tx_status_1 & AR5K_DESC_TX_STATUS1_DONE) == 0))
+		return -EINPROGRESS;
+
+	/*
+	 * Get descriptor status
+	 */
+	ts->ts_tstamp = AR5K_REG_MS(tx_status->tx_status_0,
+		AR5K_DESC_TX_STATUS0_SEND_TIMESTAMP);
+	ts->ts_shortretry = AR5K_REG_MS(tx_status->tx_status_0,
+		AR5K_DESC_TX_STATUS0_SHORT_RETRY_COUNT);
+	ts->ts_final_retry = AR5K_REG_MS(tx_status->tx_status_0,
+		AR5K_DESC_TX_STATUS0_LONG_RETRY_COUNT);
+	/*TODO: ts->ts_virtcol + test*/
+	ts->ts_seqnum = AR5K_REG_MS(tx_status->tx_status_1,
+		AR5K_DESC_TX_STATUS1_SEQ_NUM);
+	ts->ts_rssi = AR5K_REG_MS(tx_status->tx_status_1,
+		AR5K_DESC_TX_STATUS1_ACK_SIG_STRENGTH);
+	ts->ts_antenna = 1;
+	ts->ts_status = 0;
+	ts->ts_final_idx = 0;
+
+	if (!(tx_status->tx_status_0 & AR5K_DESC_TX_STATUS0_FRAME_XMIT_OK)) {
+		if (tx_status->tx_status_0 &
+				AR5K_DESC_TX_STATUS0_EXCESSIVE_RETRIES)
+			ts->ts_status |= AR5K_TXERR_XRETRY;
+
+		if (tx_status->tx_status_0 & AR5K_DESC_TX_STATUS0_FIFO_UNDERRUN)
+			ts->ts_status |= AR5K_TXERR_FIFO;
+
+		if (tx_status->tx_status_0 & AR5K_DESC_TX_STATUS0_FILTERED)
+			ts->ts_status |= AR5K_TXERR_FILT;
+	}
+
+	return 0;
+}
+
+/**
+ * ath5k_hw_proc_4word_tx_status() - Process a tx status descriptor on 5212
+ * @ah: The &struct ath5k_hw
+ * @desc: The &struct ath5k_desc
+ * @ts: The &struct ath5k_tx_status
+ */
+static int
+ath5k_hw_proc_4word_tx_status(struct ath5k_hw *ah,
+				struct ath5k_desc *desc,
+				struct ath5k_tx_status *ts)
+{
+	struct ath5k_hw_tx_status *tx_status;
+	u32 txstat0, txstat1;
+
+	tx_status = &desc->ud.ds_tx5212.tx_stat;
+
+	txstat1 = READ_ONCE(tx_status->tx_status_1);
+
+	/* No frame has been send or error */
+	if (unlikely(!(txstat1 & AR5K_DESC_TX_STATUS1_DONE)))
+		return -EINPROGRESS;
+
+	txstat0 = READ_ONCE(tx_status->tx_status_0);
+
+	/*
+	 * Get descriptor status
+	 */
+	ts->ts_tstamp = AR5K_REG_MS(txstat0,
+		AR5K_DESC_TX_STATUS0_SEND_TIMESTAMP);
+	ts->ts_shortretry = AR5K_REG_MS(txstat0,
+		AR5K_DESC_TX_STATUS0_SHORT_RETRY_COUNT);
+	ts->ts_final_retry = AR5K_REG_MS(txstat0,
+		AR5K_DESC_TX_STATUS0_LONG_RETRY_COUNT);
+	ts->ts_seqnum = AR5K_REG_MS(txstat1,
+		AR5K_DESC_TX_STATUS1_SEQ_NUM);
+	ts->ts_rssi = AR5K_REG_MS(txstat1,
+		AR5K_DESC_TX_STATUS1_ACK_SIG_STRENGTH);
+	ts->ts_antenna = (txstat1 &
+		AR5K_DESC_TX_STATUS1_XMIT_ANTENNA_5212) ? 2 : 1;
+	ts->ts_status = 0;
+
+	ts->ts_final_idx = AR5K_REG_MS(txstat1,
+			AR5K_DESC_TX_STATUS1_FINAL_TS_IX_5212);
+
+	/* TX error */
+	if (!(txstat0 & AR5K_DESC_TX_STATUS0_FRAME_XMIT_OK)) {
+		if (txstat0 & AR5K_DESC_TX_STATUS0_EXCESSIVE_RETRIES)
+			ts->ts_status |= AR5K_TXERR_XRETRY;
+
+		if (txstat0 & AR5K_DESC_TX_STATUS0_FIFO_UNDERRUN)
+			ts->ts_status |= AR5K_TXERR_FIFO;
+
+		if (txstat0 & AR5K_DESC_TX_STATUS0_FILTERED)
+			ts->ts_status |= AR5K_TXERR_FILT;
+	}
+
+	return 0;
+}
+
+
+/****************\
+* RX Descriptors *
+\****************/
+
+/**
+ * ath5k_hw_setup_rx_desc() - Initialize an rx control descriptor
+ * @ah: The &struct ath5k_hw
+ * @desc: The &struct ath5k_desc
+ * @size: RX buffer length in bytes
+ * @flags: One of AR5K_RXDESC_* flags
+ */
+int
+ath5k_hw_setup_rx_desc(struct ath5k_hw *ah,
+			struct ath5k_desc *desc,
+			u32 size, unsigned int flags)
+{
+	struct ath5k_hw_rx_ctl *rx_ctl;
+
+	rx_ctl = &desc->ud.ds_rx.rx_ctl;
+
+	/*
+	 * Clear the descriptor
+	 * If we don't clean the status descriptor,
+	 * while scanning we get too many results,
+	 * most of them virtual, after some secs
+	 * of scanning system hangs. M.F.
+	*/
+	memset(&desc->ud.ds_rx, 0, sizeof(struct ath5k_hw_all_rx_desc));
+
+	if (unlikely(size & ~AR5K_DESC_RX_CTL1_BUF_LEN))
+		return -EINVAL;
+
+	/* Setup descriptor */
+	rx_ctl->rx_control_1 = size & AR5K_DESC_RX_CTL1_BUF_LEN;
+
+	if (flags & AR5K_RXDESC_INTREQ)
+		rx_ctl->rx_control_1 |= AR5K_DESC_RX_CTL1_INTREQ;
+
+	return 0;
+}
+
+/**
+ * ath5k_hw_proc_5210_rx_status() - Process the rx status descriptor on 5210/1
+ * @ah: The &struct ath5k_hw
+ * @desc: The &struct ath5k_desc
+ * @rs: The &struct ath5k_rx_status
+ *
+ * Internal function used to process an RX status descriptor
+ * on AR5210/5211 MAC.
+ *
+ * Returns 0 on success or -EINPROGRESS in case we haven't received the who;e
+ * frame yet.
+ */
+static int
+ath5k_hw_proc_5210_rx_status(struct ath5k_hw *ah,
+				struct ath5k_desc *desc,
+				struct ath5k_rx_status *rs)
+{
+	struct ath5k_hw_rx_status *rx_status;
+
+	rx_status = &desc->ud.ds_rx.rx_stat;
+
+	/* No frame received / not ready */
+	if (unlikely(!(rx_status->rx_status_1 &
+			AR5K_5210_RX_DESC_STATUS1_DONE)))
+		return -EINPROGRESS;
+
+	memset(rs, 0, sizeof(struct ath5k_rx_status));
+
+	/*
+	 * Frame receive status
+	 */
+	rs->rs_datalen = rx_status->rx_status_0 &
+		AR5K_5210_RX_DESC_STATUS0_DATA_LEN;
+	rs->rs_rssi = AR5K_REG_MS(rx_status->rx_status_0,
+		AR5K_5210_RX_DESC_STATUS0_RECEIVE_SIGNAL);
+	rs->rs_rate = AR5K_REG_MS(rx_status->rx_status_0,
+		AR5K_5210_RX_DESC_STATUS0_RECEIVE_RATE);
+	rs->rs_more = !!(rx_status->rx_status_0 &
+		AR5K_5210_RX_DESC_STATUS0_MORE);
+	/* TODO: this timestamp is 13 bit, later on we assume 15 bit!
+	 * also the HAL code for 5210 says the timestamp is bits [10..22] of the
+	 * TSF, and extends the timestamp here to 15 bit.
+	 * we need to check on 5210...
+	 */
+	rs->rs_tstamp = AR5K_REG_MS(rx_status->rx_status_1,
+		AR5K_5210_RX_DESC_STATUS1_RECEIVE_TIMESTAMP);
+
+	if (ah->ah_version == AR5K_AR5211)
+		rs->rs_antenna = AR5K_REG_MS(rx_status->rx_status_0,
+				AR5K_5210_RX_DESC_STATUS0_RECEIVE_ANT_5211);
+	else
+		rs->rs_antenna = (rx_status->rx_status_0 &
+				AR5K_5210_RX_DESC_STATUS0_RECEIVE_ANT_5210)
+				? 2 : 1;
+
+	/*
+	 * Key table status
+	 */
+	if (rx_status->rx_status_1 & AR5K_5210_RX_DESC_STATUS1_KEY_INDEX_VALID)
+		rs->rs_keyix = AR5K_REG_MS(rx_status->rx_status_1,
+			AR5K_5210_RX_DESC_STATUS1_KEY_INDEX);
+	else
+		rs->rs_keyix = AR5K_RXKEYIX_INVALID;
+
+	/*
+	 * Receive/descriptor errors
+	 */
+	if (!(rx_status->rx_status_1 &
+			AR5K_5210_RX_DESC_STATUS1_FRAME_RECEIVE_OK)) {
+		if (rx_status->rx_status_1 &
+				AR5K_5210_RX_DESC_STATUS1_CRC_ERROR)
+			rs->rs_status |= AR5K_RXERR_CRC;
+
+		/* only on 5210 */
+		if ((ah->ah_version == AR5K_AR5210) &&
+		    (rx_status->rx_status_1 &
+				AR5K_5210_RX_DESC_STATUS1_FIFO_OVERRUN_5210))
+			rs->rs_status |= AR5K_RXERR_FIFO;
+
+		if (rx_status->rx_status_1 &
+				AR5K_5210_RX_DESC_STATUS1_PHY_ERROR) {
+			rs->rs_status |= AR5K_RXERR_PHY;
+			rs->rs_phyerr = AR5K_REG_MS(rx_status->rx_status_1,
+				AR5K_5210_RX_DESC_STATUS1_PHY_ERROR);
+		}
+
+		if (rx_status->rx_status_1 &
+				AR5K_5210_RX_DESC_STATUS1_DECRYPT_CRC_ERROR)
+			rs->rs_status |= AR5K_RXERR_DECRYPT;
+	}
+
+	return 0;
+}
+
+/**
+ * ath5k_hw_proc_5212_rx_status() - Process the rx status descriptor on 5212
+ * @ah: The &struct ath5k_hw
+ * @desc: The &struct ath5k_desc
+ * @rs: The &struct ath5k_rx_status
+ *
+ * Internal function used to process an RX status descriptor
+ * on AR5212 and later MAC.
+ *
+ * Returns 0 on success or -EINPROGRESS in case we haven't received the who;e
+ * frame yet.
+ */
+static int
+ath5k_hw_proc_5212_rx_status(struct ath5k_hw *ah,
+				struct ath5k_desc *desc,
+				struct ath5k_rx_status *rs)
+{
+	struct ath5k_hw_rx_status *rx_status;
+	u32 rxstat0, rxstat1;
+
+	rx_status = &desc->ud.ds_rx.rx_stat;
+	rxstat1 = READ_ONCE(rx_status->rx_status_1);
+
+	/* No frame received / not ready */
+	if (unlikely(!(rxstat1 & AR5K_5212_RX_DESC_STATUS1_DONE)))
+		return -EINPROGRESS;
+
+	memset(rs, 0, sizeof(struct ath5k_rx_status));
+	rxstat0 = READ_ONCE(rx_status->rx_status_0);
+
+	/*
+	 * Frame receive status
+	 */
+	rs->rs_datalen = rxstat0 & AR5K_5212_RX_DESC_STATUS0_DATA_LEN;
+	rs->rs_rssi = AR5K_REG_MS(rxstat0,
+		AR5K_5212_RX_DESC_STATUS0_RECEIVE_SIGNAL);
+	rs->rs_rate = AR5K_REG_MS(rxstat0,
+		AR5K_5212_RX_DESC_STATUS0_RECEIVE_RATE);
+	rs->rs_antenna = AR5K_REG_MS(rxstat0,
+		AR5K_5212_RX_DESC_STATUS0_RECEIVE_ANTENNA);
+	rs->rs_more = !!(rxstat0 & AR5K_5212_RX_DESC_STATUS0_MORE);
+	rs->rs_tstamp = AR5K_REG_MS(rxstat1,
+		AR5K_5212_RX_DESC_STATUS1_RECEIVE_TIMESTAMP);
+
+	/*
+	 * Key table status
+	 */
+	if (rxstat1 & AR5K_5212_RX_DESC_STATUS1_KEY_INDEX_VALID)
+		rs->rs_keyix = AR5K_REG_MS(rxstat1,
+					   AR5K_5212_RX_DESC_STATUS1_KEY_INDEX);
+	else
+		rs->rs_keyix = AR5K_RXKEYIX_INVALID;
+
+	/*
+	 * Receive/descriptor errors
+	 */
+	if (!(rxstat1 & AR5K_5212_RX_DESC_STATUS1_FRAME_RECEIVE_OK)) {
+		if (rxstat1 & AR5K_5212_RX_DESC_STATUS1_CRC_ERROR)
+			rs->rs_status |= AR5K_RXERR_CRC;
+
+		if (rxstat1 & AR5K_5212_RX_DESC_STATUS1_PHY_ERROR) {
+			rs->rs_status |= AR5K_RXERR_PHY;
+			rs->rs_phyerr = AR5K_REG_MS(rxstat1,
+				AR5K_5212_RX_DESC_STATUS1_PHY_ERROR_CODE);
+			if (!ah->ah_capabilities.cap_has_phyerr_counters)
+				ath5k_ani_phy_error_report(ah, rs->rs_phyerr);
+		}
+
+		if (rxstat1 & AR5K_5212_RX_DESC_STATUS1_DECRYPT_CRC_ERROR)
+			rs->rs_status |= AR5K_RXERR_DECRYPT;
+
+		if (rxstat1 & AR5K_5212_RX_DESC_STATUS1_MIC_ERROR)
+			rs->rs_status |= AR5K_RXERR_MIC;
+	}
+	return 0;
+}
+
+
+/********\
+* Attach *
+\********/
+
+/**
+ * ath5k_hw_init_desc_functions() - Init function pointers inside ah
+ * @ah: The &struct ath5k_hw
+ *
+ * Maps the internal descriptor functions to the function pointers on ah, used
+ * from above. This is used as an abstraction layer to handle the various chips
+ * the same way.
+ */
+int
+ath5k_hw_init_desc_functions(struct ath5k_hw *ah)
+{
+	if (ah->ah_version == AR5K_AR5212) {
+		ah->ah_setup_tx_desc = ath5k_hw_setup_4word_tx_desc;
+		ah->ah_proc_tx_desc = ath5k_hw_proc_4word_tx_status;
+		ah->ah_proc_rx_desc = ath5k_hw_proc_5212_rx_status;
+	} else if (ah->ah_version <= AR5K_AR5211) {
+		ah->ah_setup_tx_desc = ath5k_hw_setup_2word_tx_desc;
+		ah->ah_proc_tx_desc = ath5k_hw_proc_2word_tx_status;
+		ah->ah_proc_rx_desc = ath5k_hw_proc_5210_rx_status;
+	} else
+		return -ENOTSUPP;
+	return 0;
+}

linux-7.2.3/drivers/net/wireless/ath/ath5k/desc.h

@@ -0,0 +1,367 @@
+/*
+ * Copyright (c) 2004-2008 Reyk Floeter <reyk@openbsd.org>
+ * Copyright (c) 2006-2008 Nick Kossifidis <mickflemm@gmail.com>
+ *
+ * Permission to use, copy, modify, and distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+/*
+ * RX/TX descriptor structures
+ */
+
+/**
+ * struct ath5k_hw_rx_ctl - Common hardware RX control descriptor
+ * @rx_control_0: RX control word 0
+ * @rx_control_1: RX control word 1
+ */
+struct ath5k_hw_rx_ctl {
+	u32	rx_control_0;
+	u32	rx_control_1;
+} __packed __aligned(4);
+
+/* RX control word 1 fields/flags */
+#define AR5K_DESC_RX_CTL1_BUF_LEN		0x00000fff /* data buffer length */
+#define AR5K_DESC_RX_CTL1_INTREQ		0x00002000 /* RX interrupt request */
+
+/**
+ * struct ath5k_hw_rx_status - Common hardware RX status descriptor
+ * @rx_status_0: RX status word 0
+ * @rx_status_1: RX status word 1
+ *
+ * 5210, 5211 and 5212 differ only in the fields and flags defined below
+ */
+struct ath5k_hw_rx_status {
+	u32	rx_status_0;
+	u32	rx_status_1;
+} __packed __aligned(4);
+
+/* 5210/5211 */
+/* RX status word 0 fields/flags */
+#define AR5K_5210_RX_DESC_STATUS0_DATA_LEN		0x00000fff /* RX data length */
+#define AR5K_5210_RX_DESC_STATUS0_MORE			0x00001000 /* more desc for this frame */
+#define AR5K_5210_RX_DESC_STATUS0_RECEIVE_ANT_5210	0x00004000 /* [5210] receive on ant 1 */
+#define AR5K_5210_RX_DESC_STATUS0_RECEIVE_RATE		0x00078000 /* reception rate */
+#define AR5K_5210_RX_DESC_STATUS0_RECEIVE_RATE_S	15
+#define AR5K_5210_RX_DESC_STATUS0_RECEIVE_SIGNAL	0x07f80000 /* rssi */
+#define AR5K_5210_RX_DESC_STATUS0_RECEIVE_SIGNAL_S	19
+#define AR5K_5210_RX_DESC_STATUS0_RECEIVE_ANT_5211	0x38000000 /* [5211] receive antenna */
+#define AR5K_5210_RX_DESC_STATUS0_RECEIVE_ANT_5211_S	27
+
+/* RX status word 1 fields/flags */
+#define AR5K_5210_RX_DESC_STATUS1_DONE			0x00000001 /* descriptor complete */
+#define AR5K_5210_RX_DESC_STATUS1_FRAME_RECEIVE_OK	0x00000002 /* reception success */
+#define AR5K_5210_RX_DESC_STATUS1_CRC_ERROR		0x00000004 /* CRC error */
+#define AR5K_5210_RX_DESC_STATUS1_FIFO_OVERRUN_5210	0x00000008 /* [5210] FIFO overrun */
+#define AR5K_5210_RX_DESC_STATUS1_DECRYPT_CRC_ERROR	0x00000010 /* decryption CRC failure */
+#define AR5K_5210_RX_DESC_STATUS1_PHY_ERROR		0x000000e0 /* PHY error */
+#define AR5K_5210_RX_DESC_STATUS1_PHY_ERROR_S		5
+#define AR5K_5210_RX_DESC_STATUS1_KEY_INDEX_VALID	0x00000100 /* key index valid */
+#define AR5K_5210_RX_DESC_STATUS1_KEY_INDEX		0x00007e00 /* decryption key index */
+#define AR5K_5210_RX_DESC_STATUS1_KEY_INDEX_S		9
+#define AR5K_5210_RX_DESC_STATUS1_RECEIVE_TIMESTAMP	0x0fff8000 /* 13 bit of TSF */
+#define AR5K_5210_RX_DESC_STATUS1_RECEIVE_TIMESTAMP_S	15
+#define AR5K_5210_RX_DESC_STATUS1_KEY_CACHE_MISS	0x10000000 /* key cache miss */
+
+/* 5212 */
+/* RX status word 0 fields/flags */
+#define AR5K_5212_RX_DESC_STATUS0_DATA_LEN		0x00000fff /* RX data length */
+#define AR5K_5212_RX_DESC_STATUS0_MORE			0x00001000 /* more desc for this frame */
+#define AR5K_5212_RX_DESC_STATUS0_DECOMP_CRC_ERROR	0x00002000 /* decompression CRC error */
+#define AR5K_5212_RX_DESC_STATUS0_RECEIVE_RATE		0x000f8000 /* reception rate */
+#define AR5K_5212_RX_DESC_STATUS0_RECEIVE_RATE_S	15
+#define AR5K_5212_RX_DESC_STATUS0_RECEIVE_SIGNAL	0x0ff00000 /* rssi */
+#define AR5K_5212_RX_DESC_STATUS0_RECEIVE_SIGNAL_S	20
+#define AR5K_5212_RX_DESC_STATUS0_RECEIVE_ANTENNA	0xf0000000 /* receive antenna */
+#define AR5K_5212_RX_DESC_STATUS0_RECEIVE_ANTENNA_S	28
+
+/* RX status word 1 fields/flags */
+#define AR5K_5212_RX_DESC_STATUS1_DONE			0x00000001 /* descriptor complete */
+#define AR5K_5212_RX_DESC_STATUS1_FRAME_RECEIVE_OK	0x00000002 /* frame reception success */
+#define AR5K_5212_RX_DESC_STATUS1_CRC_ERROR		0x00000004 /* CRC error */
+#define AR5K_5212_RX_DESC_STATUS1_DECRYPT_CRC_ERROR	0x00000008 /* decryption CRC failure */
+#define AR5K_5212_RX_DESC_STATUS1_PHY_ERROR		0x00000010 /* PHY error */
+#define AR5K_5212_RX_DESC_STATUS1_MIC_ERROR		0x00000020 /* MIC decrypt error */
+#define AR5K_5212_RX_DESC_STATUS1_KEY_INDEX_VALID	0x00000100 /* key index valid */
+#define AR5K_5212_RX_DESC_STATUS1_KEY_INDEX		0x0000fe00 /* decryption key index */
+#define AR5K_5212_RX_DESC_STATUS1_KEY_INDEX_S		9
+#define AR5K_5212_RX_DESC_STATUS1_RECEIVE_TIMESTAMP	0x7fff0000 /* first 15bit of the TSF */
+#define AR5K_5212_RX_DESC_STATUS1_RECEIVE_TIMESTAMP_S	16
+#define AR5K_5212_RX_DESC_STATUS1_KEY_CACHE_MISS	0x80000000 /* key cache miss */
+#define AR5K_5212_RX_DESC_STATUS1_PHY_ERROR_CODE	0x0000ff00 /* phy error code overlays key index and valid fields */
+#define AR5K_5212_RX_DESC_STATUS1_PHY_ERROR_CODE_S	8
+
+/**
+ * enum ath5k_phy_error_code - PHY Error codes
+ * @AR5K_RX_PHY_ERROR_UNDERRUN: Transmit underrun, [5210] No error
+ * @AR5K_RX_PHY_ERROR_TIMING: Timing error
+ * @AR5K_RX_PHY_ERROR_PARITY: Illegal parity
+ * @AR5K_RX_PHY_ERROR_RATE: Illegal rate
+ * @AR5K_RX_PHY_ERROR_LENGTH: Illegal length
+ * @AR5K_RX_PHY_ERROR_RADAR: Radar detect, [5210] 64 QAM rate
+ * @AR5K_RX_PHY_ERROR_SERVICE: Illegal service
+ * @AR5K_RX_PHY_ERROR_TOR: Transmit override receive
+ * @AR5K_RX_PHY_ERROR_OFDM_TIMING: OFDM Timing error [5212+]
+ * @AR5K_RX_PHY_ERROR_OFDM_SIGNAL_PARITY: OFDM Signal parity error [5212+]
+ * @AR5K_RX_PHY_ERROR_OFDM_RATE_ILLEGAL: OFDM Illegal rate [5212+]
+ * @AR5K_RX_PHY_ERROR_OFDM_LENGTH_ILLEGAL: OFDM Illegal length [5212+]
+ * @AR5K_RX_PHY_ERROR_OFDM_POWER_DROP: OFDM Power drop [5212+]
+ * @AR5K_RX_PHY_ERROR_OFDM_SERVICE: OFDM Service (?) [5212+]
+ * @AR5K_RX_PHY_ERROR_OFDM_RESTART: OFDM Restart (?) [5212+]
+ * @AR5K_RX_PHY_ERROR_CCK_TIMING: CCK Timing error [5212+]
+ * @AR5K_RX_PHY_ERROR_CCK_HEADER_CRC: Header CRC error [5212+]
+ * @AR5K_RX_PHY_ERROR_CCK_RATE_ILLEGAL: Illegal rate [5212+]
+ * @AR5K_RX_PHY_ERROR_CCK_SERVICE: CCK Service (?) [5212+]
+ * @AR5K_RX_PHY_ERROR_CCK_RESTART: CCK Restart (?) [5212+]
+ */
+enum ath5k_phy_error_code {
+	AR5K_RX_PHY_ERROR_UNDERRUN		= 0,
+	AR5K_RX_PHY_ERROR_TIMING		= 1,
+	AR5K_RX_PHY_ERROR_PARITY		= 2,
+	AR5K_RX_PHY_ERROR_RATE			= 3,
+	AR5K_RX_PHY_ERROR_LENGTH		= 4,
+	AR5K_RX_PHY_ERROR_RADAR			= 5,
+	AR5K_RX_PHY_ERROR_SERVICE		= 6,
+	AR5K_RX_PHY_ERROR_TOR			= 7,
+	AR5K_RX_PHY_ERROR_OFDM_TIMING		= 17,
+	AR5K_RX_PHY_ERROR_OFDM_SIGNAL_PARITY	= 18,
+	AR5K_RX_PHY_ERROR_OFDM_RATE_ILLEGAL	= 19,
+	AR5K_RX_PHY_ERROR_OFDM_LENGTH_ILLEGAL	= 20,
+	AR5K_RX_PHY_ERROR_OFDM_POWER_DROP	= 21,
+	AR5K_RX_PHY_ERROR_OFDM_SERVICE		= 22,
+	AR5K_RX_PHY_ERROR_OFDM_RESTART		= 23,
+	AR5K_RX_PHY_ERROR_CCK_TIMING		= 25,
+	AR5K_RX_PHY_ERROR_CCK_HEADER_CRC	= 26,
+	AR5K_RX_PHY_ERROR_CCK_RATE_ILLEGAL	= 27,
+	AR5K_RX_PHY_ERROR_CCK_SERVICE		= 30,
+	AR5K_RX_PHY_ERROR_CCK_RESTART		= 31,
+};
+
+/**
+ * struct ath5k_hw_2w_tx_ctl  - 5210/5211 hardware 2-word TX control descriptor
+ * @tx_control_0: TX control word 0
+ * @tx_control_1: TX control word 1
+ */
+struct ath5k_hw_2w_tx_ctl {
+	u32	tx_control_0;
+	u32	tx_control_1;
+} __packed __aligned(4);
+
+/* TX control word 0 fields/flags */
+#define AR5K_2W_TX_DESC_CTL0_FRAME_LEN		0x00000fff /* frame length */
+#define AR5K_2W_TX_DESC_CTL0_HEADER_LEN_5210	0x0003f000 /* [5210] header length */
+#define AR5K_2W_TX_DESC_CTL0_HEADER_LEN_5210_S	12
+#define AR5K_2W_TX_DESC_CTL0_XMIT_RATE		0x003c0000 /* tx rate */
+#define AR5K_2W_TX_DESC_CTL0_XMIT_RATE_S	18
+#define AR5K_2W_TX_DESC_CTL0_RTSENA		0x00400000 /* RTS/CTS enable */
+#define AR5K_2W_TX_DESC_CTL0_LONG_PACKET_5210	0x00800000 /* [5210] long packet */
+#define AR5K_2W_TX_DESC_CTL0_VEOL_5211		0x00800000 /* [5211] virtual end-of-list */
+#define AR5K_2W_TX_DESC_CTL0_CLRDMASK		0x01000000 /* clear destination mask */
+#define AR5K_2W_TX_DESC_CTL0_ANT_MODE_XMIT_5210	0x02000000 /* [5210] antenna selection */
+#define AR5K_2W_TX_DESC_CTL0_ANT_MODE_XMIT_5211	0x1e000000 /* [5211] antenna selection */
+#define AR5K_2W_TX_DESC_CTL0_ANT_MODE_XMIT			\
+		(ah->ah_version == AR5K_AR5210 ?		\
+		AR5K_2W_TX_DESC_CTL0_ANT_MODE_XMIT_5210 :	\
+		AR5K_2W_TX_DESC_CTL0_ANT_MODE_XMIT_5211)
+#define AR5K_2W_TX_DESC_CTL0_ANT_MODE_XMIT_S	25
+#define AR5K_2W_TX_DESC_CTL0_FRAME_TYPE_5210	0x1c000000 /* [5210] frame type */
+#define AR5K_2W_TX_DESC_CTL0_FRAME_TYPE_5210_S	26
+#define AR5K_2W_TX_DESC_CTL0_INTREQ		0x20000000 /* TX interrupt request */
+#define AR5K_2W_TX_DESC_CTL0_ENCRYPT_KEY_VALID	0x40000000 /* key is valid */
+
+/* TX control word 1 fields/flags */
+#define AR5K_2W_TX_DESC_CTL1_BUF_LEN		0x00000fff /* data buffer length */
+#define AR5K_2W_TX_DESC_CTL1_MORE		0x00001000 /* more desc for this frame */
+#define AR5K_2W_TX_DESC_CTL1_ENC_KEY_IDX_5210	0x0007e000 /* [5210] key table index */
+#define AR5K_2W_TX_DESC_CTL1_ENC_KEY_IDX_5211	0x000fe000 /* [5211] key table index */
+#define AR5K_2W_TX_DESC_CTL1_ENC_KEY_IDX				\
+			(ah->ah_version == AR5K_AR5210 ?		\
+			AR5K_2W_TX_DESC_CTL1_ENC_KEY_IDX_5210 :		\
+			AR5K_2W_TX_DESC_CTL1_ENC_KEY_IDX_5211)
+#define AR5K_2W_TX_DESC_CTL1_ENC_KEY_IDX_S	13
+#define AR5K_2W_TX_DESC_CTL1_FRAME_TYPE_5211	0x00700000 /* [5211] frame type */
+#define AR5K_2W_TX_DESC_CTL1_FRAME_TYPE_5211_S	20
+#define AR5K_2W_TX_DESC_CTL1_NOACK_5211		0x00800000 /* [5211] no ACK */
+#define AR5K_2W_TX_DESC_CTL1_RTS_DURATION_5210	0xfff80000 /* [5210] lower 13 bit of duration */
+
+/* Frame types */
+#define AR5K_AR5210_TX_DESC_FRAME_TYPE_NORMAL	0
+#define AR5K_AR5210_TX_DESC_FRAME_TYPE_ATIM	1
+#define AR5K_AR5210_TX_DESC_FRAME_TYPE_PSPOLL	2
+#define AR5K_AR5210_TX_DESC_FRAME_TYPE_NO_DELAY	3
+#define AR5K_AR5211_TX_DESC_FRAME_TYPE_BEACON	3
+#define AR5K_AR5210_TX_DESC_FRAME_TYPE_PIFS	4
+#define AR5K_AR5211_TX_DESC_FRAME_TYPE_PRESP	4
+
+/**
+ * struct ath5k_hw_4w_tx_ctl - 5212 hardware 4-word TX control descriptor
+ * @tx_control_0: TX control word 0
+ * @tx_control_1: TX control word 1
+ * @tx_control_2: TX control word 2
+ * @tx_control_3: TX control word 3
+ */
+struct ath5k_hw_4w_tx_ctl {
+	u32	tx_control_0;
+	u32	tx_control_1;
+	u32	tx_control_2;
+	u32	tx_control_3;
+} __packed __aligned(4);
+
+/* TX control word 0 fields/flags */
+#define AR5K_4W_TX_DESC_CTL0_FRAME_LEN		0x00000fff /* frame length */
+#define AR5K_4W_TX_DESC_CTL0_XMIT_POWER		0x003f0000 /* transmit power */
+#define AR5K_4W_TX_DESC_CTL0_XMIT_POWER_S	16
+#define AR5K_4W_TX_DESC_CTL0_RTSENA		0x00400000 /* RTS/CTS enable */
+#define AR5K_4W_TX_DESC_CTL0_VEOL		0x00800000 /* virtual end-of-list */
+#define AR5K_4W_TX_DESC_CTL0_CLRDMASK		0x01000000 /* clear destination mask */
+#define AR5K_4W_TX_DESC_CTL0_ANT_MODE_XMIT	0x1e000000 /* TX antenna selection */
+#define AR5K_4W_TX_DESC_CTL0_ANT_MODE_XMIT_S	25
+#define AR5K_4W_TX_DESC_CTL0_INTREQ		0x20000000 /* TX interrupt request */
+#define AR5K_4W_TX_DESC_CTL0_ENCRYPT_KEY_VALID	0x40000000 /* destination index valid */
+#define AR5K_4W_TX_DESC_CTL0_CTSENA		0x80000000 /* precede frame with CTS */
+
+/* TX control word 1 fields/flags */
+#define AR5K_4W_TX_DESC_CTL1_BUF_LEN		0x00000fff /* data buffer length */
+#define AR5K_4W_TX_DESC_CTL1_MORE		0x00001000 /* more desc for this frame */
+#define AR5K_4W_TX_DESC_CTL1_ENCRYPT_KEY_IDX	0x000fe000 /* destination table index */
+#define AR5K_4W_TX_DESC_CTL1_ENCRYPT_KEY_IDX_S	13
+#define AR5K_4W_TX_DESC_CTL1_FRAME_TYPE		0x00f00000 /* frame type */
+#define AR5K_4W_TX_DESC_CTL1_FRAME_TYPE_S	20
+#define AR5K_4W_TX_DESC_CTL1_NOACK		0x01000000 /* no ACK */
+#define AR5K_4W_TX_DESC_CTL1_COMP_PROC		0x06000000 /* compression processing */
+#define AR5K_4W_TX_DESC_CTL1_COMP_PROC_S	25
+#define AR5K_4W_TX_DESC_CTL1_COMP_IV_LEN	0x18000000 /* length of frame IV */
+#define AR5K_4W_TX_DESC_CTL1_COMP_IV_LEN_S	27
+#define AR5K_4W_TX_DESC_CTL1_COMP_ICV_LEN	0x60000000 /* length of frame ICV */
+#define AR5K_4W_TX_DESC_CTL1_COMP_ICV_LEN_S	29
+
+/* TX control word 2 fields/flags */
+#define AR5K_4W_TX_DESC_CTL2_RTS_DURATION	0x00007fff /* RTS/CTS duration */
+#define AR5K_4W_TX_DESC_CTL2_DURATION_UPD_EN	0x00008000 /* frame duration update */
+#define AR5K_4W_TX_DESC_CTL2_XMIT_TRIES0	0x000f0000 /* series 0 max attempts */
+#define AR5K_4W_TX_DESC_CTL2_XMIT_TRIES0_S	16
+#define AR5K_4W_TX_DESC_CTL2_XMIT_TRIES1	0x00f00000 /* series 1 max attempts */
+#define AR5K_4W_TX_DESC_CTL2_XMIT_TRIES1_S	20
+#define AR5K_4W_TX_DESC_CTL2_XMIT_TRIES2	0x0f000000 /* series 2 max attempts */
+#define AR5K_4W_TX_DESC_CTL2_XMIT_TRIES2_S	24
+#define AR5K_4W_TX_DESC_CTL2_XMIT_TRIES3	0xf0000000 /* series 3 max attempts */
+#define AR5K_4W_TX_DESC_CTL2_XMIT_TRIES3_S	28
+
+/* TX control word 3 fields/flags */
+#define AR5K_4W_TX_DESC_CTL3_XMIT_RATE0		0x0000001f /* series 0 tx rate */
+#define AR5K_4W_TX_DESC_CTL3_XMIT_RATE1		0x000003e0 /* series 1 tx rate */
+#define AR5K_4W_TX_DESC_CTL3_XMIT_RATE1_S	5
+#define AR5K_4W_TX_DESC_CTL3_XMIT_RATE2		0x00007c00 /* series 2 tx rate */
+#define AR5K_4W_TX_DESC_CTL3_XMIT_RATE2_S	10
+#define AR5K_4W_TX_DESC_CTL3_XMIT_RATE3		0x000f8000 /* series 3 tx rate */
+#define AR5K_4W_TX_DESC_CTL3_XMIT_RATE3_S	15
+#define AR5K_4W_TX_DESC_CTL3_RTS_CTS_RATE	0x01f00000 /* RTS or CTS rate */
+#define AR5K_4W_TX_DESC_CTL3_RTS_CTS_RATE_S	20
+
+/**
+ * struct ath5k_hw_tx_status - Common TX status descriptor
+ * @tx_status_0: TX status word 0
+ * @tx_status_1: TX status word 1
+ */
+struct ath5k_hw_tx_status {
+	u32	tx_status_0;
+	u32	tx_status_1;
+} __packed __aligned(4);
+
+/* TX status word 0 fields/flags */
+#define AR5K_DESC_TX_STATUS0_FRAME_XMIT_OK	0x00000001 /* TX success */
+#define AR5K_DESC_TX_STATUS0_EXCESSIVE_RETRIES	0x00000002 /* excessive retries */
+#define AR5K_DESC_TX_STATUS0_FIFO_UNDERRUN	0x00000004 /* FIFO underrun */
+#define AR5K_DESC_TX_STATUS0_FILTERED		0x00000008 /* TX filter indication */
+/* according to the HAL sources the spec has short/long retry counts reversed.
+ * we have it reversed to the HAL sources as well, for 5210 and 5211.
+ * For 5212 these fields are defined as RTS_FAIL_COUNT and DATA_FAIL_COUNT,
+ * but used respectively as SHORT and LONG retry count in the code later. This
+ * is consistent with the definitions here... TODO: check */
+#define AR5K_DESC_TX_STATUS0_SHORT_RETRY_COUNT	0x000000f0 /* short retry count */
+#define AR5K_DESC_TX_STATUS0_SHORT_RETRY_COUNT_S	4
+#define AR5K_DESC_TX_STATUS0_LONG_RETRY_COUNT	0x00000f00 /* long retry count */
+#define AR5K_DESC_TX_STATUS0_LONG_RETRY_COUNT_S	8
+#define AR5K_DESC_TX_STATUS0_VIRTCOLL_CT_5211	0x0000f000 /* [5211+] virtual collision count */
+#define AR5K_DESC_TX_STATUS0_VIRTCOLL_CT_5212_S	12
+#define AR5K_DESC_TX_STATUS0_SEND_TIMESTAMP	0xffff0000 /* TX timestamp */
+#define AR5K_DESC_TX_STATUS0_SEND_TIMESTAMP_S	16
+
+/* TX status word 1 fields/flags */
+#define AR5K_DESC_TX_STATUS1_DONE		0x00000001 /* descriptor complete */
+#define AR5K_DESC_TX_STATUS1_SEQ_NUM		0x00001ffe /* TX sequence number */
+#define AR5K_DESC_TX_STATUS1_SEQ_NUM_S		1
+#define AR5K_DESC_TX_STATUS1_ACK_SIG_STRENGTH	0x001fe000 /* signal strength of ACK */
+#define AR5K_DESC_TX_STATUS1_ACK_SIG_STRENGTH_S	13
+#define AR5K_DESC_TX_STATUS1_FINAL_TS_IX_5212	0x00600000 /* [5212] final TX attempt series ix */
+#define AR5K_DESC_TX_STATUS1_FINAL_TS_IX_5212_S	21
+#define AR5K_DESC_TX_STATUS1_COMP_SUCCESS_5212	0x00800000 /* [5212] compression status */
+#define AR5K_DESC_TX_STATUS1_XMIT_ANTENNA_5212	0x01000000 /* [5212] transmit antenna */
+
+/**
+ * struct ath5k_hw_5210_tx_desc - 5210/5211 hardware TX descriptor
+ * @tx_ctl: The &struct ath5k_hw_2w_tx_ctl
+ * @tx_stat: The &struct ath5k_hw_tx_status
+ */
+struct ath5k_hw_5210_tx_desc {
+	struct ath5k_hw_2w_tx_ctl	tx_ctl;
+	struct ath5k_hw_tx_status	tx_stat;
+} __packed __aligned(4);
+
+/**
+ * struct ath5k_hw_5212_tx_desc - 5212 hardware TX descriptor
+ * @tx_ctl: The &struct ath5k_hw_4w_tx_ctl
+ * @tx_stat: The &struct ath5k_hw_tx_status
+ */
+struct ath5k_hw_5212_tx_desc {
+	struct ath5k_hw_4w_tx_ctl	tx_ctl;
+	struct ath5k_hw_tx_status	tx_stat;
+} __packed __aligned(4);
+
+/**
+ * struct ath5k_hw_all_rx_desc - Common hardware RX descriptor
+ * @rx_ctl: The &struct ath5k_hw_rx_ctl
+ * @rx_stat: The &struct ath5k_hw_rx_status
+ */
+struct ath5k_hw_all_rx_desc {
+	struct ath5k_hw_rx_ctl		rx_ctl;
+	struct ath5k_hw_rx_status	rx_stat;
+} __packed __aligned(4);
+
+/**
+ * struct ath5k_desc - Atheros hardware DMA descriptor
+ * @ds_link: Physical address of the next descriptor
+ * @ds_data: Physical address of data buffer (skb)
+ * @ud: Union containing hw_5xxx_tx_desc structs and hw_all_rx_desc
+ *
+ * This is read and written to by the hardware
+ */
+struct ath5k_desc {
+	u32	ds_link;
+	u32	ds_data;
+
+	union {
+		struct ath5k_hw_5210_tx_desc	ds_tx5210;
+		struct ath5k_hw_5212_tx_desc	ds_tx5212;
+		struct ath5k_hw_all_rx_desc	ds_rx;
+	} ud;
+} __packed __aligned(4);
+
+#define AR5K_RXDESC_INTREQ	0x0020
+
+#define AR5K_TXDESC_CLRDMASK	0x0001
+#define AR5K_TXDESC_NOACK	0x0002	/*[5211+]*/
+#define AR5K_TXDESC_RTSENA	0x0004
+#define AR5K_TXDESC_CTSENA	0x0008
+#define AR5K_TXDESC_INTREQ	0x0010
+#define AR5K_TXDESC_VEOL	0x0020	/*[5211+]*/

