Resguardo inicial

linux-7.2.3/drivers/phy/st/Kconfig

@@ -0,0 +1,60 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Phy drivers for STMicro platforms
+#
+config PHY_MIPHY28LP
+	tristate "STMicroelectronics MIPHY28LP PHY driver for STiH407"
+	depends on ARCH_STI || COMPILE_TEST
+	select GENERIC_PHY
+	help
+	  Enable this to support the miphy transceiver (for SATA/PCIE/USB3)
+	  that is part of STMicroelectronics STiH407 SoC.
+
+config PHY_ST_SPEAR1310_MIPHY
+	tristate "ST SPEAR1310-MIPHY driver"
+	select GENERIC_PHY
+	depends on MACH_SPEAR1310 || COMPILE_TEST
+	help
+	  Support for ST SPEAr1310 MIPHY which can be used for PCIe and SATA.
+
+config PHY_ST_SPEAR1340_MIPHY
+	tristate "ST SPEAR1340-MIPHY driver"
+	select GENERIC_PHY
+	depends on MACH_SPEAR1340 || COMPILE_TEST
+	help
+	  Support for ST SPEAr1340 MIPHY which can be used for PCIe and SATA.
+
+config PHY_STIH407_USB
+	tristate "STMicroelectronics USB2 picoPHY driver for STiH407 family"
+	depends on RESET_CONTROLLER
+	depends on ARCH_STI || COMPILE_TEST
+	select GENERIC_PHY
+	help
+	  Enable this support to enable the picoPHY device used by USB2
+	  and USB3 controllers on STMicroelectronics STiH407 SoC families.
+
+config PHY_STM32_COMBOPHY
+	tristate "STMicroelectronics COMBOPHY driver for STM32MP25"
+	depends on ARCH_STM32 || COMPILE_TEST
+	select GENERIC_PHY
+	help
+	  Enable this to support the COMBOPHY device used by USB3 or PCIe
+	  controllers on STMicroelectronics STM32MP25 SoC.
+	  This driver controls the COMBOPHY block to generate the PCIe 100Mhz
+	  reference clock from either the external clock generator or HSE
+	  internal SoC clock source.
+
+config PHY_STM32_USBPHYC
+	tristate "STMicroelectronics STM32 USB HS PHY Controller driver"
+	depends on ARCH_STM32 || COMPILE_TEST
+	depends on COMMON_CLK
+	select GENERIC_PHY
+	help
+	  Enable this to support the High-Speed USB transceivers that are part
+	  of some STMicroelectronics STM32 SoCs.
+
+	  This driver controls the entire USB PHY block: the USB PHY controller
+	  (USBPHYC) and the two 8-bit wide UTMI+ interfaces. First interface is
+	  used by an HS USB Host controller, and the second one is shared
+	  between an HS USB OTG controller and an HS USB Host controller,
+	  selected by a USB switch.

linux-7.2.3/drivers/phy/st/Makefile

@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_PHY_MIPHY28LP) 		+= phy-miphy28lp.o
+obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
+obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o
+obj-$(CONFIG_PHY_STIH407_USB)		+= phy-stih407-usb.o
+obj-$(CONFIG_PHY_STM32_COMBOPHY)	+= phy-stm32-combophy.o
+obj-$(CONFIG_PHY_STM32_USBPHYC) 	+= phy-stm32-usbphyc.o

linux-7.2.3/drivers/phy/st/phy-spear1310-miphy.c

@@ -0,0 +1,258 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * ST SPEAr1310-miphy driver
+ *
+ * Copyright (C) 2014 ST Microelectronics
+ * Pratyush Anand <pratyush.anand@gmail.com>
+ * Mohit Kumar <mohit.kumar.dhaka@gmail.com>
+ */
+
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* SPEAr1310 Registers */
+#define SPEAR1310_PCIE_SATA_CFG			0x3A4
+	#define SPEAR1310_PCIE_SATA2_SEL_PCIE		(0 << 31)
+	#define SPEAR1310_PCIE_SATA1_SEL_PCIE		(0 << 30)
+	#define SPEAR1310_PCIE_SATA0_SEL_PCIE		(0 << 29)
+	#define SPEAR1310_PCIE_SATA2_SEL_SATA		BIT(31)
+	#define SPEAR1310_PCIE_SATA1_SEL_SATA		BIT(30)
+	#define SPEAR1310_PCIE_SATA0_SEL_SATA		BIT(29)
+	#define SPEAR1310_SATA2_CFG_TX_CLK_EN		BIT(27)
+	#define SPEAR1310_SATA2_CFG_RX_CLK_EN		BIT(26)
+	#define SPEAR1310_SATA2_CFG_POWERUP_RESET	BIT(25)
+	#define SPEAR1310_SATA2_CFG_PM_CLK_EN		BIT(24)
+	#define SPEAR1310_SATA1_CFG_TX_CLK_EN		BIT(23)
+	#define SPEAR1310_SATA1_CFG_RX_CLK_EN		BIT(22)
+	#define SPEAR1310_SATA1_CFG_POWERUP_RESET	BIT(21)
+	#define SPEAR1310_SATA1_CFG_PM_CLK_EN		BIT(20)
+	#define SPEAR1310_SATA0_CFG_TX_CLK_EN		BIT(19)
+	#define SPEAR1310_SATA0_CFG_RX_CLK_EN		BIT(18)
+	#define SPEAR1310_SATA0_CFG_POWERUP_RESET	BIT(17)
+	#define SPEAR1310_SATA0_CFG_PM_CLK_EN		BIT(16)
+	#define SPEAR1310_PCIE2_CFG_DEVICE_PRESENT	BIT(11)
+	#define SPEAR1310_PCIE2_CFG_POWERUP_RESET	BIT(10)
+	#define SPEAR1310_PCIE2_CFG_CORE_CLK_EN		BIT(9)
+	#define SPEAR1310_PCIE2_CFG_AUX_CLK_EN		BIT(8)
+	#define SPEAR1310_PCIE1_CFG_DEVICE_PRESENT	BIT(7)
+	#define SPEAR1310_PCIE1_CFG_POWERUP_RESET	BIT(6)
+	#define SPEAR1310_PCIE1_CFG_CORE_CLK_EN		BIT(5)
+	#define SPEAR1310_PCIE1_CFG_AUX_CLK_EN		BIT(4)
+	#define SPEAR1310_PCIE0_CFG_DEVICE_PRESENT	BIT(3)
+	#define SPEAR1310_PCIE0_CFG_POWERUP_RESET	BIT(2)
+	#define SPEAR1310_PCIE0_CFG_CORE_CLK_EN		BIT(1)
+	#define SPEAR1310_PCIE0_CFG_AUX_CLK_EN		BIT(0)
+
+	#define SPEAR1310_PCIE_CFG_MASK(x) ((0xF << (x * 4)) | BIT((x + 29)))
+	#define SPEAR1310_SATA_CFG_MASK(x) ((0xF << (x * 4 + 16)) | \
+			BIT((x + 29)))
+	#define SPEAR1310_PCIE_CFG_VAL(x) \
+			(SPEAR1310_PCIE_SATA##x##_SEL_PCIE | \
+			SPEAR1310_PCIE##x##_CFG_AUX_CLK_EN | \
+			SPEAR1310_PCIE##x##_CFG_CORE_CLK_EN | \
+			SPEAR1310_PCIE##x##_CFG_POWERUP_RESET | \
+			SPEAR1310_PCIE##x##_CFG_DEVICE_PRESENT)
+	#define SPEAR1310_SATA_CFG_VAL(x) \
+			(SPEAR1310_PCIE_SATA##x##_SEL_SATA | \
+			SPEAR1310_SATA##x##_CFG_PM_CLK_EN | \
+			SPEAR1310_SATA##x##_CFG_POWERUP_RESET | \
+			SPEAR1310_SATA##x##_CFG_RX_CLK_EN | \
+			SPEAR1310_SATA##x##_CFG_TX_CLK_EN)
+
+#define SPEAR1310_PCIE_MIPHY_CFG_1		0x3A8
+	#define SPEAR1310_MIPHY_DUAL_OSC_BYPASS_EXT	BIT(31)
+	#define SPEAR1310_MIPHY_DUAL_CLK_REF_DIV2	BIT(28)
+	#define SPEAR1310_MIPHY_DUAL_PLL_RATIO_TOP(x)	(x << 16)
+	#define SPEAR1310_MIPHY_SINGLE_OSC_BYPASS_EXT	BIT(15)
+	#define SPEAR1310_MIPHY_SINGLE_CLK_REF_DIV2	BIT(12)
+	#define SPEAR1310_MIPHY_SINGLE_PLL_RATIO_TOP(x)	(x << 0)
+	#define SPEAR1310_PCIE_SATA_MIPHY_CFG_SATA_MASK (0xFFFF)
+	#define SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE_MASK (0xFFFF << 16)
+	#define SPEAR1310_PCIE_SATA_MIPHY_CFG_SATA \
+			(SPEAR1310_MIPHY_DUAL_OSC_BYPASS_EXT | \
+			SPEAR1310_MIPHY_DUAL_CLK_REF_DIV2 | \
+			SPEAR1310_MIPHY_DUAL_PLL_RATIO_TOP(60) | \
+			SPEAR1310_MIPHY_SINGLE_OSC_BYPASS_EXT | \
+			SPEAR1310_MIPHY_SINGLE_CLK_REF_DIV2 | \
+			SPEAR1310_MIPHY_SINGLE_PLL_RATIO_TOP(60))
+	#define SPEAR1310_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \
+			(SPEAR1310_MIPHY_SINGLE_PLL_RATIO_TOP(120))
+	#define SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE \
+			(SPEAR1310_MIPHY_DUAL_OSC_BYPASS_EXT | \
+			SPEAR1310_MIPHY_DUAL_PLL_RATIO_TOP(25) | \
+			SPEAR1310_MIPHY_SINGLE_OSC_BYPASS_EXT | \
+			SPEAR1310_MIPHY_SINGLE_PLL_RATIO_TOP(25))
+
+#define SPEAR1310_PCIE_MIPHY_CFG_2		0x3AC
+
+enum spear1310_miphy_mode {
+	SATA,
+	PCIE,
+};
+
+struct spear1310_miphy_priv {
+	/* instance id of this phy */
+	u32				id;
+	/* phy mode: 0 for SATA 1 for PCIe */
+	enum spear1310_miphy_mode	mode;
+	/* regmap for any soc specific misc registers */
+	struct regmap			*misc;
+	/* phy struct pointer */
+	struct phy			*phy;
+};
+
+static int spear1310_miphy_pcie_init(struct spear1310_miphy_priv *priv)
+{
+	u32 val;
+
+	regmap_update_bits(priv->misc, SPEAR1310_PCIE_MIPHY_CFG_1,
+			   SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE_MASK,
+			   SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE);
+
+	switch (priv->id) {
+	case 0:
+		val = SPEAR1310_PCIE_CFG_VAL(0);
+		break;
+	case 1:
+		val = SPEAR1310_PCIE_CFG_VAL(1);
+		break;
+	case 2:
+		val = SPEAR1310_PCIE_CFG_VAL(2);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	regmap_update_bits(priv->misc, SPEAR1310_PCIE_SATA_CFG,
+			   SPEAR1310_PCIE_CFG_MASK(priv->id), val);
+
+	return 0;
+}
+
+static int spear1310_miphy_pcie_exit(struct spear1310_miphy_priv *priv)
+{
+	regmap_update_bits(priv->misc, SPEAR1310_PCIE_SATA_CFG,
+			   SPEAR1310_PCIE_CFG_MASK(priv->id), 0);
+
+	regmap_update_bits(priv->misc, SPEAR1310_PCIE_MIPHY_CFG_1,
+			   SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE_MASK, 0);
+
+	return 0;
+}
+
