363 lines
9.5 KiB
Devicetree
363 lines
9.5 KiB
Devicetree
// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
|
/*
|
|
* Device Tree Source for the RZ/T2H EVK board
|
|
*
|
|
* Copyright (C) 2025 Renesas Electronics Corp.
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "r9a09g077m44.dtsi"
|
|
|
|
/*
|
|
* SD0 can be connected to either eMMC (IC49) or SD card slot CN31
|
|
* Lets by default enable the eMMC, note we need the below SW settings
|
|
* for eMMC. Also ensure that CN78 pins 5 and 6 are connected with a jumper
|
|
* to provide the SD0 power supply when using eMMC.
|
|
* SW2[1] = ON; SW2[2] = ON
|
|
*
|
|
* To enable SD card and disable eMMC on SDHI0 disable the below macro
|
|
* and set the switch as follows. Also ensure that CN78 pins 3 and 4 are connected
|
|
* with a jumper to provide the SD0 power supply when using an SD card.
|
|
*
|
|
* SW2[1] = OFF; SW2[2] = ON.
|
|
*/
|
|
#define SD0_EMMC 1
|
|
#define SD0_SD (!SD0_EMMC)
|
|
|
|
/*
|
|
* P17_4 = SD1_CD; SW2[3] = ON
|
|
* P08_5 = SD1_PWEN; SW2[3] = ON
|
|
* P08_6 = SD1_IOVS; SW2[3] = ON; SW5[3] = OFF; SW5[4] = ON
|
|
* To enable proper operation in 1.8V modes, CN77 must have pins 2 and 3
|
|
* connected by the jumper. This connects SD1 power-supply control IC output
|
|
* back to VCC1833_7.
|
|
*/
|
|
#define SD1_MICRO_SD 1
|
|
|
|
/*
|
|
* USB Pin Configuration:
|
|
*
|
|
* This board is equipped with three USB connectors: Type-A (CN80), Mini-B
|
|
* (CN79), and Micro-AB (CN33). The RZ/T2H SoC has a single USB channel, so
|
|
* either the USB host interface or the USB function interface can be used,
|
|
* but not both simultaneously when using the CN79 and CN80 connectors.
|
|
*
|
|
* By default, the Type-A (CN80) and Mini-B (CN79) connectors are enabled.
|
|
* Configure the switches as follows:
|
|
* - P00_0 - P00_2 (control signals for USB power supply): SW1[5] = ON
|
|
* - USB_VBUSIN (used for USB function): SW7[7] = OFF; SW7[8] = ON
|
|
* - USB_VBUSEN (used for USB_HF_VBUSEN): SW7[9] = OFF; SW7[10] = ON
|
|
*
|
|
* To enable the Micro-AB (CN33) USB OTG connector, set the following macro
|
|
* to 1 and configure the switches as follows:
|
|
* - P00_0 - P00_2 (control signals for USB power supply): SW1[5] = ON
|
|
* - USB_VBUSIN (used for USB OTG): SW7[7] = ON; SW7[8] = OFF
|
|
* - USB_VBUSEN (used for USB_OTG_VBUSEN): SW7[9] = ON; SW7[10] = OFF
|
|
*/
|
|
#define USB_OTG 0
|
|
|
|
#include "rzt2h-n2h-evk-common.dtsi"
|
|
|
|
/ {
|
|
model = "Renesas RZ/T2H EVK Board based on r9a09g077m44";
|
|
compatible = "renesas,rzt2h-evk", "renesas,r9a09g077m44", "renesas,r9a09g077";
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
#if (!SD1_MICRO_SD)
|
|
/* SW2-3: OFF */
|
|
key-1 {
|
|
interrupts-extended = <&pinctrl RZT2H_GPIO(8, 6) IRQ_TYPE_EDGE_FALLING>;
|
|
linux,code = <KEY_1>;
|
|
label = "SW9";
|
|
wakeup-source;
|
|
debounce-interval = <20>;
|
|
};
|
|
#endif
|
|
|
|
key-2 {
|
|
interrupts-extended = <&pinctrl RZT2H_GPIO(0, 3) IRQ_TYPE_EDGE_FALLING>;
|
|
linux,code = <KEY_2>;
|
|
label = "SW10";
|
|
wakeup-source;
|
|
debounce-interval = <20>;
|
|
};
|
|
|
|
key-3 {
|
|
interrupts-extended = <&pinctrl RZT2H_GPIO(8, 7) IRQ_TYPE_EDGE_FALLING>;
|
|
linux,code = <KEY_3>;
|
|
label = "SW11";
|
|
wakeup-source;