linux-7.2.3/drivers/net/wireless/ath/ath5k/dma.c

@@ -0,0 +1,913 @@
+/*
+ * Copyright (c) 2004-2008 Reyk Floeter <reyk@openbsd.org>
+ * Copyright (c) 2006-2008 Nick Kossifidis <mickflemm@gmail.com>
+ *
+ * Permission to use, copy, modify, and distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+/*************************************\
+* DMA and interrupt masking functions *
+\*************************************/
+
+/**
+ * DOC: DMA and interrupt masking functions
+ *
+ * Here we setup descriptor pointers (rxdp/txdp) start/stop dma engine and
+ * handle queue setup for 5210 chipset (rest are handled on qcu.c).
+ * Also we setup interrupt mask register (IMR) and read the various interrupt
+ * status registers (ISR).
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include "ath5k.h"
+#include "reg.h"
+#include "debug.h"
+
+
+/*********\
+* Receive *
+\*********/
+
+/**
+ * ath5k_hw_start_rx_dma() - Start DMA receive
+ * @ah:	The &struct ath5k_hw
+ */
+void
+ath5k_hw_start_rx_dma(struct ath5k_hw *ah)
+{
+	ath5k_hw_reg_write(ah, AR5K_CR_RXE, AR5K_CR);
+	ath5k_hw_reg_read(ah, AR5K_CR);
+}
+
+/**
+ * ath5k_hw_stop_rx_dma() - Stop DMA receive
+ * @ah:	The &struct ath5k_hw
+ */
+static int
+ath5k_hw_stop_rx_dma(struct ath5k_hw *ah)
+{
+	unsigned int i;
+
+	ath5k_hw_reg_write(ah, AR5K_CR_RXD, AR5K_CR);
+
+	/*
+	 * It may take some time to disable the DMA receive unit
+	 */
+	for (i = 1000; i > 0 &&
+			(ath5k_hw_reg_read(ah, AR5K_CR) & AR5K_CR_RXE) != 0;
+			i--)
+		udelay(100);
+
+	if (!i)
+		ATH5K_DBG(ah, ATH5K_DEBUG_DMA,
+				"failed to stop RX DMA !\n");
+
+	return i ? 0 : -EBUSY;
+}
+
+/**
+ * ath5k_hw_get_rxdp() - Get RX Descriptor's address
+ * @ah: The &struct ath5k_hw
+ */
+u32
+ath5k_hw_get_rxdp(struct ath5k_hw *ah)
+{
+	return ath5k_hw_reg_read(ah, AR5K_RXDP);
+}
+
+/**
+ * ath5k_hw_set_rxdp() - Set RX Descriptor's address
+ * @ah: The &struct ath5k_hw
+ * @phys_addr: RX descriptor address
+ *
+ * Returns -EIO if rx is active
+ */
+int
+ath5k_hw_set_rxdp(struct ath5k_hw *ah, u32 phys_addr)
+{
+	if (ath5k_hw_reg_read(ah, AR5K_CR) & AR5K_CR_RXE) {
+		ATH5K_DBG(ah, ATH5K_DEBUG_DMA,
+				"tried to set RXDP while rx was active !\n");
+		return -EIO;
+	}
+
+	ath5k_hw_reg_write(ah, phys_addr, AR5K_RXDP);
+	return 0;
+}
+
+
+/**********\
+* Transmit *
+\**********/
+
+/**
+ * ath5k_hw_start_tx_dma() - Start DMA transmit for a specific queue
+ * @ah: The &struct ath5k_hw
+ * @queue: The hw queue number
+ *
+ * Start DMA transmit for a specific queue and since 5210 doesn't have
+ * QCU/DCU, set up queue parameters for 5210 here based on queue type (one
+ * queue for normal data and one queue for beacons). For queue setup
+ * on newer chips check out qcu.c. Returns -EINVAL if queue number is out
+ * of range or if queue is already disabled.
+ *
+ * NOTE: Must be called after setting up tx control descriptor for that
+ * queue (see below).
+ */
+int
+ath5k_hw_start_tx_dma(struct ath5k_hw *ah, unsigned int queue)
+{
+	u32 tx_queue;
+
+	AR5K_ASSERT_ENTRY(queue, ah->ah_capabilities.cap_queues.q_tx_num);
+
+	/* Return if queue is declared inactive */
+	if (ah->ah_txq[queue].tqi_type == AR5K_TX_QUEUE_INACTIVE)
+		return -EINVAL;
+
+	if (ah->ah_version == AR5K_AR5210) {
+		tx_queue = ath5k_hw_reg_read(ah, AR5K_CR);
+
+		/*
+		 * Set the queue by type on 5210
+		 */
+		switch (ah->ah_txq[queue].tqi_type) {
+		case AR5K_TX_QUEUE_DATA:
+			tx_queue |= AR5K_CR_TXE0 & ~AR5K_CR_TXD0;
+			break;
+		case AR5K_TX_QUEUE_BEACON:
+			tx_queue |= AR5K_CR_TXE1 & ~AR5K_CR_TXD1;
+			ath5k_hw_reg_write(ah, AR5K_BCR_TQ1V | AR5K_BCR_BDMAE,
+					AR5K_BSR);
+			break;
+		case AR5K_TX_QUEUE_CAB:
+			tx_queue |= AR5K_CR_TXE1 & ~AR5K_CR_TXD1;
+			ath5k_hw_reg_write(ah, AR5K_BCR_TQ1FV | AR5K_BCR_TQ1V |
+				AR5K_BCR_BDMAE, AR5K_BSR);
+			break;
+		default:
+			return -EINVAL;
+		}
+		/* Start queue */
+		ath5k_hw_reg_write(ah, tx_queue, AR5K_CR);
+		ath5k_hw_reg_read(ah, AR5K_CR);
+	} else {
+		/* Return if queue is disabled */
+		if (AR5K_REG_READ_Q(ah, AR5K_QCU_TXD, queue))
+			return -EIO;
+
+		/* Start queue */
+		AR5K_REG_WRITE_Q(ah, AR5K_QCU_TXE, queue);
+	}
+
+	return 0;
+}
+
+/**
+ * ath5k_hw_stop_tx_dma() - Stop DMA transmit on a specific queue
+ * @ah: The &struct ath5k_hw
+ * @queue: The hw queue number
+ *
+ * Stop DMA transmit on a specific hw queue and drain queue so we don't
+ * have any pending frames. Returns -EBUSY if we still have pending frames,
+ * -EINVAL if queue number is out of range or inactive.
+ */
+static int
+ath5k_hw_stop_tx_dma(struct ath5k_hw *ah, unsigned int queue)
+{
+	unsigned int i = 40;
+	u32 tx_queue, pending;
+
+	AR5K_ASSERT_ENTRY(queue, ah->ah_capabilities.cap_queues.q_tx_num);
+
+	/* Return if queue is declared inactive */
+	if (ah->ah_txq[queue].tqi_type == AR5K_TX_QUEUE_INACTIVE)
+		return -EINVAL;
+
+	if (ah->ah_version == AR5K_AR5210) {
+		tx_queue = ath5k_hw_reg_read(ah, AR5K_CR);
+
+		/*
+		 * Set by queue type
+		 */
+		switch (ah->ah_txq[queue].tqi_type) {
+		case AR5K_TX_QUEUE_DATA:
+			tx_queue |= AR5K_CR_TXD0 & ~AR5K_CR_TXE0;
+			break;
+		case AR5K_TX_QUEUE_BEACON:
+		case AR5K_TX_QUEUE_CAB:
+			/* XXX Fix me... */
+			tx_queue |= AR5K_CR_TXD1 & ~AR5K_CR_TXD1;
+			ath5k_hw_reg_write(ah, 0, AR5K_BSR);
+			break;
+		default:
+			return -EINVAL;
+		}
+
+		/* Stop queue */
+		ath5k_hw_reg_write(ah, tx_queue, AR5K_CR);
+		ath5k_hw_reg_read(ah, AR5K_CR);
+	} else {
+
+		/*
+		 * Enable DCU early termination to quickly
+		 * flush any pending frames from QCU
+		 */
+		AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_MISC(queue),
+					AR5K_QCU_MISC_DCU_EARLY);
+
+		/*
+		 * Schedule TX disable and wait until queue is empty
+		 */
+		AR5K_REG_WRITE_Q(ah, AR5K_QCU_TXD, queue);
+
+		/* Wait for queue to stop */
+		for (i = 1000; i > 0 &&
+		(AR5K_REG_READ_Q(ah, AR5K_QCU_TXE, queue) != 0);
+		i--)
+			udelay(100);
+
+		if (AR5K_REG_READ_Q(ah, AR5K_QCU_TXE, queue))
+			ATH5K_DBG(ah, ATH5K_DEBUG_DMA,
+				"queue %i didn't stop !\n", queue);
+
+		/* Check for pending frames */
+		i = 1000;
+		do {
+			pending = ath5k_hw_reg_read(ah,
+				AR5K_QUEUE_STATUS(queue)) &
+				AR5K_QCU_STS_FRMPENDCNT;
+			udelay(100);
+		} while (--i && pending);
+
+		/* For 2413+ order PCU to drop packets using
+		 * QUIET mechanism */
+		if (ah->ah_mac_version >= (AR5K_SREV_AR2414 >> 4) &&
+		    pending) {
+			/* Set periodicity and duration */
+			ath5k_hw_reg_write(ah,
+				AR5K_REG_SM(100, AR5K_QUIET_CTL2_QT_PER)|
+				AR5K_REG_SM(10, AR5K_QUIET_CTL2_QT_DUR),
+				AR5K_QUIET_CTL2);
+
+			/* Enable quiet period for current TSF */
+			ath5k_hw_reg_write(ah,
+				AR5K_QUIET_CTL1_QT_EN |
+				AR5K_REG_SM(ath5k_hw_reg_read(ah,
+						AR5K_TSF_L32_5211) >> 10,
+						AR5K_QUIET_CTL1_NEXT_QT_TSF),
+				AR5K_QUIET_CTL1);
+
+			/* Force channel idle high */
+			AR5K_REG_ENABLE_BITS(ah, AR5K_DIAG_SW_5211,
+					AR5K_DIAG_SW_CHANNEL_IDLE_HIGH);
+
+			/* Wait a while and disable mechanism */
+			udelay(400);
+			AR5K_REG_DISABLE_BITS(ah, AR5K_QUIET_CTL1,
+						AR5K_QUIET_CTL1_QT_EN);
+
+			/* Re-check for pending frames */
+			i = 100;
+			do {
+				pending = ath5k_hw_reg_read(ah,
+					AR5K_QUEUE_STATUS(queue)) &
+					AR5K_QCU_STS_FRMPENDCNT;
+				udelay(100);
+			} while (--i && pending);
+
+			AR5K_REG_DISABLE_BITS(ah, AR5K_DIAG_SW_5211,
+					AR5K_DIAG_SW_CHANNEL_IDLE_HIGH);
+
+			if (pending)
+				ATH5K_DBG(ah, ATH5K_DEBUG_DMA,
+					"quiet mechanism didn't work q:%i !\n",
+					queue);
+		}
+
+		/*
+		 * Disable DCU early termination
+		 */
+		AR5K_REG_DISABLE_BITS(ah, AR5K_QUEUE_MISC(queue),
+					AR5K_QCU_MISC_DCU_EARLY);
+
+		/* Clear register */
+		ath5k_hw_reg_write(ah, 0, AR5K_QCU_TXD);
+		if (pending) {
+			ATH5K_DBG(ah, ATH5K_DEBUG_DMA,
+					"tx dma didn't stop (q:%i, frm:%i) !\n",
+					queue, pending);
+			return -EBUSY;
+		}
+	}
+
+	/* TODO: Check for success on 5210 else return error */
+	return 0;
+}
+
+/**
+ * ath5k_hw_stop_beacon_queue() - Stop beacon queue
+ * @ah: The &struct ath5k_hw
+ * @queue: The queue number
+ *
+ * Returns -EIO if queue didn't stop
+ */
+int
+ath5k_hw_stop_beacon_queue(struct ath5k_hw *ah, unsigned int queue)
+{
+	int ret;
+	ret = ath5k_hw_stop_tx_dma(ah, queue);
+	if (ret) {
+		ATH5K_DBG(ah, ATH5K_DEBUG_DMA,
+				"beacon queue didn't stop !\n");
+		return -EIO;
+	}
+	return 0;
+}
+
+/**
+ * ath5k_hw_get_txdp() - Get TX Descriptor's address for a specific queue
+ * @ah: The &struct ath5k_hw
+ * @queue: The hw queue number
+ *
+ * Get TX descriptor's address for a specific queue. For 5210 we ignore
+ * the queue number and use tx queue type since we only have 2 queues.
+ * We use TXDP0 for normal data queue and TXDP1 for beacon queue.
+ * For newer chips with QCU/DCU we just read the corresponding TXDP register.
+ *
+ * XXX: Is TXDP read and clear ?
+ */
+u32
+ath5k_hw_get_txdp(struct ath5k_hw *ah, unsigned int queue)
+{
+	u16 tx_reg;
+
+	AR5K_ASSERT_ENTRY(queue, ah->ah_capabilities.cap_queues.q_tx_num);
+
+	/*
+	 * Get the transmit queue descriptor pointer from the selected queue
+	 */
+	/*5210 doesn't have QCU*/
+	if (ah->ah_version == AR5K_AR5210) {
+		switch (ah->ah_txq[queue].tqi_type) {
+		case AR5K_TX_QUEUE_DATA:
+			tx_reg = AR5K_NOQCU_TXDP0;
+			break;
+		case AR5K_TX_QUEUE_BEACON:
+		case AR5K_TX_QUEUE_CAB:
+			tx_reg = AR5K_NOQCU_TXDP1;
+			break;
+		default:
+			return 0xffffffff;
+		}
+	} else {
+		tx_reg = AR5K_QUEUE_TXDP(queue);
+	}
+
+	return ath5k_hw_reg_read(ah, tx_reg);
+}
+
+/**
+ * ath5k_hw_set_txdp() - Set TX Descriptor's address for a specific queue
+ * @ah: The &struct ath5k_hw
+ * @queue: The hw queue number
+ * @phys_addr: The physical address
+ *
+ * Set TX descriptor's address for a specific queue. For 5210 we ignore
+ * the queue number and we use tx queue type since we only have 2 queues
+ * so as above we use TXDP0 for normal data queue and TXDP1 for beacon queue.
+ * For newer chips with QCU/DCU we just set the corresponding TXDP register.
+ * Returns -EINVAL if queue type is invalid for 5210 and -EIO if queue is still
+ * active.
+ */
+int
+ath5k_hw_set_txdp(struct ath5k_hw *ah, unsigned int queue, u32 phys_addr)
+{
+	u16 tx_reg;
+
+	AR5K_ASSERT_ENTRY(queue, ah->ah_capabilities.cap_queues.q_tx_num);
+
+	/*
+	 * Set the transmit queue descriptor pointer register by type
+	 * on 5210
+	 */
+	if (ah->ah_version == AR5K_AR5210) {
+		switch (ah->ah_txq[queue].tqi_type) {
+		case AR5K_TX_QUEUE_DATA:
+			tx_reg = AR5K_NOQCU_TXDP0;
+			break;
+		case AR5K_TX_QUEUE_BEACON:
+		case AR5K_TX_QUEUE_CAB:
+			tx_reg = AR5K_NOQCU_TXDP1;
+			break;
+		default:
+			return -EINVAL;
+		}
+	} else {
+		/*
+		 * Set the transmit queue descriptor pointer for
+		 * the selected queue on QCU for 5211+
+		 * (this won't work if the queue is still active)
+		 */
+		if (AR5K_REG_READ_Q(ah, AR5K_QCU_TXE, queue))
+			return -EIO;
+
+		tx_reg = AR5K_QUEUE_TXDP(queue);
+	}
+
+	/* Set descriptor pointer */
+	ath5k_hw_reg_write(ah, phys_addr, tx_reg);
+
+	return 0;
+}
+
+/**
+ * ath5k_hw_update_tx_triglevel() - Update tx trigger level
+ * @ah: The &struct ath5k_hw
+ * @increase: Flag to force increase of trigger level
+ *
+ * This function increases/decreases the tx trigger level for the tx fifo
+ * buffer (aka FIFO threshold) that is used to indicate when PCU flushes
+ * the buffer and transmits its data. Lowering this results sending small
+ * frames more quickly but can lead to tx underruns, raising it a lot can
+ * result other problems. Right now we start with the lowest possible
+ * (64Bytes) and if we get tx underrun we increase it using the increase
+ * flag. Returns -EIO if we have reached maximum/minimum.
+ *
+ * XXX: Link this with tx DMA size ?
+ * XXX2: Use it to save interrupts ?
+ */
+int
+ath5k_hw_update_tx_triglevel(struct ath5k_hw *ah, bool increase)
+{
+	u32 trigger_level, imr;
+	int ret = -EIO;
+
+	/*
+	 * Disable interrupts by setting the mask
+	 */
+	imr = ath5k_hw_set_imr(ah, ah->ah_imr & ~AR5K_INT_GLOBAL);
+
+	trigger_level = AR5K_REG_MS(ath5k_hw_reg_read(ah, AR5K_TXCFG),
+			AR5K_TXCFG_TXFULL);
+
+	if (!increase) {
+		if (--trigger_level < AR5K_TUNE_MIN_TX_FIFO_THRES)
+			goto done;
+	} else
+		trigger_level +=
+			((AR5K_TUNE_MAX_TX_FIFO_THRES - trigger_level) / 2);
+
+	/*
+	 * Update trigger level on success
+	 */
+	if (ah->ah_version == AR5K_AR5210)
+		ath5k_hw_reg_write(ah, trigger_level, AR5K_TRIG_LVL);
+	else
+		AR5K_REG_WRITE_BITS(ah, AR5K_TXCFG,
+				AR5K_TXCFG_TXFULL, trigger_level);
+
+	ret = 0;
+
+done:
+	/*
+	 * Restore interrupt mask
+	 */
+	ath5k_hw_set_imr(ah, imr);
+
+	return ret;
+}
+
+
+/*******************\
+* Interrupt masking *
+\*******************/
+
+/**
+ * ath5k_hw_is_intr_pending() - Check if we have pending interrupts
+ * @ah: The &struct ath5k_hw
+ *
+ * Check if we have pending interrupts to process. Returns 1 if we
+ * have pending interrupts and 0 if we haven't.
+ */
+bool
+ath5k_hw_is_intr_pending(struct ath5k_hw *ah)
+{
+	return ath5k_hw_reg_read(ah, AR5K_INTPEND) == 1 ? 1 : 0;
+}
+
+/**
+ * ath5k_hw_get_isr() - Get interrupt status
+ * @ah: The @struct ath5k_hw
+ * @interrupt_mask: Driver's interrupt mask used to filter out
+ * interrupts in sw.
+ *
+ * This function is used inside our interrupt handler to determine the reason
+ * for the interrupt by reading Primary Interrupt Status Register. Returns an
+ * abstract interrupt status mask which is mostly ISR with some uncommon bits
+ * being mapped on some standard non hw-specific positions
+ * (check out &ath5k_int).
+ *
+ * NOTE: We do write-to-clear, so the active PISR/SISR bits at the time this
+ * function gets called are cleared on return.
+ */
+int
+ath5k_hw_get_isr(struct ath5k_hw *ah, enum ath5k_int *interrupt_mask)
+{
+	u32 data = 0;
+
+	/*
+	 * Read interrupt status from Primary Interrupt
+	 * Register.
+	 *
+	 * Note: PISR/SISR Not available on 5210
+	 */
+	if (ah->ah_version == AR5K_AR5210) {
+		u32 isr = 0;
+		isr = ath5k_hw_reg_read(ah, AR5K_ISR);
+		if (unlikely(isr == AR5K_INT_NOCARD)) {
+			*interrupt_mask = isr;
+			return -ENODEV;
+		}
+
+		/*
+		 * Filter out the non-common bits from the interrupt
+		 * status.
+		 */
+		*interrupt_mask = (isr & AR5K_INT_COMMON) & ah->ah_imr;
+
+		/* Hanlde INT_FATAL */
+		if (unlikely(isr & (AR5K_ISR_SSERR | AR5K_ISR_MCABT
+						| AR5K_ISR_DPERR)))
+			*interrupt_mask |= AR5K_INT_FATAL;
+
+		/*
+		 * XXX: BMISS interrupts may occur after association.
+		 * I found this on 5210 code but it needs testing. If this is
+		 * true we should disable them before assoc and re-enable them
+		 * after a successful assoc + some jiffies.
+			interrupt_mask &= ~AR5K_INT_BMISS;
+		 */
+
+		data = isr;
+	} else {
+		u32 pisr = 0;
+		u32 pisr_clear = 0;
+		u32 sisr0 = 0;
+		u32 sisr1 = 0;
+		u32 sisr2 = 0;
+		u32 sisr3 = 0;
+		u32 sisr4 = 0;
+
+		/* Read PISR and SISRs... */
+		pisr = ath5k_hw_reg_read(ah, AR5K_PISR);
+		if (unlikely(pisr == AR5K_INT_NOCARD)) {
+			*interrupt_mask = pisr;
+			return -ENODEV;
+		}
+
+		sisr0 = ath5k_hw_reg_read(ah, AR5K_SISR0);
+		sisr1 = ath5k_hw_reg_read(ah, AR5K_SISR1);
+		sisr2 = ath5k_hw_reg_read(ah, AR5K_SISR2);
+		sisr3 = ath5k_hw_reg_read(ah, AR5K_SISR3);
+		sisr4 = ath5k_hw_reg_read(ah, AR5K_SISR4);
+
+		/*
+		 * PISR holds the logical OR of interrupt bits
+		 * from SISR registers:
+		 *
+		 * TXOK and TXDESC  -> Logical OR of TXOK and TXDESC
+		 *			per-queue bits on SISR0
+		 *
+		 * TXERR and TXEOL -> Logical OR of TXERR and TXEOL
+		 *			per-queue bits on SISR1
+		 *
+		 * TXURN -> Logical OR of TXURN per-queue bits on SISR2
+		 *
+		 * HIUERR -> Logical OR of MCABT, SSERR and DPER bits on SISR2
+		 *
+		 * BCNMISC -> Logical OR of TIM, CAB_END, DTIM_SYNC
+		 *		BCN_TIMEOUT, CAB_TIMEOUT and DTIM
+		 *		(and TSFOOR ?) bits on SISR2
+		 *
+		 * QCBRORN and QCBRURN -> Logical OR of QCBRORN and
+		 *			QCBRURN per-queue bits on SISR3
+		 * QTRIG -> Logical OR of QTRIG per-queue bits on SISR4
+		 *
+		 * If we clean these bits on PISR we 'll also clear all
+		 * related bits from SISRs, e.g. if we write the TXOK bit on
+		 * PISR we 'll clean all TXOK bits from SISR0 so if a new TXOK
+		 * interrupt got fired for another queue while we were reading
+		 * the interrupt registers and we write back the TXOK bit on
+		 * PISR we 'll lose it. So make sure that we don't write back
+		 * on PISR any bits that come from SISRs. Clearing them from
+		 * SISRs will also clear PISR so no need to worry here.
+		 */
+
+		/* XXX: There seems to be  an issue on some cards
+		 *	with tx interrupt flags not being updated
+		 *	on PISR despite that all Tx interrupt bits
+		 * 	are cleared on SISRs. Since we handle all
+		 *	Tx queues all together it shouldn't be an
+		 *	issue if we clear Tx interrupt flags also
+		 * 	on PISR to avoid that.
+		 */
+		pisr_clear = (pisr & ~AR5K_ISR_BITS_FROM_SISRS) |
+					(pisr & AR5K_INT_TX_ALL);
+
+		/*
+		 * Write to clear them...
+		 * Note: This means that each bit we write back
+		 * to the registers will get cleared, leaving the
+		 * rest unaffected. So this won't affect new interrupts
+		 * we didn't catch while reading/processing, we 'll get
+		 * them next time get_isr gets called.
+		 */
+		ath5k_hw_reg_write(ah, sisr0, AR5K_SISR0);
+		ath5k_hw_reg_write(ah, sisr1, AR5K_SISR1);
+		ath5k_hw_reg_write(ah, sisr2, AR5K_SISR2);
+		ath5k_hw_reg_write(ah, sisr3, AR5K_SISR3);
+		ath5k_hw_reg_write(ah, sisr4, AR5K_SISR4);
+		ath5k_hw_reg_write(ah, pisr_clear, AR5K_PISR);
+		/* Flush previous write */
+		ath5k_hw_reg_read(ah, AR5K_PISR);
+
+		/*
+		 * Filter out the non-common bits from the interrupt
+		 * status.
+		 */
+		*interrupt_mask = (pisr & AR5K_INT_COMMON) & ah->ah_imr;
+
+		ah->ah_txq_isr_txok_all = 0;
+
+		/* We treat TXOK,TXDESC, TXERR and TXEOL
+		 * the same way (schedule the tx tasklet)
+		 * so we track them all together per queue */
+		if (pisr & AR5K_ISR_TXOK)
+			ah->ah_txq_isr_txok_all |= AR5K_REG_MS(sisr0,
+						AR5K_SISR0_QCU_TXOK);
+
+		if (pisr & AR5K_ISR_TXDESC)
+			ah->ah_txq_isr_txok_all |= AR5K_REG_MS(sisr0,
+						AR5K_SISR0_QCU_TXDESC);
+
+		if (pisr & AR5K_ISR_TXERR)
+			ah->ah_txq_isr_txok_all |= AR5K_REG_MS(sisr1,
+						AR5K_SISR1_QCU_TXERR);
+
+		if (pisr & AR5K_ISR_TXEOL)
+			ah->ah_txq_isr_txok_all |= AR5K_REG_MS(sisr1,
+						AR5K_SISR1_QCU_TXEOL);
+
+		/* Misc Beacon related interrupts */
+
+		/* For AR5211 */
+		if (pisr & AR5K_ISR_TIM)
+			*interrupt_mask |= AR5K_INT_TIM;
+
+		/* For AR5212+ */
+		if (pisr & AR5K_ISR_BCNMISC) {
+			if (sisr2 & AR5K_SISR2_TIM)
+				*interrupt_mask |= AR5K_INT_TIM;
+			if (sisr2 & AR5K_SISR2_DTIM)
+				*interrupt_mask |= AR5K_INT_DTIM;
+			if (sisr2 & AR5K_SISR2_DTIM_SYNC)
+				*interrupt_mask |= AR5K_INT_DTIM_SYNC;
+			if (sisr2 & AR5K_SISR2_BCN_TIMEOUT)
+				*interrupt_mask |= AR5K_INT_BCN_TIMEOUT;
+			if (sisr2 & AR5K_SISR2_CAB_TIMEOUT)
+				*interrupt_mask |= AR5K_INT_CAB_TIMEOUT;
+		}
+
+		/* Below interrupts are unlikely to happen */
+
+		/* HIU = Host Interface Unit (PCI etc)
+		 * Can be one of MCABT, SSERR, DPERR from SISR2 */
+		if (unlikely(pisr & (AR5K_ISR_HIUERR)))
+			*interrupt_mask |= AR5K_INT_FATAL;
+
+		/*Beacon Not Ready*/
+		if (unlikely(pisr & (AR5K_ISR_BNR)))
+			*interrupt_mask |= AR5K_INT_BNR;
+
+		/* A queue got CBR overrun */
+		if (unlikely(pisr & (AR5K_ISR_QCBRORN)))
+			*interrupt_mask |= AR5K_INT_QCBRORN;
+
+		/* A queue got CBR underrun */
+		if (unlikely(pisr & (AR5K_ISR_QCBRURN)))
+			*interrupt_mask |= AR5K_INT_QCBRURN;
+
+		/* A queue got triggered */
+		if (unlikely(pisr & (AR5K_ISR_QTRIG)))
+			*interrupt_mask |= AR5K_INT_QTRIG;
+
+		data = pisr;
+	}
+
+	/*
+	 * In case we didn't handle anything,
+	 * print the register value.
+	 */
+	if (unlikely(*interrupt_mask == 0 && net_ratelimit()))
+		ATH5K_PRINTF("ISR: 0x%08x IMR: 0x%08x\n", data, ah->ah_imr);
+
+	return 0;
+}
+
+/**
+ * ath5k_hw_set_imr() - Set interrupt mask
+ * @ah: The &struct ath5k_hw
+ * @new_mask: The new interrupt mask to be set
+ *
+ * Set the interrupt mask in hw to save interrupts. We do that by mapping
+ * ath5k_int bits to hw-specific bits to remove abstraction and writing
+ * Interrupt Mask Register.
+ */
+enum ath5k_int
+ath5k_hw_set_imr(struct ath5k_hw *ah, enum ath5k_int new_mask)
+{
+	enum ath5k_int old_mask, int_mask;
+
+	old_mask = ah->ah_imr;
+
+	/*
+	 * Disable card interrupts to prevent any race conditions
+	 * (they will be re-enabled afterwards if AR5K_INT GLOBAL
+	 * is set again on the new mask).
+	 */
+	if (old_mask & AR5K_INT_GLOBAL) {
+		ath5k_hw_reg_write(ah, AR5K_IER_DISABLE, AR5K_IER);
+		ath5k_hw_reg_read(ah, AR5K_IER);
+	}
+
+	/*
+	 * Add additional, chipset-dependent interrupt mask flags
+	 * and write them to the IMR (interrupt mask register).
+	 */
+	int_mask = new_mask & AR5K_INT_COMMON;
+
+	if (ah->ah_version != AR5K_AR5210) {
+		/* Preserve per queue TXURN interrupt mask */
+		u32 simr2 = ath5k_hw_reg_read(ah, AR5K_SIMR2)
+				& AR5K_SIMR2_QCU_TXURN;
+
+		/* Fatal interrupt abstraction for 5211+ */
+		if (new_mask & AR5K_INT_FATAL) {
+			int_mask |= AR5K_IMR_HIUERR;
+			simr2 |= (AR5K_SIMR2_MCABT | AR5K_SIMR2_SSERR
+				| AR5K_SIMR2_DPERR);
+		}
+
+		/* Misc beacon related interrupts */
+		if (new_mask & AR5K_INT_TIM)
+			int_mask |= AR5K_IMR_TIM;
+
+		if (new_mask & AR5K_INT_TIM)
+			simr2 |= AR5K_SISR2_TIM;
+		if (new_mask & AR5K_INT_DTIM)
+			simr2 |= AR5K_SISR2_DTIM;
+		if (new_mask & AR5K_INT_DTIM_SYNC)
+			simr2 |= AR5K_SISR2_DTIM_SYNC;
+		if (new_mask & AR5K_INT_BCN_TIMEOUT)
+			simr2 |= AR5K_SISR2_BCN_TIMEOUT;
+		if (new_mask & AR5K_INT_CAB_TIMEOUT)
+			simr2 |= AR5K_SISR2_CAB_TIMEOUT;
+
+		/*Beacon Not Ready*/
+		if (new_mask & AR5K_INT_BNR)
+			int_mask |= AR5K_INT_BNR;
+
+		/* Note: Per queue interrupt masks
+		 * are set via ath5k_hw_reset_tx_queue() (qcu.c) */
+		ath5k_hw_reg_write(ah, int_mask, AR5K_PIMR);
+		ath5k_hw_reg_write(ah, simr2, AR5K_SIMR2);
+
+	} else {
+		/* Fatal interrupt abstraction for 5210 */
+		if (new_mask & AR5K_INT_FATAL)
+			int_mask |= (AR5K_IMR_SSERR | AR5K_IMR_MCABT
+				| AR5K_IMR_HIUERR | AR5K_IMR_DPERR);
+
+		/* Only common interrupts left for 5210 (no SIMRs) */
+		ath5k_hw_reg_write(ah, int_mask, AR5K_IMR);
+	}
+
+	/* If RXNOFRM interrupt is masked disable it
+	 * by setting AR5K_RXNOFRM to zero */
+	if (!(new_mask & AR5K_INT_RXNOFRM))
+		ath5k_hw_reg_write(ah, 0, AR5K_RXNOFRM);
+
+	/* Store new interrupt mask */
+	ah->ah_imr = new_mask;
+
+	/* ..re-enable interrupts if AR5K_INT_GLOBAL is set */
+	if (new_mask & AR5K_INT_GLOBAL) {
+		ath5k_hw_reg_write(ah, AR5K_IER_ENABLE, AR5K_IER);
+		ath5k_hw_reg_read(ah, AR5K_IER);
+	}
+
+	return old_mask;
+}
+
+
+/********************\
+ Init/Stop functions
+\********************/
+
+/**
+ * ath5k_hw_dma_init() - Initialize DMA unit
+ * @ah: The &struct ath5k_hw
+ *
+ * Set DMA size and pre-enable interrupts
+ * (driver handles tx/rx buffer setup and
+ * dma start/stop)
+ *
+ * XXX: Save/restore RXDP/TXDP registers ?
+ */
+void
+ath5k_hw_dma_init(struct ath5k_hw *ah)
+{
+	/*
+	 * Set Rx/Tx DMA Configuration
+	 *
+	 * Set standard DMA size (128). Note that
+	 * a DMA size of 512 causes rx overruns and tx errors
+	 * on pci-e cards (tested on 5424 but since rx overruns
+	 * also occur on 5416/5418 with madwifi we set 128
+	 * for all PCI-E cards to be safe).
+	 *
+	 * XXX: need to check 5210 for this
+	 * TODO: Check out tx trigger level, it's always 64 on dumps but I
+	 * guess we can tweak it and see how it goes ;-)
+	 */
+	if (ah->ah_version != AR5K_AR5210) {
+		AR5K_REG_WRITE_BITS(ah, AR5K_TXCFG,
+			AR5K_TXCFG_SDMAMR, AR5K_DMASIZE_128B);
+		AR5K_REG_WRITE_BITS(ah, AR5K_RXCFG,
+			AR5K_RXCFG_SDMAMW, AR5K_DMASIZE_128B);
+	}
+
+	/* Pre-enable interrupts on 5211/5212*/
+	if (ah->ah_version != AR5K_AR5210)
+		ath5k_hw_set_imr(ah, ah->ah_imr);
+
+}
+
+/**
+ * ath5k_hw_dma_stop() - stop DMA unit
+ * @ah: The &struct ath5k_hw
+ *
+ * Stop tx/rx DMA and interrupts. Returns
+ * -EBUSY if tx or rx dma failed to stop.
+ *
+ * XXX: Sometimes DMA unit hangs and we have
+ * stuck frames on tx queues, only a reset
+ * can fix that.
+ */
+int
+ath5k_hw_dma_stop(struct ath5k_hw *ah)
+{
+	int i, qmax, err;
+	err = 0;
+
+	/* Disable interrupts */
+	ath5k_hw_set_imr(ah, 0);
+
+	/* Stop rx dma */
+	err = ath5k_hw_stop_rx_dma(ah);
+	if (err)
+		return err;
+
+	/* Clear any pending interrupts
+	 * and disable tx dma */
+	if (ah->ah_version != AR5K_AR5210) {
+		ath5k_hw_reg_write(ah, 0xffffffff, AR5K_PISR);
+		qmax = AR5K_NUM_TX_QUEUES;
+	} else {
+		/* PISR/SISR Not available on 5210 */
+		ath5k_hw_reg_read(ah, AR5K_ISR);
+		qmax = AR5K_NUM_TX_QUEUES_NOQCU;
+	}
+
+	for (i = 0; i < qmax; i++) {
+		err = ath5k_hw_stop_tx_dma(ah, i);
+		/* -EINVAL -> queue inactive */
+		if (err && err != -EINVAL)
+			return err;
+	}
+
+	return 0;
+}

