897 lines
18 KiB
Devicetree
897 lines
18 KiB
Devicetree
// SPDX-License-Identifier: BSD-3-Clause
|
|
/*
|
|
* Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
|
|
|
|
#include "monaco.dtsi"
|
|
#include "monaco-pmics.dtsi"
|
|
/ {
|
|
model = "Qualcomm Technologies, Inc. QCS8300 Ride";
|
|
compatible = "qcom,qcs8300-ride", "qcom,qcs8300";
|
|
chassis-type = "embedded";
|
|
|
|
aliases {
|
|
serial0 = &uart7;
|
|
mmc0 = &sdhc_1;
|
|
serial1 = &uart2;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
vreg_1p0: regulator-vreg-1p0 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "VREG_1P0";
|
|
|
|
regulator-min-microvolt = <1000000>;
|
|
regulator-max-microvolt = <1000000>;
|
|
|
|
vin-supply = <&vreg_1p8>;
|
|
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
vreg_1p8: regulator-vreg-1p8 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "VREG_1P8";
|
|
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
|
|
vin-supply = <&vreg_5p0>;
|
|
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
vreg_3p0: regulator-vreg-3p0 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "VREG_3P0";
|
|
|
|
regulator-min-microvolt = <3000000>;
|
|
regulator-max-microvolt = <3000000>;
|
|
|
|
vin-supply = <&vreg_12p0>;
|
|
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
vreg_5p0: regulator-vreg-5p0 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "VREG_5P0";
|
|
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
|
|
vin-supply = <&vreg_12p0>;
|
|
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
vreg_12p0: regulator-vreg-12p0 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "VREG_12P0";
|
|
|
|
regulator-min-microvolt = <12000000>;
|
|
regulator-max-microvolt = <12000000>;
|
|
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
dp0-connector {
|
|
compatible = "dp-connector";
|
|
label = "DP0";
|
|
type = "full-size";
|
|
|
|
port {
|
|
dp0_connector_in: endpoint {
|
|
remote-endpoint = <&mdss_dp0_out>;
|
|
};
|
|
};
|
|
};
|
|
|
|
dp-dsi0-connector {
|
|
compatible = "dp-connector";
|
|
label = "DSI0";
|
|
type = "full-size";
|
|
|
|
port {
|
|
dp_dsi0_connector_in: endpoint {
|
|
remote-endpoint = <&dsi2dp_bridge_out>;
|
|
};
|
|
};
|
|
};
|
|
|
|
vreg_conn_1p05: regulator-conn-1p05 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vreg_conn_1p05";
|
|
regulator-min-microvolt = <1050000>;
|
|
regulator-max-microvolt = <1050000>;
|
|
vin-supply = <&vreg_conn_1p8>;
|
|
};
|
|
|
|
vreg_conn_1p35: regulator-conn-1p35 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vreg_conn_1p35";
|
|
regulator-min-microvolt = <1350000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
vin-supply = <&vreg_conn_1p8>;
|
|
};
|
|
|
|
vreg_conn_1p8: regulator-conn-1p8 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vreg_conn_1p8";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
startup-delay-us = <4000>;
|
|
enable-active-high;
|
|
gpio = <&pmm8650au_1_gpios 4 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
vreg_conn_1p95: regulator-conn-1p95 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vreg_conn_1p95";
|
|
regulator-min-microvolt = <1950000>;
|
|
regulator-max-microvolt = <1950000>;
|
|
vin-supply = <&vreg_conn_1p8>;
|
|
};
|
|
|
|
vreg_conn_pa: regulator-conn-pa {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vreg_conn_pa";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
startup-delay-us = <4000>;
|
|
enable-active-high;
|
|
gpio = <&pmm8650au_1_gpios 6 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
regulator-usb2-vbus {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "USB2_VBUS";
|
|
