Resguardo inicial

linux-7.2.3/samples/vfio-mdev/Makefile

@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_SAMPLE_VFIO_MDEV_MTTY) += mtty.o
+obj-$(CONFIG_SAMPLE_VFIO_MDEV_MDPY) += mdpy.o
+obj-$(CONFIG_SAMPLE_VFIO_MDEV_MDPY_FB) += mdpy-fb.o
+obj-$(CONFIG_SAMPLE_VFIO_MDEV_MBOCHS) += mbochs.o

linux-7.2.3/samples/vfio-mdev/README.rst

@@ -0,0 +1,100 @@
+Using the mtty vfio-mdev sample code
+====================================
+
+mtty is a sample vfio-mdev driver that demonstrates how to use the mediated
+device framework.
+
+The sample driver creates an mdev device that simulates a serial port over a PCI
+card.
+
+1. Build and load the mtty.ko module.
+
+   This step creates a dummy device, /sys/devices/virtual/mtty/mtty/
+
+   Files in this device directory in sysfs are similar to the following::
+
+     # tree /sys/devices/virtual/mtty/mtty/
+        /sys/devices/virtual/mtty/mtty/
+        |-- mdev_supported_types
+        |   |-- mtty-1
+        |   |   |-- available_instances
+        |   |   |-- create
+        |   |   |-- device_api
+        |   |   |-- devices
+        |   |   `-- name
+        |   `-- mtty-2
+        |       |-- available_instances
+        |       |-- create
+        |       |-- device_api
+        |       |-- devices
+        |       `-- name
+        |-- mtty_dev
+        |   `-- sample_mtty_dev
+        |-- power
+        |   |-- autosuspend_delay_ms
+        |   |-- control
+        |   |-- runtime_active_time
+        |   |-- runtime_status
+        |   `-- runtime_suspended_time
+        |-- subsystem -> ../../../../class/mtty
+        `-- uevent
+
+2. Create a mediated device by using the dummy device that you created in the
+   previous step::
+
+     # echo "83b8f4f2-509f-382f-3c1e-e6bfe0fa1001" >	\
+              /sys/devices/virtual/mtty/mtty/mdev_supported_types/mtty-2/create
+
+3. Add parameters to qemu-kvm::
+
+     -device vfio-pci,\
+      sysfsdev=/sys/bus/mdev/devices/83b8f4f2-509f-382f-3c1e-e6bfe0fa1001
+
+4. Boot the VM.
+
+   In the Linux guest VM, with no hardware on the host, the device appears
+   as  follows::
+
+     # lspci -s 00:05.0 -xxvv
+     00:05.0 Serial controller: Device 4348:3253 (rev 10) (prog-if 02 [16550])
+             Subsystem: Device 4348:3253
+             Physical Slot: 5
+             Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
+     Stepping- SERR- FastB2B- DisINTx-
+             Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
+     <TAbort- <MAbort- >SERR- <PERR- INTx-
+             Interrupt: pin A routed to IRQ 10
+             Region 0: I/O ports at c150 [size=8]
+             Region 1: I/O ports at c158 [size=8]
+             Kernel driver in use: serial
+     00: 48 43 53 32 01 00 00 02 10 02 00 07 00 00 00 00
+     10: 51 c1 00 00 59 c1 00 00 00 00 00 00 00 00 00 00
+     20: 00 00 00 00 00 00 00 00 00 00 00 00 48 43 53 32
+     30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00
+
+     In the Linux guest VM, dmesg output for the device is as follows:
+
+     serial 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, high) -> IRQ 10
+     0000:00:05.0: ttyS1 at I/O 0xc150 (irq = 10) is a 16550A
+     0000:00:05.0: ttyS2 at I/O 0xc158 (irq = 10) is a 16550A
+
+
+5. In the Linux guest VM, check the serial ports::
+
+     # setserial -g /dev/ttyS*
+     /dev/ttyS0, UART: 16550A, Port: 0x03f8, IRQ: 4
+     /dev/ttyS1, UART: 16550A, Port: 0xc150, IRQ: 10
+     /dev/ttyS2, UART: 16550A, Port: 0xc158, IRQ: 10
+
+6. Using minicom or any terminal emulation program, open port /dev/ttyS1 or
+   /dev/ttyS2 with hardware flow control disabled.
+
+7. Type data on the minicom terminal or send data to the terminal emulation
+   program and read the data.
+
+   Data is loop backed from hosts mtty driver.
+
+8. Destroy the mediated device that you created::
+
+     # echo 1 > /sys/bus/mdev/devices/83b8f4f2-509f-382f-3c1e-e6bfe0fa1001/remove
+

linux-7.2.3/samples/vfio-mdev/mdpy-defs.h

@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Simple pci display device.
+ *
+ * Framebuffer memory is pci bar 0.
+ * Configuration (read-only) is in pci config space.
+ * Format field uses drm fourcc codes.
+ * ATM only DRM_FORMAT_XRGB8888 is supported.