linux-7.2.3/drivers/net/wireless/ath/ath5k/eeprom.h

@@ -0,0 +1,492 @@
+/*
+ * Copyright (c) 2004-2008 Reyk Floeter <reyk@openbsd.org>
+ * Copyright (c) 2006-2008 Nick Kossifidis <mickflemm@gmail.com>
+ *
+ * Permission to use, copy, modify, and distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+/*
+ * Common ar5xxx EEPROM data offsets (set these on AR5K_EEPROM_BASE)
+ */
+#define	AR5K_EEPROM_PCIE_OFFSET		0x02	/* Contains offset to PCI-E infos */
+#define	AR5K_EEPROM_PCIE_SERDES_SECTION	0x40	/* PCIE_OFFSET points here when
+						 * SERDES infos are present */
+#define AR5K_EEPROM_MAGIC		0x003d	/* EEPROM Magic number */
+#define AR5K_EEPROM_MAGIC_VALUE		0x5aa5	/* Default - found on EEPROM */
+
+#define	AR5K_EEPROM_IS_HB63		0x000b	/* Talon detect */
+
+#define AR5K_EEPROM_RFKILL		0x0f
+#define AR5K_EEPROM_RFKILL_GPIO_SEL	0x0000001c
+#define AR5K_EEPROM_RFKILL_GPIO_SEL_S	2
+#define AR5K_EEPROM_RFKILL_POLARITY	0x00000002
+#define AR5K_EEPROM_RFKILL_POLARITY_S	1
+
+#define AR5K_EEPROM_REG_DOMAIN		0x00bf	/* EEPROM regdom */
+
+/* FLASH(EEPROM) Defines for AR531X chips */
+#define AR5K_EEPROM_SIZE_LOWER		0x1b /* size info -- lower */
+#define AR5K_EEPROM_SIZE_UPPER		0x1c /* size info -- upper */
+#define AR5K_EEPROM_SIZE_UPPER_MASK	0xfff0
+#define AR5K_EEPROM_SIZE_UPPER_SHIFT	4
+#define AR5K_EEPROM_SIZE_ENDLOC_SHIFT	12
+
+#define AR5K_EEPROM_CHECKSUM		0x00c0	/* EEPROM checksum */
+#define AR5K_EEPROM_INFO_BASE		0x00c0	/* EEPROM header */
+#define AR5K_EEPROM_INFO_MAX		(0x400 - AR5K_EEPROM_INFO_BASE)
+#define AR5K_EEPROM_INFO_CKSUM		0xffff
+#define AR5K_EEPROM_INFO(_n)		(AR5K_EEPROM_INFO_BASE + (_n))
+
+#define AR5K_EEPROM_VERSION		AR5K_EEPROM_INFO(1)	/* EEPROM Version */
+#define AR5K_EEPROM_VERSION_3_0		0x3000	/* No idea what's going on before this version */
+#define AR5K_EEPROM_VERSION_3_1		0x3001	/* ob/db values for 2GHz (ar5211_rfregs) */
+#define AR5K_EEPROM_VERSION_3_2		0x3002	/* different frequency representation (eeprom_bin2freq) */
+#define AR5K_EEPROM_VERSION_3_3		0x3003	/* offsets changed, has 32 CTLs (see below) and ee_false_detect (eeprom_read_modes) */
+#define AR5K_EEPROM_VERSION_3_4		0x3004	/* has ee_i_gain, ee_cck_ofdm_power_delta (eeprom_read_modes) */
+#define AR5K_EEPROM_VERSION_4_0		0x4000	/* has ee_misc, ee_cal_pier, ee_turbo_max_power and ee_xr_power (eeprom_init) */
+#define AR5K_EEPROM_VERSION_4_1		0x4001	/* has ee_margin_tx_rx (eeprom_init) */
+#define AR5K_EEPROM_VERSION_4_2		0x4002	/* has ee_cck_ofdm_gain_delta (eeprom_init) */
+#define AR5K_EEPROM_VERSION_4_3		0x4003	/* power calibration changes */
+#define AR5K_EEPROM_VERSION_4_4		0x4004
+#define AR5K_EEPROM_VERSION_4_5		0x4005
+#define AR5K_EEPROM_VERSION_4_6		0x4006	/* has ee_scaled_cck_delta */
+#define AR5K_EEPROM_VERSION_4_7		0x3007	/* 4007 ? */
+#define AR5K_EEPROM_VERSION_4_9		0x4009	/* EAR futureproofing */
+#define AR5K_EEPROM_VERSION_5_0		0x5000	/* Has 2413 PDADC calibration etc */
+#define AR5K_EEPROM_VERSION_5_1		0x5001	/* Has capability values */
+#define AR5K_EEPROM_VERSION_5_3		0x5003	/* Has spur mitigation tables */
+
+#define AR5K_EEPROM_MODE_11A		0
+#define AR5K_EEPROM_MODE_11B		1
+#define AR5K_EEPROM_MODE_11G		2
+
+#define AR5K_EEPROM_HDR			AR5K_EEPROM_INFO(2)	/* Header that contains the device caps */
+#define AR5K_EEPROM_HDR_11A(_v)		(((_v) >> AR5K_EEPROM_MODE_11A) & 0x1)
+#define AR5K_EEPROM_HDR_11B(_v)		(((_v) >> AR5K_EEPROM_MODE_11B) & 0x1)
+#define AR5K_EEPROM_HDR_11G(_v)		(((_v) >> AR5K_EEPROM_MODE_11G) & 0x1)
+#define AR5K_EEPROM_HDR_T_2GHZ_DIS(_v)	(((_v) >> 3) & 0x1)	/* Disable turbo for 2GHz */
+#define AR5K_EEPROM_HDR_T_5GHZ_DBM(_v)	(((_v) >> 4) & 0x7f)	/* Max turbo power for < 2W power consumption */
+#define AR5K_EEPROM_HDR_DEVICE(_v)	(((_v) >> 11) & 0x7)	/* Device type (1 Cardbus, 2 PCI, 3 MiniPCI, 4 AP) */
+#define AR5K_EEPROM_HDR_RFKILL(_v)	(((_v) >> 14) & 0x1)	/* Device has RFKill support */
+#define AR5K_EEPROM_HDR_T_5GHZ_DIS(_v)	(((_v) >> 15) & 0x1)	/* Disable turbo for 5GHz */
+
+/* Newer EEPROMs are using a different offset */
+#define AR5K_EEPROM_OFF(_v, _v3_0, _v3_3) \
+	(((_v) >= AR5K_EEPROM_VERSION_3_3) ? _v3_3 : _v3_0)
+
+#define AR5K_EEPROM_ANT_GAIN(_v)	AR5K_EEPROM_OFF(_v, 0x00c4, 0x00c3)
+#define AR5K_EEPROM_ANT_GAIN_5GHZ(_v)	((s8)(((_v) >> 8) & 0xff))
+#define AR5K_EEPROM_ANT_GAIN_2GHZ(_v)	((s8)((_v) & 0xff))
+
+/* Misc values available since EEPROM 4.0 */
+#define AR5K_EEPROM_MISC0		AR5K_EEPROM_INFO(4)
+#define AR5K_EEPROM_EARSTART(_v)	((_v) & 0xfff)
+#define AR5K_EEPROM_HDR_XR2_DIS(_v)	(((_v) >> 12) & 0x1)
+#define AR5K_EEPROM_HDR_XR5_DIS(_v)	(((_v) >> 13) & 0x1)
+#define AR5K_EEPROM_EEMAP(_v)		(((_v) >> 14) & 0x3)
+
+#define AR5K_EEPROM_MISC1			AR5K_EEPROM_INFO(5)
+#define AR5K_EEPROM_TARGET_PWRSTART(_v)		((_v) & 0xfff)
+#define AR5K_EEPROM_HAS32KHZCRYSTAL(_v)		(((_v) >> 14) & 0x1)	/* has 32KHz crystal for sleep mode */
+#define AR5K_EEPROM_HAS32KHZCRYSTAL_OLD(_v)	(((_v) >> 15) & 0x1)
+
+#define AR5K_EEPROM_MISC2			AR5K_EEPROM_INFO(6)
+#define AR5K_EEPROM_EEP_FILE_VERSION(_v)	(((_v) >> 8) & 0xff)
+#define AR5K_EEPROM_EAR_FILE_VERSION(_v)	((_v) & 0xff)
+
+#define AR5K_EEPROM_MISC3		AR5K_EEPROM_INFO(7)
+#define AR5K_EEPROM_ART_BUILD_NUM(_v)	(((_v) >> 10) & 0x3f)
+#define AR5K_EEPROM_EAR_FILE_ID(_v)	((_v) & 0xff)
+
+#define AR5K_EEPROM_MISC4		AR5K_EEPROM_INFO(8)
+#define AR5K_EEPROM_CAL_DATA_START(_v)	(((_v) >> 4) & 0xfff)
+#define AR5K_EEPROM_MASK_R0(_v)		(((_v) >> 2) & 0x3)	/* modes supported by radio 0 (bit 1: G, bit 2: A) */
+#define AR5K_EEPROM_MASK_R1(_v)		((_v) & 0x3)		/* modes supported by radio 1 (bit 1: G, bit 2: A) */
+
+#define AR5K_EEPROM_MISC5		AR5K_EEPROM_INFO(9)
+#define AR5K_EEPROM_COMP_DIS(_v)	((_v) & 0x1)		/* disable compression */
+#define AR5K_EEPROM_AES_DIS(_v)		(((_v) >> 1) & 0x1)	/* disable AES */
+#define AR5K_EEPROM_FF_DIS(_v)		(((_v) >> 2) & 0x1)	/* disable fast frames */
+#define AR5K_EEPROM_BURST_DIS(_v)	(((_v) >> 3) & 0x1)	/* disable bursting */
+#define AR5K_EEPROM_MAX_QCU(_v)		(((_v) >> 4) & 0xf)	/* max number of QCUs. defaults to 10 */
+#define AR5K_EEPROM_HEAVY_CLIP_EN(_v)	(((_v) >> 8) & 0x1)	/* enable heavy clipping */
+#define AR5K_EEPROM_KEY_CACHE_SIZE(_v)	(((_v) >> 12) & 0xf)	/* key cache size. defaults to 128 */
+
+#define AR5K_EEPROM_MISC6		AR5K_EEPROM_INFO(10)
+#define AR5K_EEPROM_TX_CHAIN_DIS	((_v) & 0x7)		/* MIMO chains disabled for TX bitmask */
+#define AR5K_EEPROM_RX_CHAIN_DIS	(((_v) >> 3) & 0x7)	/* MIMO chains disabled for RX bitmask */
+#define AR5K_EEPROM_FCC_MID_EN		(((_v) >> 6) & 0x1)	/* 5.47-5.7GHz supported */
+#define AR5K_EEPROM_JAP_U1EVEN_EN	(((_v) >> 7) & 0x1)	/* Japan UNII1 band (5.15-5.25GHz) on even channels (5180, 5200, 5220, 5240) supported */
+#define AR5K_EEPROM_JAP_U2_EN		(((_v) >> 8) & 0x1)	/* Japan UNII2 band (5.25-5.35GHz) supported */
+#define AR5K_EEPROM_JAP_MID_EN		(((_v) >> 9) & 0x1)	/* Japan band from 5.47-5.7GHz supported */
+#define AR5K_EEPROM_JAP_U1ODD_EN	(((_v) >> 10) & 0x1)	/* Japan UNII2 band (5.15-5.25GHz) on odd channels (5170, 5190, 5210, 5230) supported */
+#define AR5K_EEPROM_JAP_11A_NEW_EN	(((_v) >> 11) & 0x1)	/* Japan A mode enabled (using even channels) */
+
+/* calibration settings */
+#define AR5K_EEPROM_MODES_11A(_v)	AR5K_EEPROM_OFF(_v, 0x00c5, 0x00d4)
+#define AR5K_EEPROM_MODES_11B(_v)	AR5K_EEPROM_OFF(_v, 0x00d0, 0x00f2)
+#define AR5K_EEPROM_MODES_11G(_v)	AR5K_EEPROM_OFF(_v, 0x00da, 0x010d)
+#define AR5K_EEPROM_CTL(_v)		AR5K_EEPROM_OFF(_v, 0x00e4, 0x0128)	/* Conformance test limits */
+#define AR5K_EEPROM_GROUPS_START(_v)	AR5K_EEPROM_OFF(_v, 0x0100, 0x0150)	/* Start of Groups */
+#define AR5K_EEPROM_GROUP1_OFFSET	0x0
+#define AR5K_EEPROM_GROUP2_OFFSET	0x5
+#define AR5K_EEPROM_GROUP3_OFFSET	0x37
+#define AR5K_EEPROM_GROUP4_OFFSET	0x46
+#define AR5K_EEPROM_GROUP5_OFFSET	0x55
+#define AR5K_EEPROM_GROUP6_OFFSET	0x65
+#define AR5K_EEPROM_GROUP7_OFFSET	0x69
+#define AR5K_EEPROM_GROUP8_OFFSET	0x6f
+
+#define AR5K_EEPROM_TARGET_PWR_OFF_11A(_v)	AR5K_EEPROM_OFF(_v, AR5K_EEPROM_GROUPS_START(_v) + \
+								AR5K_EEPROM_GROUP5_OFFSET, 0x0000)
+#define AR5K_EEPROM_TARGET_PWR_OFF_11B(_v)	AR5K_EEPROM_OFF(_v, AR5K_EEPROM_GROUPS_START(_v) + \
+								AR5K_EEPROM_GROUP6_OFFSET, 0x0010)
+#define AR5K_EEPROM_TARGET_PWR_OFF_11G(_v)	AR5K_EEPROM_OFF(_v, AR5K_EEPROM_GROUPS_START(_v) + \
+								AR5K_EEPROM_GROUP7_OFFSET, 0x0014)
+
+/* [3.1 - 3.3] */
+#define AR5K_EEPROM_OBDB0_2GHZ		0x00ec
+#define AR5K_EEPROM_OBDB1_2GHZ		0x00ed
+
+#define AR5K_EEPROM_PROTECT		0x003f	/* EEPROM protect status */
+#define AR5K_EEPROM_PROTECT_RD_0_31	0x0001	/* Read protection bit for offsets 0x0 - 0x1f */
+#define AR5K_EEPROM_PROTECT_WR_0_31	0x0002	/* Write protection bit for offsets 0x0 - 0x1f */
+#define AR5K_EEPROM_PROTECT_RD_32_63	0x0004	/* 0x20 - 0x3f */
+#define AR5K_EEPROM_PROTECT_WR_32_63	0x0008
+#define AR5K_EEPROM_PROTECT_RD_64_127	0x0010	/* 0x40 - 0x7f */
+#define AR5K_EEPROM_PROTECT_WR_64_127	0x0020
+#define AR5K_EEPROM_PROTECT_RD_128_191	0x0040	/* 0x80 - 0xbf (regdom) */
+#define AR5K_EEPROM_PROTECT_WR_128_191	0x0080
+#define AR5K_EEPROM_PROTECT_RD_192_207	0x0100	/* 0xc0 - 0xcf */
+#define AR5K_EEPROM_PROTECT_WR_192_207	0x0200
+#define AR5K_EEPROM_PROTECT_RD_208_223	0x0400	/* 0xd0 - 0xdf */
+#define AR5K_EEPROM_PROTECT_WR_208_223	0x0800
+#define AR5K_EEPROM_PROTECT_RD_224_239	0x1000	/* 0xe0 - 0xef */
+#define AR5K_EEPROM_PROTECT_WR_224_239	0x2000
+#define AR5K_EEPROM_PROTECT_RD_240_255	0x4000	/* 0xf0 - 0xff */
+#define AR5K_EEPROM_PROTECT_WR_240_255	0x8000
+
+/* Some EEPROM defines */
+#define AR5K_EEPROM_EEP_SCALE		100
+#define AR5K_EEPROM_EEP_DELTA		10
+#define AR5K_EEPROM_N_MODES		3
+#define AR5K_EEPROM_N_5GHZ_CHAN		10
+#define AR5K_EEPROM_N_5GHZ_RATE_CHAN	8
+#define AR5K_EEPROM_N_2GHZ_CHAN		3
+#define AR5K_EEPROM_N_2GHZ_CHAN_2413	4
+#define	AR5K_EEPROM_N_2GHZ_CHAN_MAX	4
+#define AR5K_EEPROM_MAX_CHAN		10
+#define AR5K_EEPROM_N_PWR_POINTS_5111	11
+#define AR5K_EEPROM_N_PCDAC		11
+#define AR5K_EEPROM_N_PHASE_CAL		5
+#define AR5K_EEPROM_N_TEST_FREQ		8
+#define AR5K_EEPROM_N_EDGES		8
+#define AR5K_EEPROM_N_INTERCEPTS	11
+#define AR5K_EEPROM_FREQ_M(_v)		AR5K_EEPROM_OFF(_v, 0x7f, 0xff)
+#define AR5K_EEPROM_PCDAC_M		0x3f
+#define AR5K_EEPROM_PCDAC_START		1
+#define AR5K_EEPROM_PCDAC_STOP		63
+#define AR5K_EEPROM_PCDAC_STEP		1
+#define AR5K_EEPROM_NON_EDGE_M		0x40
+#define AR5K_EEPROM_CHANNEL_POWER	8
+#define AR5K_EEPROM_N_OBDB		4
+#define AR5K_EEPROM_OBDB_DIS		0xffff
+#define AR5K_EEPROM_CHANNEL_DIS		0xff
+#define AR5K_EEPROM_SCALE_OC_DELTA(_x)	(((_x) * 2) / 10)
+#define AR5K_EEPROM_N_CTLS(_v)		AR5K_EEPROM_OFF(_v, 16, 32)
+#define AR5K_EEPROM_MAX_CTLS		32
+#define AR5K_EEPROM_N_PD_CURVES		4
+#define AR5K_EEPROM_N_XPD0_POINTS	4
+#define AR5K_EEPROM_N_XPD3_POINTS	3
+#define AR5K_EEPROM_N_PD_GAINS		4
+#define AR5K_EEPROM_N_PD_POINTS		5
+#define AR5K_EEPROM_N_INTERCEPT_10_2GHZ	35
+#define AR5K_EEPROM_N_INTERCEPT_10_5GHZ	55
+#define AR5K_EEPROM_POWER_M		0x3f
+#define AR5K_EEPROM_POWER_MIN		0
+#define AR5K_EEPROM_POWER_MAX		3150
+#define AR5K_EEPROM_POWER_STEP		50
+#define AR5K_EEPROM_POWER_TABLE_SIZE	64
+#define AR5K_EEPROM_N_POWER_LOC_11B	4
+#define AR5K_EEPROM_N_POWER_LOC_11G	6
+#define AR5K_EEPROM_I_GAIN		10
+#define AR5K_EEPROM_CCK_OFDM_DELTA	15
+#define AR5K_EEPROM_N_IQ_CAL		2
+/* 5GHz/2GHz */
+enum ath5k_eeprom_freq_bands {
+	AR5K_EEPROM_BAND_5GHZ = 0,
+	AR5K_EEPROM_BAND_2GHZ = 1,
+	AR5K_EEPROM_N_FREQ_BANDS,
+};
+/* Spur chans per freq band */
+#define	AR5K_EEPROM_N_SPUR_CHANS	5
+/* fbin value for chan 2464 x2 */
+#define	AR5K_EEPROM_5413_SPUR_CHAN_1	1640
+/* fbin value for chan 2420 x2 */
+#define	AR5K_EEPROM_5413_SPUR_CHAN_2	1200
+#define	AR5K_EEPROM_SPUR_CHAN_MASK	0x3FFF
+#define	AR5K_EEPROM_NO_SPUR		0x8000
+#define	AR5K_SPUR_CHAN_WIDTH			87
+#define	AR5K_SPUR_SYMBOL_WIDTH_BASE_100Hz	3125
+#define	AR5K_SPUR_SYMBOL_WIDTH_TURBO_100Hz	6250
+
+#define AR5K_EEPROM_READ(_o, _v) do {			\
+	if (!ath5k_hw_nvram_read(ah, (_o), &(_v)))	\
+		return -EIO;				\
+} while (0)
+
+#define AR5K_EEPROM_READ_HDR(_o, _v)					\
+	AR5K_EEPROM_READ(_o, ah->ah_capabilities.cap_eeprom._v);	\
+
+enum ath5k_ant_table {
+	AR5K_ANT_CTL		= 0,	/* Idle switch table settings */
+	AR5K_ANT_SWTABLE_A	= 1,	/* Switch table for antenna A */
+	AR5K_ANT_SWTABLE_B	= 2,	/* Switch table for antenna B */
+	AR5K_ANT_MAX,
+};
+
+enum ath5k_ctl_mode {
+	AR5K_CTL_11A = 0,
+	AR5K_CTL_11B = 1,
+	AR5K_CTL_11G = 2,
+	AR5K_CTL_TURBO = 3,
+	AR5K_CTL_TURBOG = 4,
+	AR5K_CTL_2GHT20 = 5,
+	AR5K_CTL_5GHT20 = 6,
+	AR5K_CTL_2GHT40 = 7,
+	AR5K_CTL_5GHT40 = 8,
+	AR5K_CTL_MODE_M = 15,
+};
+
+/* Per channel calibration data, used for power table setup */
+struct ath5k_chan_pcal_info_rf5111 {
+	/* Power levels in half dBm units
+	 * for one power curve. */
+	u8 pwr[AR5K_EEPROM_N_PWR_POINTS_5111];
+	/* PCDAC table steps
+	 * for the above values */
+	u8 pcdac[AR5K_EEPROM_N_PWR_POINTS_5111];
+	/* Starting PCDAC step */
+	u8 pcdac_min;
+	/* Final PCDAC step */
+	u8 pcdac_max;
+};
+
+struct ath5k_chan_pcal_info_rf5112 {
+	/* Power levels in quarter dBm units
+	 * for lower (0) and higher (3)
+	 * level curves in 0.25dB units */
+	s8 pwr_x0[AR5K_EEPROM_N_XPD0_POINTS];
+	s8 pwr_x3[AR5K_EEPROM_N_XPD3_POINTS];
+	/* PCDAC table steps
+	 * for the above values */
+	u8 pcdac_x0[AR5K_EEPROM_N_XPD0_POINTS];
+	u8 pcdac_x3[AR5K_EEPROM_N_XPD3_POINTS];
+};
+
+struct ath5k_chan_pcal_info_rf2413 {
+	/* Starting pwr/pddac values */
+	s8 pwr_i[AR5K_EEPROM_N_PD_GAINS];
+	u8 pddac_i[AR5K_EEPROM_N_PD_GAINS];
+	/* (pwr,pddac) points
+	 * power levels in 0.5dB units */
+	s8 pwr[AR5K_EEPROM_N_PD_GAINS]
+		[AR5K_EEPROM_N_PD_POINTS];
+	u8 pddac[AR5K_EEPROM_N_PD_GAINS]
+		[AR5K_EEPROM_N_PD_POINTS];
+};
+
+enum ath5k_powertable_type {
+	AR5K_PWRTABLE_PWR_TO_PCDAC = 0,
+	AR5K_PWRTABLE_LINEAR_PCDAC = 1,
+	AR5K_PWRTABLE_PWR_TO_PDADC = 2,
+};
+
+struct ath5k_pdgain_info {
+	u8 pd_points;
+	u8 *pd_step;
+	/* Power values are in
+	 * 0.25dB units */
+	s16 *pd_pwr;
+};
+
+struct ath5k_chan_pcal_info {
+	/* Frequency */
+	u16	freq;
+	/* Tx power boundaries */
+	s16	max_pwr;
+	s16	min_pwr;
+	union {
+		struct ath5k_chan_pcal_info_rf5111 rf5111_info;
+		struct ath5k_chan_pcal_info_rf5112 rf5112_info;
+		struct ath5k_chan_pcal_info_rf2413 rf2413_info;
+	};
+	/* Raw values used by phy code
+	 * Curves are stored in order from lower
+	 * gain to higher gain (max txpower -> min txpower) */
+	struct ath5k_pdgain_info *pd_curves;
+};
+
+/* Per rate calibration data for each mode,
+ * used for rate power table setup.
+ * Note: Values in 0.5dB units */
+struct ath5k_rate_pcal_info {
+	u16	freq; /* Frequency */
+	/* Power level for 6-24Mbit/s rates or
+	 * 1Mb rate */
+	u16	target_power_6to24;
+	/* Power level for 36Mbit rate or
+	 * 2Mb rate */
+	u16	target_power_36;
+	/* Power level for 48Mbit rate or
+	 * 5.5Mbit rate */
+	u16	target_power_48;
+	/* Power level for 54Mbit rate or
+	 * 11Mbit rate */
+	u16	target_power_54;
+};
+
+/* Power edges for conformance test limits */
+struct ath5k_edge_power {
+	u16 freq;
+	u16 edge; /* in half dBm */
+	bool flag;
+};
+
+/**
+ * struct ath5k_eeprom_info - EEPROM calibration data
+ *
+ * @ee_regdomain: ath/regd.c takes care of COUNTRY_ERD and WORLDWIDE_ROAMING
+ *	flags
+ * @ee_ant_gain: Antenna gain in 0.5dB steps signed [5211 only?]
+ * @ee_cck_ofdm_gain_delta: difference in gainF to output the same power for
+ *	OFDM and CCK packets
+ * @ee_cck_ofdm_power_delta: power difference between OFDM (6Mbps) and CCK
+ *	(11Mbps) rate in G mode. 0.1dB steps
+ * @ee_scaled_cck_delta: for Japan Channel 14: 0.1dB resolution
+ *
+ * @ee_i_cal: Initial I coefficient to correct I/Q mismatch in the receive path
+ * @ee_q_cal: Initial Q coefficient to correct I/Q mismatch in the receive path
+ * @ee_fixed_bias: use ee_ob and ee_db settings or use automatic control
+ * @ee_switch_settling: RX/TX Switch settling time
+ * @ee_atn_tx_rx: Difference in attenuation between TX and RX in 1dB steps
+ * @ee_ant_control: Antenna Control Settings
+ * @ee_ob: Bias current for Output stage of PA
+ *	B/G mode: Index [0] is used for AR2112/5112, otherwise [1]
+ *	A mode: [0] 5.15-5.25 [1] 5.25-5.50 [2] 5.50-5.70 [3] 5.70-5.85 GHz
+ * @ee_db: Bias current for Output stage of PA. see @ee_ob
+ * @ee_tx_end2xlna_enable: Time difference from when BB finishes sending a frame
+ *	to when the external LNA is activated
+ * @ee_tx_end2xpa_disable: Time difference from when BB finishes sending a frame
+ *	to when the external PA switch is deactivated
+ * @ee_tx_frm2xpa_enable: Time difference from when MAC sends frame to when
+ *	external PA switch is activated
+ * @ee_thr_62: Clear Channel Assessment (CCA) sensitivity
+ *	(IEEE802.11a section 17.3.10.5 )
+ * @ee_xlna_gain: Total gain of the LNA (information only)
+ * @ee_xpd: Use external (1) or internal power detector
+ * @ee_x_gain: Gain for external power detector output (differences in EEMAP
+ *	versions!)
+ * @ee_i_gain: Initial gain value after reset
+ * @ee_margin_tx_rx: Margin in dB when final attenuation stage should be used
+ *
+ * @ee_false_detect: Backoff in Sensitivity (dB) on channels with spur signals
+ * @ee_noise_floor_thr: Noise floor threshold in 1dB steps
+ * @ee_adc_desired_size: Desired amplitude for ADC, used by AGC; in 0.5 dB steps
+ * @ee_pga_desired_size: Desired output of PGA (for BB gain) in 0.5 dB steps
+ * @ee_pd_gain_overlap: PD ADC curves need to overlap in 0.5dB steps (ee_map>=2)
+ */
+struct ath5k_eeprom_info {
+
+	/* Header information */
+	u16	ee_magic;
+	u16	ee_protect;
+	u16	ee_regdomain;
+	u16	ee_version;
+	u16	ee_header;
+	u16	ee_ant_gain;
+	u8	ee_rfkill_pin;
+	bool	ee_rfkill_pol;
+	bool	ee_is_hb63;
+	bool	ee_serdes;
+	u16	ee_misc0;
+	u16	ee_misc1;
+	u16	ee_misc2;
+	u16	ee_misc3;
+	u16	ee_misc4;
+	u16	ee_misc5;
+	u16	ee_misc6;
+	u16	ee_cck_ofdm_gain_delta;
+	u16	ee_cck_ofdm_power_delta;
+	u16	ee_scaled_cck_delta;
+
+	/* RF Calibration settings (reset, rfregs) */
+	u16	ee_i_cal[AR5K_EEPROM_N_MODES];
+	u16	ee_q_cal[AR5K_EEPROM_N_MODES];
+	u16	ee_fixed_bias[AR5K_EEPROM_N_MODES];
+	u16	ee_turbo_max_power[AR5K_EEPROM_N_MODES];
+	u16	ee_xr_power[AR5K_EEPROM_N_MODES];
+	u16	ee_switch_settling[AR5K_EEPROM_N_MODES];
+	u16	ee_atn_tx_rx[AR5K_EEPROM_N_MODES];
+	u16	ee_ant_control[AR5K_EEPROM_N_MODES][AR5K_EEPROM_N_PCDAC];
+	u16	ee_ob[AR5K_EEPROM_N_MODES][AR5K_EEPROM_N_OBDB];
+	u16	ee_db[AR5K_EEPROM_N_MODES][AR5K_EEPROM_N_OBDB];
+	u16	ee_tx_end2xlna_enable[AR5K_EEPROM_N_MODES];
+	u16	ee_tx_end2xpa_disable[AR5K_EEPROM_N_MODES];
+	u16	ee_tx_frm2xpa_enable[AR5K_EEPROM_N_MODES];
+	u16	ee_thr_62[AR5K_EEPROM_N_MODES];
+	u16	ee_xlna_gain[AR5K_EEPROM_N_MODES];
+	u16	ee_xpd[AR5K_EEPROM_N_MODES];
+	u16	ee_x_gain[AR5K_EEPROM_N_MODES];
+	u16	ee_i_gain[AR5K_EEPROM_N_MODES];
+	u16	ee_margin_tx_rx[AR5K_EEPROM_N_MODES];
+	u16	ee_switch_settling_turbo[AR5K_EEPROM_N_MODES];
+	u16	ee_margin_tx_rx_turbo[AR5K_EEPROM_N_MODES];
+	u16	ee_atn_tx_rx_turbo[AR5K_EEPROM_N_MODES];
+
+	/* Power calibration data */
+	u16	ee_false_detect[AR5K_EEPROM_N_MODES];
+
+	/* Number of pd gain curves per mode */
+	u8	ee_pd_gains[AR5K_EEPROM_N_MODES];
+	/* Back mapping pdcurve number -> pdcurve index in pd->pd_curves */
+	u8	ee_pdc_to_idx[AR5K_EEPROM_N_MODES][AR5K_EEPROM_N_PD_GAINS];
+
+	u8	ee_n_piers[AR5K_EEPROM_N_MODES];
+	struct ath5k_chan_pcal_info	ee_pwr_cal_a[AR5K_EEPROM_N_5GHZ_CHAN];
+	struct ath5k_chan_pcal_info	ee_pwr_cal_b[AR5K_EEPROM_N_2GHZ_CHAN_MAX];
+	struct ath5k_chan_pcal_info	ee_pwr_cal_g[AR5K_EEPROM_N_2GHZ_CHAN_MAX];
+
+	/* Per rate target power levels */
+	u8	ee_rate_target_pwr_num[AR5K_EEPROM_N_MODES];
+	struct ath5k_rate_pcal_info	ee_rate_tpwr_a[AR5K_EEPROM_N_5GHZ_CHAN];
+	struct ath5k_rate_pcal_info	ee_rate_tpwr_b[AR5K_EEPROM_N_2GHZ_CHAN_MAX];
+	struct ath5k_rate_pcal_info	ee_rate_tpwr_g[AR5K_EEPROM_N_2GHZ_CHAN_MAX];
+
+	/* Conformance test limits (Unused) */
+	u8	ee_ctls;
+	u8	ee_ctl[AR5K_EEPROM_MAX_CTLS];
+	struct ath5k_edge_power ee_ctl_pwr[AR5K_EEPROM_N_EDGES * AR5K_EEPROM_MAX_CTLS];
+
+	/* Noise Floor Calibration settings */
+	s16	ee_noise_floor_thr[AR5K_EEPROM_N_MODES];
+	s8	ee_adc_desired_size[AR5K_EEPROM_N_MODES];
+	s8	ee_pga_desired_size[AR5K_EEPROM_N_MODES];
+	s8	ee_adc_desired_size_turbo[AR5K_EEPROM_N_MODES];
+	s8	ee_pga_desired_size_turbo[AR5K_EEPROM_N_MODES];
+	s8	ee_pd_gain_overlap;
+
+	/* Spur mitigation data (fbin values for spur channels) */
+	u16	ee_spur_chans[AR5K_EEPROM_N_SPUR_CHANS][AR5K_EEPROM_N_FREQ_BANDS];
+};