|
|
debounce-interval = <20>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led-0 {
|
|
/* SW8-9: ON, SW8-10: OFF */
|
|
gpios = <&pinctrl RZT2H_GPIO(23, 1) GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_DEBUG;
|
|
function-enumerator = <0>;
|
|
};
|
|
|
|
led-1 {
|
|
/* SW5-1: OFF, SW5-2: ON */
|
|
gpios = <&pinctrl RZT2H_GPIO(32, 2) GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_DEBUG;
|
|
function-enumerator = <1>;
|
|
};
|
|
|
|
led-2 {
|
|
gpios = <&pinctrl RZT2H_GPIO(6, 7) GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_YELLOW>;
|
|
function = LED_FUNCTION_DEBUG;
|
|
function-enumerator = <2>;
|
|
};
|
|
|
|
#if (!SD1_MICRO_SD)
|
|
led-3 {
|
|
/* SW2-3: OFF */
|
|
gpios = <&pinctrl RZT2H_GPIO(8, 5) GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_RED>;
|
|
function = LED_FUNCTION_DEBUG;
|
|
function-enumerator = <3>;
|
|
};
|
|
#endif
|
|
|
|
led-4 {
|
|
/* SW8-3: ON, SW8-4: OFF */
|
|
gpios = <&pinctrl RZT2H_GPIO(18, 0) GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_DEBUG;
|
|
function-enumerator = <4>;
|
|
};
|
|
|
|
led-5 {
|
|
/* SW8-1: ON, SW8-2: OFF */
|
|
gpios = <&pinctrl RZT2H_GPIO(18, 1) GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_RED>;
|
|
function = LED_FUNCTION_DEBUG;
|
|
function-enumerator = <5>;
|
|
};
|
|
|
|
led-6 {
|
|
/* SW5-9: OFF, SW5-10: ON */
|
|
gpios = <&pinctrl RZT2H_GPIO(22, 7) GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_DEBUG;
|
|
function-enumerator = <6>;
|
|
};
|
|
|
|
led-7 {
|
|
/* SW5-7: OFF, SW5-8: ON */
|
|
gpios = <&pinctrl RZT2H_GPIO(23, 0) GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_DEBUG;
|
|
function-enumerator = <7>;
|
|
};
|
|
|
|
led-8 {
|
|
/* SW7-5: OFF, SW7-6: ON */
|
|
gpios = <&pinctrl RZT2H_GPIO(23, 5) GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_DEBUG;
|
|
function-enumerator = <8>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&adc2 {
|
|
status = "okay";
|
|
|
|
channel@0 {
|
|
reg = <0x0>;
|
|
};
|
|
|
|
channel@1 {
|
|
reg = <0x1>;
|
|
};
|
|
|
|
channel@2 {
|
|
reg = <0x2>;
|
|
};
|
|
|
|
channel@3 {
|
|
reg = <0x3>;
|
|
};
|
|
|
|
channel@4 {
|
|
reg = <0x4>;
|
|
};
|
|
|
|
channel@5 {
|
|
reg = <0x5>;
|
|
};
|
|
};
|
|
|
|
&canfd {
|
|
pinctrl-0 = <&can0_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
channel0 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&i2c0 {
|
|
pinctrl-0 = <&i2c0_pins>;
|
|
pinctrl-names = "default";
|
|
clock-frequency = <400000>;
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c1 {
|
|
pinctrl-0 = <&i2c1_pins>;
|
|
pinctrl-names = "default";
|
|
clock-frequency = <400000>;
|
|
status = "okay";
|
|
};
|
|
|
|
&mdio1_phy {
|
|
interrupts-extended = <&icu RZT2H_IRQ3 IRQ_TYPE_EDGE_FALLING>;
|
|
reset-gpios = <&pinctrl RZT2H_GPIO(32, 3) GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&mdio2_phy {
|
|
interrupts-extended = <&icu RZT2H_IRQ13 IRQ_TYPE_EDGE_FALLING>;
|
|
/*
|
|
* PHY2 Reset Configuration:
|
|
*
|
|
* SW6[1] OFF; SW6[2] ON; SW6[3] OFF - use pin P17_5 for GMAC_RESETOUT2#
|
|
*/
|
|
reset-gpios = <&pinctrl RZT2H_GPIO(17, 5) GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&pinctrl {
|
|
/*
|
|
* CAN0 Pin Configuration:
|
|
*
|
|
* SW7[1] OFF; SW7[2] ON - Use P24_4 as CANTX0.