+ */
+
+/* pci ids */
+#define MDPY_PCI_VENDOR_ID	PCI_VENDOR_ID_REDHAT
+#define MDPY_PCI_DEVICE_ID	0x000f
+#define MDPY_PCI_SUBVENDOR_ID	PCI_SUBVENDOR_ID_REDHAT_QUMRANET
+#define MDPY_PCI_SUBDEVICE_ID	PCI_SUBDEVICE_ID_QEMU
+
+/* pci cfg space offsets for fb config (dword) */
+#define MDPY_VENDORCAP_OFFSET   0x40
+#define MDPY_VENDORCAP_SIZE     0x10
+#define MDPY_FORMAT_OFFSET	(MDPY_VENDORCAP_OFFSET + 0x04)
+#define MDPY_WIDTH_OFFSET	(MDPY_VENDORCAP_OFFSET + 0x08)
+#define MDPY_HEIGHT_OFFSET	(MDPY_VENDORCAP_OFFSET + 0x0c)

linux-7.2.3/samples/vfio-mdev/mdpy-fb.c

@@ -0,0 +1,233 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Framebuffer driver for mdpy (mediated virtual pci display device).
+ *
+ * See mdpy-defs.h for device specs
+ *
+ *   (c) Gerd Hoffmann <kraxel@redhat.com>
+ *
+ * Using some code snippets from simplefb and cirrusfb.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ */
+#include <linux/errno.h>
+#include <linux/fb.h>
+#include <linux/io.h>
+#include <linux/pci.h>
+#include <linux/module.h>
+#include <drm/drm_fourcc.h>
+#include "mdpy-defs.h"
+
+static const struct fb_fix_screeninfo mdpy_fb_fix = {
+	.id		= "mdpy-fb",
+	.type		= FB_TYPE_PACKED_PIXELS,
+	.visual		= FB_VISUAL_TRUECOLOR,
+	.accel		= FB_ACCEL_NONE,
+};
+
+static const struct fb_var_screeninfo mdpy_fb_var = {
+	.height		= -1,
+	.width		= -1,
+	.activate	= FB_ACTIVATE_NOW,
+	.vmode		= FB_VMODE_NONINTERLACED,
+
+	.bits_per_pixel = 32,
+	.transp.offset	= 24,
+	.red.offset	= 16,
+	.green.offset	= 8,
+	.blue.offset	= 0,
+	.transp.length	= 8,
+	.red.length	= 8,
+	.green.length	= 8,
+	.blue.length	= 8,
+};
+
+#define PSEUDO_PALETTE_SIZE 16
+
+struct mdpy_fb_par {
+	u32 palette[PSEUDO_PALETTE_SIZE];
+};
+
+static int mdpy_fb_setcolreg(u_int regno, u_int red, u_int green, u_int blue,
+			      u_int transp, struct fb_info *info)
+{
+	u32 *pal = info->pseudo_palette;
+	u32 cr = red >> (16 - info->var.red.length);
+	u32 cg = green >> (16 - info->var.green.length);
+	u32 cb = blue >> (16 - info->var.blue.length);
+	u32 value, mask;
+
+	if (regno >= PSEUDO_PALETTE_SIZE)
+		return -EINVAL;
+
+	value = (cr << info->var.red.offset) |
+		(cg << info->var.green.offset) |
+		(cb << info->var.blue.offset);
+	if (info->var.transp.length > 0) {
+		mask = (1 << info->var.transp.length) - 1;
+		mask <<= info->var.transp.offset;
+		value |= mask;
+	}
+	pal[regno] = value;
+
+	return 0;
+}
+
+static void mdpy_fb_destroy(struct fb_info *info)
+{
+	if (info->screen_base)
+		iounmap(info->screen_base);
+}
+
+static const struct fb_ops mdpy_fb_ops = {
+	.owner		= THIS_MODULE,
+	FB_DEFAULT_IOMEM_OPS,
+	.fb_destroy	= mdpy_fb_destroy,
+	.fb_setcolreg	= mdpy_fb_setcolreg,
+};
+
+static int mdpy_fb_probe(struct pci_dev *pdev,
+			 const struct pci_device_id *ent)
+{
+	struct fb_info *info;
+	struct mdpy_fb_par *par;
+	u32 format, width, height;
+	int ret;
+
+	ret = pci_enable_device(pdev);
+	if (ret < 0)
+		return ret;
+
+	ret = pci_request_regions(pdev, "mdpy-fb");
+	if (ret < 0)
+		goto err_disable_dev;
+
+	pci_read_config_dword(pdev, MDPY_FORMAT_OFFSET, &format);
+	pci_read_config_dword(pdev, MDPY_WIDTH_OFFSET,	&width);
+	pci_read_config_dword(pdev, MDPY_HEIGHT_OFFSET, &height);