linux-7.2.3/drivers/net/wireless/ath/ath5k/gpio.c

@@ -0,0 +1,213 @@
+/*
+ * Copyright (c) 2004-2008 Reyk Floeter <reyk@openbsd.org>
+ * Copyright (c) 2006-2008 Nick Kossifidis <mickflemm@gmail.com>
+ *
+ * Permission to use, copy, modify, and distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+/****************\
+  GPIO Functions
+\****************/
+
+#include "ath5k.h"
+#include "reg.h"
+#include "debug.h"
+
+
+/**
+ * DOC: GPIO/LED functions
+ *
+ * Here we control the 6 bidirectional GPIO pins provided by the hw.
+ * We can set a GPIO pin to be an input or an output pin on GPIO control
+ * register and then read or set its status from GPIO data input/output
+ * registers.
+ *
+ * We also control the two LED pins provided by the hw, LED_0 is our
+ * "power" LED and LED_1 is our "network activity" LED but many scenarios
+ * are available from hw. Vendors might also provide LEDs connected to the
+ * GPIO pins, we handle them through the LED subsystem on led.c
+ */
+
+
+/**
+ * ath5k_hw_set_ledstate() - Set led state
+ * @ah: The &struct ath5k_hw
+ * @state: One of AR5K_LED_*
+ *
+ * Used to set the LED blinking state. This only
+ * works for the LED connected to the LED_0, LED_1 pins,
+ * not the GPIO based.
+ */
+void
+ath5k_hw_set_ledstate(struct ath5k_hw *ah, unsigned int state)
+{
+	u32 led;
+	/*5210 has different led mode handling*/
+	u32 led_5210;
+
+	/*Reset led status*/
+	if (ah->ah_version != AR5K_AR5210)
+		AR5K_REG_DISABLE_BITS(ah, AR5K_PCICFG,
+			AR5K_PCICFG_LEDMODE |  AR5K_PCICFG_LED);
+	else
+		AR5K_REG_DISABLE_BITS(ah, AR5K_PCICFG, AR5K_PCICFG_LED);
+
+	/*
+	 * Some blinking values, define at your wish
+	 */
+	switch (state) {
+	case AR5K_LED_SCAN:
+	case AR5K_LED_AUTH:
+		led = AR5K_PCICFG_LEDMODE_PROP | AR5K_PCICFG_LED_PEND;
+		led_5210 = AR5K_PCICFG_LED_PEND | AR5K_PCICFG_LED_BCTL;
+		break;
+
+	case AR5K_LED_INIT:
+		led = AR5K_PCICFG_LEDMODE_PROP | AR5K_PCICFG_LED_NONE;
+		led_5210 = AR5K_PCICFG_LED_PEND;
+		break;
+
+	case AR5K_LED_ASSOC:
+	case AR5K_LED_RUN:
+		led = AR5K_PCICFG_LEDMODE_PROP | AR5K_PCICFG_LED_ASSOC;
+		led_5210 = AR5K_PCICFG_LED_ASSOC;
+		break;
+
+	default:
+		led = AR5K_PCICFG_LEDMODE_PROM | AR5K_PCICFG_LED_NONE;
+		led_5210 = AR5K_PCICFG_LED_PEND;
+		break;
+	}
+
+	/*Write new status to the register*/
+	if (ah->ah_version != AR5K_AR5210)
+		AR5K_REG_ENABLE_BITS(ah, AR5K_PCICFG, led);
+	else
+		AR5K_REG_ENABLE_BITS(ah, AR5K_PCICFG, led_5210);
+}
+
+/**
+ * ath5k_hw_set_gpio_input() - Set GPIO inputs
+ * @ah: The &struct ath5k_hw
+ * @gpio: GPIO pin to set as input
+ */
+int
+ath5k_hw_set_gpio_input(struct ath5k_hw *ah, u32 gpio)
+{
+	if (gpio >= AR5K_NUM_GPIO)
+		return -EINVAL;
+
+	ath5k_hw_reg_write(ah,
+		(ath5k_hw_reg_read(ah, AR5K_GPIOCR) & ~AR5K_GPIOCR_OUT(gpio))
+		| AR5K_GPIOCR_IN(gpio), AR5K_GPIOCR);
+
+	return 0;
+}
+
+/**
+ * ath5k_hw_set_gpio_output() - Set GPIO outputs
+ * @ah: The &struct ath5k_hw
+ * @gpio: The GPIO pin to set as output
+ */
+int
+ath5k_hw_set_gpio_output(struct ath5k_hw *ah, u32 gpio)
+{
+	if (gpio >= AR5K_NUM_GPIO)
+		return -EINVAL;
+
+	ath5k_hw_reg_write(ah,
+		(ath5k_hw_reg_read(ah, AR5K_GPIOCR) & ~AR5K_GPIOCR_OUT(gpio))
+		| AR5K_GPIOCR_OUT(gpio), AR5K_GPIOCR);
+
+	return 0;
+}
+
+/**
+ * ath5k_hw_get_gpio() - Get GPIO state
+ * @ah: The &struct ath5k_hw
+ * @gpio: The GPIO pin to read
+ */
+u32
+ath5k_hw_get_gpio(struct ath5k_hw *ah, u32 gpio)
+{
+	if (gpio >= AR5K_NUM_GPIO)
+		return 0xffffffff;
+
+	/* GPIO input magic */
+	return ((ath5k_hw_reg_read(ah, AR5K_GPIODI) & AR5K_GPIODI_M) >> gpio) &
+		0x1;
+}
+
+/**
+ * ath5k_hw_set_gpio() - Set GPIO state
+ * @ah: The &struct ath5k_hw
+ * @gpio: The GPIO pin to set
+ * @val: Value to set (boolean)
+ */
+int
+ath5k_hw_set_gpio(struct ath5k_hw *ah, u32 gpio, u32 val)
+{
+	u32 data;
+
+	if (gpio >= AR5K_NUM_GPIO)
+		return -EINVAL;
+
+	/* GPIO output magic */
+	data = ath5k_hw_reg_read(ah, AR5K_GPIODO);
+
+	data &= ~(1 << gpio);
+	data |= (val & 1) << gpio;
+
+	ath5k_hw_reg_write(ah, data, AR5K_GPIODO);
+
+	return 0;
+}
+
+/**
+ * ath5k_hw_set_gpio_intr() - Initialize the GPIO interrupt (RFKill switch)
+ * @ah: The &struct ath5k_hw
+ * @gpio: The GPIO pin to use
+ * @interrupt_level: True to generate interrupt on active pin (high)
+ *
+ * This function is used to set up the GPIO interrupt for the hw RFKill switch.
+ * That switch is connected to a GPIO pin and it's number is stored on EEPROM.
+ * It can either open or close the circuit to indicate that we should disable
+ * RF/Wireless to save power (we also get that from EEPROM).
+ */
+void
+ath5k_hw_set_gpio_intr(struct ath5k_hw *ah, unsigned int gpio,
+		u32 interrupt_level)
+{
+	u32 data;
+
+	if (gpio >= AR5K_NUM_GPIO)
+		return;
+
+	/*
+	 * Set the GPIO interrupt
+	 */
+	data = (ath5k_hw_reg_read(ah, AR5K_GPIOCR) &
+		~(AR5K_GPIOCR_INT_SEL(gpio) | AR5K_GPIOCR_INT_SELH |
+		AR5K_GPIOCR_INT_ENA | AR5K_GPIOCR_OUT(gpio))) |
+		(AR5K_GPIOCR_INT_SEL(gpio) | AR5K_GPIOCR_INT_ENA);
+
+	ath5k_hw_reg_write(ah, interrupt_level ? data :
+		(data | AR5K_GPIOCR_INT_SELH), AR5K_GPIOCR);
+
+	ah->ah_imr |= AR5K_IMR_GPIO;
+
+	/* Enable GPIO interrupts */
+	AR5K_REG_ENABLE_BITS(ah, AR5K_PIMR, AR5K_IMR_GPIO);
+}
+

linux-7.2.3/drivers/net/wireless/ath/ath5k/led.c

@@ -0,0 +1,204 @@
+/*
+ * Copyright (c) 2002-2005 Sam Leffler, Errno Consulting
+ * Copyright (c) 2004-2005 Atheros Communications, Inc.
+ * Copyright (c) 2007 Jiri Slaby <jirislaby@gmail.com>
+ * Copyright (c) 2009 Bob Copeland <me@bobcopeland.com>
+ *
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer,
+ *    without modification.
+ * 2. Redistributions in binary form must reproduce at minimum a disclaimer
+ *    similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
+ *    redistribution must be conditioned upon including a substantially
+ *    similar Disclaimer requirement for further binary redistribution.
+ * 3. Neither the names of the above-listed copyright holders nor the names
+ *    of any contributors may be used to endorse or promote products derived
+ *    from this software without specific prior written permission.
+ *
+ * Alternatively, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") version 2 as published by the Free
+ * Software Foundation.
+ *
+ * NO WARRANTY
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
+ * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
+ * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
+ * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
+ * THE POSSIBILITY OF SUCH DAMAGES.
+ *
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/pci.h>
+#include "ath5k.h"
+
+#define ATH_SDEVICE(subv, subd) \
+	.vendor = PCI_ANY_ID, .device = PCI_ANY_ID, \
+	.subvendor = (subv), .subdevice = (subd)
+
+#define ATH_LED(pin, polarity) .driver_data = (((pin) << 8) | (polarity))
+#define ATH_PIN(data) ((data) >> 8)
+#define ATH_POLARITY(data) ((data) & 0xff)
+
+/* Devices we match on for LED config info (typically laptops) */
+static const struct pci_device_id ath5k_led_devices[] = {
+	/* AR5211 */
+	{ PCI_VDEVICE(ATHEROS, PCI_DEVICE_ID_ATHEROS_AR5211), ATH_LED(0, 0) },
+	/* HP Compaq nc6xx, nc4000, nx6000 */
+	{ ATH_SDEVICE(PCI_VENDOR_ID_COMPAQ, PCI_ANY_ID), ATH_LED(1, 1) },
+	/* Acer Aspire One A150 (maximlevitsky@gmail.com) */
+	{ ATH_SDEVICE(PCI_VENDOR_ID_FOXCONN, 0xe008), ATH_LED(3, 0) },
+	/* Acer Aspire One AO531h AO751h (keng-yu.lin@canonical.com) */
+	{ ATH_SDEVICE(PCI_VENDOR_ID_FOXCONN, 0xe00d), ATH_LED(3, 0) },
+	/* Acer Ferrari 5000 (russ.dill@gmail.com) */
+	{ ATH_SDEVICE(PCI_VENDOR_ID_AMBIT, 0x0422), ATH_LED(1, 1) },
+	/* E-machines E510 (tuliom@gmail.com) */
+	{ ATH_SDEVICE(PCI_VENDOR_ID_AMBIT, 0x0428), ATH_LED(3, 0) },
+	/* BenQ Joybook R55v (nowymarluk@wp.pl) */
+	{ ATH_SDEVICE(PCI_VENDOR_ID_QMI, 0x0100), ATH_LED(1, 0) },
+	/* Acer Extensa 5620z (nekoreeve@gmail.com) */
+	{ ATH_SDEVICE(PCI_VENDOR_ID_QMI, 0x0105), ATH_LED(3, 0) },
+	/* Fukato Datacask Jupiter 1014a (mrb74@gmx.at) */
+	{ ATH_SDEVICE(PCI_VENDOR_ID_AZWAVE, 0x1026), ATH_LED(3, 0) },
+	/* IBM ThinkPad AR5BXB6 (legovini@spiro.fisica.unipd.it) */
+	{ ATH_SDEVICE(PCI_VENDOR_ID_IBM, 0x058a), ATH_LED(1, 0) },
+	/* HP Compaq CQ60-206US (ddreggors@jumptv.com) */
+	{ ATH_SDEVICE(PCI_VENDOR_ID_HP, 0x0137a), ATH_LED(3, 1) },
+	/* HP Compaq C700 (nitrousnrg@gmail.com) */
+	{ ATH_SDEVICE(PCI_VENDOR_ID_HP, 0x0137b), ATH_LED(3, 0) },
+	/* LiteOn AR5BXB63 (magooz@salug.it) */
+	{ ATH_SDEVICE(PCI_VENDOR_ID_ATHEROS, 0x3067), ATH_LED(3, 0) },
+	/* IBM-specific AR5212 (all others) */
+	{ PCI_VDEVICE(ATHEROS, PCI_DEVICE_ID_ATHEROS_AR5212_IBM), ATH_LED(0, 0) },
+	/* Dell Vostro A860 (shahar@shahar-or.co.il) */
+	{ ATH_SDEVICE(PCI_VENDOR_ID_QMI, 0x0112), ATH_LED(3, 0) },
+	{ }
+};
+
+void ath5k_led_enable(struct ath5k_hw *ah)
+{
+	if (IS_ENABLED(CONFIG_MAC80211_LEDS) &&
+	    test_bit(ATH_STAT_LEDSOFT, ah->status)) {
+		ath5k_hw_set_gpio_output(ah, ah->led_pin);
+		ath5k_led_off(ah);
+	}
+}
+
+static void ath5k_led_on(struct ath5k_hw *ah)
+{
+	if (!test_bit(ATH_STAT_LEDSOFT, ah->status))
+		return;
+	ath5k_hw_set_gpio(ah, ah->led_pin, ah->led_on);
+}
+
+void ath5k_led_off(struct ath5k_hw *ah)
+{
+	if (!IS_ENABLED(CONFIG_MAC80211_LEDS) ||
+	    !test_bit(ATH_STAT_LEDSOFT, ah->status))
+		return;
+	ath5k_hw_set_gpio(ah, ah->led_pin, !ah->led_on);
+}
+
+static void
+ath5k_led_brightness_set(struct led_classdev *led_dev,
+	enum led_brightness brightness)
+{
+	struct ath5k_led *led = container_of(led_dev, struct ath5k_led,
+		led_dev);
+
+	if (brightness == LED_OFF)
+		ath5k_led_off(led->ah);
+	else
+		ath5k_led_on(led->ah);
+}
+
+static int
+ath5k_register_led(struct ath5k_hw *ah, struct ath5k_led *led,
+		   const char *name, const char *trigger)
+{
+	int err;
+
+	led->ah = ah;
+	strscpy(led->name, name, sizeof(led->name));
+	led->led_dev.name = led->name;
+	led->led_dev.default_trigger = trigger;
+	led->led_dev.brightness_set = ath5k_led_brightness_set;
+
+	err = led_classdev_register(ah->dev, &led->led_dev);
+	if (err) {
+		ATH5K_WARN(ah, "could not register LED %s\n", name);
+		led->ah = NULL;
+	}
+	return err;
+}
+
+static void
+ath5k_unregister_led(struct ath5k_led *led)
+{
+	if (!IS_ENABLED(CONFIG_MAC80211_LEDS) || !led->ah)
+		return;
+	led_classdev_unregister(&led->led_dev);
+	ath5k_led_off(led->ah);
+	led->ah = NULL;
+}
+
+void ath5k_unregister_leds(struct ath5k_hw *ah)
+{
+	ath5k_unregister_led(&ah->rx_led);
+	ath5k_unregister_led(&ah->tx_led);
+}
+
+int ath5k_init_leds(struct ath5k_hw *ah)
+{
+	int ret = 0;
+	struct ieee80211_hw *hw = ah->hw;
+#ifndef CONFIG_ATH5K_AHB
+	struct pci_dev *pdev = ah->pdev;
+#endif
+	char name[ATH5K_LED_MAX_NAME_LEN + 1];
+	const struct pci_device_id *match;
+
+	if (!IS_ENABLED(CONFIG_MAC80211_LEDS) || !ah->pdev)
+		return 0;
+
+#ifdef CONFIG_ATH5K_AHB
+	match = NULL;
+#else
+	match = pci_match_id(&ath5k_led_devices[0], pdev);
+#endif
+	if (match) {
+		__set_bit(ATH_STAT_LEDSOFT, ah->status);
+		ah->led_pin = ATH_PIN(match->driver_data);
+		ah->led_on = ATH_POLARITY(match->driver_data);
+	}
+
+	if (!test_bit(ATH_STAT_LEDSOFT, ah->status))
+		goto out;
+
+	ath5k_led_enable(ah);
+
+	snprintf(name, sizeof(name), "ath5k-%s::rx", wiphy_name(hw->wiphy));
+	ret = ath5k_register_led(ah, &ah->rx_led, name,
+		ieee80211_get_rx_led_name(hw));
+	if (ret)
+		goto out;
+
+	snprintf(name, sizeof(name), "ath5k-%s::tx", wiphy_name(hw->wiphy));
+	ret = ath5k_register_led(ah, &ah->tx_led, name,
+		ieee80211_get_tx_led_name(hw));
+out:
+	return ret;
+}
+

linux-7.2.3/drivers/net/wireless/ath/ath5k/mac80211-ops.c

@@ -0,0 +1,829 @@
+/*-
+ * Copyright (c) 2002-2005 Sam Leffler, Errno Consulting
+ * Copyright (c) 2004-2005 Atheros Communications, Inc.
+ * Copyright (c) 2006 Devicescape Software, Inc.
+ * Copyright (c) 2007 Jiri Slaby <jirislaby@gmail.com>
+ * Copyright (c) 2007 Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
+ * Copyright (c) 2010 Bruno Randolf <br1@einfach.org>
+ *
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer,
+ *    without modification.
+ * 2. Redistributions in binary form must reproduce at minimum a disclaimer
+ *    similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
+ *    redistribution must be conditioned upon including a substantially
+ *    similar Disclaimer requirement for further binary redistribution.
+ * 3. Neither the names of the above-listed copyright holders nor the names
+ *    of any contributors may be used to endorse or promote products derived
+ *    from this software without specific prior written permission.
+ *
+ * Alternatively, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") version 2 as published by the Free
+ * Software Foundation.
+ *
+ * NO WARRANTY
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
+ * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
+ * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
+ * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
+ * THE POSSIBILITY OF SUCH DAMAGES.
+ *
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <net/mac80211.h>
+#include <linux/unaligned.h>
+
+#include "ath5k.h"
+#include "base.h"
+#include "reg.h"
+
+/********************\
+* Mac80211 functions *
+\********************/
+
+static void
+ath5k_tx(struct ieee80211_hw *hw, struct ieee80211_tx_control *control,
+	 struct sk_buff *skb)
+{
+	struct ath5k_hw *ah = hw->priv;
+	u16 qnum = skb_get_queue_mapping(skb);
+
+	if (WARN_ON(qnum >= ah->ah_capabilities.cap_queues.q_tx_num)) {
+		ieee80211_free_txskb(hw, skb);
+		return;
+	}
+
+	ath5k_tx_queue(hw, skb, &ah->txqs[qnum], control);
+}
+
+
+static int
+ath5k_add_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif)
+{
+	struct ath5k_hw *ah = hw->priv;
+	int ret;
+	struct ath5k_vif *avf = (void *)vif->drv_priv;
+
+	mutex_lock(&ah->lock);
+
+	if ((vif->type == NL80211_IFTYPE_AP ||
+	     vif->type == NL80211_IFTYPE_ADHOC)
+	    && (ah->num_ap_vifs + ah->num_adhoc_vifs) >= ATH_BCBUF) {
+		ret = -ELNRNG;
+		goto end;
+	}
+
+	/* Don't allow other interfaces if one ad-hoc is configured.
+	 * TODO: Fix the problems with ad-hoc and multiple other interfaces.
+	 * We would need to operate the HW in ad-hoc mode to allow TSF updates
+	 * for the IBSS, but this breaks with additional AP or STA interfaces
+	 * at the moment. */
+	if (ah->num_adhoc_vifs ||
+	    (ah->nvifs && vif->type == NL80211_IFTYPE_ADHOC)) {
+		ATH5K_ERR(ah, "Only one single ad-hoc interface is allowed.\n");
+		ret = -ELNRNG;
+		goto end;
+	}
+
+	switch (vif->type) {
+	case NL80211_IFTYPE_AP:
+	case NL80211_IFTYPE_STATION:
+	case NL80211_IFTYPE_ADHOC:
+	case NL80211_IFTYPE_MESH_POINT:
+		avf->opmode = vif->type;
+		break;
+	default:
+		ret = -EOPNOTSUPP;
+		goto end;
+	}
+
+	ah->nvifs++;
+	ATH5K_DBG(ah, ATH5K_DEBUG_MODE, "add interface mode %d\n", avf->opmode);
+
+	/* Assign the vap/adhoc to a beacon xmit slot. */
+	if ((avf->opmode == NL80211_IFTYPE_AP) ||
+	    (avf->opmode == NL80211_IFTYPE_ADHOC) ||
+	    (avf->opmode == NL80211_IFTYPE_MESH_POINT)) {
+		int slot;
+
+		WARN_ON(list_empty(&ah->bcbuf));
+		avf->bbuf = list_first_entry(&ah->bcbuf, struct ath5k_buf,
+					     list);
+		list_del(&avf->bbuf->list);
+
+		avf->bslot = 0;
+		for (slot = 0; slot < ATH_BCBUF; slot++) {
+			if (!ah->bslot[slot]) {
+				avf->bslot = slot;
+				break;
+			}
+		}
+		BUG_ON(ah->bslot[avf->bslot] != NULL);
+		ah->bslot[avf->bslot] = vif;
+		if (avf->opmode == NL80211_IFTYPE_AP)
+			ah->num_ap_vifs++;
+		else if (avf->opmode == NL80211_IFTYPE_ADHOC)
+			ah->num_adhoc_vifs++;
+		else if (avf->opmode == NL80211_IFTYPE_MESH_POINT)
+			ah->num_mesh_vifs++;
+	}
+
+	/* Any MAC address is fine, all others are included through the
+	 * filter.
+	 */
+	ath5k_hw_set_lladdr(ah, vif->addr);
+
+	ath5k_update_bssid_mask_and_opmode(ah, vif);
+	ret = 0;
+end:
+	mutex_unlock(&ah->lock);
+	return ret;
+}
+
+
+static void
+ath5k_remove_interface(struct ieee80211_hw *hw,
+		       struct ieee80211_vif *vif)
+{
+	struct ath5k_hw *ah = hw->priv;
+	struct ath5k_vif *avf = (void *)vif->drv_priv;
+	unsigned int i;
+
+	mutex_lock(&ah->lock);
+	ah->nvifs--;
+
+	if (avf->bbuf) {
+		ath5k_txbuf_free_skb(ah, avf->bbuf);
+		list_add_tail(&avf->bbuf->list, &ah->bcbuf);
+		for (i = 0; i < ATH_BCBUF; i++) {
+			if (ah->bslot[i] == vif) {
+				ah->bslot[i] = NULL;
+				break;
+			}
+		}
+		avf->bbuf = NULL;
+	}
+	if (avf->opmode == NL80211_IFTYPE_AP)
+		ah->num_ap_vifs--;
+	else if (avf->opmode == NL80211_IFTYPE_ADHOC)
+		ah->num_adhoc_vifs--;
+	else if (avf->opmode == NL80211_IFTYPE_MESH_POINT)
+		ah->num_mesh_vifs--;
+
+	ath5k_update_bssid_mask_and_opmode(ah, NULL);
+	mutex_unlock(&ah->lock);
+}
+
+
+/*
+ * TODO: Phy disable/diversity etc
+ */
+static int
+ath5k_config(struct ieee80211_hw *hw, int radio_idx, u32 changed)
+{
+	struct ath5k_hw *ah = hw->priv;
+	struct ieee80211_conf *conf = &hw->conf;
+	int ret = 0;
+	int i;
+
+	mutex_lock(&ah->lock);
+
+	if (changed & IEEE80211_CONF_CHANGE_CHANNEL) {
+		ret = ath5k_chan_set(ah, &conf->chandef);
+		if (ret < 0)
+			goto unlock;
+	}
+
+	if ((changed & IEEE80211_CONF_CHANGE_POWER) &&
+	(ah->ah_txpower.txp_requested != conf->power_level)) {
+		ah->ah_txpower.txp_requested = conf->power_level;
+
+		/* Half dB steps */
+		ath5k_hw_set_txpower_limit(ah, (conf->power_level * 2));
+	}
+
+	if (changed & IEEE80211_CONF_CHANGE_RETRY_LIMITS) {
+		ah->ah_retry_long = conf->long_frame_max_tx_count;
+		ah->ah_retry_short = conf->short_frame_max_tx_count;
+
+		for (i = 0; i < ah->ah_capabilities.cap_queues.q_tx_num; i++)
+			ath5k_hw_set_tx_retry_limits(ah, i);
+	}
+
+	/* TODO:
+	 * 1) Move this on config_interface and handle each case
+	 * separately eg. when we have only one STA vif, use
+	 * AR5K_ANTMODE_SINGLE_AP
+	 *
+	 * 2) Allow the user to change antenna mode eg. when only
+	 * one antenna is present
+	 *
+	 * 3) Allow the user to set default/tx antenna when possible
+	 *
+	 * 4) Default mode should handle 90% of the cases, together
+	 * with fixed a/b and single AP modes we should be able to
+	 * handle 99%. Sectored modes are extreme cases and i still
+	 * haven't found a usage for them. If we decide to support them,
+	 * then we must allow the user to set how many tx antennas we
+	 * have available
+	 */
+	ath5k_hw_set_antenna_mode(ah, ah->ah_ant_mode);
+
+unlock:
+	mutex_unlock(&ah->lock);
+	return ret;
+}
+
+
+static void
+ath5k_bss_info_changed(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+		       struct ieee80211_bss_conf *bss_conf, u64 changes)
+{
+	struct ath5k_vif *avf = (void *)vif->drv_priv;
+	struct ath5k_hw *ah = hw->priv;
+	struct ath_common *common = ath5k_hw_common(ah);
+
+	mutex_lock(&ah->lock);
+
+	if (changes & BSS_CHANGED_BSSID) {
+		/* Cache for later use during resets */
+		memcpy(common->curbssid, bss_conf->bssid, ETH_ALEN);
+		common->curaid = 0;
+		ath5k_hw_set_bssid(ah);
+	}
+
+	if (changes & BSS_CHANGED_BEACON_INT)
+		ah->bintval = bss_conf->beacon_int;
+
+	if (changes & BSS_CHANGED_ERP_SLOT) {
+		int slot_time;
+
+		ah->ah_short_slot = bss_conf->use_short_slot;
+		slot_time = ath5k_hw_get_default_slottime(ah) +
+			    3 * ah->ah_coverage_class;
+		ath5k_hw_set_ifs_intervals(ah, slot_time);
+	}
+
+	if (changes & BSS_CHANGED_ASSOC) {
+		avf->assoc = vif->cfg.assoc;
+		if (vif->cfg.assoc)
+			ah->assoc = vif->cfg.assoc;
+		else
+			ah->assoc = ath5k_any_vif_assoc(ah);
+
+		if (ah->opmode == NL80211_IFTYPE_STATION)
+			ath5k_set_beacon_filter(hw, ah->assoc);
+		ath5k_hw_set_ledstate(ah, ah->assoc ?
+			AR5K_LED_ASSOC : AR5K_LED_INIT);
+		if (vif->cfg.assoc) {
+			ATH5K_DBG(ah, ATH5K_DEBUG_ANY,
+				  "Bss Info ASSOC %d, bssid: %pM\n",
+				  vif->cfg.aid, common->curbssid);
+			common->curaid = vif->cfg.aid;
+			ath5k_hw_set_bssid(ah);
+			/* Once ANI is available you would start it here */
+		}
+	}
+
+	if (changes & BSS_CHANGED_BEACON) {
+		spin_lock_bh(&ah->block);
+		ath5k_beacon_update(hw, vif);
+		spin_unlock_bh(&ah->block);
+	}
+
+	if (changes & BSS_CHANGED_BEACON_ENABLED)
+		ah->enable_beacon = bss_conf->enable_beacon;
+
+	if (changes & (BSS_CHANGED_BEACON | BSS_CHANGED_BEACON_ENABLED |
+		       BSS_CHANGED_BEACON_INT))
+		ath5k_beacon_config(ah);
+
+	mutex_unlock(&ah->lock);
+}
+
+
+static u64
+ath5k_prepare_multicast(struct ieee80211_hw *hw,
+			struct netdev_hw_addr_list *mc_list)
+{
+	u32 mfilt[2], val;
+	u8 pos;
+	struct netdev_hw_addr *ha;
+
+	mfilt[0] = 0;
+	mfilt[1] = 0;
+
+	netdev_hw_addr_list_for_each(ha, mc_list) {
+		/* calculate XOR of eight 6-bit values */
+		val = get_unaligned_le32(ha->addr + 0);
+		pos = (val >> 18) ^ (val >> 12) ^ (val >> 6) ^ val;
+		val = get_unaligned_le32(ha->addr + 3);
+		pos ^= (val >> 18) ^ (val >> 12) ^ (val >> 6) ^ val;
+		pos &= 0x3f;
+		mfilt[pos / 32] |= (1 << (pos % 32));
+		/* XXX: we might be able to just do this instead,
+		* but not sure, needs testing, if we do use this we'd
+		* need to inform below not to reset the mcast */
+		/* ath5k_hw_set_mcast_filterindex(ah,
+		 *      ha->addr[5]); */
+	}
+
+	return ((u64)(mfilt[1]) << 32) | mfilt[0];
+}
+
+
+/*
+ * o always accept unicast, broadcast, and multicast traffic
+ * o multicast traffic for all BSSIDs will be enabled if mac80211
+ *   says it should be
+ * o maintain current state of phy ofdm or phy cck error reception.
+ *   If the hardware detects any of these type of errors then
+ *   ath5k_hw_get_rx_filter() will pass to us the respective
+ *   hardware filters to be able to receive these type of frames.
+ * o probe request frames are accepted only when operating in
+ *   hostap, adhoc, or monitor modes
+ * o enable promiscuous mode according to the interface state
+ * o accept beacons:
+ *   - when operating in adhoc mode so the 802.11 layer creates
+ *     node table entries for peers,
+ *   - when operating in station mode for collecting rssi data when
+ *     the station is otherwise quiet, or
+ *   - when scanning
+ */
+static void
+ath5k_configure_filter(struct ieee80211_hw *hw, unsigned int changed_flags,
+		       unsigned int *new_flags, u64 multicast)
+{
+#define SUPPORTED_FIF_FLAGS \
+	(FIF_ALLMULTI | FIF_FCSFAIL | \
+	FIF_PLCPFAIL | FIF_CONTROL | FIF_OTHER_BSS | \
+	FIF_BCN_PRBRESP_PROMISC)
+
+	struct ath5k_hw *ah = hw->priv;
+	u32 mfilt[2], rfilt;
+	struct ath5k_vif_iter_data iter_data; /* to count STA interfaces */
+
+	mutex_lock(&ah->lock);
+
+	mfilt[0] = multicast;
+	mfilt[1] = multicast >> 32;
+
+	/* Only deal with supported flags */
+	*new_flags &= SUPPORTED_FIF_FLAGS;
+
+	/* If HW detects any phy or radar errors, leave those filters on.
+	 * Also, always enable Unicast, Broadcasts and Multicast
+	 * XXX: move unicast, bssid broadcasts and multicast to mac80211 */
+	rfilt = (ath5k_hw_get_rx_filter(ah) & (AR5K_RX_FILTER_PHYERR)) |
+		(AR5K_RX_FILTER_UCAST | AR5K_RX_FILTER_BCAST |
+		AR5K_RX_FILTER_MCAST);
+
+	/* Note, AR5K_RX_FILTER_MCAST is already enabled */
+	if (*new_flags & FIF_ALLMULTI) {
+		mfilt[0] =  ~0;
+		mfilt[1] =  ~0;
+	}
+
+	/* This is the best we can do */
+	if (*new_flags & (FIF_FCSFAIL | FIF_PLCPFAIL))
+		rfilt |= AR5K_RX_FILTER_PHYERR;
+
+	/* FIF_BCN_PRBRESP_PROMISC really means to enable beacons
+	* and probes for any BSSID */
+	if ((*new_flags & FIF_BCN_PRBRESP_PROMISC) || (ah->nvifs > 1))
+		rfilt |= AR5K_RX_FILTER_BEACON;
+
+	/* FIF_CONTROL doc says we should only pass on control frames for this
+	 * station. This needs testing. I believe right now this
+	 * enables *all* control frames, which is OK.. but
+	 * we should see if we can improve on granularity */
+	if (*new_flags & FIF_CONTROL)
+		rfilt |= AR5K_RX_FILTER_CONTROL;
+
+	/* Additional settings per mode -- this is per ath5k */
+
+	/* XXX move these to mac80211, and add a beacon IFF flag to mac80211 */
+
+	switch (ah->opmode) {
+	case NL80211_IFTYPE_MESH_POINT:
+		rfilt |= AR5K_RX_FILTER_CONTROL |
+			 AR5K_RX_FILTER_BEACON |
+			 AR5K_RX_FILTER_PROBEREQ |
+			 AR5K_RX_FILTER_PROM;
+		break;
+	case NL80211_IFTYPE_AP:
+	case NL80211_IFTYPE_ADHOC:
+		rfilt |= AR5K_RX_FILTER_PROBEREQ |
+			 AR5K_RX_FILTER_BEACON;
+		break;
+	case NL80211_IFTYPE_STATION:
+		if (ah->assoc)
+			rfilt |= AR5K_RX_FILTER_BEACON;
+		break;
+	default:
+		break;
+	}
+
+	iter_data.hw_macaddr = NULL;
+	iter_data.n_stas = 0;
+	iter_data.need_set_hw_addr = false;
+	ieee80211_iterate_active_interfaces_atomic(
+		ah->hw, IEEE80211_IFACE_ITER_RESUME_ALL,
+		ath5k_vif_iter, &iter_data);
+
+	/* Set up RX Filter */
+	if (iter_data.n_stas > 1) {
+		/* If you have multiple STA interfaces connected to
+		 * different APs, ARPs are not received (most of the time?)
+		 * Enabling PROMISC appears to fix that problem.
+		 */
+		rfilt |= AR5K_RX_FILTER_PROM;
+	}
+
+	/* Set filters */
+	ath5k_hw_set_rx_filter(ah, rfilt);
+
+	/* Set multicast bits */
+	ath5k_hw_set_mcast_filter(ah, mfilt[0], mfilt[1]);
+	/* Set the cached hw filter flags, this will later actually
+	 * be set in HW */
+	ah->filter_flags = rfilt;
+	/* Store current FIF filter flags */
+	ah->fif_filter_flags = *new_flags;
+
+	mutex_unlock(&ah->lock);
+}
+
+
+static int
+ath5k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
+	      struct ieee80211_vif *vif, struct ieee80211_sta *sta,
+	      struct ieee80211_key_conf *key)
+{
+	struct ath5k_hw *ah = hw->priv;
+	struct ath_common *common = ath5k_hw_common(ah);
+	int ret = 0;
+
+	if (ath5k_modparam_nohwcrypt)
+		return -EOPNOTSUPP;
+
+	if (key->flags & IEEE80211_KEY_FLAG_RX_MGMT)
+		return -EOPNOTSUPP;
+
+	if (vif->type == NL80211_IFTYPE_ADHOC &&
+	    (key->cipher == WLAN_CIPHER_SUITE_TKIP ||
+	     key->cipher == WLAN_CIPHER_SUITE_CCMP) &&
+	    !(key->flags & IEEE80211_KEY_FLAG_PAIRWISE)) {
+		/* don't program group keys when using IBSS_RSN */
+		return -EOPNOTSUPP;
+	}
+
+	switch (key->cipher) {
+	case WLAN_CIPHER_SUITE_WEP40:
+	case WLAN_CIPHER_SUITE_WEP104:
+	case WLAN_CIPHER_SUITE_TKIP:
+		break;
+	case WLAN_CIPHER_SUITE_CCMP:
+		if (common->crypt_caps & ATH_CRYPT_CAP_CIPHER_AESCCM)
+			break;
+		return -EOPNOTSUPP;
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	mutex_lock(&ah->lock);
+
+	switch (cmd) {
+	case SET_KEY:
+		ret = ath_key_config(common, vif, sta, key);
+		if (ret >= 0) {
+			key->hw_key_idx = ret;
+			/* push IV and Michael MIC generation to stack */
+			key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
+			if (key->cipher == WLAN_CIPHER_SUITE_TKIP)
+				key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC;
+			if (key->cipher == WLAN_CIPHER_SUITE_CCMP)
+				key->flags |= IEEE80211_KEY_FLAG_SW_MGMT_TX;
+			ret = 0;
+		}
+		break;
+	case DISABLE_KEY:
+		ath_key_delete(common, key->hw_key_idx);
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	mutex_unlock(&ah->lock);
+	return ret;
+}
+
+
+static void
+ath5k_sw_scan_start(struct ieee80211_hw *hw,
+		    struct ieee80211_vif *vif,
+		    const u8 *mac_addr)
+{
+	struct ath5k_hw *ah = hw->priv;
+	if (!ah->assoc)
+		ath5k_hw_set_ledstate(ah, AR5K_LED_SCAN);
+}
+
+
+static void
+ath5k_sw_scan_complete(struct ieee80211_hw *hw, struct ieee80211_vif *vif)
+{
+	struct ath5k_hw *ah = hw->priv;
+	ath5k_hw_set_ledstate(ah, ah->assoc ?
+		AR5K_LED_ASSOC : AR5K_LED_INIT);
+}
+
+
+static int
+ath5k_get_stats(struct ieee80211_hw *hw,
+		struct ieee80211_low_level_stats *stats)
+{
+	struct ath5k_hw *ah = hw->priv;
+
+	/* Force update */
+	ath5k_hw_update_mib_counters(ah);
+
+	stats->dot11ACKFailureCount = ah->stats.ack_fail;
+	stats->dot11RTSFailureCount = ah->stats.rts_fail;
+	stats->dot11RTSSuccessCount = ah->stats.rts_ok;
+	stats->dot11FCSErrorCount = ah->stats.fcs_error;
+
+	return 0;
+}
+
+
+static int
+ath5k_conf_tx(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+	      unsigned int link_id, u16 queue,
+	      const struct ieee80211_tx_queue_params *params)
+{
+	struct ath5k_hw *ah = hw->priv;
+	struct ath5k_txq_info qi;
+	int ret = 0;
+
+	if (queue >= ah->ah_capabilities.cap_queues.q_tx_num)
+		return 0;
+
+	mutex_lock(&ah->lock);
+
+	ath5k_hw_get_tx_queueprops(ah, queue, &qi);
+
+	qi.tqi_aifs = params->aifs;
+	qi.tqi_cw_min = params->cw_min;
+	qi.tqi_cw_max = params->cw_max;
+	qi.tqi_burst_time = params->txop * 32;
+
+	ATH5K_DBG(ah, ATH5K_DEBUG_ANY,
+		  "Configure tx [queue %d],  "
+		  "aifs: %d, cw_min: %d, cw_max: %d, txop: %d\n",
+		  queue, params->aifs, params->cw_min,
+		  params->cw_max, params->txop);
+
+	if (ath5k_hw_set_tx_queueprops(ah, queue, &qi)) {
+		ATH5K_ERR(ah,
+			  "Unable to update hardware queue %u!\n", queue);
+		ret = -EIO;
+	} else
+		ath5k_hw_reset_tx_queue(ah, queue);
+
+	mutex_unlock(&ah->lock);
+
+	return ret;
+}
+
+
+static u64
+ath5k_get_tsf(struct ieee80211_hw *hw, struct ieee80211_vif *vif)
+{
+	struct ath5k_hw *ah = hw->priv;
+
+	return ath5k_hw_get_tsf64(ah);
+}
+
+
+static void
+ath5k_set_tsf(struct ieee80211_hw *hw, struct ieee80211_vif *vif, u64 tsf)
+{
+	struct ath5k_hw *ah = hw->priv;
+
+	ath5k_hw_set_tsf64(ah, tsf);
+}
+
+
+static void
+ath5k_reset_tsf(struct ieee80211_hw *hw, struct ieee80211_vif *vif)
+{
+	struct ath5k_hw *ah = hw->priv;
+
+	/*
+	 * in IBSS mode we need to update the beacon timers too.
+	 * this will also reset the TSF if we call it with 0
+	 */
+	if (ah->opmode == NL80211_IFTYPE_ADHOC)
+		ath5k_beacon_update_timers(ah, 0);
+	else
+		ath5k_hw_reset_tsf(ah);
+}
+
+
+static int
+ath5k_get_survey(struct ieee80211_hw *hw, int idx, struct survey_info *survey)
+{
+	struct ath5k_hw *ah = hw->priv;
+	struct ieee80211_conf *conf = &hw->conf;
+	struct ath_common *common = ath5k_hw_common(ah);
+	struct ath_cycle_counters *cc = &common->cc_survey;
+	unsigned int div = common->clockrate * 1000;
+
+	if (idx != 0)
+		return -ENOENT;
+
+	spin_lock_bh(&common->cc_lock);
+	ath_hw_cycle_counters_update(common);
+	if (cc->cycles > 0) {
+		ah->survey.time += cc->cycles / div;
+		ah->survey.time_busy += cc->rx_busy / div;
+		ah->survey.time_rx += cc->rx_frame / div;
+		ah->survey.time_tx += cc->tx_frame / div;
+	}
+	memset(cc, 0, sizeof(*cc));
+	spin_unlock_bh(&common->cc_lock);
+
+	memcpy(survey, &ah->survey, sizeof(*survey));
+
+	survey->channel = conf->chandef.chan;
+	survey->noise = ah->ah_noise_floor;
+	survey->filled = SURVEY_INFO_NOISE_DBM |
+			SURVEY_INFO_IN_USE |
+			SURVEY_INFO_TIME |
+			SURVEY_INFO_TIME_BUSY |
+			SURVEY_INFO_TIME_RX |
+			SURVEY_INFO_TIME_TX;
+
+	return 0;
+}
+
+
+/**
+ * ath5k_set_coverage_class - Set IEEE 802.11 coverage class
+ *
+ * @hw: struct ieee80211_hw pointer
+ * @radio_idx: Radio index
+ * @coverage_class: IEEE 802.11 coverage class number
+ *
+ * Mac80211 callback. Sets slot time, ACK timeout and CTS timeout for given
+ * coverage class. The values are persistent, they are restored after device
+ * reset.
+ */
+static void
+ath5k_set_coverage_class(struct ieee80211_hw *hw, int radio_idx,
+			 s16 coverage_class)
+{
+	struct ath5k_hw *ah = hw->priv;
+
+	mutex_lock(&ah->lock);
+	ath5k_hw_set_coverage_class(ah, coverage_class);
+	mutex_unlock(&ah->lock);
+}
+
+
+static int
+ath5k_set_antenna(struct ieee80211_hw *hw, int radio_idx, u32 tx_ant,
+		  u32 rx_ant)
+{
+	struct ath5k_hw *ah = hw->priv;
+
+	if (tx_ant == 1 && rx_ant == 1)
+		ath5k_hw_set_antenna_mode(ah, AR5K_ANTMODE_FIXED_A);
+	else if (tx_ant == 2 && rx_ant == 2)
+		ath5k_hw_set_antenna_mode(ah, AR5K_ANTMODE_FIXED_B);
+	else if ((tx_ant & 3) == 3 && (rx_ant & 3) == 3)
+		ath5k_hw_set_antenna_mode(ah, AR5K_ANTMODE_DEFAULT);
+	else
+		return -EINVAL;
+	return 0;
+}
+
+
+static int
+ath5k_get_antenna(struct ieee80211_hw *hw, int radio_idx,
+		  u32 *tx_ant, u32 *rx_ant)
+{
+	struct ath5k_hw *ah = hw->priv;
+
+	switch (ah->ah_ant_mode) {
+	case AR5K_ANTMODE_FIXED_A:
+		*tx_ant = 1; *rx_ant = 1; break;
+	case AR5K_ANTMODE_FIXED_B:
+		*tx_ant = 2; *rx_ant = 2; break;
+	case AR5K_ANTMODE_DEFAULT:
+		*tx_ant = 3; *rx_ant = 3; break;
+	}
+	return 0;
+}
+
+
+static void ath5k_get_ringparam(struct ieee80211_hw *hw,
+				u32 *tx, u32 *tx_max, u32 *rx, u32 *rx_max)
+{
+	struct ath5k_hw *ah = hw->priv;
+
+	*tx = ah->txqs[AR5K_TX_QUEUE_ID_DATA_MIN].txq_max;
+
+	*tx_max = ATH5K_TXQ_LEN_MAX;
+	*rx = *rx_max = ATH_RXBUF;
+}
+
+
+static int ath5k_set_ringparam(struct ieee80211_hw *hw, u32 tx, u32 rx)
+{
+	struct ath5k_hw *ah = hw->priv;
+	u16 qnum;
+
+	/* only support setting tx ring size for now */
+	if (rx != ATH_RXBUF)
+		return -EINVAL;
+
+	/* restrict tx ring size min/max */
+	if (!tx || tx > ATH5K_TXQ_LEN_MAX)
+		return -EINVAL;
+
+	for (qnum = 0; qnum < ARRAY_SIZE(ah->txqs); qnum++) {
+		if (!ah->txqs[qnum].setup)
+			continue;
+		if (ah->txqs[qnum].qnum < AR5K_TX_QUEUE_ID_DATA_MIN ||
+		    ah->txqs[qnum].qnum > AR5K_TX_QUEUE_ID_DATA_MAX)
+			continue;
+
+		ah->txqs[qnum].txq_max = tx;
+		if (ah->txqs[qnum].txq_len >= ah->txqs[qnum].txq_max)
+			ieee80211_stop_queue(hw, ah->txqs[qnum].qnum);
+	}
+
+	return 0;
+}
+
+
+const struct ieee80211_ops ath5k_hw_ops = {
+	.add_chanctx = ieee80211_emulate_add_chanctx,
+	.remove_chanctx = ieee80211_emulate_remove_chanctx,
+	.change_chanctx = ieee80211_emulate_change_chanctx,
+	.switch_vif_chanctx = ieee80211_emulate_switch_vif_chanctx,
+	.tx			= ath5k_tx,
+	.wake_tx_queue		= ieee80211_handle_wake_tx_queue,
+	.start			= ath5k_start,
+	.stop			= ath5k_stop,
+	.add_interface		= ath5k_add_interface,
+	/* .change_interface	= not implemented */
+	.remove_interface	= ath5k_remove_interface,
+	.config			= ath5k_config,
+	.bss_info_changed	= ath5k_bss_info_changed,
+	.prepare_multicast	= ath5k_prepare_multicast,
+	.configure_filter	= ath5k_configure_filter,
+	/* .set_tim		= not implemented */
+	.set_key		= ath5k_set_key,
+	/* .update_tkip_key	= not implemented */
+	/* .hw_scan		= not implemented */
+	.sw_scan_start		= ath5k_sw_scan_start,
+	.sw_scan_complete	= ath5k_sw_scan_complete,
+	.get_stats		= ath5k_get_stats,
+	/* .set_frag_threshold	= not implemented */
+	/* .set_rts_threshold	= not implemented */
+	/* .sta_add		= not implemented */
+	/* .sta_remove		= not implemented */
+	/* .sta_notify		= not implemented */
+	.conf_tx		= ath5k_conf_tx,
+	.get_tsf		= ath5k_get_tsf,
+	.set_tsf		= ath5k_set_tsf,
+	.reset_tsf		= ath5k_reset_tsf,
+	/* .tx_last_beacon	= not implemented */
+	/* .ampdu_action	= not needed */
+	.get_survey		= ath5k_get_survey,
+	.set_coverage_class	= ath5k_set_coverage_class,
+	/* .rfkill_poll		= not implemented */
+	/* .flush		= not implemented */
+	/* .channel_switch	= not implemented */
+	/* .napi_poll		= not implemented */
+	.set_antenna		= ath5k_set_antenna,
+	.get_antenna		= ath5k_get_antenna,
+	.set_ringparam		= ath5k_set_ringparam,
+	.get_ringparam		= ath5k_get_ringparam,
+};

