Resguardo inicial

linux-7.2.3/drivers/phy/lantiq/Kconfig

@@ -0,0 +1,21 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Phy drivers for Lantiq / Intel platforms
+#
+config PHY_LANTIQ_VRX200_PCIE
+	tristate "Lantiq VRX200/ARX300 PCIe PHY"
+	depends on SOC_TYPE_XWAY || COMPILE_TEST
+	depends on OF && HAS_IOMEM
+	select GENERIC_PHY
+	select REGMAP_MMIO
+	help
+	  Support for the PCIe PHY(s) on the Lantiq / Intel VRX200 and ARX300
+	  family SoCs.
+	  If unsure, say N.
+
+config PHY_LANTIQ_RCU_USB2
+	tristate "Lantiq XWAY SoC RCU based USB PHY"
+	depends on OF && (SOC_TYPE_XWAY || COMPILE_TEST)
+	select GENERIC_PHY
+	help
+	  Support for the USB PHY(s) on the Lantiq / Intel XWAY family SoCs.

linux-7.2.3/drivers/phy/lantiq/Makefile

@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_PHY_LANTIQ_RCU_USB2)	+= phy-lantiq-rcu-usb2.o
+obj-$(CONFIG_PHY_LANTIQ_VRX200_PCIE)	+= phy-lantiq-vrx200-pcie.o

linux-7.2.3/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c

@@ -0,0 +1,255 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Lantiq XWAY SoC RCU module based USB 1.1/2.0 PHY driver
+ *
+ * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+ * Copyright (C) 2017 Hauke Mehrtens <hauke@hauke-m.de>
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+/* Transmitter HS Pre-Emphasis Enable */
+#define RCU_CFG1_TX_PEE		BIT(0)
+/* Disconnect Threshold */
+#define RCU_CFG1_DIS_THR_MASK	0x00038000
+#define RCU_CFG1_DIS_THR_SHIFT	15
+
+struct ltq_rcu_usb2_bits {
+	u8 hostmode;
+	u8 slave_endianness;
+	u8 host_endianness;
+	bool have_ana_cfg;
+};
+
+struct ltq_rcu_usb2_priv {
+	struct regmap			*regmap;
+	unsigned int			phy_reg_offset;
+	unsigned int			ana_cfg1_reg_offset;
+	const struct ltq_rcu_usb2_bits	*reg_bits;
+	struct device			*dev;
+	struct phy			*phy;
+	struct clk			*phy_gate_clk;
+	struct reset_control		*ctrl_reset;
+	struct reset_control		*phy_reset;
+};
+
+static const struct ltq_rcu_usb2_bits xway_rcu_usb2_reg_bits = {
+	.hostmode = 11,
+	.slave_endianness = 9,
+	.host_endianness = 10,
+	.have_ana_cfg = false,
+};
+
+static const struct ltq_rcu_usb2_bits xrx100_rcu_usb2_reg_bits = {
+	.hostmode = 11,
+	.slave_endianness = 17,
+	.host_endianness = 10,
+	.have_ana_cfg = false,
+};
+
+static const struct ltq_rcu_usb2_bits xrx200_rcu_usb2_reg_bits = {
+	.hostmode = 11,
+	.slave_endianness = 9,
+	.host_endianness = 10,
+	.have_ana_cfg = true,
+};
+
+static const struct of_device_id ltq_rcu_usb2_phy_of_match[] = {
+	{
+		.compatible = "lantiq,ase-usb2-phy",
+		.data = &xway_rcu_usb2_reg_bits,
+	},
+	{
+		.compatible = "lantiq,danube-usb2-phy",