+	if (format != DRM_FORMAT_XRGB8888) {
+		pci_err(pdev, "format mismatch (0x%x != 0x%x)\n",
+			format, DRM_FORMAT_XRGB8888);
+		ret = -EINVAL;
+		goto err_release_regions;
+	}
+	if (width < 100	 || width > 10000) {
+		pci_err(pdev, "width (%d) out of range\n", width);
+		ret = -EINVAL;
+		goto err_release_regions;
+	}
+	if (height < 100 || height > 10000) {
+		pci_err(pdev, "height (%d) out of range\n", height);
+		ret = -EINVAL;
+		goto err_release_regions;
+	}
+	pci_info(pdev, "mdpy found: %dx%d framebuffer\n",
+		 width, height);
+
+	info = framebuffer_alloc(sizeof(struct mdpy_fb_par), &pdev->dev);
+	if (!info) {
+		ret = -ENOMEM;
+		goto err_release_regions;
+	}
+	pci_set_drvdata(pdev, info);
+	par = info->par;
+
+	info->fix = mdpy_fb_fix;
+	info->fix.smem_start = pci_resource_start(pdev, 0);
+	info->fix.smem_len = pci_resource_len(pdev, 0);
+	info->fix.line_length = width * 4;
+
+	info->var = mdpy_fb_var;
+	info->var.xres = width;
+	info->var.yres = height;
+	info->var.xres_virtual = width;
+	info->var.yres_virtual = height;
+
+	info->screen_size = info->fix.smem_len;
+	info->screen_base = ioremap(info->fix.smem_start,
+				    info->screen_size);
+	if (!info->screen_base) {
+		pci_err(pdev, "ioremap(pcibar) failed\n");
+		ret = -EIO;
+		goto err_release_fb;
+	}
+
+	info->fbops = &mdpy_fb_ops;
+	info->pseudo_palette = par->palette;
+
+	ret = register_framebuffer(info);
+	if (ret < 0) {
+		pci_err(pdev, "mdpy-fb device register failed: %d\n", ret);
+		goto err_unmap;
+	}
+
+	pci_info(pdev, "fb%d registered\n", info->node);
+	return 0;
+
+err_unmap:
+	iounmap(info->screen_base);
+
+err_release_fb:
+	framebuffer_release(info);
+
+err_release_regions:
+	pci_release_regions(pdev);
+
+err_disable_dev:
+	pci_disable_device(pdev);
+
+	return ret;
+}
+
+static void mdpy_fb_remove(struct pci_dev *pdev)
+{
+	struct fb_info *info = pci_get_drvdata(pdev);
+
+	unregister_framebuffer(info);
+	iounmap(info->screen_base);
+	framebuffer_release(info);
+	pci_release_regions(pdev);
+	pci_disable_device(pdev);
+}
+
+static struct pci_device_id mdpy_fb_pci_table[] = {
+	{
+		.vendor	   = MDPY_PCI_VENDOR_ID,
+		.device	   = MDPY_PCI_DEVICE_ID,
+		.subvendor = MDPY_PCI_SUBVENDOR_ID,
+		.subdevice = MDPY_PCI_SUBDEVICE_ID,
+	}, {
+		/* end of list */
+	}
+};
+
+static struct pci_driver mdpy_fb_pci_driver = {
+	.name		= "mdpy-fb",
+	.id_table	= mdpy_fb_pci_table,
+	.probe		= mdpy_fb_probe,
+	.remove		= mdpy_fb_remove,
+};
+
+static int __init mdpy_fb_init(void)
+{
+	int ret;
+
+	ret = pci_register_driver(&mdpy_fb_pci_driver);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+module_init(mdpy_fb_init);
+
+MODULE_DEVICE_TABLE(pci, mdpy_fb_pci_table);
+MODULE_DESCRIPTION("Framebuffer driver for mdpy (mediated virtual pci display device)");
+MODULE_LICENSE("GPL v2");

linux-7.2.3/samples/vfio-mdev/mdpy.c

@@ -0,0 +1,743 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Mediated virtual PCI display host device driver
+ *
+ * See mdpy-defs.h for device specs
+ *
+ *   (c) Gerd Hoffmann <kraxel@redhat.com>
+ *
+ * based on mtty driver which is:
+ *   Copyright (c) 2016, NVIDIA CORPORATION. All rights reserved.