linux-7.2.3/drivers/net/wireless/ath/ath5k/pci.c

@@ -0,0 +1,343 @@
+/*
+ * Copyright (c) 2008-2009 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/nl80211.h>
+#include <linux/pci.h>
+#include <linux/etherdevice.h>
+#include <linux/module.h>
+#include "../ath.h"
+#include "ath5k.h"
+#include "debug.h"
+#include "base.h"
+#include "reg.h"
+
+/* Known PCI ids */
+static const struct pci_device_id ath5k_pci_id_table[] = {
+	{ PCI_VDEVICE(ATHEROS, 0x0207) }, /* 5210 early */
+	{ PCI_VDEVICE(ATHEROS, 0x0007) }, /* 5210 */
+	{ PCI_VDEVICE(ATHEROS, 0x0011) }, /* 5311 - this is on AHB bus !*/
+	{ PCI_VDEVICE(ATHEROS, 0x0012) }, /* 5211 */
+	{ PCI_VDEVICE(ATHEROS, 0x0013) }, /* 5212 */
+	{ PCI_VDEVICE(3COM_2,  0x0013) }, /* 3com 5212 */
+	{ PCI_VDEVICE(3COM,    0x0013) }, /* 3com 3CRDAG675 5212 */
+	{ PCI_VDEVICE(ATHEROS, 0x1014) }, /* IBM minipci 5212 */
+	{ PCI_VDEVICE(ATHEROS, 0x0014) }, /* 5212 compatible */
+	{ PCI_VDEVICE(ATHEROS, 0x0015) }, /* 5212 compatible */
+	{ PCI_VDEVICE(ATHEROS, 0x0016) }, /* 5212 compatible */
+	{ PCI_VDEVICE(ATHEROS, 0x0017) }, /* 5212 compatible */
+	{ PCI_VDEVICE(ATHEROS, 0x0018) }, /* 5212 compatible */
+	{ PCI_VDEVICE(ATHEROS, 0x0019) }, /* 5212 compatible */
+	{ PCI_VDEVICE(ATHEROS, 0x001a) }, /* 2413 Griffin-lite */
+	{ PCI_VDEVICE(ATHEROS, 0x001b) }, /* 5413 Eagle */
+	{ PCI_VDEVICE(ATHEROS, 0x001c) }, /* PCI-E cards */
+	{ PCI_VDEVICE(ATHEROS, 0x001d) }, /* 2417 Nala */
+	{ PCI_VDEVICE(ATHEROS, 0xff16) }, /* Gigaset SX76[23] AR241[34]A */
+	{ PCI_VDEVICE(ATHEROS, 0xff1a) }, /* Arcadyan ARV45XX AR2417 */
+	{ PCI_VDEVICE(ATHEROS, 0xff1b) }, /* AR5BXB63 */
+	{ 0 }
+};
+MODULE_DEVICE_TABLE(pci, ath5k_pci_id_table);
+
+/* return bus cachesize in 4B word units */
+static void ath5k_pci_read_cachesize(struct ath_common *common, int *csz)
+{
+	struct ath5k_hw *ah = common->priv;
+	u8 u8tmp;
+
+	pci_read_config_byte(ah->pdev, PCI_CACHE_LINE_SIZE, &u8tmp);
+	*csz = (int)u8tmp;
+
+	/*
+	 * This check was put in to avoid "unpleasant" consequences if
+	 * the bootrom has not fully initialized all PCI devices.
+	 * Sometimes the cache line size register is not set
+	 */
+
+	if (*csz == 0)
+		*csz = L1_CACHE_BYTES >> 2;   /* Use the default size */
+}
+
+/*
+ * Read from eeprom
+ */
+static bool
+ath5k_pci_eeprom_read(struct ath_common *common, u32 offset, u16 *data)
+{
+	struct ath5k_hw *ah = common->ah;
+	u32 status, timeout;
+
+	/*
+	 * Initialize EEPROM access
+	 */
+	if (ah->ah_version == AR5K_AR5210) {
+		AR5K_REG_ENABLE_BITS(ah, AR5K_PCICFG, AR5K_PCICFG_EEAE);
+		(void)ath5k_hw_reg_read(ah, AR5K_EEPROM_BASE + (4 * offset));
+	} else {
+		ath5k_hw_reg_write(ah, offset, AR5K_EEPROM_BASE);
+		AR5K_REG_ENABLE_BITS(ah, AR5K_EEPROM_CMD,
+				AR5K_EEPROM_CMD_READ);
+	}
+
+	for (timeout = AR5K_TUNE_REGISTER_TIMEOUT; timeout > 0; timeout--) {
+		status = ath5k_hw_reg_read(ah, AR5K_EEPROM_STATUS);
+		if (status & AR5K_EEPROM_STAT_RDDONE) {
+			if (status & AR5K_EEPROM_STAT_RDERR)
+				return false;
+			*data = (u16)(ath5k_hw_reg_read(ah, AR5K_EEPROM_DATA) &
+					0xffff);
+			return true;
+		}
+		usleep_range(15, 20);
+	}
+
+	return false;
+}
+
+int ath5k_hw_read_srev(struct ath5k_hw *ah)
+{
+	ah->ah_mac_srev = ath5k_hw_reg_read(ah, AR5K_SREV);
+	return 0;
+}
+
+/*
+ * Read the MAC address from eeprom or platform_data
+ */
+static int ath5k_pci_eeprom_read_mac(struct ath5k_hw *ah, u8 *mac)
+{
+	u8 mac_d[ETH_ALEN] = {};
+	u32 total, offset;
+	u16 data;
+	int octet;
+
+	AR5K_EEPROM_READ(0x20, data);
+
+	for (offset = 0x1f, octet = 0, total = 0; offset >= 0x1d; offset--) {
+		AR5K_EEPROM_READ(offset, data);
+
+		total += data;
+		mac_d[octet + 1] = data & 0xff;
+		mac_d[octet] = data >> 8;
+		octet += 2;
+	}
+
+	if (!total || total == 3 * 0xffff)
+		return -EINVAL;
+
+	memcpy(mac, mac_d, ETH_ALEN);
+
+	return 0;
+}
+
+
+/* Common ath_bus_opts structure */
+static const struct ath_bus_ops ath_pci_bus_ops = {
+	.ath_bus_type = ATH_PCI,
+	.read_cachesize = ath5k_pci_read_cachesize,
+	.eeprom_read = ath5k_pci_eeprom_read,
+	.eeprom_read_mac = ath5k_pci_eeprom_read_mac,
+};
+
+/********************\
+* PCI Initialization *
+\********************/
+
+static int
+ath5k_pci_probe(struct pci_dev *pdev,
+		const struct pci_device_id *id)
+{
+	void __iomem *mem;
+	struct ath5k_hw *ah;
+	struct ieee80211_hw *hw;
+	int ret;
+	u8 csz;
+
+	/*
+	 * L0s needs to be disabled on all ath5k cards.
+	 *
+	 * For distributions shipping with CONFIG_PCIEASPM (this will be enabled
+	 * by default in the future in 2.6.36) this will also mean both L1 and
+	 * L0s will be disabled when a pre 1.1 PCIe device is detected. We do
+	 * know L1 works correctly even for all ath5k pre 1.1 PCIe devices
+	 * though but cannot currently undue the effect of a blacklist, for
+	 * details you can read pcie_aspm_sanity_check() and see how it adjusts
+	 * the device link capability.
+	 *
+	 * It may be possible in the future to implement some PCI API to allow
+	 * drivers to override blacklists for pre 1.1 PCIe but for now it is
+	 * best to accept that both L0s and L1 will be disabled completely for
+	 * distributions shipping with CONFIG_PCIEASPM rather than having this
+	 * issue present. Motivation for adding this new API will be to help
+	 * with power consumption for some of these devices.
+	 */
+	pci_disable_link_state(pdev, PCIE_LINK_STATE_L0S);
+
+	ret = pci_enable_device(pdev);
+	if (ret) {
+		dev_err(&pdev->dev, "can't enable device\n");
+		goto err;
+	}
+
+	/* XXX 32-bit addressing only */
+	ret = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
+	if (ret) {
+		dev_err(&pdev->dev, "32-bit DMA not available\n");
+		goto err_dis;
+	}
+
+	/*
+	 * Cache line size is used to size and align various
+	 * structures used to communicate with the hardware.
+	 */
+	pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &csz);
+	if (csz == 0) {
+		/*
+		 * Linux 2.4.18 (at least) writes the cache line size
+		 * register as a 16-bit wide register which is wrong.
+		 * We must have this setup properly for rx buffer
+		 * DMA to work so force a reasonable value here if it
+		 * comes up zero.
+		 */
+		csz = L1_CACHE_BYTES >> 2;
+		pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, csz);
+	}
+	/*
+	 * The default setting of latency timer yields poor results,
+	 * set it to the value used by other systems.  It may be worth
+	 * tweaking this setting more.
+	 */
+	pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0xa8);
+
+	/* Enable bus mastering */
+	pci_set_master(pdev);
+
+	/*
+	 * Disable the RETRY_TIMEOUT register (0x41) to keep
+	 * PCI Tx retries from interfering with C3 CPU state.
+	 */
+	pci_write_config_byte(pdev, 0x41, 0);
+
+	ret = pci_request_region(pdev, 0, "ath5k");
+	if (ret) {
+		dev_err(&pdev->dev, "cannot reserve PCI memory region\n");
+		goto err_dis;
+	}
+
+	mem = pci_iomap(pdev, 0, 0);
+	if (!mem) {
+		dev_err(&pdev->dev, "cannot remap PCI memory region\n");
+		ret = -EIO;
+		goto err_reg;
+	}
+
+	/*
+	 * Allocate hw (mac80211 main struct)
+	 * and hw->priv (driver private data)
+	 */
+	hw = ieee80211_alloc_hw(sizeof(*ah), &ath5k_hw_ops);
+	if (hw == NULL) {
+		dev_err(&pdev->dev, "cannot allocate ieee80211_hw\n");
+		ret = -ENOMEM;
+		goto err_map;
+	}
+
+	dev_info(&pdev->dev, "registered as '%s'\n", wiphy_name(hw->wiphy));
+
+	ah = hw->priv;
+	ah->hw = hw;
+	ah->pdev = pdev;
+	ah->dev = &pdev->dev;
+	ah->irq = pdev->irq;
+	ah->devid = id->device;
+	ah->iobase = mem; /* So we can unmap it on detach */
+
+	/* Initialize */
+	ret = ath5k_init_ah(ah, &ath_pci_bus_ops);
+	if (ret)
+		goto err_free;
+
+	/* Set private data */
+	pci_set_drvdata(pdev, hw);
+
+	return 0;
+err_free:
+	ieee80211_free_hw(hw);
+err_map:
+	pci_iounmap(pdev, mem);
+err_reg:
+	pci_release_region(pdev, 0);
+err_dis:
+	pci_disable_device(pdev);
+err:
+	return ret;
+}
+
+static void
+ath5k_pci_remove(struct pci_dev *pdev)
+{
+	struct ieee80211_hw *hw = pci_get_drvdata(pdev);
+	struct ath5k_hw *ah = hw->priv;
+
+	ath5k_deinit_ah(ah);
+	pci_iounmap(pdev, ah->iobase);
+	pci_release_region(pdev, 0);
+	pci_disable_device(pdev);
+	ieee80211_free_hw(hw);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int ath5k_pci_suspend(struct device *dev)
+{
+	struct ieee80211_hw *hw = dev_get_drvdata(dev);
+	struct ath5k_hw *ah = hw->priv;
+
+	ath5k_led_off(ah);
+	return 0;
+}
+
+static int ath5k_pci_resume(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct ieee80211_hw *hw = pci_get_drvdata(pdev);
+	struct ath5k_hw *ah = hw->priv;
+
+	/*
+	 * Suspend/Resume resets the PCI configuration space, so we have to
+	 * re-disable the RETRY_TIMEOUT register (0x41) to keep
+	 * PCI Tx retries from interfering with C3 CPU state
+	 */
+	pci_write_config_byte(pdev, 0x41, 0);
+
+	ath5k_led_enable(ah);
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(ath5k_pm_ops, ath5k_pci_suspend, ath5k_pci_resume);
+#define ATH5K_PM_OPS	(&ath5k_pm_ops)
+#else
+#define ATH5K_PM_OPS	NULL
+#endif /* CONFIG_PM_SLEEP */
+
+static struct pci_driver ath5k_pci_driver = {
+	.name		= KBUILD_MODNAME,
+	.id_table	= ath5k_pci_id_table,
+	.probe		= ath5k_pci_probe,
+	.remove		= ath5k_pci_remove,
+	.driver.pm	= ATH5K_PM_OPS,
+};
+
+module_pci_driver(ath5k_pci_driver);

linux-7.2.3/drivers/net/wireless/ath/ath5k/qcu.c

@@ -0,0 +1,729 @@
+/*
+ * Copyright (c) 2004-2008 Reyk Floeter <reyk@openbsd.org>
+ * Copyright (c) 2006-2008 Nick Kossifidis <mickflemm@gmail.com>
+ *
+ * Permission to use, copy, modify, and distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+/********************************************\
+Queue Control Unit, DCF Control Unit Functions
+\********************************************/
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include "ath5k.h"
+#include "reg.h"
+#include "debug.h"
+#include <linux/log2.h>
+
+/**
+ * DOC: Queue Control Unit (QCU)/DCF Control Unit (DCU) functions
+ *
+ * Here we setup parameters for the 12 available TX queues. Note that
+ * on the various registers we can usually only map the first 10 of them so
+ * basically we have 10 queues to play with. Each queue has a matching
+ * QCU that controls when the queue will get triggered and multiple QCUs
+ * can be mapped to a single DCU that controls the various DFS parameters
+ * for the various queues. In our setup we have a 1:1 mapping between QCUs
+ * and DCUs allowing us to have different DFS settings for each queue.
+ *
+ * When a frame goes into a TX queue, QCU decides when it'll trigger a
+ * transmission based on various criteria (such as how many data we have inside
+ * it's buffer or -if it's a beacon queue- if it's time to fire up the queue
+ * based on TSF etc), DCU adds backoff, IFSes etc and then a scheduler
+ * (arbitrator) decides the priority of each QCU based on it's configuration
+ * (e.g. beacons are always transmitted when they leave DCU bypassing all other
+ * frames from other queues waiting to be transmitted). After a frame leaves
+ * the DCU it goes to PCU for further processing and then to PHY for
+ * the actual transmission.
+ */
+
+
+/******************\
+* Helper functions *
+\******************/
+
+/**
+ * ath5k_hw_num_tx_pending() - Get number of pending frames for a  given queue
+ * @ah: The &struct ath5k_hw
+ * @queue: One of enum ath5k_tx_queue_id
+ */
+u32
+ath5k_hw_num_tx_pending(struct ath5k_hw *ah, unsigned int queue)
+{
+	u32 pending;
+	AR5K_ASSERT_ENTRY(queue, ah->ah_capabilities.cap_queues.q_tx_num);
+
+	/* Return if queue is declared inactive */
+	if (ah->ah_txq[queue].tqi_type == AR5K_TX_QUEUE_INACTIVE)
+		return false;
+
+	/* XXX: How about AR5K_CFG_TXCNT ? */
+	if (ah->ah_version == AR5K_AR5210)
+		return false;
+
+	pending = ath5k_hw_reg_read(ah, AR5K_QUEUE_STATUS(queue));
+	pending &= AR5K_QCU_STS_FRMPENDCNT;
+
+	/* It's possible to have no frames pending even if TXE
+	 * is set. To indicate that q has not stopped return
+	 * true */
+	if (!pending && AR5K_REG_READ_Q(ah, AR5K_QCU_TXE, queue))
+		return true;
+
+	return pending;
+}
+
+/**
+ * ath5k_hw_release_tx_queue() - Set a transmit queue inactive
+ * @ah: The &struct ath5k_hw
+ * @queue: One of enum ath5k_tx_queue_id
+ */
+void
+ath5k_hw_release_tx_queue(struct ath5k_hw *ah, unsigned int queue)
+{
+	if (WARN_ON(queue >= ah->ah_capabilities.cap_queues.q_tx_num))
+		return;
+
+	/* This queue will be skipped in further operations */
+	ah->ah_txq[queue].tqi_type = AR5K_TX_QUEUE_INACTIVE;
+	/*For SIMR setup*/
+	AR5K_Q_DISABLE_BITS(ah->ah_txq_status, queue);
+}
+
+/**
+ * ath5k_cw_validate() - Make sure the given cw is valid
+ * @cw_req: The contention window value to check
+ *
+ * Make sure cw is a power of 2 minus 1 and smaller than 1024
+ */
+static u16
+ath5k_cw_validate(u16 cw_req)
+{
+	cw_req = min(cw_req, (u16)1023);
+
+	/* Check if cw_req + 1 a power of 2 */
+	if (is_power_of_2(cw_req + 1))
+		return cw_req;
+
+	/* Check if cw_req is a power of 2 */
+	if (is_power_of_2(cw_req))
+		return cw_req - 1;
+
+	/* If none of the above is correct
+	 * find the closest power of 2 */
+	cw_req = (u16) roundup_pow_of_two(cw_req) - 1;
+
+	return cw_req;
+}
+
+/**
+ * ath5k_hw_get_tx_queueprops() - Get properties for a transmit queue
+ * @ah: The &struct ath5k_hw
+ * @queue: One of enum ath5k_tx_queue_id
+ * @queue_info: The &struct ath5k_txq_info to fill
+ */
+int
+ath5k_hw_get_tx_queueprops(struct ath5k_hw *ah, int queue,
+		struct ath5k_txq_info *queue_info)
+{
+	memcpy(queue_info, &ah->ah_txq[queue], sizeof(struct ath5k_txq_info));
+	return 0;
+}
+
+/**
+ * ath5k_hw_set_tx_queueprops() - Set properties for a transmit queue
+ * @ah: The &struct ath5k_hw
+ * @queue: One of enum ath5k_tx_queue_id
+ * @qinfo: The &struct ath5k_txq_info to use
+ *
+ * Returns 0 on success or -EIO if queue is inactive
+ */
+int
+ath5k_hw_set_tx_queueprops(struct ath5k_hw *ah, int queue,
+				const struct ath5k_txq_info *qinfo)
+{
+	struct ath5k_txq_info *qi;
+
+	AR5K_ASSERT_ENTRY(queue, ah->ah_capabilities.cap_queues.q_tx_num);
+
+	qi = &ah->ah_txq[queue];
+
+	if (qi->tqi_type == AR5K_TX_QUEUE_INACTIVE)
+		return -EIO;
+
+	/* copy and validate values */
+	qi->tqi_type = qinfo->tqi_type;
+	qi->tqi_subtype = qinfo->tqi_subtype;
+	qi->tqi_flags = qinfo->tqi_flags;
+	/*
+	 * According to the docs: Although the AIFS field is 8 bit wide,
+	 * the maximum supported value is 0xFC. Setting it higher than that
+	 * will cause the DCU to hang.
+	 */
+	qi->tqi_aifs = min(qinfo->tqi_aifs, (u8)0xFC);
+	qi->tqi_cw_min = ath5k_cw_validate(qinfo->tqi_cw_min);
+	qi->tqi_cw_max = ath5k_cw_validate(qinfo->tqi_cw_max);
+	qi->tqi_cbr_period = qinfo->tqi_cbr_period;
+	qi->tqi_cbr_overflow_limit = qinfo->tqi_cbr_overflow_limit;
+	qi->tqi_burst_time = qinfo->tqi_burst_time;
+	qi->tqi_ready_time = qinfo->tqi_ready_time;
+
+	/*XXX: Is this supported on 5210 ?*/
+	/*XXX: Is this correct for AR5K_WME_AC_VI,VO ???*/
+	if ((qinfo->tqi_type == AR5K_TX_QUEUE_DATA &&
+		((qinfo->tqi_subtype == AR5K_WME_AC_VI) ||
+		 (qinfo->tqi_subtype == AR5K_WME_AC_VO))) ||
+	     qinfo->tqi_type == AR5K_TX_QUEUE_UAPSD)
+		qi->tqi_flags |= AR5K_TXQ_FLAG_POST_FR_BKOFF_DIS;
+
+	return 0;
+}
+
+/**
+ * ath5k_hw_setup_tx_queue() - Initialize a transmit queue
+ * @ah: The &struct ath5k_hw
+ * @queue_type: One of enum ath5k_tx_queue
+ * @queue_info: The &struct ath5k_txq_info to use
+ *
+ * Returns 0 on success, -EINVAL on invalid arguments
+ */
+int
+ath5k_hw_setup_tx_queue(struct ath5k_hw *ah, enum ath5k_tx_queue queue_type,
+		struct ath5k_txq_info *queue_info)
+{
+	unsigned int queue;
+	int ret;
+
+	/*
+	 * Get queue by type
+	 */
+	/* 5210 only has 2 queues */
+	if (ah->ah_capabilities.cap_queues.q_tx_num == 2) {
+		switch (queue_type) {
+		case AR5K_TX_QUEUE_DATA:
+			queue = AR5K_TX_QUEUE_ID_NOQCU_DATA;
+			break;
+		case AR5K_TX_QUEUE_BEACON:
+		case AR5K_TX_QUEUE_CAB:
+			queue = AR5K_TX_QUEUE_ID_NOQCU_BEACON;
+			break;
+		default:
+			return -EINVAL;
+		}
+	} else {
+		switch (queue_type) {
+		case AR5K_TX_QUEUE_DATA:
+			queue = queue_info->tqi_subtype;
+			break;
+		case AR5K_TX_QUEUE_UAPSD:
+			queue = AR5K_TX_QUEUE_ID_UAPSD;
+			break;
+		case AR5K_TX_QUEUE_BEACON:
+			queue = AR5K_TX_QUEUE_ID_BEACON;
+			break;
+		case AR5K_TX_QUEUE_CAB:
+			queue = AR5K_TX_QUEUE_ID_CAB;
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	/*
+	 * Setup internal queue structure
+	 */
+	memset(&ah->ah_txq[queue], 0, sizeof(struct ath5k_txq_info));
+	ah->ah_txq[queue].tqi_type = queue_type;
+
+	if (queue_info != NULL) {
+		queue_info->tqi_type = queue_type;
+		ret = ath5k_hw_set_tx_queueprops(ah, queue, queue_info);
+		if (ret)
+			return ret;
+	}
+
+	/*
+	 * We use ah_txq_status to hold a temp value for
+	 * the Secondary interrupt mask registers on 5211+
+	 * check out ath5k_hw_reset_tx_queue
+	 */
+	AR5K_Q_ENABLE_BITS(ah->ah_txq_status, queue);
+
+	return queue;
+}
+
+
+/*******************************\
+* Single QCU/DCU initialization *
+\*******************************/
+
+/**
+ * ath5k_hw_set_tx_retry_limits() - Set tx retry limits on DCU
+ * @ah: The &struct ath5k_hw
+ * @queue: One of enum ath5k_tx_queue_id
+ *
+ * This function is used when initializing a queue, to set
+ * retry limits based on ah->ah_retry_* and the chipset used.
+ */
+void
+ath5k_hw_set_tx_retry_limits(struct ath5k_hw *ah,
+				  unsigned int queue)
+{
+	/* Single data queue on AR5210 */
+	if (ah->ah_version == AR5K_AR5210) {
+		struct ath5k_txq_info *tq = &ah->ah_txq[queue];
+
+		if (queue > 0)
+			return;
+
+		ath5k_hw_reg_write(ah,
+			(tq->tqi_cw_min << AR5K_NODCU_RETRY_LMT_CW_MIN_S)
+			| AR5K_REG_SM(ah->ah_retry_long,
+				      AR5K_NODCU_RETRY_LMT_SLG_RETRY)
+			| AR5K_REG_SM(ah->ah_retry_short,
+				      AR5K_NODCU_RETRY_LMT_SSH_RETRY)
+			| AR5K_REG_SM(ah->ah_retry_long,
+				      AR5K_NODCU_RETRY_LMT_LG_RETRY)
+			| AR5K_REG_SM(ah->ah_retry_short,
+				      AR5K_NODCU_RETRY_LMT_SH_RETRY),
+			AR5K_NODCU_RETRY_LMT);
+	/* DCU on AR5211+ */
+	} else {
+		ath5k_hw_reg_write(ah,
+			AR5K_REG_SM(ah->ah_retry_long,
+				    AR5K_DCU_RETRY_LMT_RTS)
+			| AR5K_REG_SM(ah->ah_retry_long,
+				      AR5K_DCU_RETRY_LMT_STA_RTS)
+			| AR5K_REG_SM(max(ah->ah_retry_long, ah->ah_retry_short),
+				      AR5K_DCU_RETRY_LMT_STA_DATA),
+			AR5K_QUEUE_DFS_RETRY_LIMIT(queue));
+	}
+}
+
+/**
+ * ath5k_hw_reset_tx_queue() - Initialize a single hw queue
+ * @ah: The &struct ath5k_hw
+ * @queue: One of enum ath5k_tx_queue_id
+ *
+ * Set DCF properties for the given transmit queue on DCU
+ * and configures all queue-specific parameters.
+ */
+int
+ath5k_hw_reset_tx_queue(struct ath5k_hw *ah, unsigned int queue)
+{
+	struct ath5k_txq_info *tq = &ah->ah_txq[queue];
+
+	AR5K_ASSERT_ENTRY(queue, ah->ah_capabilities.cap_queues.q_tx_num);
+
+	/* Skip if queue inactive or if we are on AR5210
+	 * that doesn't have QCU/DCU */
+	if ((ah->ah_version == AR5K_AR5210) ||
+	(tq->tqi_type == AR5K_TX_QUEUE_INACTIVE))
+		return 0;
+
+	/*
+	 * Set contention window (cw_min/cw_max)
+	 * and arbitrated interframe space (aifs)...
+	 */
+	ath5k_hw_reg_write(ah,
+		AR5K_REG_SM(tq->tqi_cw_min, AR5K_DCU_LCL_IFS_CW_MIN) |
+		AR5K_REG_SM(tq->tqi_cw_max, AR5K_DCU_LCL_IFS_CW_MAX) |
+		AR5K_REG_SM(tq->tqi_aifs, AR5K_DCU_LCL_IFS_AIFS),
+		AR5K_QUEUE_DFS_LOCAL_IFS(queue));
+
+	/*
+	 * Set tx retry limits for this queue
+	 */
+	ath5k_hw_set_tx_retry_limits(ah, queue);
+
+
+	/*
+	 * Set misc registers
+	 */
+
+	/* Enable DCU to wait for next fragment from QCU */
+	AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_DFS_MISC(queue),
+				AR5K_DCU_MISC_FRAG_WAIT);
+
+	/* On Maui and Spirit use the global seqnum on DCU */
+	if (ah->ah_mac_version < AR5K_SREV_AR5211)
+		AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_DFS_MISC(queue),
+					AR5K_DCU_MISC_SEQNUM_CTL);
+
+	/* Constant bit rate period */
+	if (tq->tqi_cbr_period) {
+		ath5k_hw_reg_write(ah, AR5K_REG_SM(tq->tqi_cbr_period,
+					AR5K_QCU_CBRCFG_INTVAL) |
+					AR5K_REG_SM(tq->tqi_cbr_overflow_limit,
+					AR5K_QCU_CBRCFG_ORN_THRES),
+					AR5K_QUEUE_CBRCFG(queue));
+
+		AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_MISC(queue),
+					AR5K_QCU_MISC_FRSHED_CBR);
+
+		if (tq->tqi_cbr_overflow_limit)
+			AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_MISC(queue),
+					AR5K_QCU_MISC_CBR_THRES_ENABLE);
+	}
+
+	/* Ready time interval */
+	if (tq->tqi_ready_time && (tq->tqi_type != AR5K_TX_QUEUE_CAB))
+		ath5k_hw_reg_write(ah, AR5K_REG_SM(tq->tqi_ready_time,
+					AR5K_QCU_RDYTIMECFG_INTVAL) |
+					AR5K_QCU_RDYTIMECFG_ENABLE,
+					AR5K_QUEUE_RDYTIMECFG(queue));
+
+	if (tq->tqi_burst_time) {
+		ath5k_hw_reg_write(ah, AR5K_REG_SM(tq->tqi_burst_time,
+					AR5K_DCU_CHAN_TIME_DUR) |
+					AR5K_DCU_CHAN_TIME_ENABLE,
+					AR5K_QUEUE_DFS_CHANNEL_TIME(queue));
+
+		if (tq->tqi_flags & AR5K_TXQ_FLAG_RDYTIME_EXP_POLICY_ENABLE)
+			AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_MISC(queue),
+					AR5K_QCU_MISC_RDY_VEOL_POLICY);
+	}
+
+	/* Enable/disable Post frame backoff */
+	if (tq->tqi_flags & AR5K_TXQ_FLAG_BACKOFF_DISABLE)
+		ath5k_hw_reg_write(ah, AR5K_DCU_MISC_POST_FR_BKOFF_DIS,
+					AR5K_QUEUE_DFS_MISC(queue));
+
+	/* Enable/disable fragmentation burst backoff */
+	if (tq->tqi_flags & AR5K_TXQ_FLAG_FRAG_BURST_BACKOFF_ENABLE)
+		ath5k_hw_reg_write(ah, AR5K_DCU_MISC_BACKOFF_FRAG,
+					AR5K_QUEUE_DFS_MISC(queue));
+
+	/*
+	 * Set registers by queue type
+	 */
+	switch (tq->tqi_type) {
+	case AR5K_TX_QUEUE_BEACON:
+		AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_MISC(queue),
+				AR5K_QCU_MISC_FRSHED_DBA_GT |
+				AR5K_QCU_MISC_CBREXP_BCN_DIS |
+				AR5K_QCU_MISC_BCN_ENABLE);
+
+		AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_DFS_MISC(queue),
+				(AR5K_DCU_MISC_ARBLOCK_CTL_GLOBAL <<
+				AR5K_DCU_MISC_ARBLOCK_CTL_S) |
+				AR5K_DCU_MISC_ARBLOCK_IGNORE |
+				AR5K_DCU_MISC_POST_FR_BKOFF_DIS |
+				AR5K_DCU_MISC_BCN_ENABLE);
+		break;
+
+	case AR5K_TX_QUEUE_CAB:
+		/* XXX: use BCN_SENT_GT, if we can figure out how */
+		AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_MISC(queue),
+					AR5K_QCU_MISC_FRSHED_DBA_GT |
+					AR5K_QCU_MISC_CBREXP_DIS |
+					AR5K_QCU_MISC_CBREXP_BCN_DIS);
+
+		ath5k_hw_reg_write(ah, ((tq->tqi_ready_time -
+					(AR5K_TUNE_SW_BEACON_RESP -
+					AR5K_TUNE_DMA_BEACON_RESP) -
+				AR5K_TUNE_ADDITIONAL_SWBA_BACKOFF) * 1024) |
+					AR5K_QCU_RDYTIMECFG_ENABLE,
+					AR5K_QUEUE_RDYTIMECFG(queue));
+
+		AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_DFS_MISC(queue),
+					(AR5K_DCU_MISC_ARBLOCK_CTL_GLOBAL <<
+					AR5K_DCU_MISC_ARBLOCK_CTL_S));
+		break;
+
+	case AR5K_TX_QUEUE_UAPSD:
+		AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_MISC(queue),
+					AR5K_QCU_MISC_CBREXP_DIS);
+		break;
+
+	case AR5K_TX_QUEUE_DATA:
+	default:
+			break;
+	}
+
+	/* TODO: Handle frame compression */
+
+	/*
+	 * Enable interrupts for this tx queue
+	 * in the secondary interrupt mask registers
+	 */
+	if (tq->tqi_flags & AR5K_TXQ_FLAG_TXOKINT_ENABLE)
+		AR5K_Q_ENABLE_BITS(ah->ah_txq_imr_txok, queue);
+
+	if (tq->tqi_flags & AR5K_TXQ_FLAG_TXERRINT_ENABLE)
+		AR5K_Q_ENABLE_BITS(ah->ah_txq_imr_txerr, queue);
+
+	if (tq->tqi_flags & AR5K_TXQ_FLAG_TXURNINT_ENABLE)
+		AR5K_Q_ENABLE_BITS(ah->ah_txq_imr_txurn, queue);
+
+	if (tq->tqi_flags & AR5K_TXQ_FLAG_TXDESCINT_ENABLE)
+		AR5K_Q_ENABLE_BITS(ah->ah_txq_imr_txdesc, queue);
+
+	if (tq->tqi_flags & AR5K_TXQ_FLAG_TXEOLINT_ENABLE)
+		AR5K_Q_ENABLE_BITS(ah->ah_txq_imr_txeol, queue);
+
+	if (tq->tqi_flags & AR5K_TXQ_FLAG_CBRORNINT_ENABLE)
+		AR5K_Q_ENABLE_BITS(ah->ah_txq_imr_cbrorn, queue);
+
+	if (tq->tqi_flags & AR5K_TXQ_FLAG_CBRURNINT_ENABLE)
+		AR5K_Q_ENABLE_BITS(ah->ah_txq_imr_cbrurn, queue);
+
+	if (tq->tqi_flags & AR5K_TXQ_FLAG_QTRIGINT_ENABLE)
+		AR5K_Q_ENABLE_BITS(ah->ah_txq_imr_qtrig, queue);
+
+	if (tq->tqi_flags & AR5K_TXQ_FLAG_TXNOFRMINT_ENABLE)
+		AR5K_Q_ENABLE_BITS(ah->ah_txq_imr_nofrm, queue);
+
+	/* Update secondary interrupt mask registers */
+
+	/* Filter out inactive queues */
+	ah->ah_txq_imr_txok &= ah->ah_txq_status;
+	ah->ah_txq_imr_txerr &= ah->ah_txq_status;
+	ah->ah_txq_imr_txurn &= ah->ah_txq_status;
+	ah->ah_txq_imr_txdesc &= ah->ah_txq_status;
+	ah->ah_txq_imr_txeol &= ah->ah_txq_status;
+	ah->ah_txq_imr_cbrorn &= ah->ah_txq_status;
+	ah->ah_txq_imr_cbrurn &= ah->ah_txq_status;
+	ah->ah_txq_imr_qtrig &= ah->ah_txq_status;
+	ah->ah_txq_imr_nofrm &= ah->ah_txq_status;
+
+	ath5k_hw_reg_write(ah, AR5K_REG_SM(ah->ah_txq_imr_txok,
+					AR5K_SIMR0_QCU_TXOK) |
+					AR5K_REG_SM(ah->ah_txq_imr_txdesc,
+					AR5K_SIMR0_QCU_TXDESC),
+					AR5K_SIMR0);
+
+	ath5k_hw_reg_write(ah, AR5K_REG_SM(ah->ah_txq_imr_txerr,
+					AR5K_SIMR1_QCU_TXERR) |
+					AR5K_REG_SM(ah->ah_txq_imr_txeol,
+					AR5K_SIMR1_QCU_TXEOL),
+					AR5K_SIMR1);
+
+	/* Update SIMR2 but don't overwrite rest simr2 settings */
+	AR5K_REG_DISABLE_BITS(ah, AR5K_SIMR2, AR5K_SIMR2_QCU_TXURN);
+	AR5K_REG_ENABLE_BITS(ah, AR5K_SIMR2,
+				AR5K_REG_SM(ah->ah_txq_imr_txurn,
+				AR5K_SIMR2_QCU_TXURN));
+
+	ath5k_hw_reg_write(ah, AR5K_REG_SM(ah->ah_txq_imr_cbrorn,
+				AR5K_SIMR3_QCBRORN) |
+				AR5K_REG_SM(ah->ah_txq_imr_cbrurn,
+				AR5K_SIMR3_QCBRURN),
+				AR5K_SIMR3);
+
+	ath5k_hw_reg_write(ah, AR5K_REG_SM(ah->ah_txq_imr_qtrig,
+				AR5K_SIMR4_QTRIG), AR5K_SIMR4);
+
+	/* Set TXNOFRM_QCU for the queues with TXNOFRM enabled */
+	ath5k_hw_reg_write(ah, AR5K_REG_SM(ah->ah_txq_imr_nofrm,
+				AR5K_TXNOFRM_QCU), AR5K_TXNOFRM);
+
+	/* No queue has TXNOFRM enabled, disable the interrupt
+	 * by setting AR5K_TXNOFRM to zero */
+	if (ah->ah_txq_imr_nofrm == 0)
+		ath5k_hw_reg_write(ah, 0, AR5K_TXNOFRM);
+
+	/* Set QCU mask for this DCU to save power */
+	AR5K_REG_WRITE_Q(ah, AR5K_QUEUE_QCUMASK(queue), queue);
+
+	return 0;
+}
+
+
+/**************************\
+* Global QCU/DCU functions *
+\**************************/
+
+/**
+ * ath5k_hw_set_ifs_intervals()  - Set global inter-frame spaces on DCU
+ * @ah: The &struct ath5k_hw
+ * @slot_time: Slot time in us
+ *
+ * Sets the global IFS intervals on DCU (also works on AR5210) for
+ * the given slot time and the current bwmode.
+ */
+int ath5k_hw_set_ifs_intervals(struct ath5k_hw *ah, unsigned int slot_time)
+{
+	struct ieee80211_channel *channel = ah->ah_current_channel;
+	enum nl80211_band band;
+	struct ieee80211_supported_band *sband;
+	struct ieee80211_rate *rate;
+	u32 ack_tx_time, eifs, eifs_clock, sifs, sifs_clock;
+	u32 slot_time_clock = ath5k_hw_htoclock(ah, slot_time);
+	u32 rate_flags, i;
+
+	if (slot_time < 6 || slot_time_clock > AR5K_SLOT_TIME_MAX)
+		return -EINVAL;
+
+	sifs = ath5k_hw_get_default_sifs(ah);
+	sifs_clock = ath5k_hw_htoclock(ah, sifs - 2);
+
+	/* EIFS
+	 * Txtime of ack at lowest rate + SIFS + DIFS
+	 * (DIFS = SIFS + 2 * Slot time)
+	 *
+	 * Note: HAL has some predefined values for EIFS
+	 * Turbo:   (37 + 2 * 6)
+	 * Default: (74 + 2 * 9)
+	 * Half:    (149 + 2 * 13)
+	 * Quarter: (298 + 2 * 21)
+	 *
+	 * (74 + 2 * 6) for AR5210 default and turbo !
+	 *
+	 * According to the formula we have
+	 * ack_tx_time = 25 for turbo and
+	 * ack_tx_time = 42.5 * clock multiplier
+	 * for default/half/quarter.
+	 *
+	 * This can't be right, 42 is what we would get
+	 * from ath5k_hw_get_frame_dur_for_bwmode or
+	 * ieee80211_generic_frame_duration for zero frame
+	 * length and without SIFS !
+	 *
+	 * Also we have different lowest rate for 802.11a
+	 */
+	if (channel->band == NL80211_BAND_5GHZ)
+		band = NL80211_BAND_5GHZ;
+	else
+		band = NL80211_BAND_2GHZ;
+
+	switch (ah->ah_bwmode) {
+	case AR5K_BWMODE_5MHZ:
+		rate_flags = IEEE80211_RATE_SUPPORTS_5MHZ;
+		break;
+	case AR5K_BWMODE_10MHZ:
+		rate_flags = IEEE80211_RATE_SUPPORTS_10MHZ;
+		break;
+	default:
+		rate_flags = 0;
+		break;
+	}
+	sband = &ah->sbands[band];
+	rate = NULL;
+	for (i = 0; i < sband->n_bitrates; i++) {
+		if ((rate_flags & sband->bitrates[i].flags) != rate_flags)
+			continue;
+		rate = &sband->bitrates[i];
+		break;
+	}
+	if (WARN_ON(!rate))
+		return -EINVAL;
+
+	ack_tx_time = ath5k_hw_get_frame_duration(ah, band, 10, rate, false);
+
+	/* ack_tx_time includes an SIFS already */
+	eifs = ack_tx_time + sifs + 2 * slot_time;
+	eifs_clock = ath5k_hw_htoclock(ah, eifs);
+
+	/* Set IFS settings on AR5210 */
+	if (ah->ah_version == AR5K_AR5210) {
+		u32 pifs, pifs_clock, difs, difs_clock;
+
+		/* Set slot time */
+		ath5k_hw_reg_write(ah, slot_time_clock, AR5K_SLOT_TIME);
+
+		/* Set EIFS */
+		eifs_clock = AR5K_REG_SM(eifs_clock, AR5K_IFS1_EIFS);
+
+		/* PIFS = Slot time + SIFS */
+		pifs = slot_time + sifs;
+		pifs_clock = ath5k_hw_htoclock(ah, pifs);
+		pifs_clock = AR5K_REG_SM(pifs_clock, AR5K_IFS1_PIFS);
+
+		/* DIFS = SIFS + 2 * Slot time */
+		difs = sifs + 2 * slot_time;
+		difs_clock = ath5k_hw_htoclock(ah, difs);
+
+		/* Set SIFS/DIFS */
+		ath5k_hw_reg_write(ah, (difs_clock <<
+				AR5K_IFS0_DIFS_S) | sifs_clock,
+				AR5K_IFS0);
+
+		/* Set PIFS/EIFS and preserve AR5K_INIT_CARR_SENSE_EN */
+		ath5k_hw_reg_write(ah, pifs_clock | eifs_clock |
+				(AR5K_INIT_CARR_SENSE_EN << AR5K_IFS1_CS_EN_S),
+				AR5K_IFS1);
+
+		return 0;
+	}
+
+	/* Set IFS slot time */
+	ath5k_hw_reg_write(ah, slot_time_clock, AR5K_DCU_GBL_IFS_SLOT);
+
+	/* Set EIFS interval */
+	ath5k_hw_reg_write(ah, eifs_clock, AR5K_DCU_GBL_IFS_EIFS);
+
+	/* Set SIFS interval in usecs */
+	AR5K_REG_WRITE_BITS(ah, AR5K_DCU_GBL_IFS_MISC,
+				AR5K_DCU_GBL_IFS_MISC_SIFS_DUR_USEC,
+				sifs);
+
+	/* Set SIFS interval in clock cycles */
+	ath5k_hw_reg_write(ah, sifs_clock, AR5K_DCU_GBL_IFS_SIFS);
+
+	return 0;
+}
+
+
+/**
+ * ath5k_hw_init_queues() - Initialize tx queues
+ * @ah: The &struct ath5k_hw
+ *
+ * Initializes all tx queues based on information on
+ * ah->ah_txq* set by the driver
+ */
+int
+ath5k_hw_init_queues(struct ath5k_hw *ah)
+{
+	int i, ret;
+
+	/* TODO: HW Compression support for data queues */
+	/* TODO: Burst prefetch for data queues */
+
+	/*
+	 * Reset queues and start beacon timers at the end of the reset routine
+	 * This also sets QCU mask on each DCU for 1:1 qcu to dcu mapping
+	 * Note: If we want we can assign multiple qcus on one dcu.
+	 */
+	if (ah->ah_version != AR5K_AR5210)
+		for (i = 0; i < ah->ah_capabilities.cap_queues.q_tx_num; i++) {
+			ret = ath5k_hw_reset_tx_queue(ah, i);
+			if (ret) {
+				ATH5K_ERR(ah,
+					"failed to reset TX queue #%d\n", i);
+				return ret;
+			}
+		}
+	else
+		/* No QCU/DCU on AR5210, just set tx
+		 * retry limits. We set IFS parameters
+		 * on ath5k_hw_set_ifs_intervals */
+		ath5k_hw_set_tx_retry_limits(ah, 0);
+
+	/* Set the turbo flag when operating on 40MHz */
+	if (ah->ah_bwmode == AR5K_BWMODE_40MHZ)
+		AR5K_REG_ENABLE_BITS(ah, AR5K_DCU_GBL_IFS_MISC,
+				AR5K_DCU_GBL_IFS_MISC_TURBO_MODE);
+
+	/* If we didn't set IFS timings through
+	 * ath5k_hw_set_coverage_class make sure
+	 * we set them here */
+	if (!ah->ah_coverage_class) {
+		unsigned int slot_time = ath5k_hw_get_default_slottime(ah);
+		ath5k_hw_set_ifs_intervals(ah, slot_time);
+	}
+
+	return 0;
+}