+static int spear1310_miphy_init(struct phy *phy)
+{
+	struct spear1310_miphy_priv *priv = phy_get_drvdata(phy);
+	int ret = 0;
+
+	if (priv->mode == PCIE)
+		ret = spear1310_miphy_pcie_init(priv);
+
+	return ret;
+}
+
+static int spear1310_miphy_exit(struct phy *phy)
+{
+	struct spear1310_miphy_priv *priv = phy_get_drvdata(phy);
+	int ret = 0;
+
+	if (priv->mode == PCIE)
+		ret = spear1310_miphy_pcie_exit(priv);
+
+	return ret;
+}
+
+static const struct of_device_id spear1310_miphy_of_match[] = {
+	{ .compatible = "st,spear1310-miphy" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, spear1310_miphy_of_match);
+
+static const struct phy_ops spear1310_miphy_ops = {
+	.init = spear1310_miphy_init,
+	.exit = spear1310_miphy_exit,
+	.owner = THIS_MODULE,
+};
+
+static struct phy *spear1310_miphy_xlate(struct device *dev,
+					 const struct of_phandle_args *args)
+{
+	struct spear1310_miphy_priv *priv = dev_get_drvdata(dev);
+
+	if (args->args_count < 1) {
+		dev_err(dev, "DT did not pass correct no of args\n");
+		return ERR_PTR(-ENODEV);
+	}
+
+	priv->mode = args->args[0];
+
+	if (priv->mode != SATA && priv->mode != PCIE) {
+		dev_err(dev, "DT did not pass correct phy mode\n");
+		return ERR_PTR(-ENODEV);
+	}
+
+	return priv->phy;
+}
+
+static int spear1310_miphy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct spear1310_miphy_priv *priv;
+	struct phy_provider *phy_provider;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->misc =
+		syscon_regmap_lookup_by_phandle(dev->of_node, "misc");
+	if (IS_ERR(priv->misc)) {
+		dev_err(dev, "failed to find misc regmap\n");
+		return PTR_ERR(priv->misc);
+	}
+
+	if (of_property_read_u32(dev->of_node, "phy-id", &priv->id)) {
+		dev_err(dev, "failed to find phy id\n");
+		return -EINVAL;
+	}
+
+	priv->phy = devm_phy_create(dev, NULL, &spear1310_miphy_ops);
+	if (IS_ERR(priv->phy)) {
+		dev_err(dev, "failed to create SATA PCIe PHY\n");
+		return PTR_ERR(priv->phy);
+	}
+
+	dev_set_drvdata(dev, priv);
+	phy_set_drvdata(priv->phy, priv);
+
+	phy_provider =
+		devm_of_phy_provider_register(dev, spear1310_miphy_xlate);
+	if (IS_ERR(phy_provider)) {
+		dev_err(dev, "failed to register phy provider\n");
+		return PTR_ERR(phy_provider);
+	}
+
+	return 0;
+}
+
+static struct platform_driver spear1310_miphy_driver = {
+	.probe		= spear1310_miphy_probe,
+	.driver = {
+		.name = "spear1310-miphy",
+		.of_match_table = spear1310_miphy_of_match,
+	},
+};
+
+module_platform_driver(spear1310_miphy_driver);
+
+MODULE_DESCRIPTION("ST SPEAR1310-MIPHY driver");
+MODULE_AUTHOR("Pratyush Anand <pratyush.anand@gmail.com>");
+MODULE_LICENSE("GPL v2");

linux-7.2.3/drivers/phy/st/phy-spear1340-miphy.c

@@ -0,0 +1,291 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * ST spear1340-miphy driver
+ *
+ * Copyright (C) 2014 ST Microelectronics
+ * Pratyush Anand <pratyush.anand@gmail.com>
+ * Mohit Kumar <mohit.kumar.dhaka@gmail.com>
+ */
+
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* SPEAr1340 Registers */
+/* Power Management Registers */
+#define SPEAR1340_PCM_CFG			0x100
+	#define SPEAR1340_PCM_CFG_SATA_POWER_EN		BIT(11)
+#define SPEAR1340_PCM_WKUP_CFG			0x104
+#define SPEAR1340_SWITCH_CTR			0x108
+
+#define SPEAR1340_PERIP1_SW_RST			0x318
+	#define SPEAR1340_PERIP1_SW_RSATA		BIT(12)
+#define SPEAR1340_PERIP2_SW_RST			0x31C
+#define SPEAR1340_PERIP3_SW_RST			0x320
+
+/* PCIE - SATA configuration registers */
+#define SPEAR1340_PCIE_SATA_CFG			0x424
+	/* PCIE CFG MASks */
+	#define SPEAR1340_PCIE_CFG_DEVICE_PRESENT	BIT(11)
+	#define SPEAR1340_PCIE_CFG_POWERUP_RESET	BIT(10)
+	#define SPEAR1340_PCIE_CFG_CORE_CLK_EN		BIT(9)
+	#define SPEAR1340_PCIE_CFG_AUX_CLK_EN		BIT(8)
+	#define SPEAR1340_SATA_CFG_TX_CLK_EN		BIT(4)
+	#define SPEAR1340_SATA_CFG_RX_CLK_EN		BIT(3)
+	#define SPEAR1340_SATA_CFG_POWERUP_RESET	BIT(2)
+	#define SPEAR1340_SATA_CFG_PM_CLK_EN		BIT(1)
+	#define SPEAR1340_PCIE_SATA_SEL_PCIE		(0)
+	#define SPEAR1340_PCIE_SATA_SEL_SATA		(1)
+	#define SPEAR1340_PCIE_SATA_CFG_MASK		0xF1F
+	#define SPEAR1340_PCIE_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_PCIE | \
+			SPEAR1340_PCIE_CFG_AUX_CLK_EN | \
+			SPEAR1340_PCIE_CFG_CORE_CLK_EN | \
+			SPEAR1340_PCIE_CFG_POWERUP_RESET | \
+			SPEAR1340_PCIE_CFG_DEVICE_PRESENT)
+	#define SPEAR1340_SATA_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_SATA | \
+			SPEAR1340_SATA_CFG_PM_CLK_EN | \
+			SPEAR1340_SATA_CFG_POWERUP_RESET | \
+			SPEAR1340_SATA_CFG_RX_CLK_EN | \
+			SPEAR1340_SATA_CFG_TX_CLK_EN)
+
+#define SPEAR1340_PCIE_MIPHY_CFG		0x428
+	#define SPEAR1340_MIPHY_OSC_BYPASS_EXT		BIT(31)
+	#define SPEAR1340_MIPHY_CLK_REF_DIV2		BIT(27)
+	#define SPEAR1340_MIPHY_CLK_REF_DIV4		(2 << 27)
+	#define SPEAR1340_MIPHY_CLK_REF_DIV8		(3 << 27)
+	#define SPEAR1340_MIPHY_PLL_RATIO_TOP(x)	(x << 0)
+	#define SPEAR1340_PCIE_MIPHY_CFG_MASK		0xF80000FF
+	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA \
+			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
+			SPEAR1340_MIPHY_CLK_REF_DIV2 | \
+			SPEAR1340_MIPHY_PLL_RATIO_TOP(60))
+	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \
+			(SPEAR1340_MIPHY_PLL_RATIO_TOP(120))
+	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE \
+			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
+			SPEAR1340_MIPHY_PLL_RATIO_TOP(25))
+
+enum spear1340_miphy_mode {
+	SATA,
+	PCIE,
+};
+
+struct spear1340_miphy_priv {
+	/* phy mode: 0 for SATA 1 for PCIe */
+	enum spear1340_miphy_mode	mode;
+	/* regmap for any soc specific misc registers */
+	struct regmap			*misc;
+	/* phy struct pointer */
+	struct phy			*phy;
+};
+
+static int spear1340_miphy_sata_init(struct spear1340_miphy_priv *priv)
+{
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_SATA_CFG,
+			   SPEAR1340_PCIE_SATA_CFG_MASK,
+			   SPEAR1340_SATA_CFG_VAL);
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_MIPHY_CFG,
+			   SPEAR1340_PCIE_MIPHY_CFG_MASK,
+			   SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK);
+	/* Switch on sata power domain */
+	regmap_update_bits(priv->misc, SPEAR1340_PCM_CFG,
+			   SPEAR1340_PCM_CFG_SATA_POWER_EN,
+			   SPEAR1340_PCM_CFG_SATA_POWER_EN);
+	/* Wait for SATA power domain on */
+	msleep(20);
+
+	/* Disable PCIE SATA Controller reset */
+	regmap_update_bits(priv->misc, SPEAR1340_PERIP1_SW_RST,
+			   SPEAR1340_PERIP1_SW_RSATA, 0);
+	/* Wait for SATA reset de-assert completion */
+	msleep(20);
+
+	return 0;
+}
+
+static int spear1340_miphy_sata_exit(struct spear1340_miphy_priv *priv)
+{
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_SATA_CFG,
+			   SPEAR1340_PCIE_SATA_CFG_MASK, 0);
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_MIPHY_CFG,
+			   SPEAR1340_PCIE_MIPHY_CFG_MASK, 0);
+
+	/* Enable PCIE SATA Controller reset */
+	regmap_update_bits(priv->misc, SPEAR1340_PERIP1_SW_RST,
+			   SPEAR1340_PERIP1_SW_RSATA,
+			   SPEAR1340_PERIP1_SW_RSATA);
+	/* Wait for SATA power domain off */
+	msleep(20);
+	/* Switch off sata power domain */
+	regmap_update_bits(priv->misc, SPEAR1340_PCM_CFG,
+			   SPEAR1340_PCM_CFG_SATA_POWER_EN, 0);
+	/* Wait for SATA reset assert completion */
+	msleep(20);
+
+	return 0;
+}
+
+static int spear1340_miphy_pcie_init(struct spear1340_miphy_priv *priv)
+{
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_MIPHY_CFG,
+			   SPEAR1340_PCIE_MIPHY_CFG_MASK,
+			   SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE);
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_SATA_CFG,
+			   SPEAR1340_PCIE_SATA_CFG_MASK,
+			   SPEAR1340_PCIE_CFG_VAL);
+
+	return 0;
+}
+
+static int spear1340_miphy_pcie_exit(struct spear1340_miphy_priv *priv)
+{
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_MIPHY_CFG,
+			   SPEAR1340_PCIE_MIPHY_CFG_MASK, 0);
+	regmap_update_bits(priv->misc, SPEAR1340_PCIE_SATA_CFG,
+			   SPEAR1340_PCIE_SATA_CFG_MASK, 0);
+
+	return 0;
+}
+
+static int spear1340_miphy_init(struct phy *phy)
+{