+ *	 Author: Neo Jia <cjia@nvidia.com>
+ *		 Kirti Wankhede <kwankhede@nvidia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/vmalloc.h>
+#include <linux/cdev.h>
+#include <linux/vfio.h>
+#include <linux/iommu.h>
+#include <linux/sysfs.h>
+#include <linux/mdev.h>
+#include <linux/pci.h>
+#include <drm/drm_fourcc.h>
+#include "mdpy-defs.h"
+
+#define MDPY_NAME		"mdpy"
+#define MDPY_CLASS_NAME		"mdpy"
+
+#define MDPY_CONFIG_SPACE_SIZE	0xff
+#define MDPY_MEMORY_BAR_OFFSET	PAGE_SIZE
+#define MDPY_DISPLAY_REGION	16
+
+#define STORE_LE16(addr, val)	(*(u16 *)addr = val)
+#define STORE_LE32(addr, val)	(*(u32 *)addr = val)
+
+
+MODULE_DESCRIPTION("Mediated virtual PCI display host device driver");
+MODULE_LICENSE("GPL v2");
+
+#define MDPY_TYPE_1 "vga"
+#define MDPY_TYPE_2 "xga"
+#define MDPY_TYPE_3 "hd"
+
+static struct mdpy_type {
+	struct mdev_type type;
+	u32 format;
+	u32 bytepp;
+	u32 width;
+	u32 height;
+} mdpy_types[] = {
+	{
+		.type.sysfs_name 	= MDPY_TYPE_1,
+		.type.pretty_name	= MDPY_CLASS_NAME "-" MDPY_TYPE_1,
+		.format = DRM_FORMAT_XRGB8888,
+		.bytepp = 4,
+		.width	= 640,
+		.height = 480,
+	}, {
+		.type.sysfs_name 	= MDPY_TYPE_2,
+		.type.pretty_name	= MDPY_CLASS_NAME "-" MDPY_TYPE_2,
+		.format = DRM_FORMAT_XRGB8888,
+		.bytepp = 4,
+		.width	= 1024,
+		.height = 768,
+	}, {
+		.type.sysfs_name 	= MDPY_TYPE_3,
+		.type.pretty_name	= MDPY_CLASS_NAME "-" MDPY_TYPE_3,
+		.format = DRM_FORMAT_XRGB8888,
+		.bytepp = 4,
+		.width	= 1920,
+		.height = 1080,
+	},
+};
+
+static struct mdev_type *mdpy_mdev_types[] = {
+	&mdpy_types[0].type,
+	&mdpy_types[1].type,
+	&mdpy_types[2].type,
+};
+
+static dev_t		mdpy_devt;
+static const struct class mdpy_class = {
+	.name = MDPY_CLASS_NAME,
+};
+static struct cdev	mdpy_cdev;
+static struct device	mdpy_dev;
+static struct mdev_parent mdpy_parent;
+static const struct vfio_device_ops mdpy_dev_ops;
+
+/* State of each mdev device */
+struct mdev_state {
+	struct vfio_device vdev;
+	u8 *vconfig;
+	u32 bar_mask;
+	struct mutex ops_lock;
+	struct mdev_device *mdev;
+	struct vfio_device_info dev_info;
+
+	const struct mdpy_type *type;
+	u32 memsize;
+	void *memblk;
+};
+
+static void mdpy_create_config_space(struct mdev_state *mdev_state)
+{
+	STORE_LE16((u16 *) &mdev_state->vconfig[PCI_VENDOR_ID],
+		   MDPY_PCI_VENDOR_ID);
+	STORE_LE16((u16 *) &mdev_state->vconfig[PCI_DEVICE_ID],
+		   MDPY_PCI_DEVICE_ID);
+	STORE_LE16((u16 *) &mdev_state->vconfig[PCI_SUBSYSTEM_VENDOR_ID],
+		   MDPY_PCI_SUBVENDOR_ID);
+	STORE_LE16((u16 *) &mdev_state->vconfig[PCI_SUBSYSTEM_ID],
+		   MDPY_PCI_SUBDEVICE_ID);
+
+	STORE_LE16((u16 *) &mdev_state->vconfig[PCI_COMMAND],
+		   PCI_COMMAND_IO | PCI_COMMAND_MEMORY);
+	STORE_LE16((u16 *) &mdev_state->vconfig[PCI_STATUS],
+		   PCI_STATUS_CAP_LIST);
+	STORE_LE16((u16 *) &mdev_state->vconfig[PCI_CLASS_DEVICE],
+		   PCI_CLASS_DISPLAY_OTHER);
+	mdev_state->vconfig[PCI_CLASS_REVISION] =  0x01;
+
+	STORE_LE32((u32 *) &mdev_state->vconfig[PCI_BASE_ADDRESS_0],
+		   PCI_BASE_ADDRESS_SPACE_MEMORY |
+		   PCI_BASE_ADDRESS_MEM_TYPE_32	 |
+		   PCI_BASE_ADDRESS_MEM_PREFETCH);
+	mdev_state->bar_mask = ~(mdev_state->memsize) + 1;
+
+	/* vendor specific capability for the config registers */
+	mdev_state->vconfig[PCI_CAPABILITY_LIST]       = MDPY_VENDORCAP_OFFSET;
+	mdev_state->vconfig[MDPY_VENDORCAP_OFFSET + 0] = 0x09; /* vendor cap */
+	mdev_state->vconfig[MDPY_VENDORCAP_OFFSET + 1] = 0x00; /* next ptr */
+	mdev_state->vconfig[MDPY_VENDORCAP_OFFSET + 2] = MDPY_VENDORCAP_SIZE;
+	STORE_LE32((u32 *) &mdev_state->vconfig[MDPY_FORMAT_OFFSET],