|
|
* SW7[3] OFF; SW7[4] ON - Use P24_3 as CANRX0.
|
|
*/
|
|
can0_pins: can0-pins {
|
|
pinmux = <RZT2H_PORT_PINMUX(24, 3, 0x19)>, /* CANRX0 */
|
|
<RZT2H_PORT_PINMUX(24, 4, 0x19)>; /* CANTX0 */
|
|
};
|
|
|
|
/*
|
|
* GMAC1 Pin Configuration:
|
|
*
|
|
* SW2[8] ON - use pins P33_2-P33_7, P34_0-P34_5, P34_7 and
|
|
* P35_0-P35_2 for Ethernet port 3
|
|
*/
|
|
gmac1_pins: gmac1-pins {
|
|
pinmux = <RZT2H_PORT_PINMUX(33, 2, 0xf)>, /* ETH3_TXCLK */
|
|
<RZT2H_PORT_PINMUX(33, 3, 0xf)>, /* ETH3_TXD0 */
|
|
<RZT2H_PORT_PINMUX(33, 4, 0xf)>, /* ETH3_TXD1 */
|
|
<RZT2H_PORT_PINMUX(33, 5, 0xf)>, /* ETH3_TXD2 */
|
|
<RZT2H_PORT_PINMUX(33, 6, 0xf)>, /* ETH3_TXD3 */
|
|
<RZT2H_PORT_PINMUX(33, 7, 0xf)>, /* ETH3_TXEN */
|
|
<RZT2H_PORT_PINMUX(34, 0, 0xf)>, /* ETH3_RXCLK */
|
|
<RZT2H_PORT_PINMUX(34, 1, 0xf)>, /* ETH3_RXD0 */
|
|
<RZT2H_PORT_PINMUX(34, 2, 0xf)>, /* ETH3_RXD1 */
|
|
<RZT2H_PORT_PINMUX(34, 3, 0xf)>, /* ETH3_RXD2 */
|
|
<RZT2H_PORT_PINMUX(34, 4, 0xf)>, /* ETH3_RXD3 */
|
|
<RZT2H_PORT_PINMUX(34, 5, 0xf)>, /* ETH3_RXDV */
|
|
<RZT2H_PORT_PINMUX(34, 7, 0xf)>, /* ETH3_TXER */
|
|
<RZT2H_PORT_PINMUX(35, 0, 0xf)>, /* ETH3_RXER */
|
|
<RZT2H_PORT_PINMUX(35, 1, 0xf)>, /* ETH3_CRS */
|
|
<RZT2H_PORT_PINMUX(35, 2, 0xf)>, /* ETH3_COL */
|
|
<RZT2H_PORT_PINMUX(26, 1, 0x10)>, /* GMAC1_MDC */
|
|
<RZT2H_PORT_PINMUX(26, 2, 0x10)>, /* GMAC1_MDIO */
|
|
<RZT2H_PORT_PINMUX(34, 6, 0x2)>, /* ETH3_REFCLK */
|
|
<RZT2H_PORT_PINMUX(27, 2, 0x0)>; /* IRQ3 */
|
|
};
|
|
|
|
/*
|
|
* GMAC2 Pin Configuration:
|
|
*
|
|
* SW2[6] OFF - connect MDC/MDIO of Ethernet port 2 to GMAC2
|
|
* SW2[7] ON - use pins P29_1-P29_7, P30_0-P30_4, and P31_2-P31_5
|
|
* for Ethernet port 2
|
|
*/
|
|
gmac2_pins: gmac2-pins {
|
|
pinmux = <RZT2H_PORT_PINMUX(29, 1, 0xf)>, /* ETH2_TXCLK */
|
|
<RZT2H_PORT_PINMUX(29, 2, 0xf)>, /* ETH2_TXD0 */
|
|
<RZT2H_PORT_PINMUX(29, 3, 0xf)>, /* ETH2_TXD1 */
|
|
<RZT2H_PORT_PINMUX(29, 4, 0xf)>, /* ETH2_TXD2 */
|
|
<RZT2H_PORT_PINMUX(29, 5, 0xf)>, /* ETH2_TXD3 */
|
|