+		.data = &xway_rcu_usb2_reg_bits,
+	},
+	{
+		.compatible = "lantiq,xrx100-usb2-phy",
+		.data = &xrx100_rcu_usb2_reg_bits,
+	},
+	{
+		.compatible = "lantiq,xrx200-usb2-phy",
+		.data = &xrx200_rcu_usb2_reg_bits,
+	},
+	{
+		.compatible = "lantiq,xrx300-usb2-phy",
+		.data = &xrx200_rcu_usb2_reg_bits,
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, ltq_rcu_usb2_phy_of_match);
+
+static int ltq_rcu_usb2_phy_init(struct phy *phy)
+{
+	struct ltq_rcu_usb2_priv *priv = phy_get_drvdata(phy);
+
+	if (priv->reg_bits->have_ana_cfg) {
+		regmap_update_bits(priv->regmap, priv->ana_cfg1_reg_offset,
+			RCU_CFG1_TX_PEE, RCU_CFG1_TX_PEE);
+		regmap_update_bits(priv->regmap, priv->ana_cfg1_reg_offset,
+			RCU_CFG1_DIS_THR_MASK, 7 << RCU_CFG1_DIS_THR_SHIFT);
+	}
+
+	/* Configure core to host mode */
+	regmap_update_bits(priv->regmap, priv->phy_reg_offset,
+			   BIT(priv->reg_bits->hostmode), 0);
+
+	/* Select DMA endianness (Host-endian: big-endian) */
+	regmap_update_bits(priv->regmap, priv->phy_reg_offset,
+		BIT(priv->reg_bits->slave_endianness), 0);
+	regmap_update_bits(priv->regmap, priv->phy_reg_offset,
+		BIT(priv->reg_bits->host_endianness),
+		BIT(priv->reg_bits->host_endianness));
+
+	return 0;
+}
+
+static int ltq_rcu_usb2_phy_power_on(struct phy *phy)
+{
+	struct ltq_rcu_usb2_priv *priv = phy_get_drvdata(phy);
+	struct device *dev = priv->dev;
+	int ret;
+
+	reset_control_deassert(priv->phy_reset);
+
+	ret = clk_prepare_enable(priv->phy_gate_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable PHY gate\n");
+		return ret;
+	}
+
+	/*
+	 * at least the xrx200 usb2 phy requires some extra time to be
+	 * operational after enabling the clock
+	 */
+	usleep_range(100, 200);
+
+	return ret;
+}
+
+static int ltq_rcu_usb2_phy_power_off(struct phy *phy)
+{
+	struct ltq_rcu_usb2_priv *priv = phy_get_drvdata(phy);
+
+	reset_control_assert(priv->phy_reset);
+
+	clk_disable_unprepare(priv->phy_gate_clk);
+
+	return 0;
+}
+
+static const struct phy_ops ltq_rcu_usb2_phy_ops = {
+	.init		= ltq_rcu_usb2_phy_init,
+	.power_on	= ltq_rcu_usb2_phy_power_on,
+	.power_off	= ltq_rcu_usb2_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int ltq_rcu_usb2_of_parse(struct ltq_rcu_usb2_priv *priv,
+				 struct platform_device *pdev)
+{
+	struct device *dev = priv->dev;
+	const __be32 *offset;
+
+	priv->reg_bits = of_device_get_match_data(dev);
+
+	priv->regmap = syscon_node_to_regmap(dev->of_node->parent);
+	if (IS_ERR(priv->regmap)) {
+		dev_err(dev, "Failed to lookup RCU regmap\n");
+		return PTR_ERR(priv->regmap);
+	}
+
+	offset = of_get_address(dev->of_node, 0, NULL, NULL);