+		   mdev_state->type->format);
+	STORE_LE32((u32 *) &mdev_state->vconfig[MDPY_WIDTH_OFFSET],
+		   mdev_state->type->width);
+	STORE_LE32((u32 *) &mdev_state->vconfig[MDPY_HEIGHT_OFFSET],
+		   mdev_state->type->height);
+}
+
+static void handle_pci_cfg_write(struct mdev_state *mdev_state, u16 offset,
+				 char *buf, u32 count)
+{
+	struct device *dev = mdev_dev(mdev_state->mdev);
+	u32 cfg_addr;
+
+	switch (offset) {
+	case PCI_BASE_ADDRESS_0:
+		cfg_addr = *(u32 *)buf;
+
+		if (cfg_addr == 0xffffffff) {
+			cfg_addr = (cfg_addr & mdev_state->bar_mask);
+		} else {
+			cfg_addr &= PCI_BASE_ADDRESS_MEM_MASK;
+			if (cfg_addr)
+				dev_info(dev, "BAR0 @ 0x%x\n", cfg_addr);
+		}
+
+		cfg_addr |= (mdev_state->vconfig[offset] &
+			     ~PCI_BASE_ADDRESS_MEM_MASK);
+		STORE_LE32(&mdev_state->vconfig[offset], cfg_addr);
+		break;
+	}
+}
+
+static ssize_t mdev_access(struct mdev_state *mdev_state, char *buf,
+			   size_t count, loff_t pos, bool is_write)
+{
+	int ret = 0;
+
+	mutex_lock(&mdev_state->ops_lock);
+
+	if (pos < MDPY_CONFIG_SPACE_SIZE) {
+		if (is_write)
+			handle_pci_cfg_write(mdev_state, pos, buf, count);
+		else
+			memcpy(buf, (mdev_state->vconfig + pos), count);
+
+	} else if ((pos >= MDPY_MEMORY_BAR_OFFSET) &&
+		   (pos + count <=
+		    MDPY_MEMORY_BAR_OFFSET + mdev_state->memsize)) {
+		pos -= MDPY_MEMORY_BAR_OFFSET;
+		if (is_write)
+			memcpy(mdev_state->memblk, buf, count);
+		else
+			memcpy(buf, mdev_state->memblk, count);
+
+	} else {
+		dev_info(mdev_state->vdev.dev,
+			 "%s: %s @0x%llx (unhandled)\n", __func__,
+			 is_write ? "WR" : "RD", pos);
+		ret = -1;
+		goto accessfailed;
+	}
+
+	ret = count;
+
+
+accessfailed:
+	mutex_unlock(&mdev_state->ops_lock);
+
+	return ret;
+}
+
+static int mdpy_reset(struct mdev_state *mdev_state)
+{
+	u32 stride, i;
+
+	/* initialize with gray gradient */
+	stride = mdev_state->type->width * mdev_state->type->bytepp;
+	for (i = 0; i < mdev_state->type->height; i++)
+		memset(mdev_state->memblk + i * stride,
+		       i * 255 / mdev_state->type->height,
+		       stride);
+	return 0;
+}
+
+static int mdpy_init_dev(struct vfio_device *vdev)
+{
+	struct mdev_state *mdev_state =
+		container_of(vdev, struct mdev_state, vdev);
+	struct mdev_device *mdev = to_mdev_device(vdev->dev);
+	const struct mdpy_type *type =
+		container_of(mdev->type, struct mdpy_type, type);
+	u32 fbsize;
+	int ret = -ENOMEM;
+
+	mdev_state->vconfig = kzalloc(MDPY_CONFIG_SPACE_SIZE, GFP_KERNEL);
+	if (!mdev_state->vconfig)
+		return ret;
+
+	fbsize = roundup_pow_of_two(type->width * type->height * type->bytepp);
+
+	mdev_state->memblk = vmalloc_user(fbsize);
+	if (!mdev_state->memblk)
+		goto out_vconfig;
+
+	mutex_init(&mdev_state->ops_lock);
+	mdev_state->mdev = mdev;
+	mdev_state->type = type;
+	mdev_state->memsize = fbsize;
+	mdpy_create_config_space(mdev_state);
+	mdpy_reset(mdev_state);
+
+	dev_info(vdev->dev, "%s: %s (%dx%d)\n", __func__, type->type.pretty_name,
+		 type->width, type->height);
+	return 0;
+
+out_vconfig:
+	kfree(mdev_state->vconfig);
+	return ret;
+}
+
+static int mdpy_probe(struct mdev_device *mdev)
+{
+	struct mdev_state *mdev_state;
+	int ret;
+
+	mdev_state = vfio_alloc_device(mdev_state, vdev, &mdev->dev,
+				       &mdpy_dev_ops);
+	if (IS_ERR(mdev_state))
+		return PTR_ERR(mdev_state);
+
+	ret = vfio_register_emulated_iommu_dev(&mdev_state->vdev);
+	if (ret)
+		goto err_put_vdev;
+	dev_set_drvdata(&mdev->dev, mdev_state);
+	return 0;
+
+err_put_vdev:
+	vfio_put_device(&mdev_state->vdev);
+	return ret;
+}
+
+static void mdpy_release_dev(struct vfio_device *vdev)