+	struct spear1340_miphy_priv *priv = phy_get_drvdata(phy);
+	int ret = 0;
+
+	if (priv->mode == SATA)
+		ret = spear1340_miphy_sata_init(priv);
+	else if (priv->mode == PCIE)
+		ret = spear1340_miphy_pcie_init(priv);
+
+	return ret;
+}
+
+static int spear1340_miphy_exit(struct phy *phy)
+{
+	struct spear1340_miphy_priv *priv = phy_get_drvdata(phy);
+	int ret = 0;
+
+	if (priv->mode == SATA)
+		ret = spear1340_miphy_sata_exit(priv);
+	else if (priv->mode == PCIE)
+		ret = spear1340_miphy_pcie_exit(priv);
+
+	return ret;
+}
+
+static const struct of_device_id spear1340_miphy_of_match[] = {
+	{ .compatible = "st,spear1340-miphy" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, spear1340_miphy_of_match);
+
+static const struct phy_ops spear1340_miphy_ops = {
+	.init = spear1340_miphy_init,
+	.exit = spear1340_miphy_exit,
+	.owner = THIS_MODULE,
+};
+
+#ifdef CONFIG_PM_SLEEP
+static int spear1340_miphy_suspend(struct device *dev)
+{
+	struct spear1340_miphy_priv *priv = dev_get_drvdata(dev);
+	int ret = 0;
+
+	if (priv->mode == SATA)
+		ret = spear1340_miphy_sata_exit(priv);
+
+	return ret;
+}
+
+static int spear1340_miphy_resume(struct device *dev)
+{
+	struct spear1340_miphy_priv *priv = dev_get_drvdata(dev);
+	int ret = 0;
+
+	if (priv->mode == SATA)
+		ret = spear1340_miphy_sata_init(priv);
+
+	return ret;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(spear1340_miphy_pm_ops, spear1340_miphy_suspend,
+			 spear1340_miphy_resume);
+
+static struct phy *spear1340_miphy_xlate(struct device *dev,
+					 const struct of_phandle_args *args)
+{
+	struct spear1340_miphy_priv *priv = dev_get_drvdata(dev);
+
+	if (args->args_count < 1) {
+		dev_err(dev, "DT did not pass correct no of args\n");
+		return ERR_PTR(-ENODEV);
+	}
+
+	priv->mode = args->args[0];
+
+	if (priv->mode != SATA && priv->mode != PCIE) {
+		dev_err(dev, "DT did not pass correct phy mode\n");
+		return ERR_PTR(-ENODEV);
+	}
+
+	return priv->phy;
+}
+
+static int spear1340_miphy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct spear1340_miphy_priv *priv;
+	struct phy_provider *phy_provider;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->misc =
+		syscon_regmap_lookup_by_phandle(dev->of_node, "misc");
+	if (IS_ERR(priv->misc)) {
+		dev_err(dev, "failed to find misc regmap\n");
+		return PTR_ERR(priv->misc);
+	}
+
+	priv->phy = devm_phy_create(dev, NULL, &spear1340_miphy_ops);
+	if (IS_ERR(priv->phy)) {
+		dev_err(dev, "failed to create SATA PCIe PHY\n");
+		return PTR_ERR(priv->phy);
+	}
+
+	dev_set_drvdata(dev, priv);
+	phy_set_drvdata(priv->phy, priv);
+
+	phy_provider =
+		devm_of_phy_provider_register(dev, spear1340_miphy_xlate);
+	if (IS_ERR(phy_provider)) {
+		dev_err(dev, "failed to register phy provider\n");
+		return PTR_ERR(phy_provider);
+	}
+
+	return 0;
+}
+
+static struct platform_driver spear1340_miphy_driver = {
+	.probe		= spear1340_miphy_probe,
+	.driver = {
+		.name = "spear1340-miphy",
+		.pm = &spear1340_miphy_pm_ops,
+		.of_match_table = spear1340_miphy_of_match,
+	},
+};
+
+module_platform_driver(spear1340_miphy_driver);
+
+MODULE_DESCRIPTION("ST SPEAR1340-MIPHY driver");
+MODULE_AUTHOR("Pratyush Anand <pratyush.anand@gmail.com>");
+MODULE_LICENSE("GPL v2");

linux-7.2.3/drivers/phy/st/phy-stih407-usb.c

@@ -0,0 +1,164 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics
+ *
+ * STMicroelectronics Generic PHY driver for STiH407 USB2.
+ *
+ * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
+ */
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/clk.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/mfd/syscon.h>
+#include <linux/phy/phy.h>
+
+#define PHYPARAM_REG	0
+#define PHYCTRL_REG	1
+
+/* Default PHY_SEL and REFCLKSEL configuration */
+#define STIH407_USB_PICOPHY_CTRL_PORT_CONF	0x6
+#define STIH407_USB_PICOPHY_CTRL_PORT_MASK	0x1f
+
+/* ports parameters overriding */
+#define STIH407_USB_PICOPHY_PARAM_DEF		0x39a4dc
+#define STIH407_USB_PICOPHY_PARAM_MASK		0xffffffff
+
+struct stih407_usb2_picophy {
+	struct phy *phy;
+	struct regmap *regmap;
+	struct device *dev;
+	struct reset_control *rstc;
+	struct reset_control *rstport;
+	int ctrl;
+	int param;
+};
+
+static int stih407_usb2_pico_ctrl(struct stih407_usb2_picophy *phy_dev)
+{
+	reset_control_deassert(phy_dev->rstc);
+
+	return regmap_update_bits(phy_dev->regmap, phy_dev->ctrl,
+				  STIH407_USB_PICOPHY_CTRL_PORT_MASK,
+				  STIH407_USB_PICOPHY_CTRL_PORT_CONF);
+}
+
+static int stih407_usb2_init_port(struct phy *phy)
+{
+	int ret;
+	struct stih407_usb2_picophy *phy_dev = phy_get_drvdata(phy);
+
+	stih407_usb2_pico_ctrl(phy_dev);
+
+	ret = regmap_update_bits(phy_dev->regmap,
+				 phy_dev->param,
+				 STIH407_USB_PICOPHY_PARAM_MASK,
+				 STIH407_USB_PICOPHY_PARAM_DEF);
+	if (ret)
+		return ret;
+
+	return reset_control_deassert(phy_dev->rstport);
+}
+
+static int stih407_usb2_exit_port(struct phy *phy)
+{
+	struct stih407_usb2_picophy *phy_dev = phy_get_drvdata(phy);
+
+	/*
+	 * Only port reset is asserted, phy global reset is kept untouched
+	 * as other ports may still be active. When all ports are in reset
+	 * state, assumption is made that power will be cut off on the phy, in
+	 * case of suspend for instance. Theoretically, asserting individual
+	 * reset (like here) or global reset should be equivalent.
+	 */
+	return reset_control_assert(phy_dev->rstport);
+}
+
+static const struct phy_ops stih407_usb2_picophy_data = {
+	.init = stih407_usb2_init_port,
+	.exit = stih407_usb2_exit_port,
+	.owner = THIS_MODULE,
+};
+
+static int stih407_usb2_picophy_probe(struct platform_device *pdev)
+{
+	struct stih407_usb2_picophy *phy_dev;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct phy_provider *phy_provider;
+	unsigned int syscon_args[2];
+	struct phy *phy;
+
+	phy_dev = devm_kzalloc(dev, sizeof(*phy_dev), GFP_KERNEL);
+	if (!phy_dev)
+		return -ENOMEM;
+
+	phy_dev->dev = dev;
+	dev_set_drvdata(dev, phy_dev);
+
+	phy_dev->rstc = devm_reset_control_get_shared(dev, "global");
+	if (IS_ERR(phy_dev->rstc)) {
+		dev_err(dev, "failed to ctrl picoPHY reset\n");
+		return PTR_ERR(phy_dev->rstc);
+	}
+
+	phy_dev->rstport = devm_reset_control_get_exclusive(dev, "port");
+	if (IS_ERR(phy_dev->rstport)) {
+		dev_err(dev, "failed to ctrl picoPHY reset\n");
+		return PTR_ERR(phy_dev->rstport);
+	}
+
+	/* Reset port by default: only deassert it in phy init */
+	reset_control_assert(phy_dev->rstport);
+
+	phy_dev->regmap = syscon_regmap_lookup_by_phandle_args(np, "st,syscfg",
+							       2, syscon_args);
+	if (IS_ERR(phy_dev->regmap)) {
+		dev_err(dev, "No syscfg phandle specified\n");
+		return PTR_ERR(phy_dev->regmap);
+	}
+
+	phy_dev->param = syscon_args[PHYPARAM_REG];
+	phy_dev->ctrl = syscon_args[PHYCTRL_REG];
+
+	phy = devm_phy_create(dev, NULL, &stih407_usb2_picophy_data);
+	if (IS_ERR(phy)) {
+		dev_err(dev, "failed to create Display Port PHY\n");
+		return PTR_ERR(phy);
+	}
+
+	phy_dev->phy = phy;
+	phy_set_drvdata(phy, phy_dev);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(phy_provider))
+		return PTR_ERR(phy_provider);
+
+	return 0;
+}
+
+static const struct of_device_id stih407_usb2_picophy_of_match[] = {
+	{ .compatible = "st,stih407-usb2-phy" },
+	{ /*sentinel */ },
+};
+
+MODULE_DEVICE_TABLE(of, stih407_usb2_picophy_of_match);
+
+static struct platform_driver stih407_usb2_picophy_driver = {
+	.probe = stih407_usb2_picophy_probe,
+	.driver = {
+		   .name = "stih407-usb-genphy",
+		   .of_match_table = stih407_usb2_picophy_of_match,
+		   }
+};
+
+module_platform_driver(stih407_usb2_picophy_driver);
+
+MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
+MODULE_DESCRIPTION("STMicroelectronics Generic picoPHY driver for STiH407");
+MODULE_LICENSE("GPL v2");

linux-7.2.3/drivers/phy/st/phy-stm32-combophy.c

@@ -0,0 +1,605 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * STMicroelectronics COMBOPHY STM32MP25 Controller driver.