+	if (!offset) {
+		dev_err(dev, "Failed to get RCU PHY reg offset\n");
+		return -ENOENT;
+	}
+	priv->phy_reg_offset = __be32_to_cpu(*offset);
+
+	if (priv->reg_bits->have_ana_cfg) {
+		offset = of_get_address(dev->of_node, 1, NULL, NULL);
+		if (!offset) {
+			dev_err(dev, "Failed to get RCU ANA CFG1 reg offset\n");
+			return -ENOENT;
+		}
+		priv->ana_cfg1_reg_offset = __be32_to_cpu(*offset);
+	}
+
+	priv->phy_gate_clk = devm_clk_get(dev, "phy");
+	if (IS_ERR(priv->phy_gate_clk)) {
+		dev_err(dev, "Unable to get USB phy gate clk\n");
+		return PTR_ERR(priv->phy_gate_clk);
+	}
+
+	priv->ctrl_reset = devm_reset_control_get_shared(dev, "ctrl");
+	if (IS_ERR(priv->ctrl_reset)) {
+		if (PTR_ERR(priv->ctrl_reset) != -EPROBE_DEFER)
+			dev_err(dev, "failed to get 'ctrl' reset\n");
+		return PTR_ERR(priv->ctrl_reset);
+	}
+
+	priv->phy_reset = devm_reset_control_get_optional(dev, "phy");
+
+	return PTR_ERR_OR_ZERO(priv->phy_reset);
+}
+
+static int ltq_rcu_usb2_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct ltq_rcu_usb2_priv *priv;
+	struct phy_provider *provider;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = dev;
+
+	ret = ltq_rcu_usb2_of_parse(priv, pdev);
+	if (ret)
+		return ret;
+
+	/* Reset USB core through reset controller */
+	reset_control_deassert(priv->ctrl_reset);
+
+	reset_control_assert(priv->phy_reset);
+
+	priv->phy = devm_phy_create(dev, dev->of_node, &ltq_rcu_usb2_phy_ops);
+	if (IS_ERR(priv->phy)) {
+		dev_err(dev, "failed to create PHY\n");
+		return PTR_ERR(priv->phy);
+	}
+
+	phy_set_drvdata(priv->phy, priv);
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(provider))
+		return PTR_ERR(provider);
+
+	dev_set_drvdata(priv->dev, priv);
+	return 0;
+}
+
+static struct platform_driver ltq_rcu_usb2_phy_driver = {
+	.probe	= ltq_rcu_usb2_phy_probe,
+	.driver = {
+		.name	= "lantiq-rcu-usb2-phy",
+		.of_match_table	= ltq_rcu_usb2_phy_of_match,
+	}
+};
+module_platform_driver(ltq_rcu_usb2_phy_driver);
+
+MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
+MODULE_DESCRIPTION("Lantiq XWAY USB2 PHY driver");
+MODULE_LICENSE("GPL v2");

linux-7.2.3/drivers/phy/lantiq/phy-lantiq-vrx200-pcie.c

@@ -0,0 +1,493 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * PCIe PHY driver for Lantiq VRX200 and ARX300 SoCs.
+ *
+ * Copyright (C) 2019 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+ *
+ * Based on the BSP (called "UGW") driver:
+ *  Copyright (C) 2009-2015 Lei Chuanhua <chuanhua.lei@lantiq.com>
+ *  Copyright (C) 2016 Intel Corporation
+ *
+ * TODO: PHY modes other than 36MHz (without "SSC")