gpio = <&pmm8650au_1_gpios 7 GPIO_ACTIVE_HIGH>;
|
|
pinctrl-0 = <&usb2_en>;
|
|
pinctrl-names = "default";
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
};
|
|
|
|
wcn6855-pmu {
|
|
compatible = "qcom,wcn6855-pmu";
|
|
|
|
pinctrl-0 = <&wlan_en_state>;
|
|
pinctrl-names = "default";
|
|
|
|
vddio-supply = <&vreg_conn_pa>;
|
|
vddaon-supply = <&vreg_conn_1p8>;
|
|
vddpmu-supply = <&vreg_conn_pa>;
|
|
vddpmumx-supply = <&vreg_conn_1p8>;
|
|
vddpmucx-supply = <&vreg_conn_pa>;
|
|
/* WLAN rails: 1.05/1.35/1.95V (nominal 0.95/1.30/1.90V) */
|
|
vddrfa0p95-supply = <&vreg_conn_1p05>;
|
|
vddrfa1p3-supply = <&vreg_conn_1p35>;
|
|
vddrfa1p9-supply = <&vreg_conn_1p95>;
|
|
vddpcie1p3-supply = <&vreg_conn_1p35>;
|
|
vddpcie1p9-supply = <&vreg_conn_1p95>;
|
|
|
|
bt-enable-gpios = <&tlmm 55 GPIO_ACTIVE_HIGH>;
|
|
wlan-enable-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
|
|
|
|
regulators {
|
|
vreg_pmu_rfa_cmn: ldo0 {
|
|
regulator-name = "vreg_pmu_rfa_cmn";
|
|
};
|
|
|
|
vreg_pmu_aon_0p59: ldo1 {
|
|
regulator-name = "vreg_pmu_aon_0p59";
|
|
};
|
|
|
|
vreg_pmu_wlcx_0p8: ldo2 {
|
|
regulator-name = "vreg_pmu_wlcx_0p8";
|
|
};
|
|
|
|
vreg_pmu_wlmx_0p85: ldo3 {
|
|
regulator-name = "vreg_pmu_wlmx_0p85";
|
|
};
|
|
|
|
vreg_pmu_btcmx_0p85: ldo4 {
|
|
regulator-name = "vreg_pmu_btcmx_0p85";
|
|
};
|
|
|
|
vreg_pmu_rfa_0p8: ldo5 {
|
|
regulator-name = "vreg_pmu_rfa_0p8";
|
|
};
|
|
|
|
vreg_pmu_rfa_1p2: ldo6 {
|
|
regulator-name = "vreg_pmu_rfa_1p2";
|
|
};
|
|
|
|
vreg_pmu_rfa_1p7: ldo7 {
|
|
regulator-name = "vreg_pmu_rfa_1p7";
|
|
};
|
|
|
|
vreg_pmu_pcie_0p9: ldo8 {
|
|
regulator-name = "vreg_pmu_pcie_0p9";
|
|
};
|
|
|
|
vreg_pmu_pcie_1p8: ldo9 {
|
|
regulator-name = "vreg_pmu_pcie_1p8";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&apps_rsc {
|
|
regulators-0 {
|
|
compatible = "qcom,pmm8654au-rpmh-regulators";
|
|
qcom,pmic-id = "a";
|
|
|
|
vreg_s4a: smps4 {
|
|
regulator-name = "vreg_s4a";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_s9a: smps9 {
|
|
regulator-name = "vreg_s9a";
|
|
regulator-min-microvolt = <1352000>;
|
|
regulator-max-microvolt = <1352000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l3a: ldo3 {
|
|
regulator-name = "vreg_l3a";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l4a: ldo4 {
|
|
regulator-name = "vreg_l4a";
|
|
regulator-min-microvolt = <880000>;
|
|
regulator-max-microvolt = <912000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l5a: ldo5 {
|
|
regulator-name = "vreg_l5a";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l6a: ldo6 {
|
|
regulator-name = "vreg_l6a";
|
|
regulator-min-microvolt = <880000>;
|
|
regulator-max-microvolt = <912000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l7a: ldo7 {
|
|
regulator-name = "vreg_l7a";
|
|
regulator-min-microvolt = <880000>;
|
|
regulator-max-microvolt = <912000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l8a: ldo8 {
|
|
regulator-name = "vreg_l8a";
|
|
regulator-min-microvolt = <2504000>;
|
|
regulator-max-microvolt = <2960000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l9a: ldo9 {
|
|
regulator-name = "vreg_l9a";
|
|
regulator-min-microvolt = <2970000>;
|
|
regulator-max-microvolt = <3072000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
};
|
|
|
|
regulators-1 {
|
|
compatible = "qcom,pmm8654au-rpmh-regulators";
|
|
qcom,pmic-id = "c";
|
|
|
|
vreg_s5c: smps5 {
|
|
regulator-name = "vreg_s5c";
|
|
regulator-min-microvolt = <1104000>;
|
|
regulator-max-microvolt = <1104000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l1c: ldo1 {
|
|
regulator-name = "vreg_l1c";
|
|
regulator-min-microvolt = <300000>;