+ *
+ * Copyright (C) 2024 STMicroelectronics
+ * Author: Christian Bruel <christian.bruel@foss.st.com>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <dt-bindings/phy/phy.h>
+
+#define SYSCFG_COMBOPHY_CR1 0x4c00
+#define SYSCFG_COMBOPHY_CR2 0x4c04
+#define SYSCFG_COMBOPHY_CR4 0x4c0c
+#define SYSCFG_COMBOPHY_CR5 0x4c10
+#define SYSCFG_COMBOPHY_SR  0x4c14
+#define SYSCFG_PCIEPRGCR    0x6080
+
+/* SYSCFG PCIEPRGCR */
+#define STM32MP25_PCIEPRGCR_EN	  BIT(0)
+#define STM32MP25_PCIEPRG_IMPCTRL_OHM     GENMASK(3, 1)
+#define STM32MP25_PCIEPRG_IMPCTRL_VSWING  GENMASK(5, 4)
+
+/* SYSCFG SYSCFG_COMBOPHY_SR */
+#define STM32MP25_PIPE0_PHYSTATUS BIT(1)
+
+/* SYSCFG CR1 */
+#define SYSCFG_COMBOPHY_CR1_REFUSEPAD BIT(0)
+#define SYSCFG_COMBOPHY_CR1_MPLLMULT GENMASK(7, 1)
+#define SYSCFG_COMBOPHY_CR1_REFCLKSEL GENMASK(16, 8)
+#define SYSCFG_COMBOPHY_CR1_REFCLKDIV2 BIT(17)
+#define SYSCFG_COMBOPHY_CR1_REFSSPEN BIT(18)
+#define SYSCFG_COMBOPHY_CR1_SSCEN BIT(19)
+
+/* SYSCFG CR4 */
+#define SYSCFG_COMBOPHY_CR4_RX0_EQ GENMASK(2, 0)
+
+#define MPLLMULT_19_2 (0x02u << 1)
+#define MPLLMULT_20   (0x7du << 1)
+#define MPLLMULT_24   (0x68u << 1)
+#define MPLLMULT_25   (0x64u << 1)
+#define MPLLMULT_26   (0x60u << 1)
+#define MPLLMULT_38_4 (0x41u << 1)
+#define MPLLMULT_48   (0x6cu << 1)
+#define MPLLMULT_50   (0x32u << 1)
+#define MPLLMULT_52   (0x30u << 1)
+#define MPLLMULT_100  (0x19u << 1)
+
+#define REFCLKSEL_0   0
+#define REFCLKSEL_1   (0x108u << 8)
+
+#define REFCLDIV_0    0
+
+/* SYSCFG CR2 */
+#define SYSCFG_COMBOPHY_CR2_MODESEL GENMASK(1, 0)
+#define SYSCFG_COMBOPHY_CR2_ISO_DIS BIT(15)
+
+#define COMBOPHY_MODESEL_PCIE 0
+#define COMBOPHY_MODESEL_USB  3
+
+/* SYSCFG CR5 */
+#define SYSCFG_COMBOPHY_CR5_COMMON_CLOCKS BIT(12)
+
+#define COMBOPHY_SUP_ANA_MPLL_LOOP_CTL 0xc0
+#define COMBOPHY_PROP_CNTRL GENMASK(7, 4)
+
+/* Required apb/ker clocks first, optional pad last. */
+static const char * const combophy_clks[] = {"apb", "ker", "pad"};
+#define APB_CLK 0
+#define KER_CLK 1
+#define PAD_CLK 2
+
+struct stm32_combophy {
+	struct phy *phy;
+	struct regmap *regmap;
+	struct device *dev;
+	void __iomem *base;
+	struct reset_control *phy_reset;
+	struct clk_bulk_data clks[ARRAY_SIZE(combophy_clks)];
+	int num_clks;
+	bool have_pad_clk;
+	unsigned int type;
+	bool is_init;
+	int irq_wakeup;
+};
+
+struct clk_impedance  {
+	u32 microohm;
+	u32 vswing[4];
+};
+
+/*
+ * lookup table to hold the settings needed for a ref clock frequency
+ * impedance, the offset is used to set the IMP_CTL and DE_EMP bit of the
+ * PRG_IMP_CTRL register. Use ordered discrete values in the table
+ */
+static const struct clk_impedance imp_lookup[] = {
+	{ 6090000, { 442000, 564000, 684000, 802000 } },
+	{ 5662000, { 528000, 621000, 712000, 803000 } },
+	{ 5292000, { 491000, 596000, 700000, 802000 } },
+	{ 4968000, { 558000, 640000, 722000, 803000 } },
+	{ 4684000, { 468000, 581000, 692000, 802000 } },
+	{ 4429000, { 554000, 613000, 717000, 803000 } },
+	{ 4204000, { 511000, 609000, 706000, 802000 } },
+	{ 3999000, { 571000, 648000, 726000, 803000 } }
+};
+#define DEFAULT_IMP_INDEX 3 /* Default impedance is 50 Ohm */
+
+static int stm32_impedance_tune(struct stm32_combophy *combophy)
+{
+	u8 imp_size = ARRAY_SIZE(imp_lookup);
+	u8 vswing_size = ARRAY_SIZE(imp_lookup[0].vswing);
+	u8 imp_of, vswing_of;
+	u32 max_imp = imp_lookup[0].microohm;
+	u32 min_imp = imp_lookup[imp_size - 1].microohm;
+	u32 max_vswing;
+	u32 min_vswing = imp_lookup[0].vswing[0];
+	u32 val;
+
+	if (!of_property_read_u32(combophy->dev->of_node, "st,output-micro-ohms", &val)) {
+		if (val < min_imp || val > max_imp) {
+			dev_err(combophy->dev, "Invalid value %u for output ohm\n", val);
+			return -EINVAL;
+		}
+
+		for (imp_of = 0; imp_of < ARRAY_SIZE(imp_lookup); imp_of++)
+			if (imp_lookup[imp_of].microohm <= val)
+				break;
+
+		if (WARN_ON(imp_of == ARRAY_SIZE(imp_lookup)))
+			return -EINVAL;
+
+		dev_dbg(combophy->dev, "Set %u micro-ohms output impedance\n",
+			imp_lookup[imp_of].microohm);
+
+		regmap_update_bits(combophy->regmap, SYSCFG_PCIEPRGCR,
+				   STM32MP25_PCIEPRG_IMPCTRL_OHM,
+				   FIELD_PREP(STM32MP25_PCIEPRG_IMPCTRL_OHM, imp_of));
+	} else
+		imp_of = DEFAULT_IMP_INDEX;
+
+	if (!of_property_read_u32(combophy->dev->of_node, "st,output-vswing-microvolt", &val)) {
+		max_vswing = imp_lookup[imp_of].vswing[vswing_size - 1];
+
+		if (val < min_vswing || val > max_vswing) {
+			dev_err(combophy->dev, "Invalid value %u for output vswing\n", val);
+			return -EINVAL;
+		}
+
+		for (vswing_of = 0; vswing_of < ARRAY_SIZE(imp_lookup[imp_of].vswing); vswing_of++)
+			if (imp_lookup[imp_of].vswing[vswing_of] >= val)
+				break;
+
+		if (WARN_ON(vswing_of == ARRAY_SIZE(imp_lookup[imp_of].vswing)))
+			return -EINVAL;
+
+		dev_dbg(combophy->dev, "Set %u microvolt swing\n",
+			 imp_lookup[imp_of].vswing[vswing_of]);
+
+		regmap_update_bits(combophy->regmap, SYSCFG_PCIEPRGCR,
+				   STM32MP25_PCIEPRG_IMPCTRL_VSWING,
+				   FIELD_PREP(STM32MP25_PCIEPRG_IMPCTRL_VSWING, vswing_of));
+	}
+
+	return 0;
+}
+
+static int stm32_combophy_pll_init(struct stm32_combophy *combophy)
+{
+	int ret;
+	u32 refclksel, pllmult, propcntrl, val;
+	u32 clk_rate;
+	struct clk *clk;
+	u32 cr1_val = 0, cr1_mask = 0;
+
+	if (combophy->have_pad_clk)
+		clk = combophy->clks[PAD_CLK].clk;
+	else
+		clk = combophy->clks[KER_CLK].clk;
+
+	clk_rate = clk_get_rate(clk);
+
+	dev_dbg(combophy->dev, "%s pll init rate %d\n",
+		combophy->have_pad_clk ? "External" : "Ker", clk_rate);
+
+	if (combophy->type != PHY_TYPE_PCIE) {
+		cr1_mask |= SYSCFG_COMBOPHY_CR1_REFSSPEN;
+		cr1_val |= SYSCFG_COMBOPHY_CR1_REFSSPEN;
+	}
+
+	if (of_property_present(combophy->dev->of_node, "st,ssc-on")) {
+		dev_dbg(combophy->dev, "Enabling clock with SSC\n");
+		cr1_mask |= SYSCFG_COMBOPHY_CR1_SSCEN;
+		cr1_val |= SYSCFG_COMBOPHY_CR1_SSCEN;
+	}
+
+	switch (clk_rate) {
+	case 100000000:
+		pllmult = MPLLMULT_100;
+		refclksel = REFCLKSEL_0;
+		propcntrl = 0x8u << 4;
+		break;
+	case 19200000:
+		pllmult = MPLLMULT_19_2;
+		refclksel = REFCLKSEL_1;
+		propcntrl = 0x8u << 4;
+		break;
+	case 25000000:
+		pllmult = MPLLMULT_25;
+		refclksel = REFCLKSEL_0;
+		propcntrl = 0xeu << 4;
+		break;
+	case 24000000:
+		pllmult = MPLLMULT_24;
+		refclksel = REFCLKSEL_1;
+		propcntrl = 0xeu << 4;
+		break;
+	case 20000000:
+		pllmult = MPLLMULT_20;
+		refclksel = REFCLKSEL_0;
+		propcntrl = 0xeu << 4;
+		break;
+	default:
+		dev_err(combophy->dev, "Invalid rate 0x%x\n", clk_rate);
+		return -EINVAL;
+	}
+
+	cr1_mask |= SYSCFG_COMBOPHY_CR1_REFCLKDIV2;
+	cr1_val |= REFCLDIV_0;
+
+	cr1_mask |= SYSCFG_COMBOPHY_CR1_REFCLKSEL;
+	cr1_val |= refclksel;
+
+	cr1_mask |= SYSCFG_COMBOPHY_CR1_MPLLMULT;
+	cr1_val |= pllmult;
+
+	/*
+	 * vddcombophy is interconnected with vddcore. Isolation bit should be unset
+	 * before using the ComboPHY.