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <dt-bindings/phy/phy-lantiq-vrx200-pcie.h>
+
+#define PCIE_PHY_PLL_CTRL1				0x44
+
+#define PCIE_PHY_PLL_CTRL2				0x46
+#define PCIE_PHY_PLL_CTRL2_CONST_SDM_MASK		GENMASK(7, 0)
+#define PCIE_PHY_PLL_CTRL2_CONST_SDM_EN			BIT(8)
+#define PCIE_PHY_PLL_CTRL2_PLL_SDM_EN			BIT(9)
+
+#define PCIE_PHY_PLL_CTRL3				0x48
+#define PCIE_PHY_PLL_CTRL3_EXT_MMD_DIV_RATIO_EN		BIT(1)
+#define PCIE_PHY_PLL_CTRL3_EXT_MMD_DIV_RATIO_MASK	GENMASK(6, 4)
+
+#define PCIE_PHY_PLL_CTRL4				0x4a
+#define PCIE_PHY_PLL_CTRL5				0x4c
+#define PCIE_PHY_PLL_CTRL6				0x4e
+#define PCIE_PHY_PLL_CTRL7				0x50
+#define PCIE_PHY_PLL_A_CTRL1				0x52
+
+#define PCIE_PHY_PLL_A_CTRL2				0x54
+#define PCIE_PHY_PLL_A_CTRL2_LF_MODE_EN			BIT(14)
+
+#define PCIE_PHY_PLL_A_CTRL3				0x56
+#define PCIE_PHY_PLL_A_CTRL3_MMD_MASK			GENMASK(15, 13)
+
+#define PCIE_PHY_PLL_STATUS				0x58
+
+#define PCIE_PHY_TX1_CTRL1				0x60
+#define PCIE_PHY_TX1_CTRL1_FORCE_EN			BIT(3)
+#define PCIE_PHY_TX1_CTRL1_LOAD_EN			BIT(4)
+
+#define PCIE_PHY_TX1_CTRL2				0x62
+#define PCIE_PHY_TX1_CTRL3				0x64
+#define PCIE_PHY_TX1_A_CTRL1				0x66
+#define PCIE_PHY_TX1_A_CTRL2				0x68
+#define PCIE_PHY_TX1_MOD1				0x6a
+#define PCIE_PHY_TX1_MOD2				0x6c
+#define PCIE_PHY_TX1_MOD3				0x6e
+
+#define PCIE_PHY_TX2_CTRL1				0x70
+#define PCIE_PHY_TX2_CTRL1_LOAD_EN			BIT(4)
+
+#define PCIE_PHY_TX2_CTRL2				0x72
+#define PCIE_PHY_TX2_A_CTRL1				0x76
+#define PCIE_PHY_TX2_A_CTRL2				0x78
+#define PCIE_PHY_TX2_MOD1				0x7a
+#define PCIE_PHY_TX2_MOD2				0x7c
+#define PCIE_PHY_TX2_MOD3				0x7e
+
+#define PCIE_PHY_RX1_CTRL1				0xa0
+#define PCIE_PHY_RX1_CTRL1_LOAD_EN			BIT(1)
+
+#define PCIE_PHY_RX1_CTRL2				0xa2
+#define PCIE_PHY_RX1_CDR				0xa4
+#define PCIE_PHY_RX1_EI					0xa6
+#define PCIE_PHY_RX1_A_CTRL				0xaa
+
+struct ltq_vrx200_pcie_phy_priv {
+	struct phy			*phy;
+	unsigned int			mode;
+	struct device			*dev;
+	struct regmap			*phy_regmap;
+	struct regmap			*rcu_regmap;
+	struct clk			*pdi_clk;
+	struct clk			*phy_clk;
+	struct reset_control		*phy_reset;
+	struct reset_control		*pcie_reset;
+	u32				rcu_ahb_endian_offset;
+	u32				rcu_ahb_endian_big_endian_mask;
+};
+
+static void ltq_vrx200_pcie_phy_common_setup(struct phy *phy)
+{
+	struct ltq_vrx200_pcie_phy_priv *priv = phy_get_drvdata(phy);
+
+	/* PLL Setting */
+	regmap_write(priv->phy_regmap, PCIE_PHY_PLL_A_CTRL1, 0x120e);
+
+	/* increase the bias reference voltage */
+	regmap_write(priv->phy_regmap, PCIE_PHY_PLL_A_CTRL2, 0x39d7);
+	regmap_write(priv->phy_regmap, PCIE_PHY_PLL_A_CTRL3, 0x0900);
+
+	/* Endcnt */