+{
+	struct mdev_state *mdev_state =
+		container_of(vdev, struct mdev_state, vdev);
+
+	vfree(mdev_state->memblk);
+	kfree(mdev_state->vconfig);
+}
+
+static void mdpy_remove(struct mdev_device *mdev)
+{
+	struct mdev_state *mdev_state = dev_get_drvdata(&mdev->dev);
+
+	dev_info(&mdev->dev, "%s\n", __func__);
+
+	vfio_unregister_group_dev(&mdev_state->vdev);
+	vfio_put_device(&mdev_state->vdev);
+}
+
+static ssize_t mdpy_read(struct vfio_device *vdev, char __user *buf,
+			 size_t count, loff_t *ppos)
+{
+	struct mdev_state *mdev_state =
+		container_of(vdev, struct mdev_state, vdev);
+	unsigned int done = 0;
+	int ret;
+
+	while (count) {
+		size_t filled;
+
+		if (count >= 4 && !(*ppos % 4)) {
+			u32 val;
+
+			ret = mdev_access(mdev_state, (char *)&val, sizeof(val),
+					  *ppos, false);
+			if (ret <= 0)
+				goto read_err;
+
+			if (copy_to_user(buf, &val, sizeof(val)))
+				goto read_err;
+
+			filled = 4;
+		} else if (count >= 2 && !(*ppos % 2)) {
+			u16 val;
+
+			ret = mdev_access(mdev_state, (char *)&val, sizeof(val),
+					  *ppos, false);
+			if (ret <= 0)
+				goto read_err;
+
+			if (copy_to_user(buf, &val, sizeof(val)))
+				goto read_err;
+
+			filled = 2;
+		} else {
+			u8 val;
+
+			ret = mdev_access(mdev_state, (char *)&val, sizeof(val),
+					  *ppos, false);
+			if (ret <= 0)
+				goto read_err;
+
+			if (copy_to_user(buf, &val, sizeof(val)))
+				goto read_err;
+
+			filled = 1;
+		}
+
+		count -= filled;
+		done += filled;
+		*ppos += filled;
+		buf += filled;
+	}
+
+	return done;
+
+read_err:
+	return -EFAULT;
+}
+
+static ssize_t mdpy_write(struct vfio_device *vdev, const char __user *buf,
+			  size_t count, loff_t *ppos)
+{
+	struct mdev_state *mdev_state =
+		container_of(vdev, struct mdev_state, vdev);
+	unsigned int done = 0;
+	int ret;
+
+	while (count) {
+		size_t filled;
+
+		if (count >= 4 && !(*ppos % 4)) {
+			u32 val;
+
+			if (copy_from_user(&val, buf, sizeof(val)))
+				goto write_err;
+
+			ret = mdev_access(mdev_state, (char *)&val, sizeof(val),
+					  *ppos, true);
+			if (ret <= 0)
+				goto write_err;
+
+			filled = 4;
+		} else if (count >= 2 && !(*ppos % 2)) {
+			u16 val;
+
+			if (copy_from_user(&val, buf, sizeof(val)))
+				goto write_err;
+
+			ret = mdev_access(mdev_state, (char *)&val, sizeof(val),
+					  *ppos, true);
+			if (ret <= 0)
+				goto write_err;
+
+			filled = 2;
+		} else {
+			u8 val;
+
+			if (copy_from_user(&val, buf, sizeof(val)))
+				goto write_err;
+
+			ret = mdev_access(mdev_state, (char *)&val, sizeof(val),
+					  *ppos, true);
+			if (ret <= 0)
+				goto write_err;
+
+			filled = 1;
+		}
+		count -= filled;
+		done += filled;
+		*ppos += filled;
+		buf += filled;
+	}
+
+	return done;
+write_err:
+	return -EFAULT;
+}
+
+static int mdpy_mmap(struct vfio_device *vdev, struct vm_area_struct *vma)
+{
+	struct mdev_state *mdev_state =
+		container_of(vdev, struct mdev_state, vdev);
+
+	if (vma->vm_pgoff != MDPY_MEMORY_BAR_OFFSET >> PAGE_SHIFT)
+		return -EINVAL;
+	if (vma->vm_end < vma->vm_start)
+		return -EINVAL;
+	if (vma->vm_end - vma->vm_start > mdev_state->memsize)
+		return -EINVAL;
+	if ((vma->vm_flags & VM_SHARED) == 0)
+		return -EINVAL;
+
+	return remap_vmalloc_range(vma, mdev_state->memblk, 0);
+}
+
+static int mdpy_ioctl_get_region_info(struct vfio_device *vdev,
+				      struct vfio_region_info *region_info,
+				      struct vfio_info_cap *caps)
+{
+	struct mdev_state *mdev_state =
+		container_of(vdev, struct mdev_state, vdev);
+
+	if (region_info->index >= VFIO_PCI_NUM_REGIONS &&