+	 */
+	regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR2,
+			   SYSCFG_COMBOPHY_CR2_ISO_DIS, SYSCFG_COMBOPHY_CR2_ISO_DIS);
+
+	reset_control_assert(combophy->phy_reset);
+
+	if (combophy->type == PHY_TYPE_PCIE) {
+		ret = stm32_impedance_tune(combophy);
+		if (ret)
+			goto out_iso;
+
+		cr1_mask |= SYSCFG_COMBOPHY_CR1_REFUSEPAD;
+		cr1_val |= combophy->have_pad_clk ? SYSCFG_COMBOPHY_CR1_REFUSEPAD : 0;
+	}
+
+	if (!of_property_read_u32(combophy->dev->of_node, "st,rx-equalizer", &val)) {
+		dev_dbg(combophy->dev, "Set RX equalizer %u\n", val);
+		if (val > SYSCFG_COMBOPHY_CR4_RX0_EQ) {
+			dev_err(combophy->dev, "Invalid value %u for rx0 equalizer\n", val);
+			ret = -EINVAL;
+			goto out_iso;
+		}
+
+		regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR4,
+			   SYSCFG_COMBOPHY_CR4_RX0_EQ, val);
+	}
+
+	regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR1, cr1_mask, cr1_val);
+
+	/*
+	 * Force elasticity buffer to be tuned for the reference clock as
+	 * the separated clock model is not supported
+	 */
+	regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR5,
+			   SYSCFG_COMBOPHY_CR5_COMMON_CLOCKS, SYSCFG_COMBOPHY_CR5_COMMON_CLOCKS);
+
+	reset_control_deassert(combophy->phy_reset);
+
+	ret = regmap_read_poll_timeout(combophy->regmap, SYSCFG_COMBOPHY_SR, val,
+				       !(val & STM32MP25_PIPE0_PHYSTATUS),
+				       10, 1000);
+	if (ret) {
+		dev_err(combophy->dev, "timeout, cannot lock PLL\n");
+		if (combophy->type == PHY_TYPE_PCIE && !combophy->have_pad_clk)
+			regmap_update_bits(combophy->regmap, SYSCFG_PCIEPRGCR,
+					   STM32MP25_PCIEPRGCR_EN, 0);
+
+		if (combophy->type != PHY_TYPE_PCIE)
+			regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR1,
+					   SYSCFG_COMBOPHY_CR1_REFSSPEN, 0);
+
+		goto out;
+	}
+
+
+	if (combophy->type == PHY_TYPE_PCIE) {
+		if (!combophy->have_pad_clk)
+			regmap_update_bits(combophy->regmap, SYSCFG_PCIEPRGCR,
+					   STM32MP25_PCIEPRGCR_EN, STM32MP25_PCIEPRGCR_EN);
+
+		val = readl_relaxed(combophy->base + COMBOPHY_SUP_ANA_MPLL_LOOP_CTL);
+		val &= ~COMBOPHY_PROP_CNTRL;
+		val |= propcntrl;
+		writel_relaxed(val, combophy->base + COMBOPHY_SUP_ANA_MPLL_LOOP_CTL);
+	}
+
+	return 0;
+
+out_iso:
+	reset_control_deassert(combophy->phy_reset);
+
+out:
+	regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR2,
+			   SYSCFG_COMBOPHY_CR2_ISO_DIS, 0);
+
+	return ret;
+}
+
+static struct phy *stm32_combophy_xlate(struct device *dev,
+					const struct of_phandle_args *args)
+{
+	struct stm32_combophy *combophy = dev_get_drvdata(dev);
+	unsigned int type;
+
+	if (args->args_count != 1) {
+		dev_err(dev, "invalid number of cells in 'phy' property\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	type = args->args[0];
+	if (type != PHY_TYPE_USB3 && type != PHY_TYPE_PCIE) {
+		dev_err(dev, "unsupported device type: %d\n", type);
+		return ERR_PTR(-EINVAL);
+	}
+
+	if (combophy->have_pad_clk && type != PHY_TYPE_PCIE) {
+		dev_err(dev, "Invalid use of clk_pad for USB3 mode\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	combophy->type = type;
+
+	return combophy->phy;
+}
+
+static int stm32_combophy_set_mode(struct stm32_combophy *combophy)
+{
+	int type = combophy->type;
+	u32 val;
+
+	switch (type) {
+	case PHY_TYPE_PCIE:
+		dev_dbg(combophy->dev, "setting PCIe ComboPHY\n");
+		val = COMBOPHY_MODESEL_PCIE;
+		break;
+	case PHY_TYPE_USB3:
+		dev_dbg(combophy->dev, "setting USB3 ComboPHY\n");
+		val = COMBOPHY_MODESEL_USB;
+		break;
+	default:
+		dev_err(combophy->dev, "Invalid PHY mode %d\n", type);
+		return -EINVAL;
+	}
+
+	return regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR2,
+				  SYSCFG_COMBOPHY_CR2_MODESEL, val);
+}
+
+static int stm32_combophy_suspend_noirq(struct device *dev)
+{
+	struct stm32_combophy *combophy = dev_get_drvdata(dev);
+
+	/*
+	 * Clocks should be turned off since it is not needed for
+	 * wakeup capability. In case usb-remote wakeup is not enabled,
+	 * combo-phy is already turned off by HCD driver using exit callback
+	 */
+	if (combophy->is_init) {
+		clk_bulk_disable_unprepare(combophy->num_clks, combophy->clks);
+
+		/* since wakeup is enabled for ctrl */
+		enable_irq_wake(combophy->irq_wakeup);
+	}
+
+	return 0;
+}
+
+static int stm32_combophy_resume_noirq(struct device *dev)
+{
+	struct stm32_combophy *combophy = dev_get_drvdata(dev);
+	int ret;
+
+	/*
+	 * If clocks was turned off by suspend call for wakeup then needs
+	 * to be turned back ON in resume. In case usb-remote wakeup is not
+	 * enabled, clocks already turned ON by HCD driver using init callback
+	 */
+	if (combophy->is_init) {
+		/* since wakeup was enabled for ctrl */
+		disable_irq_wake(combophy->irq_wakeup);
+
+		ret = clk_bulk_prepare_enable(combophy->num_clks, combophy->clks);
+		if (ret) {
+			dev_err(dev, "can't enable clocks (%d)\n", ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int stm32_combophy_exit(struct phy *phy)
+{
+	struct stm32_combophy *combophy = phy_get_drvdata(phy);
+	struct device *dev = combophy->dev;
+
+	combophy->is_init = false;
+
+	if (combophy->type == PHY_TYPE_PCIE && !combophy->have_pad_clk)
+		regmap_update_bits(combophy->regmap, SYSCFG_PCIEPRGCR,
+				   STM32MP25_PCIEPRGCR_EN, 0);
+
+	if (combophy->type != PHY_TYPE_PCIE)
+		regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR1,
+				   SYSCFG_COMBOPHY_CR1_REFSSPEN, 0);
+
+	regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR2,
+			   SYSCFG_COMBOPHY_CR2_ISO_DIS, 0);
+
+	clk_bulk_disable_unprepare(combophy->num_clks, combophy->clks);
+
+	pm_runtime_put_noidle(dev);
+
+	return 0;
+}
+
+static int stm32_combophy_init(struct phy *phy)
+{
+	struct stm32_combophy *combophy = phy_get_drvdata(phy);
+	struct device *dev = combophy->dev;
+	int ret;
+
+	pm_runtime_get_noresume(dev);
+
+	ret = clk_bulk_prepare_enable(combophy->num_clks, combophy->clks);
+	if (ret) {
+		dev_err(dev, "can't enable clocks (%d)\n", ret);
+		pm_runtime_put_noidle(dev);
+		return ret;
+	}
+
+	ret = stm32_combophy_set_mode(combophy);
+	if (ret) {
+		dev_err(dev, "combophy mode not set\n");
+		clk_bulk_disable_unprepare(combophy->num_clks, combophy->clks);
+		pm_runtime_put_noidle(dev);
+		return ret;
+	}
+
+	ret = stm32_combophy_pll_init(combophy);
+	if (ret) {
+		clk_bulk_disable_unprepare(combophy->num_clks, combophy->clks);
+		pm_runtime_put_noidle(dev);
+		return ret;
+	}
+
+	pm_runtime_disable(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+
+	combophy->is_init = true;
+
+	return ret;
+}
+
+static const struct phy_ops stm32_combophy_phy_data = {
+	.init = stm32_combophy_init,
+	.exit = stm32_combophy_exit,
+	.owner = THIS_MODULE
+};
+
+static irqreturn_t stm32_combophy_irq_wakeup_handler(int irq, void *dev_id)
+{
+	return IRQ_HANDLED;
+}
+
+static int stm32_combophy_get_clocks(struct stm32_combophy *combophy)
+{
+	int i, ret;
+
+	for (i = 0; i < ARRAY_SIZE(combophy_clks); i++)
+		combophy->clks[i].id = combophy_clks[i];
+
+	combophy->num_clks = ARRAY_SIZE(combophy_clks) - 1;
+
+	ret = devm_clk_bulk_get(combophy->dev, combophy->num_clks, combophy->clks);
+	if (ret)
+		return ret;
+
+	ret = devm_clk_bulk_get_optional(combophy->dev, 1, combophy->clks + combophy->num_clks);
+	if (ret)
+		return ret;
+
+	if (combophy->clks[combophy->num_clks].clk != NULL) {
+		combophy->have_pad_clk = true;
+		combophy->num_clks++;
+	}
+
+	return 0;
+}
+
+static int stm32_combophy_probe(struct platform_device *pdev)
+{
+	struct stm32_combophy *combophy;
+	struct device *dev = &pdev->dev;
+	struct phy_provider *phy_provider;
+	int ret, irq;
+
+	combophy = devm_kzalloc(dev, sizeof(*combophy), GFP_KERNEL);
+	if (!combophy)
+		return -ENOMEM;
+
+	combophy->dev = dev;
+
+	dev_set_drvdata(dev, combophy);
+
+	combophy->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(combophy->base))
+		return PTR_ERR(combophy->base);
+
+	ret = stm32_combophy_get_clocks(combophy);
+	if (ret)
+		return ret;
+
+	combophy->phy_reset = devm_reset_control_get_exclusive(dev, "phy");
+	if (IS_ERR(combophy->phy_reset))
+		return dev_err_probe(dev, PTR_ERR(combophy->phy_reset),
+				     "Failed to get PHY reset\n");
+
+	combophy->regmap = syscon_regmap_lookup_by_compatible("st,stm32mp25-syscfg");
+	if (IS_ERR(combophy->regmap))
+		return dev_err_probe(dev, PTR_ERR(combophy->regmap),
+				     "No syscfg specified\n");
+
+	combophy->phy = devm_phy_create(dev, NULL, &stm32_combophy_phy_data);
+	if (IS_ERR(combophy->phy))
+		return dev_err_probe(dev, PTR_ERR(combophy->phy),
+				     "failed to create PCIe/USB3 ComboPHY\n");
+
+	if (device_property_read_bool(dev, "wakeup-source")) {
+		irq = platform_get_irq(pdev, 0);
+		if (irq < 0)
+			return dev_err_probe(dev, irq, "failed to get IRQ\n");
+		combophy->irq_wakeup = irq;
+
+		ret = devm_request_threaded_irq(dev, combophy->irq_wakeup, NULL,
+						stm32_combophy_irq_wakeup_handler, IRQF_ONESHOT,
+						NULL, NULL);
+		if (ret)
+			return dev_err_probe(dev, ret, "unable to request wake IRQ %d\n",
+						 combophy->irq_wakeup);
+	}
+
+	ret = devm_pm_runtime_enable(dev);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to enable pm runtime\n");
+
+	phy_set_drvdata(combophy->phy, combophy);
+
+	phy_provider = devm_of_phy_provider_register(dev, stm32_combophy_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct dev_pm_ops stm32_combophy_pm_ops = {
+	NOIRQ_SYSTEM_SLEEP_PM_OPS(stm32_combophy_suspend_noirq,
+				  stm32_combophy_resume_noirq)
+};
+
+static const struct of_device_id stm32_combophy_of_match[] = {
+	{ .compatible = "st,stm32mp25-combophy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, stm32_combophy_of_match);
+
+static struct platform_driver stm32_combophy_driver = {
+	.probe = stm32_combophy_probe,
+	.driver = {
+		   .name = "stm32-combophy",
+		   .of_match_table = stm32_combophy_of_match,
+		   .pm = pm_sleep_ptr(&stm32_combophy_pm_ops)
+	}
+};
+
+module_platform_driver(stm32_combophy_driver);
+
+MODULE_AUTHOR("Christian Bruel <christian.bruel@foss.st.com>");
+MODULE_DESCRIPTION("STM32MP25 Combophy USB3/PCIe controller driver");
+MODULE_LICENSE("GPL");

linux-7.2.3/drivers/phy/st/phy-stm32-usbphyc.c

@@ -0,0 +1,826 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * STMicroelectronics STM32 USB PHY Controller driver
+ *
+ * Copyright (C) 2018 STMicroelectronics
+ * Author(s): Amelie Delaunay <amelie.delaunay@st.com>.