+	regmap_write(priv->phy_regmap, PCIE_PHY_RX1_EI, 0x0004);
+	regmap_write(priv->phy_regmap, PCIE_PHY_RX1_A_CTRL, 0x6803);
+
+	regmap_update_bits(priv->phy_regmap, PCIE_PHY_TX1_CTRL1,
+			   PCIE_PHY_TX1_CTRL1_FORCE_EN,
+			   PCIE_PHY_TX1_CTRL1_FORCE_EN);
+
+	/* predrv_ser_en */
+	regmap_write(priv->phy_regmap, PCIE_PHY_TX1_A_CTRL2, 0x0706);
+
+	/* ctrl_lim */
+	regmap_write(priv->phy_regmap, PCIE_PHY_TX1_CTRL3, 0x1fff);
+
+	/* ctrl */
+	regmap_write(priv->phy_regmap, PCIE_PHY_TX1_A_CTRL1, 0x0810);
+
+	/* predrv_ser_en */
+	regmap_update_bits(priv->phy_regmap, PCIE_PHY_TX2_A_CTRL2, 0x7f00,
+			   0x4700);
+
+	/* RTERM */
+	regmap_write(priv->phy_regmap, PCIE_PHY_TX1_CTRL2, 0x2e00);
+
+	/* Improved 100MHz clock output  */
+	regmap_write(priv->phy_regmap, PCIE_PHY_TX2_CTRL2, 0x3096);
+	regmap_write(priv->phy_regmap, PCIE_PHY_TX2_A_CTRL2, 0x4707);
+
+	/* Reduced CDR BW to avoid glitches */
+	regmap_write(priv->phy_regmap, PCIE_PHY_RX1_CDR, 0x0235);
+}
+
+static void pcie_phy_36mhz_mode_setup(struct phy *phy)
+{
+	struct ltq_vrx200_pcie_phy_priv *priv = phy_get_drvdata(phy);
+
+	regmap_update_bits(priv->phy_regmap, PCIE_PHY_PLL_CTRL3,
+			   PCIE_PHY_PLL_CTRL3_EXT_MMD_DIV_RATIO_EN, 0x0000);
+
+	regmap_update_bits(priv->phy_regmap, PCIE_PHY_PLL_CTRL3,
+			   PCIE_PHY_PLL_CTRL3_EXT_MMD_DIV_RATIO_MASK, 0x0000);
+
+	regmap_update_bits(priv->phy_regmap, PCIE_PHY_PLL_CTRL2,
+			   PCIE_PHY_PLL_CTRL2_PLL_SDM_EN,
+			   PCIE_PHY_PLL_CTRL2_PLL_SDM_EN);
+
+	regmap_update_bits(priv->phy_regmap, PCIE_PHY_PLL_CTRL2,
+			   PCIE_PHY_PLL_CTRL2_CONST_SDM_EN,
+			   PCIE_PHY_PLL_CTRL2_CONST_SDM_EN);
+
+	regmap_update_bits(priv->phy_regmap, PCIE_PHY_PLL_A_CTRL3,
+			   PCIE_PHY_PLL_A_CTRL3_MMD_MASK,
+			   FIELD_PREP(PCIE_PHY_PLL_A_CTRL3_MMD_MASK, 0x1));
+
+	regmap_update_bits(priv->phy_regmap, PCIE_PHY_PLL_A_CTRL2,
+			   PCIE_PHY_PLL_A_CTRL2_LF_MODE_EN, 0x0000);
+
+	/* const_sdm */
+	regmap_write(priv->phy_regmap, PCIE_PHY_PLL_CTRL1, 0x38e4);
+
+	regmap_update_bits(priv->phy_regmap, PCIE_PHY_PLL_CTRL2,
+			   PCIE_PHY_PLL_CTRL2_CONST_SDM_MASK,
+			   FIELD_PREP(PCIE_PHY_PLL_CTRL2_CONST_SDM_MASK,
+				      0xee));
+
+	/* pllmod */
+	regmap_write(priv->phy_regmap, PCIE_PHY_PLL_CTRL7, 0x0002);
+	regmap_write(priv->phy_regmap, PCIE_PHY_PLL_CTRL6, 0x3a04);
+	regmap_write(priv->phy_regmap, PCIE_PHY_PLL_CTRL5, 0xfae3);
+	regmap_write(priv->phy_regmap, PCIE_PHY_PLL_CTRL4, 0x1b72);
+}
+
+static int ltq_vrx200_pcie_phy_wait_for_pll(struct phy *phy)
+{
+	struct ltq_vrx200_pcie_phy_priv *priv = phy_get_drvdata(phy);
+	unsigned int tmp;
+	int ret;
+
+	ret = regmap_read_poll_timeout(priv->phy_regmap, PCIE_PHY_PLL_STATUS,