linux-7.2.3/drivers/net/wireless/ath/ath5k/rfbuffer.h

@@ -0,0 +1,853 @@
+/*
+ * RF Buffer handling functions
+ *
+ * Copyright (c) 2009 Nick Kossifidis <mickflemm@gmail.com>
+ *
+ * Permission to use, copy, modify, and distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+
+/**
+ * DOC: RF Buffer registers
+ *
+ * There are some special registers on the RF chip
+ * that control various operation settings related mostly to
+ * the analog parts (channel, gain adjustment etc).
+ *
+ * We don't write on those registers directly but
+ * we send a data packet on the chip, using a special register,
+ * that holds all the settings we need. After we've sent the
+ * data packet, we write on another special register to notify hw
+ * to apply the settings. This is done so that control registers
+ * can be dynamically programmed during operation and the settings
+ * are applied faster on the hw.
+ *
+ * We call each data packet an "RF Bank" and all the data we write
+ * (all RF Banks) "RF Buffer". This file holds initial RF Buffer
+ * data for the different RF chips, and various info to match RF
+ * Buffer offsets with specific RF registers so that we can access
+ * them. We tweak these settings on rfregs_init function.
+ *
+ * Also check out reg.h and U.S. Patent 6677779 B1 (about buffer
+ * registers and control registers):
+ *
+ * https://www.google.com/patents?id=qNURAAAAEBAJ
+ */
+
+
+/**
+ * struct ath5k_ini_rfbuffer - Initial RF Buffer settings
+ * @rfb_bank: RF Bank number
+ * @rfb_ctrl_register: RF Buffer control register
+ * @rfb_mode_data: RF Buffer data for each mode
+ *
+ * Struct to hold default mode specific RF
+ * register values (RF Banks) for each chip.
+ */
+struct ath5k_ini_rfbuffer {
+	u8	rfb_bank;
+	u16	rfb_ctrl_register;
+	u32	rfb_mode_data[3];
+};
+
+/**
+ * struct ath5k_rfb_field - An RF Buffer field (register/value)
+ * @len: Field length
+ * @pos: Offset on the raw packet
+ * @col: Used for shifting
+ *
+ * Struct to hold RF Buffer field
+ * infos used to access certain RF
+ * analog registers
+ */
+struct ath5k_rfb_field {
+	u8	len;
+	u16	pos;
+	u8	col;
+};
+
+/**
+ * struct ath5k_rf_reg - RF analog register definition
+ * @bank: RF Buffer Bank number
+ * @index: Register's index on ath5k_rf_regx_idx
+ * @field: The &struct ath5k_rfb_field
+ *
+ * We use this struct to define the set of RF registers
+ * on each chip that we want to tweak. Some RF registers
+ * are common between different chip versions so this saves
+ * us space and complexity because we can refer to an rf
+ * register by it's index no matter what chip we work with
+ * as long as it has that register.
+ */
+struct ath5k_rf_reg {
+	u8			bank;
+	u8			index;
+	struct ath5k_rfb_field	field;
+};
+
+/**
+ * enum ath5k_rf_regs_idx - Map RF registers to indexes
+ *
+ * We do this to handle common bits and make our
+ * life easier by using an index for each register
+ * instead of a full rfb_field
+ */
+enum ath5k_rf_regs_idx {
+	/* BANK 2 */
+	AR5K_RF_TURBO = 0,
+	/* BANK 6 */
+	AR5K_RF_OB_2GHZ,
+	AR5K_RF_OB_5GHZ,
+	AR5K_RF_DB_2GHZ,
+	AR5K_RF_DB_5GHZ,
+	AR5K_RF_FIXED_BIAS_A,
+	AR5K_RF_FIXED_BIAS_B,
+	AR5K_RF_PWD_XPD,
+	AR5K_RF_XPD_SEL,
+	AR5K_RF_XPD_GAIN,
+	AR5K_RF_PD_GAIN_LO,
+	AR5K_RF_PD_GAIN_HI,
+	AR5K_RF_HIGH_VC_CP,
+	AR5K_RF_MID_VC_CP,
+	AR5K_RF_LOW_VC_CP,
+	AR5K_RF_PUSH_UP,
+	AR5K_RF_PAD2GND,
+	AR5K_RF_XB2_LVL,
+	AR5K_RF_XB5_LVL,
+	AR5K_RF_PWD_ICLOBUF_2G,
+	AR5K_RF_PWD_84,
+	AR5K_RF_PWD_90,
+	AR5K_RF_PWD_130,
+	AR5K_RF_PWD_131,
+	AR5K_RF_PWD_132,
+	AR5K_RF_PWD_136,
+	AR5K_RF_PWD_137,
+	AR5K_RF_PWD_138,
+	AR5K_RF_PWD_166,
+	AR5K_RF_PWD_167,
+	AR5K_RF_DERBY_CHAN_SEL_MODE,
+	/* BANK 7 */
+	AR5K_RF_GAIN_I,
+	AR5K_RF_PLO_SEL,
+	AR5K_RF_RFGAIN_SEL,
+	AR5K_RF_RFGAIN_STEP,
+	AR5K_RF_WAIT_S,
+	AR5K_RF_WAIT_I,
+	AR5K_RF_MAX_TIME,
+	AR5K_RF_MIXVGA_OVR,
+	AR5K_RF_MIXGAIN_OVR,
+	AR5K_RF_MIXGAIN_STEP,
+	AR5K_RF_PD_DELAY_A,
+	AR5K_RF_PD_DELAY_B,
+	AR5K_RF_PD_DELAY_XR,
+	AR5K_RF_PD_PERIOD_A,
+	AR5K_RF_PD_PERIOD_B,
+	AR5K_RF_PD_PERIOD_XR,
+};
+
+
+/*******************\
+* RF5111 (Sombrero) *
+\*******************/
+
+/* BANK 2				len  pos col */
+#define	AR5K_RF5111_RF_TURBO		{ 1, 3,   0 }
+
+/* BANK 6				len  pos col */
+#define	AR5K_RF5111_OB_2GHZ		{ 3, 119, 0 }
+#define	AR5K_RF5111_DB_2GHZ		{ 3, 122, 0 }
+
+#define	AR5K_RF5111_OB_5GHZ		{ 3, 104, 0 }
+#define	AR5K_RF5111_DB_5GHZ		{ 3, 107, 0 }
+
+#define	AR5K_RF5111_PWD_XPD		{ 1, 95,  0 }
+#define	AR5K_RF5111_XPD_GAIN		{ 4, 96,  0 }
+
+/* Access to PWD registers */
+#define AR5K_RF5111_PWD(_n)		{ 1, (135 - _n), 3 }
+
+/* BANK 7				len  pos col */
+#define	AR5K_RF5111_GAIN_I		{ 6, 29,  0 }
+#define	AR5K_RF5111_PLO_SEL		{ 1, 4,   0 }
+#define	AR5K_RF5111_RFGAIN_SEL		{ 1, 36,  0 }
+#define AR5K_RF5111_RFGAIN_STEP		{ 6, 37,  0 }
+/* Only on AR5212 BaseBand and up */
+#define	AR5K_RF5111_WAIT_S		{ 5, 19,  0 }
+#define	AR5K_RF5111_WAIT_I		{ 5, 24,  0 }
+#define	AR5K_RF5111_MAX_TIME		{ 2, 49,  0 }
+
+static const struct ath5k_rf_reg rf_regs_5111[] = {
+	{2, AR5K_RF_TURBO,		AR5K_RF5111_RF_TURBO},
+	{6, AR5K_RF_OB_2GHZ,		AR5K_RF5111_OB_2GHZ},
+	{6, AR5K_RF_DB_2GHZ,		AR5K_RF5111_DB_2GHZ},
+	{6, AR5K_RF_OB_5GHZ,		AR5K_RF5111_OB_5GHZ},
+	{6, AR5K_RF_DB_5GHZ,		AR5K_RF5111_DB_5GHZ},
+	{6, AR5K_RF_PWD_XPD,		AR5K_RF5111_PWD_XPD},
+	{6, AR5K_RF_XPD_GAIN,		AR5K_RF5111_XPD_GAIN},
+	{6, AR5K_RF_PWD_84,		AR5K_RF5111_PWD(84)},
+	{6, AR5K_RF_PWD_90,		AR5K_RF5111_PWD(90)},
+	{7, AR5K_RF_GAIN_I,		AR5K_RF5111_GAIN_I},
+	{7, AR5K_RF_PLO_SEL,		AR5K_RF5111_PLO_SEL},
+	{7, AR5K_RF_RFGAIN_SEL,		AR5K_RF5111_RFGAIN_SEL},
+	{7, AR5K_RF_RFGAIN_STEP,	AR5K_RF5111_RFGAIN_STEP},
+	{7, AR5K_RF_WAIT_S,		AR5K_RF5111_WAIT_S},
+	{7, AR5K_RF_WAIT_I,		AR5K_RF5111_WAIT_I},
+	{7, AR5K_RF_MAX_TIME,		AR5K_RF5111_MAX_TIME}
+};
+
+/* Default mode specific settings */
+static const struct ath5k_ini_rfbuffer rfb_5111[] = {
+	/* BANK / C.R.     A/XR         B           G      */
+	{ 0, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 0, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 0, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 0, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 0, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 0, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 0, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 0, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 0, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 0, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 0, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 0, 0x989c, { 0x00380000, 0x00380000, 0x00380000 } },
+	{ 0, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 0, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 0, 0x989c, { 0x00000000, 0x000000c0, 0x00000080 } },
+	{ 0, 0x989c, { 0x000400f9, 0x000400ff, 0x000400fd } },
+	{ 0, 0x98d4, { 0x00000000, 0x00000004, 0x00000004 } },
+	{ 1, 0x98d4, { 0x00000020, 0x00000020, 0x00000020 } },
+	{ 2, 0x98d4, { 0x00000010, 0x00000010, 0x00000010 } },
+	{ 3, 0x98d8, { 0x00601068, 0x00601068, 0x00601068 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x10000000, 0x10000000, 0x10000000 } },
+	{ 6, 0x989c, { 0x04000000, 0x04000000, 0x04000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x0a000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x003800c0, 0x023800c0, 0x003800c0 } },
+	{ 6, 0x989c, { 0x00020006, 0x00000006, 0x00020006 } },
+	{ 6, 0x989c, { 0x00000089, 0x00000089, 0x00000089 } },
+	{ 6, 0x989c, { 0x000000a0, 0x000000a0, 0x000000a0 } },
+	{ 6, 0x989c, { 0x00040007, 0x00040007, 0x00040007 } },
+	{ 6, 0x98d4, { 0x0000001a, 0x0000001a, 0x0000001a } },
+	{ 7, 0x989c, { 0x00000040, 0x00000040, 0x00000040 } },
+	{ 7, 0x989c, { 0x00000010, 0x00000010, 0x00000010 } },
+	{ 7, 0x989c, { 0x00000008, 0x00000008, 0x00000008 } },
+	{ 7, 0x989c, { 0x0000004f, 0x0000004f, 0x0000004f } },
+	{ 7, 0x989c, { 0x000000f1, 0x00000061, 0x000000f1 } },
+	{ 7, 0x989c, { 0x0000904f, 0x0000904c, 0x0000904f } },
+	{ 7, 0x989c, { 0x0000125a, 0x0000129a, 0x0000125a } },
+	{ 7, 0x98cc, { 0x0000000e, 0x0000000f, 0x0000000e } },
+};
+
+
+
+/***********************\
+* RF5112/RF2112 (Derby) *
+\***********************/
+
+/* BANK 2 (Common)			len  pos col */
+#define	AR5K_RF5112X_RF_TURBO		{ 1, 1,   2 }
+
+/* BANK 7 (Common)			len  pos col */
+#define	AR5K_RF5112X_GAIN_I		{ 6, 14,  0 }
+#define	AR5K_RF5112X_MIXVGA_OVR		{ 1, 36,  0 }
+#define	AR5K_RF5112X_MIXGAIN_OVR	{ 2, 37,  0 }
+#define AR5K_RF5112X_MIXGAIN_STEP	{ 4, 32,  0 }
+#define	AR5K_RF5112X_PD_DELAY_A		{ 4, 58,  0 }
+#define	AR5K_RF5112X_PD_DELAY_B		{ 4, 62,  0 }
+#define	AR5K_RF5112X_PD_DELAY_XR	{ 4, 66,  0 }
+#define	AR5K_RF5112X_PD_PERIOD_A	{ 4, 70,  0 }
+#define	AR5K_RF5112X_PD_PERIOD_B	{ 4, 74,  0 }
+#define	AR5K_RF5112X_PD_PERIOD_XR	{ 4, 78,  0 }
+
+/* RFX112 (Derby 1) */
+
+/* BANK 6				len  pos col */
+#define	AR5K_RF5112_OB_2GHZ		{ 3, 269, 0 }
+#define	AR5K_RF5112_DB_2GHZ		{ 3, 272, 0 }
+
+#define	AR5K_RF5112_OB_5GHZ		{ 3, 261, 0 }
+#define	AR5K_RF5112_DB_5GHZ		{ 3, 264, 0 }
+
+#define	AR5K_RF5112_FIXED_BIAS_A	{ 1, 260, 0 }
+#define	AR5K_RF5112_FIXED_BIAS_B	{ 1, 259, 0 }
+
+#define	AR5K_RF5112_XPD_SEL		{ 1, 284, 0 }
+#define	AR5K_RF5112_XPD_GAIN		{ 2, 252, 0 }
+
+/* Access to PWD registers */
+#define AR5K_RF5112_PWD(_n)		{ 1, (302 - _n), 3 }
+
+static const struct ath5k_rf_reg rf_regs_5112[] = {
+	{2, AR5K_RF_TURBO,		AR5K_RF5112X_RF_TURBO},
+	{6, AR5K_RF_OB_2GHZ,		AR5K_RF5112_OB_2GHZ},
+	{6, AR5K_RF_DB_2GHZ,		AR5K_RF5112_DB_2GHZ},
+	{6, AR5K_RF_OB_5GHZ,		AR5K_RF5112_OB_5GHZ},
+	{6, AR5K_RF_DB_5GHZ,		AR5K_RF5112_DB_5GHZ},
+	{6, AR5K_RF_FIXED_BIAS_A,	AR5K_RF5112_FIXED_BIAS_A},
+	{6, AR5K_RF_FIXED_BIAS_B,	AR5K_RF5112_FIXED_BIAS_B},
+	{6, AR5K_RF_XPD_SEL,		AR5K_RF5112_XPD_SEL},
+	{6, AR5K_RF_XPD_GAIN,		AR5K_RF5112_XPD_GAIN},
+	{6, AR5K_RF_PWD_130,		AR5K_RF5112_PWD(130)},
+	{6, AR5K_RF_PWD_131,		AR5K_RF5112_PWD(131)},
+	{6, AR5K_RF_PWD_132,		AR5K_RF5112_PWD(132)},
+	{6, AR5K_RF_PWD_136,		AR5K_RF5112_PWD(136)},
+	{6, AR5K_RF_PWD_137,		AR5K_RF5112_PWD(137)},
+	{6, AR5K_RF_PWD_138,		AR5K_RF5112_PWD(138)},
+	{7, AR5K_RF_GAIN_I,		AR5K_RF5112X_GAIN_I},
+	{7, AR5K_RF_MIXVGA_OVR,		AR5K_RF5112X_MIXVGA_OVR},
+	{7, AR5K_RF_MIXGAIN_OVR,	AR5K_RF5112X_MIXGAIN_OVR},
+	{7, AR5K_RF_MIXGAIN_STEP,	AR5K_RF5112X_MIXGAIN_STEP},
+	{7, AR5K_RF_PD_DELAY_A,		AR5K_RF5112X_PD_DELAY_A},
+	{7, AR5K_RF_PD_DELAY_B,		AR5K_RF5112X_PD_DELAY_B},
+	{7, AR5K_RF_PD_DELAY_XR,	AR5K_RF5112X_PD_DELAY_XR},
+	{7, AR5K_RF_PD_PERIOD_A,	AR5K_RF5112X_PD_PERIOD_A},
+	{7, AR5K_RF_PD_PERIOD_B,	AR5K_RF5112X_PD_PERIOD_B},
+	{7, AR5K_RF_PD_PERIOD_XR,	AR5K_RF5112X_PD_PERIOD_XR},
+};
+
+/* Default mode specific settings */
+static const struct ath5k_ini_rfbuffer rfb_5112[] = {
+	/* BANK / C.R.     A/XR         B           G      */
+	{ 1, 0x98d4, { 0x00000020, 0x00000020, 0x00000020 } },
+	{ 2, 0x98d0, { 0x03060408, 0x03060408, 0x03060408 } },
+	{ 3, 0x98dc, { 0x00a0c0c0, 0x00e0c0c0, 0x00e0c0c0 } },
+	{ 6, 0x989c, { 0x00a00000, 0x00a00000, 0x00a00000 } },
+	{ 6, 0x989c, { 0x000a0000, 0x000a0000, 0x000a0000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00660000, 0x00660000, 0x00660000 } },
+	{ 6, 0x989c, { 0x00db0000, 0x00db0000, 0x00db0000 } },
+	{ 6, 0x989c, { 0x00f10000, 0x00f10000, 0x00f10000 } },
+	{ 6, 0x989c, { 0x00120000, 0x00120000, 0x00120000 } },
+	{ 6, 0x989c, { 0x00120000, 0x00120000, 0x00120000 } },
+	{ 6, 0x989c, { 0x00730000, 0x00730000, 0x00730000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x000c0000, 0x000c0000, 0x000c0000 } },
+	{ 6, 0x989c, { 0x00ff0000, 0x00ff0000, 0x00ff0000 } },
+	{ 6, 0x989c, { 0x00ff0000, 0x00ff0000, 0x00ff0000 } },
+	{ 6, 0x989c, { 0x008b0000, 0x008b0000, 0x008b0000 } },
+	{ 6, 0x989c, { 0x00600000, 0x00600000, 0x00600000 } },
+	{ 6, 0x989c, { 0x000c0000, 0x000c0000, 0x000c0000 } },
+	{ 6, 0x989c, { 0x00840000, 0x00840000, 0x00840000 } },
+	{ 6, 0x989c, { 0x00640000, 0x00640000, 0x00640000 } },
+	{ 6, 0x989c, { 0x00200000, 0x00200000, 0x00200000 } },
+	{ 6, 0x989c, { 0x00240000, 0x00240000, 0x00240000 } },
+	{ 6, 0x989c, { 0x00250000, 0x00250000, 0x00250000 } },
+	{ 6, 0x989c, { 0x00110000, 0x00110000, 0x00110000 } },
+	{ 6, 0x989c, { 0x00110000, 0x00110000, 0x00110000 } },
+	{ 6, 0x989c, { 0x00510000, 0x00510000, 0x00510000 } },
+	{ 6, 0x989c, { 0x1c040000, 0x1c040000, 0x1c040000 } },
+	{ 6, 0x989c, { 0x000a0000, 0x000a0000, 0x000a0000 } },
+	{ 6, 0x989c, { 0x00a10000, 0x00a10000, 0x00a10000 } },
+	{ 6, 0x989c, { 0x00400000, 0x00400000, 0x00400000 } },
+	{ 6, 0x989c, { 0x03090000, 0x03090000, 0x03090000 } },
+	{ 6, 0x989c, { 0x06000000, 0x06000000, 0x06000000 } },
+	{ 6, 0x989c, { 0x000000b0, 0x000000a8, 0x000000a8 } },
+	{ 6, 0x989c, { 0x0000002e, 0x0000002e, 0x0000002e } },
+	{ 6, 0x989c, { 0x006c4a41, 0x006c4af1, 0x006c4a61 } },
+	{ 6, 0x989c, { 0x0050892a, 0x0050892b, 0x0050892b } },
+	{ 6, 0x989c, { 0x00842400, 0x00842400, 0x00842400 } },
+	{ 6, 0x989c, { 0x00c69200, 0x00c69200, 0x00c69200 } },
+	{ 6, 0x98d0, { 0x0002000c, 0x0002000c, 0x0002000c } },
+	{ 7, 0x989c, { 0x00000094, 0x00000094, 0x00000094 } },
+	{ 7, 0x989c, { 0x00000091, 0x00000091, 0x00000091 } },
+	{ 7, 0x989c, { 0x0000000a, 0x00000012, 0x00000012 } },
+	{ 7, 0x989c, { 0x00000080, 0x00000080, 0x00000080 } },
+	{ 7, 0x989c, { 0x000000c1, 0x000000c1, 0x000000c1 } },
+	{ 7, 0x989c, { 0x00000060, 0x00000060, 0x00000060 } },
+	{ 7, 0x989c, { 0x000000f0, 0x000000f0, 0x000000f0 } },
+	{ 7, 0x989c, { 0x00000022, 0x00000022, 0x00000022 } },
+	{ 7, 0x989c, { 0x00000092, 0x00000092, 0x00000092 } },
+	{ 7, 0x989c, { 0x000000d4, 0x000000d4, 0x000000d4 } },
+	{ 7, 0x989c, { 0x000014cc, 0x000014cc, 0x000014cc } },
+	{ 7, 0x989c, { 0x0000048c, 0x0000048c, 0x0000048c } },
+	{ 7, 0x98c4, { 0x00000003, 0x00000003, 0x00000003 } },
+};
+
+/* RFX112A (Derby 2) */
+
+/* BANK 6				len  pos col */
+#define	AR5K_RF5112A_OB_2GHZ		{ 3, 287, 0 }
+#define	AR5K_RF5112A_DB_2GHZ		{ 3, 290, 0 }
+
+#define	AR5K_RF5112A_OB_5GHZ		{ 3, 279, 0 }
+#define	AR5K_RF5112A_DB_5GHZ		{ 3, 282, 0 }
+
+#define	AR5K_RF5112A_FIXED_BIAS_A	{ 1, 278, 0 }
+#define	AR5K_RF5112A_FIXED_BIAS_B	{ 1, 277, 0 }
+
+#define	AR5K_RF5112A_XPD_SEL		{ 1, 302, 0 }
+#define	AR5K_RF5112A_PDGAINLO		{ 2, 270, 0 }
+#define	AR5K_RF5112A_PDGAINHI		{ 2, 257, 0 }
+
+/* Access to PWD registers */
+#define AR5K_RF5112A_PWD(_n)		{ 1, (306 - _n), 3 }
+
+/* Voltage regulators */
+#define	AR5K_RF5112A_HIGH_VC_CP		{ 2, 90,  2 }
+#define	AR5K_RF5112A_MID_VC_CP		{ 2, 92,  2 }
+#define	AR5K_RF5112A_LOW_VC_CP		{ 2, 94,  2 }
+#define	AR5K_RF5112A_PUSH_UP		{ 1, 254,  2 }
+
+/* Power consumption */
+#define	AR5K_RF5112A_PAD2GND		{ 1, 281, 1 }
+#define	AR5K_RF5112A_XB2_LVL		{ 2, 1,	  3 }
+#define	AR5K_RF5112A_XB5_LVL		{ 2, 3,	  3 }
+
+static const struct ath5k_rf_reg rf_regs_5112a[] = {
+	{2, AR5K_RF_TURBO,		AR5K_RF5112X_RF_TURBO},
+	{6, AR5K_RF_OB_2GHZ,		AR5K_RF5112A_OB_2GHZ},
+	{6, AR5K_RF_DB_2GHZ,		AR5K_RF5112A_DB_2GHZ},
+	{6, AR5K_RF_OB_5GHZ,		AR5K_RF5112A_OB_5GHZ},
+	{6, AR5K_RF_DB_5GHZ,		AR5K_RF5112A_DB_5GHZ},
+	{6, AR5K_RF_FIXED_BIAS_A,	AR5K_RF5112A_FIXED_BIAS_A},
+	{6, AR5K_RF_FIXED_BIAS_B,	AR5K_RF5112A_FIXED_BIAS_B},
+	{6, AR5K_RF_XPD_SEL,		AR5K_RF5112A_XPD_SEL},
+	{6, AR5K_RF_PD_GAIN_LO,		AR5K_RF5112A_PDGAINLO},
+	{6, AR5K_RF_PD_GAIN_HI,		AR5K_RF5112A_PDGAINHI},
+	{6, AR5K_RF_PWD_130,		AR5K_RF5112A_PWD(130)},
+	{6, AR5K_RF_PWD_131,		AR5K_RF5112A_PWD(131)},
+	{6, AR5K_RF_PWD_132,		AR5K_RF5112A_PWD(132)},
+	{6, AR5K_RF_PWD_136,		AR5K_RF5112A_PWD(136)},
+	{6, AR5K_RF_PWD_137,		AR5K_RF5112A_PWD(137)},
+	{6, AR5K_RF_PWD_138,		AR5K_RF5112A_PWD(138)},
+	{6, AR5K_RF_PWD_166,		AR5K_RF5112A_PWD(166)},
+	{6, AR5K_RF_PWD_167,		AR5K_RF5112A_PWD(167)},
+	{6, AR5K_RF_HIGH_VC_CP,		AR5K_RF5112A_HIGH_VC_CP},
+	{6, AR5K_RF_MID_VC_CP,		AR5K_RF5112A_MID_VC_CP},
+	{6, AR5K_RF_LOW_VC_CP,		AR5K_RF5112A_LOW_VC_CP},
+	{6, AR5K_RF_PUSH_UP,		AR5K_RF5112A_PUSH_UP},
+	{6, AR5K_RF_PAD2GND,		AR5K_RF5112A_PAD2GND},
+	{6, AR5K_RF_XB2_LVL,		AR5K_RF5112A_XB2_LVL},
+	{6, AR5K_RF_XB5_LVL,		AR5K_RF5112A_XB5_LVL},
+	{7, AR5K_RF_GAIN_I,		AR5K_RF5112X_GAIN_I},
+	{7, AR5K_RF_MIXVGA_OVR,		AR5K_RF5112X_MIXVGA_OVR},
+	{7, AR5K_RF_MIXGAIN_OVR,	AR5K_RF5112X_MIXGAIN_OVR},
+	{7, AR5K_RF_MIXGAIN_STEP,	AR5K_RF5112X_MIXGAIN_STEP},
+	{7, AR5K_RF_PD_DELAY_A,		AR5K_RF5112X_PD_DELAY_A},
+	{7, AR5K_RF_PD_DELAY_B,		AR5K_RF5112X_PD_DELAY_B},
+	{7, AR5K_RF_PD_DELAY_XR,	AR5K_RF5112X_PD_DELAY_XR},