+ */
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+#include <linux/units.h>
+
+#define STM32_USBPHYC_PLL	0x0
+#define STM32_USBPHYC_MISC	0x8
+#define STM32_USBPHYC_MONITOR(X) (0x108 + ((X) * 0x100))
+#define STM32_USBPHYC_TUNE(X)	(0x10C + ((X) * 0x100))
+#define STM32_USBPHYC_VERSION	0x3F4
+
+/* STM32_USBPHYC_PLL bit fields */
+#define PLLNDIV			GENMASK(6, 0)
+#define PLLFRACIN		GENMASK(25, 10)
+#define PLLEN			BIT(26)
+#define PLLSTRB			BIT(27)
+#define PLLSTRBYP		BIT(28)
+#define PLLFRACCTL		BIT(29)
+#define PLLDITHEN0		BIT(30)
+#define PLLDITHEN1		BIT(31)
+
+/* STM32_USBPHYC_MISC bit fields */
+#define SWITHOST		BIT(0)
+
+/* STM32_USBPHYC_MONITOR bit fields */
+#define STM32_USBPHYC_MON_OUT	GENMASK(3, 0)
+#define STM32_USBPHYC_MON_SEL	GENMASK(8, 4)
+#define STM32_USBPHYC_MON_SEL_LOCKP 0x1F
+#define STM32_USBPHYC_MON_OUT_LOCKP BIT(3)
+
+/* STM32_USBPHYC_TUNE bit fields */
+#define INCURREN		BIT(0)
+#define INCURRINT		BIT(1)
+#define LFSCAPEN		BIT(2)
+#define HSDRVSLEW		BIT(3)
+#define HSDRVDCCUR		BIT(4)
+#define HSDRVDCLEV		BIT(5)
+#define HSDRVCURINCR		BIT(6)
+#define FSDRVRFADJ		BIT(7)
+#define HSDRVRFRED		BIT(8)
+#define HSDRVCHKITRM		GENMASK(12, 9)
+#define HSDRVCHKZTRM		GENMASK(14, 13)
+#define OTPCOMP			GENMASK(19, 15)
+#define SQLCHCTL		GENMASK(21, 20)
+#define HDRXGNEQEN		BIT(22)
+#define HSRXOFF			GENMASK(24, 23)
+#define HSFALLPREEM		BIT(25)
+#define SHTCCTCTLPROT		BIT(26)
+#define STAGSEL			BIT(27)
+
+enum boosting_vals {
+	BOOST_1000_UA = 1000,
+	BOOST_2000_UA = 2000,
+};
+
+enum dc_level_vals {
+	DC_NOMINAL,
+	DC_PLUS_5_TO_7_MV,
+	DC_PLUS_10_TO_14_MV,
+	DC_MINUS_5_TO_7_MV,
+	DC_MAX,
+};
+
+enum current_trim {
+	CUR_NOMINAL,
+	CUR_PLUS_1_56_PCT,
+	CUR_PLUS_3_12_PCT,
+	CUR_PLUS_4_68_PCT,
+	CUR_PLUS_6_24_PCT,
+	CUR_PLUS_7_8_PCT,
+	CUR_PLUS_9_36_PCT,
+	CUR_PLUS_10_92_PCT,
+	CUR_PLUS_12_48_PCT,
+	CUR_PLUS_14_04_PCT,
+	CUR_PLUS_15_6_PCT,
+	CUR_PLUS_17_16_PCT,
+	CUR_PLUS_19_01_PCT,
+	CUR_PLUS_20_58_PCT,
+	CUR_PLUS_22_16_PCT,
+	CUR_PLUS_23_73_PCT,
+	CUR_MAX,
+};
+
+enum impedance_trim {
+	IMP_NOMINAL,
+	IMP_MINUS_2_OHMS,
+	IMP_MINUS_4_OMHS,
+	IMP_MINUS_6_OHMS,
+	IMP_MAX,
+};
+
+enum squelch_level {
+	SQLCH_NOMINAL,
+	SQLCH_PLUS_7_MV,
+	SQLCH_MINUS_5_MV,
+	SQLCH_PLUS_14_MV,
+	SQLCH_MAX,
+};
+
+enum rx_offset {
+	NO_RX_OFFSET,
+	RX_OFFSET_PLUS_5_MV,
+	RX_OFFSET_PLUS_10_MV,
+	RX_OFFSET_MINUS_5_MV,
+	RX_OFFSET_MAX,
+};
+
+/* STM32_USBPHYC_VERSION bit fields */
+#define MINREV			GENMASK(3, 0)
+#define MAJREV			GENMASK(7, 4)
+
+#define PLL_FVCO_MHZ		2880
+#define PLL_INFF_MIN_RATE_HZ	19200000
+#define PLL_INFF_MAX_RATE_HZ	38400000
+
+struct pll_params {
+	u8 ndiv;
+	u16 frac;
+};
+
+struct stm32_usbphyc_phy {
+	struct phy *phy;
+	struct stm32_usbphyc *usbphyc;
+	struct regulator *vbus;
+	u32 index;
+	bool active;
+	u32 tune;
+};
+
+struct stm32_usbphyc {
+	struct device *dev;
+	void __iomem *base;
+	struct clk *clk;
+	struct reset_control *rst;
+	struct stm32_usbphyc_phy **phys;
+	int nphys;
+	struct regulator *vdda1v1;
+	struct regulator *vdda1v8;
+	atomic_t n_pll_cons;
+	struct clk_hw clk48_hw;
+	int switch_setup;
+};
+
+static inline void stm32_usbphyc_set_bits(void __iomem *reg, u32 bits)
+{
+	writel_relaxed(readl_relaxed(reg) | bits, reg);
+}
+
+static inline void stm32_usbphyc_clr_bits(void __iomem *reg, u32 bits)
+{
+	writel_relaxed(readl_relaxed(reg) & ~bits, reg);
+}
+
+static int stm32_usbphyc_regulators_enable(struct stm32_usbphyc *usbphyc)
+{
+	int ret;
+
+	ret = regulator_enable(usbphyc->vdda1v1);
+	if (ret)
+		return ret;
+
+	ret = regulator_enable(usbphyc->vdda1v8);
+	if (ret)
+		goto vdda1v1_disable;
+
+	return 0;
+
+vdda1v1_disable:
+	regulator_disable(usbphyc->vdda1v1);
+
+	return ret;
+}
+
+static int stm32_usbphyc_regulators_disable(struct stm32_usbphyc *usbphyc)
+{
+	int ret;
+
+	ret = regulator_disable(usbphyc->vdda1v8);
+	if (ret)
+		return ret;
+
+	ret = regulator_disable(usbphyc->vdda1v1);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static void stm32_usbphyc_get_pll_params(u32 clk_rate,
+					 struct pll_params *pll_params)
+{
+	unsigned long long fvco, ndiv, frac;
+
+	/*    _
+	 *   | FVCO = INFF*2*(NDIV + FRACT/2^16) when DITHER_DISABLE[1] = 1
+	 *   | FVCO = 2880MHz
+	 *  <
+	 *   | NDIV = integer part of input bits to set the LDF
+	 *   |_FRACT = fractional part of input bits to set the LDF
+	 *  =>	PLLNDIV = integer part of (FVCO / (INFF*2))
+	 *  =>	PLLFRACIN = fractional part of(FVCO / INFF*2) * 2^16
+	 * <=>  PLLFRACIN = ((FVCO / (INFF*2)) - PLLNDIV) * 2^16
+	 */
+	fvco = (unsigned long long)PLL_FVCO_MHZ * HZ_PER_MHZ;
+
+	ndiv = fvco;
+	do_div(ndiv, (clk_rate * 2));
+	pll_params->ndiv = (u8)ndiv;
+
+	frac = fvco * (1 << 16);
+	do_div(frac, (clk_rate * 2));
+	frac = frac - (ndiv * (1 << 16));
+	pll_params->frac = (u16)frac;
+}
+
+static int stm32_usbphyc_pll_init(struct stm32_usbphyc *usbphyc)
+{
+	struct pll_params pll_params;
+	u32 clk_rate = clk_get_rate(usbphyc->clk);
+	u32 ndiv, frac;
+	u32 usbphyc_pll;
+
+	if ((clk_rate < PLL_INFF_MIN_RATE_HZ) ||
+	    (clk_rate > PLL_INFF_MAX_RATE_HZ)) {
+		dev_err(usbphyc->dev, "input clk freq (%dHz) out of range\n",
+			clk_rate);
+		return -EINVAL;
+	}
+
+	stm32_usbphyc_get_pll_params(clk_rate, &pll_params);
+	ndiv = FIELD_PREP(PLLNDIV, pll_params.ndiv);
+	frac = FIELD_PREP(PLLFRACIN, pll_params.frac);
+
+	usbphyc_pll = PLLDITHEN1 | PLLDITHEN0 | PLLSTRBYP | ndiv;
+
+	if (pll_params.frac)
+		usbphyc_pll |= PLLFRACCTL | frac;
+
+	writel_relaxed(usbphyc_pll, usbphyc->base + STM32_USBPHYC_PLL);
+
+	dev_dbg(usbphyc->dev, "input clk freq=%dHz, ndiv=%lu, frac=%lu\n",
+		clk_rate, FIELD_GET(PLLNDIV, usbphyc_pll),
+		FIELD_GET(PLLFRACIN, usbphyc_pll));
+
+	return 0;
+}
+
+static int __stm32_usbphyc_pll_disable(struct stm32_usbphyc *usbphyc)
+{
+	void __iomem *pll_reg = usbphyc->base + STM32_USBPHYC_PLL;
+	u32 pllen;
+
+	stm32_usbphyc_clr_bits(pll_reg, PLLEN);
+
+	/* Wait for minimum width of powerdown pulse (ENABLE = Low) */
+	if (readl_relaxed_poll_timeout(pll_reg, pllen, !(pllen & PLLEN), 5, 50))
+		dev_err(usbphyc->dev, "PLL not reset\n");
+
+	return stm32_usbphyc_regulators_disable(usbphyc);
+}
+
+static int stm32_usbphyc_pll_disable(struct stm32_usbphyc *usbphyc)
+{
+	/* Check if a phy port is still active or clk48 in use */
+	if (atomic_dec_return(&usbphyc->n_pll_cons) > 0)
+		return 0;
+
+	return __stm32_usbphyc_pll_disable(usbphyc);
+}
+
+static int stm32_usbphyc_pll_enable(struct stm32_usbphyc *usbphyc)
+{
+	void __iomem *pll_reg = usbphyc->base + STM32_USBPHYC_PLL;
+	bool pllen = readl_relaxed(pll_reg) & PLLEN;
+	int ret;
+
+	/*
+	 * Check if a phy port or clk48 prepare has configured the pll
+	 * and ensure the PLL is enabled
+	 */
+	if (atomic_inc_return(&usbphyc->n_pll_cons) > 1 && pllen)
+		return 0;
+
+	if (pllen) {
+		/*
+		 * PLL shouldn't be enabled without known consumer,
+		 * disable it and reinit n_pll_cons
+		 */
+		dev_warn(usbphyc->dev, "PLL enabled without known consumers\n");
+
+		ret = __stm32_usbphyc_pll_disable(usbphyc);
+		if (ret)
+			goto dec_n_pll_cons;
+	}
+