+	    region_info->index != MDPY_DISPLAY_REGION)
+		return -EINVAL;
+
+	switch (region_info->index) {
+	case VFIO_PCI_CONFIG_REGION_INDEX:
+		region_info->offset = 0;
+		region_info->size   = MDPY_CONFIG_SPACE_SIZE;
+		region_info->flags  = (VFIO_REGION_INFO_FLAG_READ |
+				       VFIO_REGION_INFO_FLAG_WRITE);
+		break;
+	case VFIO_PCI_BAR0_REGION_INDEX:
+	case MDPY_DISPLAY_REGION:
+		region_info->offset = MDPY_MEMORY_BAR_OFFSET;
+		region_info->size   = mdev_state->memsize;
+		region_info->flags  = (VFIO_REGION_INFO_FLAG_READ  |
+				       VFIO_REGION_INFO_FLAG_WRITE |
+				       VFIO_REGION_INFO_FLAG_MMAP);
+		break;
+	default:
+		region_info->size   = 0;
+		region_info->offset = 0;
+		region_info->flags  = 0;
+	}
+
+	return 0;
+}
+
+static int mdpy_get_irq_info(struct vfio_irq_info *irq_info)
+{
+	irq_info->count = 0;
+	return 0;
+}
+
+static int mdpy_get_device_info(struct vfio_device_info *dev_info)
+{
+	dev_info->flags = VFIO_DEVICE_FLAGS_PCI;
+	dev_info->num_regions = VFIO_PCI_NUM_REGIONS;
+	dev_info->num_irqs = VFIO_PCI_NUM_IRQS;
+	return 0;
+}
+
+static int mdpy_query_gfx_plane(struct mdev_state *mdev_state,
+				struct vfio_device_gfx_plane_info *plane)
+{
+	if (plane->flags & VFIO_GFX_PLANE_TYPE_PROBE) {
+		if (plane->flags == (VFIO_GFX_PLANE_TYPE_PROBE |
+				     VFIO_GFX_PLANE_TYPE_REGION))
+			return 0;
+		return -EINVAL;
+	}
+
+	if (plane->flags != VFIO_GFX_PLANE_TYPE_REGION)
+		return -EINVAL;
+
+	plane->drm_format     = mdev_state->type->format;
+	plane->width	      = mdev_state->type->width;
+	plane->height	      = mdev_state->type->height;
+	plane->stride	      = (mdev_state->type->width *
+				 mdev_state->type->bytepp);
+	plane->size	      = mdev_state->memsize;
+	plane->region_index   = MDPY_DISPLAY_REGION;
+
+	/* unused */
+	plane->drm_format_mod = 0;
+	plane->x_pos	      = 0;
+	plane->y_pos	      = 0;
+	plane->x_hot	      = 0;
+	plane->y_hot	      = 0;
+
+	return 0;
+}
+
+static long mdpy_ioctl(struct vfio_device *vdev, unsigned int cmd,
+		       unsigned long arg)
+{
+	int ret = 0;
+	unsigned long minsz;
+	struct mdev_state *mdev_state =
+		container_of(vdev, struct mdev_state, vdev);
+
+	switch (cmd) {
+	case VFIO_DEVICE_GET_INFO:
+	{
+		struct vfio_device_info info;
+
+		minsz = offsetofend(struct vfio_device_info, num_irqs);
+
+		if (copy_from_user(&info, (void __user *)arg, minsz))
+			return -EFAULT;
+
+		if (info.argsz < minsz)
+			return -EINVAL;
+
+		ret = mdpy_get_device_info(&info);
+		if (ret)
+			return ret;
+
+		memcpy(&mdev_state->dev_info, &info, sizeof(info));
+
+		if (copy_to_user((void __user *)arg, &info, minsz))
+			return -EFAULT;
+
+		return 0;
+	}
+
+	case VFIO_DEVICE_GET_IRQ_INFO:
+	{
+		struct vfio_irq_info info;
+
+		minsz = offsetofend(struct vfio_irq_info, count);
+
+		if (copy_from_user(&info, (void __user *)arg, minsz))
+			return -EFAULT;
+
+		if ((info.argsz < minsz) ||
+		    (info.index >= mdev_state->dev_info.num_irqs))
+			return -EINVAL;
+
+		ret = mdpy_get_irq_info(&info);
+		if (ret)
+			return ret;
+
+		if (copy_to_user((void __user *)arg, &info, minsz))
+			return -EFAULT;
+
+		return 0;
+	}
+
+	case VFIO_DEVICE_QUERY_GFX_PLANE:
+	{
+		struct vfio_device_gfx_plane_info plane = {};
+
+		minsz = offsetofend(struct vfio_device_gfx_plane_info,
+				    region_index);
+
+		if (copy_from_user(&plane, (void __user *)arg, minsz))
+			return -EFAULT;
+
+		if (plane.argsz < minsz)
+			return -EINVAL;
+
+		ret = mdpy_query_gfx_plane(mdev_state, &plane);
+		if (ret)
+			return ret;
+
+		if (copy_to_user((void __user *)arg, &plane, minsz))
+			return -EFAULT;
+