<RZT2H_PORT_PINMUX(29, 6, 0xf)>, /* ETH2_TXEN */
|
|
<RZT2H_PORT_PINMUX(29, 7, 0xf)>, /* ETH2_RXCLK */
|
|
<RZT2H_PORT_PINMUX(30, 0, 0xf)>, /* ETH2_RXD0 */
|
|
<RZT2H_PORT_PINMUX(30, 1, 0xf)>, /* ETH2_RXD1 */
|
|
<RZT2H_PORT_PINMUX(30, 2, 0xf)>, /* ETH2_RXD2 */
|
|
<RZT2H_PORT_PINMUX(30, 3, 0xf)>, /* ETH2_RXD3 */
|
|
<RZT2H_PORT_PINMUX(30, 4, 0xf)>, /* ETH2_RXDV */
|
|
<RZT2H_PORT_PINMUX(31, 2, 0xf)>, /* ETH2_TXER */
|
|
<RZT2H_PORT_PINMUX(31, 3, 0xf)>, /* ETH2_RXER */
|
|
<RZT2H_PORT_PINMUX(31, 4, 0xf)>, /* ETH2_CRS */
|
|
<RZT2H_PORT_PINMUX(31, 5, 0xf)>, /* ETH2_COL */
|
|
<RZT2H_PORT_PINMUX(30, 5, 0x10)>, /* GMAC2_MDC */
|
|
<RZT2H_PORT_PINMUX(30, 6, 0x10)>, /* GMAC2_MDIO */
|
|
<RZT2H_PORT_PINMUX(31, 0, 0x2)>, /* ETH2_REFCLK */
|
|
<RZT2H_PORT_PINMUX(31, 1, 0x0)>; /* IRQ13 */
|
|
};
|
|
|
|
/*
|
|
* I2C0 Pin Configuration:
|
|
* ------------------------
|
|
* Signal | Pin | SW6
|
|
* -------|---------|--------------
|
|
* SCL | P23_3 | 7: ON, 8: OFF
|
|
* SDA | P23_4 | 9: ON, 10: OFF
|
|
*/
|
|
i2c0_pins: i2c0-pins {
|
|
pinmux = <RZT2H_PORT_PINMUX(23, 3, 0x17)>,
|
|
<RZT2H_PORT_PINMUX(23, 4, 0x17)>;
|
|
};
|
|
|
|
i2c1_pins: i2c1-pins {
|
|
pinmux = <RZT2H_PORT_PINMUX(5, 0, 0x17)>, /* SDA */
|
|
<RZT2H_PORT_PINMUX(4, 7, 0x17)>; /* SCL */
|
|
};
|
|
|
|
#if USB_OTG
|
|
usb-exicen-hog {
|
|
gpio-hog;
|
|
gpios = <RZT2H_GPIO(0, 2) GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
line-name = "usb_exicen_a";
|
|
};
|
|
#endif
|
|
|
|
usb_pins: usb-pins {
|
|
pinmux = <RZT2H_PORT_PINMUX(0, 0, 0x13)>, /* VBUSEN */
|
|
<RZT2H_PORT_PINMUX(0, 1, 0x13)>; /* OVRCUR */
|
|
};
|
|
};
|
|
|
|
/*
|
|
* XSPI0 Pin Configuration:
|
|
* ------------------------
|
|
* Signal | Pin | SW5
|
|
* -----------|---------|---------------
|
|
* XSPI0_ECS | P07_5 | 5: OFF, 6: ON
|
|
*/
|
|
&xspi0_pins {
|
|
ecs-pins {
|
|
pinmux = <RZT2H_PORT_PINMUX(7, 5, 0x1c)>; /* XSPI0_ECS0 */
|
|
drive-strength-microamp = <2500>;
|
|
input-schmitt-disable;
|
|
slew-rate = <0>;
|
|
};
|
|
};
|