+	ret = stm32_usbphyc_regulators_enable(usbphyc);
+	if (ret)
+		goto dec_n_pll_cons;
+
+	ret = stm32_usbphyc_pll_init(usbphyc);
+	if (ret)
+		goto reg_disable;
+
+	stm32_usbphyc_set_bits(pll_reg, PLLEN);
+
+	/* Wait for maximum lock time */
+	usleep_range(200, 300);
+
+	return 0;
+
+reg_disable:
+	stm32_usbphyc_regulators_disable(usbphyc);
+
+dec_n_pll_cons:
+	atomic_dec(&usbphyc->n_pll_cons);
+
+	return ret;
+}
+
+static int stm32_usbphyc_phy_init(struct phy *phy)
+{
+	struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy);
+	struct stm32_usbphyc *usbphyc = usbphyc_phy->usbphyc;
+	u32 reg_mon = STM32_USBPHYC_MONITOR(usbphyc_phy->index);
+	u32 monsel = FIELD_PREP(STM32_USBPHYC_MON_SEL,
+				STM32_USBPHYC_MON_SEL_LOCKP);
+	u32 monout;
+	int ret;
+
+	ret = stm32_usbphyc_pll_enable(usbphyc);
+	if (ret)
+		return ret;
+
+	/* Check that PLL Lock input to PHY is High */
+	writel_relaxed(monsel, usbphyc->base + reg_mon);
+	ret = readl_relaxed_poll_timeout(usbphyc->base + reg_mon, monout,
+					 (monout & STM32_USBPHYC_MON_OUT_LOCKP),
+					 100, 1000);
+	if (ret) {
+		dev_err(usbphyc->dev, "PLL Lock input to PHY is Low (val=%x)\n",
+			(u32)(monout & STM32_USBPHYC_MON_OUT));
+		goto pll_disable;
+	}
+
+	usbphyc_phy->active = true;
+
+	return 0;
+
+pll_disable:
+	stm32_usbphyc_pll_disable(usbphyc);
+
+	return ret;
+}
+
+static int stm32_usbphyc_phy_exit(struct phy *phy)
+{
+	struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy);
+	struct stm32_usbphyc *usbphyc = usbphyc_phy->usbphyc;
+
+	usbphyc_phy->active = false;
+
+	return stm32_usbphyc_pll_disable(usbphyc);
+}
+
+static int stm32_usbphyc_phy_power_on(struct phy *phy)
+{
+	struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy);
+
+	if (usbphyc_phy->vbus)
+		return regulator_enable(usbphyc_phy->vbus);
+
+	return 0;
+}
+
+static int stm32_usbphyc_phy_power_off(struct phy *phy)
+{
+	struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy);
+
+	if (usbphyc_phy->vbus)
+		return regulator_disable(usbphyc_phy->vbus);
+
+	return 0;
+}
+
+static const struct phy_ops stm32_usbphyc_phy_ops = {
+	.init = stm32_usbphyc_phy_init,
+	.exit = stm32_usbphyc_phy_exit,
+	.power_on = stm32_usbphyc_phy_power_on,
+	.power_off = stm32_usbphyc_phy_power_off,
+	.owner = THIS_MODULE,
+};
+
+static int stm32_usbphyc_clk48_prepare(struct clk_hw *hw)
+{
+	struct stm32_usbphyc *usbphyc = container_of(hw, struct stm32_usbphyc, clk48_hw);
+
+	return stm32_usbphyc_pll_enable(usbphyc);
+}
+
+static void stm32_usbphyc_clk48_unprepare(struct clk_hw *hw)
+{
+	struct stm32_usbphyc *usbphyc = container_of(hw, struct stm32_usbphyc, clk48_hw);
+
+	stm32_usbphyc_pll_disable(usbphyc);
+}
+
+static unsigned long stm32_usbphyc_clk48_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
+{
+	return 48000000;
+}
+
+static const struct clk_ops usbphyc_clk48_ops = {
+	.prepare = stm32_usbphyc_clk48_prepare,
+	.unprepare = stm32_usbphyc_clk48_unprepare,
+	.recalc_rate = stm32_usbphyc_clk48_recalc_rate,
+};
+
+static void stm32_usbphyc_clk48_unregister(void *data)
+{
+	struct stm32_usbphyc *usbphyc = data;
+
+	of_clk_del_provider(usbphyc->dev->of_node);
+	clk_hw_unregister(&usbphyc->clk48_hw);
+}
+
+static int stm32_usbphyc_clk48_register(struct stm32_usbphyc *usbphyc)
+{
+	struct device_node *node = usbphyc->dev->of_node;
+	struct clk_init_data init = { };
+	int ret = 0;
+
+	init.name = "ck_usbo_48m";
+	init.ops = &usbphyc_clk48_ops;
+
+	usbphyc->clk48_hw.init = &init;
+
+	ret = clk_hw_register(usbphyc->dev, &usbphyc->clk48_hw);
+	if (ret)
+		return ret;
+
+	ret = of_clk_add_hw_provider(node, of_clk_hw_simple_get, &usbphyc->clk48_hw);
+	if (ret)
+		clk_hw_unregister(&usbphyc->clk48_hw);
+
+	return ret;
+}
+
+static void stm32_usbphyc_phy_tuning(struct stm32_usbphyc *usbphyc,
+				     struct device_node *np, u32 index)
+{
+	struct stm32_usbphyc_phy *usbphyc_phy = usbphyc->phys[index];
+	u32 reg = STM32_USBPHYC_TUNE(index);
+	u32 otpcomp, val;
+	int ret;
+
+	/* Backup OTP compensation code */
+	otpcomp = FIELD_GET(OTPCOMP, readl_relaxed(usbphyc->base + reg));
+
+	ret = of_property_read_u32(np, "st,current-boost-microamp", &val);
+	if (ret != -EINVAL) {
+		if (!ret && (val == BOOST_1000_UA || val == BOOST_2000_UA)) {
+			val = (val == BOOST_2000_UA) ? 1 : 0;
+			usbphyc_phy->tune |= INCURREN | FIELD_PREP(INCURRINT, val);
+		} else {
+			dev_warn(usbphyc->dev, "phy%d: invalid st,current-boost-microamp\n", index);
+		}
+	}
+
+	if (!of_property_read_bool(np, "st,no-lsfs-fb-cap"))
+		usbphyc_phy->tune |= LFSCAPEN;
+
+	if (of_property_read_bool(np, "st,decrease-hs-slew-rate"))
+		usbphyc_phy->tune |= HSDRVSLEW;
+
+	ret = of_property_read_u32(np, "st,tune-hs-dc-level", &val);
+	if (ret != -EINVAL) {
+		if (!ret && val < DC_MAX) {
+			if (val == DC_MINUS_5_TO_7_MV) {/* Decreases HS driver DC level */
+				usbphyc_phy->tune |= HSDRVDCCUR;
+			} else if (val > 0) {		/* Increases HS driver DC level */
+				val = (val == DC_PLUS_10_TO_14_MV) ? 1 : 0;
+				usbphyc_phy->tune |= HSDRVCURINCR | FIELD_PREP(HSDRVDCLEV, val);
+			}
+		} else {
+			dev_warn(usbphyc->dev, "phy%d: invalid st,tune-hs-dc-level\n", index);
+		}
+	}
+
+	if (of_property_read_bool(np, "st,enable-fs-rftime-tuning"))
+		usbphyc_phy->tune |= FSDRVRFADJ;
+
+	if (of_property_read_bool(np, "st,enable-hs-rftime-reduction"))
+		usbphyc_phy->tune |= HSDRVRFRED;
+
+	ret = of_property_read_u32(np, "st,trim-hs-current", &val);
+	if (ret != -EINVAL) {
+		if (!ret && val < CUR_MAX)
+			usbphyc_phy->tune |= FIELD_PREP(HSDRVCHKITRM, val);
+		else
+			dev_warn(usbphyc->dev, "phy%d: invalid st,trim-hs-current\n", index);
+	}
+
+	ret = of_property_read_u32(np, "st,trim-hs-impedance", &val);
+	if (ret != -EINVAL) {
+		if (!ret && val < IMP_MAX)
+			usbphyc_phy->tune |= FIELD_PREP(HSDRVCHKZTRM, val);
+		else
+			dev_warn(usbphyc->dev, "phy%d: invalid st,trim-hs-impedance\n", index);
+	}
+
+	ret = of_property_read_u32(np, "st,tune-squelch-level", &val);
+	if (ret != -EINVAL) {
+		if (!ret && val < SQLCH_MAX)
+			usbphyc_phy->tune |= FIELD_PREP(SQLCHCTL, val);
+		else
+			dev_warn(usbphyc->dev, "phy%d: invalid st,tune-squelch\n", index);
+	}
+
+	if (of_property_read_bool(np, "st,enable-hs-rx-gain-eq"))
+		usbphyc_phy->tune |= HDRXGNEQEN;
+
+	ret = of_property_read_u32(np, "st,tune-hs-rx-offset", &val);
+	if (ret != -EINVAL) {
+		if (!ret && val < RX_OFFSET_MAX)
+			usbphyc_phy->tune |= FIELD_PREP(HSRXOFF, val);
+		else
+			dev_warn(usbphyc->dev, "phy%d: invalid st,tune-hs-rx-offset\n", index);
+	}
+
+	if (of_property_read_bool(np, "st,no-hs-ftime-ctrl"))
+		usbphyc_phy->tune |= HSFALLPREEM;
+
+	if (!of_property_read_bool(np, "st,no-lsfs-sc"))
+		usbphyc_phy->tune |= SHTCCTCTLPROT;
+
+	if (of_property_read_bool(np, "st,enable-hs-tx-staggering"))
+		usbphyc_phy->tune |= STAGSEL;
+
+	/* Restore OTP compensation code */
+	usbphyc_phy->tune |= FIELD_PREP(OTPCOMP, otpcomp);
+
+	/*
+	 * By default, if no st,xxx tuning property is used, usbphyc_phy->tune is equal to
+	 * STM32_USBPHYC_TUNE reset value (LFSCAPEN | SHTCCTCTLPROT | OTPCOMP).