+				       tmp, ((tmp & 0x0070) == 0x0070), 10,
+				       10000);
+	if (ret) {
+		dev_err(priv->dev, "PLL Link timeout, PLL status = 0x%04x\n",
+			tmp);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void ltq_vrx200_pcie_phy_apply_workarounds(struct phy *phy)
+{
+	struct ltq_vrx200_pcie_phy_priv *priv = phy_get_drvdata(phy);
+	static const struct reg_default slices[] =  {
+		{
+			.reg = PCIE_PHY_TX1_CTRL1,
+			.def = PCIE_PHY_TX1_CTRL1_LOAD_EN,
+		},
+		{
+			.reg = PCIE_PHY_TX2_CTRL1,
+			.def = PCIE_PHY_TX2_CTRL1_LOAD_EN,
+		},
+		{
+			.reg = PCIE_PHY_RX1_CTRL1,
+			.def = PCIE_PHY_RX1_CTRL1_LOAD_EN,
+		}
+	};
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(slices); i++) {
+		/* enable load_en */
+		regmap_update_bits(priv->phy_regmap, slices[i].reg,
+				   slices[i].def, slices[i].def);
+
+		udelay(1);
+
+		/* disable load_en */
+		regmap_update_bits(priv->phy_regmap, slices[i].reg,
+				   slices[i].def, 0x0);
+	}
+
+	for (i = 0; i < 5; i++) {
+		/* TX2 modulation */
+		regmap_write(priv->phy_regmap, PCIE_PHY_TX2_MOD1, 0x1ffe);
+		regmap_write(priv->phy_regmap, PCIE_PHY_TX2_MOD2, 0xfffe);
+		regmap_write(priv->phy_regmap, PCIE_PHY_TX2_MOD3, 0x0601);
+		usleep_range(1000, 2000);
+		regmap_write(priv->phy_regmap, PCIE_PHY_TX2_MOD3, 0x0001);
+
+		/* TX1 modulation */
+		regmap_write(priv->phy_regmap, PCIE_PHY_TX1_MOD1, 0x1ffe);
+		regmap_write(priv->phy_regmap, PCIE_PHY_TX1_MOD2, 0xfffe);
+		regmap_write(priv->phy_regmap, PCIE_PHY_TX1_MOD3, 0x0601);
+		usleep_range(1000, 2000);
+		regmap_write(priv->phy_regmap, PCIE_PHY_TX1_MOD3, 0x0001);
+	}
+}
+
+static int ltq_vrx200_pcie_phy_init(struct phy *phy)
+{
+	struct ltq_vrx200_pcie_phy_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	if (of_device_is_big_endian(priv->dev->of_node))
+		regmap_update_bits(priv->rcu_regmap,
+				   priv->rcu_ahb_endian_offset,
+				   priv->rcu_ahb_endian_big_endian_mask,
+				   priv->rcu_ahb_endian_big_endian_mask);
+	else
+		regmap_update_bits(priv->rcu_regmap,
+				   priv->rcu_ahb_endian_offset,
+				   priv->rcu_ahb_endian_big_endian_mask, 0x0);
+
+	ret = reset_control_assert(priv->phy_reset);
+	if (ret)
+		goto err;
+
+	udelay(1);
+
+	ret = reset_control_deassert(priv->phy_reset);
+	if (ret)
+		goto err;
+
+	udelay(1);
+
+	ret = reset_control_deassert(priv->pcie_reset);
+	if (ret)
+		goto err_assert_phy_reset;
+
+	/* Make sure PHY PLL is stable */
+	usleep_range(20, 40);
+
+	return 0;
+
+err_assert_phy_reset:
+	reset_control_assert(priv->phy_reset);
+err:
+	return ret;
+}
+
+static int ltq_vrx200_pcie_phy_exit(struct phy *phy)