+	{7, AR5K_RF_PD_PERIOD_A,	AR5K_RF5112X_PD_PERIOD_A},
+	{7, AR5K_RF_PD_PERIOD_B,	AR5K_RF5112X_PD_PERIOD_B},
+	{7, AR5K_RF_PD_PERIOD_XR,	AR5K_RF5112X_PD_PERIOD_XR},
+};
+
+/* Default mode specific settings */
+static const struct ath5k_ini_rfbuffer rfb_5112a[] = {
+	/* BANK / C.R.     A/XR         B           G      */
+	{ 1, 0x98d4, { 0x00000020, 0x00000020, 0x00000020 } },
+	{ 2, 0x98d0, { 0x03060408, 0x03060408, 0x03060408 } },
+	{ 3, 0x98dc, { 0x00a020c0, 0x00e020c0, 0x00e020c0 } },
+	{ 6, 0x989c, { 0x0f000000, 0x0f000000, 0x0f000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00800000, 0x00800000, 0x00800000 } },
+	{ 6, 0x989c, { 0x002a0000, 0x002a0000, 0x002a0000 } },
+	{ 6, 0x989c, { 0x00010000, 0x00010000, 0x00010000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00180000, 0x00180000, 0x00180000 } },
+	{ 6, 0x989c, { 0x00600000, 0x006e0000, 0x006e0000 } },
+	{ 6, 0x989c, { 0x00c70000, 0x00c70000, 0x00c70000 } },
+	{ 6, 0x989c, { 0x004b0000, 0x004b0000, 0x004b0000 } },
+	{ 6, 0x989c, { 0x04480000, 0x04480000, 0x04480000 } },
+	{ 6, 0x989c, { 0x004c0000, 0x004c0000, 0x004c0000 } },
+	{ 6, 0x989c, { 0x00e40000, 0x00e40000, 0x00e40000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00fc0000, 0x00fc0000, 0x00fc0000 } },
+	{ 6, 0x989c, { 0x00ff0000, 0x00ff0000, 0x00ff0000 } },
+	{ 6, 0x989c, { 0x043f0000, 0x043f0000, 0x043f0000 } },
+	{ 6, 0x989c, { 0x000c0000, 0x000c0000, 0x000c0000 } },
+	{ 6, 0x989c, { 0x02190000, 0x02190000, 0x02190000 } },
+	{ 6, 0x989c, { 0x00240000, 0x00240000, 0x00240000 } },
+	{ 6, 0x989c, { 0x00b40000, 0x00b40000, 0x00b40000 } },
+	{ 6, 0x989c, { 0x00990000, 0x00990000, 0x00990000 } },
+	{ 6, 0x989c, { 0x00500000, 0x00500000, 0x00500000 } },
+	{ 6, 0x989c, { 0x002a0000, 0x002a0000, 0x002a0000 } },
+	{ 6, 0x989c, { 0x00120000, 0x00120000, 0x00120000 } },
+	{ 6, 0x989c, { 0xc0320000, 0xc0320000, 0xc0320000 } },
+	{ 6, 0x989c, { 0x01740000, 0x01740000, 0x01740000 } },
+	{ 6, 0x989c, { 0x00110000, 0x00110000, 0x00110000 } },
+	{ 6, 0x989c, { 0x86280000, 0x86280000, 0x86280000 } },
+	{ 6, 0x989c, { 0x31840000, 0x31840000, 0x31840000 } },
+	{ 6, 0x989c, { 0x00f20080, 0x00f20080, 0x00f20080 } },
+	{ 6, 0x989c, { 0x00270019, 0x00270019, 0x00270019 } },
+	{ 6, 0x989c, { 0x00000003, 0x00000003, 0x00000003 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x000000b2, 0x000000b2, 0x000000b2 } },
+	{ 6, 0x989c, { 0x00b02084, 0x00b02084, 0x00b02084 } },
+	{ 6, 0x989c, { 0x004125a4, 0x004125a4, 0x004125a4 } },
+	{ 6, 0x989c, { 0x00119220, 0x00119220, 0x00119220 } },
+	{ 6, 0x989c, { 0x001a4800, 0x001a4800, 0x001a4800 } },
+	{ 6, 0x98d8, { 0x000b0230, 0x000b0230, 0x000b0230 } },
+	{ 7, 0x989c, { 0x00000094, 0x00000094, 0x00000094 } },
+	{ 7, 0x989c, { 0x00000091, 0x00000091, 0x00000091 } },
+	{ 7, 0x989c, { 0x00000012, 0x00000012, 0x00000012 } },
+	{ 7, 0x989c, { 0x00000080, 0x00000080, 0x00000080 } },
+	{ 7, 0x989c, { 0x000000d9, 0x000000d9, 0x000000d9 } },
+	{ 7, 0x989c, { 0x00000060, 0x00000060, 0x00000060 } },
+	{ 7, 0x989c, { 0x000000f0, 0x000000f0, 0x000000f0 } },
+	{ 7, 0x989c, { 0x000000a2, 0x000000a2, 0x000000a2 } },
+	{ 7, 0x989c, { 0x00000052, 0x00000052, 0x00000052 } },
+	{ 7, 0x989c, { 0x000000d4, 0x000000d4, 0x000000d4 } },
+	{ 7, 0x989c, { 0x000014cc, 0x000014cc, 0x000014cc } },
+	{ 7, 0x989c, { 0x0000048c, 0x0000048c, 0x0000048c } },
+	{ 7, 0x98c4, { 0x00000003, 0x00000003, 0x00000003 } },
+};
+
+
+
+/******************\
+* RF2413 (Griffin) *
+\******************/
+
+/* BANK 2				len  pos col */
+#define AR5K_RF2413_RF_TURBO		{ 1, 1,   2 }
+
+/* BANK 6				len  pos col */
+#define	AR5K_RF2413_OB_2GHZ		{ 3, 168, 0 }
+#define	AR5K_RF2413_DB_2GHZ		{ 3, 165, 0 }
+
+static const struct ath5k_rf_reg rf_regs_2413[] = {
+	{2, AR5K_RF_TURBO,		AR5K_RF2413_RF_TURBO},
+	{6, AR5K_RF_OB_2GHZ,		AR5K_RF2413_OB_2GHZ},
+	{6, AR5K_RF_DB_2GHZ,		AR5K_RF2413_DB_2GHZ},
+};
+
+/* Default mode specific settings
+ * XXX: a/aTurbo ???
+ */
+static const struct ath5k_ini_rfbuffer rfb_2413[] = {
+	/* BANK / C.R.     A/XR         B           G      */
+	{ 1, 0x98d4, { 0x00000020, 0x00000020, 0x00000020 } },
+	{ 2, 0x98d0, { 0x02001408, 0x02001408, 0x02001408 } },
+	{ 3, 0x98dc, { 0x00a020c0, 0x00e020c0, 0x00e020c0 } },
+	{ 6, 0x989c, { 0xf0000000, 0xf0000000, 0xf0000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x03000000, 0x03000000, 0x03000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x40400000, 0x40400000, 0x40400000 } },
+	{ 6, 0x989c, { 0x65050000, 0x65050000, 0x65050000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00420000, 0x00420000, 0x00420000 } },
+	{ 6, 0x989c, { 0x00b50000, 0x00b50000, 0x00b50000 } },
+	{ 6, 0x989c, { 0x00030000, 0x00030000, 0x00030000 } },
+	{ 6, 0x989c, { 0x00f70000, 0x00f70000, 0x00f70000 } },
+	{ 6, 0x989c, { 0x009d0000, 0x009d0000, 0x009d0000 } },
+	{ 6, 0x989c, { 0x00220000, 0x00220000, 0x00220000 } },
+	{ 6, 0x989c, { 0x04220000, 0x04220000, 0x04220000 } },
+	{ 6, 0x989c, { 0x00230018, 0x00230018, 0x00230018 } },
+	{ 6, 0x989c, { 0x00280000, 0x00280060, 0x00280060 } },
+	{ 6, 0x989c, { 0x005000c0, 0x005000c3, 0x005000c3 } },
+	{ 6, 0x989c, { 0x0004007f, 0x0004007f, 0x0004007f } },
+	{ 6, 0x989c, { 0x00000458, 0x00000458, 0x00000458 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x0000c000, 0x0000c000, 0x0000c000 } },
+	{ 6, 0x98d8, { 0x00400230, 0x00400230, 0x00400230 } },
+	{ 7, 0x989c, { 0x00006400, 0x00006400, 0x00006400 } },
+	{ 7, 0x989c, { 0x00000800, 0x00000800, 0x00000800 } },
+	{ 7, 0x98cc, { 0x0000000e, 0x0000000e, 0x0000000e } },
+};
+
+
+
+/***************************\
+* RF2315/RF2316 (Cobra SoC) *
+\***************************/
+
+/* BANK 2				len  pos col */
+#define	AR5K_RF2316_RF_TURBO		{ 1, 1,   2 }
+
+/* BANK 6				len  pos col */
+#define	AR5K_RF2316_OB_2GHZ		{ 3, 178, 0 }
+#define	AR5K_RF2316_DB_2GHZ		{ 3, 175, 0 }
+
+static const struct ath5k_rf_reg rf_regs_2316[] = {
+	{2, AR5K_RF_TURBO,		AR5K_RF2316_RF_TURBO},
+	{6, AR5K_RF_OB_2GHZ,		AR5K_RF2316_OB_2GHZ},
+	{6, AR5K_RF_DB_2GHZ,		AR5K_RF2316_DB_2GHZ},
+};
+
+/* Default mode specific settings */
+static const struct ath5k_ini_rfbuffer rfb_2316[] = {
+	/* BANK / C.R.     A/XR         B           G      */
+	{ 1, 0x98d4, { 0x00000020, 0x00000020, 0x00000020 } },
+	{ 2, 0x98d0, { 0x02001408, 0x02001408, 0x02001408 } },
+	{ 3, 0x98dc, { 0x00a020c0, 0x00e020c0, 0x00e020c0 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0xc0000000, 0xc0000000, 0xc0000000 } },
+	{ 6, 0x989c, { 0x0f000000, 0x0f000000, 0x0f000000 } },
+	{ 6, 0x989c, { 0x02000000, 0x02000000, 0x02000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0xf8000000, 0xf8000000, 0xf8000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x95150000, 0x95150000, 0x95150000 } },
+	{ 6, 0x989c, { 0xc1000000, 0xc1000000, 0xc1000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00080000, 0x00080000, 0x00080000 } },
+	{ 6, 0x989c, { 0x00d50000, 0x00d50000, 0x00d50000 } },
+	{ 6, 0x989c, { 0x000e0000, 0x000e0000, 0x000e0000 } },
+	{ 6, 0x989c, { 0x00dc0000, 0x00dc0000, 0x00dc0000 } },
+	{ 6, 0x989c, { 0x00770000, 0x00770000, 0x00770000 } },
+	{ 6, 0x989c, { 0x008a0000, 0x008a0000, 0x008a0000 } },
+	{ 6, 0x989c, { 0x10880000, 0x10880000, 0x10880000 } },
+	{ 6, 0x989c, { 0x008c0060, 0x008c0060, 0x008c0060 } },
+	{ 6, 0x989c, { 0x00a00000, 0x00a00080, 0x00a00080 } },
+	{ 6, 0x989c, { 0x00400000, 0x0040000d, 0x0040000d } },
+	{ 6, 0x989c, { 0x00110400, 0x00110400, 0x00110400 } },
+	{ 6, 0x989c, { 0x00000060, 0x00000060, 0x00000060 } },
+	{ 6, 0x989c, { 0x00000001, 0x00000001, 0x00000001 } },
+	{ 6, 0x989c, { 0x00000b00, 0x00000b00, 0x00000b00 } },
+	{ 6, 0x989c, { 0x00000be8, 0x00000be8, 0x00000be8 } },
+	{ 6, 0x98c0, { 0x00010000, 0x00010000, 0x00010000 } },
+	{ 7, 0x989c, { 0x00006400, 0x00006400, 0x00006400 } },
+	{ 7, 0x989c, { 0x00000800, 0x00000800, 0x00000800 } },
+	{ 7, 0x98cc, { 0x0000000e, 0x0000000e, 0x0000000e } },
+};
+
+
+
+/******************************\
+* RF5413/RF5424 (Eagle/Condor) *
+\******************************/
+
+/* BANK 6				len  pos col */
+#define	AR5K_RF5413_OB_2GHZ		{ 3, 241, 0 }
+#define	AR5K_RF5413_DB_2GHZ		{ 3, 238, 0 }
+
+#define	AR5K_RF5413_OB_5GHZ		{ 3, 247, 0 }
+#define	AR5K_RF5413_DB_5GHZ		{ 3, 244, 0 }
+
+#define	AR5K_RF5413_PWD_ICLOBUF2G	{ 3, 131, 3 }
+#define	AR5K_RF5413_DERBY_CHAN_SEL_MODE	{ 1, 291, 2 }
+
+static const struct ath5k_rf_reg rf_regs_5413[] = {
+	{6, AR5K_RF_OB_2GHZ,		 AR5K_RF5413_OB_2GHZ},
+	{6, AR5K_RF_DB_2GHZ,		 AR5K_RF5413_DB_2GHZ},
+	{6, AR5K_RF_OB_5GHZ,		 AR5K_RF5413_OB_5GHZ},
+	{6, AR5K_RF_DB_5GHZ,		 AR5K_RF5413_DB_5GHZ},
+	{6, AR5K_RF_PWD_ICLOBUF_2G,	 AR5K_RF5413_PWD_ICLOBUF2G},
+	{6, AR5K_RF_DERBY_CHAN_SEL_MODE, AR5K_RF5413_DERBY_CHAN_SEL_MODE},
+};
+
+/* Default mode specific settings */
+static const struct ath5k_ini_rfbuffer rfb_5413[] = {
+	/* BANK / C.R.     A/XR         B           G      */
+	{ 1, 0x98d4, { 0x00000020, 0x00000020, 0x00000020 } },
+	{ 2, 0x98d0, { 0x00000008, 0x00000008, 0x00000008 } },
+	{ 3, 0x98dc, { 0x00a000c0, 0x00e000c0, 0x00e000c0 } },
+	{ 6, 0x989c, { 0x33000000, 0x33000000, 0x33000000 } },
+	{ 6, 0x989c, { 0x01000000, 0x01000000, 0x01000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x1f000000, 0x1f000000, 0x1f000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00b80000, 0x00b80000, 0x00b80000 } },
+	{ 6, 0x989c, { 0x00b70000, 0x00b70000, 0x00b70000 } },
+	{ 6, 0x989c, { 0x00840000, 0x00840000, 0x00840000 } },
+	{ 6, 0x989c, { 0x00980000, 0x00980000, 0x00980000 } },
+	{ 6, 0x989c, { 0x00c00000, 0x00c00000, 0x00c00000 } },
+	{ 6, 0x989c, { 0x00ff0000, 0x00ff0000, 0x00ff0000 } },
+	{ 6, 0x989c, { 0x00ff0000, 0x00ff0000, 0x00ff0000 } },
+	{ 6, 0x989c, { 0x00ff0000, 0x00ff0000, 0x00ff0000 } },
+	{ 6, 0x989c, { 0x00ff0000, 0x00ff0000, 0x00ff0000 } },
+	{ 6, 0x989c, { 0x00d70000, 0x00d70000, 0x00d70000 } },
+	{ 6, 0x989c, { 0x00610000, 0x00610000, 0x00610000 } },
+	{ 6, 0x989c, { 0x00fe0000, 0x00fe0000, 0x00fe0000 } },
+	{ 6, 0x989c, { 0x00de0000, 0x00de0000, 0x00de0000 } },
+	{ 6, 0x989c, { 0x007f0000, 0x007f0000, 0x007f0000 } },
+	{ 6, 0x989c, { 0x043d0000, 0x043d0000, 0x043d0000 } },
+	{ 6, 0x989c, { 0x00770000, 0x00770000, 0x00770000 } },
+	{ 6, 0x989c, { 0x00440000, 0x00440000, 0x00440000 } },
+	{ 6, 0x989c, { 0x00980000, 0x00980000, 0x00980000 } },
+	{ 6, 0x989c, { 0x00100080, 0x00100080, 0x00100080 } },
+	{ 6, 0x989c, { 0x0005c034, 0x0005c034, 0x0005c034 } },
+	{ 6, 0x989c, { 0x003100f0, 0x003100f0, 0x003100f0 } },
+	{ 6, 0x989c, { 0x000c011f, 0x000c011f, 0x000c011f } },
+	{ 6, 0x989c, { 0x00510040, 0x00510040, 0x00510040 } },
+	{ 6, 0x989c, { 0x005000da, 0x005000da, 0x005000da } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00004044, 0x00004044, 0x00004044 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x000060c0, 0x000060c0, 0x000060c0 } },
+	{ 6, 0x989c, { 0x00002c00, 0x00003600, 0x00003600 } },
+	{ 6, 0x98c8, { 0x00000403, 0x00040403, 0x00040403 } },
+	{ 7, 0x989c, { 0x00006400, 0x00006400, 0x00006400 } },
+	{ 7, 0x989c, { 0x00000800, 0x00000800, 0x00000800 } },
+	{ 7, 0x98cc, { 0x0000000e, 0x0000000e, 0x0000000e } },
+};
+
+
+
+/***************************\
+* RF2425/RF2417 (Swan/Nala) *
+* AR2317 (Spider SoC)       *
+\***************************/
+
+/* BANK 2				len  pos col */
+#define AR5K_RF2425_RF_TURBO		{ 1, 1,   2 }
+
+/* BANK 6				len  pos col */
+#define	AR5K_RF2425_OB_2GHZ		{ 3, 193, 0 }
+#define	AR5K_RF2425_DB_2GHZ		{ 3, 190, 0 }
+
+static const struct ath5k_rf_reg rf_regs_2425[] = {
+	{2, AR5K_RF_TURBO,		AR5K_RF2425_RF_TURBO},
+	{6, AR5K_RF_OB_2GHZ,		AR5K_RF2425_OB_2GHZ},
+	{6, AR5K_RF_DB_2GHZ,		AR5K_RF2425_DB_2GHZ},
+};
+
+/* Default mode specific settings
+ */
+static const struct ath5k_ini_rfbuffer rfb_2425[] = {
+	/* BANK / C.R.     A/XR         B           G      */
+	{ 1, 0x98d4, { 0x00000020, 0x00000020, 0x00000020 } },
+	{ 2, 0x98d0, { 0x02001408, 0x02001408, 0x02001408 } },
+	{ 3, 0x98dc, { 0x00a020c0, 0x00e020c0, 0x00e020c0 } },
+	{ 6, 0x989c, { 0x10000000, 0x10000000, 0x10000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x002a0000, 0x002a0000, 0x002a0000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00100000, 0x00100000, 0x00100000 } },
+	{ 6, 0x989c, { 0x00020000, 0x00020000, 0x00020000 } },
+	{ 6, 0x989c, { 0x00730000, 0x00730000, 0x00730000 } },
+	{ 6, 0x989c, { 0x00f80000, 0x00f80000, 0x00f80000 } },
+	{ 6, 0x989c, { 0x00e70000, 0x00e70000, 0x00e70000 } },
+	{ 6, 0x989c, { 0x00140000, 0x00140000, 0x00140000 } },
+	{ 6, 0x989c, { 0x00910040, 0x00910040, 0x00910040 } },
+	{ 6, 0x989c, { 0x0007001a, 0x0007001a, 0x0007001a } },
+	{ 6, 0x989c, { 0x00410000, 0x00410000, 0x00410000 } },
+	{ 6, 0x989c, { 0x00810000, 0x00810060, 0x00810060 } },
+	{ 6, 0x989c, { 0x00020800, 0x00020803, 0x00020803 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00001660, 0x00001660, 0x00001660 } },
+	{ 6, 0x989c, { 0x00001688, 0x00001688, 0x00001688 } },
+	{ 6, 0x98c4, { 0x00000001, 0x00000001, 0x00000001 } },
+	{ 7, 0x989c, { 0x00006400, 0x00006400, 0x00006400 } },
+	{ 7, 0x989c, { 0x00000800, 0x00000800, 0x00000800 } },
+	{ 7, 0x98cc, { 0x0000000e, 0x0000000e, 0x0000000e } },
+};
+
+/*
+ * TODO: Handle the few differences with swan during
+ * bank modification and get rid of this
+ */
+static const struct ath5k_ini_rfbuffer rfb_2317[] = {
+	/* BANK / C.R.     A/XR         B           G      */
+	{ 1, 0x98d4, { 0x00000020, 0x00000020, 0x00000020 } },
+	{ 2, 0x98d0, { 0x02001408, 0x02001408, 0x02001408 } },
+	{ 3, 0x98dc, { 0x00a020c0, 0x00e020c0, 0x00e020c0 } },
+	{ 6, 0x989c, { 0x10000000, 0x10000000, 0x10000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x002a0000, 0x002a0000, 0x002a0000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00100000, 0x00100000, 0x00100000 } },
+	{ 6, 0x989c, { 0x00020000, 0x00020000, 0x00020000 } },
+	{ 6, 0x989c, { 0x00730000, 0x00730000, 0x00730000 } },
+	{ 6, 0x989c, { 0x00f80000, 0x00f80000, 0x00f80000 } },
+	{ 6, 0x989c, { 0x00e70000, 0x00e70000, 0x00e70000 } },
+	{ 6, 0x989c, { 0x00140100, 0x00140100, 0x00140100 } },
+	{ 6, 0x989c, { 0x00910040, 0x00910040, 0x00910040 } },
+	{ 6, 0x989c, { 0x0007001a, 0x0007001a, 0x0007001a } },
+	{ 6, 0x989c, { 0x00410000, 0x00410000, 0x00410000 } },
+	{ 6, 0x989c, { 0x00810000, 0x00810060, 0x00810060 } },
+	{ 6, 0x989c, { 0x00020800, 0x00020803, 0x00020803 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00001660, 0x00001660, 0x00001660 } },
+	{ 6, 0x989c, { 0x00009688, 0x00009688, 0x00009688 } },
+	{ 6, 0x98c4, { 0x00000001, 0x00000001, 0x00000001 } },
+	{ 7, 0x989c, { 0x00006400, 0x00006400, 0x00006400 } },
+	{ 7, 0x989c, { 0x00000800, 0x00000800, 0x00000800 } },
+	{ 7, 0x98cc, { 0x0000000e, 0x0000000e, 0x0000000e } },
+};
+
+/*
+ * TODO: Handle the few differences with swan during
+ * bank modification and get rid of this
+ */
+static const struct ath5k_ini_rfbuffer rfb_2417[] = {
+	/* BANK / C.R.     A/XR         B           G      */
+	{ 1, 0x98d4, { 0x00000020, 0x00000020, 0x00000020 } },
+	{ 2, 0x98d0, { 0x02001408, 0x02001408, 0x02001408 } },
+	{ 3, 0x98dc, { 0x00a020c0, 0x00e020c0, 0x00e020c0 } },
+	{ 6, 0x989c, { 0x10000000, 0x10000000, 0x10000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x002a0000, 0x002a0000, 0x002a0000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00100000, 0x00100000, 0x00100000 } },
+	{ 6, 0x989c, { 0x00020000, 0x00020000, 0x00020000 } },
+	{ 6, 0x989c, { 0x00730000, 0x00730000, 0x00730000 } },
+	{ 6, 0x989c, { 0x00f80000, 0x00f80000, 0x00f80000 } },
+	{ 6, 0x989c, { 0x00e70000, 0x80e70000, 0x80e70000 } },
+	{ 6, 0x989c, { 0x00140000, 0x00140000, 0x00140000 } },
+	{ 6, 0x989c, { 0x00910040, 0x00910040, 0x00910040 } },
+	{ 6, 0x989c, { 0x0007001a, 0x0207001a, 0x0207001a } },
+	{ 6, 0x989c, { 0x00410000, 0x00410000, 0x00410000 } },
+	{ 6, 0x989c, { 0x00810000, 0x00810060, 0x00810060 } },
+	{ 6, 0x989c, { 0x00020800, 0x00020803, 0x00020803 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00000000, 0x00000000, 0x00000000 } },
+	{ 6, 0x989c, { 0x00001660, 0x00001660, 0x00001660 } },
+	{ 6, 0x989c, { 0x00001688, 0x00001688, 0x00001688 } },
+	{ 6, 0x98c4, { 0x00000001, 0x00000001, 0x00000001 } },
+	{ 7, 0x989c, { 0x00006400, 0x00006400, 0x00006400 } },
+	{ 7, 0x989c, { 0x00000800, 0x00000800, 0x00000800 } },
+	{ 7, 0x98cc, { 0x0000000e, 0x0000000e, 0x0000000e } },
+};