|
|
regulator-max-microvolt = <500000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l2c: ldo2 {
|
|
regulator-name = "vreg_l2c";
|
|
regulator-min-microvolt = <900000>;
|
|
regulator-max-microvolt = <904000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l4c: ldo4 {
|
|
regulator-name = "vreg_l4c";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l6c: ldo6 {
|
|
regulator-name = "vreg_l6c";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l7c: ldo7 {
|
|
regulator-name = "vreg_l7c";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l8c: ldo8 {
|
|
regulator-name = "vreg_l8c";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l9c: ldo9 {
|
|
regulator-name = "vreg_l9c";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
regulator-allow-set-load;
|
|
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
|
RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet0 {
|
|
phy-mode = "2500base-x";
|
|
phy-handle = <&phy0>;
|
|
|
|
pinctrl-0 = <ðernet0_default>;
|
|
pinctrl-names = "default";
|
|
|
|
snps,mtl-rx-config = <&mtl_rx_setup>;
|
|
snps,mtl-tx-config = <&mtl_tx_setup>;
|
|
snps,ps-speed = <1000>;
|
|
|
|
status = "okay";
|
|
|
|
mdio {
|
|
compatible = "snps,dwmac-mdio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
phy0: phy@8 {
|
|
compatible = "ethernet-phy-id31c3.1c33";
|
|
reg = <0x8>;
|
|
device_type = "ethernet-phy";
|
|
interrupts-extended = <&tlmm 4 IRQ_TYPE_EDGE_FALLING>;
|
|
reset-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
|
|
reset-assert-us = <11000>;
|
|
reset-deassert-us = <70000>;
|
|
};
|
|
};
|
|
|
|
mtl_rx_setup: rx-queues-config {
|
|
snps,rx-queues-to-use = <4>;
|
|
snps,rx-sched-sp;
|
|
|
|
queue0 {
|
|
snps,dcb-algorithm;
|
|
snps,map-to-dma-channel = <0x0>;
|
|
snps,route-up;
|
|
snps,priority = <0x1>;
|
|
};
|
|
|
|
queue1 {
|
|
snps,dcb-algorithm;
|
|
snps,map-to-dma-channel = <0x1>;
|
|
snps,route-ptp;
|
|
};
|
|
|
|
queue2 {
|
|
snps,avb-algorithm;
|
|
snps,map-to-dma-channel = <0x2>;
|
|
snps,route-avcp;
|
|
};
|
|
|
|
queue3 {
|
|
snps,avb-algorithm;
|
|
snps,map-to-dma-channel = <0x3>;
|
|
snps,priority = <0xc>;
|
|
};
|
|
};
|
|
|
|
mtl_tx_setup: tx-queues-config {
|
|
snps,tx-queues-to-use = <4>;
|
|
|
|
queue0 {
|
|
snps,dcb-algorithm;
|
|
};
|
|
|
|
queue1 {
|
|
snps,dcb-algorithm;
|
|
};
|
|
|
|
queue2 {
|
|
snps,avb-algorithm;
|
|
snps,send_slope = <0x1000>;
|
|
snps,idle_slope = <0x1000>;
|
|
snps,high_credit = <0x3e800>;
|
|
snps,low_credit = <0xffc18000>;
|
|
};
|
|
|
|
queue3 {
|
|
snps,avb-algorithm;
|
|
snps,send_slope = <0x1000>;
|
|
snps,idle_slope = <0x1000>;
|
|
snps,high_credit = <0x3e800>;
|
|
snps,low_credit = <0xffc18000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpu {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpu_zap_shader {
|
|
firmware-name = "qcom/qcs8300/a623_zap.mbn";
|
|
};
|
|
|
|
&i2c8 {
|
|
clock-frequency = <400000>;
|
|
|
|
status = "okay";
|
|
|
|
io_expander: gpio@74 {
|
|
compatible = "ti,tca9539";
|
|
reg = <0x74>;
|
|
interrupts-extended = <&tlmm 93 IRQ_TYPE_EDGE_BOTH>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
reset-gpios = <&tlmm 66 GPIO_ACTIVE_LOW>;
|
|
|
|
pinctrl-0 = <&io_expander_intr_active>,
|
|
<&io_expander_reset_active>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
i2c-mux@70 {
|
|
compatible = "nxp,pca9543";
|
|
reg = <0x70>;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
i2c@0 {
|
|
reg = <0>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
bridge@58 {
|
|
compatible = "analogix,anx7625";
|
|
reg = <0x58>;
|
|
interrupts-extended = <&io_expander 2 IRQ_TYPE_EDGE_FALLING>;
|
|