+{
+	struct ltq_vrx200_pcie_phy_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	ret = reset_control_assert(priv->pcie_reset);
+	if (ret)
+		return ret;
+
+	ret = reset_control_assert(priv->phy_reset);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int ltq_vrx200_pcie_phy_power_on(struct phy *phy)
+{
+	struct ltq_vrx200_pcie_phy_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	/* Enable PDI to access PCIe PHY register */
+	ret = clk_prepare_enable(priv->pdi_clk);
+	if (ret)
+		goto err;
+
+	/* Configure PLL and PHY clock */
+	ltq_vrx200_pcie_phy_common_setup(phy);
+
+	pcie_phy_36mhz_mode_setup(phy);
+
+	/* Enable the PCIe PHY and make PLL setting take effect */
+	ret = clk_prepare_enable(priv->phy_clk);
+	if (ret)
+		goto err_disable_pdi_clk;
+
+	/* Check if we are in "startup ready" status */
+	ret = ltq_vrx200_pcie_phy_wait_for_pll(phy);
+	if (ret)
+		goto err_disable_phy_clk;
+
+	ltq_vrx200_pcie_phy_apply_workarounds(phy);
+
+	return 0;
+
+err_disable_phy_clk:
+	clk_disable_unprepare(priv->phy_clk);
+err_disable_pdi_clk:
+	clk_disable_unprepare(priv->pdi_clk);
+err:
+	return ret;
+}
+
+static int ltq_vrx200_pcie_phy_power_off(struct phy *phy)
+{
+	struct ltq_vrx200_pcie_phy_priv *priv = phy_get_drvdata(phy);
+
+	clk_disable_unprepare(priv->phy_clk);
+	clk_disable_unprepare(priv->pdi_clk);
+
+	return 0;
+}
+
+static const struct phy_ops ltq_vrx200_pcie_phy_ops = {
+	.init		= ltq_vrx200_pcie_phy_init,
+	.exit		= ltq_vrx200_pcie_phy_exit,
+	.power_on	= ltq_vrx200_pcie_phy_power_on,
+	.power_off	= ltq_vrx200_pcie_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static struct phy *ltq_vrx200_pcie_phy_xlate(struct device *dev,
+					     const struct of_phandle_args *args)
+{
+	struct ltq_vrx200_pcie_phy_priv *priv = dev_get_drvdata(dev);
+	unsigned int mode;
+
+	if (args->args_count != 1) {
+		dev_err(dev, "invalid number of arguments\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	mode = args->args[0];
+
+	switch (mode) {
+	case LANTIQ_PCIE_PHY_MODE_36MHZ:
+		priv->mode = mode;
+		break;
+
+	case LANTIQ_PCIE_PHY_MODE_25MHZ:
+	case LANTIQ_PCIE_PHY_MODE_25MHZ_SSC:
+	case LANTIQ_PCIE_PHY_MODE_36MHZ_SSC:
+	case LANTIQ_PCIE_PHY_MODE_100MHZ:
+	case LANTIQ_PCIE_PHY_MODE_100MHZ_SSC:
+		dev_err(dev, "PHY mode not implemented yet: %u\n", mode);
+		return ERR_PTR(-EINVAL);
+
+	default:
+		dev_err(dev, "invalid PHY mode %u\n", mode);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return priv->phy;
+}
+
+static int ltq_vrx200_pcie_phy_probe(struct platform_device *pdev)
+{
+	static const struct regmap_config regmap_config = {