linux-7.2.3/drivers/net/wireless/ath/ath5k/rfgain.h

@@ -0,0 +1,534 @@
+/*
+ * RF Gain optimization
+ *
+ * Copyright (c) 2004-2009 Reyk Floeter <reyk@openbsd.org>
+ * Copyright (c) 2006-2009 Nick Kossifidis <mickflemm@gmail.com>
+ *
+ * Permission to use, copy, modify, and distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+/**
+ * struct ath5k_ini_rfgain - RF Gain table
+ * @rfg_register: RF Gain register address
+ * @rfg_value: Register value for 5 and 2GHz
+ *
+ * Mode-specific RF Gain table (64bytes) for RF5111/5112
+ * (RF5110 only comes with AR5210 and only supports a/turbo a mode so initial
+ * RF Gain values are included in AR5K_AR5210_INI)
+ */
+struct ath5k_ini_rfgain {
+	u16	rfg_register;
+	u32	rfg_value[2];	/* [freq (see below)] */
+};
+
+/* Initial RF Gain settings for RF5111 */
+static const struct ath5k_ini_rfgain rfgain_5111[] = {
+	/*			      5GHz	2GHz	*/
+	{ AR5K_RF_GAIN(0),	{ 0x000001a9, 0x00000000 } },
+	{ AR5K_RF_GAIN(1),	{ 0x000001e9, 0x00000040 } },
+	{ AR5K_RF_GAIN(2),	{ 0x00000029, 0x00000080 } },
+	{ AR5K_RF_GAIN(3),	{ 0x00000069, 0x00000150 } },
+	{ AR5K_RF_GAIN(4),	{ 0x00000199, 0x00000190 } },
+	{ AR5K_RF_GAIN(5),	{ 0x000001d9, 0x000001d0 } },
+	{ AR5K_RF_GAIN(6),	{ 0x00000019, 0x00000010 } },
+	{ AR5K_RF_GAIN(7),	{ 0x00000059, 0x00000044 } },
+	{ AR5K_RF_GAIN(8),	{ 0x00000099, 0x00000084 } },
+	{ AR5K_RF_GAIN(9),	{ 0x000001a5, 0x00000148 } },
+	{ AR5K_RF_GAIN(10),	{ 0x000001e5, 0x00000188 } },
+	{ AR5K_RF_GAIN(11),	{ 0x00000025, 0x000001c8 } },
+	{ AR5K_RF_GAIN(12),	{ 0x000001c8, 0x00000014 } },
+	{ AR5K_RF_GAIN(13),	{ 0x00000008, 0x00000042 } },
+	{ AR5K_RF_GAIN(14),	{ 0x00000048, 0x00000082 } },
+	{ AR5K_RF_GAIN(15),	{ 0x00000088, 0x00000178 } },
+	{ AR5K_RF_GAIN(16),	{ 0x00000198, 0x000001b8 } },
+	{ AR5K_RF_GAIN(17),	{ 0x000001d8, 0x000001f8 } },
+	{ AR5K_RF_GAIN(18),	{ 0x00000018, 0x00000012 } },
+	{ AR5K_RF_GAIN(19),	{ 0x00000058, 0x00000052 } },
+	{ AR5K_RF_GAIN(20),	{ 0x00000098, 0x00000092 } },
+	{ AR5K_RF_GAIN(21),	{ 0x000001a4, 0x0000017c } },
+	{ AR5K_RF_GAIN(22),	{ 0x000001e4, 0x000001bc } },
+	{ AR5K_RF_GAIN(23),	{ 0x00000024, 0x000001fc } },
+	{ AR5K_RF_GAIN(24),	{ 0x00000064, 0x0000000a } },
+	{ AR5K_RF_GAIN(25),	{ 0x000000a4, 0x0000004a } },
+	{ AR5K_RF_GAIN(26),	{ 0x000000e4, 0x0000008a } },
+	{ AR5K_RF_GAIN(27),	{ 0x0000010a, 0x0000015a } },
+	{ AR5K_RF_GAIN(28),	{ 0x0000014a, 0x0000019a } },
+	{ AR5K_RF_GAIN(29),	{ 0x0000018a, 0x000001da } },
+	{ AR5K_RF_GAIN(30),	{ 0x000001ca, 0x0000000e } },
+	{ AR5K_RF_GAIN(31),	{ 0x0000000a, 0x0000004e } },
+	{ AR5K_RF_GAIN(32),	{ 0x0000004a, 0x0000008e } },
+	{ AR5K_RF_GAIN(33),	{ 0x0000008a, 0x0000015e } },
+	{ AR5K_RF_GAIN(34),	{ 0x000001ba, 0x0000019e } },
+	{ AR5K_RF_GAIN(35),	{ 0x000001fa, 0x000001de } },
+	{ AR5K_RF_GAIN(36),	{ 0x0000003a, 0x00000009 } },
+	{ AR5K_RF_GAIN(37),	{ 0x0000007a, 0x00000049 } },
+	{ AR5K_RF_GAIN(38),	{ 0x00000186, 0x00000089 } },
+	{ AR5K_RF_GAIN(39),	{ 0x000001c6, 0x00000179 } },
+	{ AR5K_RF_GAIN(40),	{ 0x00000006, 0x000001b9 } },
+	{ AR5K_RF_GAIN(41),	{ 0x00000046, 0x000001f9 } },
+	{ AR5K_RF_GAIN(42),	{ 0x00000086, 0x00000039 } },
+	{ AR5K_RF_GAIN(43),	{ 0x000000c6, 0x00000079 } },
+	{ AR5K_RF_GAIN(44),	{ 0x000000c6, 0x000000b9 } },
+	{ AR5K_RF_GAIN(45),	{ 0x000000c6, 0x000001bd } },
+	{ AR5K_RF_GAIN(46),	{ 0x000000c6, 0x000001fd } },
+	{ AR5K_RF_GAIN(47),	{ 0x000000c6, 0x0000003d } },
+	{ AR5K_RF_GAIN(48),	{ 0x000000c6, 0x0000007d } },
+	{ AR5K_RF_GAIN(49),	{ 0x000000c6, 0x000000bd } },
+	{ AR5K_RF_GAIN(50),	{ 0x000000c6, 0x000000fd } },
+	{ AR5K_RF_GAIN(51),	{ 0x000000c6, 0x000000fd } },
+	{ AR5K_RF_GAIN(52),	{ 0x000000c6, 0x000000fd } },
+	{ AR5K_RF_GAIN(53),	{ 0x000000c6, 0x000000fd } },
+	{ AR5K_RF_GAIN(54),	{ 0x000000c6, 0x000000fd } },
+	{ AR5K_RF_GAIN(55),	{ 0x000000c6, 0x000000fd } },
+	{ AR5K_RF_GAIN(56),	{ 0x000000c6, 0x000000fd } },
+	{ AR5K_RF_GAIN(57),	{ 0x000000c6, 0x000000fd } },
+	{ AR5K_RF_GAIN(58),	{ 0x000000c6, 0x000000fd } },
+	{ AR5K_RF_GAIN(59),	{ 0x000000c6, 0x000000fd } },
+	{ AR5K_RF_GAIN(60),	{ 0x000000c6, 0x000000fd } },
+	{ AR5K_RF_GAIN(61),	{ 0x000000c6, 0x000000fd } },
+	{ AR5K_RF_GAIN(62),	{ 0x000000c6, 0x000000fd } },
+	{ AR5K_RF_GAIN(63),	{ 0x000000c6, 0x000000fd } },
+};
+
+/* Initial RF Gain settings for RF5112 */
+static const struct ath5k_ini_rfgain rfgain_5112[] = {
+	/*			      5GHz	2GHz	*/
+	{ AR5K_RF_GAIN(0),	{ 0x00000007, 0x00000007 } },
+	{ AR5K_RF_GAIN(1),	{ 0x00000047, 0x00000047 } },
+	{ AR5K_RF_GAIN(2),	{ 0x00000087, 0x00000087 } },
+	{ AR5K_RF_GAIN(3),	{ 0x000001a0, 0x000001a0 } },
+	{ AR5K_RF_GAIN(4),	{ 0x000001e0, 0x000001e0 } },
+	{ AR5K_RF_GAIN(5),	{ 0x00000020, 0x00000020 } },
+	{ AR5K_RF_GAIN(6),	{ 0x00000060, 0x00000060 } },
+	{ AR5K_RF_GAIN(7),	{ 0x000001a1, 0x000001a1 } },
+	{ AR5K_RF_GAIN(8),	{ 0x000001e1, 0x000001e1 } },
+	{ AR5K_RF_GAIN(9),	{ 0x00000021, 0x00000021 } },
+	{ AR5K_RF_GAIN(10),	{ 0x00000061, 0x00000061 } },
+	{ AR5K_RF_GAIN(11),	{ 0x00000162, 0x00000162 } },
+	{ AR5K_RF_GAIN(12),	{ 0x000001a2, 0x000001a2 } },
+	{ AR5K_RF_GAIN(13),	{ 0x000001e2, 0x000001e2 } },
+	{ AR5K_RF_GAIN(14),	{ 0x00000022, 0x00000022 } },
+	{ AR5K_RF_GAIN(15),	{ 0x00000062, 0x00000062 } },
+	{ AR5K_RF_GAIN(16),	{ 0x00000163, 0x00000163 } },
+	{ AR5K_RF_GAIN(17),	{ 0x000001a3, 0x000001a3 } },
+	{ AR5K_RF_GAIN(18),	{ 0x000001e3, 0x000001e3 } },
+	{ AR5K_RF_GAIN(19),	{ 0x00000023, 0x00000023 } },
+	{ AR5K_RF_GAIN(20),	{ 0x00000063, 0x00000063 } },
+	{ AR5K_RF_GAIN(21),	{ 0x00000184, 0x00000184 } },
+	{ AR5K_RF_GAIN(22),	{ 0x000001c4, 0x000001c4 } },
+	{ AR5K_RF_GAIN(23),	{ 0x00000004, 0x00000004 } },
+	{ AR5K_RF_GAIN(24),	{ 0x000001ea, 0x0000000b } },
+	{ AR5K_RF_GAIN(25),	{ 0x0000002a, 0x0000004b } },
+	{ AR5K_RF_GAIN(26),	{ 0x0000006a, 0x0000008b } },
+	{ AR5K_RF_GAIN(27),	{ 0x000000aa, 0x000001ac } },
+	{ AR5K_RF_GAIN(28),	{ 0x000001ab, 0x000001ec } },
+	{ AR5K_RF_GAIN(29),	{ 0x000001eb, 0x0000002c } },
+	{ AR5K_RF_GAIN(30),	{ 0x0000002b, 0x00000012 } },
+	{ AR5K_RF_GAIN(31),	{ 0x0000006b, 0x00000052 } },
+	{ AR5K_RF_GAIN(32),	{ 0x000000ab, 0x00000092 } },
+	{ AR5K_RF_GAIN(33),	{ 0x000001ac, 0x00000193 } },
+	{ AR5K_RF_GAIN(34),	{ 0x000001ec, 0x000001d3 } },
+	{ AR5K_RF_GAIN(35),	{ 0x0000002c, 0x00000013 } },
+	{ AR5K_RF_GAIN(36),	{ 0x0000003a, 0x00000053 } },
+	{ AR5K_RF_GAIN(37),	{ 0x0000007a, 0x00000093 } },
+	{ AR5K_RF_GAIN(38),	{ 0x000000ba, 0x00000194 } },
+	{ AR5K_RF_GAIN(39),	{ 0x000001bb, 0x000001d4 } },
+	{ AR5K_RF_GAIN(40),	{ 0x000001fb, 0x00000014 } },
+	{ AR5K_RF_GAIN(41),	{ 0x0000003b, 0x0000003a } },
+	{ AR5K_RF_GAIN(42),	{ 0x0000007b, 0x0000007a } },
+	{ AR5K_RF_GAIN(43),	{ 0x000000bb, 0x000000ba } },
+	{ AR5K_RF_GAIN(44),	{ 0x000001bc, 0x000001bb } },
+	{ AR5K_RF_GAIN(45),	{ 0x000001fc, 0x000001fb } },
+	{ AR5K_RF_GAIN(46),	{ 0x0000003c, 0x0000003b } },
+	{ AR5K_RF_GAIN(47),	{ 0x0000007c, 0x0000007b } },
+	{ AR5K_RF_GAIN(48),	{ 0x000000bc, 0x000000bb } },
+	{ AR5K_RF_GAIN(49),	{ 0x000000fc, 0x000001bc } },
+	{ AR5K_RF_GAIN(50),	{ 0x000000fc, 0x000001fc } },
+	{ AR5K_RF_GAIN(51),	{ 0x000000fc, 0x0000003c } },
+	{ AR5K_RF_GAIN(52),	{ 0x000000fc, 0x0000007c } },
+	{ AR5K_RF_GAIN(53),	{ 0x000000fc, 0x000000bc } },
+	{ AR5K_RF_GAIN(54),	{ 0x000000fc, 0x000000fc } },
+	{ AR5K_RF_GAIN(55),	{ 0x000000fc, 0x000000fc } },
+	{ AR5K_RF_GAIN(56),	{ 0x000000fc, 0x000000fc } },
+	{ AR5K_RF_GAIN(57),	{ 0x000000fc, 0x000000fc } },
+	{ AR5K_RF_GAIN(58),	{ 0x000000fc, 0x000000fc } },
+	{ AR5K_RF_GAIN(59),	{ 0x000000fc, 0x000000fc } },
+	{ AR5K_RF_GAIN(60),	{ 0x000000fc, 0x000000fc } },
+	{ AR5K_RF_GAIN(61),	{ 0x000000fc, 0x000000fc } },
+	{ AR5K_RF_GAIN(62),	{ 0x000000fc, 0x000000fc } },
+	{ AR5K_RF_GAIN(63),	{ 0x000000fc, 0x000000fc } },
+};
+
+/* Initial RF Gain settings for RF2413 */
+static const struct ath5k_ini_rfgain rfgain_2413[] = {
+	{ AR5K_RF_GAIN(0),	{ 0x00000000, 0x00000000 } },
+	{ AR5K_RF_GAIN(1),	{ 0x00000000, 0x00000040 } },
+	{ AR5K_RF_GAIN(2),	{ 0x00000000, 0x00000080 } },
+	{ AR5K_RF_GAIN(3),	{ 0x00000000, 0x00000181 } },
+	{ AR5K_RF_GAIN(4),	{ 0x00000000, 0x000001c1 } },
+	{ AR5K_RF_GAIN(5),	{ 0x00000000, 0x00000001 } },
+	{ AR5K_RF_GAIN(6),	{ 0x00000000, 0x00000041 } },
+	{ AR5K_RF_GAIN(7),	{ 0x00000000, 0x00000081 } },
+	{ AR5K_RF_GAIN(8),	{ 0x00000000, 0x00000168 } },
+	{ AR5K_RF_GAIN(9),	{ 0x00000000, 0x000001a8 } },
+	{ AR5K_RF_GAIN(10),	{ 0x00000000, 0x000001e8 } },
+	{ AR5K_RF_GAIN(11),	{ 0x00000000, 0x00000028 } },
+	{ AR5K_RF_GAIN(12),	{ 0x00000000, 0x00000068 } },
+	{ AR5K_RF_GAIN(13),	{ 0x00000000, 0x00000189 } },
+	{ AR5K_RF_GAIN(14),	{ 0x00000000, 0x000001c9 } },
+	{ AR5K_RF_GAIN(15),	{ 0x00000000, 0x00000009 } },
+	{ AR5K_RF_GAIN(16),	{ 0x00000000, 0x00000049 } },
+	{ AR5K_RF_GAIN(17),	{ 0x00000000, 0x00000089 } },
+	{ AR5K_RF_GAIN(18),	{ 0x00000000, 0x00000190 } },
+	{ AR5K_RF_GAIN(19),	{ 0x00000000, 0x000001d0 } },
+	{ AR5K_RF_GAIN(20),	{ 0x00000000, 0x00000010 } },
+	{ AR5K_RF_GAIN(21),	{ 0x00000000, 0x00000050 } },
+	{ AR5K_RF_GAIN(22),	{ 0x00000000, 0x00000090 } },
+	{ AR5K_RF_GAIN(23),	{ 0x00000000, 0x00000191 } },
+	{ AR5K_RF_GAIN(24),	{ 0x00000000, 0x000001d1 } },
+	{ AR5K_RF_GAIN(25),	{ 0x00000000, 0x00000011 } },
+	{ AR5K_RF_GAIN(26),	{ 0x00000000, 0x00000051 } },
+	{ AR5K_RF_GAIN(27),	{ 0x00000000, 0x00000091 } },
+	{ AR5K_RF_GAIN(28),	{ 0x00000000, 0x00000178 } },
+	{ AR5K_RF_GAIN(29),	{ 0x00000000, 0x000001b8 } },
+	{ AR5K_RF_GAIN(30),	{ 0x00000000, 0x000001f8 } },
+	{ AR5K_RF_GAIN(31),	{ 0x00000000, 0x00000038 } },
+	{ AR5K_RF_GAIN(32),	{ 0x00000000, 0x00000078 } },
+	{ AR5K_RF_GAIN(33),	{ 0x00000000, 0x00000199 } },
+	{ AR5K_RF_GAIN(34),	{ 0x00000000, 0x000001d9 } },
+	{ AR5K_RF_GAIN(35),	{ 0x00000000, 0x00000019 } },
+	{ AR5K_RF_GAIN(36),	{ 0x00000000, 0x00000059 } },
+	{ AR5K_RF_GAIN(37),	{ 0x00000000, 0x00000099 } },
+	{ AR5K_RF_GAIN(38),	{ 0x00000000, 0x000000d9 } },
+	{ AR5K_RF_GAIN(39),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(40),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(41),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(42),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(43),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(44),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(45),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(46),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(47),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(48),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(49),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(50),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(51),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(52),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(53),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(54),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(55),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(56),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(57),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(58),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(59),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(60),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(61),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(62),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(63),	{ 0x00000000, 0x000000f9 } },
+};
+
+/* Initial RF Gain settings for AR2316 */
+static const struct ath5k_ini_rfgain rfgain_2316[] = {
+	{ AR5K_RF_GAIN(0),	{ 0x00000000, 0x00000000 } },
+	{ AR5K_RF_GAIN(1),	{ 0x00000000, 0x00000040 } },
+	{ AR5K_RF_GAIN(2),	{ 0x00000000, 0x00000080 } },
+	{ AR5K_RF_GAIN(3),	{ 0x00000000, 0x000000c0 } },
+	{ AR5K_RF_GAIN(4),	{ 0x00000000, 0x000000e0 } },
+	{ AR5K_RF_GAIN(5),	{ 0x00000000, 0x000000e0 } },
+	{ AR5K_RF_GAIN(6),	{ 0x00000000, 0x00000128 } },
+	{ AR5K_RF_GAIN(7),	{ 0x00000000, 0x00000128 } },
+	{ AR5K_RF_GAIN(8),	{ 0x00000000, 0x00000128 } },
+	{ AR5K_RF_GAIN(9),	{ 0x00000000, 0x00000168 } },
+	{ AR5K_RF_GAIN(10),	{ 0x00000000, 0x000001a8 } },
+	{ AR5K_RF_GAIN(11),	{ 0x00000000, 0x000001e8 } },
+	{ AR5K_RF_GAIN(12),	{ 0x00000000, 0x00000028 } },
+	{ AR5K_RF_GAIN(13),	{ 0x00000000, 0x00000068 } },
+	{ AR5K_RF_GAIN(14),	{ 0x00000000, 0x000000a8 } },
+	{ AR5K_RF_GAIN(15),	{ 0x00000000, 0x000000e8 } },
+	{ AR5K_RF_GAIN(16),	{ 0x00000000, 0x000000e8 } },
+	{ AR5K_RF_GAIN(17),	{ 0x00000000, 0x00000130 } },
+	{ AR5K_RF_GAIN(18),	{ 0x00000000, 0x00000130 } },
+	{ AR5K_RF_GAIN(19),	{ 0x00000000, 0x00000170 } },
+	{ AR5K_RF_GAIN(20),	{ 0x00000000, 0x000001b0 } },
+	{ AR5K_RF_GAIN(21),	{ 0x00000000, 0x000001f0 } },
+	{ AR5K_RF_GAIN(22),	{ 0x00000000, 0x00000030 } },
+	{ AR5K_RF_GAIN(23),	{ 0x00000000, 0x00000070 } },
+	{ AR5K_RF_GAIN(24),	{ 0x00000000, 0x000000b0 } },
+	{ AR5K_RF_GAIN(25),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(26),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(27),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(28),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(29),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(30),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(31),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(32),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(33),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(34),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(35),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(36),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(37),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(38),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(39),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(40),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(41),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(42),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(43),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(44),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(45),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(46),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(47),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(48),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(49),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(50),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(51),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(52),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(53),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(54),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(55),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(56),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(57),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(58),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(59),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(60),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(61),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(62),	{ 0x00000000, 0x000000f0 } },
+	{ AR5K_RF_GAIN(63),	{ 0x00000000, 0x000000f0 } },
+};
+
+
+/* Initial RF Gain settings for RF5413 */
+static const struct ath5k_ini_rfgain rfgain_5413[] = {
+	/*			      5GHz	2GHz	*/
+	{ AR5K_RF_GAIN(0),	{ 0x00000000, 0x00000000 } },
+	{ AR5K_RF_GAIN(1),	{ 0x00000040, 0x00000040 } },
+	{ AR5K_RF_GAIN(2),	{ 0x00000080, 0x00000080 } },
+	{ AR5K_RF_GAIN(3),	{ 0x000001a1, 0x00000161 } },
+	{ AR5K_RF_GAIN(4),	{ 0x000001e1, 0x000001a1 } },
+	{ AR5K_RF_GAIN(5),	{ 0x00000021, 0x000001e1 } },
+	{ AR5K_RF_GAIN(6),	{ 0x00000061, 0x00000021 } },
+	{ AR5K_RF_GAIN(7),	{ 0x00000188, 0x00000061 } },
+	{ AR5K_RF_GAIN(8),	{ 0x000001c8, 0x00000188 } },
+	{ AR5K_RF_GAIN(9),	{ 0x00000008, 0x000001c8 } },
+	{ AR5K_RF_GAIN(10),	{ 0x00000048, 0x00000008 } },
+	{ AR5K_RF_GAIN(11),	{ 0x00000088, 0x00000048 } },
+	{ AR5K_RF_GAIN(12),	{ 0x000001a9, 0x00000088 } },
+	{ AR5K_RF_GAIN(13),	{ 0x000001e9, 0x00000169 } },
+	{ AR5K_RF_GAIN(14),	{ 0x00000029, 0x000001a9 } },
+	{ AR5K_RF_GAIN(15),	{ 0x00000069, 0x000001e9 } },
+	{ AR5K_RF_GAIN(16),	{ 0x000001d0, 0x00000029 } },
+	{ AR5K_RF_GAIN(17),	{ 0x00000010, 0x00000069 } },
+	{ AR5K_RF_GAIN(18),	{ 0x00000050, 0x00000190 } },
+	{ AR5K_RF_GAIN(19),	{ 0x00000090, 0x000001d0 } },
+	{ AR5K_RF_GAIN(20),	{ 0x000001b1, 0x00000010 } },
+	{ AR5K_RF_GAIN(21),	{ 0x000001f1, 0x00000050 } },
+	{ AR5K_RF_GAIN(22),	{ 0x00000031, 0x00000090 } },
+	{ AR5K_RF_GAIN(23),	{ 0x00000071, 0x00000171 } },
+	{ AR5K_RF_GAIN(24),	{ 0x000001b8, 0x000001b1 } },
+	{ AR5K_RF_GAIN(25),	{ 0x000001f8, 0x000001f1 } },
+	{ AR5K_RF_GAIN(26),	{ 0x00000038, 0x00000031 } },
+	{ AR5K_RF_GAIN(27),	{ 0x00000078, 0x00000071 } },
+	{ AR5K_RF_GAIN(28),	{ 0x00000199, 0x00000198 } },
+	{ AR5K_RF_GAIN(29),	{ 0x000001d9, 0x000001d8 } },
+	{ AR5K_RF_GAIN(30),	{ 0x00000019, 0x00000018 } },
+	{ AR5K_RF_GAIN(31),	{ 0x00000059, 0x00000058 } },
+	{ AR5K_RF_GAIN(32),	{ 0x00000099, 0x00000098 } },
+	{ AR5K_RF_GAIN(33),	{ 0x000000d9, 0x00000179 } },
+	{ AR5K_RF_GAIN(34),	{ 0x000000f9, 0x000001b9 } },
+	{ AR5K_RF_GAIN(35),	{ 0x000000f9, 0x000001f9 } },
+	{ AR5K_RF_GAIN(36),	{ 0x000000f9, 0x00000039 } },
+	{ AR5K_RF_GAIN(37),	{ 0x000000f9, 0x00000079 } },
+	{ AR5K_RF_GAIN(38),	{ 0x000000f9, 0x000000b9 } },
+	{ AR5K_RF_GAIN(39),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(40),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(41),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(42),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(43),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(44),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(45),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(46),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(47),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(48),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(49),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(50),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(51),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(52),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(53),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(54),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(55),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(56),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(57),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(58),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(59),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(60),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(61),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(62),	{ 0x000000f9, 0x000000f9 } },
+	{ AR5K_RF_GAIN(63),	{ 0x000000f9, 0x000000f9 } },
+};
+
+
+/* Initial RF Gain settings for RF2425 */
+static const struct ath5k_ini_rfgain rfgain_2425[] = {
+	{ AR5K_RF_GAIN(0),	{ 0x00000000, 0x00000000 } },
+	{ AR5K_RF_GAIN(1),	{ 0x00000000, 0x00000040 } },
+	{ AR5K_RF_GAIN(2),	{ 0x00000000, 0x00000080 } },
+	{ AR5K_RF_GAIN(3),	{ 0x00000000, 0x00000181 } },
+	{ AR5K_RF_GAIN(4),	{ 0x00000000, 0x000001c1 } },
+	{ AR5K_RF_GAIN(5),	{ 0x00000000, 0x00000001 } },
+	{ AR5K_RF_GAIN(6),	{ 0x00000000, 0x00000041 } },
+	{ AR5K_RF_GAIN(7),	{ 0x00000000, 0x00000081 } },
+	{ AR5K_RF_GAIN(8),	{ 0x00000000, 0x00000188 } },
+	{ AR5K_RF_GAIN(9),	{ 0x00000000, 0x000001c8 } },
+	{ AR5K_RF_GAIN(10),	{ 0x00000000, 0x00000008 } },
+	{ AR5K_RF_GAIN(11),	{ 0x00000000, 0x00000048 } },
+	{ AR5K_RF_GAIN(12),	{ 0x00000000, 0x00000088 } },
+	{ AR5K_RF_GAIN(13),	{ 0x00000000, 0x00000189 } },
+	{ AR5K_RF_GAIN(14),	{ 0x00000000, 0x000001c9 } },
+	{ AR5K_RF_GAIN(15),	{ 0x00000000, 0x00000009 } },
+	{ AR5K_RF_GAIN(16),	{ 0x00000000, 0x00000049 } },
+	{ AR5K_RF_GAIN(17),	{ 0x00000000, 0x00000089 } },
+	{ AR5K_RF_GAIN(18),	{ 0x00000000, 0x000001b0 } },
+	{ AR5K_RF_GAIN(19),	{ 0x00000000, 0x000001f0 } },
+	{ AR5K_RF_GAIN(20),	{ 0x00000000, 0x00000030 } },
+	{ AR5K_RF_GAIN(21),	{ 0x00000000, 0x00000070 } },
+	{ AR5K_RF_GAIN(22),	{ 0x00000000, 0x00000171 } },
+	{ AR5K_RF_GAIN(23),	{ 0x00000000, 0x000001b1 } },
+	{ AR5K_RF_GAIN(24),	{ 0x00000000, 0x000001f1 } },
+	{ AR5K_RF_GAIN(25),	{ 0x00000000, 0x00000031 } },
+	{ AR5K_RF_GAIN(26),	{ 0x00000000, 0x00000071 } },
+	{ AR5K_RF_GAIN(27),	{ 0x00000000, 0x000001b8 } },
+	{ AR5K_RF_GAIN(28),	{ 0x00000000, 0x000001f8 } },
+	{ AR5K_RF_GAIN(29),	{ 0x00000000, 0x00000038 } },
+	{ AR5K_RF_GAIN(30),	{ 0x00000000, 0x00000078 } },
+	{ AR5K_RF_GAIN(31),	{ 0x00000000, 0x000000b8 } },
+	{ AR5K_RF_GAIN(32),	{ 0x00000000, 0x000001b9 } },
+	{ AR5K_RF_GAIN(33),	{ 0x00000000, 0x000001f9 } },
+	{ AR5K_RF_GAIN(34),	{ 0x00000000, 0x00000039 } },
+	{ AR5K_RF_GAIN(35),	{ 0x00000000, 0x00000079 } },
+	{ AR5K_RF_GAIN(36),	{ 0x00000000, 0x000000b9 } },
+	{ AR5K_RF_GAIN(37),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(38),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(39),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(40),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(41),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(42),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(43),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(44),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(45),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(46),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(47),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(48),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(49),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(50),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(51),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(52),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(53),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(54),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(55),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(56),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(57),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(58),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(59),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(60),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(61),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(62),	{ 0x00000000, 0x000000f9 } },
+	{ AR5K_RF_GAIN(63),	{ 0x00000000, 0x000000f9 } },
+};
+
+#define AR5K_GAIN_CRN_FIX_BITS_5111		4
+#define AR5K_GAIN_CRN_FIX_BITS_5112		7
+#define AR5K_GAIN_CRN_MAX_FIX_BITS		AR5K_GAIN_CRN_FIX_BITS_5112
+#define AR5K_GAIN_DYN_ADJUST_HI_MARGIN		15
+#define AR5K_GAIN_DYN_ADJUST_LO_MARGIN		20
+#define AR5K_GAIN_CCK_PROBE_CORR		5
+#define AR5K_GAIN_CCK_OFDM_GAIN_DELTA		15
+#define AR5K_GAIN_STEP_COUNT			10
+
+/* Check if our current measurement is inside our
+ * current variable attenuation window */
+#define AR5K_GAIN_CHECK_ADJUST(_g)		\
+	((_g)->g_current <= (_g)->g_low || (_g)->g_current >= (_g)->g_high)
+
+/**
+ * struct ath5k_gain_opt_step - An RF gain optimization step
+ * @gos_param: Set of parameters
+ * @gos_gain: Gain
+ */
+struct ath5k_gain_opt_step {
+	s8				gos_param[AR5K_GAIN_CRN_MAX_FIX_BITS];
+	s8				gos_gain;
+};
+
+/**
+ * struct ath5k_gain_opt - RF Gain optimization ladder
+ * @go_default: The default step
+ * @go_steps_count: How many optimization steps
+ * @go_step: Array of &struct ath5k_gain_opt_step
+ */
+struct ath5k_gain_opt {
+	u8				go_default;
+	u8				go_steps_count;
+	const struct ath5k_gain_opt_step	go_step[AR5K_GAIN_STEP_COUNT];
+};
+
+
+/*
+ * RF5111
+ * Parameters on gos_param:
+ * 1) Tx clip PHY register
+ * 2) PWD 90 RF register
+ * 3) PWD 84 RF register
+ * 4) RFGainSel RF register
+ */
+static const struct ath5k_gain_opt rfgain_opt_5111 = {
+	4,
+	9,
+	{
+		{ { 4, 1, 1, 1 }, 6 },
+		{ { 4, 0, 1, 1 }, 4 },
+		{ { 3, 1, 1, 1 }, 3 },
+		{ { 4, 0, 0, 1 }, 1 },
+		{ { 4, 1, 1, 0 }, 0 },
+		{ { 4, 0, 1, 0 }, -2 },
+		{ { 3, 1, 1, 0 }, -3 },
+		{ { 4, 0, 0, 0 }, -4 },
+		{ { 2, 1, 1, 0 }, -6 }
+	}
+};
+
+/*
+ * RF5112
+ * Parameters on gos_param:
+ * 1) Mixgain ovr RF register
+ * 2) PWD 138 RF register
+ * 3) PWD 137 RF register
+ * 4) PWD 136 RF register
+ * 5) PWD 132 RF register
+ * 6) PWD 131 RF register
+ * 7) PWD 130 RF register
+ */
+static const struct ath5k_gain_opt rfgain_opt_5112 = {
+	1,
+	8,
+	{
+		{ { 3, 0, 0, 0, 0, 0, 0 }, 6 },
+		{ { 2, 0, 0, 0, 0, 0, 0 }, 0 },
+		{ { 1, 0, 0, 0, 0, 0, 0 }, -3 },
+		{ { 0, 0, 0, 0, 0, 0, 0 }, -6 },
+		{ { 0, 1, 1, 0, 0, 0, 0 }, -8 },
+		{ { 0, 1, 1, 0, 1, 1, 0 }, -10 },
+		{ { 0, 1, 0, 1, 1, 1, 0 }, -13 },
+		{ { 0, 1, 0, 1, 1, 0, 1 }, -16 },
+	}
+};
+

linux-7.2.3/drivers/net/wireless/ath/ath5k/rfkill.c

@@ -0,0 +1,115 @@
+/*
+ * RFKILL support for ath5k
+ *
+ * Copyright (c) 2009 Tobias Doerffel <tobias.doerffel@gmail.com>
+ *
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer,
+ *    without modification.
+ * 2. Redistributions in binary form must reproduce at minimum a disclaimer
+ *    similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
+ *    redistribution must be conditioned upon including a substantially
+ *    similar Disclaimer requirement for further binary redistribution.
+ * 3. Neither the names of the above-listed copyright holders nor the names
+ *    of any contributors may be used to endorse or promote products derived
+ *    from this software without specific prior written permission.
+ *
+ * NO WARRANTY
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
+ * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
+ * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
+ * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
+ * THE POSSIBILITY OF SUCH DAMAGES.
+ */
+
+#include "ath5k.h"
+
+
+static inline void ath5k_rfkill_disable(struct ath5k_hw *ah)
+{
+	ATH5K_DBG(ah, ATH5K_DEBUG_ANY, "rfkill disable (gpio:%d polarity:%d)\n",
+		ah->rf_kill.gpio, ah->rf_kill.polarity);
+	ath5k_hw_set_gpio_output(ah, ah->rf_kill.gpio);
+	ath5k_hw_set_gpio(ah, ah->rf_kill.gpio, !ah->rf_kill.polarity);
+}
+
+
+static inline void ath5k_rfkill_enable(struct ath5k_hw *ah)
+{
+	ATH5K_DBG(ah, ATH5K_DEBUG_ANY, "rfkill enable (gpio:%d polarity:%d)\n",
+		ah->rf_kill.gpio, ah->rf_kill.polarity);
+	ath5k_hw_set_gpio_output(ah, ah->rf_kill.gpio);
+	ath5k_hw_set_gpio(ah, ah->rf_kill.gpio, ah->rf_kill.polarity);
+}
+
+static inline void ath5k_rfkill_set_intr(struct ath5k_hw *ah, bool enable)
+{
+	u32 curval;
+
+	ath5k_hw_set_gpio_input(ah, ah->rf_kill.gpio);
+	curval = ath5k_hw_get_gpio(ah, ah->rf_kill.gpio);
+	ath5k_hw_set_gpio_intr(ah, ah->rf_kill.gpio, enable ?
+					!!curval : !curval);
+}
+
+static bool
+ath5k_is_rfkill_set(struct ath5k_hw *ah)
+{
+	/* configuring GPIO for input for some reason disables rfkill */
+	/*ath5k_hw_set_gpio_input(ah, ah->rf_kill.gpio);*/
+	return ath5k_hw_get_gpio(ah, ah->rf_kill.gpio) ==
+							ah->rf_kill.polarity;
+}
+
+static void
+ath5k_tasklet_rfkill_toggle(struct tasklet_struct *t)
+{
+	struct ath5k_hw *ah = from_tasklet(ah, t, rf_kill.toggleq);
+	bool blocked;
+
+	blocked = ath5k_is_rfkill_set(ah);
+	wiphy_rfkill_set_hw_state(ah->hw->wiphy, blocked);
+}
+
+
+void
+ath5k_rfkill_hw_start(struct ath5k_hw *ah)
+{
+	/* read rfkill GPIO configuration from EEPROM header */
+	ah->rf_kill.gpio = ah->ah_capabilities.cap_eeprom.ee_rfkill_pin;
+	ah->rf_kill.polarity = ah->ah_capabilities.cap_eeprom.ee_rfkill_pol;
+
+	tasklet_setup(&ah->rf_kill.toggleq, ath5k_tasklet_rfkill_toggle);
+
+	ath5k_rfkill_disable(ah);
+
+	/* enable interrupt for rfkill switch */
+	if (AR5K_EEPROM_HDR_RFKILL(ah->ah_capabilities.cap_eeprom.ee_header))
+		ath5k_rfkill_set_intr(ah, true);
+}
+
+
+void
+ath5k_rfkill_hw_stop(struct ath5k_hw *ah)
+{
+	/* disable interrupt for rfkill switch */
+	if (AR5K_EEPROM_HDR_RFKILL(ah->ah_capabilities.cap_eeprom.ee_header))
+		ath5k_rfkill_set_intr(ah, false);
+
+	tasklet_kill(&ah->rf_kill.toggleq);
+
+	/* enable RFKILL when stopping HW so Wifi LED is turned off */
+	ath5k_rfkill_enable(ah);
+}
+

linux-7.2.3/drivers/net/wireless/ath/ath5k/sysfs.c

@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: GPL-2.0
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/device.h>
+#include <linux/pci.h>
+
+#include "ath5k.h"
+#include "reg.h"
+
+#define SIMPLE_SHOW_STORE(name, get, set)				\
+static ssize_t ath5k_attr_show_##name(struct device *dev,		\
+			struct device_attribute *attr,			\
+			char *buf)					\
+{									\
+	struct ieee80211_hw *hw = dev_get_drvdata(dev);			\
+	struct ath5k_hw *ah = hw->priv;				\
+	return sysfs_emit(buf, "%d\n", get);			\
+}									\
+									\
+static ssize_t ath5k_attr_store_##name(struct device *dev,		\
+			struct device_attribute *attr,			\
+			const char *buf, size_t count)			\
+{									\
+	struct ieee80211_hw *hw = dev_get_drvdata(dev);			\
+	struct ath5k_hw *ah = hw->priv;				\
+	int val, ret;							\
+									\
+	ret = kstrtoint(buf, 10, &val);					\
+	if (ret < 0)							\
+		return ret;						\
+	set(ah, val);						\
+	return count;							\
+}									\
+static DEVICE_ATTR(name, 0644,						\
+		   ath5k_attr_show_##name, ath5k_attr_store_##name)
+
+#define SIMPLE_SHOW(name, get)						\
+static ssize_t ath5k_attr_show_##name(struct device *dev,		\
+			struct device_attribute *attr,			\
+			char *buf)					\
+{									\
+	struct ieee80211_hw *hw = dev_get_drvdata(dev);			\
+	struct ath5k_hw *ah = hw->priv;				\
+	return sysfs_emit(buf, "%d\n", get);			\
+}									\
+static DEVICE_ATTR(name, 0444, ath5k_attr_show_##name, NULL)
+
+/*** ANI ***/
+
+SIMPLE_SHOW_STORE(ani_mode, ah->ani_state.ani_mode, ath5k_ani_init);
+SIMPLE_SHOW_STORE(noise_immunity_level, ah->ani_state.noise_imm_level,
+			ath5k_ani_set_noise_immunity_level);
+SIMPLE_SHOW_STORE(spur_level, ah->ani_state.spur_level,
+			ath5k_ani_set_spur_immunity_level);
+SIMPLE_SHOW_STORE(firstep_level, ah->ani_state.firstep_level,
+			ath5k_ani_set_firstep_level);
+SIMPLE_SHOW_STORE(ofdm_weak_signal_detection, ah->ani_state.ofdm_weak_sig,
+			ath5k_ani_set_ofdm_weak_signal_detection);
+SIMPLE_SHOW_STORE(cck_weak_signal_detection, ah->ani_state.cck_weak_sig,
+			ath5k_ani_set_cck_weak_signal_detection);
+SIMPLE_SHOW(spur_level_max, ah->ani_state.max_spur_level);
+
+static ssize_t ath5k_attr_show_noise_immunity_level_max(struct device *dev,
+			struct device_attribute *attr,
+			char *buf)
+{
+	return sysfs_emit(buf, "%d\n", ATH5K_ANI_MAX_NOISE_IMM_LVL);
+}
+static DEVICE_ATTR(noise_immunity_level_max, 0444,
+		   ath5k_attr_show_noise_immunity_level_max, NULL);
+
+static ssize_t ath5k_attr_show_firstep_level_max(struct device *dev,
+			struct device_attribute *attr,
+			char *buf)
+{
+	return sysfs_emit(buf, "%d\n", ATH5K_ANI_MAX_FIRSTEP_LVL);
+}
+static DEVICE_ATTR(firstep_level_max, 0444,
+		   ath5k_attr_show_firstep_level_max, NULL);
+
+static struct attribute *ath5k_sysfs_entries_ani[] = {
+	&dev_attr_ani_mode.attr,
+	&dev_attr_noise_immunity_level.attr,
+	&dev_attr_spur_level.attr,
+	&dev_attr_firstep_level.attr,
+	&dev_attr_ofdm_weak_signal_detection.attr,
+	&dev_attr_cck_weak_signal_detection.attr,
+	&dev_attr_noise_immunity_level_max.attr,
+	&dev_attr_spur_level_max.attr,
+	&dev_attr_firstep_level_max.attr,
+	NULL
+};
+
+static struct attribute_group ath5k_attribute_group_ani = {
+	.name = "ani",
+	.attrs = ath5k_sysfs_entries_ani,
+};
+
+
+/*** register / unregister ***/
+
+int
+ath5k_sysfs_register(struct ath5k_hw *ah)
+{
+	struct device *dev = ah->dev;
+	int err;
+
+	err = sysfs_create_group(&dev->kobj, &ath5k_attribute_group_ani);
+	if (err) {
+		ATH5K_ERR(ah, "failed to create sysfs group\n");
+		return err;
+	}
+
+	return 0;
+}
+
+void
+ath5k_sysfs_unregister(struct ath5k_hw *ah)
+{
+	struct device *dev = ah->dev;
+
+	sysfs_remove_group(&dev->kobj, &ath5k_attribute_group_ani);
+}

linux-7.2.3/drivers/net/wireless/ath/ath5k/trace.h

@@ -0,0 +1,107 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#if !defined(__TRACE_ATH5K_H) || defined(TRACE_HEADER_MULTI_READ)
+#define __TRACE_ATH5K_H
+
+#include <linux/tracepoint.h>
+
+
+#if !defined(CONFIG_ATH5K_TRACER) || defined(__CHECKER__)
+#undef TRACE_EVENT
+#define TRACE_EVENT(name, proto, ...) \
+static inline void trace_ ## name(proto) {}
+#endif
+
+struct sk_buff;
+struct ath5k_txq;
+struct ath5k_tx_status;
+
+#undef TRACE_SYSTEM
+#define TRACE_SYSTEM ath5k
+
+TRACE_EVENT(ath5k_rx,
+	TP_PROTO(struct ath5k_hw *priv, struct sk_buff *skb),
+	TP_ARGS(priv, skb),
+	TP_STRUCT__entry(
+		__field(struct ath5k_hw *, priv)
+		__field(unsigned long, skbaddr)
+		__dynamic_array(u8, frame, skb->len)
+	),
+	TP_fast_assign(
+		__entry->priv = priv;
+		__entry->skbaddr = (unsigned long) skb;
+		memcpy(__get_dynamic_array(frame), skb->data, skb->len);
+	),
+	TP_printk(
+		"[%p] RX skb=%lx", __entry->priv, __entry->skbaddr
+	)
+);
+
+TRACE_EVENT(ath5k_tx,
+	TP_PROTO(struct ath5k_hw *priv, struct sk_buff *skb,
+		 struct ath5k_txq *q),
+
+	TP_ARGS(priv, skb, q),
+
+	TP_STRUCT__entry(
+		__field(struct ath5k_hw *, priv)
+		__field(unsigned long, skbaddr)
+		__field(u8, qnum)
+		__dynamic_array(u8, frame, skb->len)
+	),
+
+	TP_fast_assign(
+		__entry->priv = priv;
+		__entry->skbaddr = (unsigned long) skb;
+		__entry->qnum = (u8) q->qnum;
+		memcpy(__get_dynamic_array(frame), skb->data, skb->len);
+	),
+
+	TP_printk(
+		"[%p] TX skb=%lx q=%d", __entry->priv, __entry->skbaddr,
+		__entry->qnum
+	)
+);
+
+TRACE_EVENT(ath5k_tx_complete,
+	TP_PROTO(struct ath5k_hw *priv, struct sk_buff *skb,
+		 struct ath5k_txq *q, struct ath5k_tx_status *ts),
+
+	TP_ARGS(priv, skb, q, ts),
+
+	TP_STRUCT__entry(
+		__field(struct ath5k_hw *, priv)
+		__field(unsigned long, skbaddr)
+		__field(u8, qnum)
+		__field(u8, ts_status)
+		__field(s8, ts_rssi)
+		__field(u8, ts_antenna)
+	),
+
+	TP_fast_assign(
+		__entry->priv = priv;
+		__entry->skbaddr = (unsigned long) skb;
+		__entry->qnum = (u8) q->qnum;
+		__entry->ts_status = ts->ts_status;
+		__entry->ts_rssi =  ts->ts_rssi;
+		__entry->ts_antenna = ts->ts_antenna;
+	),
+
+	TP_printk(
+		"[%p] TX end skb=%lx q=%d stat=%x rssi=%d ant=%x",
+		__entry->priv, __entry->skbaddr, __entry->qnum,
+		__entry->ts_status, __entry->ts_rssi, __entry->ts_antenna
+	)
+);
+
+#endif /* __TRACE_ATH5K_H */
+
+#if defined(CONFIG_ATH5K_TRACER) && !defined(__CHECKER__)
+
+#undef TRACE_INCLUDE_PATH
+#define TRACE_INCLUDE_PATH .
+#undef TRACE_INCLUDE_FILE
+#define TRACE_INCLUDE_FILE trace
+
+#include <trace/define_trace.h>
+
+#endif