enable-gpios = <&io_expander 1 GPIO_ACTIVE_HIGH>;
|
|
reset-gpios = <&io_expander 0 GPIO_ACTIVE_HIGH>;
|
|
vdd10-supply = <&vreg_1p0>;
|
|
vdd18-supply = <&vreg_1p8>;
|
|
vdd33-supply = <&vreg_3p0>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
|
|
dsi2dp_bridge_in: endpoint {
|
|
|
|
remote-endpoint = <&mdss_dsi0_out>;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
|
|
dsi2dp_bridge_out: endpoint {
|
|
|
|
remote-endpoint = <&dp_dsi0_connector_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pmm8650au_1_gpios {
|
|
usb2_en: usb2-en-state {
|
|
pins = "gpio7";
|
|
function = "normal";
|
|
output-enable;
|
|
power-source = <0>;
|
|
};
|
|
};
|
|
|
|
&iris {
|
|
status = "okay";
|
|
};
|
|
|
|
&mdss {
|
|
status = "okay";
|
|
};
|
|
|
|
&mdss_dp0 {
|
|
pinctrl-0 = <&dp_hot_plug_det>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&mdss_dp0_out {
|
|
data-lanes = <0 1 2 3>;
|
|
link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
|
|
remote-endpoint = <&dp0_connector_in>;
|
|
};
|
|
|
|
&mdss_dp0_phy {
|
|
vdda-phy-supply = <&vreg_l5a>;
|
|
vdda-pll-supply = <&vreg_l4a>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie0 {
|
|
pinctrl-0 = <&pcie0_default_state>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&pcieport0 {
|
|
reset-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
|
|
wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
|
|
|
|
wifi@0 {
|
|
compatible = "pci17cb,1103";
|
|
reg = <0x10000 0x0 0x0 0x0 0x0>;
|
|
|
|
vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
|
|
vddaon-supply = <&vreg_pmu_aon_0p59>;
|
|
vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
|
|
vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
|
|
vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
|
|
vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
|
|
vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
|
|
vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
|
|
vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
|
|
|
|
qcom,calibration-variant = "QC_QCS8300_Ride";
|
|
};
|
|
};
|
|
|
|
&pcie0_phy {
|
|
vdda-phy-supply = <&vreg_l6a>;
|
|
vdda-pll-supply = <&vreg_l5a>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie1 {
|
|
pinctrl-0 = <&pcie1_default_state>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&pcieport1 {
|
|
reset-gpios = <&tlmm 23 GPIO_ACTIVE_LOW>;
|
|
wake-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
&pcie1_phy {
|
|
vdda-phy-supply = <&vreg_l6a>;
|
|
vdda-pll-supply = <&vreg_l5a>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&mdss_dsi0 {
|
|
vdda-supply = <&vreg_l5a>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&mdss_dsi0_phy {
|
|
vdds-supply = <&vreg_l4a>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&mdss_dsi0_out {
|
|
data-lanes = <0 1 2 3>;
|
|
remote-endpoint = <&dsi2dp_bridge_in>;
|
|
};
|
|
|
|
&qupv3_id_0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&qupv3_id_1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&remoteproc_adsp {
|
|
firmware-name = "qcom/qcs8300/adsp.mbn";
|
|
status = "okay";
|
|
};
|
|
|
|
&remoteproc_cdsp {
|
|
firmware-name = "qcom/qcs8300/cdsp0.mbn";
|
|
status = "okay";
|
|
};
|
|
|
|
&remoteproc_gpdsp {
|
|
firmware-name = "qcom/qcs8300/gpdsp0.mbn";
|
|
status = "okay";
|
|
};
|
|
|
|
&serdes0 {
|
|
phy-supply = <&vreg_l5a>;
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhc_1 {
|
|
pinctrl-0 = <&sdc1_state_on>;
|
|
pinctrl-1 = <&sdc1_state_off>;
|
|
pinctrl-names = "default", "sleep";
|
|
|
|
bus-width = <8>;
|
|
mmc-ddr-1_8v;
|
|
mmc-hs200-1_8v;
|
|
mmc-hs400-1_8v;
|
|
mmc-hs400-enhanced-strobe;
|