+		.reg_bits = 8,
+		.val_bits = 16,
+		.reg_stride = 2,
+		.max_register = PCIE_PHY_RX1_A_CTRL,
+	};
+	struct ltq_vrx200_pcie_phy_priv *priv;
+	struct device *dev = &pdev->dev;
+	struct phy_provider *provider;
+	void __iomem *base;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	priv->phy_regmap = devm_regmap_init_mmio(dev, base, &regmap_config);
+	if (IS_ERR(priv->phy_regmap))
+		return PTR_ERR(priv->phy_regmap);
+
+	priv->rcu_regmap = syscon_regmap_lookup_by_phandle(dev->of_node,
+							   "lantiq,rcu");
+	if (IS_ERR(priv->rcu_regmap))
+		return PTR_ERR(priv->rcu_regmap);
+
+	ret = device_property_read_u32(dev, "lantiq,rcu-endian-offset",
+				       &priv->rcu_ahb_endian_offset);
+	if (ret) {
+		dev_err(dev,
+			"failed to parse the 'lantiq,rcu-endian-offset' property\n");
+		return ret;
+	}
+
+	ret = device_property_read_u32(dev, "lantiq,rcu-big-endian-mask",
+				       &priv->rcu_ahb_endian_big_endian_mask);
+	if (ret) {
+		dev_err(dev,
+			"failed to parse the 'lantiq,rcu-big-endian-mask' property\n");
+		return ret;
+	}
+
+	priv->pdi_clk = devm_clk_get(dev, "pdi");
+	if (IS_ERR(priv->pdi_clk))
+		return PTR_ERR(priv->pdi_clk);
+
+	priv->phy_clk = devm_clk_get(dev, "phy");
+	if (IS_ERR(priv->phy_clk))
+		return PTR_ERR(priv->phy_clk);
+
+	priv->phy_reset = devm_reset_control_get_exclusive(dev, "phy");
+	if (IS_ERR(priv->phy_reset))
+		return PTR_ERR(priv->phy_reset);
+
+	priv->pcie_reset = devm_reset_control_get_shared(dev, "pcie");
+	if (IS_ERR(priv->pcie_reset))
+		return PTR_ERR(priv->pcie_reset);
+
+	priv->dev = dev;
+
+	priv->phy = devm_phy_create(dev, dev->of_node,
+				    &ltq_vrx200_pcie_phy_ops);
+	if (IS_ERR(priv->phy)) {
+		dev_err(dev, "failed to create PHY\n");
+		return PTR_ERR(priv->phy);
+	}
+
+	phy_set_drvdata(priv->phy, priv);
+	dev_set_drvdata(dev, priv);
+
+	provider = devm_of_phy_provider_register(dev,
+						 ltq_vrx200_pcie_phy_xlate);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id ltq_vrx200_pcie_phy_of_match[] = {
+	{ .compatible = "lantiq,vrx200-pcie-phy", },
+	{ .compatible = "lantiq,arx300-pcie-phy", },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, ltq_vrx200_pcie_phy_of_match);
+
+static struct platform_driver ltq_vrx200_pcie_phy_driver = {
+	.probe	= ltq_vrx200_pcie_phy_probe,
+	.driver = {
+		.name	= "ltq-vrx200-pcie-phy",
+		.of_match_table	= ltq_vrx200_pcie_phy_of_match,
+	}
+};
+module_platform_driver(ltq_vrx200_pcie_phy_driver);
+
+MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
+MODULE_DESCRIPTION("Lantiq VRX200 and ARX300 PCIe PHY driver");
+MODULE_LICENSE("GPL v2");