+		return 0;
+	}
+
+	case VFIO_DEVICE_SET_IRQS:
+		return -EINVAL;
+
+	case VFIO_DEVICE_RESET:
+		return mdpy_reset(mdev_state);
+	}
+	return -ENOTTY;
+}
+
+static ssize_t
+resolution_show(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	struct mdev_state *mdev_state = dev_get_drvdata(dev);
+
+	return sprintf(buf, "%dx%d\n",
+		       mdev_state->type->width,
+		       mdev_state->type->height);
+}
+static DEVICE_ATTR_RO(resolution);
+
+static struct attribute *mdev_dev_attrs[] = {
+	&dev_attr_resolution.attr,
+	NULL,
+};
+
+static const struct attribute_group mdev_dev_group = {
+	.name  = "vendor",
+	.attrs = mdev_dev_attrs,
+};
+
+static const struct attribute_group *mdev_dev_groups[] = {
+	&mdev_dev_group,
+	NULL,
+};
+
+static ssize_t mdpy_show_description(struct mdev_type *mtype, char *buf)
+{
+	struct mdpy_type *type = container_of(mtype, struct mdpy_type, type);
+
+	return sprintf(buf, "virtual display, %dx%d framebuffer\n",
+		       type->width, type->height);
+}
+
+static const struct vfio_device_ops mdpy_dev_ops = {
+	.init = mdpy_init_dev,
+	.release = mdpy_release_dev,
+	.read = mdpy_read,
+	.write = mdpy_write,
+	.ioctl = mdpy_ioctl,
+	.get_region_info_caps = mdpy_ioctl_get_region_info,
+	.mmap = mdpy_mmap,
+	.bind_iommufd	= vfio_iommufd_emulated_bind,
+	.unbind_iommufd	= vfio_iommufd_emulated_unbind,
+	.attach_ioas	= vfio_iommufd_emulated_attach_ioas,
+	.detach_ioas	= vfio_iommufd_emulated_detach_ioas,
+};
+
+static struct mdev_driver mdpy_driver = {
+	.device_api = VFIO_DEVICE_API_PCI_STRING,
+	.max_instances = 4,
+	.driver = {
+		.name = "mdpy",
+		.owner = THIS_MODULE,
+		.mod_name = KBUILD_MODNAME,
+		.dev_groups = mdev_dev_groups,
+	},
+	.probe = mdpy_probe,
+	.remove	= mdpy_remove,
+	.show_description = mdpy_show_description,
+};
+
+static const struct file_operations vd_fops = {
+	.owner		= THIS_MODULE,
+};
+
+static void mdpy_device_release(struct device *dev)
+{
+	/* nothing */
+}
+
+static int __init mdpy_dev_init(void)
+{
+	int ret = 0;
+
+	ret = alloc_chrdev_region(&mdpy_devt, 0, MINORMASK + 1, MDPY_NAME);
+	if (ret < 0) {
+		pr_err("Error: failed to register mdpy_dev, err: %d\n", ret);
+		return ret;
+	}
+	cdev_init(&mdpy_cdev, &vd_fops);
+	cdev_add(&mdpy_cdev, mdpy_devt, MINORMASK + 1);
+	pr_info("%s: major %d\n", __func__, MAJOR(mdpy_devt));
+
+	ret = mdev_register_driver(&mdpy_driver);
+	if (ret)
+		goto err_cdev;
+
+	ret = class_register(&mdpy_class);
+	if (ret)
+		goto err_driver;
+	mdpy_dev.class = &mdpy_class;
+	mdpy_dev.release = mdpy_device_release;
+	dev_set_name(&mdpy_dev, "%s", MDPY_NAME);
+
+	ret = device_register(&mdpy_dev);
+	if (ret)
+		goto err_put;
+
+	ret = mdev_register_parent(&mdpy_parent, &mdpy_dev, &mdpy_driver,
+				   mdpy_mdev_types,
+				   ARRAY_SIZE(mdpy_mdev_types));
+	if (ret)
+		goto err_device;
+
+	return 0;
+
+err_device:
+	device_del(&mdpy_dev);
+err_put:
+	put_device(&mdpy_dev);
+	class_unregister(&mdpy_class);
+err_driver:
+	mdev_unregister_driver(&mdpy_driver);
+err_cdev:
+	cdev_del(&mdpy_cdev);
+	unregister_chrdev_region(mdpy_devt, MINORMASK + 1);
+	return ret;
+}
+
+static void __exit mdpy_dev_exit(void)
+{
+	mdpy_dev.bus = NULL;
+	mdev_unregister_parent(&mdpy_parent);
+
+	device_unregister(&mdpy_dev);
+	mdev_unregister_driver(&mdpy_driver);
+	cdev_del(&mdpy_cdev);
+	unregister_chrdev_region(mdpy_devt, MINORMASK + 1);
+	class_unregister(&mdpy_class);
+}
+
+module_param_named(count, mdpy_driver.max_instances, int, 0444);
+MODULE_PARM_DESC(count, "number of " MDPY_NAME " devices");
+
+module_init(mdpy_dev_init)
+module_exit(mdpy_dev_exit)