|
vmmc-supply = <&vreg_l8a>;
|
|
vqmmc-supply = <&vreg_s4a>;
|
|
|
|
non-removable;
|
|
no-sd;
|
|
no-sdio;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&tlmm {
|
|
bt_en_state: bt-en-state {
|
|
pins = "gpio55";
|
|
function = "gpio";
|
|
bias-pull-down;
|
|
};
|
|
|
|
pcie0_default_state: pcie0-default-state {
|
|
wake-pins {
|
|
pins = "gpio0";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
clkreq-pins {
|
|
pins = "gpio1";
|
|
function = "pcie0_clkreq";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
perst-pins {
|
|
pins = "gpio2";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-pull-down;
|
|
};
|
|
};
|
|
|
|
ethernet0_default: ethernet0-default-state {
|
|
ethernet0_mdc: ethernet0-mdc-pins {
|
|
pins = "gpio5";
|
|
function = "emac0_mdc";
|
|
drive-strength = <16>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
ethernet0_mdio: ethernet0-mdio-pins {
|
|
pins = "gpio6";
|
|
function = "emac0_mdio";
|
|
drive-strength = <16>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
pcie1_default_state: pcie1-default-state {
|
|
wake-pins {
|
|
pins = "gpio21";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
clkreq-pins {
|
|
pins = "gpio22";
|
|
function = "pcie1_clkreq";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
perst-pins {
|
|
pins = "gpio23";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-pull-down;
|
|
};
|
|
};
|
|
|
|
io_expander_reset_active: io-expander-reset-active-state {
|
|
pins = "gpio66";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
|
|
io_expander_intr_active: io-expander-intr-active-state {
|
|
pins = "gpio93";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
|
|
dp_hot_plug_det: dp-hot-plug-det-state {
|
|
pins = "gpio94";
|
|
function = "edp0_hot";
|
|
bias-disable;
|
|
};
|
|
|
|
wlan_en_state: wlan-en-state {
|
|
pins = "gpio54";
|
|
function = "gpio";
|
|
bias-pull-down;
|
|
};
|
|
};
|
|
|
|
&uart2 {
|
|
status = "okay";
|
|
|
|
bluetooth: bluetooth {
|
|
compatible = "qcom,wcn6855-bt";
|
|
firmware-name = "QCA6698/hpnv21", "QCA6698/hpbtfw21.tlv";
|
|
max-speed = <3200000>;
|
|
|
|
vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
|
|
vddaon-supply = <&vreg_pmu_aon_0p59>;
|
|
vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
|
|
vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
|
|
vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
|
|
vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
|
|
vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
|
|
vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
|
|
};
|
|
};
|
|
|
|
&uart7 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ufs_mem_hc {
|
|
reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
|
|
vcc-supply = <&vreg_l8a>;
|
|
vcc-max-microamp = <1100000>;
|
|
vccq-supply = <&vreg_l4c>;
|
|
vccq-max-microamp = <1200000>;
|
|
status = "okay";
|
|
};
|
|
|
|
&ufs_mem_phy {
|
|
vdda-phy-supply = <&vreg_l4a>;
|
|
vdda-pll-supply = <&vreg_l5a>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_1_hsphy {
|
|
vdda-pll-supply = <&vreg_l7a>;
|
|
vdda18-supply = <&vreg_l7c>;
|
|
vdda33-supply = <&vreg_l9a>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_2_hsphy {
|
|
vdda-pll-supply = <&vreg_l7a>;
|
|
vdda18-supply = <&vreg_l7c>;
|
|
vdda33-supply = <&vreg_l9a>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_qmpphy {
|
|
vdda-phy-supply = <&vreg_l7a>;
|
|
vdda-pll-supply = <&vreg_l5a>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_1 {
|
|
dr_mode = "peripheral";
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_2 {
|
|
dr_mode = "host";
|
|
|
|
status = "okay";
|
|
};
|