+	 */
+	writel_relaxed(usbphyc_phy->tune, usbphyc->base + reg);
+}
+
+static void stm32_usbphyc_switch_setup(struct stm32_usbphyc *usbphyc,
+				       u32 utmi_switch)
+{
+	if (!utmi_switch)
+		stm32_usbphyc_clr_bits(usbphyc->base + STM32_USBPHYC_MISC,
+				       SWITHOST);
+	else
+		stm32_usbphyc_set_bits(usbphyc->base + STM32_USBPHYC_MISC,
+				       SWITHOST);
+	usbphyc->switch_setup = utmi_switch;
+}
+
+static struct phy *stm32_usbphyc_of_xlate(struct device *dev,
+					  const struct of_phandle_args *args)
+{
+	struct stm32_usbphyc *usbphyc = dev_get_drvdata(dev);
+	struct stm32_usbphyc_phy *usbphyc_phy = NULL;
+	struct device_node *phynode = args->np;
+	int port = 0;
+
+	for (port = 0; port < usbphyc->nphys; port++) {
+		if (phynode == usbphyc->phys[port]->phy->dev.of_node) {
+			usbphyc_phy = usbphyc->phys[port];
+			break;
+		}
+	}
+	if (!usbphyc_phy) {
+		dev_err(dev, "failed to find phy\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	if (((usbphyc_phy->index == 0) && (args->args_count != 0)) ||
+	    ((usbphyc_phy->index == 1) && (args->args_count != 1))) {
+		dev_err(dev, "invalid number of cells for phy port%d\n",
+			usbphyc_phy->index);
+		return ERR_PTR(-EINVAL);
+	}
+
+	/* Configure the UTMI switch for PHY port#2 */
+	if (usbphyc_phy->index == 1) {
+		if (usbphyc->switch_setup < 0) {
+			stm32_usbphyc_switch_setup(usbphyc, args->args[0]);
+		} else {
+			if (args->args[0] != usbphyc->switch_setup) {
+				dev_err(dev, "phy port1 already used\n");
+				return ERR_PTR(-EBUSY);
+			}
+		}
+	}
+
+	return usbphyc_phy->phy;
+}
+
+static int stm32_usbphyc_probe(struct platform_device *pdev)
+{
+	struct stm32_usbphyc *usbphyc;
+	struct device *dev = &pdev->dev;
+	struct device_node *child, *np = dev->of_node;
+	struct phy_provider *phy_provider;
+	u32 pllen, version;
+	int ret, port = 0;
+
+	usbphyc = devm_kzalloc(dev, sizeof(*usbphyc), GFP_KERNEL);
+	if (!usbphyc)
+		return -ENOMEM;
+	usbphyc->dev = dev;
+	dev_set_drvdata(dev, usbphyc);
+
+	usbphyc->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(usbphyc->base))
+		return PTR_ERR(usbphyc->base);
+
+	usbphyc->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(usbphyc->clk))
+		return dev_err_probe(dev, PTR_ERR(usbphyc->clk), "clk get_failed\n");
+
+	ret = clk_prepare_enable(usbphyc->clk);
+	if (ret) {
+		dev_err(dev, "clk enable failed: %d\n", ret);
+		return ret;
+	}
+
+	usbphyc->rst = devm_reset_control_get(dev, NULL);
+	if (!IS_ERR(usbphyc->rst)) {
+		reset_control_assert(usbphyc->rst);
+		udelay(2);
+		reset_control_deassert(usbphyc->rst);
+	} else {
+		ret = PTR_ERR(usbphyc->rst);
+		if (ret == -EPROBE_DEFER)
+			goto clk_disable;
+
+		stm32_usbphyc_clr_bits(usbphyc->base + STM32_USBPHYC_PLL, PLLEN);
+	}
+
+	/*
+	 * Wait for minimum width of powerdown pulse (ENABLE = Low):
+	 * we have to ensure the PLL is disabled before phys initialization.
+	 */
+	if (readl_relaxed_poll_timeout(usbphyc->base + STM32_USBPHYC_PLL,
+				       pllen, !(pllen & PLLEN), 5, 50)) {
+		dev_warn(usbphyc->dev, "PLL not reset\n");
+		ret = -EPROBE_DEFER;
+		goto clk_disable;
+	}
+
+	usbphyc->switch_setup = -EINVAL;
+	usbphyc->nphys = of_get_child_count(np);
+	usbphyc->phys = devm_kcalloc(dev, usbphyc->nphys,
+				     sizeof(*usbphyc->phys), GFP_KERNEL);
+	if (!usbphyc->phys) {
+		ret = -ENOMEM;
+		goto clk_disable;
+	}
+
+	usbphyc->vdda1v1 = devm_regulator_get(dev, "vdda1v1");
+	if (IS_ERR(usbphyc->vdda1v1)) {
+		ret = dev_err_probe(dev, PTR_ERR(usbphyc->vdda1v1),
+				    "failed to get vdda1v1 supply\n");
+		goto clk_disable;
+	}
+
+	usbphyc->vdda1v8 = devm_regulator_get(dev, "vdda1v8");
+	if (IS_ERR(usbphyc->vdda1v8)) {
+		ret = dev_err_probe(dev, PTR_ERR(usbphyc->vdda1v8),
+				    "failed to get vdda1v8 supply\n");
+		goto clk_disable;
+	}
+
+	for_each_child_of_node(np, child) {
+		struct stm32_usbphyc_phy *usbphyc_phy;
+		struct phy *phy;
+		u32 index;
+
+		phy = devm_phy_create(dev, child, &stm32_usbphyc_phy_ops);
+		if (IS_ERR(phy)) {
+			ret = PTR_ERR(phy);
+			if (ret != -EPROBE_DEFER)
+				dev_err(dev, "failed to create phy%d: %d\n",
+					port, ret);
+			goto put_child;
+		}
+
+		usbphyc_phy = devm_kzalloc(dev, sizeof(*usbphyc_phy),
+					   GFP_KERNEL);
+		if (!usbphyc_phy) {
+			ret = -ENOMEM;
+			goto put_child;
+		}
+
+		ret = of_property_read_u32(child, "reg", &index);
+		if (ret || index >= usbphyc->nphys) {
+			dev_err(&phy->dev, "invalid reg property: %d\n", ret);
+			if (!ret)
+				ret = -EINVAL;
+			goto put_child;
+		}
+
+		usbphyc->phys[port] = usbphyc_phy;
+		phy_set_bus_width(phy, 8);
+		phy_set_drvdata(phy, usbphyc_phy);
+
+		usbphyc->phys[port]->phy = phy;
+		usbphyc->phys[port]->usbphyc = usbphyc;
+		usbphyc->phys[port]->index = index;
+		usbphyc->phys[port]->active = false;
+
+		usbphyc->phys[port]->vbus = devm_regulator_get_optional(&phy->dev, "vbus");
+		if (IS_ERR(usbphyc->phys[port]->vbus)) {
+			ret = PTR_ERR(usbphyc->phys[port]->vbus);
+			if (ret == -EPROBE_DEFER)
+				goto put_child;
+			usbphyc->phys[port]->vbus = NULL;
+		}
+
+		/* Configure phy tuning */
+		stm32_usbphyc_phy_tuning(usbphyc, child, index);
+
+		port++;
+	}
+
+	phy_provider = devm_of_phy_provider_register(dev,
+						     stm32_usbphyc_of_xlate);
+	if (IS_ERR(phy_provider)) {
+		ret = PTR_ERR(phy_provider);
+		dev_err(dev, "failed to register phy provider: %d\n", ret);
+		goto clk_disable;
+	}
+
+	ret = stm32_usbphyc_clk48_register(usbphyc);
+	if (ret) {
+		dev_err(dev, "failed to register ck_usbo_48m clock: %d\n", ret);
+		goto clk_disable;
+	}
+
+	version = readl_relaxed(usbphyc->base + STM32_USBPHYC_VERSION);
+	dev_dbg(dev, "registered rev: %lu.%lu\n",
+		FIELD_GET(MAJREV, version), FIELD_GET(MINREV, version));
+
+	return 0;
+
+put_child:
+	of_node_put(child);
+clk_disable:
+	clk_disable_unprepare(usbphyc->clk);
+
+	return ret;
+}
+
+static void stm32_usbphyc_remove(struct platform_device *pdev)
+{
+	struct stm32_usbphyc *usbphyc = dev_get_drvdata(&pdev->dev);
+	int port;
+
+	/* Ensure PHYs are not active, to allow PLL disabling */
+	for (port = 0; port < usbphyc->nphys; port++)
+		if (usbphyc->phys[port]->active)
+			stm32_usbphyc_phy_exit(usbphyc->phys[port]->phy);
+
+	stm32_usbphyc_clk48_unregister(usbphyc);
+
+	clk_disable_unprepare(usbphyc->clk);
+}
+
+static int __maybe_unused stm32_usbphyc_resume(struct device *dev)
+{
+	struct stm32_usbphyc *usbphyc = dev_get_drvdata(dev);
+	struct stm32_usbphyc_phy *usbphyc_phy;
+	int port;
+
+	if (usbphyc->switch_setup >= 0)
+		stm32_usbphyc_switch_setup(usbphyc, usbphyc->switch_setup);
+
+	for (port = 0; port < usbphyc->nphys; port++) {
+		usbphyc_phy = usbphyc->phys[port];
+		writel_relaxed(usbphyc_phy->tune, usbphyc->base + STM32_USBPHYC_TUNE(port));
+	}
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(stm32_usbphyc_pm_ops, NULL, stm32_usbphyc_resume);
+
+static const struct of_device_id stm32_usbphyc_of_match[] = {
+	{ .compatible = "st,stm32mp1-usbphyc", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, stm32_usbphyc_of_match);
+
+static struct platform_driver stm32_usbphyc_driver = {
+	.probe = stm32_usbphyc_probe,
+	.remove = stm32_usbphyc_remove,
+	.driver = {
+		.of_match_table = stm32_usbphyc_of_match,
+		.name = "stm32-usbphyc",
+		.pm = &stm32_usbphyc_pm_ops,
+	}
+};
+module_platform_driver(stm32_usbphyc_driver);
+
+MODULE_DESCRIPTION("STMicroelectronics STM32 USBPHYC driver");
+MODULE_AUTHOR("Amelie Delaunay <amelie.delaunay@st.com>");
+MODULE_LICENSE("GPL v2");